| Age | Commit message (Collapse) | Author |
|---|
|
libabikfs.a doesn't exist anymore, so we now need to link with libapi.a.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/1426199953-15324-1-git-send-email-andi@firstfloor.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
architectures
On architectures where the stack grows upwards (CONFIG_STACK_GROWSUP=y,
currently parisc and metag only) stack randomization sometimes leads to crashes
when the stack ulimit is set to lower values than STACK_RND_MASK (which is 8 MB
by default if not defined in arch-specific headers).
The problem is, that when the stack vm_area_struct is set up in fs/exec.c, the
additional space needed for the stack randomization (as defined by the value of
STACK_RND_MASK) was not taken into account yet and as such, when the stack
randomization code added a random offset to the stack start, the stack
effectively got smaller than what the user defined via rlimit_max(RLIMIT_STACK)
which then sometimes leads to out-of-stack situations and crashes.
This patch fixes it by adding the maximum possible amount of memory (based on
STACK_RND_MASK) which theoretically could be added by the stack randomization
code to the initial stack size. That way, the user-defined stack size is always
guaranteed to be at minimum what is defined via rlimit_max(RLIMIT_STACK).
This bug is currently not visible on the metag architecture, because on metag
STACK_RND_MASK is defined to 0 which effectively disables stack randomization.
The changes to fs/exec.c are inside an "#ifdef CONFIG_STACK_GROWSUP"
section, so it does not affect other platformws beside those where the
stack grows upwards (parisc and metag).
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: linux-parisc@vger.kernel.org
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-metag@vger.kernel.org
Cc: stable@vger.kernel.org # v3.16+
|
|
These KERN_<LEVEL> uses are unnecessary with pr_<level> and cause
bad logging output so remove them.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
'asoc/fix/uda1380', 'asoc/fix/wm8960' and 'asoc/fix/wm8994' into asoc-linus
|
|
|
|
|
|
According to referance manual, right justify mode can't
support 32 bit word length.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
wm8960 codec driver missing configure its bit clock and frame clock for codec
master mode, so add support for it. It will calculate a appropriate frequency
dividing ratio according to the system clock, bit clock and frame clock, then
set the corresponding registers.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
According to the RM of wm8958, BCLK DIV 348 doesn't exist, correct it
to 384.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
|
|
'channels' is allocated via kmemdup and it is never freed.
Use 'indio_dev->channels' directly instead, so that we avoid such
memory leak problem.
Reported-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
According to hardware team there should be some delay after
setting channel number, start mode and before setting START.
Add a one microsecond delay for this purpose.
Fixes: 1664f6a5b0c8 ("iio: adc: Cosmic Circuits 10001 ADC driver")
Signed-off-by: Naidu Tellapati <naidu.tellapati@imgtec.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
regulator_get_voltage() returns a non-negative value in case of success,
and a negative error in case of error. Let's fix this.
Fixes: 1664f6a5b0c8 ("iio: adc: Cosmic Circuits 10001 ADC driver")
Signed-off-by: Naidu Tellapati <naidu.tellapati@imgtec.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
At present we are incorrectly setting the register to 0x1 to power up
the ADC. Since it is an active high power down register, we need to set
the register to 0x0 to actually power up. Conversely, writing 0x1 to the
register powers it down.
This commit adds a couple of helpers to make the code clearer and then
use them to do the power-up/power-down properly.
Fixes: 1664f6a5b0c8 ("iio: adc: Cosmic Circuits 10001 ADC driver")
Signed-off-by: Naidu Tellapati <naidu.tellapati@imgtec.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
It should be "RINPUT3" instead of "LINPUT3" route to "Right Input
Mixer".
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
|
|
rt5645_jack_detect doesn't report the correct jack type consistently.
It mistakes OMTP type headset to CTIA type in particular HW design.
Register changes are needed for this issue. This patch can make it
more stable.
Signed-off-by: John Lin <john.lin@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
IRQ of jack and button detection is abnormal if "LDO2" and
"Mic Det Power" power disable in rt5645_jack_detect.
This patch make these two power keep enabled until jack out.
Signed-off-by: John Lin <john.lin@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The power of "micbias1" and "micbias2" are unnecessary for jack detection.
So, we remove it in rt5645_set_jack_detect function.
Signed-off-by: John Lin <john.lin@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We add a calibration function and call it at the beginning of i2c_probe.
The calibration value will be kept until codec is shutdown. We will reset
the codec after the calibration is finished. So, we set cache_bypass in
the calibration function. The benefit is we can shorter the delay time
in headphone depop.
