| Age | Commit message (Collapse) | Author |
|---|
|
Instead of duplicating the SECTOR_SHIFT definition from <linux/blkdev.h>,
use it. This patch does not change any functionality.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Commit 057085e522f8 ("target: Fix race for SCF_COMPARE_AND_WRITE_POST
checking") removed the code that checks the SCF_COMPARE_AND_WRITE_POST
flag. Hence also remove the flag itself.
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
A value is assigned to the xcopy_op member of struct xcopy_pt_cmd but
that value is never used. Hence remove the xcopy_op member.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Change one occurrence of "aleady" into "already" and one occurrence of
"is" into "if".
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
On GENETv5, there is a hardware issue which prevents the GENET hardware
from generating a link UP interrupt when the link is operating at
10Mbits/sec. Since we do not have any way to configure the link
detection logic, fallback to polling in that case.
Fixes: 421380856d9c ("net: bcmgenet: add support for the GENETv5 hardware")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
net/rxrpc/output.c: In function 'rxrpc_reject_packets':
net/rxrpc/output.c:527:11: warning:
variable 'ioc' set but not used [-Wunused-but-set-variable]
'ioc' is the correct kvec num when sending a BUSY (or an ABORT) response
packet.
Fixes: ece64fec164f ("rxrpc: Emit BUSY packets when supposed to rather than ABORTs")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix an uninitialised variable introduced by the last patch. This can cause
a crash when a new call comes in to a local service, such as when an AFS
fileserver calls back to the local cache manager.
Fixes: c1e15b4944c9 ("rxrpc: Fix the packet reception routine")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Heiner Kallweit says:
====================
net: phy: improve and simplify state machine
Improve / simplify handling of states PHY_RUNNING and PHY_RESUMING in
phylib state machine.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simplify code for handling state PHY_RESUMING, no functional change
intended.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Handling of state PHY_RUNNING seems to be more complex than it needs
to be. If not polling, then we don't have to do anything, we'll
receive an interrupt and go to state PHY_CHANGELINK once the link
goes down. If polling and link is down, we don't have to go the
extra mile over PHY_CHANGELINK and call phy_read_status() again
but can set status PHY_NOLINK directly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the commit referred to below we added link tolerance as an additional
criteria for declaring broadcast transmission "stale" and resetting the
unicast links to the affected node.
Unfortunately, this 'improvement' introduced two bugs, which each and
one alone cause only limited problems, but combined lead to seemingly
stochastic unicast link resets, depending on the amount of broadcast
traffic transmitted.
The first issue, a missing initialization of the 'tolerance' field of
the receiver broadcast link, was recently fixed by commit 047491ea334a
("tipc: set link tolerance correctly in broadcast link").
Ths second issue, where we omit to reset the 'stale_cnt' field of
the same link after a 'stale' period is over, leads to this counter
accumulating over time, and in the absence of the 'tolerance' criteria
leads to the above described symptoms. This commit adds the missing
initialization.
Fixes: a4dc70d46cf1 ("tipc: extend link reset criteria for stale packet retransmission")
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This makes use of NTF_USE in vxlan driver consistent
with bridge driver.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
WHen an llc sock is added into the sk_laddr_hash of an llc_sap,
it is not marked with SOCK_RCU_FREE.
This causes that the sock could be freed while it is still being
read by __llc_lookup_established() with RCU read lock. sock is
refcounted, but with RCU read lock, nothing prevents the readers
getting a zero refcnt.
Fix it by setting SOCK_RCU_FREE in llc_sap_add_socket().
Reported-by: syzbot+11e05f04c15e03be5254@syzkaller.appspotmail.com
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
command
The new command (NCSI_CMD_SEND_CMD) is added to allow user space application
to send NC-SI command to the network card.
Also, add a new attribute (NCSI_ATTR_DATA) for transferring request and response.
The work flow is as below.
