| Age | Commit message (Collapse) | Author |
|---|
|
On some x86 platforms, the LED gpio is active high
instead of active low. Identify such cards and modify
the GPIO usage to make sure LED works properly.
Cc: Russell Hu <rhu@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch updates the initvals for QCA953x v1.1 and v2.0
Signed-off-by: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
* Duplicates have been marked.
* New initvals for 1.1 and 2.0 versions.
* xPA support.
* Fix for low power issue.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
In secured mesh, the unicast mgmt frame is encrypted using
the same key that used for encrypting the unicast data frame.
This patch "ath9k_htc_firmware: fix the offset of CCMP header
for mesh data frame" applied to open-ath9k-htc-firmware allows
the ath9k_htc to be loaded without "nohwcrypt=1". Unfortunately,
this is not working and we still need CCMP encryption of
transmitted management frames to be done in software.
So this patch allows the software encryption for transmitted
management frame to be done in software but remain the hardware
decryption for received management frame.
This patch is tested with the following hardwares:
- TP-Link TL-WN821N v3 802.11n [Atheros AR7010+AR9287]
- AR9271 802.11n
and managed to work with peer mesh STA equipped with ath9k.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Use the sw_mgmt_crypto_tx flag to trigger the CCMP encryption
for transmitted management frames to be done in software while
the sw_mgmt_crypto_rx flag is used to trigger the CCMP decryption
for received management frames to be done in software.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Auto TDLS support is enabled per device. As of now add this
feature only for SD8887.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch adds support for parsing TDLS discovery
frames. After parsing, we update peer RSSI information.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch adds auto TDLS support to mwifiex.
Auto TDLS functionality works as follows:
1. Whenever userspace application has triggered TDLS connection with
any peer, driver would store this peer mac address details in its database.
2. After this driver whenever driver receives packet on direct link,
it would store rssi and timestamp in peer information.
3. Whenever a packet is to be transmitted to non-AP peer in station mode,
driver would check if TDLS link can be established by looking at peer RSSI
information. Driver would initiate TDLS setup in such cases.
4. Periodic timer is used for updating peer information.
5. Auto TDLS peer list & timer are cleared during disconnection or driver unload.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch adds WMM support for TDLS link. Patch
add WMM info IE for TDLS setup request/response frames
while WMM parameter for TDLS confirm frame.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When Teardown event from FW is indicated to userspace, userspace
would trigger tdls_oper handler to disable TDLS link.
We need not do this explicitly here.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
RX packet descriptor structure has recently changed in FW.
This patch updates rxpd accordingly.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
We need to assign the hw queues for mesh interface. Otherwise,
we are not able to bring up the mesh interface due to the
IEEE80211_INVAL_HW_QUEUE error.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
we can have here two variants. Add
ATH9K_CMN_DEBUGFS y if ATH9K_CMN_DEBUGFS || ATH9K_HTC_DEBUGFS
wich will add more configurations and testcases. Or remove ATH9K_HTC_DEBUGFS
which need more time to be done.
So, make common-spectral ignore ATH9K_DEBUGFS option for now.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
drivers/net/wireless/ath/ath9k/htc_drv_init.c:56:6: sparse: symbol 'ath9k_htc_op_ps_wakeup' was not declared. Should it be static?
drivers/net/wireless/ath/ath9k/htc_drv_init.c:61:6: sparse: symbol 'ath9k_htc_op_ps_restore' was not declared. Should it be static?
drivers/net/wireless/ath/ath9k/htc_drv_init.c:66:19: sparse: symbol 'ath9k_htc_ps_ops' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
drivers/net/wireless/ath/ath9k/init.c:91:6: sparse: symbol 'ath9k_op_ps_wakeup' was not declared. Should it be static?
drivers/net/wireless/ath/ath9k/init.c:96:6: sparse: symbol 'ath9k_op_ps_restore' was not declared. Should it be static?
drivers/net/wireless/ath/ath9k/init.c:101:19: sparse: symbol 'ath9k_ps_ops' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch adds module load parameter driver_mode for mwifiex
which would enable driver to create AP or P2P client interface while loading
module. driver_mode is bitmap of interface modes for station, AP and
P2P client.
