| Age | Commit message (Collapse) | Author |
|---|
|
The clang-analyzer reports:
"Excessive padding in 'struct imx8m_blk_ctrl_domain_data'
(12 padding bytes, where 4 is optimal). Optimal fields order: name,
clk_names, path_names, gpc_name, num_clks, num_paths, rst_mask, clk_mask,
mipi_phy_rst_mask, consider reordering the fields or adding explicit
padding members [clang-analyzer-optin.performance.Padding]
struct imx8m_blk_ctrl_domain_data {"
So reordering the fields.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This is the lowest frequency supported by older iMX8MQ SoC
revisions.
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
According to imx8mq errata (ERR007805):
> To meet the clock low period requirement in fast speed mode,
> SCL must be configured to 384KHz or less.
Note that the imx i2c driver already implements this erratum and works
around it. This is only for the description to reflect reality.
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
0.8V is outside of the operating voltage specified for imx8mq, see
chapter 3.1.4 "Operating ranges" of the IMX8MDQLQCEC document.
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This reduces power consumption in system suspend by about 10%.
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Based on tests with my left ear (which appears to require lower levels
than the right one), one Birch, one Dogwood and three Evergreens.
It seems that the sensor reacts very weakly to hair, so let's make
the thresholds rather generous to compensate.
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
RS9116 card already limits itself to 50MHz by being a high-speed card,
while AP6275S can work at 100MHz just fine (technically it should work
at 200MHz as well since it's a SDR104 card, but it doesn't appear to be
the case in practice and further research will be needed to find out why).
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Userland needs the mount matrix to know the correct orientation of
the part.
Signed-off-by: Angus Ainslie <angus@akkea.ca>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
They're still in the operating range according to i.MX 8M Quad
datasheet. There's some headroom added over minimal values to
account for voltage drop.
Operational ranges (min - typ - max [selected]):
- VDD_SOC (BUCK1): 0.81 - 0.9 - 0.99 [0.88]
- VDD_ARM (BUCK2): 0.81 - 0.9 - 1.05 [0.84] (1000MHz)
0.90 - 1.0 - 1.05 [0.93] (1500MHz)
- VDD_GPU (BUCK3): 0.81 - 0.9 - 1.05 [0.85] (800MHz)
0.90 - 1.0 - 1.05 [ -- ] (1000MHz)
- VDD_VPU (BUCK4): 0.81 - 0.9 - 1.05 [ -- ] (550/500/588MHz)
0.90 - 1.0 - 1.05 [0.93] (660/600/800MHz)
Idle power consumption doesn't appear to be influenced much,
but a simple load test (`cat /dev/urandom | pigz - > /dev/null`
combined with running Animatch) seems to show about 0.3W of
difference.
Care is advised, as there may be differences between each
units in how low can they be undervolted - in my experience,
reaching that point usually makes the phone fail to boot.
In my case, it appears that my Birch phone can go down the most.
This is a somewhat conservative set of values that I've seen
working well on all my devices; I haven't tried very hard to
optimize it, so more experiments are welcome.
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Correctly set regulation-voltage, termination-current and charge-current
for the different librem 5 board revisions.
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add brightness-levels and default-brightness-level properties to
the librem5 board description that have been used for a long time.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
No functional change, but it describes the hardware better.
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Fix the regulator name for the audio-1v8 regulator.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The CLKO2 clock is used for both camera CSI interfaces as the
driving clock for the connected sensors. In order for it to be
available, use this hog. We can't simply add it to 2 different
sensor descriptions.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
No frames are streamed when using the default frequencies. I'm not yet
sure why the fastest ones don't work here but we've been using these
frequencies successfully for a long time now.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
devm_clk_get() can return -EPROBE_DEFER. So it is better to return the
error code from devm_clk_get(), instead of a hard coded -ENOENT.
This gives more opportunities to successfully probe the driver.