We also change the register setting in the depop sequence which will
reduce the pop noise in headphone playback.
Signed-off-by: John Lin <john.lin@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Since commit 8b283c025443 ("ARM: exynos4/5: convert pmu wakeup to
stacked domains"), a suspend/resume is not supported on old DT.
Although, rather than printing a warning and continue to boot, the
kernel will segfault just after:
------------[ cut here ]------------
WARNING: CPU: 1 PID: 1 at arch/arm/mach-exynos/suspend.c:726 exynos_pm_init+0x4c/0xc8()
Modules linked in:
CPU: 1 PID: 1 Comm: swapper/0 Not tainted 4.1.0-rc3 #1
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[<c02181c4>] (unwind_backtrace) from [<c0213b2c>] (show_stack+0x10/0x14)
[<c0213b2c>] (show_stack) from [<c0949890>] (dump_stack+0x70/0x8c)
[<c0949890>] (dump_stack) from [<c024f0b0>] (warn_slowpath_common+0x74/0xac)
[<c024f0b0>] (warn_slowpath_common) from [<c024f104>] (warn_slowpath_null+0x1c/0x24)
[<c024f104>] (warn_slowpath_null) from [<c0cf1d28>] (exynos_pm_init+0x4c/0xc8)
[<c0cf1d28>] (exynos_pm_init) from [<c0ceaae8>] (init_machine_late+0x1c/0x28)
[<c0ceaae8>] (init_machine_late) from [<c020aa64>] (do_one_initcall+0x80/0x1d0)
[<c020aa64>] (do_one_initcall) from [<c0ce8d4c>] (kernel_init_freeable+0x10c/0x1d8)
[<c0ce8d4c>] (kernel_init_freeable) from [<c0944a2c>] (kernel_init+0x8/0xe4)
[<c0944a2c>] (kernel_init) from [<c0210e60>] (ret_from_fork+0x14/0x34)
---[ end trace 335bd937d409f3c7 ]---
Outdated DT detected, suspend/resume will NOT work
Unable to handle kernel NULL pointer dereference at virtual address 00000608
pgd = c0204000
[00000608] *pgd=00000000
Internal error: Oops: 5 [#1] SMP ARM
Modules linked in:
CPU: 1 PID: 1 Comm: swapper/0 Tainted: G W 4.1.0-rc3 #1
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
task: db06c000 ti: db05a000 task.ti: db05a000
PC is at exynos_pm_init+0x6c/0xc8
LR is at exynos_pm_init+0x54/0xc8
pc : [<c0cf1d48>] lr : [<c0cf1d30>] psr: 60000113
sp : db05bee8 ip : 00000000 fp : 00000000
r10: 00000116 r9 : c0dab2d4 r8 : d8d5f440
r7 : c0db7ad8 r6 : c0db7ad8 r5 : 00000000 r4 : c0ceaacc
r3 : c0eb2aec r2 : c0951e40 r1 : 00000000 r0 : c0eb2acc
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel
Control: 10c5387d Table: 6020406a DAC: 00000015
Process swapper/0 (pid: 1, stack limit = 0xdb05a220)
Stack: (0xdb05bee8 to 0xdb05c000)
bee0: c0db7ad8 c0d8fe34 c0cf17c8 c0ceaae8 00000000 c020aa64
bf00: 00000033 c09580b8 db04fd00 c0ed79a4 c0eb1000 c0ce8588 c0ca2bc4 c0353fcc
bf20: 00000000 c0df358c 60000113 00000000 dbfffba4 00000000 c0ca2bc4 c026654c
bf40: c0b80134 c0ca1a64 00000007 00000007 c0df3554 c0d6c2f4 00000007 c0d6c2d4
bf60: c0eb1000 c0ce8588 c0dab2d4 00000116 00000000 c0ce8d4c 00000007 00000007
bf80: c0ce8588 c0944a24 00000000 c0944a24 00000000 00000000 00000000 00000000
bfa0: 00000000 c0944a2c 00000000 c0210e60 00000000 00000000 00000000 00000000
bfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
bfe0: 00000000 00000000 00000000 00000000 00000013 00000000 00000000 00000000
[<c0cf1d48>] (exynos_pm_init) from [<c0ceaae8>] (init_machine_late+0x1c/0x28)
[<c0ceaae8>] (init_machine_late) from [<c020aa64>] (do_one_initcall+0x80/0x1d0)
[<c020aa64>] (do_one_initcall) from [<c0ce8d4c>] (kernel_init_freeable+0x10c/0x1d8)
[<c0ce8d4c>] (kernel_init_freeable) from [<c0944a2c>] (kernel_init+0x8/0xe4)
[<c0944a2c>] (kernel_init) from [<c0210e60>] (ret_from_fork+0x14/0x34)
Code: e59f005c e59220c0 e5901000 e5832000 (e591e608)
---[ end trace 335bd937d409f3c8 ]---
This is happening because pmu_base_addr is only initialized when the
PMU is an interrupt controller. It's not the case on old DT.
