summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2025-01-13ice: Fix ETH56G FC-FEC Rx offset valueKarol Kolacinski
Fix ETH56G FC-FEC incorrect Rx offset value by changing it from -255.96 to -469.26 ns. Those values are derived from HW spec and reflect internal delays. Hex value is a fixed point representation in Q23.9 format. Fixes: 7cab44f1c35f ("ice: Introduce ETH56G PHY model for E825C products") Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com> Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2025-01-13ice: Fix quad registers read on E825Karol Kolacinski
Quad registers are read/written incorrectly. E825 devices always use quad 0 address and differentiate between the PHYs by changing SBQ destination device (phy_0 or phy_0_peer). Add helpers for reading/writing PTP registers shared per quad and use correct quad address and SBQ destination device based on port. Fixes: 7cab44f1c35f ("ice: Introduce ETH56G PHY model for E825C products") Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com> Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com> Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2025-01-13ice: Fix E825 initializationKarol Kolacinski
Current implementation checks revision of all PHYs on all PFs, which is incorrect and may result in initialization failure. Check only the revision of the current PHY. Fixes: 7cab44f1c35f ("ice: Introduce ETH56G PHY model for E825C products") Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com> Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com> Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2025-01-13Merge tag 'md-6.14-20250113' of ↵Jens Axboe
https://git.kernel.org/pub/scm/linux/kernel/git/mdraid/linux into for-6.14/block Pull MD updates from Song: "1. Reintroduce md-linear, by Yu Kuai. 2. md-bitmap refactor and fix, by Yu Kuai. 3. Replace kmap_atomic with kmap_local_page, by David Reaver." * tag 'md-6.14-20250113' of https://git.kernel.org/pub/scm/linux/kernel/git/mdraid/linux: md/md-bitmap: move bitmap_{start, end}write to md upper layer md/raid5: implement pers->bitmap_sector() md: add a new callback pers->bitmap_sector() md/md-bitmap: remove the last parameter for bimtap_ops->endwrite() md/md-bitmap: factor behind write counters out from bitmap_{start/end}write() md: Replace deprecated kmap_atomic() with kmap_local_page() md: reintroduce md-linear
2025-01-13nvme: fix bogus kzalloc() return check in nvme_init_effects_log()Jens Axboe
nvme_init_effects_log() returns failure when kzalloc() is successful, which is obviously wrong and causes failures to boot. Correct the check. Fixes: d4a95adeabc6 ("nvme: Add error path for xa_store in nvme_init_effects") Signed-off-by: Jens Axboe <axboe@kernel.dk>
2025-01-13Merge tag 'mm-hotfixes-stable-2025-01-13-00-03' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm Pull misc fixes from Andrew Morton: "18 hotfixes. 11 are cc:stable. 13 are MM and 5 are non-MM. All patches are singletons - please see the relevant changelogs for details" * tag 'mm-hotfixes-stable-2025-01-13-00-03' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: fs/proc: fix softlockup in __read_vmcore (part 2) mm: fix assertion in folio_end_read() mm: vmscan : pgdemote vmstat is not getting updated when MGLRU is enabled. vmstat: disable vmstat_work on vmstat_cpu_down_prep() zram: fix potential UAF of zram table selftests/mm: set allocated memory to non-zero content in cow test mm: clear uffd-wp PTE/PMD state on mremap() module: fix writing of livepatch relocations in ROX text mm: zswap: properly synchronize freeing resources during CPU hotunplug Revert "mm: zswap: fix race between [de]compression and CPU hotunplug" hugetlb: fix NULL pointer dereference in trace_hugetlbfs_alloc_inode mm: fix div by zero in bdi_ratio_from_pages x86/execmem: fix ROX cache usage in Xen PV guests filemap: avoid truncating 64-bit offset to 32 bits tools: fix atomic_set() definition to set the value correctly mm/mempolicy: count MPOL_WEIGHTED_INTERLEAVE to "interleave_hit" scripts/decode_stacktrace.sh: fix decoding of lines with an additional info mm/kmemleak: fix percpu memory leak detection failure
2025-01-13Merge branch 'md-6.14-bitmap' into md-6.14Song Liu
Move bitmap_{start, end}write calls to md layer. These changes help address hangs in bitmap_startwrite([1],[2]). [1] https://lore.kernel.org/all/CAJpMwyjmHQLvm6zg1cmQErttNNQPDAAXPKM3xgTjMhbfts986Q@mail.gmail.com/ [2] https://lore.kernel.org/all/ADF7D720-5764-4AF3-B68E-1845988737AA@flyingcircus.io/ * md-6.14-bitmap: md/md-bitmap: move bitmap_{start, end}write to md upper layer md/raid5: implement pers->bitmap_sector() md: add a new callback pers->bitmap_sector() md/md-bitmap: remove the last parameter for bimtap_ops->endwrite() md/md-bitmap: factor behind write counters out from bitmap_{start/end}write()
2025-01-13md/md-bitmap: move bitmap_{start, end}write to md upper layerYu Kuai
There are two BUG reports that raid5 will hang at bitmap_startwrite([1],[2]), root cause is that bitmap start write and end write is unbalanced, it's not quite clear where, and while reviewing raid5 code, it's found that bitmap operations can be optimized. For example, for a 4 disks raid5, with chunksize=8k, if user issue a IO (0 + 48k) to the array: ┌────────────────────────────────────────────────────────────┐ │chunk 0 │ │ ┌────────────┬─────────────┬─────────────┬────────────┼ │ sh0 │A0: 0 + 4k │A1: 8k + 4k │A2: 16k + 4k │A3: P │ │ ┼────────────┼─────────────┼─────────────┼────────────┼ │ sh1 │B0: 4k + 4k │B1: 12k + 4k │B2: 20k + 4k │B3: P │ ┼──────┴────────────┴─────────────┴─────────────┴────────────┼ │chunk 1 │ │ ┌────────────┬─────────────┬─────────────┬────────────┤ │ sh2 │C0: 24k + 4k│C1: 32k + 4k │C2: P │C3: 40k + 4k│ │ ┼────────────┼─────────────┼─────────────┼────────────┼ │ sh3 │D0: 28k + 4k│D1: 36k + 4k │D2: P │D3: 44k + 4k│ └──────┴────────────┴─────────────┴─────────────┴────────────┘ Before this patch, 4 stripe head will be used, and each sh will attach bio for 3 disks, and each attached bio will trigger bitmap_startwrite() once, which means total 12 times. - 3 times (0 + 4k), for (A0, A1 and A2) - 3 times (4 + 4k), for (B0, B1 and B2) - 3 times (8 + 4k), for (C0, C1 and C3) - 3 times (12 + 4k), for (D0, D1 and D3) After this patch, md upper layer will calculate that IO range (0 + 48k) is corresponding to the bitmap (0 + 16k), and call bitmap_startwrite() just once. Noted that this patch will align bitmap ranges to the chunks, for example, if user issue a IO (0 + 4k) to array: - Before this patch, 1 time (0 + 4k), for A0; - After this patch, 1 time (0 + 8k) for chunk 0; Usually, one bitmap bit will represent more than one disk chunk, and this doesn't have any difference. And even if user really created a array that one chunk contain multiple bits, the overhead is that more data will be recovered after power failure. Also remove STRIPE_BITMAP_PENDING since it's not used anymore. [1] https://lore.kernel.org/all/CAJpMwyjmHQLvm6zg1cmQErttNNQPDAAXPKM3xgTjMhbfts986Q@mail.gmail.com/ [2] https://lore.kernel.org/all/ADF7D720-5764-4AF3-B68E-1845988737AA@flyingcircus.io/ Signed-off-by: Yu Kuai <yukuai3@huawei.com> Link: https://lore.kernel.org/r/20250109015145.158868-6-yukuai1@huaweicloud.com Signed-off-by: Song Liu <song@kernel.org>
