| Age | Commit message (Collapse) | Author |
|---|
|
Even thought sys_nirq1 is hardwired on the SoC for the pin, it is
better to configure the pin to the required mux configuration.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The ldo4_reg regulator provides power to the USB1 and USB2
High Speed PHYs.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add USB data and pinctrl for USB.
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The 4th USB controller instance present only on the DRA74x family of
devices so move it there.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
DRA72-evm has a 256MB 16-bit wide NAND chip. Add
pinmux and NAND node.
The NAND chips 'Chip select' and 'Write protect' can be
controlled using DIP Switch SW5. To use NAND,
the switch must be configured like so:
SW5.1 (NAND_SELn) = ON (LOW)
SW5.9 (GPMC_WPN) = OFF (HIGH)
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Adding CPSW phy-id, CPSW and MDIO pinmux configuration for active and
sleep states and enable them in board evm dts file.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add CPSW and MDIO related device tree data for DRA7XX and made as status
disabled. Phy-id, pinmux for active and sleep state needs to be added in
board dts files and enable the CPSW device.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Use omap specific pinctrl defines (OMAP3_CORE1_IOPAD) to configure
the padconf register offset.
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add DSS related pinmux and display data nodes required to support
DVI video out on SBC-T3530, SBC-T3730 and SBC-T3517.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Cc: devicetree@vger.kernel.org
Reviewed-by: Tony Lindgren <tony@atomide.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Cc: devicetree@vger.kernel.org
Reviewed-by: Tony Lindgren <tony@atomide.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The '#mbox-cells' property is added to all the OMAP mailbox
nodes. This property is mandatory with the new mailbox framework.
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add the interrupts property to all the 13 mailbox nodes in
DRA7xx. The interrupts property information added is inline
with the expected values with the DRA7xx crossbar driver,
and is common to both DRA74x and DRA72x SoCs.
Do note that the mailbox 1 is only capable of generating out
3 interrupts, while all the remaining mailboxes have 4
interrupts each.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into next/dt
Merge "Nomadik updates for the v3.19 series" from Linus Walleij:
Nomadik changes for the v3.19 development series:
- Rearrange the DTS files to make a pure SoC-specific file and
a pure board file for S8815.
- Add the device tree for the NDK15 board.
- Update the defconfig and configure in the STMPE expander by
default on the Nomadik.
* tag 'nomadik-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: nomadik: configure in STMPE support
ARM: update Nomadik config
ARM: nomadik: device tree for NHK15 board
ARM: nomadik: push ethernet down to board
ARM: nomadik: set up MCDATDIR2
ARM: nomadik: move GPIO I2C to S8815 board file
ARM: nomadik: disable chrystals in top level board files
ARM: nomadik: move MMC/SD card detect GPIO to board DTS
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into next/dt
Merge "at91: dt for 3.19 #1" from Nicolas Ferre:
"Very little DT update for AT91. More will come but I want to send this first
batch soon so it doesn't get in the way of larger modifications."
First DT batch for 3.19:
- CAN device nodes for at91sam9263 and at91sam9x5
- at91sam9x5 DMA definitions for usart
* tag 'at91-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91/dt: at91sam9263: Add CAN device nodes
ARM: at91/dt: at91sam9x5: Add CAN device nodes
ARM: at91/dt/trivial: at91sam9x5_can.dtsi: comment and whitespace fixes
ARM: at91: at91sam9x5 dt: add usart dma definitions to dt
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.infradead.org/users/hesselba/linux-berlin into next/dt
Merge "ARM: berlin: DT changes for v3.19 (round 1)" from Sebastian Hesselbarth:
"This is Berlin DT changes for v3.19 and contains those patches that missed
the v3.18 merge window plus corresponding patches to catch-up with Antoine's
BG2Q improvements for BG2 and BG2CD. We now have working SDHCI and Ethernet
on all SoCs (well, BG2CD has HDMI HEC only), SATA PHY support for BG2 is still
pending."