Station interface is created by default and is unaffected by driver_mode
parameter.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When channel-context is not enabled, all vifs belong to
the first context, but it is not configured as 'assigned'.
Fix misc debugfs file to print out info for non-assigned
contexts, and also print whether ctx is assigned or not.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Kalle Valo <kvalo@qca.qualcomm.com> says:
"One ath6kl patch and rest for ath10k, but nothing really major which
stands out. Most notable:
o fix resume (Bartosz)
o firmware restart is now faster and more reliable (Michal)
o it's now possible to test hardware restart functionality without
crashing the firmware using hw-restart parameter with
simulate_fw_crash debugfs file (Michal)"
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Return value of irq_of_parse_and_map() is unsigned int, with 0
indicating failure, so testing for negative result never works.
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Cc: stable@vger.kernel.org # v3.17
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Kill the submitted URB in brcmf_usb_dl_cmd if the request timed out. This
assures the URB is never submitted twice. It also prevents a possible
use-after-free of the URB transfer buffer if a timeout occurs.
Signed-off-by: Mathy Vanhoef <vanhoefm@gmail.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The commit that went into 3.17:
ath9k: Summarize hw state per channel context
Group and set hw state (opmode, primary_sta, beacon conf) per
channel context instead of whole list of vifs. This would allow
each channel context to run in different mode (STA/AP).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
broke multi-vif configuration due to not properly calculating
the bssid mask.
The test case that caught this was:
create wlan0 and sta0-4 (6 total), not sure how much that matters.
associate all 6 (works fine)
disconnect 5 of them, leaving sta0 up
Start trying to bring up the other 5 one at a time. It will
fail, with iw events looking like this (in these logs, several
sta are trying to come up, but symptom is the same with just one)
The patch causing the regression made quite a few changes, but
the part I think caused this particular problem was not
recalculating the bssid mask when adding and removing interfaces.
Re-adding those calls fixes my test case. Fix bad comment
as well.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Trivial fix to check the A bit of CCCR for memory frequency
calculations, where the shift of the bit index was missing, triggering a
wrong calculation of memory frequency.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
|
|
Commit 79c6ab509558 (clk: divider: add CLK_DIVIDER_READ_ONLY flag) in
v3.16 introduced the CLK_DIVIDER_READ_ONLY flag which caused the
recalc_rate() and round_rate() clock callbacks to be omitted.
However using this flag has the unfortunate side effect of causing the
clock recalculation code when a clock rate change is attempted to always
treat it as a pass-through clock, i.e. with a fixed divide of 1, which
may not be the case. Child clock rates are then recalculated using the
wrong parent rate.
Therefore instead of dropping the recalc_rate() and round_rate()
callbacks, alter clk_divider_bestdiv() to always report the current
divider as the best divider so that it is never altered.
For me the read only clock was the system clock, which divided the PLL
rate by 2, from which both the UART and the SPI clocks were divided.
Initial setting of the UART rate set it correctly, but when the SPI
clock was set, the other child clocks were miscalculated. The UART clock
was recalculated using the PLL rate as the parent rate, resulting in a
UART new_rate of double what it should be, and a UART which spewed forth
garbage when the rate changes were propagated.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Thomas Abraham <thomas.ab@samsung.com>
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Max Schwarz <max.schwarz@online.de>
Cc: <stable@vger.kernel.org> # v3.16+
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
|
|
There is a duplication in a clock name for apq8084 platform that causes
the following warning: "RBCPR_CLK_SRC" redefined
Resolve this by adding a MMSS_ prefix to this clock and making its name
coherent with msm8974 platform.
Fixes: 2b46cd23a5a2 ("clk: qcom: Add APQ8084 Multimedia Clock Controller (MMCC) support")
Signed-off-by: Georgi Djakov <gdjakov@mm-sol.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
|
|
First check for rate == 0 in set_rate and round_rate to avoid div by zero.