2025-01-13md/raid5: implement pers->bitmap_sector()Yu Kuai
Bitmap is used for the whole array for raid1/raid10, hence IO for the array can be used directly for bitmap. However, bitmap is used for underlying disks for raid5, hence IO for the array can't be used directly for bitmap. Implement pers->bitmap_sector() for raid5 to convert IO ranges from the array to the underlying disks. Signed-off-by: Yu Kuai <yukuai3@huawei.com> Link: https://lore.kernel.org/r/20250109015145.158868-5-yukuai1@huaweicloud.com Signed-off-by: Song Liu <song@kernel.org>
2025-01-13md: add a new callback pers->bitmap_sector()Yu Kuai
This callback will be used in raid5 to convert io ranges from array to bitmap. Signed-off-by: Yu Kuai <yukuai3@huawei.com> Reviewed-by: Xiao Ni <xni@redhat.com> Link: https://lore.kernel.org/r/20250109015145.158868-4-yukuai1@huaweicloud.com Signed-off-by: Song Liu <song@kernel.org>
2025-01-13md/md-bitmap: remove the last parameter for bimtap_ops->endwrite()Yu Kuai
For the case that IO failed for one rdev, the bit will be mark as NEEDED in following cases: 1) If badblocks is set and rdev is not faulty; 2) If rdev is faulty; Case 1) is useless because synchronize data to badblocks make no sense. Case 2) can be replaced with mddev->degraded. Also remove R1BIO_Degraded, R10BIO_Degraded and STRIPE_DEGRADED since case 2) no longer use them. Signed-off-by: Yu Kuai <yukuai3@huawei.com> Link: https://lore.kernel.org/r/20250109015145.158868-3-yukuai1@huaweicloud.com Signed-off-by: Song Liu <song@kernel.org>
2025-01-13md/md-bitmap: factor behind write counters out from bitmap_{start/end}write()Yu Kuai
behind_write is only used in raid1, prepare to refactor bitmap_{start/end}write(), there are no functional changes. Signed-off-by: Yu Kuai <yukuai3@huawei.com> Reviewed-by: Xiao Ni <xni@redhat.com> Link: https://lore.kernel.org/r/20250109015145.158868-2-yukuai1@huaweicloud.com Signed-off-by: Song Liu <song@kernel.org>
2025-01-13Documentation: arm64: Remove stale and redundant virtual memory diagramsWill Deacon
The arm64 'memory.rst' file tries to document the virtual memory map and the translation procedure for a couple of kernel configurations. Unfortunately, the virtual memory map changes relatively frequently and we support considerably more configurations than we did when the docs were introduced (e.g. we now have support for 16KiB pages and 52-bit addressing). Furthermore, the Arm ARM is the definitive resource for the translation procedure and so there's little point in duplicating part of that information in the kernel documentation. Rather than continue trying (and failing) to maintain these diagrams, let's rip them out. The kernel page-table can be dumped using CONFIG_PTDUMP_DEBUGFS if necesssary. Link: https://lore.kernel.org/r/20250102065554.1533781-1-sangmoon.kim@samsung.com Reported-by: Sangmoon Kim <sangmoon.kim@samsung.com> Signed-off-by: Will Deacon <will@kernel.org>
2025-01-13vsnprintf: fix the number base for non-numeric formatsLinus Torvalds
Commit 8d4826cc8a8a ("vsnprintf: collapse the number format state into one single state") changed the format specification decoding to be a bit more straightforward but in the process ended up also resetting the number base to zero for formats that aren't clearly numerical. Now, the number base obviously doesn't matter for something like '%s', so this wasn't all that obvious. But some of our specialized pointer extension formatting (ie, things like "print out IPv6 address") did up depending on the default base-10 setting, and when they then tried to print out numbers in "base zero", things didn't work out so well. Most pointer formatting (including things like the default raw hex value conversion) didn't have this issue, because they used helpers that explicitly set the base. Reported-and-tested-by: kernel test robot <oliver.sang@intel.com> Closes: https://lore.kernel.org/oe-lkp/202501131352.e226f995-lkp@intel.com Fixes: 8d4826cc8a8a ("vsnprintf: collapse the number format state into one single state") Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2025-01-13md: Replace deprecated kmap_atomic() with kmap_local_page()David Reaver
kmap_atomic() is deprecated and should be replaced with kmap_local_page() [1][2]. kmap_local_page() is faster in kernels with HIGHMEM enabled, can take page faults, and allows preemption. According to [2], this is safe as long as the code between kmap_atomic() and kunmap_atomic() does not implicitly depend on disabling page faults or preemption. It appears to me that none of the call sites in this patch depend on disabling page faults or preemption; they are all mapping a page to simply extract some information from it or print some debug info. [1] https://lwn.net/Articles/836144/ [2] https://docs.kernel.org/mm/highmem.html#temporary-virtual-mappings Signed-off-by: David Reaver <me@davidreaver.com> Link: https://lore.kernel.org/r/20250108192131.46843-1-me@davidreaver.com Signed-off-by: Song Liu <song@kernel.org>
2025-01-13md: reintroduce md-linearYu Kuai
