summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2024-10-08e1000e: change I219 (19) devices to ADPVitaly Lifshits
Sporadic issues, such as PHY access loss, have been observed on I219 (19) devices. It was found that these devices have hardware more closely related to ADP than MTP and the issues were caused by taking MTP-specific flows. Change the MAC and board types of these devices from MTP to ADP to correctly reflect the LAN hardware, and flows, of these devices. Fixes: db2d737d63c5 ("e1000e: Separate MTP board type from ADP") Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com> Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-10-08igb: Do not bring the device up after non-fatal errorMohamed Khalfella
Commit 004d25060c78 ("igb: Fix igb_down hung on surprise removal") changed igb_io_error_detected() to ignore non-fatal pcie errors in order to avoid hung task that can happen when igb_down() is called multiple times. This caused an issue when processing transient non-fatal errors. igb_io_resume(), which is called after igb_io_error_detected(), assumes that device is brought down by igb_io_error_detected() if the interface is up. This resulted in panic with stacktrace below. [ T3256] igb 0000:09:00.0 haeth0: igb: haeth0 NIC Link is Down [ T292] pcieport 0000:00:1c.5: AER: Uncorrected (Non-Fatal) error received: 0000:09:00.0 [ T292] igb 0000:09:00.0: PCIe Bus Error: severity=Uncorrected (Non-Fatal), type=Transaction Layer, (Requester ID) [ T292] igb 0000:09:00.0: device [8086:1537] error status/mask=00004000/00000000 [ T292] igb 0000:09:00.0: [14] CmpltTO [ 200.105524,009][ T292] igb 0000:09:00.0: AER: TLP Header: 00000000 00000000 00000000 00000000 [ T292] pcieport 0000:00:1c.5: AER: broadcast error_detected message [ T292] igb 0000:09:00.0: Non-correctable non-fatal error reported. [ T292] pcieport 0000:00:1c.5: AER: broadcast mmio_enabled message [ T292] pcieport 0000:00:1c.5: AER: broadcast resume message [ T292] ------------[ cut here ]------------ [ T292] kernel BUG at net/core/dev.c:6539! [ T292] invalid opcode: 0000 [#1] PREEMPT SMP [ T292] RIP: 0010:napi_enable+0x37/0x40 [ T292] Call Trace: [ T292] <TASK> [ T292] ? die+0x33/0x90 [ T292] ? do_trap+0xdc/0x110 [ T292] ? napi_enable+0x37/0x40 [ T292] ? do_error_trap+0x70/0xb0 [ T292] ? napi_enable+0x37/0x40 [ T292] ? napi_enable+0x37/0x40 [ T292] ? exc_invalid_op+0x4e/0x70 [ T292] ? napi_enable+0x37/0x40 [ T292] ? asm_exc_invalid_op+0x16/0x20 [ T292] ? napi_enable+0x37/0x40 [ T292] igb_up+0x41/0x150 [ T292] igb_io_resume+0x25/0x70 [ T292] report_resume+0x54/0x70 [ T292] ? report_frozen_detected+0x20/0x20 [ T292] pci_walk_bus+0x6c/0x90 [ T292] ? aer_print_port_info+0xa0/0xa0 [ T292] pcie_do_recovery+0x22f/0x380 [ T292] aer_process_err_devices+0x110/0x160 [ T292] aer_isr+0x1c1/0x1e0 [ T292] ? disable_irq_nosync+0x10/0x10 [ T292] irq_thread_fn+0x1a/0x60 [ T292] irq_thread+0xe3/0x1a0 [ T292] ? irq_set_affinity_notifier+0x120/0x120 [ T292] ? irq_affinity_notify+0x100/0x100 [ T292] kthread+0xe2/0x110 [ T292] ? kthread_complete_and_exit+0x20/0x20 [ T292] ret_from_fork+0x2d/0x50 [ T292] ? kthread_complete_and_exit+0x20/0x20 [ T292] ret_from_fork_asm+0x11/0x20 [ T292] </TASK> To fix this issue igb_io_resume() checks if the interface is running and the device is not down this means igb_io_error_detected() did not bring the device down and there is no need to bring it up. Signed-off-by: Mohamed Khalfella <mkhalfella@purestorage.com> Reviewed-by: Yuanyuan Zhong <yzhong@purestorage.com> Fixes: 004d25060c78 ("igb: Fix igb_down hung on surprise removal") Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-10-08i40e: Fix macvlan leak by synchronizing access to mac_filter_hashAleksandr Loktionov
This patch addresses a macvlan leak issue in the i40e driver caused by concurrent access to vsi->mac_filter_hash. The leak occurs when multiple threads attempt to modify the mac_filter_hash simultaneously, leading to inconsistent state and potential memory leaks. To fix this, we now wrap the calls to i40e_del_mac_filter() and zeroing vf->default_lan_addr.addr with spin_lock/unlock_bh(&vsi->mac_filter_hash_lock), ensuring atomic operations and preventing concurrent access. Additionally, we add lockdep_assert_held(&vsi->mac_filter_hash_lock) in i40e_add_mac_filter() to help catch similar issues in the future. Reproduction steps: 1. Spawn VFs and configure port vlan on them. 2. Trigger concurrent macvlan operations (e.g., adding and deleting portvlan and/or mac filters). 3. Observe the potential memory leak and inconsistent state in the mac_filter_hash. This synchronization ensures the integrity of the mac_filter_hash and prevents the described leak. Fixes: fed0d9f13266 ("i40e: Fix VF's MAC Address change on VM") Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com> Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-10-08selftests: vDSO: improve getrandom and chacha error messagesJason A. Donenfeld
Improve the error and skip condition messages to let the developer know precisely where a test has failed. Also make better use of the ksft api for this. Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
2024-10-08selftests: vDSO: unconditionally build getrandom testJason A. Donenfeld
Rather than building on supported archs, build on all archs, and then use the presence of the symbol in the vDSO to either skip the test or move forward with it. Note that this means that this test no longer checks whether the symbol was correctly added to the kernel. But hopefully this will be clear enough to developers and we'll cross our fingers that symbols aren't removed by accident and not caught after this change. Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
