| Age | Commit message (Collapse) | Author |
|---|
|
After commit 9f76779f2418 ("MIPS: implement architecture-specific
'pci_remap_iospace()'"), there exists the following warning on the
Loongson64 platform:
loongson-pci 1a000000.pci: IO 0x0018020000..0x001803ffff -> 0x0000020000
loongson-pci 1a000000.pci: MEM 0x0040000000..0x007fffffff -> 0x0040000000
------------[ cut here ]------------
WARNING: CPU: 2 PID: 1 at arch/mips/pci/pci-generic.c:55 pci_remap_iospace+0x84/0x90
resource start address is not zero
...
Call Trace:
[<ffffffff8020dc78>] show_stack+0x40/0x120
[<ffffffff80cf4a0c>] dump_stack_lvl+0x58/0x74
[<ffffffff8023a0b0>] __warn+0xe0/0x110
[<ffffffff80cee02c>] warn_slowpath_fmt+0xa4/0xd0
[<ffffffff80cecf24>] pci_remap_iospace+0x84/0x90
[<ffffffff807f9864>] devm_pci_remap_iospace+0x5c/0xb8
[<ffffffff808121b0>] devm_of_pci_bridge_init+0x178/0x1f8
[<ffffffff807f4000>] devm_pci_alloc_host_bridge+0x78/0x98
[<ffffffff80819454>] loongson_pci_probe+0x34/0x160
[<ffffffff809203cc>] platform_probe+0x6c/0xe0
[<ffffffff8091d5d4>] really_probe+0xbc/0x340
[<ffffffff8091d8f0>] __driver_probe_device+0x98/0x110
[<ffffffff8091d9b8>] driver_probe_device+0x50/0x118
[<ffffffff8091dea0>] __driver_attach+0x80/0x118
[<ffffffff8091b280>] bus_for_each_dev+0x80/0xc8
[<ffffffff8091c6d8>] bus_add_driver+0x130/0x210
[<ffffffff8091ead4>] driver_register+0x8c/0x150
[<ffffffff80200a8c>] do_one_initcall+0x54/0x288
[<ffffffff811a5320>] kernel_init_freeable+0x27c/0x2e4
[<ffffffff80cfc380>] kernel_init+0x2c/0x134
[<ffffffff80205a2c>] ret_from_kernel_thread+0x14/0x1c
---[ end trace e4a0efe10aa5cce6 ]---
loongson-pci 1a000000.pci: error -19: failed to map resource [io 0x20000-0x3ffff]
We can see that the resource start address is 0x0000020000, because
the ISA Bridge used the zero address which is defined in the dts file
arch/mips/boot/dts/loongson/ls7a-pch.dtsi:
ISA Bridge: /bus@10000000/isa@18000000
IO 0x0000000018000000..0x000000001801ffff -> 0x0000000000000000
Based on the above analysis, the architecture-specific pci_remap_iospace()
is not suitable for Loongson64, we should only define pci_remap_iospace()
for Ralink on MIPS based on the commit background.
Fixes: 9f76779f2418 ("MIPS: implement architecture-specific 'pci_remap_iospace()'")
Suggested-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Tested-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Acked-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
The driver currently assumes that the notify callback is only received
when the device is done with all the queued buffers.
However, this is not true, since the notify callback could be called
without any of the queued buffers being completed (for example, with
virtio-pci and shared interrupts) or with only some of the buffers being
completed (since the driver makes them available to the device in
multiple separate virtqueue_add_sgs() calls).
This can lead to incorrect data on the I2C bus or memory corruption in
the guest if the device operates on buffers which are have been freed by
the driver. (The WARN_ON in the driver is also triggered.)
BUG kmalloc-128 (Tainted: G W ): Poison overwritten
First byte 0x0 instead of 0x6b
Allocated in i2cdev_ioctl_rdwr+0x9d/0x1de age=243 cpu=0 pid=28
memdup_user+0x2e/0xbd
i2cdev_ioctl_rdwr+0x9d/0x1de
i2cdev_ioctl+0x247/0x2ed
vfs_ioctl+0x21/0x30
sys_ioctl+0xb18/0xb41
Freed in i2cdev_ioctl_rdwr+0x1bb/0x1de age=68 cpu=0 pid=28
kfree+0x1bd/0x1cc
i2cdev_ioctl_rdwr+0x1bb/0x1de
i2cdev_ioctl+0x247/0x2ed
vfs_ioctl+0x21/0x30
sys_ioctl+0xb18/0xb41
Fix this by calling virtio_get_buf() from the notify handler like other
virtio drivers and by actually waiting for all the buffers to be
completed.
Fixes: 3cfc88380413d20f ("i2c: virtio: add a virtio i2c frontend driver")
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
When scan request on channel 1, it also receive beacon from other
channels, and the beacon also indicate to mac80211 and wpa_supplicant,
and then the bss info appears in radio measurement report of radio
measurement sent from wpa_supplicant, thus lead RRM case fail.
This is to drop the beacon and probe response which is not the same
channel of scanning.
Tested-on: QCA6174 hw3.2 SDIO WLAN.RMH.4.4.1-00049
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211208061752.16564-1-quic_wgong@quicinc.com
|
|
Currently there is no validation on the spectral/CFR report
over the db ring buffers from the hardware. Improper/incomplete
DMA by the target can result in invalid data received by host.