THe md-linear is removed by commit 849d18e27be9 ("md: Remove deprecated CONFIG_MD_LINEAR") because it has been marked as deprecated for a long time. However, md-linear is used widely for underlying disks with different size, sadly we didn't know this until now, and it's true useful to create partitions and assemble multiple raid and then append one to the other. People have to use dm-linear in this case now, however, they will prefer to minimize the number of involved modules. Fixes: 849d18e27be9 ("md: Remove deprecated CONFIG_MD_LINEAR") Cc: stable@vger.kernel.org Signed-off-by: Yu Kuai <yukuai3@huawei.com> Acked-by: Coly Li <colyli@kernel.org> Acked-by: Mike Snitzer <snitzer@kernel.org> Link: https://lore.kernel.org/r/20250102112841.1227111-1-yukuai1@huaweicloud.com Signed-off-by: Song Liu <song@kernel.org>
2025-01-13select: Fix unbalanced user_access_end()Christophe Leroy
While working on implementing user access validation on powerpc I got the following warnings on a pmac32_defconfig build: CC fs/select.o fs/select.o: warning: objtool: sys_pselect6+0x1bc: redundant UACCESS disable fs/select.o: warning: objtool: sys_pselect6_time32+0x1bc: redundant UACCESS disable On powerpc/32s, user_read_access_begin/end() are no-ops, but the failure path has a user_access_end() instead of user_read_access_end() which means an access end without any prior access begin. Replace that user_access_end() by user_read_access_end(). Fixes: 7e71609f64ec ("pselect6() and friends: take handling the combined 6th/7th args into helper") Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu> Link: https://lore.kernel.org/r/a7139e28d767a13e667ee3c79599a8047222ef36.1736751221.git.christophe.leroy@csgroup.eu Signed-off-by: Christian Brauner <brauner@kernel.org>
2025-01-13btrfs: remove the unused locked_folio parameter from ↵Qu Wenruo
btrfs_cleanup_ordered_extents() The function btrfs_cleanup_ordered_extents() is only called in error handling path, and the last caller with a @locked_folio parameter was removed to fix a bug in the btrfs_run_delalloc_range() error handling. There is no need to pass @locked_folio parameter anymore. Reviewed-by: Boris Burkov <boris@bur.io> Signed-off-by: Qu Wenruo <wqu@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
2025-01-13btrfs: add extra error messages for delalloc range related errorsQu Wenruo
All the error handling bugs I hit so far are all -ENOSPC from either: - cow_file_range() - run_delalloc_nocow() - submit_uncompressed_range() Previously when those functions failed, there was no error message at all, making the debugging much harder. So here we introduce extra error messages for: - cow_file_range() - run_delalloc_nocow() - submit_uncompressed_range() - writepage_delalloc() when btrfs_run_delalloc_range() failed - extent_writepage() when extent_writepage_io() failed One example of the new debug error messages is the following one: run fstests generic/750 at 2024-12-08 12:41:41 BTRFS: device fsid 461b25f5-e240-4543-8deb-e7c2bd01a6d3 devid 1 transid 8 /dev/mapper/test-scratch1 (253:4) scanned by mount (2436600) BTRFS info (device dm-4): first mount of filesystem 461b25f5-e240-4543-8deb-e7c2bd01a6d3 BTRFS info (device dm-4): using crc32c (crc32c-arm64) checksum algorithm BTRFS info (device dm-4): forcing free space tree for sector size 4096 with page size 65536 BTRFS info (device dm-4): using free-space-tree BTRFS warning (device dm-4): read-write for sector size 4096 with page size 65536 is experimental BTRFS info (device dm-4): checking UUID tree BTRFS error (device dm-4): cow_file_range failed, root=363 inode=412 start=503808 len=98304: -28 BTRFS error (device dm-4): run_delalloc_nocow failed, root=363 inode=412 start=503808 len=98304: -28 BTRFS error (device dm-4): failed to run delalloc range, root=363 ino=412 folio=458752 submit_bitmap=11-15 start=503808 len=98304: -28 Which shows an error from cow_file_range() which is called inside a nocow write attempt, along with the extra bitmap from writepage_delalloc(). Reviewed-by: Boris Burkov <boris@bur.io> Signed-off-by: Qu Wenruo <wqu@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
2025-01-13btrfs: subpage: dump the involved bitmap when ASSERT() failedQu Wenruo
For btrfs_folio_assert_not_dirty() and btrfs_folio_set_lock(), we call bitmap_test_range_all_zero() to ensure the involved range has no dirty/lock bit already set. However with my recent enhanced delalloc range error handling, I was hitting the ASSERT() inside btrfs_folio_set_lock(), and it turns out that some error handling path is not properly updating the folio flags. So add some extra dumping for the ASSERTs to dump the involved bitmap to help debug. Reviewed-by: Boris Burkov <boris@bur.io> Signed-off-by: Qu Wenruo <wqu@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
2025-01-13btrfs: subpage: fix the bitmap dump of the locked flagsQu Wenruo
We're dumping the locked bitmap into the @checked_bitmap variable, printing incorrect values during debug. Thankfully even during my development I haven't hit a case where I need to dump the locked bitmap. But for the sake of consistency, fix it by dupping the locked bitmap into @locked_bitmap variable for output. Fixes: 75258f20fb70 ("btrfs: subpage: dump extra subpage bitmaps for debug") Reviewed-by: Boris Burkov <boris@bur.io> Signed-off-by: Qu Wenruo <wqu@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
2025-01-13btrfs: do proper folio cleanup when run_delalloc_nocow() failedQu Wenruo
[BUG] With CONFIG_DEBUG_VM set, test case generic/476 has some chance to crash with the following VM_BUG_ON_FOLIO(): BTRFS error (device dm-3): cow_file_range failed, start 1146880 end 1253375 len 106496 ret -28 BTRFS error (device dm-3): run_delalloc_nocow failed, start 1146880 end 1253375 len 106496 ret -28 page: refcount:4 mapcount:0 mapping:00000000592787cc index:0x12 pfn:0x10664 aops:btrfs_aops [btrfs] ino:101 dentry name(?):"f1774" flags: 0x2fffff80004028(uptodate|lru|private|node=0|zone=2|lastcpupid=0xfffff) page dumped because: VM_BUG_ON_FOLIO(!folio_test_locked(folio)) ------------[ cut here ]------------ kernel BUG at mm/page-writeback.c:2992! Internal error: Oops - BUG: 00000000f2000800 [#1] SMP CPU: 2 UID: 0 PID: 3943513 Comm: kworker/u24:15 Tainted: G OE 6.12.0-rc7-custom+ #87 Tainted: [O]=OOT_MODULE, [E]=UNSIGNED_MODULE Hardware name: QEMU KVM Virtual Machine, BIOS unknown 2/2/2022 Workqueue: events_unbound btrfs_async_reclaim_data_space [btrfs] pc : folio_clear_dirty_for_io+0x128/0x258 lr : folio_clear_dirty_for_io+0x128/0x258 Call trace: folio_clear_dirty_for_io+0x128/0x258 btrfs_folio_clamp_clear_dirty+0x80/0xd0 [btrfs] __process_folios_contig+0x154/0x268 [btrfs] extent_clear_unlock_delalloc+0x5c/0x80 [btrfs] run_delalloc_nocow+0x5f8/0x760 [btrfs] btrfs_run_delalloc_range+0xa8/0x220 [btrfs] writepage_delalloc+0x230/0x4c8 [btrfs] extent_writepage+0xb8/0x358 [btrfs] extent_write_cache_pages+0x21c/0x4e8 [btrfs] btrfs_writepages+0x94/0x150 [btrfs] do_writepages+0x74/0x190 filemap_fdatawrite_wbc+0x88/0xc8 start_delalloc_inodes+0x178/0x3a8 [btrfs] btrfs_start_delalloc_roots+0x174/0x280 [btrfs] shrink_delalloc+0x114/0x280 [btrfs] flush_space+0x250/0x2f8 [btrfs] btrfs_async_reclaim_data_space+0x180/0x228 [btrfs] process_one_work+0x164/0x408 worker_thread+0x25c/0x388 kthread+0x100/0x118 ret_from_fork+0x10/0x20 Code: 910a8021 a90363f7 a9046bf9 94012379 (d4210000) ---[ end trace 0000000000000000 ]--- [CAUSE] The first two lines of extra debug messages show the problem is caused by the error handling of run_delalloc_nocow(). E.g. we have the following dirtied range (4K blocksize 4K page size): 0 16K 32K |//////////////////////////////////////| | Pre-allocated | And the range [0, 16K) has a preallocated extent. - Enter run_delalloc_nocow() for range [0, 16K) Which found range [0, 16K) is preallocated, can do the proper NOCOW write. - Enter fallback_to_fow() for range [16K, 32K) Since the range [16K, 32K) is not backed by preallocated extent, we have to go COW. - cow_file_range() failed for range [16K, 32K) So cow_file_range() will do the clean up by clearing folio dirty, unlock the folios. Now the folios in range [16K, 32K) is unlocked. - Enter extent_clear_unlock_delalloc() from run_delalloc_nocow() Which is called with PAGE_START_WRITEBACK to start page writeback. But folios can only be marked writeback when it's properly locked, thus this triggered the VM_BUG_ON_FOLIO(). Furthermore there is another hidden but common bug that run_delalloc_nocow() is not clearing the folio dirty flags in its error handling path. This is the common bug shared between run_delalloc_nocow() and cow_file_range(). [FIX] - Clear folio dirty for range [@start, @cur_offset) Introduce a helper, cleanup_dirty_folios(), which will find and lock the folio in the range, clear the dirty flag and start/end the writeback, with the extra handling for the @locked_folio. - Introduce a helper to clear folio dirty, start and end writeback - Introduce a helper to record the last failed COW range end This is to trace which range we should skip, to avoid double unlocking. - Skip the failed COW range for the error handling CC: stable@vger.kernel.org Reviewed-by: Boris Burkov <boris@bur.io> Signed-off-by: Qu Wenruo <wqu@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
2025-01-13btrfs: do proper folio cleanup when cow_file_range() failedQu Wenruo
[BUG] When testing with COW fixup marked as BUG_ON() (this is involved with the new pin_user_pages*() change, which should not result new out-of-band dirty pages), I hit a crash triggered by the BUG_ON() from hitting COW fixup path. This BUG_ON() happens just after a failed btrfs_run_delalloc_range(): BTRFS error (device dm-2): failed to run delalloc range, root 348 ino 405 folio 65536 submit_bitmap 6-15 start 90112 len 106496: -28 ------------[ cut here ]------------ kernel BUG at fs/btrfs/extent_io.c:1444! Internal error: Oops - BUG: 00000000f2000800 [#1] SMP CPU: 0 UID: 0 PID: 434621 Comm: kworker/u24:8 Tainted: G OE 6.12.0-rc7-custom+ #86 Hardware name: QEMU KVM Virtual Machine, BIOS unknown 2/2/2022 Workqueue: events_unbound btrfs_async_reclaim_data_space [btrfs] pc : extent_writepage_io+0x2d4/0x308 [btrfs] lr : extent_writepage_io+0x2d4/0x308 [btrfs] Call trace: extent_writepage_io+0x2d4/0x308 [btrfs] extent_writepage+0x218/0x330 [btrfs] extent_write_cache_pages+0x1d4/0x4b0 [btrfs] btrfs_writepages+0x94/0x150 [btrfs] do_writepages+0x74/0x190 filemap_fdatawrite_wbc+0x88/0xc8 start_delalloc_inodes+0x180/0x3b0 [btrfs] btrfs_start_delalloc_roots+0x174/0x280 [btrfs] shrink_delalloc+0x114/0x280 [btrfs] flush_space+0x250/0x2f8 [btrfs] btrfs_async_reclaim_data_space+0x180/0x228 [btrfs] process_one_work+0x164/0x408 worker_thread+0x25c/0x388 kthread+0x100/0x118 ret_from_fork+0x10/0x20 Code: aa1403e1 9402f3ef aa1403e0 9402f36f (d4210000) ---[ end trace 0000000000000000 ]--- [CAUSE] That failure is mostly from cow_file_range(), where we can hit -ENOSPC. Although the -ENOSPC is already a bug related to our space reservation code, let's just focus on the error handling. For example, we have the following dirty range [0, 64K) of an inode, with 4K sector size and 4K page size: 0 16K 32K 48K 64K |///////////////////////////////////////| |#######################################| Where |///| means page are still dirty, and |###| means the extent io tree has EXTENT_DELALLOC flag. - Enter extent_writepage() for page 0 - Enter btrfs_run_delalloc_range() for range [0, 64K) - Enter cow_file_range() for range [0, 64K) - Function btrfs_reserve_extent() only reserved one 16K extent So we created extent map and ordered extent for range [0, 16K) 0 16K 32K 48K 64K |////////|//////////////////////////////| |<- OE ->|##############################| And range [0, 16K) has its delalloc flag cleared. But since we haven't yet submit any bio, involved 4 pages are still dirty. - Function btrfs_reserve_extent() returns with -ENOSPC Now we have to run error cleanup, which will clear all EXTENT_DELALLOC* flags and clear the dirty flags for the remaining ranges: 0 16K 32K 48K 64K |////////| | | | | Note that range [0, 16K) still has its pages dirty. - Some time later, writeback is triggered again for the range [0, 16K) since the page range still has dirty flags. - btrfs_run_delalloc_range() will do nothing because there is no EXTENT_DELALLOC flag. - extent_writepage_io() finds page 0 has no ordered flag Which falls into the COW fixup path, triggering the BUG_ON(). Unfortunately this error handling bug dates back to the introduction of btrfs. Thankfully with the abuse of COW fixup, at least it won't crash the kernel. [FIX] Instead of immediately unlocking the extent and folios, we keep the extent and folios locked until either erroring out or the whole delalloc range finished. When the whole delalloc range finished without error, we just unlock the whole range with PAGE_SET_ORDERED (and PAGE_UNLOCK for !keep_locked cases), with EXTENT_DELALLOC and EXTENT_LOCKED cleared. And the involved folios will be properly submitted, with their dirty flags cleared during submission. For the error path, it will be a little more complex: - The range with ordered extent allocated (range (1)) We only clear the EXTENT_DELALLOC and EXTENT_LOCKED, as the remaining flags are cleaned up by btrfs_mark_ordered_io_finished()->btrfs_finish_one_ordered(). For folios we finish the IO (clear dirty, start writeback and immediately finish the writeback) and unlock the folios. - The range with reserved extent but no ordered extent (range(2)) - The range we never touched (range(3)) For both range (2) and range(3) the behavior is not changed. Now even if cow_file_range() failed halfway with some successfully reserved extents/ordered extents, we will keep all folios clean, so there will be no future writeback triggered on them. CC: stable@vger.kernel.org Reviewed-by: Boris Burkov <boris@bur.io> Signed-off-by: Qu Wenruo <wqu@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