Request:
User space application
-> Netlink interface (msg)
-> new Netlink handler - ncsi_send_cmd_nl()
-> ncsi_xmit_cmd()
Response:
Response received - ncsi_rcv_rsp()
-> internal response handler - ncsi_rsp_handler_xxx()
-> ncsi_rsp_handler_netlink()
-> ncsi_send_netlink_rsp ()
-> Netlink interface (msg)
-> user space application
Command timeout - ncsi_request_timeout()
-> ncsi_send_netlink_timeout ()
-> Netlink interface (msg with zero data length)
-> user space application
Error:
Error detected
-> ncsi_send_netlink_err ()
-> Netlink interface (err msg)
-> user space application
Signed-off-by: Justin Lee <justin.lee1@dell.com>
Reviewed-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When starting the state machine there may be work to be done
immediately, e.g. if the initial state is PHY_UP then the state
machine may trigger an autonegotiation. Having said that I see no need
to wait a second until the state machine is run first time.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Toshiaki Makita says:
====================
veth: XDP stats improvement
ndo_xdp_xmit in veth did not update packet counters as described in [1].
Also, current implementation only updates counters on tx side so rx side
events like XDP_DROP were not collected.
This series implements the missing accounting as well as support for
ethtool per-queue stats in veth.
Patch 1: Update drop counter in ndo_xdp_xmit.
Patch 2: Update packet and byte counters for all XDP path, and drop
counter on XDP_DROP.
Patch 3: Support per-queue ethtool stats for XDP counters.
Note that counters are maintained on per-queue basis for XDP but not
otherwise (per-cpu and atomic as before). This is because 1) tx path in
veth is essentially lockless so we cannot update per-queue stats on tx,
and 2) rx path is net core routine (process_backlog) which cannot update
per-queue based stats when XDP is disabled. On the other hand there are
real rxqs and napi handlers for veth XDP, so update per-queue stats on
rx for XDP packets, and use them to calculate tx counters as well,
contrary to the existing non-XDP counters.
[1] https://patchwork.ozlabs.org/cover/953071/#1967449
====================
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Expose per-queue stats for ethtool -S.
As there are only rx queues, and rx queues are used only when XDP is
used, per-queue counters are only rx XDP ones.
Example:
$ ethtool -S veth0
NIC statistics:
peer_ifindex: 11
rx_queue_0_xdp_packets: 28601434
rx_queue_0_xdp_bytes: 1716086040
rx_queue_0_xdp_drops: 28601434
rx_queue_1_xdp_packets: 17873050
rx_queue_1_xdp_bytes: 1072383000
rx_queue_1_xdp_drops: 17873050
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On XDP path veth has napi handler so we can collect statistics on
per-queue basis for XDP.
By this change now we can collect XDP_DROP drop count as well as packets
and bytes coming through ndo_xdp_xmit. Packet counters shown by
"ip -s link", sysfs stats or /proc/net/dev is now correct for XDP.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use existing atomic drop counter. Since drop path is really an
exceptional case here, I'm thinking atomic ops would not hurt the
performance.
XDP packets and bytes are not counted in ndo_xdp_xmit, but will be
accounted on rx side by the following commit.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
INADDR_ANY is hard-coded when activating UDP bearer. So, we could not
bind to a specific IP address even with replicast mode using - given
remote ip address instead of using multicast ip address.
In this commit, we fixed it by checking and switch to use appropriate
local ip address.
before:
$netstat -plu
Active Internet connections (only servers)
Proto Recv-Q Send-Q Local Address Foreign Address
udp 0 0 **0.0.0.0:6118** 0.0.0.0:*
after:
$netstat -plu
Active Internet connections (only servers)
Proto Recv-Q Send-Q Local Address Foreign Address
udp 0 0 **10.0.0.2:6118** 0.0.0.0:*
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2018-10-10
This pull request includes some fixes to mlx5 driver,
Please pull and let me know if there's any problem.
For -stable v4.11:
('net/mlx5: Take only bit 24-26 of wqe.pftype_wq for page fault type')
For -stable v4.17:
('net/mlx5: Fix memory leak when setting fpga ipsec caps')
For -stable v4.18:
('net/mlx5: WQ, fixes for fragmented WQ buffers API')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5e-updates-2018-10-10
IPoIB netlink support and mlx5e pre-allocated netdevice initialization
IP link was broken due to the changes in IPoIB for the rdma_netdev
support after commit cd565b4b51e5
("IB/IPoIB: Support acceleration options callbacks").
This patchset fixes IPoIB pkey creation and removal using rtnetlink by
adding support in both IPoIB ULP layer and mlx5 layer:
From Jason and Denis:
1) Introduces changes in the RDMA netdev code in order to
allow allocation of the netdev to be done by the rtnl netdev code.