Signed-off-by: Julien Grall <julien.grall@citrix.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
Since commit 1c6c69525b40eb76de8adf039409722015927dc3 ("genirq: Reject
bogus threaded irq requests") threaded IRQs without a primary handler
need to be requested with IRQF_ONESHOT, otherwise the request will fail.
So pass the IRQF_ONESHOT flag in this case.
The semantic patch that makes this change is available
in scripts/coccinelle/misc/irqf_oneshot.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Since commit 1c6c69525b40eb76de8adf039409722015927dc3 ("genirq: Reject
bogus threaded irq requests") threaded IRQs without a primary handler
need to be requested with IRQF_ONESHOT, otherwise the request will fail.
So pass the IRQF_ONESHOT flag in this case.
The semantic patch that makes this change is available
in scripts/coccinelle/misc/irqf_oneshot.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Since commit 1c6c69525b40eb76de8adf039409722015927dc3 ("genirq: Reject
bogus threaded irq requests") threaded IRQs without a primary handler
need to be requested with IRQF_ONESHOT, otherwise the request will fail.
So pass the IRQF_ONESHOT flag in this case.
The semantic patch that makes this change is available
in scripts/coccinelle/misc/irqf_oneshot.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Since commit 1c6c69525b40eb76de8adf039409722015927dc3 ("genirq: Reject
bogus threaded irq requests") threaded IRQs without a primary handler
need to be requested with IRQF_ONESHOT, otherwise the request will fail.
So pass the IRQF_ONESHOT flag in this case.
The semantic patch that makes this change is available
in scripts/coccinelle/misc/irqf_oneshot.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Since commit 1c6c69525b40eb76de8adf039409722015927dc3 ("genirq: Reject
bogus threaded irq requests") threaded IRQs without a primary handler
need to be requested with IRQF_ONESHOT, otherwise the request will fail.
So pass the IRQF_ONESHOT flag in this case.
The semantic patch that makes this change is available
in scripts/coccinelle/misc/irqf_oneshot.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Normally we don't support 12kHz, 24kHz in audio driver, alsa didn't
have formal definition of 12kHz, 24kHz, but alsa supply a way to
support these sample rates. And add 176.4kHz and 192kHz support.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When sai works on master mode, set its bit clock and frame clock.
SAI has 4 MCLK source, bus clock, MCLK1, MCLK2 and MCLK3. fsl_sai_set_bclk
will select proper MCLK source, then calculate and set the bit clock divider.
After fsl_sai_set_bclk, enable the selected mclk in hw_params(), and add
hw_free() to disable the mclk.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add devicetree support for bluetooth SCO link codec.
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The Marvell mwifiex driver prevents the system to enter into a suspend
state if the card power is not preserved during a suspend/resume cycle.
So Suspend-to-RAM and Suspend-to-idle is failing on Exynos5800 Peach Pi
and Exynos5420 Peach Pit Chromebooks.
Add the keep-power-in-suspend Power Management property to the SDIO/MMC
node so the mwifiex suspend handler doesn't fail and the system is able
to enter into a suspend state.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
When there is prefix specified, currently we will add this prefix in
widget->name, but not in widget->sname.
it causes failure at snd_soc_dapm_link_dai_widgets:
if (!w->sname || !strstr(w->sname, dai_w->name))
because dai_w->name has prefix added, but w->sname does not.
We should also add prefix for stream name
Signed-off-by: Koro Chen <koro.chen@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
|
|
Remove rate constraints from generic ASoC AC'97 CODEC.
Supported rates should be detected and constrained anyway by
AC'97 generic code - was tested with VT1613 CODEC and iMX6 SSI
controller.
This way this driver can be used for platforms which don't need
specialized AC'97 CODEC drivers while at the same avoiding
code duplication from implementing equivalent functionality in
a controller driver.
Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Commit d4988623cc60 ("IB/qib: use arch_phys_wc_add()")
adjusted mtrr inititialization to use the new interface.
Unfortunately, the new interface returns a signed
value and the patch tested the unsigned wc_cookie.