2025-01-13nouveau/fence: handle cross device fences properlyDave Airlie
The fence sync logic doesn't handle a fence sync across devices as it tries to write to a channel offset from one device into the fence bo from a different device, which won't work so well. This patch fixes that to avoid using the sync path in the case where the fences come from different nouveau drm devices. This works fine on a single device as the fence bo is shared across the devices, and mapped into each channels vma space, the channel offsets are therefore okay to pass between sides, so one channel can sync on the seqnos from the other by using the offset into it's vma. Signed-off-by: Dave Airlie <airlied@redhat.com> Cc: stable@vger.kernel.org Reviewed-by: Ben Skeggs <bskeggs@nvidia.com> [ Fix compilation issue; remove version log from commit messsage. - Danilo ] Signed-off-by: Danilo Krummrich <dakr@kernel.org> Link: https://patchwork.freedesktop.org/patch/msgid/20250109005553.623947-1-airlied@gmail.com
2025-01-13partitions: ldm: remove the initial kernel-doc notationRandy Dunlap
Remove the file's first comment describing what the file is. This comment is not in kernel-doc format so it causes a kernel-doc warning. ldm.h:13: warning: expecting prototype for ldm(). Prototype was for _FS_PT_LDM_H_() instead Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Richard Russon (FlatCap) <ldm@flatcap.org> Cc: linux-ntfs-dev@lists.sourceforge.net Cc: Jens Axboe <axboe@kernel.dk> Link: https://lore.kernel.org/r/20250111062758.910458-1-rdunlap@infradead.org Signed-off-by: Jens Axboe <axboe@kernel.dk>
2025-01-13blk-cgroup: rwstat: fix kernel-doc warnings in header fileRandy Dunlap
Correct the function parameters to eliminate kernel-doc warnings: blk-cgroup-rwstat.h:63: warning: Function parameter or struct member 'opf' not described in 'blkg_rwstat_add' blk-cgroup-rwstat.h:63: warning: Excess function parameter 'op' description in 'blkg_rwstat_add' blk-cgroup-rwstat.h:91: warning: Function parameter or struct member 'result' not described in 'blkg_rwstat_read' Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Tejun Heo <tj@kernel.org> Cc: Josef Bacik <josef@toxicpanda.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: cgroups@vger.kernel.org Link: https://lore.kernel.org/r/20250111062748.910442-1-rdunlap@infradead.org Signed-off-by: Jens Axboe <axboe@kernel.dk>
2025-01-13blk-cgroup: fix kernel-doc warnings in header fileRandy Dunlap
Correct the function parameters and function names to eliminate kernel-doc warnings: blk-cgroup.h:238: warning: Function parameter or struct member 'bio' not described in 'bio_issue_as_root_blkg' blk-cgroup.h:248: warning: bad line: blk-cgroup.h:279: warning: expecting prototype for blkg_to_pdata(). Prototype was for blkg_to_pd() instead blk-cgroup.h:296: warning: expecting prototype for pdata_to_blkg(). Prototype was for pd_to_blkg() instead Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Tejun Heo <tj@kernel.org> Cc: Josef Bacik <josef@toxicpanda.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: cgroups@vger.kernel.org Link: https://lore.kernel.org/r/20250111062736.910383-1-rdunlap@infradead.org Signed-off-by: Jens Axboe <axboe@kernel.dk>
2025-01-13nbd: fix partial sendingMing Lei
nbd driver sends request header and payload with multiple call of sock_sendmsg, and partial sending can't be avoided. However, nbd driver returns BLK_STS_RESOURCE to block core in this situation. This way causes one issue: request->tag may change in the next run of nbd_queue_rq(), but the original old tag has been sent as part of header cookie, this way confuses nbd driver reply handling, since the real request can't be retrieved any more with the obsolete old tag. Fix it by retrying sending directly in per-socket work function, meantime return BLK_STS_OK to block layer core. Cc: vincent.chen@sifive.com Cc: Leon Schuermann <leon@is.currently.online> Cc: Bart Van Assche <bvanassche@acm.org> Reported-by: Kevin Wolf <kwolf@redhat.com> Signed-off-by: Ming Lei <ming.lei@redhat.com> Tested-by: Kevin Wolf <kwolf@redhat.com> Reviewed-by: Kevin Wolf <kwolf@redhat.com> Link: https://lore.kernel.org/r/20241029011941.153037-1-ming.lei@redhat.com Signed-off-by: Jens Axboe <axboe@kernel.dk>
2025-01-13block: mark GFP_NOIO around sysfs ->store()Ming Lei
sysfs ->store is called with queue freezed, meantime we have several ->store() callbacks(update_nr_requests, wbt, scheduler) to allocate memory with GFP_KERNEL which may run into direct reclaim code path, then potential deadlock can be caused. Fix the issue by marking NOIO around sysfs ->store() Reported-by: Thomas Hellström <thomas.hellstrom@linux.intel.com> Cc: stable@vger.kernel.org Signed-off-by: Ming Lei <ming.lei@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: John Garry <john.g.garry@oracle.com> Link: https://lore.kernel.org/r/20250113015833.698458-1-ming.lei@redhat.com Link: https://lore.kernel.org/linux-block/Z4RkemI9f6N5zoEF@fedora/T/#mc774c65eeca5c024d29695f9ac6152b87763f305 Signed-off-by: Jens Axboe <axboe@kernel.dk>
2025-01-13btrfs: fix error handling of submit_uncompressed_range()Qu Wenruo
