| Age | Commit message (Collapse) | Author |
|---|
|
gpiochip_lock_as_irq() may return a few error codes,
do not shadow them by -EINVAL and let caller to decide.
No functional change intended.
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
gpiochip_lock_as_irq() may return a few error codes,
do not shadow them by -EINVAL and let caller to decide.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
In Rockchip RK3328, the output only GPIO_MUTE pin, originally for codec
mute control, can also be used for general purpose. It is manipulated by
the GRF_SOC_CON10 register in GRF. Aside from the GPIO_MUTE pin, the HDMI
pins can also be set in the same way.
Currently this GRF GPIO controller only supports the mute pin. If needed
in the future, the HDMI pins support can also be added.
Signed-off-by: Levin Du <djw@t-chip.com.cn>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This should make applications utilizing whole banks work faster.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
PWM2 is commonly used to control voltage of PWM regulator of VDD_LOG in
RK3399. On the Firefly-RK3399 board, PWM2 outputs 40 KHz square wave
from power on and the VDD_LOG is about 0.9V. When the kernel boots
normally into the system, the PWM2 keeps outputing PWM signal.
But the kernel hangs randomly after "Starting kernel ..." line on that
board. When it happens, PWM2 outputs high level which causes VDD_LOG
drops to 0.4V below the normal operating voltage.
By adding "pclk_rkpwm_pmu" to the rk3399_pmucru_critical_clocks array,
PWM clock is ensured to be prepared at startup and the PWM2 output is
normal. After repeated tests, the early boot hang is gone.
This patch works on both Firefly-RK3399 and ROC-RK3399-PC boards.
Signed-off-by: Levin Du <djw@t-chip.com.cn>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Use unsigned int, because it's preferred to unsigned.
Signed-off-by: Kitone Elvis Peter <elviskitone@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
|
|
drm_sched_job_finish() is a work item scheduled for each finished job on
a unbound system workqueue. This means the workers can execute out of order
with regard to the real hardware job completions.
If this happens queueing a timeout worker for the first job on the ring
mirror list is wrong, as this may be a job which has already finished
executing. Fix this by reorganizing the code to always queue the worker
for the next job on the list, if this job hasn't finished yet. This is
robust against a potential reordering of the finish workers.
Also move out the timeout worker cancelling, so that we don't need to
take the job list lock twice. As a small optimization list_del is used
to remove the job from the ring mirror list, as there is no need to
reinit the list head in the job we are about to free.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
for vega, dp set_panel_mode is
handled by psp firmware. dal should not program the
register again.
[how]
dal does not program panel mode.
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
When programming tonga's connector's backend we didn't take
in account that HDMI's colour depth might be more than 8bpc
therefore we need to add a switch statement that would adjust
the pixel clock accordingly.
[how]
Add a switch statement updating clock by its appropriate
coefficient.
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
[Why]
We seem to have an issue where high enough display clock
will not get set properly during S3 resume if we only
call vbios once
[How]
Expand condition of display clock programming to happen
even when cached display clock matches requested display
clock
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
The pointer for integrated_info can be NULL which causes the system to
do a null pointer deference and hang on boot.
[How]
Add a check to ensure that integrated_info is not null before enabling
DP ss.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
TPACKET_V3 stores variable length frames in fixed length blocks.
Blocks must be able to store a block header, optional private space
and at least one minimum sized frame.
Frames, even for a zero snaplen packet, store metadata headers and
optional reserved space.
In the block size bounds check, ensure that the frame of the
chosen configuration fits. This includes sockaddr_ll and optional
tp_reserve.
Syzbot was able to construct a ring with insuffient room for the
sockaddr_ll in the header of a zero-length frame, triggering an
out-of-bounds write in dev_parse_header.
Convert the comparison to less than, as zero is a valid snap len.
This matches the test for minimum tp_frame_size immediately below.
Fixes: f6fb8f100b80 ("af-packet: TPACKET_V3 flexible buffer implementation.")