Then, in order to get the closest rate, round all divisions to the closest
result instead of rounding them down.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
|
|
at91rm9200_clk_usb_set_rate might fail depending on the requested rate,
because the parent_rate / rate remainder is not necessarily zero.
Moreover, when rounding down the calculated rate we might alter the
divisor calculation and end up with an invalid divisor.
To solve those problems, accept a non zero remainder, and always round
division to the closest result.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reported-by: Andreas Henriksson <andreas.henriksson@endian.se>
Tested-by: Andreas Henriksson <andreas.henriksson@endian.se>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
|
|
'asoc/fix/sgtl5000' into asoc-linus
|
|
'asoc/fix/dpcm', 'asoc/fix/es8328', 'asoc/fix/fsl-asrc', 'asoc/fix/max98090', 'asoc/fix/rcar', 'asoc/fix/rockchip' and 'asoc/fix/rt5645' into asoc-linus
|
|
|
|
Fix to use v10.2 wmi call for firmware v10.2.
It turned out that peer association function was using
v10.1 wmi call for v10.2 firmware during code review.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
This will enable AP mode to change channel width dynamically
based on 20/40 intolerance report sent by associated client.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
This patch would help bring up wifi interface with default board
data in case of failures in otp download. It is useful for initial
calibration.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
For packet log, the transmitted frame 802.11 header alone is sufficient.
Recording entire packet is also consuming lot of disk space. To optimize
this, tx and rx data tracepoints are splitted into header and payload
tracepoints.
To record tx ieee80211 headers
trace-cmd record -e ath10k_tx_hdr
To record complete packets
trace-cmd record -e ath10k_tx_hdr -e ath10k_tx_payload
Cc: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
AM4372 SoC has 2 DCAN modules. Add compatible id and
raminit driver data for it. The driver data is same as AM3352
but this gives us flexibility to add AM4372 specific quirks
if required later.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
We should not free any buffers associated with writing out coefficients
to the DSP until all the async writes have completed. This patch updates
the out of memory path when allocating a new buffer to include a call to
regmap_async_complete.
Reported-by: JS Park <aitdark.park@samsung.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
|
|
Specified in section 5.2.5.6.1 of the USB Audio Class 2.0 definition.
Solves the following error for C-Media 6632A (Asus Xonar U7):
[ 8219.676164] cannot get ctl value: req = 0x81, wValue = 0x0, wIndex = 0x1400, type = 3
Signed-off-by: Johan Rastén <johan@oljud.se>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Signed-off-by: Vasily Averin <vvs@parallels.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Currently all the conntrack lookups are done using default zone.
In case the skb has a ct attached (e.g. template) we should use this zone
for lookups instead. This makes connlimit work with connections assigned
to other zones.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Ebtables on the OUTPUT chain (NF_BR_LOCAL_OUT) would not work as expected
for both locally generated IGMP and MLD queries. The IP header specific
filter options are off by 14 Bytes for netfilter (actual output on
interfaces is fine).
NF_HOOK() expects the skb->data to point to the IP header, not the
ethernet one (while dev_queue_xmit() does not). Luckily there is an
br_dev_queue_push_xmit() helper function already - let's just use that.
Introduced by eb1d16414339a6e113d89e2cca2556005d7ce919
("bridge: Add core IGMP snooping support")
Ebtables example:
$ ebtables -I OUTPUT -p IPv6 -o eth1 --logical-out br0 \
--log --log-level 6 --log-ip6 --log-prefix="~EBT: " -j DROP
before (broken):
~EBT: IN= OUT=eth1 MAC source = 02:04:64:a4:39:c2 \
MAC dest = 33:33:00:00:00:01 proto = 0x86dd IPv6 \
SRC=64a4:39c2:86dd:6000:0000:0020:0001:fe80 IPv6 \
DST=0000:0000:0000:0004:64ff:fea4:39c2:ff02, \
IPv6 priority=0x3, Next Header=2
after (working):
~EBT: IN= OUT=eth1 MAC source = 02:04:64:a4:39:c2 \
MAC dest = 33:33:00:00:00:01 proto = 0x86dd IPv6 \
SRC=fe80:0000:0000:0000:0004:64ff:fea4:39c2 IPv6 \
DST=ff02:0000:0000:0000:0000:0000:0000:0001, \
IPv6 priority=0x0, Next Header=0
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
AM3352 SoC has 2 DCAN modules. Add compatible id and
raminit driver data for am3352 DCAN.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
DRA7 SoC has 2 CAN IPs. Provide compatible IDs and RAMINIT
register data for both.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
DRA7 CAN IP suffers from a problem which causes it to be prevented
from fully turning OFF (i.e. stuck in transition) if the module was
disabled while there was traffic on the CAN_RX line.