2024-10-08selftests: vDSO: unconditionally build chacha testJason A. Donenfeld
Rather than using symlinks to find the vgetrandom-chacha.S file for each arch, store this in a file that uses the compiler to determine architecture, and then make use of weak symbols to skip the test on architectures that don't provide the code. Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
2024-10-08ice: Fix increasing MSI-X on VFMarcin Szycik
Increasing MSI-X value on a VF leads to invalid memory operations. This is caused by not reallocating some arrays. Reproducer: modprobe ice echo 0 > /sys/bus/pci/devices/$PF_PCI/sriov_drivers_autoprobe echo 1 > /sys/bus/pci/devices/$PF_PCI/sriov_numvfs echo 17 > /sys/bus/pci/devices/$VF0_PCI/sriov_vf_msix_count Default MSI-X is 16, so 17 and above triggers this issue. KASAN reports: BUG: KASAN: slab-out-of-bounds in ice_vsi_alloc_ring_stats+0x38d/0x4b0 [ice] Read of size 8 at addr ffff8888b937d180 by task bash/28433 (...) Call Trace: (...) ? ice_vsi_alloc_ring_stats+0x38d/0x4b0 [ice] kasan_report+0xed/0x120 ? ice_vsi_alloc_ring_stats+0x38d/0x4b0 [ice] ice_vsi_alloc_ring_stats+0x38d/0x4b0 [ice] ice_vsi_cfg_def+0x3360/0x4770 [ice] ? mutex_unlock+0x83/0xd0 ? __pfx_ice_vsi_cfg_def+0x10/0x10 [ice] ? __pfx_ice_remove_vsi_lkup_fltr+0x10/0x10 [ice] ice_vsi_cfg+0x7f/0x3b0 [ice] ice_vf_reconfig_vsi+0x114/0x210 [ice] ice_sriov_set_msix_vec_count+0x3d0/0x960 [ice] sriov_vf_msix_count_store+0x21c/0x300 (...) Allocated by task 28201: (...) ice_vsi_cfg_def+0x1c8e/0x4770 [ice] ice_vsi_cfg+0x7f/0x3b0 [ice] ice_vsi_setup+0x179/0xa30 [ice] ice_sriov_configure+0xcaa/0x1520 [ice] sriov_numvfs_store+0x212/0x390 (...) To fix it, use ice_vsi_rebuild() instead of ice_vf_reconfig_vsi(). This causes the required arrays to be reallocated taking the new queue count into account (ice_vsi_realloc_stat_arrays()). Set req_txq and req_rxq before ice_vsi_rebuild(), so that realloc uses the newly set queue count. Additionally, ice_vsi_rebuild() does not remove VSI filters (ice_fltr_remove_all()), so ice_vf_init_host_cfg() is no longer necessary. Reported-by: Jacob Keller <jacob.e.keller@intel.com> Fixes: 2a2cb4c6c181 ("ice: replace ice_vf_recreate_vsi() with ice_vf_reconfig_vsi()") Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-10-08ice: Flush FDB entries before resetWojciech Drewek
Triggering the reset while in switchdev mode causes errors[1]. Rules are already removed by this time because switch content is flushed in case of the reset. This means that rules were deleted from HW but SW still thinks they exist so when we get SWITCHDEV_FDB_DEL_TO_DEVICE notification we try to delete not existing rule. We can avoid these errors by clearing the rules early in the reset flow before they are removed from HW. Switchdev API will get notified that the rule was removed so we won't get SWITCHDEV_FDB_DEL_TO_DEVICE notification. Remove unnecessary ice_clear_sw_switch_recipes. [1] ice 0000:01:00.0: Failed to delete FDB forward rule, err: -2 ice 0000:01:00.0: Failed to delete FDB guard rule, err: -2 Fixes: 7c945a1a8e5f ("ice: Switchdev FDB events support") Reviewed-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com> Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com> Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-10-08ice: Fix netif_is_ice() in Safe ModeMarcin Szycik
netif_is_ice() works by checking the pointer to netdev ops. However, it only checks for the default ice_netdev_ops, not ice_netdev_safe_mode_ops, so in Safe Mode it always returns false, which is unintuitive. While it doesn't look like netif_is_ice() is currently being called anywhere in Safe Mode, this could change and potentially lead to unexpected behaviour. Fixes: df006dd4b1dc ("ice: Add initial support framework for LAG") Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com> Reviewed-by: Brett Creeley <brett.creeley@amd.com> Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-10-08ice: Fix entering Safe ModeMarcin Szycik
If DDP package is missing or corrupted, the driver should enter Safe Mode. Instead, an error is returned and probe fails. To fix this, don't exit init if ice_init_ddp_config() returns an error. Repro: * Remove or rename DDP package (/lib/firmware/intel/ice/ddp/ice.pkg) * Load ice Fixes: cc5776fe1832 ("ice: Enable switching default Tx scheduler topology") Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com> Reviewed-by: Brett Creeley <brett.creeley@amd.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-10-08nvme: delete unnecessary fallthru commentTokunori Ikegami
Signed-off-by: Tokunori Ikegami <ikegami.t@gmail.com> Signed-off-by: Keith Busch <kbusch@kernel.org>
2024-10-08nvmet-rdma: use sbitmap to replace rsp free listGuixin Liu
We can use sbitmap to manage all the nvmet_rdma_rsp instead of using free lists and spinlock, and we can use an additional tag to determine whether the nvmet_rdma_rsp is extra allocated. In addition, performance has improved: 1. testing environment is local rxe rdma devie and mem-based backstore device. 2. fio command, test the average 5 times: fio -filename=/dev/nvme0n1 --ioengine=libaio -direct=1 -size=1G -name=1 -thread -runtime=60 -time_based -rw=read -numjobs=16 -iodepth=128 -bs=4k -group_reporting 3. Before: 241k IOPS, After: 256k IOPS, an increase of about 5%. Signed-off-by: Guixin Liu <kanie@linux.alibaba.com> Reviewed-by: Jens Axboe <axboe@kernel.dk>