Due to this we may populate incorrect data to user space.
This buffer validation support fix this issues by filling some
magic value in the buffer during buffer replenish and check for
the magic value in the buffer received by the target. If host
detect magic value in the received buffer it will drop the buffer.
Tested-on: IPQ8074 WLAN.HK.2.4.0.1-01467-QCAHKSWPL_SILICONZ-1
Signed-off-by: Venkateswara Naralasetty <quic_vnaralas@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1637312901-10279-2-git-send-email-quic_vnaralas@quicinc.com
|
|
In full monitor mode, monitor destination ring is read before monitor
status ring. mon_dst_ring has ppdu id, reap till the end of PPDU. Add
all the MPDUs to list. Start processing the status ring, if PPDU id in
status ring is lagging behind, reap the status ring, once the PPDU ID
matches, deliver the MSDU to upper layer. If status PPDU id leading,
reap the mon_dst_ring.
The advantage with full monitor mode is hardware has status buffers
available for all the MPDUs in mon_dst_ring, which makes it possible
to deliver more frames to be seen on sniffer.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1638881695-22155-4-git-send-email-akolli@codeaurora.org
|
|
In full monitor mode, monitor destination ring is read in
software monitor ring descriptor format instead of
reo_entrance_ring format. Add new sw_mon_ring descriptor.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1638881695-22155-3-git-send-email-akolli@codeaurora.org
|
|
A new hw_param full_monitor_mode is added to enable full
monitor support for QCN9074.
HTT_H2T_MSG_TYPE_RX_FULL_MONITOR_MODE cmd is sent to FW
to enable the full monitor mode.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1638881695-22155-2-git-send-email-akolli@codeaurora.org
|
|
The CAN clock frequency is used when calculating the CAN bittiming
parameters. When wrong clock frequency is used, the device may end up
with wrong bittiming parameters, depending on user requested bittiming
parameters.
To avoid this, get the CAN clock frequency from the device. Various
existing Kvaser Leaf products use different CAN clocks.
Fixes: 080f40a6fa28 ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Link: https://lore.kernel.org/all/20211208152122.250852-2-extja@kvaser.com
Cc: stable@vger.kernel.org
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
stats->{rx,tx}_errors counter
Check the direction bit in the error frame packet (EPACK) to determine
which net_device_stats {rx,tx}_errors counter to increase.
Fixes: 26ad340e582d ("can: kvaser_pciefd: Add driver for Kvaser PCIEcan devices")
Link: https://lore.kernel.org/all/20211208152122.250852-1-extja@kvaser.com
Cc: stable@vger.kernel.org
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
In builds with -Warray-bounds, casts from smaller objects to larger
objects will produce warnings. These can be overly conservative, but since
-Warray-bounds has been finding legitimate bugs, it is desirable to turn
it on globally. Instead of casting a u32 to a larger object, redefine
the u32 portion of the header to a separate struct that can be used for
both u32 operations and the distinct header fields. Silences this warning:
drivers/net/wireless/ath/ath6kl/htc_mbox.c: In function 'htc_wait_for_ctrl_msg':
drivers/net/wireless/ath/ath6kl/htc_mbox.c:2275:20: error: array subscript 'struct htc_frame_hdr[0]' is partly outside array bounds of 'u32[1]' {aka 'unsigned int[1]'} [-Werror=array-bounds]
2275 | if (htc_hdr->eid != ENDPOINT_0)
| ^~
drivers/net/wireless/ath/ath6kl/htc_mbox.c:2264:13: note: while referencing 'look_ahead'
2264 | u32 look_ahead;
| ^~~~~~~~~~
This change results in no executable instruction differences.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211207063538.2767954-1-keescook@chromium.org
|
|
Currently mac80211 will send 3 scan request for each scan of WCN6855,
they are 2.4 GHz/5 GHz/6 GHz band scan. Firmware of WCN6855 will
cache the RNR IE(Reduced Neighbor Report element) which exist in the
beacon of 2.4 GHz/5 GHz of the AP which is co-located with 6 GHz,
and then use the cache to scan in 6 GHz band scan if the 6 GHz scan
is in the same scan with the 2.4 GHz/5 GHz band, this will helpful to
search more AP of 6 GHz. Also it will decrease the time cost of scan
because firmware will use dual-band scan for the 2.4 GHz/5 GHz, it
means the 2.4 GHz and 5 GHz scans are doing simultaneously.
Set the flag IEEE80211_HW_SINGLE_SCAN_ON_ALL_BANDS for WCN6855 since
it supports 2.4 GHz/5 GHz/6 GHz and it is single pdev which means
all the 2.4 GHz/5 GHz/6 GHz exist in the same wiphy/ieee80211_hw.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211129101309.2931-1-quic_wgong@quicinc.com
|
|
If cfg80211 is providing extraie's for a scanning process then ath11k will
copy that over to the firmware. The extraie.len is a 32 bit value in struct
element_info and describes the amount of bytes for the vendor information
elements.
The WMI_TLV packet is having a special WMI_TAG_ARRAY_BYTE section. This
section can have a (payload) length up to 65535 bytes because the
WMI_TLV_LEN can store up to 16 bits. The code was missing such a check and
could have created a scan request which cannot be parsed correctly by the
firmware.