Fixes: 8959e5324485 ("regulator: fixed: add possibility to enable by clock")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/18459fae3d017a66313699c7c8456b28158b2dd0.1679819354.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
KASAN reported the following issue:
[ 36.825817][ T5923] BUG: KASAN: wild-memory-access in v9fs_get_acl+0x1a4/0x390
[ 36.827479][ T5923] Write of size 4 at addr 9fffeb37f97f1c00 by task syz-executor798/5923
[ 36.829303][ T5923]
[ 36.829846][ T5923] CPU: 0 PID: 5923 Comm: syz-executor798 Not tainted 6.2.0-syzkaller-18302-g596b6b709632 #0
[ 36.832110][ T5923] Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/21/2023
[ 36.834464][ T5923] Call trace:
[ 36.835196][ T5923] dump_backtrace+0x1c8/0x1f4
[ 36.836229][ T5923] show_stack+0x2c/0x3c
[ 36.837100][ T5923] dump_stack_lvl+0xd0/0x124
[ 36.838103][ T5923] print_report+0xe4/0x4c0
[ 36.839068][ T5923] kasan_report+0xd4/0x130
[ 36.840052][ T5923] kasan_check_range+0x264/0x2a4
[ 36.841199][ T5923] __kasan_check_write+0x2c/0x3c
[ 36.842216][ T5923] v9fs_get_acl+0x1a4/0x390
[ 36.843232][ T5923] v9fs_mount+0x77c/0xa5c
[ 36.844163][ T5923] legacy_get_tree+0xd4/0x16c
[ 36.845173][ T5923] vfs_get_tree+0x90/0x274
[ 36.846137][ T5923] do_new_mount+0x25c/0x8c8
[ 36.847066][ T5923] path_mount+0x590/0xe58
[ 36.848147][ T5923] __arm64_sys_mount+0x45c/0x594
[ 36.849273][ T5923] invoke_syscall+0x98/0x2c0
[ 36.850421][ T5923] el0_svc_common+0x138/0x258
[ 36.851397][ T5923] do_el0_svc+0x64/0x198
[ 36.852398][ T5923] el0_svc+0x58/0x168
[ 36.853224][ T5923] el0t_64_sync_handler+0x84/0xf0
[ 36.854293][ T5923] el0t_64_sync+0x190/0x194
Calling '__v9fs_get_acl' method in 'v9fs_get_acl' creates the
following chain of function calls:
__v9fs_get_acl
v9fs_fid_get_acl
v9fs_fid_xattr_get
p9_client_xattrwalk
Function p9_client_xattrwalk accepts a pointer to u64-typed
variable attr_size and puts some u64 value into it. However,
after the executing the p9_client_xattrwalk, in some circumstances
we assign the value of u64-typed variable 'attr_size' to the
variable 'retval', which we will return. However, the type of
'retval' is ssize_t, and if the value of attr_size is larger
than SSIZE_MAX, we will face the signed type overflow. If the
overflow occurs, the result of v9fs_fid_xattr_get may be
negative, but not classified as an error. When we try to allocate
an acl with 'broken' size we receive an error, but don't process
it. When we try to free this acl, we face the 'wild-memory-access'
error (because it wasn't allocated).
This patch will add new condition to the 'v9fs_fid_xattr_get'
function, so it will return an EOVERFLOW error if the 'attr_size'
is larger than SSIZE_MAX.
In this version of the patch I simplified the condition.
In previous (v2) version of the patch I removed explicit type conversion
and added separate condition to check the possible overflow and return
an error (in v1 version I've just modified the existing condition).
Tested via syzkaller.
Suggested-by: Christian Schoenebeck <linux_oss@crudebyte.com>
Reported-by: syzbot+cb1d16facb3cc90de5fb@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?id=fbbef66d9e4d096242f3617de5d14d12705b4659
Signed-off-by: Ivan Orlov <ivan.orlov0322@gmail.com>
Reviewed-by: Christian Schoenebeck <linux_oss@crudebyte.com>
Signed-off-by: Eric Van Hensbergen <ericvh@kernel.org>
|
|
The spi-max-frequency is a property of SPI children, not the
controller:
k210_generic.dtb: spi@50240000: Unevaluated properties are not allowed ('spi-max-frequency' was unexpected)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
Current code always maps MMIO devices as shared (decrypted) in a
confidential computing VM. But Hyper-V guest VMs on AMD SEV-SNP with vTOM
use a paravisor running in VMPL0 to emulate some devices, such as the
IO-APIC and TPM. In such a case, the device must be accessed as private
(encrypted) because the paravisor emulates the device at an address below
vTOM, where all accesses are encrypted.