2024-10-08Merge tag 'sched_ext-for-6.12-rc2-fixes' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tj/sched_ext Pull sched_ext fixes from Tejun Heo: - ops.enqueue() didn't have a way to tell whether select_task_rq_scx() and thus ops.select() were skipped. Some schedulers were incorrectly using SCX_ENQ_WAKEUP. Add SCX_ENQ_CPU_SELECTED and fix scx_qmap using it. - Remove a spurious WARN_ON_ONCE() in scx_cgroup_exit() - Fix error information clobbering during load - Add missing __weak markers to BPF helper declarations - Doc update * tag 'sched_ext-for-6.12-rc2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/sched_ext: sched_ext: Documentation: Update instructions for running example schedulers sched_ext, scx_qmap: Add and use SCX_ENQ_CPU_SELECTED sched/core: Add ENQUEUE_RQ_SELECTED to indicate whether ->select_task_rq() was called sched/core: Make select_task_rq() take the pointer to wake_flags instead of value sched_ext: scx_cgroup_exit() may be called without successful scx_cgroup_init() sched_ext: Improve error reporting during loading sched_ext: Add __weak markers to BPF helper function decalarations
2024-10-08bpf, lsm: Remove bpf_lsm_key_free hookThomas Weißschuh
The key_free LSM hook has been removed. Remove the corresponding BPF hook. Avoid warnings during the build: BTFIDS vmlinux WARN: resolve_btfids: unresolved symbol bpf_lsm_key_free Fixes: 5f8d28f6d7d5 ("lsm: infrastructure management of the key security blob") Signed-off-by: Thomas Weißschuh <linux@weissschuh.net> Signed-off-by: Andrii Nakryiko <andrii@kernel.org> Acked-by: Song Liu <song@kernel.org> Acked-by: Jiri Olsa <jolsa@kernel.org> Link: https://lore.kernel.org/bpf/20241005-lsm-key_free-v1-1-42ea801dbd63@weissschuh.net
2024-10-08fbdev: Switch back to struct platform_driver::remove()Uwe Kleine-König
After commit 0edb555a65d1 ("platform: Make platform_driver::remove() return void") .remove() is (again) the right callback to implement for platform drivers. Convert all platform drivers below drivers/video/fbdev to use .remove(), with the eventual goal to drop struct platform_driver::remove_new(). As .remove() and .remove_new() have the same prototypes, conversion is done by just changing the structure member name in the driver initializer. While touching these files, make indention of the struct initializer consistent in several files. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com> Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de> Signed-off-by: Helge Deller <deller@gmx.de>
2024-10-08thermal: intel: int340x: processor: Add MMIO RAPL PL4 supportZhang Rui
Similar to the MSR RAPL interface, MMIO RAPL supports PL4 too, so add MMIO RAPL PL4d support to the processor_thermal driver. As a result, the powercap sysfs for MMIO RAPL will show a new "peak power" constraint. Signed-off-by: Zhang Rui <rui.zhang@intel.com> Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Link: https://patch.msgid.link/20240930081801.28502-7-rui.zhang@intel.com [ rjw: Subject and changelog edits ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2024-10-08thermal: intel: int340x: processor: Remove MMIO RAPL CPU hotplug supportZhang Rui
CPU0/package0 is always online and the MMIO RAPL driver runs on single package systems only, so there is no need to handle CPU hotplug in it. Always register a RAPL package device for package 0 and remove the unnecessary CPU hotplug support. Signed-off-by: Zhang Rui <rui.zhang@intel.com> Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Link: https://patch.msgid.link/20240930081801.28502-6-rui.zhang@intel.com [ rjw: Subject edits ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2024-10-08powercap: intel_rapl_msr: Add PL4 support for Arrowlake-USumeet Pawnikar
Add PL4 support for ArrowLake-U platform. Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com> Signed-off-by: Zhang Rui <rui.zhang@intel.com> Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Link: https://patch.msgid.link/20240930081801.28502-5-rui.zhang@intel.com Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2024-10-08powercap: intel_rapl_tpmi: Ignore minor version changeZhang Rui
The hardware definition of every TPMI feature contains a major and minor version. When there is a change in the MMIO offset or change in the definition of a field, hardware will change major version. For addition of new fields without modifying existing MMIO offsets or fields, only the minor version is changed. If the driver has not been updated to recognize a new hardware major version, it cannot provide the RAPL interface to users due to possible register layout incompatibilities. However, the driver does not need to be updated every time the hardware minor version changes because in that case it will just miss some new functionality exposed by the hardware. The current implementation causes the driver to refuse to work for any hardware version change which is unnecessarily restrictive. If there is a minor version mismatch, log an information message and continue, but if there is a major version mismatch, log a warning and exit (as before). Signed-off-by: Zhang Rui <rui.zhang@intel.com> Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Link: https://patch.msgid.link/20240930081801.28502-4-rui.zhang@intel.com Fixes: 9eef7f9da928 ("powercap: intel_rapl: Introduce RAPL TPMI interface driver") [ rjw: Changelog edits ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2024-10-08x86/resctrl: Annotate get_mem_config() functions as __initNathan Chancellor