Berlin DT changes for v3.19 (round 1)
- AHCI and SATA PHY nodes for BG2Q
- Reset controller binding docs
- Ethernet nodes for BG2, BG2CD
- SDHCI nodes for BG2, BG2CD
- Corresponding board changes to enable AHCI, Ethernet, SDHCI
* tag 'berlin-dt-3.19-1' of git://git.infradead.org/users/hesselba/linux-berlin:
ARM: dts: berlin: Enable eMMC on Sony NSZ-GS7
ARM: dts: berlin: Enable WiFi on Google Chromecast
ARM: dts: berlin: Add SDHCI controller nodes to BG2/BG2CD
ARM: dts: berlin: Enable ethernet on Sony NSZ-GS7
ARM: dts: berlin: Add phy-connection-type to BG2Q Ethernet
ARM: dts: berlin: Add BG2CD ethernet DT nodes
ARM: dts: berlin: Add BG2 ethernet DT nodes
ARM: dts: berlin: Add GPIO leds to Google Chromecast
ARM: dts: berlin: enable timer 1 for sched_clock
ARM: dts: berlin: add a required reset property in the chip controller node
Documentation: bindings: add reset bindings docs for Marvell Berlin SoCs
ARM: dts: berlin: enable the eSATA interface on the BG2Q DMP
ARM: dts: berlin: add the AHCI node for the BG2Q
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.stlinux.com/devel/kernel/linux-sti into next/dt
Merge "STi DT updates for v3.19, round 1" from Maxime Coquelin:
Highlights:
-----------
- Add SDHCI support for STiH41x B2020 boards
- Add reset controllers to STiH407 SoC
- Add MiPHY & SATA support to STiH416
- Add Thermal supportto STiH416
- Add Clock support to STiH407 SoC
This tag also includes STiH407 bindings definitions for reset controller.
* tag 'sti-dt-for-v3.19-1' of git://git.stlinux.com/devel/kernel/linux-sti:
ARM: STi: DT: STiH407: Fix: clk-tmds-hdmi clock is missing
ARM: STi: DT: STiH407: Add all defines for STiH407 DT clocks
ARM: STi: DT: STiH407: 407 DT Entry for clockgenA9
ARM: STi: DT: STiH407: 407 DT Entry for clockgen D0/D2/D3
ARM: STi: DT: STiH407: 407 DT Entry for clockgen C0
ARM: STi: DT: STiH407: 407 DT Entry for clockgen A0
ARM: DT: STi: STiH416: Add DT node for ST's SATA device
ARM: DT: STi: STiH416: Add DT node for MiPHY365x
ARM: STi: DT: STiH416: Supply Thermal Controller Device Tree nodes
ARM: STi: DT: Enable second sdhci controller for stih416 b2020 boards.
ARM: STi: DT: Enable mmc0 for both stih415 and stih416 SoCs
ARM: STi: DT: Add sdhci controller for stih415
ARM: STi: DT: Add sdhci pin configuration for stih415
ARM: STi: DT: Add sdhci controller for stih416
ARM: STi: DT: Add sdhci pins for stih416
ARM: sti: Add STiH407 reset controller support.
ARM: sti: Add STiH407 Kconfig entry to select STIH407_RESET
ARM: STi: DT: STiH41x: Convert all uppercase non-defines to lowercase
reset: stih407: Add reset controllers DT bindings
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
into next/dt
Merge "Broadcom Cygnus SoC Device Tree changes" from Florian Fianelli:
This patchset contains initial support for Broadcom's Cygnus SoC based on our
iProc architecture. Initial support is minimal and includes just the mach
platform code, clock driver, and a basic device tree configuration. Peripheral
drivers will be submitted soon, as will device tree configurations for other
Cygnus board variants.
These are the Device Tree changes
* tag 'arm-soc/for-3.18/cygnus-dts-v9' of http://github.com/brcm/linux:
ARM: dts: Enable Broadcom Cygnus SoC
dt-bindings: Document Broadcom Cygnus SoC and clocks
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Reuse syscon-reboot, drivers/power/reset/syscon-reboot.c
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
|
|
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
|
|
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
|
|
Signed-off-by: Jiancheng Xue <xuejiancheng@huawei.com>
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
|
|
Signed-off-by: Jiancheng Xue <xuejiancheng@huawei.com>
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
|
|
Signed-off-by: Jiancheng Xue <xuejiancheng@huawei.com>
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
|
|
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Jiancheng Xue <xuejiancheng@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
|
|
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
|
|
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
|
|
This enables the STMPE MFD, GPIO and keypad support by default on
the Nomadik builds. This expander is used on the NDK 15 board.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This updates the Nomadik (NHK8815) defconfig to what saveconfig
produces after some recent changes to Kconfig fragments here
and there.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Add bindings documentation for the new Atmel DMA controller (XDMAC)
introduced with SAMA5D4.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
New atmel DMA controller known as XDMAC, introduced with SAMA5D4
devices.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Alt is booted from DT, so chosen/stdout-path is
always used, and we can drop the "console=" parameter from chosen/bootargs.