Add a new hypervisor callback to determine if an MMIO address should
be mapped private. The callback allows hypervisor-specific code to handle
any quirks, the use of a paravisor, etc. in determining whether a mapping
must be private. If the callback is not used by a hypervisor, default
to returning "false", which is consistent with normal coco VM behavior.
Use this callback as another special case to check for when doing
ioremap(). Just checking the starting address is sufficient as an
ioremap range must be all private or all shared.
Also make the callback in early boot IO-APIC mapping code that uses the
fixmap.
[ bp: Touchups. ]
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/1678329614-3482-2-git-send-email-mikelley@microsoft.com
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt driver fixes from Greg KH:
"Here are a small set of USB and Thunderbolt driver fixes for reported
problems and a documentation update, for 6.3-rc4.
Included in here are:
- documentation update for uvc gadget driver
- small thunderbolt driver fixes
- cdns3 driver fixes
- dwc3 driver fixes
- dwc2 driver fixes
- chipidea driver fixes
- typec driver fixes
- onboard_usb_hub device id updates
- quirk updates
All of these have been in linux-next with no reported problems"
* tag 'usb-6.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (30 commits)
usb: dwc2: fix a race, don't power off/on phy for dual-role mode
usb: dwc2: fix a devres leak in hw_enable upon suspend resume
usb: chipidea: core: fix possible concurrent when switch role
usb: chipdea: core: fix return -EINVAL if request role is the same with current role
thunderbolt: Rename shadowed variables bit to interrupt_bit and auto_clear_bit
thunderbolt: Disable interrupt auto clear for rings
thunderbolt: Use const qualifier for `ring_interrupt_index`
usb: gadget: Use correct endianness of the wLength field for WebUSB
uas: Add US_FL_NO_REPORT_OPCODES for JMicron JMS583Gen 2
usb: cdnsp: changes PCI Device ID to fix conflict with CNDS3 driver
usb: cdns3: Fix issue with using incorrect PCI device function
usb: cdnsp: Fixes issue with redundant Status Stage
MAINTAINERS: make me a reviewer of USB/IP
thunderbolt: Use scale field when allocating USB3 bandwidth
thunderbolt: Limit USB3 bandwidth of certain Intel USB4 host routers
thunderbolt: Call tb_check_quirks() after initializing adapters
thunderbolt: Add missing UNSET_INBOUND_SBTX for retimer access
thunderbolt: Fix memory leak in margining
usb: dwc2: drd: fix inconsistent mode if role-switch-default-mode="host"
docs: usb: Add documentation for the UVC Gadget
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fix from Borislav Petkov:
- Fix a corner case where vruntime of a task is not being sanitized
* tag 'sched_urgent_for_v6.3_rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/fair: Sanitize vruntime of entity being migrated
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fix from Borislav Petkov:
- Properly clear perf event status tracking in the AMD perf event
overflow handler
* tag 'perf_urgent_for_v6.3_rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/amd/core: Always clear status for idx
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull core fixes from Borislav Petkov:
- Do the delayed RCU wakeup for kthreads in the proper order so that
former doesn't get ignored
- A noinstr warning fix
* tag 'core_urgent_for_v6.3_rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
entry/rcu: Check TIF_RESCHED _after_ delayed RCU wake-up
entry: Fix noinstr warning in __enter_from_user_mode()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Borislav Petkov:
- Add a AMX ptrace self test
- Prevent a false-positive warning when retrieving the (invalid)
address of dynamic FPU features in their init state which are not
saved in init_fpstate at all
- Randomize per-CPU entry areas only when KASLR is enabled
* tag 'x86_urgent_for_v6.3_rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
selftests/x86/amx: Add a ptrace test
x86/fpu/xstate: Prevent false-positive warning in __copy_xstate_uabi_buf()
x86/mm: Do not shuffle CPU entry areas without KASLR
|
|
Pull cifs client fixes from Steve French:
"Twelve cifs/smb3 client fixes (most also for stable)
- forced umount fix
- fix for two perf regressions
- reconnect fixes
- small debugging improvements
- multichannel fixes"
* tag 'smb3-client-fixes-6.3-rc3' of git://git.samba.org/sfrench/cifs-2.6:
smb3: fix unusable share after force unmount failure
cifs: fix dentry lookups in directory handle cache
smb3: lower default deferred close timeout to address perf regression
cifs: fix missing unload_nls() in smb2_reconnect()
cifs: avoid race conditions with parallel reconnects
cifs: append path to open_enter trace event
cifs: print session id while listing open files
cifs: dump pending mids for all channels in DebugData
cifs: empty interface list when server doesn't support query interfaces
cifs: do not poll server interfaces too regularly
cifs: lock chan_lock outside match_session
cifs: check only tcon status on tcon related functions
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux
Pull nfsd fix from Chuck Lever:
- Fix a crash when using NFS with krb5p
* tag 'nfsd-6.3-4' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux:
SUNRPC: Fix a crash in gss_krb5_checksum()
|
|
Pull yet more xfs bug fixes from Darrick Wong:
"The first bugfix addresses a longstanding problem where we use the
wrong file mapping cursors when trying to compute the speculative
preallocation quantity. This has been causing sporadic crashes when
alwayscow mode is engaged.
The other two fixes correct minor problems in more recent changes.
- Fix the new allocator tracepoints because git am mismerged the
changes such that the trace_XXX got rebased to be in function YYY
instead of XXX
- Ensure that the perag AGFL_RESET state is consistent with whatever
we've just read off the disk
- Fix a bug where we used the wrong iext cursor during a write begin"
* tag 'xfs-6.3-fixes-7' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: fix mismerged tracepoints
xfs: clear incore AGFL_RESET state if it's not needed
xfs: pass the correct cursor to xfs_iomap_prealloc_size
|
|
Pull xfs percpu counter fixes from Darrick Wong:
"We discovered a filesystem summary counter corruption problem that was
traced to cpu hot-remove racing with the call to percpu_counter_sum
that sets the free block count in the superblock when writing it to
disk. The root cause is that percpu_counter_sum doesn't cull from
dying cpus and hence misses those counter values if the cpu shutdown
hooks have not yet run to merge the values.
I'm hoping this is a fairly painless fix to the problem, since the
dying cpu mask should generally be empty. It's been in for-next for a
week without any complaints from the bots.
- Fix a race in the percpu counters summation code where the
summation failed to add in the values for any CPUs that were dying
but not yet dead. This fixes some minor discrepancies and incorrect
assertions when running generic/650"
* tag 'xfs-6.3-fixes-4' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
pcpcntr: remove percpu_counter_sum_all()
fork: remove use of percpu_counter_sum_all
pcpcntrs: fix dying cpu summation race
cpumask: introduce for_each_cpu_or
|
|
clang with W=1 reports
fs/ksmbd/unicode.c:122:19: error: unused function
'is_char_allowed' [-Werror,-Wunused-function]
static inline int is_char_allowed(char *ch)
^
This function is not used so remove it.
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Acked-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
Commit 83dcedd5540d ("ksmbd: fix infinite loop in ksmbd_conn_handler_loop()"),
changes GFP modifiers passed to kvmalloc(). This cause xfstests generic/551
test to fail. We limit pdu length size according to connection status and
maximum number of connections. In the rest, memory allocation of request
is limited by credit management. so these flags are no longer needed.
Fixes: 83dcedd5540d ("ksmbd: fix infinite loop in ksmbd_conn_handler_loop()")
Cc: stable@vger.kernel.org
Signed-off-by: Marios Makassikis <mmakassikis@freebox.fr>
Acked-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
Pull xfs fixes from Darrick Wong:
"This batch started with some debugging enhancements to the new
allocator refactoring that we put in 6.3-rc1 to assist developers in
rebasing their dev branches.