After a recent LLVM change [1] that deduces __cold on functions that only call cold code (such as __init functions), there is a section mismatch warning from __get_mem_config_intel(), which got moved to .text.unlikely. as a result of that optimization: WARNING: modpost: vmlinux: section mismatch in reference: \ __get_mem_config_intel+0x77 (section: .text.unlikely.) -> thread_throttle_mode_init (section: .init.text) Mark __get_mem_config_intel() as __init as well since it is only called from __init code, which clears up the warning. While __rdt_get_mem_config_amd() does not exhibit a warning because it does not call any __init code, it is a similar function that is only called from __init code like __get_mem_config_intel(), so mark it __init as well to keep the code symmetrical. CONFIG_SECTION_MISMATCH_WARN_ONLY=n would turn this into a fatal error. Fixes: 05b93417ce5b ("x86/intel_rdt/mba: Add primary support for Memory Bandwidth Allocation (MBA)") Fixes: 4d05bf71f157 ("x86/resctrl: Introduce AMD QOS feature") Signed-off-by: Nathan Chancellor <nathan@kernel.org> Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de> Reviewed-by: Reinette Chatre <reinette.chatre@intel.com> Cc: <stable@kernel.org> Link: https://github.com/llvm/llvm-project/commit/6b11573b8c5e3d36beee099dbe7347c2a007bf53 [1] Link: https://lore.kernel.org/r/20240917-x86-restctrl-get_mem_config_intel-init-v3-1-10d521256284@kernel.org
2024-10-08sched_ext: Documentation: Update instructions for running example schedulersDevaansh-Kumar
Since the artifact paths for tools changed, we need to update the documentation to reflect that path. Signed-off-by: Devaansh-Kumar <devaanshk840@gmail.com> Signed-off-by: Tejun Heo <tj@kernel.org>
2024-10-08Merge tag 'ntfs3_for_6.12' of ↵Linus Torvalds
https://github.com/Paragon-Software-Group/linux-ntfs3 Pull ntfs3 updates from Konstantin Komarov: "New: - implement fallocate for compressed files - add support for the compression attribute - optimize large writes to sparse files Fixes: - fix several potential deadlock scenarios - fix various internal bugs detected by syzbot - add checks before accessing NTFS structures during parsing - correct the format of output messages Refactoring: - replace fsparam_flag_no with fsparam_flag in options parser - remove unused functions and macros" * tag 'ntfs3_for_6.12' of https://github.com/Paragon-Software-Group/linux-ntfs3: (25 commits) fs/ntfs3: Format output messages like others fs in kernel fs/ntfs3: Additional check in ntfs_file_release fs/ntfs3: Fix general protection fault in run_is_mapped_full fs/ntfs3: Sequential field availability check in mi_enum_attr() fs/ntfs3: Additional check in ni_clear() fs/ntfs3: Fix possible deadlock in mi_read ntfs3: Change to non-blocking allocation in ntfs_d_hash fs/ntfs3: Remove unused al_delete_le fs/ntfs3: Rename ntfs3_setattr into ntfs_setattr fs/ntfs3: Replace fsparam_flag_no -> fsparam_flag fs/ntfs3: Add support for the compression attribute fs/ntfs3: Implement fallocate for compressed files fs/ntfs3: Make checks in run_unpack more clear fs/ntfs3: Add rough attr alloc_size check fs/ntfs3: Stale inode instead of bad fs/ntfs3: Refactor enum_rstbl to suppress static checker fs/ntfs3: Fix sparse warning in ni_fiemap fs/ntfs3: Fix warning possible deadlock in ntfs_set_state fs/ntfs3: Fix sparse warning for bigendian fs/ntfs3: Separete common code for file_read/write iter/splice ...
2024-10-08Merge tag 'perf-tools-fixes-for-v6.12-1-2024-10-08' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/perf/perf-tools Pull perf tools fixes from Arnaldo Carvalho de Melo: - Fix an assert() to handle captured and unprocessed ARM CoreSight CPU traces - Fix static build compilation error when libdw isn't installed or is too old - Add missing include when building with !HAVE_DWARF_GETLOCATIONS_SUPPORT - Add missing refcount put on 32-bit DSOs - Fix disassembly of user space binaries by setting the binary_type of DSO when loading - Update headers with the kernel sources, including asound.h, sched.h, fcntl, msr-index.h, irq_vectors.h, socket.h, list_sort.c and arm64's cputype.h * tag 'perf-tools-fixes-for-v6.12-1-2024-10-08' of git://git.kernel.org/pub/scm/linux/kernel/git/perf/perf-tools: perf cs-etm: Fix the assert() to handle captured and unprocessed cpu trace perf build: Fix build feature-dwarf_getlocations fail for old libdw perf build: Fix static compilation error when libdw is not installed perf dwarf-aux: Fix build with !HAVE_DWARF_GETLOCATIONS_SUPPORT tools headers arm64: Sync arm64's cputype.h with the kernel sources perf tools: Cope with differences for lib/list_sort.c copy from the kernel tools check_headers.sh: Add check variant that excludes some hunks perf beauty: Update copy of linux/socket.h with the kernel sources tools headers UAPI: Sync the linux/in.h with the kernel sources perf trace beauty: Update the arch/x86/include/asm/irq_vectors.h copy with the kernel sources tools arch x86: Sync the msr-index.h copy with the kernel sources tools include UAPI: Sync linux/fcntl.h copy with the kernel sources tools include UAPI: Sync linux/sched.h copy with the kernel sources tools include UAPI: Sync sound/asound.h copy with the kernel sources perf vdso: Missed put on 32-bit dsos perf symbol: Set binary_type of dso when loading
2024-10-08iommu/arm-smmu-v3: Convert comma to semicolonChen Ni
Replace comma between expressions with semicolons. Using a ',' in place of a ';' can have unintended side effects. Although that is not the case here, it is seems best to use ';' unless ',' is intended. Found by inspection. No functional change intended. Compile tested only. Fixes: e3b1be2e73db ("iommu/arm-smmu-v3: Reorganize struct arm_smmu_ctx_desc_cfg") Signed-off-by: Chen Ni <nichen@iscas.ac.cn> Reviewed-by: Jason Gunthorpe <jgg@nvidia.com> Reviewed-by: Lu Baolu <baolu.lu@linux.intel.com> Link: https://lore.kernel.org/r/20240923021557.3432068-1-nichen@iscas.ac.cn Signed-off-by: Will Deacon <will@kernel.org>