But the bigger problem was the allocation of the buffer. It has to align
the TLV sections by 4 bytes. But the code was using an u8 to store the
newly calculated length of this section (with alignment). And the new
calculated length was then used to allocate the skbuff. But the actual code
to copy in the data is using the extraie.len and not the calculated
"aligned" length.
The length of extraie with IEEE80211_HW_SINGLE_SCAN_ON_ALL_BANDS enabled
was 264 bytes during tests with a QCA Milan card. But it only allocated 8
bytes (264 bytes % 256) for it. As consequence, the code to memcpy the
extraie into the skb was then just overwriting data after skb->end. Things
like shinfo were therefore corrupted. This could usually be seen by a crash
in skb_zcopy_clear which tried to call a ubuf_info callback (using a bogus
address).
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-02892.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Cc: stable@vger.kernel.org
Fixes: d5c65159f289 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211207142913.1734635-1-sven@narfation.org
|
|
The pointer t is being initialized with a value that is never read. The
pointer is re-assigned a value a littler later on, hence the initialization
is redundant and can be removed.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20211207224718.59593-1-colin.i.king@gmail.com
|
|
The following warning is triggered when I used clang compiler
to build the selftest.
/.../prog_tests/btf_dedup_split.c:368:6: warning: variable 'btf2' is used uninitialized whenever 'if' condition is true [-Wsometimes-uninitialized]
if (!ASSERT_OK(err, "btf_dedup"))
^~~~~~~~~~~~~~~~~~~~~~~~~~~~
/.../prog_tests/btf_dedup_split.c:424:12: note: uninitialized use occurs here
btf__free(btf2);
^~~~
/.../prog_tests/btf_dedup_split.c:368:2: note: remove the 'if' if its condition is always false
if (!ASSERT_OK(err, "btf_dedup"))
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
/.../prog_tests/btf_dedup_split.c:343:25: note: initialize the variable 'btf2' to silence this warning
struct btf *btf1, *btf2;
^
= NULL
Initialize local variable btf2 = NULL and the warning is gone.
Fixes: 9a49afe6f5a5 ("selftests/bpf: Add btf_dedup case with duplicated structs within CU")
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20211209050403.1770836-1-yhs@fb.com
|
|
[why/how]
The function can be called on boot or after suspend when
links are not initialized, to prevent it guard it with
NULL pointer check
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Pavle Kotarac <Pavle.Kotarac@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
The HW interrupt gets disabled after S3/S4/reset so we don't receive
notifications for HPD or AUX from DMUB - leading to timeout and
black screen with (or without) DPIA links connected.
[How]
Re-enable the interrupt after S3/S4/reset like we do for the other
DC interrupts.
Guard both instances of the outbox interrupt enable or we'll hang
during restore on ASIC that don't support it.
Fixes: 6eff272dbee7ad ("drm/amd/display: Fix DPIA outbox timeout after GPU reset")
Reviewed-by: Jude Shih <Jude.Shih@amd.com>
Acked-by: Pavle Kotarac <Pavle.Kotarac@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Use 2-factor multiplication argument form devm_kcalloc() instead
of devm_kzalloc().
Link: https://github.com/KSPP/linux/issues/162
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20211208040311.GA169838@embeddedor
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use 2-factor multiplication argument form devm_kcalloc() instead
of devm_kzalloc().
Link: https://github.com/KSPP/linux/issues/162
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20211208003527.GA75483@embeddedor
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Antoine Tenart says:
====================
net: track the queue count at unregistration
Those two patches allow to track the Rx and Tx queue count at
unregistration and help in detecting illegal addition of Tx queues after
unregister (a warning is added).
This follows discussions on the following thread,
https://lore.kernel.org/all/20211122162007.303623-1-atenart@kernel.org/T/
A patch fixing one issue linked to this was merged ealier,
https://lore.kernel.org/all/20211203101318.435618-1-atenart@kernel.org/T/
====================
Link: https://lore.kernel.org/r/20211207145725.352657-1-atenart@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
unregistration
Calling netdev_queue_update_kobjects is allowed during device
unregistration since commit 5c56580b74e5 ("net: Adjust TX queue kobjects
if number of queues changes during unregister"). But this is solely to
allow queue unregistrations. Any path attempting to add new queues after
a device started its unregistration should be fixed.
This patch adds a warning to detect such illegal use.
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When updating Rx and Tx queue kobjects, the queue count should always be
updated to match the queue kobjects count. This was not done in the net
device unregistration path, fix it. Tracking all queue count updates
will allow in a following up patch to detect illegal updates.
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The registration of XDP queue information is incorrect because the
RX queue id we use is invalid. When port->id == 0 it appears to works
as expected yet it's no longer the case when port->id != 0.
The problem arised while using a recent kernel version on the
MACCHIATOBin. This board has several ports:
* eth0 and eth1 are 10Gbps interfaces ; both ports has port->id == 0;
* eth2 is a 1Gbps interface with port->id != 0.