2) Reworks IPoIB initialization to use the two step rdma_netdev
creation.
From Feras and Saeed, mlx5e netdev layer refactoring to allow accepting
pre-allocated netdevs:
3) Adds support to initialize/cleanup netdevs that are not created
by mlx5 driver.
4) Change mlx5e netdevice layer to accept the pre-allocated netdevice
queue number.
5) Initialize mlx5e generic structures in one place to be used for all
netdevs types NIC/representors/IPoIB (both mlx5 allocated and
pre-allocted).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Similarly to what has been done in 8b4c3cdd9dd8 ("net: sched: Add policy
validation for tc attributes"), fix classifier code to add validation of
TCA_CHAIN and TCA_KIND netlink attributes.
tested with:
# ./tdc.py -c filter
v2: Let sch_api and cls_api share nla_policy they have in common, thanks
to David Ahern.
v3: Avoid EXPORT_SYMBOL(), as validation of those attributes is not done
by TC modules, thanks to Cong Wang.
While at it, restore the 'Delete / get qdisc' comment to its orginal
position, just above tc_get_qdisc() function prototype.
Fixes: 5bc1701881e39 ("net: sched: introduce multichain support for filters")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Maciej W. Rozycki says:
====================
FDDI: DEC FDDIcontroller 700 TURBOchannel adapter support
This is an update to <http://patchwork.ozlabs.org/patch/342737/>. I
believe I have addressed all the requests made in the previous review
round.
There is still one `checkpatch.pl' warning remaining:
WARNING: quoted string split across lines
+ pr_info("%s: ROM rev. %.4s, firmware rev. %.4s, RMC rev. %.4s, "
+ "SMT ver. %u\n", fp->name, rom_rev, fw_rev, rmc_rev, smt_ver);
total: 0 errors, 1 warnings, 2458 lines checked
however I think the value of staying within 80 columns is higher than the
value of having the string on a single line. This is because with all the
formatting specifiers there it is not directly greppable based on the
final output produced to the kernel log on one hand, e.g.:
tc2: ROM rev. 1.0, firmware rev. 1.2, RMC rev. A, SMT ver. 1
while it can be easily tracked down by grepping for an obvious substring
such as "RMC rev" on the other.
The issue with MMIO barriers I discussed in the course of the original
review turned out mostly irrelevant to this driver, because as I have
learnt in a recent Alpha/Linux discussion starting here:
<https://marc.info/?i=alpine.LRH.2.02.1808161556450.13597%20()%20file01%20!%20intranet%20!%20prod%20!%20int%20!%20rdu2%20!%20redhat%20!%20com>
our MMIO API mandates the `readX' and `writeX' accessors to be strongly
ordered with respect to each other, even if that is not implicitly
enforced by hardware.
Consequently I have removed all the explicit ordering barriers and
instead submitted a fix for MIPS MMIO implementation, which currently does
not guarantee strong ordering (the MIPS architecture does not define bus
ordering rules except in terms of SYNC barriers), as recorded here:
<https://patchwork.linux-mips.org/project/linux-mips/list/?series=1538>.
Enforcing strong MMIO ordering can be costly however and is often
unnecessary, e.g. when using PIO to access network frame data in onboard
packet memory. I have therefore retained the information that would be
lost by the removal of barriers, by defining accessor wrappers suffixed by
`_o' and `_u', for accesses that have to be ordered and can be unordered
respectively.
If we ever have an API defined for weakly-ordered MMIO accesses, then
these wrappers can be redefined accordingly. Right now they all expand to
the respective `_relaxed' accessors, because, again, enforcing the
ordering WRT DMA transfers can be costly and we don't need it here except
in one place, where I chose to use explicit `dma_rmb' instead.
Similarly I have replaced the completion barriers with a read back from
the respective MMIO location (all adapter MMIO registers can be read with
no side effects incurred), which will serve its purpose on the basis of
MMIO being strongly ordered (although a read from TURBOchannel is going to
be slower than `iob', making the delay incurred unnecessarily longer).
And last but not least, I have split off the SMT Tx network tap support
to a separate change, 2/2 in this series, so that it does not block the
driver proper and can be discussed separately.
I think it has value in that it makes the view of the outgoing network
traffic complete, as if one actually physically tapped into the outgoing
line of the ring, between the station being examined and its downstream
neighbour. Without this part only traffic passed from applications
through the whole protocol stack can be captured and this is only a part
of the view.