2024-10-08iommu/arm-smmu-v3: Fix last_sid_idx calculation for sid_bits==32Daniel Mentz
The function arm_smmu_init_strtab_2lvl uses the expression ((1 << smmu->sid_bits) - 1) to calculate the largest StreamID value. However, this fails for the maximum allowed value of SMMU_IDR1.SIDSIZE which is 32. The C standard states: "If the value of the right operand is negative or is greater than or equal to the width of the promoted left operand, the behavior is undefined." With smmu->sid_bits being 32, the prerequisites for undefined behavior are met. We observed that the value of (1 << 32) is 1 and not 0 as we initially expected. Similar bit shift operations in arm_smmu_init_strtab_linear seem to not be affected, because it appears to be unlikely for an SMMU to have SMMU_IDR1.SIDSIZE set to 32 but then not support 2-level Stream tables This issue was found by Ryan Huang <tzukui@google.com> on our team. Fixes: ce410410f1a7 ("iommu/arm-smmu-v3: Add arm_smmu_strtab_l1/2_idx()") Signed-off-by: Daniel Mentz <danielmentz@google.com> Link: https://lore.kernel.org/r/20241002015357.1766934-1-danielmentz@google.com Signed-off-by: Will Deacon <will@kernel.org>
2024-10-08iommu/arm-smmu: Clarify MMU-500 CPRE workaroundRobin Murphy
CPRE workarounds are implicated in at least 5 MMU-500 errata, some of which remain unfixed. The comment and warning message have proven to be unhelpfully misleading about this scope, so reword them to get the point across with less risk of going out of date or confusing users. Signed-off-by: Robin Murphy <robin.murphy@arm.com> Link: https://lore.kernel.org/r/dfa82171b5248ad7cf1f25592101a6eec36b8c9a.1728400877.git.robin.murphy@arm.com Signed-off-by: Will Deacon <will@kernel.org>
2024-10-08irqchip/sifive-plic: Unmask interrupt in plic_irq_enable()Nam Cao
It is possible that an interrupt is disabled and masked at the same time. When the interrupt is enabled again by enable_irq(), only plic_irq_enable() is called, not plic_irq_unmask(). The interrupt remains masked and never raises. An example where interrupt is both disabled and masked is when handle_fasteoi_irq() is the handler, and IRQS_ONESHOT is set. The interrupt handler: 1. Mask the interrupt 2. Handle the interrupt 3. Check if interrupt is still enabled, and unmask it (see cond_unmask_eoi_irq()) If another task disables the interrupt in the middle of the above steps, the interrupt will not get unmasked, and will remain masked when it is enabled in the future. The problem is occasionally observed when PREEMPT_RT is enabled, because PREEMPT_RT adds the IRQS_ONESHOT flag. But PREEMPT_RT only makes the problem more likely to appear, the bug has been around since commit a1706a1c5062 ("irqchip/sifive-plic: Separate the enable and mask operations"). Fix it by unmasking interrupt in plic_irq_enable(). Fixes: a1706a1c5062 ("irqchip/sifive-plic: Separate the enable and mask operations") Signed-off-by: Nam Cao <namcao@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/all/20241003084152.2422969-1-namcao@linutronix.de
2024-10-08irqchip/gic-v4: Don't allow a VMOVP on a dying VPEMarc Zyngier
Kunkun Jiang reported that there is a small window of opportunity for userspace to force a change of affinity for a VPE while the VPE has already been unmapped, but the corresponding doorbell interrupt still visible in /proc/irq/. Plug the race by checking the value of vmapp_count, which tracks whether the VPE is mapped ot not, and returning an error in this case. This involves making vmapp_count common to both GICv4.1 and its v4.0 ancestor. Fixes: 64edfaa9a234 ("irqchip/gic-v4.1: Implement the v4.1 flavour of VMAPP") Reported-by: Kunkun Jiang <jiangkunkun@huawei.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/c182ece6-2ba0-ce4f-3404-dba7a3ab6c52@huawei.com Link: https://lore.kernel.org/all/20241002204959.2051709-1-maz@kernel.org
2024-10-08selftests: make kselftest-clean remove libynl outputsGreg Thelen
Starting with 6.12 commit 85585b4bc8d8 ("selftests: add ncdevmem, netcat for devmem TCP") kselftest-all creates additional outputs that kselftest-clean does not cleanup: $ make defconfig $ make kselftest-all $ make kselftest-clean $ git clean -ndxf | grep tools/net Would remove tools/net/ynl/lib/__pycache__/ Would remove tools/net/ynl/lib/ynl.a Would remove tools/net/ynl/lib/ynl.d Would remove tools/net/ynl/lib/ynl.o Make kselftest-clean remove the newly added net/ynl outputs. Fixes: 85585b4bc8d8 ("selftests: add ncdevmem, netcat for devmem TCP") Signed-off-by: Greg Thelen <gthelen@google.com> Reviewed-by: Muhammad Usama Anjum <usama.anjum@collabora.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Link: https://patch.msgid.link/20241005215600.852260-1-gthelen@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-10-08Merge branch 'selftests-net-add-missing-gitignore-and-extra_clean-entries'Jakub Kicinski
Javier Carrasco says: ==================== selftests: net: add missing gitignore and EXTRA_CLEAN entries. This series is a cherry-pick on top of v6.12-rc1 from the one I sent for selftests with other patches that were not net-related: https://lore.kernel.org/all/20240925-selftests-gitignore-v3-0-9db896474170@gmail.com/ The patches have not been modified, and the Reviewed-by tags have been kept. v1: https://lore.kernel.org/20240930-net-selftests-gitignore-v1-0-65225a855946@gmail.com ==================== Link: https://patch.msgid.link/20241005-net-selftests-gitignore-v2-0-3a0b2876394a@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-10-08selftests: net: rds: add gitignore file for include.shJavier Carrasco