Fixes: eb73190f4fbe ("net/packet: refine check for priv area size")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit d94a155c59c9 ("x86/cpu: Prevent cpuinfo_x86::x86_phys_bits
adjustment corruption") has moved the query and calculation of the
x86_virt_bits and x86_phys_bits fields of the cpuinfo_x86 struct
from the get_cpu_cap function to a new function named
get_cpu_address_sizes.
One of the call sites related to Xen PV VMs was unfortunately missed
in the aforementioned commit. This prevents successful boot-up of
kernel versions 4.17 and up in Xen PV VMs if CONFIG_DEBUG_VIRTUAL
is enabled, due to the following code path:
enlighten_pv.c::xen_start_kernel
mmu_pv.c::xen_reserve_special_pages
page.h::__pa
physaddr.c::__phys_addr
physaddr.h::phys_addr_valid
phys_addr_valid uses boot_cpu_data.x86_phys_bits to validate physical
addresses. boot_cpu_data.x86_phys_bits is no longer populated before
the call to xen_reserve_special_pages due to the aforementioned commit
though, so the validation performed by phys_addr_valid fails, which
causes __phys_addr to trigger a BUG, preventing boot-up.
Signed-off-by: M. Vefa Bicakci <m.v.b@runbox.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: xen-devel@lists.xenproject.org
Cc: x86@kernel.org
Cc: stable@vger.kernel.org # for v4.17 and up
Fixes: d94a155c59c9 ("x86/cpu: Prevent cpuinfo_x86::x86_phys_bits adjustment corruption")
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sschmidt/wpan-next
Stefan Schmidt says:
====================
pull-request: ieee802154-next 2018-08-06
An update from ieee802154 for *net-next*
Romuald added a socket option to get the LQI value of the received datagram.
Alexander added a new hardware simulation driver modelled after hwsim of the
wireless people. It allows runtime configuration for new nodes and edges over a
netlink interface (a config utlity is making its way into wpan-tools).
We also have three fixes in here. One from Colin which is more of a cleanup and
two from Alex fixing tailroom and single frame space problems.
I would normally put the last two into my fixes tree, but given we are already
in -rc8 I simply put them here and added a cc: stable to them.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We accidentally removed the parentheses here, but they are required
because '!' has higher precedence than '&'.
Fixes: fa0f527358bd ("ip: use rb trees for IP frag queue.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 701b3a3c0ac4 ("PATCH scripts/kernel-doc") fixed the two
instances of literal braces that Perl 5.28 warns about, but there are
still more than it doesn't warn about.
Escape all left braces that are treated as literal characters. Also
escape literal right braces, for consistency and to avoid confusing
bracket-matching in text editors.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
Variable cfg_val is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'cfg_val' set but not used [-Wunused-but-set-variable]
[ Background info about val_bit field from alsa-devel ML thread:
tiwai: Actually this made me wonder what is the definition of val_bit.
It seems always 1 in the current code after the commit
964ca8083c02. Pierre?
pbossart: This val_bit is only there for debug/test, it should be set
to one by default and has nothing to do with the lpcm_id.
This variable was set even in patches before upstream
submission and was never needed, I guess it must be a 9-yr
old issue. Good catch!
]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
[why]
Prevent clock source sharing between HDMI and DP connectors.
DP shouldn't be sharing its ref clock with phy clock,
which caused an issue of older ASICS booting up with multiple
diplays plugged in.
[how]
Add an extra check that would prevent HDMI and DP sharing clk.
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
[why] dp hbr2 eye diagram pattern for raven asic is not stabled.
workaround is to use tp4 pattern. But this should not be
applied to asic before raven.
[how] add new bool varilable in asic caps. for raven asic,
use the workaround. for carrizo, vega, do not use workaround.
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
The calculated values for actual disp_clk_khz were ignored when
notifying pplib of the new display requirements. In order to honor DFS
bypass clocks from the hardware, the calculated value should be used.
[How]
The return value for set_dispclk is now assigned back into new_clocks
and correctly carried through into dccg->clks.phyclk_khz. When notifying
pplib of new display requirements dccg->clks.phyclk_khz is used
instead of dce.dispclk_khz. The value of dce.dispclk_khz was never
explicitly set to anything before.