With the `dev_queue_xmit_nit' interface now exported it's only
`ptype_all' that remains private, and to define a properly abstracted API
I propose to provide am exported `dev_nit_active' predicate that tells
whether any taps are active. This predicate is then used accordingly.
NB if there is a long-term maintenance concern about the `dev_nit_active'
predicate, then well, corresponding inline code currently present in
`xmit_one' has to be maintained anyway, and if the resulting changes
require `defza' to be updated accordingly, then I am going to handle it;
after some 20 years with Linux it's not that I am going to disappear
anywhere anytime. And once I am dead, which is inevitably going to happen
sooner or later, then the driver can simply be ripped from the kernel.
Though I suspect that at that point no DECstation Linux users may survive
anymore, even though hardware, being as sturdy as it is, likely will.
I have a patch for `tcpdump' to actually decode SMT frames, which I plan
to upstream sometime. Here's a sample of SMT traffic captured through the
`defza' driver in a small network of 4 stations and no concentrators,
printed in the most verbose mode:
01:16:59.138381 4f 00:60:b0:58:41:e7 00:60:b0:58:41:e7 73: SMT NIF ann vid:1 tid:00000270 sid:00-00-00-60-b0-58-41-e7 len:40: UNA: 00 00 00 06 0d 1a 02 ae StationDescr: 00 01 02 00 StationState: 00 00 30 00 MACFrameStatusFunctions.3: 00 00 00 01
01:17:00.332750 4f 08:00:2b:a3:a3:29 08:00:2b:a3:a3:29 73: SMT NIF ann vid:1 tid:0000013b sid:00-00-08-00-2b-a3-a3-29 len:40: UNA: 00 00 00 06 0d 1a 82 e7 StationDescr: 00 01 02 00 StationState: 00 00 30 00 MACFrameStatusFunctions.3: 00 00 00 01
01:17:00.354479 4f 00:60:b0:58:40:75 00:60:b0:58:40:75 73: SMT NIF ann vid:1 tid:0000029c sid:00-00-00-60-b0-58-40-75 len:40: UNA: 00 00 10 00 d4 74 b6 ae StationDescr: 00 01 02 00 StationState: 00 00 31 00 MACFrameStatusFunctions.3: 00 00 00 01
01:17:00.442175 4f 00:60:b0:58:41:e7 Broadcast 73: SMT NIF req vid:1 tid:00000271 sid:00-00-00-60-b0-58-41-e7 len:40: UNA: 00 00 00 06 0d 1a 02 ae StationDescr: 00 01 02 00 StationState: 00 00 30 00 MACFrameStatusFunctions.3: 00 00 00 01
01:17:00.448657 41 08:00:2b:a3:a3:29 00:60:b0:58:41:e7 73: SMT NIF rsp vid:1 tid:00000271 sid:00-00-08-00-2b-a3-a3-29 len:40: UNA: 00 00 00 06 0d 1a 82 e7 StationDescr: 00 01 02 00 StationState: 00 00 30 00 MACFrameStatusFunctions.3: 00 00 00 01
01:17:01.015152 4f 08:00:2b:a3:a3:29 Broadcast 73: SMT NIF req vid:1 tid:0000013c sid:00-00-08-00-2b-a3-a3-29 len:40: UNA: 00 00 00 06 0d 1a 82 e7 StationDescr: 00 01 02 00 StationState: 00 00 30 00 MACFrameStatusFunctions.3: 00 00 00 01
01:17:01.111644 41 08:00:2b:2e:6d:75 08:00:2b:a3:a3:29 73: SMT NIF rsp vid:1 tid:0000013c sid:00-00-08-00-2b-2e-6d-75 len:40: UNA: 00 00 10 00 d4 c5 c5 94 StationDescr: 00 01 01 00 StationState: 00 00 11 00 MACFrameStatusFunctions.2: 00 00 00 01
01:17:04.814603 4f 08:00:2b:2e:6d:75 Broadcast 73: SMT NIF req vid:1 tid:0000013c sid:00-00-08-00-2b-2e-6d-75 len:40: UNA: 00 00 10 00 d4 c5 c5 94 StationDescr: 00 01 01 00 StationState: 00 00 11 00 MACFrameStatusFunctions.2: 00 00 00 01
01:17:04.814939 4f 08:00:2b:2e:6d:75 Broadcast 73: SMT NIF req vid:1 tid:0000013c sid:00-00-08-00-2b-2e-6d-75 len:40: UNA: 00 00 10 00 d4 c5 c5 94 StationDescr: 00 01 01 00 StationState: 00 00 11 00 MACFrameStatusFunctions.2: 00 00 00 01
01:17:04.820960 4f 08:00:2b:2e:6d:75 08:00:2b:2e:6d:75 73: SMT NIF ann vid:1 tid:0000013b sid:00-00-08-00-2b-2e-6d-75 len:40: UNA: 00 00 10 00 d4 c5 c5 94 StationDescr: 00 01 01 00 StationState: 00 00 11 00 MACFrameStatusFunctions.2: 00 00 00 01
Questions, comments? Otherwise, please apply.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
DEC FDDIcontroller 700 (DEFZA) uses a Tx/Rx queue pair to communicate
SMT frames with adapter's firmware. Any SMT frame received from the RMC
via the Rx queue is queued back by the driver to the SMT Rx queue for
the firmware to process. Similarly the firmware uses the SMT Tx queue
to supply the driver with SMT frames which are queued back to the Tx
queue for the RMC to send to the ring.
