diff options
| -rw-r--r-- | Documentation/devicetree/bindings/hwmon/pwm-fan.txt | 29 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/mfd/s2mps11.txt | 4 | ||||
| -rw-r--r-- | arch/arm/boot/dts/Makefile | 2 | ||||
| -rw-r--r-- | arch/arm/boot/dts/exynos4412-odroidu3.dts | 43 | ||||
| -rw-r--r-- | arch/arm/boot/dts/exynos4412.dtsi | 1 | ||||
| -rw-r--r-- | arch/arm/boot/dts/exynos5250-snow-common.dtsi | 684 | ||||
| -rw-r--r-- | arch/arm/boot/dts/exynos5250-snow-rev5.dts | 47 | ||||
| -rw-r--r-- | arch/arm/boot/dts/exynos5250-snow.dts | 671 | ||||
| -rw-r--r-- | arch/arm/boot/dts/exynos5422-odroidxu3-audio.dtsi | 61 | ||||
| -rw-r--r-- | arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi | 99 | ||||
| -rw-r--r-- | arch/arm/boot/dts/exynos5422-odroidxu3-lite.dts | 51 | ||||
| -rw-r--r-- | arch/arm/boot/dts/exynos5422-odroidxu3.dts | 51 | ||||
| -rw-r--r-- | arch/arm/boot/dts/exynos5422-odroidxu4.dts | 48 |
13 files changed, 1025 insertions, 766 deletions
diff --git a/Documentation/devicetree/bindings/hwmon/pwm-fan.txt b/Documentation/devicetree/bindings/hwmon/pwm-fan.txt index 610757ce4492..c6d533202d3e 100644 --- a/Documentation/devicetree/bindings/hwmon/pwm-fan.txt +++ b/Documentation/devicetree/bindings/hwmon/pwm-fan.txt @@ -3,10 +3,35 @@ Bindings for a fan connected to the PWM lines Required properties: - compatible : "pwm-fan" - pwms : the PWM that is used to control the PWM fan +- cooling-levels : PWM duty cycle values in a range from 0 to 255 + which correspond to thermal cooling states Example: - pwm-fan { + fan0: pwm-fan { compatible = "pwm-fan"; - status = "okay"; + cooling-min-state = <0>; + cooling-max-state = <3>; + #cooling-cells = <2>; pwms = <&pwm 0 10000 0>; + cooling-levels = <0 102 170 230>; }; + + thermal-zones { + cpu_thermal: cpu-thermal { + thermal-sensors = <&tmu 0>; + polling-delay-passive = <0>; + polling-delay = <0>; + trips { + cpu_alert1: cpu-alert1 { + temperature = <100000>; /* millicelsius */ + hysteresis = <2000>; /* millicelsius */ + type = "passive"; + }; + }; + cooling-maps { + map0 { + trip = <&cpu_alert1>; + cooling-device = <&fan0 0 1>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/s2mps11.txt b/Documentation/devicetree/bindings/mfd/s2mps11.txt index 57a045016fca..90eaef393325 100644 --- a/Documentation/devicetree/bindings/mfd/s2mps11.txt +++ b/Documentation/devicetree/bindings/mfd/s2mps11.txt @@ -15,6 +15,10 @@ Optional properties: - interrupt-parent: Specifies the phandle of the interrupt controller to which the interrupts from s2mps11 are delivered to. - interrupts: Interrupt specifiers for interrupt sources. +- samsung,s2mps11-acokb-ground: Indicates that ACOKB pin of S2MPS11 PMIC is + connected to the ground so the PMIC must manually set PWRHOLD bit in CTRL1 + register to turn off the power. Usually the ACOKB is pulled up to VBATT so + when PWRHOLD pin goes low, the rising ACOKB will trigger power off. Optional nodes: - clocks: s2mps11, s2mps13 and s5m8767 provide three(AP/CP/BT) buffered 32.768 diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 233159d2eaab..bc6649dcba5c 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -115,6 +115,7 @@ dtb-$(CONFIG_ARCH_EXYNOS5) += \ exynos5250-arndale.dtb \ exynos5250-smdk5250.dtb \ exynos5250-snow.dtb \ + exynos5250-snow-rev5.dtb \ exynos5250-spring.dtb \ exynos5260-xyref5260.dtb \ exynos5410-smdk5410.dtb \ @@ -123,6 +124,7 @@ dtb-$(CONFIG_ARCH_EXYNOS5) += \ exynos5420-smdk5420.dtb \ exynos5422-odroidxu3.dtb \ exynos5422-odroidxu3-lite.dtb \ + exynos5422-odroidxu4.dtb \ exynos5440-sd5v1.dtb \ exynos5440-ssdk5440.dtb \ exynos5800-peach-pi.dtb diff --git a/arch/arm/boot/dts/exynos4412-odroidu3.dts b/arch/arm/boot/dts/exynos4412-odroidu3.dts index 8632f35c6c26..1e6ef99eef59 100644 --- a/arch/arm/boot/dts/exynos4412-odroidu3.dts +++ b/arch/arm/boot/dts/exynos4412-odroidu3.dts @@ -32,6 +32,49 @@ linux,default-trigger = "heartbeat"; }; }; + + fan0: pwm-fan { + compatible = "pwm-fan"; + pwms = <&pwm 0 10000 0>; + cooling-min-state = <0>; + cooling-max-state = <3>; + #cooling-cells = <2>; + cooling-levels = <0 102 170 230>; + }; + + thermal-zones { + cpu_thermal: cpu-thermal { + cooling-maps { + map0 { + trip = <&cpu_alert1>; + cooling-device = <&cpu0 7 7>; + }; + map1 { + trip = <&cpu_alert2>; + cooling-device = <&cpu0 13 13>; + }; + map2 { + trip = <&cpu_alert0>; + cooling-device = <&fan0 0 1>; + }; + map3 { + trip = <&cpu_alert1>; + cooling-device = <&fan0 1 2>; + }; + map4 { + trip = <&cpu_alert2>; + cooling-device = <&fan0 2 3>; + }; + }; + }; + }; +}; + +&pwm { + pinctrl-0 = <&pwm0_out>; + pinctrl-names = "default"; + samsung,pwm-outputs = <0>; + status = "okay"; }; &usb3503 { diff --git a/arch/arm/boot/dts/exynos4412.dtsi b/arch/arm/boot/dts/exynos4412.dtsi index ca0e3c15977f..294cfe40388d 100644 --- a/arch/arm/boot/dts/exynos4412.dtsi +++ b/arch/arm/boot/dts/exynos4412.dtsi @@ -98,6 +98,7 @@ opp-hz = /bits/ 64 <800000000>; opp-microvolt = <1000000>; clock-latency-ns = <200000>; + opp-suspend; }; opp07 { opp-hz = /bits/ 64 <900000000>; diff --git a/arch/arm/boot/dts/exynos5250-snow-common.dtsi b/arch/arm/boot/dts/exynos5250-snow-common.dtsi new file mode 100644 index 000000000000..0a7f408824d8 --- /dev/null +++ b/arch/arm/boot/dts/exynos5250-snow-common.dtsi @@ -0,0 +1,684 @@ +/* + * Google Snow board device tree source + * + * Copyright (c) 2012 Google, Inc + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/clock/maxim,max77686.h> +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/input/input.h> +#include "exynos5250.dtsi" + +/ { + aliases { + i2c104 = &i2c_104; + }; + + memory { + reg = <0x40000000 0x80000000>; + }; + + chosen { + bootargs = "console=tty1"; + stdout-path = "serial3:115200n8"; + }; + + gpio-keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&power_key_irq &lid_irq>; + + power { + label = "Power"; + gpios = <&gpx1 3 GPIO_ACTIVE_LOW>; + linux,code = <KEY_POWER>; + gpio-key,wakeup; + }; + + lid-switch { + label = "Lid"; + gpios = <&gpx3 5 GPIO_ACTIVE_LOW>; + linux,input-type = <5>; /* EV_SW */ + linux,code = <0>; /* SW_LID */ + debounce-interval = <1>; + gpio-key,wakeup; + }; + }; + + vbat: vbat-fixed-regulator { + compatible = "regulator-fixed"; + regulator-name = "vbat-supply"; + regulator-boot-on; + }; + + i2c-arbitrator { + compatible = "i2c-arb-gpio-challenge"; + #address-cells = <1>; + #size-cells = <0>; + + i2c-parent = <&{/i2c@12CA0000}>; + + our-claim-gpio = <&gpf0 3 GPIO_ACTIVE_LOW>; + their-claim-gpios = <&gpe0 4 GPIO_ACTIVE_LOW>; + slew-delay-us = <10>; + wait-retry-us = <3000>; + wait-free-us = <50000>; + + pinctrl-names = "default"; + pinctrl-0 = <&arb_our_claim &arb_their_claim>; + + /* Use ID 104 as a hint that we're on physical bus 4 */ + i2c_104: i2c@0 { + reg = <0>; + #address-cells = <1>; + #size-cells = <0>; + + battery: sbs-battery@b { + compatible = "sbs,sbs-battery"; + reg = <0xb>; + sbs,poll-retry-count = <1>; + }; + + cros_ec: embedded-controller { + compatible = "google,cros-ec-i2c"; + reg = <0x1e>; + interrupts = <6 IRQ_TYPE_NONE>; + interrupt-parent = <&gpx1>; + pinctrl-names = "default"; + pinctrl-0 = <&ec_irq>; + wakeup-source; + }; + + power-regulator { + compatible = "ti,tps65090"; + reg = <0x48>; + + /* + * Config irq to disable internal pulls + * even though we run in polling mode. + */ + pinctrl-names = "default"; + pinctrl-0 = <&tps65090_irq>; + + vsys1-supply = <&vbat>; + vsys2-supply = <&vbat>; + vsys3-supply = <&vbat>; + infet1-supply = <&vbat>; + infet2-supply = <&vbat>; + infet3-supply = <&vbat>; + infet4-supply = <&vbat>; + infet5-supply = <&vbat>; + infet6-supply = <&vbat>; + infet7-supply = <&vbat>; + vsys-l1-supply = <&vbat>; + vsys-l2-supply = <&vbat>; + + regulators { + dcdc1 { + ti,enable-ext-control; + }; + dcdc2 { + ti,enable-ext-control; + }; + dcdc3 { + ti,enable-ext-control; + }; + fet1: fet1 { + regulator-name = "vcd_led"; + ti,overcurrent-wait = <3>; + }; + tps65090_fet2: fet2 { + regulator-name = "video_mid"; + regulator-always-on; + ti,overcurrent-wait = <3>; + }; + fet3 { + regulator-name = "wwan_r"; + regulator-always-on; + ti,overcurrent-wait = <3>; + }; + fet4 { + regulator-name = "sdcard"; + ti,overcurrent-wait = <3>; + }; + fet5 { + regulator-name = "camout"; + regulator-always-on; + ti,overcurrent-wait = <3>; + }; + fet6: fet6 { + regulator-name = "lcd_vdd"; + ti,overcurrent-wait = <3>; + }; + tps65090_fet7: fet7 { + regulator-name = "video_mid_1a"; + regulator-always-on; + ti,overcurrent-wait = <3>; + }; + ldo1 { + }; + ldo2 { + }; + }; + + charger { + compatible = "ti,tps65090-charger"; + }; + }; + }; + }; + + sound { + samsung,i2s-controller = <&i2s0>; + }; + + usb3_vbus_reg: regulator-usb3 { + compatible = "regulator-fixed"; + regulator-name = "P5.0V_USB3CON"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpx2 7 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&usb3_vbus_en>; + enable-active-high; + }; + + fixed-rate-clocks { + xxti { + compatible = "samsung,clock-xxti"; + clock-frequency = <24000000>; + }; + }; + + backlight: backlight { + compatible = "pwm-backlight"; + pwms = <&pwm 0 1000000 0>; + brightness-levels = <0 100 500 1000 1500 2000 2500 2800>; + default-brightness-level = <7>; + enable-gpios = <&gpx3 0 GPIO_ACTIVE_HIGH>; + power-supply = <&fet1>; + pinctrl-0 = <&pwm0_out>; + pinctrl-names = "default"; + }; + + panel: panel { + compatible = "auo,b116xw03"; + power-supply = <&fet6>; + backlight = <&backlight>; + + port { + panel_in: endpoint { + remote-endpoint = <&bridge_out>; + }; + }; + }; + + mmc3_pwrseq: mmc3_pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&gpx0 2 GPIO_ACTIVE_LOW>, /* WIFI_RSTn */ + <&gpx0 1 GPIO_ACTIVE_LOW>; /* WIFI_EN */ + clocks = <&max77686 MAX77686_CLK_PMIC>; + clock-names = "ext_clock"; + }; +}; + +&cpu0 { + cpu0-supply = <&buck2_reg>; +}; + +&dp { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&dp_hpd>; + samsung,color-space = <0>; + samsung,dynamic-range = <0>; + samsung,ycbcr-coeff = <0>; + samsung,color-depth = <1>; + samsung,link-rate = <0x0a>; + samsung,lane-count = <2>; + samsung,hpd-gpio = <&gpx0 7 GPIO_ACTIVE_HIGH>; + + ports { + port@0 { + dp_out: endpoint { + remote-endpoint = <&bridge_in>; + }; + }; + }; +}; + +&ehci { + samsung,vbus-gpio = <&gpx1 1 GPIO_ACTIVE_HIGH>; +}; + +&fimd { + status = "okay"; + samsung,invert-vclk; +}; + +&hdmi { + hpd-gpio = <&gpx3 7 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&hdmi_hpd_irq>; + phy = <&hdmiphy>; + ddc = <&i2c_2>; + hdmi-en-supply = <&tps65090_fet7>; + vdd-supply = <&ldo8_reg>; + vdd_osc-supply = <&ldo10_reg>; + vdd_pll-supply = <&ldo8_reg>; +}; + +&i2c_0 { + status = "okay"; + samsung,i2c-sda-delay = <100>; + samsung,i2c-max-bus-freq = <378000>; + + max77686: max77686@09 { + compatible = "maxim,max77686"; + interrupt-parent = <&gpx3>; + interrupts = <2 IRQ_TYPE_NONE>; + pinctrl-names = "default"; + pinctrl-0 = <&max77686_irq>; + wakeup-source; + reg = <0x09>; + #clock-cells = <1>; + + voltage-regulators { + ldo1_reg: LDO1 { + regulator-name = "P1.0V_LDO_OUT1"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + }; + + ldo2_reg: LDO2 { + regulator-name = "P1.8V_LDO_OUT2"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + ldo3_reg: LDO3 { + regulator-name = "P1.8V_LDO_OUT3"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + ldo7_reg: LDO7 { + regulator-name = "P1.1V_LDO_OUT7"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + }; + + ldo8_reg: LDO8 { + regulator-name = "P1.0V_LDO_OUT8"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + }; + + ldo10_reg: LDO10 { + regulator-name = "P1.8V_LDO_OUT10"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + ldo12_reg: LDO12 { + regulator-name = "P3.0V_LDO_OUT12"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-always-on; + }; + + ldo14_reg: LDO14 { + regulator-name = "P1.8V_LDO_OUT14"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + ldo15_reg: LDO15 { + regulator-name = "P1.0V_LDO_OUT15"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + }; + + ldo16_reg: LDO16 { + regulator-name = "P1.8V_LDO_OUT16"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + buck1_reg: BUCK1 { + regulator-name = "vdd_mif"; + regulator-min-microvolt = <950000>; + regulator-max-microvolt = <1300000>; + regulator-always-on; + regulator-boot-on; + }; + + buck2_reg: BUCK2 { + regulator-name = "vdd_arm"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-boot-on; + }; + + buck3_reg: BUCK3 { + regulator-name = "vdd_int"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + regulator-boot-on; + }; + + buck4_reg: BUCK4 { + regulator-name = "vdd_g3d"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1300000>; + regulator-always-on; + regulator-boot-on; + }; + + buck5_reg: BUCK5 { + regulator-name = "P1.8V_BUCK_OUT5"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + buck6_reg: BUCK6 { + regulator-name = "P1.35V_BUCK_OUT6"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + }; + + buck7_reg: BUCK7 { + regulator-name = "P2.0V_BUCK_OUT7"; + regulator-min-microvolt = <2000000>; + regulator-max-microvolt = <2000000>; + regulator-always-on; + }; + + buck8_reg: BUCK8 { + regulator-name = "P2.85V_BUCK_OUT8"; + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + regulator-always-on; + }; + }; + }; +}; + +&i2c_1 { + status = "okay"; + samsung,i2c-sda-delay = <100>; + samsung,i2c-max-bus-freq = <378000>; + + trackpad { + reg = <0x67>; + compatible = "cypress,cyapa"; + interrupts = <2 IRQ_TYPE_NONE>; + interrupt-parent = <&gpx1>; + wakeup-source; + }; +}; + +/* + * Disabled pullups since external part has its own pullups and + * double-pulling gets us out of spec in some cases. + */ +&i2c2_bus { + samsung,pin-pud = <0>; +}; + +&i2c_2 { + status = "okay"; + samsung,i2c-sda-delay = <100>; + samsung,i2c-max-bus-freq = <66000>; + + hdmiddc@50 { + compatible = "samsung,exynos4210-hdmiddc"; + reg = <0x50>; + }; +}; + +&i2c_3 { + status = "okay"; + samsung,i2c-sda-delay = <100>; + samsung,i2c-max-bus-freq = <66000>; +}; + +&i2c_4 { + status = "okay"; + samsung,i2c-sda-delay = <100>; + samsung,i2c-max-bus-freq = <66000>; +}; + +&i2c_5 { + status = "okay"; + samsung,i2c-sda-delay = <100>; + samsung,i2c-max-bus-freq = <66000>; +}; + +&i2c_7 { + status = "okay"; + samsung,i2c-sda-delay = <100>; + samsung,i2c-max-bus-freq = <66000>; + + ptn3460: lvds-bridge@20 { + compatible = "nxp,ptn3460"; + reg = <0x20>; + powerdown-gpios = <&gpy2 5 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpx1 5 GPIO_ACTIVE_HIGH>; + edid-emulation = <5>; + + ports { + port@0 { + bridge_out: endpoint { + remote-endpoint = <&panel_in>; + }; + }; + + port@1 { + bridge_in: endpoint { + remote-endpoint = <&dp_out>; + }; + }; + }; + }; +}; + +&i2c_8 { + status = "okay"; + samsung,i2c-sda-delay = <100>; + samsung,i2c-max-bus-freq = <378000>; + + hdmiphy: hdmiphy@38 { + compatible = "samsung,exynos4212-hdmiphy"; + reg = <0x38>; + }; +}; + +&i2s0 { + status = "okay"; +}; + +&mmc_0 { + status = "okay"; + num-slots = <1>; + broken-cd; + card-detect-delay = <200>; + samsung,dw-mshc-ciu-div = <3>; + samsung,dw-mshc-sdr-timing = <2 3>; + samsung,dw-mshc-ddr-timing = <1 2>; + pinctrl-names = "default"; + pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_cd &sd0_bus4 &sd0_bus8>; + bus-width = <8>; + cap-mmc-highspeed; +}; + +&mmc_2 { + status = "okay"; + num-slots = <1>; + card-detect-delay = <200>; + samsung,dw-mshc-ciu-div = <3>; + samsung,dw-mshc-sdr-timing = <2 3>; + samsung,dw-mshc-ddr-timing = <1 2>; + pinctrl-names = "default"; + pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>; + bus-width = <4>; + wp-gpios = <&gpc2 1 GPIO_ACTIVE_HIGH>; + cap-sd-highspeed; +}; + +/* + * On Snow we've got SIP WiFi and so can keep drive strengths low to + * reduce EMI. + */ +&mmc_3 { + status = "okay"; + num-slots = <1>; + broken-cd; + cap-sdio-irq; + keep-power-in-suspend; + card-detect-delay = <200>; + samsung,dw-mshc-ciu-div = <3>; + samsung,dw-mshc-sdr-timing = <2 3>; + samsung,dw-mshc-ddr-timing = <1 2>; + pinctrl-names = "default"; + pinctrl-0 = <&sd3_clk &sd3_cmd &sd3_bus4 &wifi_en &wifi_rst>; + bus-width = <4>; + cap-sd-highspeed; + mmc-pwrseq = <&mmc3_pwrseq>; +}; + +&pinctrl_0 { + wifi_en: wifi-en { + samsung,pins = "gpx0-1"; + samsung,pin-function = <1>; + samsung,pin-pud = <0>; + samsung,pin-drv = <0>; + }; + + wifi_rst: wifi-rst { + samsung,pins = "gpx0-2"; + samsung,pin-function = <1>; + samsung,pin-pud = <0>; + samsung,pin-drv = <0>; + }; + + power_key_irq: power-key-irq { + samsung,pins = "gpx1-3"; + samsung,pin-function = <0xf>; + samsung,pin-pud = <0>; + samsung,pin-drv = <0>; + }; + + ec_irq: ec-irq { + samsung,pins = "gpx1-6"; + samsung,pin-function = <0>; + samsung,pin-pud = <0>; + samsung,pin-drv = <0>; + }; + + tps65090_irq: tps65090-irq { + samsung,pins = "gpx2-6"; + samsung,pin-function = <0>; + samsung,pin-pud = <0>; + samsung,pin-drv = <0>; + }; + + usb3_vbus_en: usb3-vbus-en { + samsung,pins = "gpx2-7"; + samsung,pin-function = <1>; + samsung,pin-pud = <0>; + samsung,pin-drv = <0>; + }; + + max77686_irq: max77686-irq { + samsung,pins = "gpx3-2"; + samsung,pin-function = <0>; + samsung,pin-pud = <0>; + samsung,pin-drv = <0>; + }; + + lid_irq: lid-irq { + samsung,pins = "gpx3-5"; + samsung,pin-function = <0xf>; + samsung,pin-pud = <0>; + samsung,pin-drv = <0>; + }; + + hdmi_hpd_irq: hdmi-hpd-irq { + samsung,pins = "gpx3-7"; + samsung,pin-function = <0>; + samsung,pin-pud = <1>; + samsung,pin-drv = <0>; + }; +}; + +&pinctrl_1 { + arb_their_claim: arb-their-claim { + samsung,pins = "gpe0-4"; + samsung,pin-function = <0>; + samsung,pin-pud = <3>; + samsung,pin-drv = <0>; + }; + + arb_our_claim: arb-our-claim { + samsung,pins = "gpf0-3"; + samsung,pin-function = <1>; + samsung,pin-pud = <0>; + samsung,pin-drv = <0>; + }; +}; + +&rtc { + status = "okay"; + clocks = <&clock CLK_RTC>, <&max77686 MAX77686_CLK_AP>; + clock-names = "rtc", "rtc_src"; +}; + +&sd3_bus4 { + samsung,pin-drv = <0>; +}; + +&sd3_clk { + samsung,pin-drv = <0>; +}; + +&sd3_cmd { + samsung,pin-pud = <3>; + samsung,pin-drv = <0>; +}; + +&spi_1 { + status = "okay"; + samsung,spi-src-clk = <0>; + num-cs = <1>; + cs-gpios = <&gpa2 5 GPIO_ACTIVE_HIGH>; +}; + +&usbdrd_dwc3 { + dr_mode = "host"; +}; + +&usbdrd_phy { + vbus-supply = <&usb3_vbus_reg>; +}; + +#include "cros-ec-keyboard.dtsi" diff --git a/arch/arm/boot/dts/exynos5250-snow-rev5.dts b/arch/arm/boot/dts/exynos5250-snow-rev5.dts new file mode 100644 index 000000000000..f811dc800660 --- /dev/null +++ b/arch/arm/boot/dts/exynos5250-snow-rev5.dts @@ -0,0 +1,47 @@ +/* + * Google Snow Rev 5+ board device tree source + * + * Copyright (c) 2012 Google, Inc + * Copyright (c) 2015 Samsung Electronics Co., Ltd. + * http://www.samsung.com + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/dts-v1/; +#include "exynos5250-snow-common.dtsi" + +/ { + model = "Google Snow Rev 5+"; + compatible = "google,snow-rev5", "samsung,exynos5250", + "samsung,exynos5"; + + sound { + compatible = "google,snow-audio-max98090"; + + samsung,model = "Snow-I2S-MAX98090"; + samsung,audio-codec = <&max98090>; + }; +}; + +&i2c_7 { + max98090: codec@10 { + compatible = "maxim,max98090"; + reg = <0x10>; + interrupts = <4 IRQ_TYPE_NONE>; + interrupt-parent = <&gpx0>; + pinctrl-names = "default"; + pinctrl-0 = <&max98090_irq>; + }; +}; + +&pinctrl_0 { + max98090_irq: max98090-irq { + samsung,pins = "gpx0-4"; + samsung,pin-function = <0>; + samsung,pin-pud = <0>; + samsung,pin-drv = <0>; + }; +}; diff --git a/arch/arm/boot/dts/exynos5250-snow.dts b/arch/arm/boot/dts/exynos5250-snow.dts index 0720caab5511..995c7ce6c12b 100644 --- a/arch/arm/boot/dts/exynos5250-snow.dts +++ b/arch/arm/boot/dts/exynos5250-snow.dts @@ -9,698 +9,35 @@ */ /dts-v1/; -#include <dt-bindings/gpio/gpio.h> -#include <dt-bindings/clock/maxim,max77686.h> -#include <dt-bindings/interrupt-controller/irq.h> -#include <dt-bindings/input/input.h> -#include "exynos5250.dtsi" +#include "exynos5250-snow-common.dtsi" / { model = "Google Snow"; - compatible = "google,snow", "samsung,exynos5250", "samsung,exynos5"; - - aliases { - i2c104 = &i2c_104; - }; - - memory { - reg = <0x40000000 0x80000000>; - }; - - chosen { - bootargs = "console=tty1"; - stdout-path = "serial3:115200n8"; - }; - - gpio-keys { - compatible = "gpio-keys"; - pinctrl-names = "default"; - pinctrl-0 = <&power_key_irq &lid_irq>; - - power { - label = "Power"; - gpios = <&gpx1 3 GPIO_ACTIVE_LOW>; - linux,code = <KEY_POWER>; - gpio-key,wakeup; - }; - - lid-switch { - label = "Lid"; - gpios = <&gpx3 5 GPIO_ACTIVE_LOW>; - linux,input-type = <5>; /* EV_SW */ - linux,code = <0>; /* SW_LID */ - debounce-interval = <1>; - gpio-key,wakeup; - }; - }; - - vbat: vbat-fixed-regulator { - compatible = "regulator-fixed"; - regulator-name = "vbat-supply"; - regulator-boot-on; - }; - - i2c-arbitrator { - compatible = "i2c-arb-gpio-challenge"; - #address-cells = <1>; - #size-cells = <0>; - - i2c-parent = <&{/i2c@12CA0000}>; - - our-claim-gpio = <&gpf0 3 GPIO_ACTIVE_LOW>; - their-claim-gpios = <&gpe0 4 GPIO_ACTIVE_LOW>; - slew-delay-us = <10>; - wait-retry-us = <3000>; - wait-free-us = <50000>; - - pinctrl-names = "default"; - pinctrl-0 = <&arb_our_claim &arb_their_claim>; - - /* Use ID 104 as a hint that