[BUG] If we failed to compress the range, or cannot reserve a large enough data extent (e.g. too fragmented free space), we will fall back to submit_uncompressed_range(). But inside submit_uncompressed_range(), run_delalloc_cow() can also fail due to -ENOSPC or any other error. In that case there are 3 bugs in the error handling: 1) Double freeing for the same ordered extent This can lead to crash due to ordered extent double accounting 2) Start/end writeback without updating the subpage writeback bitmap 3) Unlock the folio without clear the subpage lock bitmap Both bugs 2) and 3) will crash the kernel if the btrfs block size is smaller than folio size, as the next time the folio gets writeback/lock updates, subpage will find the bitmap already have the range set, triggering an ASSERT(). [CAUSE] Bug 1) happens in the following call chain: submit_uncompressed_range() |- run_delalloc_cow() | |- cow_file_range() | |- btrfs_reserve_extent() | Failed with -ENOSPC or whatever error | |- btrfs_clean_up_ordered_extents() | |- btrfs_mark_ordered_io_finished() | Which cleans all the ordered extents in the async_extent range. | |- btrfs_mark_ordered_io_finished() Which cleans the folio range. The finished ordered extents may not be immediately removed from the ordered io tree, as they are removed inside a work queue. So the second btrfs_mark_ordered_io_finished() may find the finished but not-yet-removed ordered extents, and double free them. Furthermore, the second btrfs_mark_ordered_io_finished() is not subpage compatible, as it uses fixed folio_pos() with PAGE_SIZE, which can cover other ordered extents. Bugs 2) and 3) are more straightforward, btrfs just calls folio_unlock(), folio_start_writeback() and folio_end_writeback(), other than the helpers which handle subpage cases. [FIX] For bug 1) since the first btrfs_cleanup_ordered_extents() call is handling the whole range, we should not do the second btrfs_mark_ordered_io_finished() call. And for the first btrfs_cleanup_ordered_extents(), we no longer need to pass the @locked_page parameter, as we are already in the async extent context, thus will never rely on the error handling inside btrfs_run_delalloc_range(). So just let the btrfs_clean_up_ordered_extents() handle every folio equally. For bug 2) we should not even call folio_start_writeback()/folio_end_writeback() anymore. As the error handling protocol, cow_file_range() should clear dirty flag and start/finish the writeback for the whole range passed in. For bug 3) just change the folio_unlock() to btrfs_folio_end_lock() helper. Reviewed-by: Boris Burkov <boris@bur.io> Signed-off-by: Qu Wenruo <wqu@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
2025-01-13btrfs: fix double accounting race when extent_writepage_io() failedQu Wenruo
[BUG] If submit_one_sector() failed inside extent_writepage_io() for sector size < page size cases (e.g. 4K sector size and 64K page size), then we can hit double ordered extent accounting error. This should be very rare, as submit_one_sector() only fails when we failed to grab the extent map, and such extent map should exist inside the memory and has been pinned. [CAUSE] For example we have the following folio layout: 0 4K 32K 48K 60K 64K |//| |//////| |///| Where |///| is the dirty range we need to writeback. The 3 different dirty ranges are submitted for regular COW. Now we hit the following sequence: - submit_one_sector() returned 0 for [0, 4K) - submit_one_sector() returned 0 for [32K, 48K) - submit_one_sector() returned error for [60K, 64K) - btrfs_mark_ordered_io_finished() called for the whole folio This will mark the following ranges as finished: * [0, 4K) * [32K, 48K) Both ranges have their IO already submitted, this cleanup will lead to double accounting. * [60K, 64K) That's the correct cleanup. The only good news is, this error is only theoretical, as the target extent map is always pinned, thus we should directly grab it from memory, other than reading it from the disk. [FIX] Instead of calling btrfs_mark_ordered_io_finished() for the whole folio range, which can touch ranges we should not touch, instead move the error handling inside extent_writepage_io(). So that we can cleanup exact sectors that ought to be submitted but failed. This provides much more accurate cleanup, avoiding the double accounting. CC: stable@vger.kernel.org # 5.15+ Signed-off-by: Qu Wenruo <wqu@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
2025-01-13btrfs: fix double accounting race when btrfs_run_delalloc_range() failedQu Wenruo
[BUG] When running btrfs with block size (4K) smaller than page size (64K, aarch64), there is a very high chance to crash the kernel at generic/750, with the following messages: (before the call traces, there are 3 extra debug messages added) BTRFS warning (device dm-3): read-write for sector size 4096 with page size 65536 is experimental BTRFS info (device dm-3): checking UUID tree hrtimer: interrupt took 5451385 ns BTRFS error (device dm-3): cow_file_range failed, root=4957 inode=257 start=1605632 len=69632: -28 BTRFS error (device dm-3): run_delalloc_nocow failed, root=4957 inode=257 start=1605632 len=69632: -28 BTRFS error (device dm-3): failed to run delalloc range, root=4957 ino=257 folio=1572864 submit_bitmap=8-15 start=1605632 len=69632: -28 ------------[ cut here ]------------ WARNING: CPU: 2 PID: 3020984 at ordered-data.c:360 can_finish_ordered_extent+0x370/0x3b8 [btrfs] CPU: 2 UID: 0 PID: 3020984 Comm: kworker/u24:1 Tainted: G OE 6.13.0-rc1-custom+ #89 Tainted: [O]=OOT_MODULE, [E]=UNSIGNED_MODULE Hardware name: QEMU KVM Virtual Machine, BIOS unknown 2/2/2022 Workqueue: events_unbound btrfs_async_reclaim_data_space [btrfs] pc : can_finish_ordered_extent+0x370/0x3b8 [btrfs] lr : can_finish_ordered_extent+0x1ec/0x3b8 [btrfs] Call trace: can_finish_ordered_extent+0x370/0x3b8 [btrfs] (P) can_finish_ordered_extent+0x1ec/0x3b8 [btrfs] (L) btrfs_mark_ordered_io_finished+0x130/0x2b8 [btrfs] extent_writepage+0x10c/0x3b8 [btrfs] extent_write_cache_pages+0x21c/0x4e8 [btrfs] btrfs_writepages+0x94/0x160 [btrfs] do_writepages+0x74/0x190 filemap_fdatawrite_wbc+0x74/0xa0 start_delalloc_inodes+0x17c/0x3b0 [btrfs] btrfs_start_delalloc_roots+0x17c/0x288 [btrfs] shrink_delalloc+0x11c/0x280 [btrfs] flush_space+0x288/0x328 [btrfs] btrfs_async_reclaim_data_space+0x180/0x228 [btrfs] process_one_work+0x228/0x680 worker_thread+0x1bc/0x360 kthread+0x100/0x118 ret_from_fork+0x10/0x20 ---[ end trace 0000000000000000 ]--- BTRFS critical (device dm-3): bad ordered extent accounting, root=4957 ino=257 OE offset=1605632 OE len=16384 to_dec=16384 left=0 BTRFS critical (device dm-3): bad ordered extent accounting, root=4957 ino=257 OE offset=1622016 OE len=12288 