When a network tap is attached to an FDDI interface handled by `defza'
any incoming SMT frames captured are queued to our usual processing of
network data received, which in turn delivers them to any listening
taps.
However the outgoing SMT frames produced by the firmware bypass our
network protocol stack and are therefore not delivered to taps. This in
turn means that taps are missing a part of network traffic sent by the
adapter, which may make it more difficult to track down network problems
or do general traffic analysis.
Call `dev_queue_xmit_nit' then in the SMT Tx path, having checked that
a network tap is attached, with a newly-created `dev_nit_active' helper
wrapping the usual condition used in the transmit path.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for the DEC FDDIcontroller 700 (DEFZA), Digital Equipment
Corporation's first-generation FDDI network interface adapter, made for
TURBOchannel and based on a discrete version of what eventually became
Motorola's widely used CAMEL chipset.
The CAMEL chipset is present for example in the DEC FDDIcontroller
TURBOchannel, EISA and PCI adapters (DEFTA/DEFEA/DEFPA) that we support
with the `defxx' driver, however the host bus interface logic and the
firmware API are different in the DEFZA and hence a separate driver is
required.
There isn't much to say about the driver except that it works, but there
is one peculiarity to mention. The adapter implements two Tx/Rx queue
pairs.
Of these one pair is the usual network Tx/Rx queue pair, in this case
used by the adapter to exchange frames with the ring, via the RMC (Ring
Memory Controller) chip. The Tx queue is handled directly by the RMC
chip and resides in onboard packet memory. The Rx queue is maintained
via DMA in host memory by adapter's firmware copying received data
stored by the RMC in onboard packet memory.
The other pair is used to communicate SMT frames with adapter's
firmware. Any SMT frame received from the RMC via the Rx queue must be
queued back by the driver to the SMT Rx queue for the firmware to
process. Similarly the firmware uses the SMT Tx queue to supply the
driver with SMT frames that must be queued back to the Tx queue for the
RMC to send to the ring.
This solution was chosen because the designers ran out of PCB space and
could not squeeze in more logic onto the board that would be required to
handle this SMT frame traffic without the need to involve the driver, as
with the later DEFTA/DEFEA/DEFPA adapters.
Finally the driver does some Frame Control byte decoding, so to avoid
magic numbers some macros are added to <linux/if_fddi.h>.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Configuring generic network device parameters on tun will fail in
presence of IFLA_INFO_KIND attribute in IFLA_LINKINFO nested attribute
since tun_validate() always return failure.
This can be visualized with following ip-link(8) command sequences:
# ip link set dev tun0 group 100
# ip link set dev tun0 group 100 type tun
RTNETLINK answers: Invalid argument
with contrast to dummy and veth drivers:
# ip link set dev dummy0 group 100
# ip link set dev dummy0 type dummy
# ip link set dev veth0 group 100
# ip link set dev veth0 group 100 type veth
Fix by returning zero in tun_validate() when @data is NULL that is
always in case since rtnl_link_ops->maxtype is zero in tun driver.