Code from xdp-tutorial (more specifically advanced03-AF_XDP) was used
to test packet capture and injection on all these interfaces. The XDP
kernel was simplified to:
SEC("xdp_sock")
int xdp_sock_prog(struct xdp_md *ctx)
{
int index = ctx->rx_queue_index;
/* A set entry here means that the correspnding queue_id
* has an active AF_XDP socket bound to it. */
if (bpf_map_lookup_elem(&xsks_map, &index))
return bpf_redirect_map(&xsks_map, index, 0);
return XDP_PASS;
}
Starting the program using:
./af_xdp_user -d DEV
Gives the following result:
* eth0 : ok
* eth1 : ok
* eth2 : no capture, no injection
Investigating the issue shows that XDP rx queues for eth2 are wrong:
XDP expects their id to be in the range [0..3] but we found them to be
in the range [32..35].
Trying to force rx queue ids using:
./af_xdp_user -d eth2 -Q 32
fails as expected (we shall not have more than 4 queues).
When we register the XDP rx queue information (using
xdp_rxq_info_reg() in function mvpp2_rxq_init()) we tell it to use
rxq->id as the queue id. This value is computed as:
rxq->id = port->id * max_rxq_count + queue_id
where max_rxq_count depends on the device version. In the MACCHIATOBin
case, this value is 32, meaning that rx queues on eth2 are numbered
from 32 to 35 - there are four of them.
Clearly, this is not the per-port queue id that XDP is expecting:
it wants a value in the range [0..3]. It shall directly use queue_id
which is stored in rxq->logic_rxq -- so let's use that value instead.
rxq->id is left untouched ; its value is indeed valid but it should
not be used in this context.
This is consistent with the remaining part of the code in
mvpp2_rxq_init().
With this change, packet capture is working as expected on all the
MACCHIATOBin ports.
Fixes: b27db2274ba8 ("mvpp2: use page_pool allocator")
Signed-off-by: Louis Amas <louis.amas@eho.link>
Signed-off-by: Emmanuel Deloget <emmanuel.deloget@eho.link>
Reviewed-by: Marcin Wojtas <mw@semihalf.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Link: https://lore.kernel.org/r/20211207143423.916334-1-louis.amas@eho.link
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The ASMedia 1092 has a configuration mode which will present a
dummy device; sadly the implementation falsely claims to provide
a device with 100M which doesn't actually exist.
So disable this device to avoid errors during boot.
Cc: stable@vger.kernel.org
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
Sergey Ryazanov says:
====================
WWAN debugfs tweaks
This is a follow-up series to just applied IOSM (and WWAN) debugfs
interface support [1]. The series has two main goals:
1. move the driver-specific debugfs knobs to a subdirectory;
2. make the debugfs interface optional for both IOSM and for the WWAN
core.
As for the first part, I must say that it was my mistake. I suggested to
place debugfs entries under a common per WWAN device directory. But I
missed the driver subdirectory in the example, so it become:
/sys/kernel/debugfs/wwan/wwan0/trace
Since the traces collection is a driver-specific feature, it is better
to keep it under the driver-specific subdirectory:
/sys/kernel/debugfs/wwan/wwan0/iosm/trace
It is desirable to be able to entirely disable the debugfs interface. It
can be disabled for several reasons, including security and consumed
storage space. See detailed rationale with usage example in the 4th
patch.
The changes themselves are relatively simple, but require a code
rearrangement. So to make changes clear, I chose to split them into
preparatory and main changes and properly describe each of them.
IOSM part is compile-tested only since I do not have IOSM supported
device, so it needs Ack from the driver developers.
I would like to thank Johannes Berg and Leon Romanovsky. Their
suggestions and comments helped a lot to rework the initial
over-engineered solution to something less confusing and much more
simple. Thanks!
1. https://lore.kernel.org/netdev/20211120162155.1216081-1-m.chetan.kumar@linux.intel.com
2. https://patchwork.kernel.org/project/netdevbpf/patch/20211204174033.950528-1-arnd@kernel.org/
====================
Link: https://lore.kernel.org/r/20211207092140.19142-1-ryazanov.s.a@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Debugfs interface is optional for the regular modem use. Some distros
and users will want to disable this feature for security or kernel
size reasons. So add a configuration option that allows to completely
disable the debugfs interface of the WWAN devices.
A primary considered use case for this option was embedded firmwares.
For example, in OpenWrt, you can not completely disable debugfs, as a
lot of wireless stuff can only be configured and monitored with the
debugfs knobs. At the same time, reducing the size of a kernel and
modules is an essential task in the world of embedded software.
Disabling the WWAN and IOSM debugfs interfaces allows us to save 50K
(x86-64 build) of space for module storage. Not much, but already
considerable when you only have 16MB of storage.
So it is hard to just disable whole debugfs. Users need some fine
grained set of options to control which debugfs interface is important
and should be available and which is not.
The new configuration symbol is enabled by default and is hidden under
the EXPERT option. So a regular user would not be bothered by another
one configuration question. While an embedded distro maintainer will be
able to a little more reduce the final image size.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Acked-by: M Chetan Kumar <m.chetan.kumar@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The modem traces collection is a device (and so driver) specific option.
Therefore, move the related debugfs files into a driver-specific
subdirectory under the common per WWAN device directory.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Acked-by: M Chetan Kumar <m.chetan.kumar@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Collecting modem firmware traces is optional for the regular modem use.
There are not many reasons for aborting device initialization due to an
inability to initialize the trace port and (or) its debugfs interface.