A 15% higher display clock value than calculated is no longer requested
for dce110 since it now makes use of the calculated value.
Since dce112 makes use of dce110's set_bandwidth but not its
update_clocks it needs to have the value correctly carried through.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Custom degamma lut functions are a feature we would
like to support on compatible hardware
[How]
In atomic check, convert from array of drm_color_lut to
dc_transfer_func. On hardware commit, allow for possibility
of custom degamma. Both are based on the equivalent
regamma pipeline.
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
In the dce112 function to destroy the resource pool, engines
(the aux engines) is destroyed twice. This has no ill effects
but is a tad redundant.
[How]
Remove the redundant call
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
If there is no program explicitly setting the backlight
brightness (for example, during a minimal install of linux), the
hardware defaults to maximum brightness but the backlight_device
defaults to 0 value. Thus, settings displays the wrong brightness
value.
[How]
When creating the backlight device, set brightness to max
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
This hook that is supposed to read the actual backlight value
is used in a few places throughout the kernel to setup or force
update on backlight
[How]
Create a dc function that calls the existing abm function, and
call that function from amdgpu
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
400.1.1 is failing because we are not performing link training when
we get an HPD pulse for the same display. This is breaking DP
compliance
[How]
Always perform link training after HPD pulse if the detection
reason is not DETECT_REASON_HPDRX.
Signed-off-by: abdoulaye berthe <abdoulaye.berthe@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
The DRM mode's HDMI picture aspect ratio field was never saved in
dc_stream's timing struct. This causes us to mistake a new stream to
have the same timings as the old, even though the user has requested a
different aspect ratio.
[How]
Save DRM's aspect ratio field within dc_stream's timing struct.
Bug: https://bugs.freedesktop.org/show_bug.cgi?id=107153
Signed-off-by: Leo (Sunpeng) Li <sunpeng.li@amd.com>
Reviewed-by: Mikita Lipski <Mikita.Lipski@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Integrate the PTI Global bit fixes which conflict with the 32bit PTI
support.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
The kernel image is mapped into two places in the virtual address space
(addresses without KASLR, of course):
1. The kernel direct map (0xffff880000000000)
2. The "high kernel map" (0xffffffff81000000)
We actually execute out of #2. If we get the address of a kernel symbol,
it points to #2, but almost all physical-to-virtual translations point to
Parts of the "high kernel map" alias are mapped in the userspace page
tables with the Global bit for performance reasons. The parts that we map
to userspace do not (er, should not) have secrets. When PTI is enabled then
the global bit is usually not set in the high mapping and just used to
compensate for poor performance on systems which lack PCID.
This is fine, except that some areas in the kernel image that are adjacent
to the non-secret-containing areas are unused holes. We free these holes
back into the normal page allocator and reuse them as normal kernel memory.
The memory will, of course, get *used* via the normal map, but the alias
mapping is kept.
This otherwise unused alias mapping of the holes will, by default keep the
Global bit, be mapped out to userspace, and be vulnerable to Meltdown.
Remove the alias mapping of these pages entirely. This is likely to
fracture the 2M page mapping the kernel image near these areas, but this
should affect a minority of the area.
The pageattr code changes *all* aliases mapping the physical pages that it
operates on (by default). We only want to modify a single alias, so we
need to tweak its behavior.
This unmapping behavior is currently dependent on PTI being in place.
Going forward, we should at least consider doing this for all
configurations. Having an extra read-write alias for memory is not exactly
ideal for debugging things like random memory corruption and this does
undercut features like DEBUG_PAGEALLOC or future work like eXclusive Page
Frame Ownership (XPFO).