Fixes: f019a7a594d9 ("tun: Implement ip link del tunXXX")
Signed-off-by: Serhey Popovych <serhe.popovych@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sess_err_stats are currently filled on NOP ping timeout, but not Data-Out
timeout. Stash details of Data-Out timeouts using a
ISCSI_SESS_ERR_CXN_TIMEOUT value for last_sess_failure_type.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Replace existing nested code blocks with helper function calls.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Events resulting in connection outages like this should be logged as
errors. Include the I_T Nexus in the message to aid path identification.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Data-Out timeouts resulting in connection outages should be logged as
errors. Include the I_T Nexus in the message to aid path identification.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Move the ISCSI_IQN_LEN definition up, so that it can be used in more
places instead of a hardcoded value.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In dev_ethtool(), the eth command 'ethcmd' is firstly copied from the
use-space buffer 'useraddr' and checked to see whether it is
ETHTOOL_PERQUEUE. If yes, the sub-command 'sub_cmd' is further copied from
the user space. Otherwise, 'sub_cmd' is the same as 'ethcmd'. Next,
according to 'sub_cmd', a permission check is enforced through the function
ns_capable(). For example, the permission check is required if 'sub_cmd' is
ETHTOOL_SCOALESCE, but it is not necessary if 'sub_cmd' is
ETHTOOL_GCOALESCE, as suggested in the comment "Allow some commands to be
done by anyone". The following execution invokes different handlers
according to 'ethcmd'. Specifically, if 'ethcmd' is ETHTOOL_PERQUEUE,
ethtool_set_per_queue() is called. In ethtool_set_per_queue(), the kernel
object 'per_queue_opt' is copied again from the user-space buffer
'useraddr' and 'per_queue_opt.sub_command' is used to determine which
operation should be performed. Given that the buffer 'useraddr' is in the
user space, a malicious user can race to change the sub-command between the
two copies. In particular, the attacker can supply ETHTOOL_PERQUEUE and
ETHTOOL_GCOALESCE to bypass the permission check in dev_ethtool(). Then
before ethtool_set_per_queue() is called, the attacker changes
ETHTOOL_GCOALESCE to ETHTOOL_SCOALESCE. In this way, the attacker can
bypass the permission check and execute ETHTOOL_SCOALESCE.
This patch enforces a check in ethtool_set_per_queue() after the second
copy from 'useraddr'. If the sub-command is different from the one obtained
in the first copy in dev_ethtool(), an error code EINVAL will be returned.
Fixes: f38d138a7da6 ("net/ethtool: support set coalesce per queue")
Signed-off-by: Wenwen Wang <wang6495@umn.edu>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In ethtool_get_rxnfc(), the eth command 'cmd' is compared against
'ETHTOOL_GRXFH' to see whether it is necessary to adjust the variable
'info_size'. Then the whole structure of 'info' is copied from the
user-space buffer 'useraddr' with 'info_size' bytes. In the following
execution, 'info' may be copied again from the buffer 'useraddr' depending
on the 'cmd' and the 'info.flow_type'. However, after these two copies,
there is no check between 'cmd' and 'info.cmd'. In fact, 'cmd' is also
copied from the buffer 'useraddr' in dev_ethtool(), which is the caller
function of ethtool_get_rxnfc(). Given that 'useraddr' is in the user
space, a malicious user can race to change the eth command in the buffer
between these copies. By doing so, the attacker can supply inconsistent
data and cause undefined behavior because in the following execution 'info'
will be passed to ops->get_rxnfc().
This patch adds a necessary check on 'info.cmd' and 'cmd' to confirm that
they are still same after the two copies in ethtool_get_rxnfc(). Otherwise,
an error code EINVAL will be returned.
Signed-off-by: Wenwen Wang <wang6495@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Originally, we have an issue where r8169 MSI-X interrupt is broken after
S3 suspend/resume on RTL8106e of ASUS X441UAR.
02:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd.