So, demote the initialization failure erro message into a warning and do
not break the initialization sequence in this case. Rework packet
processing and deinitialization so that they do not crash in case of
uninitialized trace port.
This change is mainly a preparation for an upcoming configuration option
introduction that will help disable driver debugfs functionality.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Acked-by: M Chetan Kumar <m.chetan.kumar@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move the channel related structures initialization from
ipc_imem_channel_init() to ipc_trace_init() and call it directly. On the
one hand, this makes the trace port initialization symmetric to the
deitialization, that is, it removes the additional wrapper.
On the other hand, this change consolidates the trace port related code
into a single source file, what facilitates an upcoming disabling of
this functionality by a user choise.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Acked-by: M Chetan Kumar <m.chetan.kumar@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
'Commit 39f9895a00f4 ("vmxnet3: add support for 32 Tx/Rx queues")'
added support for 32Tx/Rx queues. Within that patch, value of
VMXNET3_LINUX_MIN_MSIX_VECT was updated.
However, there is a case (numvcpus = 2) which actually requires 3
intrs which matches VMXNET3_LINUX_MIN_MSIX_VECT which then is
treated as failure by stack to allocate more vectors. This patch
fixes this issue.
Fixes: 39f9895a00f4 ("vmxnet3: add support for 32 Tx/Rx queues")
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Acked-by: Guolin Yang <gyang@vmware.com>
Link: https://lore.kernel.org/r/20211207081737.14000-1-doshir@vmware.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit 2c611ad97a82 ("net, neigh: Extend neigh->flags to 32 bit
to allow for extensions") enables a new KMSAM warning [1]
I think the bug is actually older, because the following intruction
only occurred if ndm->ndm_flags had NTF_PROXY set.
pn->flags = ndm->ndm_flags;
Let's clear all pneigh_entry fields at alloc time.
[1]
BUG: KMSAN: uninit-value in pneigh_fill_info+0x986/0xb30 net/core/neighbour.c:2593
pneigh_fill_info+0x986/0xb30 net/core/neighbour.c:2593
pneigh_dump_table net/core/neighbour.c:2715 [inline]
neigh_dump_info+0x1e3f/0x2c60 net/core/neighbour.c:2832
netlink_dump+0xaca/0x16a0 net/netlink/af_netlink.c:2265
__netlink_dump_start+0xd1c/0xee0 net/netlink/af_netlink.c:2370
netlink_dump_start include/linux/netlink.h:254 [inline]
rtnetlink_rcv_msg+0x181b/0x18c0 net/core/rtnetlink.c:5534
netlink_rcv_skb+0x447/0x800 net/netlink/af_netlink.c:2491
rtnetlink_rcv+0x50/0x60 net/core/rtnetlink.c:5589
netlink_unicast_kernel net/netlink/af_netlink.c:1319 [inline]
netlink_unicast+0x1095/0x1360 net/netlink/af_netlink.c:1345
netlink_sendmsg+0x16f3/0x1870 net/netlink/af_netlink.c:1916
sock_sendmsg_nosec net/socket.c:704 [inline]
sock_sendmsg net/socket.c:724 [inline]
sock_write_iter+0x594/0x690 net/socket.c:1057
call_write_iter include/linux/fs.h:2162 [inline]
new_sync_write fs/read_write.c:503 [inline]
vfs_write+0x1318/0x2030 fs/read_write.c:590
ksys_write+0x28c/0x520 fs/read_write.c:643
__do_sys_write fs/read_write.c:655 [inline]
__se_sys_write fs/read_write.c:652 [inline]
__x64_sys_write+0xdb/0x120 fs/read_write.c:652
do_syscall_x64 arch/x86/entry/common.c:51 [inline]
do_syscall_64+0x54/0xd0 arch/x86/entry/common.c:82
entry_SYSCALL_64_after_hwframe+0x44/0xae
Uninit was created at:
slab_post_alloc_hook mm/slab.h:524 [inline]
slab_alloc_node mm/slub.c:3251 [inline]
slab_alloc mm/slub.c:3259 [inline]
__kmalloc+0xc3c/0x12d0 mm/slub.c:4437
kmalloc include/linux/slab.h:595 [inline]
pneigh_lookup+0x60f/0xd70 net/core/neighbour.c:766
arp_req_set_public net/ipv4/arp.c:1016 [inline]
arp_req_set+0x430/0x10a0 net/ipv4/arp.c:1032
arp_ioctl+0x8d4/0xb60 net/ipv4/arp.c:1232
inet_ioctl+0x4ef/0x820 net/ipv4/af_inet.c:947
sock_do_ioctl net/socket.c:1118 [inline]
sock_ioctl+0xa3f/0x13e0 net/socket.c:1235
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:874 [inline]
__se_sys_ioctl+0x2df/0x4a0 fs/ioctl.c:860
__x64_sys_ioctl+0xd8/0x110 fs/ioctl.c:860
do_syscall_x64 arch/x86/entry/common.c:51 [inline]
do_syscall_64+0x54/0xd0 arch/x86/entry/common.c:82
entry_SYSCALL_64_after_hwframe+0x44/0xae
CPU: 1 PID: 20001 Comm: syz-executor.0 Not tainted 5.16.0-rc3-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Fixes: 62dd93181aaa ("[IPV6] NDISC: Set per-entry is_router flag in Proxy NA.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Roopa Prabhu <roopa@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20211206165329.1049835-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
can-next 2021-12-08
The first patch is by Vincent Mailhol and replaces the custom CAN
units with generic one form linux/units.h.