As for more serious code changes -- there's a bug fix to make the
lockless allocator scan the whole filesystem before resorting to the
locking allocator. We're also adding a selftest for the venerable
directory/xattr hash function to make sure that it produces consistent
results so that we can address any fallout as soon as possible.
- Add a few debugging assertions so that people (me) trying to port
code to the new allocator functions don't mess up the caller
requirements
- Relax some overly cautious lock ordering enforcement in the new
allocator code, which means that file allocations will locklessly
scan for the best space they can get before backing off to the
traditional lock-and-really-get-it behavior
- Add tracepoints to make it easier to trace the xfs allocator
behavior
- Actually test the dir/xattr hash algorithm to make sure it produces
consistent results across all the platforms XFS supports"
* tag 'xfs-6.3-fixes-3' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: test dir/attr hash when loading module
xfs: add tracepoints for each of the externally visible allocators
xfs: walk all AGs if TRYLOCK passed to xfs_alloc_vextent_iterate_ags
xfs: try to idiot-proof the allocators
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
- it87: Fix voltage scaling for chips with 10.9mV ADCs
- xgene: Fix ioremap and memremap leak
- peci/cputemp: Fix miscalculated DTS temperature for SKX
- hwmon core: fix potential sensor registration failure with thermal
subsystem if of_node is missing
* tag 'hwmon-for-v6.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon (it87): Fix voltage scaling for chips with 10.9mV ADCs
hwmon: (xgene) Fix ioremap and memremap leak
hwmon: fix potential sensor registration fail if of_node is missing
hwmon: (peci/cputemp) Fix miscalculated DTS for SKX
|
|
When link speed is 10 Mbps and temperature is under -20°C, RTL8168H and
RTL8107E may have rx crc error. Disable phy 10 Mbps pll off to fix this
issue.
Fixes: 6e1d0b898818 ("r8169:add support for RTL8168H and RTL8107E")
Signed-off-by: ChunHao Lin <hau@realtek.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Oleksij Rempel says:
====================
net: dsa: microchip: ksz8: fixes for stable
changes v2:
- use proper Fixes tag
- add Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com> on all
reviewed patches except the ksz8863_smi patch.
These fixes address issues such as incomplete FDB extraction, incorrect
FID extraction and configuration, incorrect timestamp extraction, and
ghost entry extraction from an empty dynamic MAC table. These updates
ensure proper functioning of the FDB/MDB functionality for the
ksz8863/ksz8873 series of chips.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
FID is directly mapped to VID. However, configuring a MAC address with a
VID != 0 resulted in incorrect configuration due to an incorrect bit
mask. This kernel commit fixed the issue by correcting the bit mask and
ensuring proper configuration of MAC addresses with non-zero VID.
Fixes: 4b20a07e103f ("net: dsa: microchip: ksz8795: add support for ksz88xx chips")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Current regmap bulk access is broken, resulting to wrong reads/writes
if ksz_read64/ksz_write64 functions are used.
Mostly this issue was visible by using ksz8_fdb_dump(), which returned
corrupt MAC address.
The reason is that regmap was configured to have max_raw_read/write,
even if ksz8863_mdio_read/write functions are able to handle unlimited
read/write accesses. On ksz_read64 function we are using multiple 32bit
accesses by incrementing each access by 1 instead of 4. Resulting buffer
had 01234567.12345678 instead of 01234567.89abcdef.
We have multiple ways to fix it:
- enable 4 byte alignment for 32bit accesses. Since the HW do not have
this requirement. It will break driver.
- disable max_raw_* limit.
This patch is removing max_raw_* limit for regmap accesses in ksz8863_smi.
Fixes: 60a364760002 ("net: dsa: microchip: Add Microchip KSZ8863 SMI based driver support")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
empty dynamic MAC table.
If the dynamic MAC table is empty, we will still extract one outdated
entry. Fix it by using correct bit offset.