Fix the issue by changing the type of wc_cookie to int. For
the success case the ret left at zero to avoid
a warning from the caller. For failure wc_cookie
is used as the ret.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
devm_gpiod_get_optional is equivalent to devm_gpiod_get(), except that
when no GPIO was assigned to the requested function it will return NULL.
This is convenient for drivers that need to handle optional GPIOs.
I just checked the code in commit 34d7c3905adb9a9
("ASoC: improve usage of gpiod API") and found that it should use
devm_gpiod_get_optional rather than devm_gpiod_get here.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
devm_gpiod_get_optional() is equivalent to devm_gpiod_get(), except that
when no GPIO was assigned to the requested function it will return NULL.
This is convenient for drivers that need to handle optional GPIOs.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
The string iwpm_ulib_name is recorded in a nlmsg as a netlink attribute.
Without this fix parsing of the nlmsg by the userspace port mapper service fails
because of unknown attribute length, causing the port mapper service not to
register the client, which has sent the nlmsg.
Signed-off-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com>
Cc: <stable@vger.kernel.org> #v3.16
Reviewed-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Commit 46490b572544 ("MIPS: kernel: elf: Improve the overall ABI and FPU
mode checks") reworked the ELF FP ABI mode selection logic, but when
CONFIG_MIPS_O32_FP64_SUPPORT is enabled it breaks the use of binaries
which have no PT_MIPS_ABIFLAGS program header & associated
.MIPS.abiflags section.
A default mode is selected based upon whether the ELF contains MIPS32 or
MIPS64 code, but that selection is made in arch_elf_pt_proc.
arch_elf_pt_proc only executes when a PT_MIPS_ABIFLAGS program header is
found. If one is not found then arch_elf_pt_proc is never called, and no
default overall_fp_mode value is selected. When arch_check_elf is
called, both abi0 & abi1 are MIPS_ABI_FP_UNKNOWN which leads to both
prog_req & interp_req being set to none_req. none_req matches none of
the conditions for mode selection at the end of arch_check_elf, so
overall_fp_mode is left untouched. Finally once mips_set_personality_fp
is called the BUG() in the default case is then hit & the kernel likely
panics.
Fix this by moving the selection of a default overall mode to the start
of arch_check_elf, which runs once per ELF executed regardless of
whether it has a PT_MIPS_ABIFLAGS program header.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Matthew Fortune <matthew.fortune@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org # v4.0+
Patchwork: http://patchwork.linux-mips.org/patch/9978/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Commit d795ef9aa831 ("arm64: perf: don't warn about missing
interrupt-affinity property for PPIs") added a check for PPIs so that
we avoid parsing the interrupt-affinity property for these naturally
affine interrupts.
Unfortunately, this check can trigger an early (successful) return and
we will leak the irqs array. This patch fixes the issue by reordering
the code so that the check is performed before any independent
allocation.
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
This patch fixes a compiler warning in gemini_restart()
issued by commit 7b6d864b48d9 ("reboot:arm: reboot_mode
changes from char to enum reboot_mode").
arch/arm/mach-gemini/board-rut1xx.c:93:2: warning: initialization from incompatible pointer type
The warning is harmless, and the patch does not need to
be backported to stable kernels.
Fixes: 7b6d864b48d ("reboot:arm: reboot_mode changes from char to enum reboot_mode.")
Signed-off-by: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge "Few fixes for omap clocks, PRM and hwmod code" from Tony Lindgren:
- Fix bogus comparison of struct clk pointers, turns out
we can fix it by just removing the comparison
- Fix am437 hardreset implementation and remove boottime
warnings by adding the VPFE hwmod data
- Regression fix for am43xx PRM code, simplify things
by reusing the omap4 PRM implementation
* tag 'omap-for-v4.1/fixes-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Remove bogus struct clk comparison for timer clock
ARM: AM33xx+: hwmod: re-use omap4 implementations for reset functionality
ARM: OMAP4+: PRM: add support for passing status register/bit info to reset
ARM: AM43xx: hwmod: add VPFE hwmod entries
|
|
Emulex developers' email addresses are now "@avagotech" instead of
"@emulex". I'm also replacing Subbu with Padmanabh and Sriharsha in the
maintainers list. The driver's heading was outdated and did not include
some of the chip types (BE3, Lancer and Skyhawk) that the driver has
been supporting for a longtime. I've updated this too.
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 9fd85eb502a7 ("ARM: pmu: add support for interrupt-affinity
property") added an optional "interrupt-affinity" property, to specify
the CPU affinity for each SPI listed in the interrupts property.