The generated include.sh should be ignored by git. Create a new gitignore and add the file to the list. Reviewed-by: Allison Henderson <allison.henderson@oracle.com> Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com> Link: https://patch.msgid.link/20241005-net-selftests-gitignore-v2-3-3a0b2876394a@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-10-08selftests: net: rds: add include.sh to EXTRA_CLEANJavier Carrasco
The include.sh file is generated when building the net/rds selftests, but there is no rule to delete it with the clean target. Add the file to EXTRA_CLEAN in order to remove it when required. Reviewed-by: Allison Henderson <allison.henderson@oracle.com> Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com> Link: https://patch.msgid.link/20241005-net-selftests-gitignore-v2-2-3a0b2876394a@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-10-08selftests: net: add msg_oob to gitignoreJavier Carrasco
This executable is missing from the corresponding gitignore file. Add msg_oob to the net gitignore list. Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com> Link: https://patch.msgid.link/20241005-net-selftests-gitignore-v2-1-3a0b2876394a@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-10-08x86/xen: mark boot CPU of PV guest in MSR_IA32_APICBASEJuergen Gross
Recent topology checks of the x86 boot code uncovered the need for PV guests to have the boot cpu marked in the APICBASE MSR. Fixes: 9d22c96316ac ("x86/topology: Handle bogus ACPI tables correctly") Reported-by: Niels Dettenbach <nd@syndicat.com> Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Juergen Gross <jgross@suse.com>
2024-10-08drm/radeon: always set GEM function pointerChristian König
Make sure to always set the GEM function pointer even for in kernel allocations. This fixes a NULL pointer deref caused by switching to GEM references. Signed-off-by: Christian König <christian.koenig@amd.com> Fixes: fd69ef05029f ("drm/radeon: use GEM references instead of TTMs") Acked-by: Alex Deucher <alexander.deucher@amd.com> Tested-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> (cherry picked from commit 01b64bc063d014641631867a7e0edd8ac55282d4)
2024-10-08x86/resctrl: Avoid overflow in MB settings in bw_validate()Martin Kletzander
The resctrl schemata file supports specifying memory bandwidth associated with the Memory Bandwidth Allocation (MBA) feature via a percentage (this is the default) or bandwidth in MiBps (when resctrl is mounted with the "mba_MBps" option). The allowed range for the bandwidth percentage is from /sys/fs/resctrl/info/MB/min_bandwidth to 100, using a granularity of /sys/fs/resctrl/info/MB/bandwidth_gran. The supported range for the MiBps bandwidth is 0 to U32_MAX. There are two issues with parsing of MiBps memory bandwidth: * The user provided MiBps is mistakenly rounded up to the granularity that is unique to percentage input. * The user provided MiBps is parsed using unsigned long (thus accepting values up to ULONG_MAX), and then assigned to u32 that could result in overflow. Do not round up the MiBps value and parse user provided bandwidth as the u32 it is intended to be. Use the appropriate kstrtou32() that can detect out of range values. Fixes: 8205a078ba78 ("x86/intel_rdt/mba_sc: Add schemata support") Fixes: 6ce1560d35f6 ("x86/resctrl: Switch over to the resctrl mbps_val list") Co-developed-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: Martin Kletzander <nert.pinx@gmail.com> Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de> Reviewed-by: Reinette Chatre <reinette.chatre@intel.com> Reviewed-by: Tony Luck <tony.luck@intel.com>
2024-10-08gpio: aspeed: Use devm_clk api to manage clock sourceBilly Tsai
Replace of_clk_get with devm_clk_get_enabled to manage the clock source. Fixes: 5ae4cb94b313 ("gpio: aspeed: Add debounce support") Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au> Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com> Link: https://lore.kernel.org/r/20241008081450.1490955-3-billy_tsai@aspeedtech.com Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
2024-10-08gpio: aspeed: Add the flush write to ensure the write complete.Billy Tsai
Performing a dummy read ensures that the register write operation is fully completed, mitigating any potential bus delays that could otherwise impact the frequency of bitbang usage. E.g., if the JTAG application uses GPIO to control the JTAG pins (TCK, TMS, TDI, TDO, and TRST), and the application sets the TCK clock to 1 MHz, the GPIO's high/low transitions will rely on a delay function to ensure the clock frequency does not exceed 1 MHz. However, this can lead to rapid toggling of the GPIO because the write operation is POSTed and does not wait for a bus acknowledgment. Fixes: 361b79119a4b ("gpio: Add Aspeed driver") Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au> Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com> Link: https://lore.kernel.org/r/20241008081450.1490955-2-billy_tsai@aspeedtech.com Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
2024-10-08nouveau/dmem: Fix vulnerability in migrate_to_ram upon copy errorYonatan Maman