This change has a side-effect of changing the console speed from 38400
to 115200. This is intentional as 115200 is consistently used on
all other shmobile boards.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Ports are named scifb0-3, not scifb2-5.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Merge "Renesas ARM Based SoC DT Clocksource Updates for v3.19" from Simon
Horman:
* sh_mtu2: Drop incorrect SoC family name
* sh_tmu: Document r8a7778 and r8a7740 bindings
* tag 'renesas-dt-clocksource-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
clocksource: sh_mtu2: Drop incorrect SoC family name
clocksource: sh_tmu: Document r8a7778 binding
clocksource: sh_tmu: Document R-Mobile r8a7740 binding
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Merge "first bunch on Rockchip dt changes" from Heiko Stübner:
First hunk of rockchip devicetree patches, containing:
- cpu operating points and supplies
- dma support for spi controllers
- i2s on rk3066 and rk3188
- default core clock settings for rk3288
* tag 'v3.19-rockchip-dts1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: Add SPI DMA into rk3288.dtsi
ARM: dts: rockchip: enable init rate for clock
ARM: dts: rockchip: add I2S controllers for rk3066 and rk3188
ARM: dts: rockchip: enable DMA on SPI for rk3066 and rk3188
ARM: dts: rockchip: add cpu supplies to boards
ARM: dts: rockchip: add operating points and armclk references
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Merge "Renesas ARM Based SoC r8a73a4 DT Timers Updates for v3.19" from Simon
Horman:
* Initialise CMT1 timer using DT
* tag 'renesas-r8a73a4-dt-timers-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a73a4: Remove empty r8a73a4_add_dt_devices
ARM: shmobile: ape6evm-reference: Initialise CMT1 device using DT
ARM: shmobile: r8a73a4: Rename cmt registration helper
ARM: shmobile: r8a73a4: Add CMT1 node
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Merge "Renesas ARM Based SoC DT Cleanups for v3.19" from Simon Horman:
* Add chosen/stdout-path to DTS files for shmobile boards
* Remove r7s72100-genmai.dtb for ARCH_SHMOBILE_LEGACY
- The corresponding board file has already been removed
* Sort dts nodes by address
* Sort SHMOBILE dtbs alphabetically in Makefile
* tag 'renesas-dt-cleanups-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: kzm9d dts: Add chosen/stdout-path
ARM: shmobile: kzm9g-reference dts: Add chosen/stdout-path
ARM: shmobile: alt dts: Add chosen/stdout-path
ARM: shmobile: koelsch dts: Add chosen/stdout-path
ARM: shmobile: henninger dts: Add chosen/stdout-path
ARM: shmobile: lager dts: Add chosen/stdout-path
ARM: shmobile: marzen dts: Add chosen/stdout-path
ARM: shmobile: bockw-reference dts: Add chosen/stdout-path
ARM: shmobile: armadillo800eva dts: Add chosen/stdout-path
ARM: shmobile: ape6evm-reference dts: Add chosen/stdout-path
ARM: shmobile: genmai dts: Add chosen/stdout-path
ARM: shmobile: emev2 dtsi: Add uart* labels for easier referencing
ARM: shmobile: emev2 dtsi: Use generic names for device nodes
ARM: shmobile: r7s72100: Remove r7s72100-genmai.dtb for ARCH_SHMOBILE_LEGACY
ARM: shmobile: r8a73a4: sort dtsi file by address
ARM: shmobile: kzm9d: sort dts file by address
ARM: shmobile: r7s72100: sort dtsi file by address
ARM: shmobile: r8a73a4: Remove spurious dma-multiplexer base addresses
ARM: dts: Sort SHMOBILE dtbs alphabetically
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
K2E SoC has a second PCI port based on Synopsis Designware PCIe h/w.
Add DT bindings to support PCI controller for port 1 for this SoC.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
|
|
Add common DT bindings to support PCI controller driver for port 0 on all
of the K2 SoCs that has Synopsis Designware based pcie h/w.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
|
|
Keystone K2L-EVM has two 1G Marvell 88E1514 Ethernet PHYs
installed, which are compatible with 88E1510.
Hence, add corresponding child nodes for 1G MDIO bus.