Without this property, we get this boot warning:
CPU PMU: Failed to parse <no-node>/interrupt-affinity[0]
This patch adds interrupt-affinity to the PMU node in the
vexpress-ca15_a7(a.k.a TC2) device tree.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Commit 9fd85eb502a7 ("ARM: pmu: add support for interrupt-affinity
property") added an optional "interrupt-affinity" property, to specify
the CPU affinity for each SPI listed in the interrupts property.
Without this property, we get this boot warning:
CPU PMU: Failed to parse <no-node>/interrupt-affinity[0]
This patch adds interrupt-affinity to the PMU node in the
vexpress-v2p-ca9 device tree.
Signed-off-by: Robert Schwebel <r.schwebel@pengutronix.de>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Commit d9d1f3e2d711 ("ARM: l2c: check that DT files specify the required
"cache-unified" property") mandates to specify this required property.
Without this property, we get this boot warning:
"L2C: device tree omits to specify unified cache"
This patch adds "cache-unified" property to L2 cache node in vexpress
CA9 device tree.
Signed-off-by: Robert Schwebel <r.schwebel@pengutronix.de>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The clock generator in IOFPGA generates the two source clocks: 32kHz and
1MHz for the SP810 System Controller.
The SP810 System Controller selects 32kHz or 1MHz as the sources for
TIM_CLK[3:0], the SP804 timer clocks. The powerup default is 32kHz but
the maximum of "refclk" and "timclk" is chosen by the SP810 driver.
This patch adds support for SP810 system controller and also fixes the
SP804 timer clock frequency.
However the SP804 driver needs to be enabled on ARM64 to test this,
which requires SP804 driver to be moved out of arch/arm.
Fixes: 71f867ec130e ("arm64: Add Juno board device tree.")
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Back in business.
New place for my repo on github
Signed-off-by: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into fixes
Merge "ARM: tegra: Device tree fixes for v4.1-rc3" from Thierry Reding:
This contains a fix for a bug that was introduced a couple of months ago
by a patch that git misapplied because of a lack of context.
* tag 'tegra-for-4.1-fixes-for-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: Correct which USB controller has the UTMI pad registers
|
|
The mapping range is inclusive between starting and ending addresses.
Signed-off-by: Christian König <christian.koenig@amd.com>
CC: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
When CONFIG_DEBUG_LOCK_ALLOC is defined, mutex magic is compared and
warned for (l->magic != l), here l is the address of mutex pointer.
In hid-sensor-hub as part of hsdev creation, a per hsdev mutex is
initialized during MFD cell creation. This hsdev, which contains, mutex
is part of platform data for the a cell. But platform_data is copied
in platform_device_add_data() in platform.c. This copy will copy the
whole hsdev structure including mutex. But once copied the magic
will no longer match. So when client driver call
sensor_hub_input_attr_get_raw_value, this will trigger mutex warning.
So to avoid this allocate mutex dynamically. This will be same even
after copy.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
If a driver does not set interrupt triggering type when it calls
request_irq(), it means use the pin as the hardware/firmware has
configured it. There are some drivers doing this. One example is
drivers/input/serio/i8042.c that requests the interrupt like:
error = request_irq(I8042_KBD_IRQ, i8042_interrupt, IRQF_SHARED,
"i8042", i8042_platform_device);
It assumes the interrupt is already properly configured. This is true in
case of interrupts connected to the IO-APIC. However, some Intel
Braswell/Cherryview based machines use a GPIO here instead for the internal
keyboard controller.
This is a problem because even if the pin/interrupt is properly configured,
the irqchip ->irq_set_type() will never be called as the triggering flags
are 0. Because of that we do not have correct interrupt flow handler set
for the interrupt.
Fix this by adding a custom ->irq_startup() that checks if the interrupt
has no triggering type set and in that case read the type directly from the
hardware and install correct flow handler along with the mapping.
Reported-by: Jagadish Krishnamoorthy <jagadish.krishnamoorthy@intel.com>
Reported-by: Freddy Paul <freddy.paul@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch fixes an inverted return value of the gpio get_direction
function.
The wrong value causes the direction sysfs entry and GPIO debugfs file
to indicate incorrect GPIO direction settings. In some cases it also
prevents setting GPIO output values.
The problem is also present in all other stable kernel versions since
linux-3.12.
Cc: Stable <stable@vger.kernel.org> # v3.12+
Reported-by: Jochen Henneberg <jh@henneberg-systemdesign.com>
Signed-off-by: Michael Brunner <michael.brunner@kontron.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