Before this patch:
current_kernel:---[ High Kernel Mapping ]---
current_kernel-0xffffffff80000000-0xffffffff81000000 16M pmd
current_kernel-0xffffffff81000000-0xffffffff81e00000 14M ro PSE GLB x pmd
current_kernel-0xffffffff81e00000-0xffffffff81e11000 68K ro GLB x pte
current_kernel-0xffffffff81e11000-0xffffffff82000000 1980K RW NX pte
current_kernel-0xffffffff82000000-0xffffffff82600000 6M ro PSE GLB NX pmd
current_kernel-0xffffffff82600000-0xffffffff82c00000 6M RW PSE NX pmd
current_kernel-0xffffffff82c00000-0xffffffff82e00000 2M RW NX pte
current_kernel-0xffffffff82e00000-0xffffffff83200000 4M RW PSE NX pmd
current_kernel-0xffffffff83200000-0xffffffffa0000000 462M pmd
current_user:---[ High Kernel Mapping ]---
current_user-0xffffffff80000000-0xffffffff81000000 16M pmd
current_user-0xffffffff81000000-0xffffffff81e00000 14M ro PSE GLB x pmd
current_user-0xffffffff81e00000-0xffffffff81e11000 68K ro GLB x pte
current_user-0xffffffff81e11000-0xffffffff82000000 1980K RW NX pte
current_user-0xffffffff82000000-0xffffffff82600000 6M ro PSE GLB NX pmd
current_user-0xffffffff82600000-0xffffffffa0000000 474M pmd
After this patch:
current_kernel:---[ High Kernel Mapping ]---
current_kernel-0xffffffff80000000-0xffffffff81000000 16M pmd
current_kernel-0xffffffff81000000-0xffffffff81e00000 14M ro PSE GLB x pmd
current_kernel-0xffffffff81e00000-0xffffffff81e11000 68K ro GLB x pte
current_kernel-0xffffffff81e11000-0xffffffff82000000 1980K pte
current_kernel-0xffffffff82000000-0xffffffff82400000 4M ro PSE GLB NX pmd
current_kernel-0xffffffff82400000-0xffffffff82488000 544K ro NX pte
current_kernel-0xffffffff82488000-0xffffffff82600000 1504K pte
current_kernel-0xffffffff82600000-0xffffffff82c00000 6M RW PSE NX pmd
current_kernel-0xffffffff82c00000-0xffffffff82c0d000 52K RW NX pte
current_kernel-0xffffffff82c0d000-0xffffffff82dc0000 1740K pte
current_user:---[ High Kernel Mapping ]---
current_user-0xffffffff80000000-0xffffffff81000000 16M pmd
current_user-0xffffffff81000000-0xffffffff81e00000 14M ro PSE GLB x pmd
current_user-0xffffffff81e00000-0xffffffff81e11000 68K ro GLB x pte
current_user-0xffffffff81e11000-0xffffffff82000000 1980K pte
current_user-0xffffffff82000000-0xffffffff82400000 4M ro PSE GLB NX pmd
current_user-0xffffffff82400000-0xffffffff82488000 544K ro NX pte
current_user-0xffffffff82488000-0xffffffff82600000 1504K pte
current_user-0xffffffff82600000-0xffffffffa0000000 474M pmd
[ tglx: Do not unmap on 32bit as there is only one mapping ]
Fixes: 0f561fce4d69 ("x86/pti: Enable global pages for shared areas")
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Kees Cook <keescook@google.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Joerg Roedel <jroedel@suse.de>
Link: https://lkml.kernel.org/r/20180802225831.5F6A2BFC@viggo.jf.intel.com
|
|
gvt_pin_guest_page extracted some of the gvt_dma_map_page functionality:
commit 79e542f5af79 ("drm/i915/kvmgt: Support setting dma map for huge pages")
And yet, part of it was reintroduced in:
commit 39b4cbadb9a9 ("drm/i915/kvmgt: Check the pfn got from vfio_pin_pages")
Causing kvmgt part to no longer build. Let's remove it.
Reported-by: Tomasz Lis <tomasz.lis@intel.com>
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Cc: Changbin Du <changbin.du@intel.com>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Acked-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180712155330.32055-1-michal.winiarski@intel.com
(cherry picked from commit 4eaf317a60fbea0555b936035002ca9bd9b9105d)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
Using HCI_VENDOR_PKT for vendor specific events does work since it has
also the value 0xff, but it is actually the packet type indicator
constant and not the event constant. So introduce HCI_EV_VENDOR and
use it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
The LPE audio is a child device of i915, it is powered up and down
alongside the igfx and presents no independent runtime interface. This
aptly fulfils the description of a "No-Callback" Device, so mark it
thus.