Fixes: 4b20a07e103f ("net: dsa: microchip: ksz8795: add support for ksz88xx chips")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We are using wrong offset, so we will get not a timestamp.
Fixes: 4b20a07e103f ("net: dsa: microchip: ksz8795: add support for ksz88xx chips")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Current ksz8_fdb_dump() is able to extract only max 249 entries on
the ksz8863/ksz8873 series of switches. This happened due to wrong
bit mask and offset calculation.
This commit corrects the issue and allows for the complete extraction of
all 1024 entries.
Fixes: 4b20a07e103f ("net: dsa: microchip: ksz8795: add support for ksz88xx chips")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before this patch, the ksz8_fdb_dump() function had several issues, such
as uninitialized variables and incorrect usage of source port as a bit
mask. These problems caused inaccurate reporting of vid information and
port assignment in the bridge fdb.
Fixes: e587be759e6e ("net: dsa: microchip: update fdb add/del/dump in ksz_common")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Driver has IO wrappers but xlnx_pr_decouple_read() is not used and readl is
used instead which is just wrong.
It is also generating sparse issue that xlnx_pr_decouple_read() is unused.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Tom Rix <trix@redhat.com>
Acked-by: Xu Yilun <yilun.xu@intel.com>
Link: https://lore.kernel.org/r/0381e4e8061c2fee182a104768e84feff3a82d25.1679412800.git.michal.simek@amd.com
Signed-off-by: Xu Yilun <yilun.xu@intel.com>
|
|
Smatch complains that:
drivers/ptp/ptp_qoriq.c ptp_qoriq_probe()
warn: 'base' from ioremap() not released.
Fix this by revising the parameter from 'ptp_qoriq->base' to 'base'.
This is only a bug if ptp_qoriq_init() returns on the
first -ENODEV error path.
For other error paths ptp_qoriq->base and base are the same.
And this change makes the code more readable.
Fixes: 7f4399ba405b ("ptp_qoriq: fix NULL access if ptp dt node missing")
Signed-off-by: SongJingyi <u201912584@hust.edu.cn>
Reviewed-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Link: https://lore.kernel.org/r/20230324031406.1895159-1-u201912584@hust.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, vmxnet3 uses GRO callback only if LRO is disabled. However,
on smartNic based setups where UPT is supported, LRO can be enabled
from guest VM but UPT devicve does not support LRO as of now. In such
cases, there can be performance degradation as GRO is not being done.
This patch fixes this issue by calling GRO API when UPT is enabled. We
use updateRxProd to determine if UPT mode is active or not.
To clarify few things discussed over the thread:
The patch is not neglecting any feature bits nor disabling GRO. It uses
GRO callback when UPT is active as LRO is not available in UPT.
GRO callback cannot be used as default for all cases as it degrades
performance for non-UPT cases or for cases when LRO is already done in
ESXi.
Cc: stable@vger.kernel.org
Fixes: 6f91f4ba046e ("vmxnet3: add support for capability registers")
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230323200721.27622-1-doshir@vmware.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The probe function sets priv->chip_data to (void *)priv + sizeof(*priv)
with the expectation that priv has enough trailing space.
However, only realtek-smi actually allocated this chip_data space.
Do likewise in realtek-mdio to fix out-of-bounds accesses.
These accesses likely went unnoticed so far, because of an (unused)
buf[4096] member in struct realtek_priv, which caused kmalloc to
round up the allocated buffer to a big enough size, so nothing of
value was overwritten. With a different allocator (like in the barebox
bootloader port of the driver) or with KASAN, the memory corruption
becomes quickly apparent.
Fixes: aac94001067d ("net: dsa: realtek: add new mdio interface for drivers")
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Link: https://lore.kernel.org/r/20230323103735.2331786-1-a.fatoum@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
_base_allocate_sense_dma_pool() already prints out the sense pool
information, so don't print it a second time after calling it in
_base_allocate_memory_pools(). In addition the version in
_base_allocate_memory_pools() was using the wrong size value, sz, which was
last assigned when doing some nvme calculations instead of sense_sz to
determine the pool size in kilobytes.