To work around this issue we select the SLEEP pin state by default
on probe and use the DEFAULT pin state on CAN up and back to the
SLEEP pin state on CAN down.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Some SoCs e.g. (TI DRA7xx) need a START pulse to start the
RAMINIT sequence i.e. START bit must be set and cleared before
checking for the DONE bit status.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Some TI SoCs like DRA7 have a RAMINIT register specification
different from the other AMxx SoCs and as expected by the
existing driver.
To add more insanity, this register is shared with other
IPs like DSS, PCIe and PWM.
Provides a more generic mechanism to specify the RAMINIT
register location and START/DONE bit position and use the
syscon/regmap framework to access the register.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Some platforms (e.g. TI) need special RAMINIT register handling.
Provide a way to store RAMINIT register description in driver data.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
We want to have more data than just can_dev_id to be present
in the driver data e.g. TI platforms need RAMINIT register
description. Introduce the c_can_driver_data structure and move
the can_dev_id into it.
Tidy up the way it is used on probe().
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
TI's RAMINIT DONE mechanism is buggy on AM43xx SoC and may not always
be set after the START bit is set. Although it seems to work fine even
in that case. So add a timeout mechanism to c_can_hw_raminit_wait_ti().
Don't bail out in that failure case but just print an error message.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Make sure the netlink group exists, otherwise you can trigger an out
of bound array memory access from the netlink_bind() path. This splat
can only be triggered only by superuser.
[ 180.203600] UBSan: Undefined behaviour in ../net/netfilter/nfnetlink.c:467:28
[ 180.204249] index 9 is out of range for type 'int [9]'
[ 180.204697] CPU: 0 PID: 1771 Comm: trinity-main Not tainted 3.18.0-rc4-mm1+ #122
[ 180.205365] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.7.5-0-ge51488c-20140602_164612-nilsson.home.kraxel.org
+04/01/2014
[ 180.206498] 0000000000000018 0000000000000000 0000000000000009 ffff88007bdf7da8
[ 180.207220] ffffffff82b0ef5f 0000000000000092 ffffffff845ae2e0 ffff88007bdf7db8
[ 180.207887] ffffffff8199e489 ffff88007bdf7e18 ffffffff8199ea22 0000003900000000
[ 180.208639] Call Trace:
[ 180.208857] dump_stack (lib/dump_stack.c:52)
[ 180.209370] ubsan_epilogue (lib/ubsan.c:174)
[ 180.209849] __ubsan_handle_out_of_bounds (lib/ubsan.c:400)
[ 180.210512] nfnetlink_bind (net/netfilter/nfnetlink.c:467)
[ 180.210986] netlink_bind (net/netlink/af_netlink.c:1483)
[ 180.211495] SYSC_bind (net/socket.c:1541)
Moreover, define the missing nf_tables and nf_acct multicast groups too.
Reported-by: Andrey Ryabinin <a.ryabinin@samsung.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
We can only use page_address on memory that has been mapped using kmap,
when the buffer passed to the SPI has been allocated by vmalloc the page
has not necessarily been mapped through kmap. This means sometimes
page_address will return NULL causing the pointer we pass to sg_set_buf
to be invalid.
As we only call page_address so that we can pass a virtual address to
sg_set_buf which will then immediately call virt_to_page on it, fix this
by calling sg_set_page directly rather then relying on the sg_set_buf
helper.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
|
|
This patch changes the byteorder handling for short and panid handling.
We now except to get little endian in nl802154 for these attributes.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