to_dec=12288 left=0 Unable to handle kernel NULL pointer dereference at virtual address 0000000000000008 BTRFS critical (device dm-3): bad ordered extent accounting, root=4957 ino=257 OE offset=1634304 OE len=8192 to_dec=4096 left=0 CPU: 1 UID: 0 PID: 3286940 Comm: kworker/u24:3 Tainted: G W OE 6.13.0-rc1-custom+ #89 Hardware name: QEMU KVM Virtual Machine, BIOS unknown 2/2/2022 Workqueue: btrfs_work_helper [btrfs] (btrfs-endio-write) pstate: 404000c5 (nZcv daIF +PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : process_one_work+0x110/0x680 lr : worker_thread+0x1bc/0x360 Call trace: process_one_work+0x110/0x680 (P) worker_thread+0x1bc/0x360 (L) worker_thread+0x1bc/0x360 kthread+0x100/0x118 ret_from_fork+0x10/0x20 Code: f84086a1 f9000fe1 53041c21 b9003361 (f9400661) ---[ end trace 0000000000000000 ]--- Kernel panic - not syncing: Oops: Fatal exception SMP: stopping secondary CPUs SMP: failed to stop secondary CPUs 2-3 Dumping ftrace buffer: (ftrace buffer empty) Kernel Offset: 0x275bb9540000 from 0xffff800080000000 PHYS_OFFSET: 0xffff8fbba0000000 CPU features: 0x100,00000070,00801250,8201720b [CAUSE] The above warning is triggered immediately after the delalloc range failure, this happens in the following sequence: - Range [1568K, 1636K) is dirty 1536K 1568K 1600K 1636K 1664K | |/////////|////////| | Where 1536K, 1600K and 1664K are page boundaries (64K page size) - Enter extent_writepage() for page 1536K - Enter run_delalloc_nocow() with locked page 1536K and range [1568K, 1636K) This is due to the inode having preallocated extents. - Enter cow_file_range() with locked page 1536K and range [1568K, 1636K) - btrfs_reserve_extent() only reserved two extents The main loop of cow_file_range() only reserved two data extents, Now we have: 1536K 1568K 1600K 1636K 1664K | |<-->|<--->|/|///////| | 1584K 1596K Range [1568K, 1596K) has an ordered extent reserved. - btrfs_reserve_extent() failed inside cow_file_range() for file offset 1596K This is already a bug in our space reservation code, but for now let's focus on the error handling path. Now cow_file_range() returned -ENOSPC. - btrfs_run_delalloc_range() do error cleanup <<< ROOT CAUSE Call btrfs_cleanup_ordered_extents() with locked folio 1536K and range [1568K, 1636K) Function btrfs_cleanup_ordered_extents() normally needs to skip the ranges inside the folio, as it will normally be cleaned up by extent_writepage(). Such split error handling is already problematic in the first place. What's worse is the folio range skipping itself, which is not taking subpage cases into consideration at all, it will only skip the range if the page start >= the range start. In our case, the page start < the range start, since for subpage cases we can have delalloc ranges inside the folio but not covering the folio. So it doesn't skip the page range at all. This means all the ordered extents, both [1568K, 1584K) and [1584K, 1596K) will be marked as IOERR. And these two ordered extents have no more pending ios, they are marked finished, and *QUEUED* to be deleted from the io tree. - extent_writepage() do error cleanup Call btrfs_mark_ordered_io_finished() for the range [1536K, 1600K). Although ranges [1568K, 1584K) and [1584K, 1596K) are finished, the deletion from io tree is async, it may or may not happen at this time. If the ranges have not yet been removed, we will do double cleaning on those ranges, triggering the above ordered extent warnings. In theory there are other bugs, like the cleanup in extent_writepage() can cause double accounting on ranges that are submitted asynchronously (compression for example). But that's much harder to trigger because normally we do not mix regular and compression delalloc ranges. [FIX] The folio range split is already buggy and not subpage compatible, it was introduced a long time ago where subpage support was not even considered. So instead of splitting the ordered extents cleanup into the folio range and out of folio range, do all the cleanup inside writepage_delalloc(). - Pass @NULL as locked_folio for btrfs_cleanup_ordered_extents() in btrfs_run_delalloc_range() - Skip the btrfs_cleanup_ordered_extents() if writepage_delalloc() failed So all ordered extents are only cleaned up by btrfs_run_delalloc_range(). - Handle the ranges that already have ordered extents allocated If part of the folio already has ordered extent allocated, and btrfs_run_delalloc_range() failed, we also need to cleanup that range. Now we have a concentrated error handling for ordered extents during btrfs_run_delalloc_range(). Fixes: d1051d6ebf8e ("btrfs: Fix error handling in btrfs_cleanup_ordered_extents") CC: stable@vger.kernel.org # 5.15+ Reviewed-by: Boris Burkov <boris@bur.io> Signed-off-by: Qu Wenruo <wqu@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
2025-01-13Merge tag 'nvme-6.14-2025-01-12' of git://git.infradead.org/nvme into ↵Jens Axboe
for-6.14/block Pull NVMe updates from Keith: "nvme updates for Linux 6.14 - Target support for PCI-Endpoint transport (Damien) - TCP IO queue spreading fixes (Sagi, Chaitanya) - Target handling for "limited retry" flags (Guixen) - Poll type fix (Yongsoo) - Xarray storage error handling (Keisuke) - Host memory buffer free size fix on error (Francis)" * tag 'nvme-6.14-2025-01-12' of git://git.infradead.org/nvme: (25 commits) nvme-pci: use correct size to free the hmb buffer nvme: Add error path for xa_store in nvme_init_effects nvme-pci: fix comment typo Documentation: Document the NVMe PCI endpoint target driver nvmet: New NVMe PCI endpoint function target driver nvmet: Implement arbitration feature support nvmet: Implement interrupt config feature support nvmet: Implement interrupt coalescing feature support nvmet: Implement host identifier set feature support nvmet: Introduce get/set_feature controller operations nvmet: Do not require SGL for PCI target controller commands nvmet: Add support for I/O queue management admin commands nvmet: Introduce nvmet_sq_create() and nvmet_cq_create() nvmet: Introduce nvmet_req_transfer_len() nvmet: Improve nvmet_alloc_ctrl() interface and implementation nvme: Add PCI transport type nvmet: Add drvdata field to struct nvmet_ctrl nvmet: Introduce nvmet_get_cmd_effects_admin() nvmet: Export nvmet_update_cc() and nvmet_cc_xxx() helpers nvmet: Add vendor_id and subsys_vendor_id subsystem attributes ...