The next 3 patches are by Evgeny Boger and add Allwinner R40 support
to the sun4i CAN driver.
Andy Shevchenko contributes 4 patches to the hi311x CAN driver,
consisting of cleanups and converting the driver to the device
property API.
* tag 'linux-can-next-for-5.17-20211208' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next:
can: hi311x: hi3110_can_probe(): convert to use dev_err_probe()
can: hi311x: hi3110_can_probe(): make use of device property API
can: hi311x: hi3110_can_probe(): try to get crystal clock rate from property
can: hi311x: hi3110_can_probe(): use devm_clk_get_optional() to get the input clock
ARM: dts: sun8i: r40: add node for CAN controller
can: sun4i_can: add support for R40 CAN controller
dt-bindings: net: can: add support for Allwinner R40 CAN controller
can: bittiming: replace CAN units with the generic ones from linux/units.h
====================
Link: https://lore.kernel.org/r/20211208125055.223141-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
1) Fix bogus compilter warning in nfnetlink_queue, from Florian Westphal.
2) Don't run conntrack on vrf with !dflt qdisc, from Nicolas Dichtel.
3) Fix nft_pipapo bucket load in AVX2 lookup routine for six 8-bit
groups, from Stefano Brivio.
4) Break rule evaluation on malformed TCP options.
5) Use socat instead of nc in selftests/netfilter/nft_zones_many.sh,
also from Florian
6) Fix KCSAN data-race in conntrack timeout updates, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf:
netfilter: conntrack: annotate data-races around ct->timeout
selftests: netfilter: switch zone stress to socat
netfilter: nft_exthdr: break evaluation if setting TCP option fails
selftests: netfilter: Add correctness test for mac,net set type
nft_set_pipapo: Fix bucket load in AVX2 lookup routine for six 8-bit groups
vrf: don't run conntrack on vrf with !dflt qdisc
netfilter: nfnetlink_queue: silence bogus compiler warning
====================
Link: https://lore.kernel.org/r/20211209000847.102598-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2021-12-08
Yahui adds re-initialization of Flow Director for VF reset.
Paul restores interrupts when enabling VFs.
Dave re-adds bandwidth check for DCBNL and moves DSCP mode check
earlier in the function.
Jesse prevents reporting of dropped packets that occur during
initialization and fixes reporting of statistics which could occur with
frequent reads.
Michal corrects setting of protocol type for UDP header and fixes lack
of differentiation when adding filters for tunnels.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ice: safer stats processing
ice: fix adding different tunnels
ice: fix choosing UDP header type
ice: ignore dropped packets during init
ice: Fix problems with DSCP QoS implementation
ice: rearm other interrupt cause register after enabling VFs
ice: fix FDIR init missing when reset VF
====================
Link: https://lore.kernel.org/r/20211208211144.2629867-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Daniel Borkmann says:
====================
bpf 2021-12-08
We've added 12 non-merge commits during the last 22 day(s) which contain
a total of 29 files changed, 659 insertions(+), 80 deletions(-).
The main changes are:
1) Fix an off-by-two error in packet range markings and also add a batch of
new tests for coverage of these corner cases, from Maxim Mikityanskiy.
2) Fix a compilation issue on MIPS JIT for R10000 CPUs, from Johan Almbladh.
3) Fix two functional regressions and a build warning related to BTF kfunc
for modules, from Kumar Kartikeya Dwivedi.
4) Fix outdated code and docs regarding BPF's migrate_disable() use on non-
PREEMPT_RT kernels, from Sebastian Andrzej Siewior.
5) Add missing includes in order to be able to detangle cgroup vs bpf header
dependencies, from Jakub Kicinski.
6) Fix regression in BPF sockmap tests caused by missing detachment of progs
from sockets when they are removed from the map, from John Fastabend.
7) Fix a missing "no previous prototype" warning in x86 JIT caused by BPF
dispatcher, from Björn Töpel.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
bpf: Add selftests to cover packet access corner cases
bpf: Fix the off-by-two error in range markings
treewide: Add missing includes masked by cgroup -> bpf dependency
tools/resolve_btfids: Skip unresolved symbol warning for empty BTF sets
bpf: Fix bpf_check_mod_kfunc_call for built-in modules
bpf: Make CONFIG_DEBUG_INFO_BTF depend upon CONFIG_BPF_SYSCALL
mips, bpf: Fix reference to non-existing Kconfig symbol
bpf: Make sure bpf_disable_instrumentation() is safe vs preemption.
Documentation/locking/locktypes: Update migrate_disable() bits.
bpf, sockmap: Re-evaluate proto ops when psock is removed from sockmap
bpf, sockmap: Attach map progs to psock early for feature probes
bpf, x86: Fix "no previous prototype" warning
====================
Link: https://lore.kernel.org/r/20211208155125.11826-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Warn on the lack of key exchange during NTLMSSP authentication rather
than aborting it as there are some servers that do not set it in
CHALLENGE message.