RTL8101/2/6E PCI Express Fast/Gigabit Ethernet controller [10ec:8136]
(rev 07)
Subsystem: ASUSTeK Computer Inc. RTL810xE PCI Express Fast
Ethernet controller [1043:200f]
Flags: bus master, fast devsel, latency 0, IRQ 16
I/O ports at e000 [size=256]
Memory at ef100000 (64-bit, non-prefetchable) [size=4K]
Memory at e0000000 (64-bit, prefetchable) [size=16K]
Capabilities: [40] Power Management version 3
Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
Capabilities: [70] Express Endpoint, MSI 01
Capabilities: [b0] MSI-X: Enable+ Count=4 Masked-
Capabilities: [d0] Vital Product Data
Capabilities: [100] Advanced Error Reporting
Capabilities: [140] Virtual Channel
Capabilities: [160] Device Serial Number 01-00-00-00-36-4c-e0-00
Capabilities: [170] Latency Tolerance Reporting
Kernel driver in use: r8169
Kernel modules: r8169
We found the all of the values in PCI BAR=4 of the ethernet adapter
become 0xFF after system resumes. That breaks the MSI-X interrupt.
Therefore, we can only fall back to MSI interrupt to fix the issue at
that time.
However, there is a commit which resolves the drivers getting nothing in
PCI BAR=4 after system resumes. It is 04cb3ae895d7 "PCI: Reprogram
bridge prefetch registers on resume" by Daniel Drake.
After apply the patch, the ethernet adapter works fine before suspend
and after resume. So, we can revert the workaround after the commit
"PCI: Reprogram bridge prefetch registers on resume" is merged into main
tree.
This patch reverts commit 7bb05b85bc2d1a1b647b91424b2ed4a18e6ecd81
"r8169: don't use MSI-X on RTL8106e".
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=201181
Fixes: 7bb05b85bc2d ("r8169: don't use MSI-X on RTL8106e")
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Update registers as follows:
- Default value of AIP timer is 1ms, and it is easy for some expanders to
cause IO error. Change the value to max value 65ms to avoid IO error for
those expanders.
- A CQ completion will be reported by HW when 4 CQs have occurred or the
aging timer expires, whichever happens first. Sor serial IO scenario, it
will still wait 8us for every IO before it is reported. So in the
situation, the performance is poor. So to improve it, change the limit
time to the least value.
For other scenario, it does little affect to the performance.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Currently we use the IPTT defined in LLDD to identify IOs. Actually for
IOs which are from the block layer, they have tags to identify them. So
for those IOs, use tag of the block layer directly, and for IOs which is
not from the block layer (such as internal IOs from libsas/LLDD), reserve
96 IPTTs for them.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The interrupts of ent72 and ent74 are not processed by PCIe AER handling,
so we need to unmask the interrupts and process them first in the driver.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
If an SSP/SMP IO times out, it may be actually in reality be
simultaneously processing completion of the slot in
slot_complete_vx_hw().
Then if the slot is freed in slot_complete_vx_hw() (this IPTT is freed
and it may be re-used by other slot), and we may abort the wrong slot in
hisi_sas_abort_task().
So to solve the issue, free the slot after the check of
SAS_TASK_STATE_ABORTED in slot_complete_vx_hw().
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
SMP/internal IO
If SMP/internal IO times out, we will possibly free the task immediately.
However if the IO actually completes at the same time, the IO completion
may refer to task which has been freed.
So to solve the issue, flush the tasklet to finish IO completion before
free'ing slot/task.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In evaluating hisi_hba, the sas_port may be NULL, so for safety relocate
the the check to value possible NULL deference.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
At directly attached situation, if the user modifies the sysfs interface
of maximum_linkrate and minimum_linkrate to renegotiate the linkrate
between SAS controller and target, the value of both files mentioned
above should have change to user setting after renegotiate is over, but
it remains unchanged.
To fix this bug, maximum_linkrate and minimum_linkrate will be directly
fed back to relevant sas_phy structure.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
With the addition of commit 00d909a10710 ("scsi: target: Make the session
shutdown code also wait for commands that are being aborted") in v4.19-rc, it
incorrectly assumes no signals will be pending for task_struct executing the
normal session shutdown and I/O quiesce code-path.
For example, iscsi-target and iser-target issue SIGINT to all kthreads as part
of session shutdown. This has been the behaviour since day one.
As-is when signals are pending with se_cmds active in se_sess->sess_cmd_list,
wait_event_interruptible_lock_irq_timeout() returns a negative number and
immediately kills the machine because of the do while (ret <= 0) loop that was
added in commit 00d909a107 to spin while backend I/O is taking any amount of
extended time (say 30 seconds) to complete.