The `nouveau_dmem_copy_one` function ensures that the copy push command is sent to the device firmware but does not track whether it was executed successfully. In the case of a copy error (e.g., firmware or hardware failure), the copy push command will be sent via the firmware channel, and `nouveau_dmem_copy_one` will likely report success, leading to the `migrate_to_ram` function returning a dirty HIGH_USER page to the user. This can result in a security vulnerability, as a HIGH_USER page that may contain sensitive or corrupted data could be returned to the user. To prevent this vulnerability, we allocate a zero page. Thus, in case of an error, a non-dirty (zero) page will be returned to the user. Fixes: 5be73b690875 ("drm/nouveau/dmem: device memory helpers for SVM") Signed-off-by: Yonatan Maman <Ymaman@Nvidia.com> Co-developed-by: Gal Shalom <GalShalom@Nvidia.com> Signed-off-by: Gal Shalom <GalShalom@Nvidia.com> Reviewed-by: Ben Skeggs <bskeggs@nvidia.com> Cc: stable@vger.kernel.org Signed-off-by: Danilo Krummrich <dakr@kernel.org> Link: https://patchwork.freedesktop.org/patch/msgid/20241008115943.990286-3-ymaman@nvidia.com
2024-10-08nouveau/dmem: Fix privileged error in copy engine channelYonatan Maman
When `nouveau_dmem_copy_one` is called, the following error occurs: [272146.675156] nouveau 0000:06:00.0: fifo: PBDMA9: 00000004 [HCE_PRIV] ch 1 00000300 00003386 This indicates that a copy push command triggered a Host Copy Engine Privileged error on channel 1 (Copy Engine channel). To address this issue, modify the Copy Engine channel to allow privileged push commands Fixes: 6de125383a5c ("drm/nouveau/fifo: expose runlist topology info on all chipsets") Signed-off-by: Yonatan Maman <Ymaman@Nvidia.com> Co-developed-by: Gal Shalom <GalShalom@Nvidia.com> Signed-off-by: Gal Shalom <GalShalom@Nvidia.com> Reviewed-by: Ben Skeggs <bskeggs@nvidia.com> Signed-off-by: Danilo Krummrich <dakr@kernel.org> Link: https://patchwork.freedesktop.org/patch/msgid/20241008115943.990286-2-ymaman@nvidia.com
2024-10-08RDMA/core: Fix ENODEV error for iWARP test over vlanAnumula Murali Mohan Reddy
If traffic is over vlan, cma_validate_port() fails to match vlan net_device ifindex with bound_if_index and results in ENODEV error. It is because rdma_copy_src_l2_addr() always assigns bound_if_index with real net_device ifindex. This patch fixes the issue by assigning bound_if_index with vlan net_device index if traffic is over vlan. Fixes: f8ef1be816bf ("RDMA/cma: Avoid GID lookups on iWARP devices") Signed-off-by: Anumula Murali Mohan Reddy <anumula@chelsio.com> Signed-off-by: Potnuri Bharat Teja <bharat@chelsio.com> Link: https://patch.msgid.link/20241008114334.146702-1-anumula@chelsio.com Signed-off-by: Leon Romanovsky <leon@kernel.org>
2024-10-08KVM: arm64: Expose S1PIE to guestsMark Brown
Prior to commit 70ed7238297f ("KVM: arm64: Sanitise ID_AA64MMFR3_EL1") we just exposed the santised view of ID_AA64MMFR3_EL1 to guests, meaning that they saw both TCRX and S1PIE if present on the host machine. That commit added VMM control over the contents of the register and exposed S1POE but removed S1PIE, meaning that the extension is no longer visible to guests. Reenable support for S1PIE with VMM control. Fixes: 70ed7238297f ("KVM: arm64: Sanitise ID_AA64MMFR3_EL1") Signed-off-by: Mark Brown <broonie@kernel.org> Reviewed-by: Joey Gouly <joey.gouly@arm.com> Link: https://lore.kernel.org/r/20241005-kvm-arm64-fix-s1pie-v1-1-5901f02de749@kernel.org Signed-off-by: Marc Zyngier <maz@kernel.org>
2024-10-08KVM: arm64: nv: Clarify safety of allowing TLBI unmaps to rescheduleOliver Upton
There's been a decent amount of attention around unmaps of nested MMUs, and TLBI handling is no exception to this. Add a comment clarifying why it is safe to reschedule during a TLBI unmap, even without a reference on the MMU in progress. Signed-off-by: Oliver Upton <oliver.upton@linux.dev> Link: https://lore.kernel.org/r/20241007233028.2236133-5-oliver.upton@linux.dev Signed-off-by: Marc Zyngier <maz@kernel.org>
2024-10-08KVM: arm64: nv: Punt stage-2 recycling to a vCPU requestOliver Upton
Currently, when a nested MMU is repurposed for some other MMU context, KVM unmaps everything during vcpu_load() while holding the MMU lock for write. This is quite a performance bottleneck for large nested VMs, as all vCPU scheduling will spin until the unmap completes. Start punting the MMU cleanup to a vCPU request, where it is then possible to periodically release the MMU lock and CPU in the presence of contention. Ensure that no vCPU winds up using a stale MMU by tracking the pending unmap on the S2 MMU itself and requesting an unmap on every vCPU that finds it. Signed-off-by: Oliver Upton <oliver.upton@linux.dev> Link: https://lore.kernel.org/r/20241007233028.2236133-4-oliver.upton@linux.dev Signed-off-by: Marc Zyngier <maz@kernel.org>
2024-10-08KVM: arm64: nv: Do not block when unmapping stage-2 if disallowedOliver Upton
Right now the nested code allows unmap operations on a shadow stage-2 to block unconditionally. This is wrong in a couple places, such as a non-blocking MMU notifier or on the back of a sched_in() notifier as part of shadow MMU recycling. Carry through whether or not blocking is allowed to kvm_pgtable_stage2_unmap(). This 'fixes' an issue where stage-2 MMU reclaim would precipitate a stack overflow from a pile of kvm_sched_in() callbacks, all trying to recycle a stage-2 MMU. Signed-off-by: Oliver Upton <oliver.upton@linux.dev> Link: https://lore.kernel.org/r/20241007233028.2236133-3-oliver.upton@linux.dev Signed-off-by: Marc Zyngier <maz@kernel.org>
2024-10-08KVM: arm64: nv: Keep reference on stage-2 MMU when scheduled outOliver Upton