Fixes: 183c00350ccd ("drm/i915: Fix runtime PM for LPE audio")
Testcase: igt/pm_rpm/basic-pci-d3-state
Testcase: igt/pm_rpm/basic-rte
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180802140416.6062-1-chris@chris-wilson.co.uk
(cherry picked from commit 46e831abe864a6b59fa3de253a681c0f2ee1bf2f)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
The register for 0xe420 is unable to hold any value, including
this bit. The documentation is also mixed between having a
register bit for toggle and having a state command setup
for it. Apparently the register toggle is deprecated.
Remove the register toggle as evidence shows it's futile.
The thing remaining is an apology and humble request for
Mesa folks to resurrect their state setup for this as they
were on right track from start.
This reverts commit 0bf059f3532bb39c52d917142206a8554fc2f1c5.
Fixes: 0bf059f3532b ("drm/i915/icl: WaEnableFloatBlendOptimization")
References: HSDES#1406393558
Cc: Oscar Mateo <oscar.mateo@intel.com>
Cc: Anuj Phogat <anuj.phogat@gmail.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180730120636.26958-1-mika.kuoppala@linux.intel.com
(cherry picked from commit c358514ba8da9e235876db1628cedd19a35803c6)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
RPS provides a feedback loop where we use the load during the previous
evaluation interval to decide whether to up or down clock the GPU
frequency. Our responsiveness is split into 3 regimes, a high and low
plateau with the intent to keep the gpu clocked high to cover occasional
stalls under high load, and low despite occasional glitches under steady
low load, and inbetween. However, we run into situations like kodi where
we want to stay at low power (video decoding is done efficiently
inside the fixed function HW and doesn't need high clocks even for high
bitrate streams), but just occasionally the pipeline is more complex
than a video decode and we need a smidgen of extra GPU power to present
on time. In the high power regime, we sample at sub frame intervals with
a bias to upclocking, and conversely at low power we sample over a few
frames worth to provide what we consider to be the right levels of
responsiveness respectively. At low power, we more or less expect to be
kicked out to high power at the start of a busy sequence by waitboosting.
Prior to commit e9af4ea2b9e7 ("drm/i915: Avoid waitboosting on the active
request") whenever we missed the frame or stalled, we would immediate go
full throttle and upclock the GPU to max. But in commit e9af4ea2b9e7, we
relaxed the waitboosting to only apply if the pipeline was deep to avoid
over-committing resources for a near miss. Sadly though, a near miss is
still a miss, and perceptible as jitter in the frame delivery.
To try and prevent the near miss before having to resort to boosting
after the fact, we use the pageflip queue as an indication that we are
in an "interactive" regime and so should sample the load more frequently
to provide power before the frame misses it vblank. This will make us
more favorable to providing a small power increase (one or two bins) as
required rather than going all the way to maximum and then having to
work back down again. (We still keep the waitboosting mechanism around
just in case a dramatic change in system load requires urgent uplocking,
faster than we can provide in a few evaluation intervals.)
v2: Reduce rps_set_interactive to a boolean parameter to avoid the
confusion of what if they wanted a new power mode after pinning to a
different mode (which to choose?)
v3: Only reprogram RPS while the GT is awake, it will be set when we
wake the GT, and while off warns about being used outside of rpm.
v4: Fix deferred application of interactive mode
v5: s/state/interactive/
v6: Group the mutex with its principle in a substruct
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107111
Fixes: e9af4ea2b9e7 ("drm/i915: Avoid waitboosting on the active request")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Radoslaw Szwichtenberg <radoslaw.szwichtenberg@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180731132629.3381-1-chris@chris-wilson.co.uk
(cherry picked from commit 60548c554be2830d29d2533dad0ac8133347ee51)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
First of all don't try to read dpcd if PSR is not even supported.