Here's what it looks like in action with debug plus delayed backend I/O
completion:
[ 4951.909951] se_sess: 000000003e7e08fa before target_wait_for_sess_cmds
[ 4951.914600] target_wait_for_sess_cmds: signal_pending: 1
[ 4951.918015] wait_event_interruptible_lock_irq_timeout ret: -512 signal_pending: 1 loop count: 0
[ 4951.921639] wait_event_interruptible_lock_irq_timeout ret: -512 signal_pending: 1 loop count: 1
[ 4951.921944] wait_event_interruptible_lock_irq_timeout ret: -512 signal_pending: 1 loop count: 2
[ 4951.921944] wait_event_interruptible_lock_irq_timeout ret: -512 signal_pending: 1 loop count: 3
[ 4951.921944] wait_event_interruptible_lock_irq_timeout ret: -512 signal_pending: 1 loop count: 4
[ 4951.921944] wait_event_interruptible_lock_irq_timeout ret: -512 signal_pending: 1 loop count: 5
[ 4951.921944] wait_event_interruptible_lock_irq_timeout ret: -512 signal_pending: 1 loop count: 6
[ 4951.921944] wait_event_interruptible_lock_irq_timeout ret: -512 signal_pending: 1 loop count: 7
[ 4951.921944] wait_event_interruptible_lock_irq_timeout ret: -512 signal_pending: 1 loop count: 8
[ 4951.921944] wait_event_interruptible_lock_irq_timeout ret: -512 signal_pending: 1 loop count: 9
... followed by the usual RCU CPU stalls and deadlock.
There was never a case pre commit 00d909a107 where
wait_for_complete(&se_cmd->cmd_wait_comp) was able to be interrupted, so to
address this for v4.19+ moving forward go ahead and use
wait_event_lock_irq_timeout() instead so new code works with all fabric
drivers.
Also for commit 00d909a107, fix a minor regression in
target_release_cmd_kref() to only wake_up the new se_sess->cmd_list_wq only
when shutdown has actually been triggered via se_sess->sess_tearing_down.
Fixes: 00d909a10710 ("scsi: target: Make the session shutdown code also wait for commands that are being aborted")
Cc: <stable@vger.kernel.org> # v4.19+
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Tested-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Reviewed-by: Bryant G. Ly <bly@catalogicsoftware.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Short of reverting commit 00d909a10710 ("scsi: target: Make the session
shutdown code also wait for commands that are being aborted") for v4.19,
target-core needs a wait_event_t macro can be executed using
TASK_UNINTERRUPTIBLE to function correctly with existing fabric drivers that
expect to run with signals pending during session shutdown and active se_cmd
I/O quiesce.
The most notable is iscsi-target/iser-target, while ibmvscsi_tgt invokes
session shutdown logic from userspace via configfs attribute that could also
potentially have signals pending.
So go ahead and introduce wait_event_lock_irq_timeout() to achieve this, and
update + rename __wait_event_lock_irq_timeout() to make it accept 'state' as a
parameter.
Fixes: 00d909a10710 ("scsi: target: Make the session shutdown code also wait for commands that are being aborted")
Cc: <stable@vger.kernel.org> # v4.19+
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Reviewed-by: Bryant G. Ly <bly@catalogicsoftware.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
When we fail to analyse the payload of a PRLI response we should reset
the state machine to retry the PRLI; eventually we will be getting a
proper frame. Not doing so will result in a stuck state machine and the
port never to be presented to the systsm.
Suggested-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Arun Easi <arun.easi@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
We should not assume the payload of a PRLI or PLOGI respons is always
present.
Signed-off-by: Thomas Abraham <tabraham@suse.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Arun Easi <arun.easi@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
When an RSCN gets delayed (or not being sent at all), the transport class
will detect an error, EH kicks in, and eventually will be setting the
device to offline. If we receive an RSCN after that, the device will
stay in 'offline'. This patch allows for an 'offline' to 'blocked'
transition, thereby allowing the device to become active again.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The dma_addr_t member is unused ever since we switched the SCSI
layer to send down single-segement command using a scatterlist
as well many years ago.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Except for the mac_esp driver, which uses PIO or pseudo DMA, all drivers
share the same dma mapping calls. Move the dma mapping into the core
code using the scsi_dma_map / scsi_dma_unmap helpers, with a special
identify mapping variant triggered off a new ESP_FLAG_NO_DMA_MAP flag
for mac_esp.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
We can simplify use esp->dev now.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