Signed-off-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Acked-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
This commit fixes a misunderstanding in commit 4a3e0aeddf09 ("net: dsa:
mv88e6xxx: don't use PHY_DETECT on internal PHY's").
For Marvell DSA switches with the PHY_DETECT bit (for non-6250 family
devices), controls whether the PPU polls the PHY to retrieve the link,
speed, duplex and pause status to update the port configuration. This
applies for both internal and external PHYs.
For some switches such as 88E6352 and 88E6390X, PHY_DETECT has an
additional function of enabling auto-media mode between the internal
PHY and SERDES blocks depending on which first gains link.
The original intention of commit 5d5b231da7ac (net: dsa: mv88e6xxx: use
PHY_DETECT in mac_link_up/mac_link_down) was to allow this bit to be
used to detect when this propagation is enabled, and allow software to
update the port configuration. This has found to be necessary for some
switches which do not automatically propagate status from the SERDES to
the port, which includes the 88E6390. However, commit 4a3e0aeddf09
("net: dsa: mv88e6xxx: don't use PHY_DETECT on internal PHY's") breaks
this assumption.
Maarten Zanders has confirmed that the issue he was addressing was for
an 88E6250 switch, which does not have a PHY_DETECT bit in bit 12, but
instead a link status bit. Therefore, mv88e6xxx_port_ppu_updates() does
not report correctly.
This patch resolves the above issues by reverting Maarten's change and
instead making mv88e6xxx_port_ppu_updates() indicate whether the port
is internal for the 88E6250 family of switches.
Yes, you're right, I'm targeting the 6250 family. And yes, your
suggestion would solve my case and is a better implementation for
the other devices (as far as I can see).
Fixes: 4a3e0aeddf09 ("net: dsa: mv88e6xxx: don't use PHY_DETECT on internal PHY's")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Tested-by: Maarten Zanders <maarten.zanders@mind.be>
Link: https://lore.kernel.org/r/E1muXm7-00EwJB-7n@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Vladimir Oltean says:
====================
Rework DSA bridge TX forwarding offload API
This change set is preparation work for DSA support of bridge FDB
isolation. It replaces struct net_device *dp->bridge_dev with a struct
dsa_bridge *dp->bridge that contains some extra information about that
bridge, like a unique number kept by DSA.
Up until now we computed that number only with the bridge TX forwarding
offload feature, but it will be needed for other features too, like for
isolation of FDB entries belonging to different bridges. Hardware
implementations vary, but one common pattern seems to be the presence of
a FID field which can be associated with that bridge number kept by DSA.
The idea was outlined here:
https://patchwork.kernel.org/project/netdevbpf/patch/20210818120150.892647-16-vladimir.oltean@nxp.com/
(the difference being that with this new proposal, drivers would not
need to call dsa_bridge_num_find, instead the bridge_num would be part
of the struct dsa_bridge :: num passed as argument).
No functional change is intended for drivers that don't already make use
of the bridge TX forwarding offload. I've tested the changes on the
felix, sja1105 and mv88e6xxx drivers, but nonetheless I'm copying all
DSA driver maintainers due to API changes that are taking place.
Compared to v1 and v2, the amount of patches is larger, but the contents
is mostly the same, just split up hopefully a bit better for review.
====================
Link: https://lore.kernel.org/r/20211206165758.1553882-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We don't really need new switch API for these, and with new switches
which intend to add support for this feature, it will become cumbersome
to maintain.
The change consists in restructuring the two drivers that implement this
offload (sja1105 and mv88e6xxx) such that the offload is enabled and
disabled from the ->port_bridge_{join,leave} methods instead of the old
->port_bridge_tx_fwd_{,un}offload.
The only non-trivial change is that mv88e6xxx_map_virtual_bridge_to_pvt()
has been moved to avoid a forward declaration, and the
mv88e6xxx_reg_lock() calls from inside it have been removed, since
locking is now done from mv88e6xxx_port_bridge_{join,leave}.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This is a preparation patch for the removal of the DSA switch methods
->port_bridge_tx_fwd_offload() and ->port_bridge_tx_fwd_unoffload().
The plan is for the switch to report whether it offloads TX forwarding
directly as a response to the ->port_bridge_join() method.
This change deals with the noisy portion of converting all existing
function prototypes to take this new boolean pointer argument.
The bool is placed in the cross-chip notifier structure for bridge join,
and a reference to it is provided to drivers. In the next change, DSA
will then actually look at this value instead of calling
->port_bridge_tx_fwd_offload().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The main desire behind this is to provide coherent bridge information to
the fast path without locking.
For example, right now we set dp->bridge_dev and dp->bridge_num from
separate code paths, it is theoretically possible for a packet
transmission to read these two port properties consecutively and find a
bridge number which does not correspond with the bridge device.
Another desire is to start passing more complex bridge information to
dsa_switch_ops functions. For example, with FDB isolation, it is
expected that drivers will need to be passed the bridge which requested
an FDB/MDB entry to be offloaded, and along with that bridge_dev, the
associated bridge_num should be passed too, in case the driver might
want to implement an isolation scheme based on that number.
We already pass the {bridge_dev, bridge_num} pair to the TX forwarding
offload switch API, however we'd like to remove that and squash it into
the basic bridge join/leave API. So that means we need to pass this
pair to the bridge join/leave API.