But also, if read failed return -EIO instead of reporting via a
backchannel.
v2: fix dev_priv: At this level m->private is the connector. (CI/DK)
don't convert dpcd read errors to EIO. (DK)
Fixes: 5b7b30864d1d ("drm/i915/psr: Split sink status into a separate debugfs node")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180720003155.16290-1-rodrigo.vivi@intel.com
(cherry picked from commit 7a72c78bdd0a1ea1d879610542679cc680398220)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
This is a fix-up patch for below build issue with multi_v7_defconfig.
drivers/ptp/ptp_qoriq.o: In function `qoriq_ptp_probe':
ptp_qoriq.c:(.text+0xd0c): undefined reference to `__aeabi_uldivmod'
Fixes: 91305f281262 ("ptp_qoriq: support automatic configuration for ptp timer")
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The sock_flag() check is alreay inside sock_enable_timestamp(), so it is
unnecessary checking it in the caller.
void sock_enable_timestamp(struct sock *sk, int flag)
{
if (!sock_flag(sk, flag)) {
...
}
}
Signed-off-by: Yafang Shao <laoar.shao@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We use to have message like:
struct vhost_msg {
int type;
union {
struct vhost_iotlb_msg iotlb;
__u8 padding[64];
};
};
Unfortunately, there will be a hole of 32bit in 64bit machine because
of the alignment. This leads a different formats between 32bit API and
64bit API. What's more it will break 32bit program running on 64bit
machine.
So fixing this by introducing a new message type with an explicit
32bit reserved field after type like:
struct vhost_msg_v2 {
__u32 type;
__u32 reserved;
union {
struct vhost_iotlb_msg iotlb;
__u8 padding[64];
};
};
We will have a consistent ABI after switching to use this. To enable
this capability, introduce a new ioctl (VHOST_SET_BAKCEND_FEATURE) for
userspace to enable this feature (VHOST_BACKEND_F_IOTLB_V2).
Fixes: 6b1e6cc7855b ("vhost: new device IOTLB API")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The err is not modified after initalization, So remove it and make
it to be void function.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
__inet6_lookup_established() expect th->dport passed in host-endian,
not net-endian. The reason is microoptimization in __inet6_lookup(),
but if you use the lower-level helpers, you have to play by their
rules...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Jeff Layton <jlayton@kernel.org>
|
|
Signed-off-by: Jeff Layton <jlayton@kernel.org>
|
|
As there is precious little left in any DTS files referring to the
node "/chosen@0" as opposed to "/chosen", remove the two checks for
the former node name.
[paul.burton@mips.com:
The modified yamon-dt code only operates on
arch/mips/boot/dts/mti/sead3.dts right now, and that uses chosen
rather than chosen@0 anyway, so this should have no behavioural
effect.]
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20131/
Cc: linux-mips@linux-mips.org
|
|
ACP->SYSMEM DMA happens at every I2S->SYSMEM period
completion. Thus, there is delay of x frames till
I2S->SYSMEM reaches a period length. This delay is
communicated to user space.
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Give position on ACP->SYSMEM DMA channel for
the number of bytes that have been transferred on
the basis of current descriptor under service.
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In capture case we don't want ACP to SYSMEM dma
to be circular. This is because if an in place DSP
filter is applied to captured output then circular DMA
can overwrite the filter value with stale data.
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Return statements in functions returning bool should use true or false
instead of an integer value.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
|
|
Return statements in functions returning bool should use true or false
instead of an integer value.
This code was detected with the help of Coccinelle.
Acked-by: Roger Pau Monné <roger.pau@citrix.com>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Variables 'adv_set' and 'cp' are being assigned but are never used hence
they are redundant and can be removed.
Cleans up clang warnings:
net/bluetooth/hci_event.c:1135:29: warning: variable 'adv_set' set but not used [-Wunused-but-set-variable]
net/bluetooth/mgmt.c:3359:39: warning: variable 'cp' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
When the suballocator was unable to provide a suitable buffer for the MMUv1
linear window, we roll back the GPU initialization. As the GPU is runtime
resumed at that point we need to clear the kernel cmdbuf suballoc entry to
properly skip any attempt to manipulate the cmdbuf when the GPU gets shut
down in the runtime suspend later on.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
|