For more information see:
https://www.einfochips.com/index.php/partnerships/texas-instruments/k2l-evm.html
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
|
|
Keystone K2E-EVM has two 1G Marvell 88E1514 Ethernet PHYs
installed, which are compatible with 88E1510.
Hence, add corresponding child nodes for 1G MDIO bus.
For more information see:
https://www.einfochips.com/index.php/partnerships/texas-instruments/k2e-evm.html
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into next/dt
Merge "RealView DeviceTree support for v3.19" from Linus Walleij:
- Device Tree implementation for the ARM RealView boards
- DTS file for the ARM RealView PB1176
- Updates on top of the same DTS file
* tag 'arm-realview-dt-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: realview: add MMCI to the PB1176 DTS
ARM: realview: add KMIs to the PB1176 DTS
ARM: realview: add FPGA UART4 to PB1176 DTS
ARM: realview: add PL022 SSP/SPI block to PB1176 DTS
ARM: realview: add RTC clocks to device tree
ARM: realview: add charlcd to PB1176 device tree
ARM: realview: add PL061 GPIO to the PB1176 DTS
ARM: realview: move DT GIC to FPGA node
ARM: realview: add device tree and bindings for PB1176
ARM: realview: basic device tree implementation
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt
Merge "1st Round of Samsung DT updates for v3.19" from Kukjin Kim:
Samsung DT updates for v3.19
- add CPU nodes for exynos4210, exynos4212, exynos4412
- exynos4x12-pinctrl: add utility macro to define pin sleep states
- exynos4412-trats2: add Maxim77693 PMIC node, add sleep mode pin
configuration and keep eMMC regulators soft-disabled
- add new exynos5250-spring DT
- cleanup exynos5250-arndale, exynos5250-smdk5250 and exynos5250-snow
- exynos5250-arndale: fix apparent GPIO typo and simplify USB3503
- exynos5250-snow and exynos Peach boards: add rtc_src clock for RTC
- correct mmc0 capability string exynos5420-peach-pit and exynos5800-
peach-pi
- exynos3250: add MFC codec nodes
- s3c64xx: enable PWM node by default
* tag 'samsung-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: add CPU nodes for Exynos4 SoCs
ARM: dts: add MFC codec device node for exynos3250
ARM: dts: Add Maxim 77693 PMIC to exynos4412-trats2
ARM: dts: Add sleep mode pin configuration for exynos4412-trats2
ARM: dts: Add utility macro to define pin sleep states for exynos4x12-pinctrl
ARM: dts: Keep eMMC regulators soft-disabled for exynos4412-trats2
ARM: dts: correct the mmc0 capability string for exynos Peach boards
ARM: dts: Add rtc_src clk for s3c-rtc on exynos5250-snow
ARM: dts: Add rtc_src clk for s3c-rtc on exynos Peach boards
ARM: dts: Enable PWM node by default for s3c64xx
ARM: dts: Add exynos5250-spring device tree
ARM: dts: Simplify USB3503 on exynos5250-arndale
ARM: dts: Fix apparent GPIO typo in exynos5250-arndale
ARM: dts: Clean up exynos5250-arndale
ARM: dts: Clean up exynos5250-smdk5250
ARM: dts: Fill in bootargs for exynos5250-snow
ARM: dts: Clean up exynos5250-snow
ARM: dts: Prepare node labels for exynos5250
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Looks like we have some GPMC NAND timings missing device
width. This fixes "gpmc_cs_program_settings: invalid width 0!"
errors during boot.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
With the GPMC warnings now enabled, I noticed the LAN9220 timings
can overflow the GPMC registers with 200MHz L3 speed. Earlier we
were just skipping the bad timings and would continue with the
bootloader timings. Now we no longer allow to continue with bad
timings as we have the timings in the .dts files.
We could start using the GPMC clock divider, but let's instead
use the u-boot timings that are known to be working and a bit
faster. These are basically the u-boot NET_GPMC_CONFIG[1-6]
defines deciphered. Except that we don't set gpmc,burst-length
as that's only partially configured and does not seem to work
if fully enabled.
[tony@atomide.com: updated to remove gpmc,burst-length]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add the missing CAN devices node including their pin muxing. The required
clock node already exists.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Add the missing CAN devices node including their pin muxing to the shared
.dtsi for at91sam9x5. Actually include this file.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
This patch adds usart dma definitions to both dtsi for sam9x5 chips. Without
usage of dma it's unable to catch all bytes on usart receiver.
Signed-off-by: Jiri Prchal <jiri.prchal@aksignal.cz>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