During dsa_port_bridge_leave, first we unset dp->bridge_dev, then we
call the driver's .port_bridge_leave with what used to be our
dp->bridge_dev, but provided as an argument.
When bridge_dev and bridge_num get folded into a single structure, we
need to preserve this behavior in dsa_port_bridge_leave: we need a copy
of what used to be in dp->bridge.
Switch drivers check bridge membership by comparing dp->bridge_dev with
the provided bridge_dev, but now, if we provide the struct dsa_bridge as
a pointer, they cannot keep comparing dp->bridge to the provided
pointer, since this only points to an on-stack copy. To make this
obvious and prevent driver writers from forgetting and doing stupid
things, in this new API, the struct dsa_bridge is provided as a full
structure (not very large, contains an int and a pointer) instead of a
pointer. An explicit comparison function needs to be used to determine
bridge membership: dsa_port_offloads_bridge().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move the static inline helpers from net/dsa/dsa_priv.h to
include/net/dsa.h, so that drivers can call functions such as
dsa_port_offloads_bridge_dev(), which will be necessary after the
transition to a more complex bridge structure.
More functions than are needed right now are being moved, but this is
done for uniformity.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently the majority of dsa_port_bridge_dev_get() calls in drivers is
just to check whether a port is under the bridge device provided as
argument by the DSA API.
We'd like to change that DSA API so that a more complex structure is
provided as argument. To keep things more generic, and considering that
the new complex structure will be provided by value and not by
reference, direct comparisons between dp->bridge and the provided bridge
will be broken. The generic way to do the checking would simply be to
do something like dsa_port_offloads_bridge(dp, &bridge).
But there's a problem, we already have a function named that way, which
actually takes a bridge_dev net_device as argument. Rename it so that we
can use dsa_port_offloads_bridge for something else.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The location of the bridge device pointer and number is going to change.
It is not going to be kept individually per port, but in a common
structure allocated dynamically and which will have lockdep validation.
Use the helpers to access these elements so that we have a migration
path to the new organization.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The location of the bridge device pointer and number is going to change.
It is not going to be kept individually per port, but in a common
structure allocated dynamically and which will have lockdep validation.
Create helpers to access these elements so that we have a migration path
to the new organization.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
comparison
The goal of this change is to reduce mv88e6xxx_port_vlan() to a form
where dsa_port_bridge_same() can be used, since the dp->bridge_dev
pointer will be hidden in a future change.
To do that, we observe that the "br" pointer is deduced from a
dp->bridge_dev in both cases (of a physical switch port as well as a
virtual bridge). So instead of keeping the "br" pointer, we can just
keep the "dp" pointer from which "br" gets derived.
In the last iteration over switch ports, we must use another iterator
variable, "other_dp"since now we use the "dp" variable to keep an
indirect reference to the bridge. While at it, the old code used to
filter only the ports which were part of the same switch as "ds".
There exists a dedicated DSA port iterator for that:
dsa_switch_for_each_port (which skips the ports in the tree that belong
to non-local switches), so we can just use that.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
mv88e6xxx_port_check_hw_vlan
Avoid a plethora of dsa_to_port() calls (some hidden behind
dsa_is_*_port and some in plain sight) by keeping two struct dsa_port
references: one to the port passed as argument, and another to the other
ports of the switch that we're iterating over.
This isn't called from the DSA initialization path, so there is no risk
that we have user ports without a dp->slave populated. So the combined
checks that a port isn't a DSA port, a CPU port, or doesn't have a slave
net device (therefore is unused), are strictly equivalent to the simple
check that the port is a user port. This is already handled by the DSA
iterator.
i gets replaced by other_dp->index, dsa_is_*_port calls get replaced by
dsa_port_is_*, and dsa_to_port gets replaced by the respective pointer
directly.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Avoid repeated calls to dsa_to_port() (some hidden behind dsa_is_user_port
and some in plain sight) by keeping two struct dsa_port references: one
to the port passed as argument, and another to the other ports of the
switch that we're iterating over.
dsa_to_port(ds, i) gets replaced by other_dp, i gets replaced by
other_port which is derived from other_dp->index, dsa_is_user_port is
handled by the DSA iterator.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The service where DSA assigns a unique bridge number for each forwarding
domain is useful even for drivers which do not implement the TX
forwarding offload feature.
For example, drivers might use the dp->bridge_num for FDB isolation.
So rename ds->num_fwd_offloading_bridges to ds->max_num_bridges, and
calculate a unique bridge_num for all drivers that set this value.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
I have seen too many bugs already due to the fact that we must encode an
invalid dp->bridge_num as a negative value, because the natural tendency
is to check that invalid value using (!dp->bridge_num). Latest example
can be seen in commit 1bec0f05062c ("net: dsa: fix bridge_num not
getting cleared after ports leaving the bridge").
Convert the existing users to assume that dp->bridge_num == 0 is the
encoding for invalid, and valid bridge numbers start from 1.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This reverts commit 53182e81f47d4ea0c727c49ad23cb782173ab849.
This added tool dependencies on various build systems using %.dtb
targets. Validation will need to be controlled by a kconfig or make
variable instead, but for now let's just revert it.
Signed-off-by: Rob Herring <robh@kernel.org>
|