we're on physical bus 4 */ - i2c_104: i2c@0 { - reg = <0>; - #address-cells = <1>; - #size-cells = <0>; - - battery: sbs-battery@b { - compatible = "sbs,sbs-battery"; - reg = <0xb>; - sbs,poll-retry-count = <1>; - }; - - cros_ec: embedded-controller { - compatible = "google,cros-ec-i2c"; - reg = <0x1e>; - interrupts = <6 IRQ_TYPE_NONE>; - interrupt-parent = <&gpx1>; - pinctrl-names = "default"; - pinctrl-0 = <&ec_irq>; - wakeup-source; - }; - - power-regulator { - compatible = "ti,tps65090"; - reg = <0x48>; - - /* - * Config irq to disable internal pulls - * even though we run in polling mode. - */ - pinctrl-names = "default"; - pinctrl-0 = <&tps65090_irq>; - - vsys1-supply = <&vbat>; - vsys2-supply = <&vbat>; - vsys3-supply = <&vbat>; - infet1-supply = <&vbat>; - infet2-supply = <&vbat>; - infet3-supply = <&vbat>; - infet4-supply = <&vbat>; - infet5-supply = <&vbat>; - infet6-supply = <&vbat>; - infet7-supply = <&vbat>; - vsys-l1-supply = <&vbat>; - vsys-l2-supply = <&vbat>; - - regulators { - dcdc1 { - ti,enable-ext-control; - }; - dcdc2 { - ti,enable-ext-control; - }; - dcdc3 { - ti,enable-ext-control; - }; - fet1: fet1 { - regulator-name = "vcd_led"; - ti,overcurrent-wait = <3>; - }; - tps65090_fet2: fet2 { - regulator-name = "video_mid"; - regulator-always-on; - ti,overcurrent-wait = <3>; - }; - fet3 { - regulator-name = "wwan_r"; - regulator-always-on; - ti,overcurrent-wait = <3>; - }; - fet4 { - regulator-name = "sdcard"; - ti,overcurrent-wait = <3>; - }; - fet5 { - regulator-name = "camout"; - regulator-always-on; - ti,overcurrent-wait = <3>; - }; - fet6: fet6 { - regulator-name = "lcd_vdd"; - ti,overcurrent-wait = <3>; - }; - tps65090_fet7: fet7 { - regulator-name = "video_mid_1a"; - regulator-always-on; - ti,overcurrent-wait = <3>; - }; - ldo1 { - }; - ldo2 { - }; - }; - - charger { - compatible = "ti,tps65090-charger"; - }; - }; - }; - }; + compatible = "google,snow-rev4", "google,snow", "samsung,exynos5250", + "samsung,exynos5"; sound { compatible = "google,snow-audio-max98095"; samsung,model = "Snow-I2S-MAX98095"; - samsung,i2s-controller = <&i2s0>; samsung,audio-codec = <&max98095>; }; - - usb3_vbus_reg: regulator-usb3 { - compatible = "regulator-fixed"; - regulator-name = "P5.0V_USB3CON"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - gpio = <&gpx2 7 GPIO_ACTIVE_HIGH>; - pinctrl-names = "default"; - pinctrl-0 = <&usb3_vbus_en>; - enable-active-high; - }; - - fixed-rate-clocks { - xxti { - compatible = "samsung,clock-xxti"; - clock-frequency = <24000000>; - }; - }; - - backlight: backlight { - compatible = "pwm-backlight"; - pwms = <&pwm 0 1000000 0>; - brightness-levels = <0 100 500 1000 1500 2000 2500 2800>; - default-brightness-level = <7>; - enable-gpios = <&gpx3 0 GPIO_ACTIVE_HIGH>; - power-supply = <&fet1>; - pinctrl-0 = <&pwm0_out>; - pinctrl-names = "default"; - }; - - panel: panel { - compatible = "auo,b116xw03"; - power-supply = <&fet6>; - backlight = <&backlight>; - - port { - panel_in: endpoint { - remote-endpoint = <&bridge_out>; - }; - }; - }; - - mmc3_pwrseq: mmc3_pwrseq { - compatible = "mmc-pwrseq-simple"; - reset-gpios = <&gpx0 2 GPIO_ACTIVE_LOW>, /* WIFI_RSTn */ - <&gpx0 1 GPIO_ACTIVE_LOW>; /* WIFI_EN */ - clocks = <&max77686 MAX77686_CLK_PMIC>; - clock-names = "ext_clock"; - }; -}; - -&cpu0 { - cpu0-supply = <&buck2_reg>; -}; - -&dp { - status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&dp_hpd>; - samsung,color-space = <0>; - samsung,dynamic-range = <0>; - samsung,ycbcr-coeff = <0>; - samsung,color-depth = <1>; - samsung,link-rate = <0x0a>; - samsung,lane-count = <2>; - samsung,hpd-gpio = <&gpx0 7 GPIO_ACTIVE_HIGH>; - - ports { - port@0 { - dp_out: endpoint { - remote-endpoint = <&bridge_in>; - }; - }; - }; -}; - -&ehci { - samsung,vbus-gpio = <&gpx1 1 GPIO_ACTIVE_HIGH>; -}; - -&fimd { - status = "okay"; - samsung,invert-vclk; -}; - -&hdmi { - hpd-gpio = <&gpx3 7 GPIO_ACTIVE_HIGH>; - pinctrl-names = "default"; - pinctrl-0 = <&hdmi_hpd_irq>; - phy = <&hdmiphy>; - ddc = <&i2c_2>; - hdmi-en-supply = <&tps65090_fet7>; - vdd-supply = <&ldo8_reg>; - vdd_osc-supply = <&ldo10_reg>; - vdd_pll-supply = <&ldo8_reg>; -}; - -&i2c_0 { - status = "okay"; - samsung,i2c-sda-delay = <100>; - samsung,i2c-max-bus-freq = <378000>; - - max77686: max77686@09 { - compatible = "maxim,max77686"; - interrupt-parent = <&gpx3>; - interrupts = <2 IRQ_TYPE_NONE>; - pinctrl-names = "default"; - pinctrl-0 = <&max77686_irq>; - wakeup-source; - reg = <0x09>; - #clock-cells = <1>; - - voltage-regulators { - ldo1_reg: LDO1 { - regulator-name = "P1.0V_LDO_OUT1"; - regulator-min-microvolt = <1000000>; - regulator-max-microvolt = <1000000>; - regulator-always-on; - }; - - ldo2_reg: LDO2 { - regulator-name = "P1.8V_LDO_OUT2"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-always-on; - }; - - ldo3_reg: LDO3 { - regulator-name = "P1.8V_LDO_OUT3"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-always-on; - }; - - ldo7_reg: LDO7 { - regulator-name = "P1.1V_LDO_OUT7"; - regulator-min-microvolt = <1100000>; - regulator-max-microvolt = <1100000>; - regulator-always-on; - }; - - ldo8_reg: LDO8 { - regulator-name = "P1.0V_LDO_OUT8"; - regulator-min-microvolt = <1000000>; - regulator-max-microvolt = <1000000>; - regulator-always-on; - }; - - ldo10_reg: LDO10 { - regulator-name = "P1.8V_LDO_OUT10"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-always-on; - }; - - ldo12_reg: LDO12 { - regulator-name = "P3.0V_LDO_OUT12"; - regulator-min-microvolt = <3000000>; - regulator-max-microvolt = <3000000>; - regulator-always-on; - }; - - ldo14_reg: LDO14 { - regulator-name = "P1.8V_LDO_OUT14"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-always-on; - }; - - ldo15_reg: LDO15 { - regulator-name = "P1.0V_LDO_OUT15"; - regulator-min-microvolt = <1000000>; - regulator-max-microvolt = <1000000>; - regulator-always-on; - }; - - ldo16_reg: LDO16 { - regulator-name = "P1.8V_LDO_OUT16"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-always-on; - }; - - buck1_reg: BUCK1 { - regulator-name = "vdd_mif"; - regulator-min-microvolt = <950000>; - regulator-max-microvolt = <1300000>; - regulator-always-on; - regulator-boot-on; - }; - - buck2_reg: BUCK2 { - regulator-name = "vdd_arm"; - regulator-min-microvolt = <850000>; - regulator-max-microvolt = <1350000>; - regulator-always-on; - regulator-boot-on; - }; - - buck3_reg: BUCK3 { - regulator-name = "vdd_int"; - regulator-min-microvolt = <900000>; - regulator-max-microvolt = <1200000>; - regulator-always-on; - regulator-boot-on; - }; - - buck4_reg: BUCK4 { - regulator-name = "vdd_g3d"; - regulator-min-microvolt = <850000>; - regulator-max-microvolt = <1300000>; - regulator-always-on; - regulator-boot-on; - }; - - buck5_reg: BUCK5 { - regulator-name = "P1.8V_BUCK_OUT5"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-always-on; - regulator-boot-on; - }; - - buck6_reg: BUCK6 { - regulator-name = "P1.35V_BUCK_OUT6"; - regulator-min-microvolt = <1350000>; - regulator-max-microvolt = <1350000>; - regulator-always-on; - }; - - buck7_reg: BUCK7 { - regulator-name = "P2.0V_BUCK_OUT7"; - regulator-min-microvolt = <2000000>; - regulator-max-microvolt = <2000000>; - regulator-always-on; - }; - - buck8_reg: BUCK8 { - regulator-name = "P2.85V_BUCK_OUT8"; - regulator-min-microvolt = <2850000>; - regulator-max-microvolt = <2850000>; - regulator-always-on; - }; - }; - }; -}; - -&i2c_1 { - status = "okay"; - samsung,i2c-sda-delay = <100>; - samsung,i2c-max-bus-freq = <378000>; - - trackpad { - reg = <0x67>; - compatible = "cypress,cyapa"; - interrupts = <2 IRQ_TYPE_NONE>; - interrupt-parent = <&gpx1>; - wakeup-source; - }; -}; - -/* - * Disabled pullups since external part has its own pullups and - * double-pulling gets us out of spec in some cases. - */ -&i2c2_bus { - samsung,pin-pud = <0>; -}; - -&i2c_2 { - status = "okay"; - samsung,i2c-sda-delay = <100>; - samsung,i2c-max-bus-freq = <66000>; - - hdmiddc@50 { - compatible = "samsung,exynos4210-hdmiddc"; - reg = <0x50>; - }; -}; - -&i2c_3 { - status = "okay"; - samsung,i2c-sda-delay = <100>; - samsung,i2c-max-bus-freq = <66000>; -}; - -&i2c_4 { - status = "okay"; - samsung,i2c-sda-delay = <100>; - samsung,i2c-max-bus-freq = <66000>; -}; - -&i2c_5 { - status = "okay"; - samsung,i2c-sda-delay = <100>; - samsung,i2c-max-bus-freq = <66000>; }; &i2c_7 { - status = "okay"; - samsung,i2c-sda-delay = <100>; - samsung,i2c-max-bus-freq = <66000>; - - ptn3460: lvds-bridge@20 { - compatible = "nxp,ptn3460"; - reg = <0x20>; - powerdown-gpios = <&gpy2 5 GPIO_ACTIVE_HIGH>; - reset-gpios = <&gpx1 5 GPIO_ACTIVE_HIGH>; - edid-emulation = <5>; - - ports { - port@0 { - bridge_out: endpoint { - remote-endpoint = <&panel_in>; - }; - }; - - port@1 { - bridge_in: endpoint { - remote-endpoint = <&dp_out>; - }; - }; - }; - }; - max98095: codec@11 { compatible = "maxim,max98095"; reg = <0x11>; - pinctrl-0 = <&max98095_en>; pinctrl-names = "default"; + pinctrl-0 = <&max98095_en>; }; }; -&i2c_8 { - status = "okay"; - samsung,i2c-sda-delay = <100>; - samsung,i2c-max-bus-freq = <378000>; - - hdmiphy: hdmiphy@38 { - compatible = "samsung,exynos4212-hdmiphy"; - reg = <0x38>; - }; -}; - -&i2s0 { - status = "okay"; -}; - -&mmc_0 { - status = "okay"; - num-slots = <1>; - broken-cd; - card-detect-delay = <200>; - samsung,dw-mshc-ciu-div = <3>; - samsung,dw-mshc-sdr-timing = <2 3>; - samsung,dw-mshc-ddr-timing = <1 2>; - pinctrl-names = "default"; - pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_cd &sd0_bus4 &sd0_bus8>; - bus-width = <8>; - cap-mmc-highspeed; -}; - -&mmc_2 { - status = "okay"; - num-slots = <1>; - card-detect-delay = <200>; - samsung,dw-mshc-ciu-div = <3>; - samsung,dw-mshc-sdr-timing = <2 3>; - samsung,dw-mshc-ddr-timing = <1 2>; - pinctrl-names = "default"; - pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>; - bus-width = <4>; - wp-gpios = <&gpc2 1 GPIO_ACTIVE_HIGH>; - cap-sd-highspeed; -}; - -/* - * On Snow we've got SIP WiFi and so can keep drive strengths low to - * reduce EMI. - */ -&mmc_3 { - status = "okay"; - num-slots = <1>; - broken-cd; - cap-sdio-irq; - keep-power-in-suspend; - card-detect-delay = <200>; - samsung,dw-mshc-ciu-div = <3>; - samsung,dw-mshc-sdr-timing = <2 3>; - samsung,dw-mshc-ddr-timing = <1 2>; - pinctrl-names = "default"; - pinctrl-0 = <&sd3_clk &sd3_cmd &sd3_bus4 &wifi_en &wifi_rst>; - bus-width = <4>; - cap-sd-highspeed; - mmc-pwrseq = <&mmc3_pwrseq>; -}; - &pinctrl_0 { - wifi_en: wifi-en { - samsung,pins = "gpx0-1"; - samsung,pin-function = <1>; - samsung,pin-pud = <0>; - samsung,pin-drv = <0>; - }; - - wifi_rst: wifi-rst { - samsung,pins = "gpx0-2"; - samsung,pin-function = <1>; - samsung,pin-pud = <0>; - samsung,pin-drv = <0>; - }; - - power_key_irq: power-key-irq { - samsung,pins = "gpx1-3"; - samsung,pin-function = <0xf>; - samsung,pin-pud = <0>; - samsung,pin-drv = <0>; - }; - - ec_irq: ec-irq { - samsung,pins = "gpx1-6"; - samsung,pin-function = <0>; - samsung,pin-pud = <0>; - samsung,pin-drv = <0>; - }; - max98095_en: max98095-en { samsung,pins = "gpx1-7"; samsung,pin-function = <0>; samsung,pin-pud = <3>; samsung,pin-drv = <0>; }; - - tps65090_irq: tps65090-irq { - samsung,pins = "gpx2-6"; - samsung,pin-function = <0>; - samsung,pin-pud = <0>; - samsung,pin-drv = <0>; - }; - - usb3_vbus_en: usb3-vbus-en { - samsung,pins = "gpx2-7"; - samsung,pin-function = <1>; - samsung,pin-pud = <0>; - samsung,pin-drv = <0>; - }; - - max77686_irq: max77686-irq { - samsung,pins = "gpx3-2"; - samsung,pin-function = <0>; - samsung,pin-pud = <0>; - samsung,pin-drv = <0>; - }; - - lid_irq: lid-irq { - samsung,pins = "gpx3-5"; - samsung,pin-function = <0xf>; - samsung,pin-pud = <0>; - samsung,pin-drv = <0>; - }; - - hdmi_hpd_irq: hdmi-hpd-irq { - samsung,pins = "gpx3-7"; - samsung,pin-function = <0>; - samsung,pin-pud = <1>; - samsung,pin-drv = <0>; - }; -}; - -&pinctrl_1 { - arb_their_claim: arb-their-claim { - samsung,pins = "gpe0-4"; - samsung,pin-function = <0>; - samsung,pin-pud = <3>; - samsung,pin-drv = <0>; - }; - - arb_our_claim: arb-our-claim { - samsung,pins = "gpf0-3"; - samsung,pin-function = <1>; - samsung,pin-pud = <0>; - samsung,pin-drv = <0>; - }; }; - -&rtc { - status = "okay"; - clocks = <&clock CLK_RTC>, <&max77686 MAX77686_CLK_AP>; - clock-names = "rtc", "rtc_src"; -}; - -&sd3_bus4 { - samsung,pin-drv = <0>; -}; - -&sd3_clk { - samsung,pin-drv = <0>; -}; - -&sd3_cmd { - samsung,pin-pud = <3>; - samsung,pin-drv = <0>; -}; - -&spi_1 { - status = "okay"; - samsung,spi-src-clk = <0>; - num-cs = <1>; - cs-gpios = <&gpa2 5 GPIO_ACTIVE_HIGH>; -}; - -&usbdrd_dwc3 { - dr_mode = "host"; -}; - -&usbdrd_phy { - vbus-supply = <&usb3_vbus_reg>; -}; - -#include "cros-ec-keyboard.dtsi" diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3-audio.dtsi b/arch/arm/boot/dts/exynos5422-odroidxu3-audio.dtsi new file mode 100644 index 000000000000..9493923ec652 --- /dev/null +++ b/arch/arm/boot/dts/exynos5422-odroidxu3-audio.dtsi @@ -0,0 +1,61 @@ +/* + * Hardkernel Odroid XU3 Audio Codec device tree source + * + * Copyright (c) 2015 Krzysztof Kozlowski + * Copyright (c) 2014 Collabora Ltd. + * Copyright (c) 2013 Samsung Electronics Co., Ltd. + * http://www.samsung.com + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +/ { + sound: sound { + compatible = "simple-audio-card"; + + simple-audio-card,name = "Odroid-XU3"; + simple-audio-card,widgets = + "Headphone", "Headphone Jack", + "Speakers", "Speakers"; + simple-audio-card,routing = + "Headphone Jack", "HPL", + "Headphone Jack", "HPR", + "Headphone Jack", "MICBIAS", + "IN1", "Headphone Jack", + "Speakers", "SPKL", + "Speakers", "SPKR"; + + simple-audio-card,format = "i2s"; + simple-audio-card,bitclock-master = <&link0_codec>; + simple-audio-card,frame-master = <&link0_codec>; + + simple-audio-card,cpu { + sound-dai = <&i2s0 0>; + system-clock-frequency = <19200000>; + }; + + link0_codec: simple-audio-card,codec { + sound-dai = <&max98090>; + clocks = <&i2s0 CLK_I2S_CDCLK>; + }; + }; +}; + +&hsi2c_5 { + status = "okay"; + max98090: max98090@10 { + compatible = "maxim,max98090"; + reg = <0x10>; + interrupt-parent = <&gpx3>; + interrupts = <2 0>; + clocks = <&i2s0 CLK_I2S_CDCLK>; + clock-names = "mclk"; + #sound-dai-cells = <0>; + }; +}; + +&i2s0 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi index 79ffdfe712aa..a83d569baea8 100644 --- a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi +++ b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi @@ -46,70 +46,6 @@ reset-gpios = <&gpd1 0 1>; }; - pwmleds { - compatible = "pwm-leds"; - - greenled { - label = "green:mmc0"; - pwms = <&pwm 1 2000000 0>; - pwm-names = "pwm1"; - /* - * Green LED is much brighter than the others - * so limit its max brightness - */ - max_brightness = <127>; - linux,default-trigger = "mmc0"; - }; - - blueled { - label = "blue:heartbeat"; - pwms = <&pwm 2 2000000 0>; - pwm-names = "pwm2"; - max_brightness = <255>; - linux,default-trigger = "heartbeat"; - }; - }; - - gpioleds { - compatible = "gpio-leds"; - redled { - label = "red:microSD"; - gpios = <&gpx2 3 GPIO_ACTIVE_HIGH>; - default-state = "off"; - linux,default-trigger = "mmc1"; - }; - }; - - sound: sound { - compatible = "simple-audio-card"; - - simple-audio-card,name = "Odroid-XU3"; - simple-audio-card,widgets = - "Headphone", "Headphone Jack", - "Speakers", "Speakers"; - simple-audio-card,routing = - "Headphone Jack", "HPL", - "Headphone Jack", "HPR", - "Headphone Jack", "MICBIAS", - "IN1", "Headphone Jack", - "Speakers", "SPKL", - "Speakers", "SPKR"; - - simple-audio-card,format = "i2s"; - simple-audio-card,bitclock-master = <&link0_codec>; - simple-audio-card,frame-master = <&link0_codec>; - - simple-audio-card,cpu { - sound-dai = <&i2s0 0>; - system-clock-frequency = <19200000>; - }; - - link0_codec: simple-audio-card,codec { - sound-dai = <&max98090>; - clocks = <&i2s0 CLK_I2S_CDCLK>; - }; - }; - fan0: pwm-fan { compatible = "pwm-fan"; pwms = <&pwm 0 20972 0>; @@ -160,6 +96,7 @@ s2mps11,buck2-ramp-enable = <1>; s2mps11,buck3-ramp-enable = <1>; s2mps11,buck4-ramp-enable = <1>; + samsung,s2mps11-acokb-ground; interrupt-parent = <&gpx0>; interrupts = <4 IRQ_TYPE_EDGE_FALLING>; @@ -375,19 +312,6 @@ }; }; -&hsi2c_5 { - status = "okay"; - max98090: max98090@10 { - compatible = "maxim,max98090"; - reg = <0x10>; - interrupt-parent = <&gpx3>; - interrupts = <2 0>; - clocks = <&i2s0 CLK_I2S_CDCLK>; - clock-names = "mclk"; - #sound-dai-cells = <0>; - }; -}; - &i2c_2 { samsung,i2c-sda-delay = <100>; samsung,i2c-max-bus-freq = <66000>; @@ -399,10 +323,6 @@ }; }; -&i2s0 { - status = "okay"; -}; - &mfc { samsung,mfc-r = <0x43000000 0x800000>; samsung,mfc-l = <0x51000000 0x800000>; @@ -463,19 +383,6 @@ }; }; -&pwm { - /* - * PWM 0 -- fan - * PWM 1 -- Green LED - * PWM 2 -- Blue LED - * PWM 3 -- on MIPI connector for backlight - */ - pinctrl-0 = <&pwm0_out &pwm1_out &pwm2_out &pwm3_out>; - pinctrl-names = "default"; - samsung,pwm-outputs = <0>; - status = "okay"; -}; - &tmu_cpu0 { vtmu-supply = <&ldo7_reg>; status = "okay"; @@ -511,9 +418,7 @@ dr_mode = "host"; }; -&usbdrd_dwc3_1 { - dr_mode = "otg"; -}; +/* usbdrd_dwc3_1 mode customized in each board */ &usbdrd3_0 { vdd33-supply = <&ldo9_reg>; diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3-lite.dts b/arch/arm/boot/dts/exynos5422-odroidxu3-lite.dts index c06882bbb822..b1b36081f343 100644 --- a/arch/arm/boot/dts/exynos5422-odroidxu3-lite.dts +++ b/arch/arm/boot/dts/exynos5422-odroidxu3-lite.dts @@ -13,8 +13,59 @@ /dts-v1/; #include "exynos5422-odroidxu3-common.dtsi" +#include "exynos5422-odroidxu3-audio.dtsi" / { model = "Hardkernel Odroid XU3 Lite"; compatible = "hardkernel,odroid-xu3-lite", "samsung,exynos5800", "samsung,exynos5"; + + pwmleds { + compatible = "pwm-leds"; + + greenled { + label = "green:mmc0"; + pwms = <&pwm 1 2000000 0>; + pwm-names = "pwm1"; + /* + * Green LED is much brighter than the others + * so limit its max brightness + */ + max_brightness = <127>; + linux,default-trigger = "mmc0"; + }; + + blueled { + label = "blue:heartbeat"; + pwms = <&pwm 2 2000000 0>; + pwm-names = "pwm2"; + max_brightness = <255>; + linux,default-trigger = "heartbeat"; + }; + }; + + gpioleds { + compatible = "gpio-leds"; + redled { + label = "red:microSD"; + gpios = <&gpx2 3 GPIO_ACTIVE_HIGH>; + default-state = "off"; + linux,default-trigger = "mmc1"; + }; + }; +}; + +&pwm { + /* + * PWM 0 -- fan + * PWM 1 -- Green LED + * PWM 2 -- Blue LED + * PWM 3 -- on MIPI connector for backlight + */ + pinctrl-0 = <&pwm0_out &pwm1_out &pwm2_out &pwm3_out>; + pinctrl-names = "default"; + status = "okay"; +}; + +&usbdrd_dwc3_1 { + dr_mode = "otg"; }; diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3.dts b/arch/arm/boot/dts/exynos5422-odroidxu3.dts index 78e6a502f320..0c0bbdbfd85f 100644 --- a/arch/arm/boot/dts/exynos5422-odroidxu3.dts +++ b/arch/arm/boot/dts/exynos5422-odroidxu3.dts @@ -12,10 +12,45 @@ /dts-v1/; #include "exynos5422-odroidxu3-common.dtsi" +#include "exynos5422-odroidxu3-audio.dtsi" / { model = "Hardkernel Odroid XU3"; compatible = "hardkernel,odroid-xu3", "samsung,exynos5800", "samsung,exynos5"; + + pwmleds { + compatible = "pwm-leds"; + + greenled { + label = "green:mmc0"; + pwms = <&pwm 1 2000000 0>; + pwm-names = "pwm1"; + /* + * Green LED is much brighter than the others + * so limit its max brightness + */ + max_brightness = <127>; + linux,default-trigger = "mmc0"; + }; + + blueled { + label = "blue:heartbeat"; + pwms = <&pwm 2 2000000 0>; + pwm-names = "pwm2"; + max_brightness = <255>; + linux,default-trigger = "heartbeat"; + }; + }; + + gpioleds { + compatible = "gpio-leds"; + redled { + label = "red:microSD"; + gpios = <&gpx2 3 GPIO_ACTIVE_HIGH>; + default-state = "off"; + linux,default-trigger = "mmc1"; + }; + }; }; &i2c_0 { @@ -49,3 +84,19 @@ shunt-resistor = <10000>; }; }; + +&pwm { + /* + * PWM 0 -- fan + * PWM 1 -- Green LED + * PWM 2 -- Blue LED + * PWM 3 -- on MIPI connector for backlight + */ + pinctrl-0 = <&pwm0_out &pwm1_out &pwm2_out &pwm3_out>; + pinctrl-names = "default"; + status = "okay"; +}; + +&usbdrd_dwc3_1 { + dr_mode = "otg"; +}; diff --git a/arch/arm/boot/dts/exynos5422-odroidxu4.dts b/arch/arm/boot/dts/exynos5422-odroidxu4.dts new file mode 100644 index 000000000000..2faf88627a48 --- /dev/null +++ b/arch/arm/boot/dts/exynos5422-odroidxu4.dts @@ -0,0 +1,48 @@ +/* + * Hardkernel Odroid XU4 board device tree source + * + * Copyright (c) 2015 Krzysztof Kozlowski + * Copyright (c) 2014 Collabora Ltd. + * Copyright (c) 2013-2015 Samsung Electronics Co., Ltd. + * http://www.samsung.com + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +/dts-v1/; +#include "exynos5422-odroidxu3-common.dtsi" + +/ { + model = "Hardkernel Odroid XU4"; + compatible = "hardkernel,odroid-xu4", "samsung,exynos5800", \ + "samsung,exynos5"; + + pwmleds { + compatible = "pwm-leds"; + + blueled { + label = "blue:heartbeat"; + pwms = <&pwm 2 2000000 0>; + pwm-names = "pwm2"; + max_brightness = <255>; + linux,default-trigger = "heartbeat"; + }; + }; +}; + +&pwm { + /* + * PWM 0 -- fan + * PWM 2 -- Blue LED + */ + pinctrl-0 = <&pwm0_out &pwm2_out>; + pinctrl-names = "default"; + samsung,pwm-outputs = <0>, <2>; + status = "okay"; +}; + +&usbdrd_dwc3_1 { + dr_mode = "host"; +}; |