2025-01-13btrfs: async-thread: rename DFT_THRESHOLD to DEFAULT_THRESHOLDDavid Sterba
Rename the macro so it's obvious what it means. Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Reviewed-by: Anand Jain <anand.jain@oracle.com> Signed-off-by: David Sterba <dsterba@suse.com>
2025-01-13btrfs: remove redundant variables from __process_folios_contig() and ↵David Sterba
lock_delalloc_folios() Same pattern in both functions, we really only use index, start_index is redundant. Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Reviewed-by: Anand Jain <anand.jain@oracle.com> Signed-off-by: David Sterba <dsterba@suse.com>
2025-01-13btrfs: split waiting from read_extent_buffer_pages(), drop parameter waitDavid Sterba
There are only 2 WAIT_* values left for wait parameter, we can encode this to the function name if the waiting functionality is split. Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Reviewed-by: Anand Jain <anand.jain@oracle.com> Signed-off-by: David Sterba <dsterba@suse.com>
2025-01-13btrfs: remove unused define WAIT_PAGE_LOCK for extent ioDavid Sterba
Last use was in the readahead code that got removed by f26c9238602856 ("btrfs: remove reada infrastructure"). Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Reviewed-by: Anand Jain <anand.jain@oracle.com> Signed-off-by: David Sterba <dsterba@suse.com>
2025-01-13btrfs: unwrap folio locking helpersDavid Sterba
Another conversion to folio API, use the folio locking directly instead of back and forth page <-> folio conversions. Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Reviewed-by: Anand Jain <anand.jain@oracle.com> Signed-off-by: David Sterba <dsterba@suse.com>
2025-01-13btrfs: change return type to bool type of check_eb_alignment()David Sterba
The check function pattern is supposed to return true/false, currently there's only one error code. Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Reviewed-by: Anand Jain <anand.jain@oracle.com> Signed-off-by: David Sterba <dsterba@suse.com>
2025-01-13btrfs: switch grab_extent_buffer() to foliosDavid Sterba
Use the folio API, remove page_folio/folio_page conversions. Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Reviewed-by: Anand Jain <anand.jain@oracle.com> Signed-off-by: David Sterba <dsterba@suse.com>
2025-01-13btrfs: rename btrfs_release_extent_buffer_pages() to mention foliosDavid Sterba
Continue page to folio updates, sync what the function does with it's name. Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Reviewed-by: Anand Jain <anand.jain@oracle.com> Signed-off-by: David Sterba <dsterba@suse.com>
2025-01-13btrfs: open code __free_extent_buffer()David Sterba
Using the kmem cache freeing directly is clear enough, we don't need to wrap it. All the users are in the same file. Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Reviewed-by: Anand Jain <anand.jain@oracle.com> Signed-off-by: David Sterba <dsterba@suse.com>
2025-01-13btrfs: drop one time used local variable in end_bbio_meta_write()David Sterba
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Reviewed-by: Anand Jain <anand.jain@oracle.com> Signed-off-by: David Sterba <dsterba@suse.com>
2025-01-13btrfs: make wait_on_extent_buffer_writeback() static inlineDavid Sterba
The simple helper can be inlined, no need for the separate function. Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Reviewed-by: Anand Jain <anand.jain@oracle.com> Signed-off-by: David Sterba <dsterba@suse.com>
2025-01-13btrfs: use btrfs_inode in extent_writepage()David Sterba
As extent_writepage() is internal helper we should use our inode type, so change it from struct inode. Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Reviewed-by: Anand Jain <anand.jain@oracle.com> Signed-off-by: David Sterba <dsterba@suse.com>
2025-01-13btrfs: rename __get_extent_map() and pass btrfs_inodeDavid Sterba
The double underscore naming scheme does not apply here, there's only only get_extent_map(). As the definition is changed also pass the struct btrfs_inode. Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Reviewed-by: Anand Jain <anand.jain@oracle.com> Signed-off-by: David Sterba <dsterba@suse.com>
2025-01-13btrfs: open code set_page_extent_mapped()David Sterba
The function set_page_extent_mapped() is now a simple wrapper so use the folio helper. Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Reviewed-by: Anand Jain <anand.jain@oracle.com> Signed-off-by: David Sterba <dsterba@suse.com>
2025-01-13btrfs: rename __unlock_for_delalloc() and drop underscoresDavid Sterba
Drop the leading underscores in '__unlock_for_delalloc()' and rename it to 'unlock_delalloc_folio()'. This also ensures naming parity with 'lock_delalloc_folios()'. Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Reviewed-by: Anand Jain <anand.jain@oracle.com> Signed-off-by: David Sterba <dsterba@suse.com>
2025-01-13btrfs: use SECTOR_SIZE defines in btrfs_issue_discard()David Sterba
Use the existing define for single sector size. Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Reviewed-by: Anand Jain <anand.jain@oracle.com> Signed-off-by: David Sterba <dsterba@suse.com>
2025-01-13btrfs: remove stray comment about SRCUDavid Sterba
The subvol_srcu was removed in c75e839414d361 ("btrfs: kill the subvol_srcu") years ago. Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Reviewed-by: Anand Jain <anand.jain@oracle.com> Signed-off-by: David Sterba <dsterba@suse.com>
generated by cgit (git 2.34.1) at 2025-09-13 15:41:03 +0000