Cc: Sathya Prakash <sathya.prakash@broadcom.com>
Cc: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Cc: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>
Cc: MPT-FusionLinux.pdl@broadcom.com
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Fixes: 970ac2bb70e7 ("scsi: mpt3sas: Force sense buffer allocations to be within same 4 GB region")
Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com>
Link: https://lore.kernel.org/r/20230324193204.567932-1-jsnitsel@redhat.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc fixes from Andrew Morton:
"21 hotfixes, 8 of which are cc:stable. 11 are for MM, the remainder
are for other subsystems"
* tag 'mm-hotfixes-stable-2023-03-24-17-09' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (21 commits)
mm: mmap: remove newline at the end of the trace
mailmap: add entries for Richard Leitner
kcsan: avoid passing -g for test
kfence: avoid passing -g for test
mm: kfence: fix using kfence_metadata without initialization in show_object()
lib: dhry: fix unstable smp_processor_id(_) usage
mailmap: add entry for Enric Balletbo i Serra
mailmap: map Sai Prakash Ranjan's old address to his current one
mailmap: map Rajendra Nayak's old address to his current one
Revert "kasan: drop skip_kasan_poison variable in free_pages_prepare"
mailmap: add entry for Tobias Klauser
kasan, powerpc: don't rename memintrinsics if compiler adds prefixes
mm/ksm: fix race with VMA iteration and mm_struct teardown
kselftest: vm: fix unused variable warning
mm: fix error handling for map_deny_write_exec
mm: deduplicate error handling for map_deny_write_exec
checksyscalls: ignore fstat to silence build warning on LoongArch
nilfs2: fix kernel-infoleak in nilfs_ioctl_wrap_copy()
test_maple_tree: add more testing for mas_empty_area()
maple_tree: fix mas_skip_node() end slot detection
...
|
|
Some USB-SATA adapters have broken behavior when an unsupported VPD page is
probed: Depending on the VPD page number, a 4-byte header with a valid VPD
page number but with a 0 length is returned. Currently, scsi_vpd_inquiry()
only checks that the page number is valid to determine if the page is
valid, which results in receiving only the 4-byte header for the
non-existent page. This error manifests itself very often with page 0xb9
for the Concurrent Positioning Ranges detection done by sd_read_cpr(),
resulting in the following error message:
sd 0:0:0:0: [sda] Invalid Concurrent Positioning Ranges VPD page
Prevent such misleading error message by adding a check in
scsi_vpd_inquiry() to verify that the page length is not 0.
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Link: https://lore.kernel.org/r/20230322022211.116327-1-damien.lemoal@opensource.wdc.com
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Pull ksmbd server fixes from Steve French:
- return less confusing messages on unsupported dialects
(STATUS_NOT_SUPPORTED instead of I/O error)
- fix for overly frequent inactive session termination
- fix refcount leak
- fix bounds check problems found by static checkers
- fix to advertise named stream support correctly
- Fix AES256 signing bug when connected to from MacOS
* tag '6.3-rc3-ksmbd-smb3-server-fixes' of git://git.samba.org/ksmbd:
ksmbd: return unsupported error on smb1 mount
ksmbd: return STATUS_NOT_SUPPORTED on unsupported smb2.0 dialect
ksmbd: don't terminate inactive sessions after a few seconds
ksmbd: fix possible refcount leak in smb2_open()
ksmbd: add low bound validation to FSCTL_QUERY_ALLOCATED_RANGES
ksmbd: add low bound validation to FSCTL_SET_ZERO_DATA
ksmbd: set FILE_NAMED_STREAMS attribute in FS_ATTRIBUTE_INFORMATION
ksmbd: fix wrong signingkey creation when encryption is AES256
|
|
When a physical disk is attached directly "without JBOD MAP support" (see
megasas_get_tm_devhandle()) then there is no real error handling in the
driver. Return FAILED instead of SUCCESS.
Fixes: 18365b138508 ("megaraid_sas: Task management support")
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Link: https://lore.kernel.org/r/20230324150134.14696-1-thenzl@redhat.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
