1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
|
/*
* ***************************************************************************
* Copyright (C) 2016 Marvell International Ltd.
* ***************************************************************************
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions are met:
*
* Redistributions of source code must retain the above copyright notice, this
* list of conditions and the following disclaimer.
*
* Redistributions in binary form must reproduce the above copyright notice,
* this list of conditions and the following disclaimer in the documentation
* and/or other materials provided with the distribution.
*
* Neither the name of Marvell nor the names of its contributors may be used
* to endorse or promote products derived from this software without specific
* prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
* ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE
* LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,
* OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
* SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
* INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
* CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
***************************************************************************
*/
#include <arch_helpers.h>
#include <plat_marvell.h>
#include <debug.h>
#include <mv_ddr_if.h>
#include <plat_def.h>
#include <mmio.h>
#include <a8k_i2c.h>
#define MVEBU_CP_MPP_CTRL37_OFFS 20
#define MVEBU_CP_MPP_CTRL38_OFFS 24
#define MVEBU_CP_MPP_CTRL37_I2C0_SCK_ENA 0x2
#define MVEBU_CP_MPP_CTRL38_I2C0_SDA_ENA 0x2
#define MVEBU_MPP_CTRL_MASK 0xf
/*
* This struct provides the DRAM training code with
* the appropriate board DRAM configuration
*/
static struct mv_ddr_topology_map board_topology_map = {
/* Board with 1CS 8Gb x4 devices of Micron 2400T */
DEBUG_LEVEL_ERROR,
0x1, /* active interfaces */
/* cs_mask, mirror, dqs_swap, ck_swap X subphys */
{ { { {0x1, 0x0, 0, 0}, /* FIXME: change the cs mask for all 64 bit */
{0x1, 0x0, 0, 0},
{0x1, 0x0, 0, 0},
{0x1, 0x0, 0, 0},
{0x1, 0x0, 0, 0},
{0x1, 0x0, 0, 0},
{0x1, 0x0, 0, 0},
{0x1, 0x0, 0, 0},
{0x1, 0x0, 0, 0} },
/* TODO: double check if the speed bin is 2400T */
SPEED_BIN_DDR_2400T, /* speed_bin */
MV_DDR_DEV_WIDTH_8BIT, /* sdram device width */
MV_DDR_DIE_CAP_8GBIT, /* die capacity */
MV_DDR_FREQ_SAR, /* frequency */
0, 0, /* cas_l, cas_wl */
MV_DDR_TEMP_LOW} }, /* temperature */
MV_DDR_64BIT_BUS_MASK, /* subphys mask */
MV_DDR_CFG_SPD, /* ddr configuration data source */
{ {0} }, /* raw spd data */
{0} /* timing parameters */
};
struct mv_ddr_topology_map *mv_ddr_topology_map_get(void)
{
/* Return the board topology as defined in the board code */
return &board_topology_map;
}
static void mpp_config(void)
{
uint32_t val;
uintptr_t reg = MVEBU_CP_MPP_REGS(0, 4);
/* configure CP0 MPP 37 and 38 to i2c */
val = mmio_read_32(reg);
val &= ~((MVEBU_MPP_CTRL_MASK << MVEBU_CP_MPP_CTRL37_OFFS) |
(MVEBU_MPP_CTRL_MASK << MVEBU_CP_MPP_CTRL38_OFFS));
val |= (MVEBU_CP_MPP_CTRL37_I2C0_SCK_ENA << MVEBU_CP_MPP_CTRL37_OFFS) |
(MVEBU_CP_MPP_CTRL38_I2C0_SDA_ENA << MVEBU_CP_MPP_CTRL38_OFFS);
mmio_write_32(reg, val);
}
/*
* This function may modify the default DRAM parameters
* based on information recieved from SPD or bootloader
* configuration located on non volatile storage
*/
void plat_dram_update_topology(void)
{
struct mv_ddr_topology_map *tm = mv_ddr_topology_map_get();
INFO("Gathering DRAM information\n");
if (tm->cfg_src == MV_DDR_CFG_SPD) {
/* configure MPPs to enable i2c */
mpp_config();
/* initialize the i2c */
i2c_init((void *)MVEBU_CP0_I2C_BASE);
/* select SPD memory page 0 to access DRAM configuration */
i2c_write(I2C_SPD_P0_ADDR, 0x0, 1, tm->spd_data.all_bytes, 1);
/* read data from spd */
i2c_read(I2C_SPD_ADDR, 0x0, 1, tm->spd_data.all_bytes,
sizeof(tm->spd_data.all_bytes));
}
}
|