If a vCPU is scheduling out and not in WFI emulation, it is highly likely it will get scheduled again soon and reuse the MMU it had before. Dropping the MMU at vcpu_put() can have some unfortunate consequences, as the MMU could get reclaimed and used in a different context, forcing another 'cold start' on an otherwise active MMU. Avoid that altogether by keeping a reference on the MMU if the vCPU is scheduling out, ensuring that another vCPU cannot reclaim it while the current vCPU is away. Since there are more MMUs than vCPUs, this does not affect the guarantee that an unused MMU is available at any time. Furthermore, this makes the vcpu->arch.hw_mmu ~stable in preemptible code, at least for where it matters in the stage-2 abort path. Yes, the MMU can change across WFI emulation, but there isn't even a use case where this would matter. Signed-off-by: Oliver Upton <oliver.upton@linux.dev> Link: https://lore.kernel.org/r/20241007233028.2236133-2-oliver.upton@linux.dev Signed-off-by: Marc Zyngier <maz@kernel.org>
2024-10-08KVM: arm64: Unregister redistributor for failed vCPU creationOliver Upton
Alex reports that syzkaller has managed to trigger a use-after-free when tearing down a VM: BUG: KASAN: slab-use-after-free in kvm_put_kvm+0x300/0xe68 virt/kvm/kvm_main.c:5769 Read of size 8 at addr ffffff801c6890d0 by task syz.3.2219/10758 CPU: 3 UID: 0 PID: 10758 Comm: syz.3.2219 Not tainted 6.11.0-rc6-dirty #64 Hardware name: linux,dummy-virt (DT) Call trace: dump_backtrace+0x17c/0x1a8 arch/arm64/kernel/stacktrace.c:317 show_stack+0x2c/0x3c arch/arm64/kernel/stacktrace.c:324 __dump_stack lib/dump_stack.c:93 [inline] dump_stack_lvl+0x94/0xc0 lib/dump_stack.c:119 print_report+0x144/0x7a4 mm/kasan/report.c:377 kasan_report+0xcc/0x128 mm/kasan/report.c:601 __asan_report_load8_noabort+0x20/0x2c mm/kasan/report_generic.c:381 kvm_put_kvm+0x300/0xe68 virt/kvm/kvm_main.c:5769 kvm_vm_release+0x4c/0x60 virt/kvm/kvm_main.c:1409 __fput+0x198/0x71c fs/file_table.c:422 ____fput+0x20/0x30 fs/file_table.c:450 task_work_run+0x1cc/0x23c kernel/task_work.c:228 do_notify_resume+0x144/0x1a0 include/linux/resume_user_mode.h:50 el0_svc+0x64/0x68 arch/arm64/kernel/entry-common.c:169 el0t_64_sync_handler+0x90/0xfc arch/arm64/kernel/entry-common.c:730 el0t_64_sync+0x190/0x194 arch/arm64/kernel/entry.S:598 Upon closer inspection, it appears that we do not properly tear down the MMIO registration for a vCPU that fails creation late in the game, e.g. a vCPU w/ the same ID already exists in the VM. It is important to consider the context of commit that introduced this bug by moving the unregistration out of __kvm_vgic_vcpu_destroy(). That change correctly sought to avoid an srcu v. config_lock inversion by breaking up the vCPU teardown into two parts, one guarded by the config_lock. Fix the use-after-free while avoiding lock inversion by adding a special-cased unregistration to __kvm_vgic_vcpu_destroy(). This is safe because failed vCPUs are torn down outside of the config_lock. Cc: stable@vger.kernel.org Fixes: f616506754d3 ("KVM: arm64: vgic: Don't hold config_lock while unregistering redistributors") Reported-by: Alexander Potapenko <glider@google.com> Signed-off-by: Oliver Upton <oliver.upton@linux.dev> Link: https://lore.kernel.org/r/20241007223909.2157336-1-oliver.upton@linux.dev Signed-off-by: Marc Zyngier <maz@kernel.org>
2024-10-08Merge branch kvm-arm64/idregs-6.12 into kvmarm/fixesMarc Zyngier
* kvm-arm64/idregs-6.12: : . : Make some fields of ID_AA64DFR0_EL1 and ID_AA64PFR1_EL1 : writable from userspace, so that a VMM can influence the : set of guest-visible features. : : - for ID_AA64DFR0_EL1: DoubleLock, WRPs, PMUVer and DebugVer : are writable (courtesy of Shameer Kolothum) : : - for ID_AA64PFR1_EL1: BT, SSBS, CVS2_frac are writable : (courtesy of Shaoqin Huang) : . KVM: selftests: aarch64: Add writable test for ID_AA64PFR1_EL1 KVM: arm64: Allow userspace to change ID_AA64PFR1_EL1 KVM: arm64: Use kvm_has_feat() to check if FEAT_SSBS is advertised to the guest KVM: arm64: Disable fields that KVM doesn't know how to handle in ID_AA64PFR1_EL1 KVM: arm64: Make the exposed feature bits in AA64DFR0_EL1 writable from userspace Signed-off-by: Marc Zyngier <maz@kernel.org>
2024-10-08Merge branch 'net-dsa-b53-assorted-jumbo-frame-fixes'Paolo Abeni
Jonas Gorski says: ==================== net: dsa: b53: assorted jumbo frame fixes While investigating the capabilities of BCM63XX's integrated switch and its DMA engine, I noticed a few issues in b53's jumbo frame code. Mostly a confusion of MTU vs frame length, but also a few missing cases for 100M switches. Tested on BCM63XX and BCM53115 with intel 1G and realtek 1G NICs, which support MTUs of 9000 or slightly above, but significantly less than the 9716/9720 supported by BCM53115, so I couldn't verify the actual maximum frame length. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> --- ==================== Link: https://patch.msgid.link/20241004-b53_jumbo_fixes-v1-0-ce1e54aa7b3c@gmail.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2024-10-08net: dsa: b53: fix jumbo frames on 10/100 portsJonas Gorski
All modern chips support and need the 10_100 bit set for supporting jumbo frames on 10/100 ports, so instead of enabling it only for 583XX enable it for everything except bcm63xx, where the bit is writeable, but does nothing. Tested on BCM53115, where jumbo frames were dropped at 10/100 speeds without the bit set. Fixes: 6ae5834b983a ("net: dsa: b53: add MTU configuration support") Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
generated by cgit (git 2.34.1) at 2025-09-14 02:31:25 +0000