| Age | Commit message (Collapse) | Author |
|---|
|
Since the introduction of BIOS fb preservation, circa 3.17, we began
encountering a failure during boot when trying to use force-detect
before GEM was initialised. That bug is from
commit 7fad798e16fecddd41c6a91728a09f0b9507e40c
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Jul 4 17:51:47 2012 +0200
drm/i915: ensure the force pipe A quirk is actually followed
but investigation of the affected machine revealed that it was using a
PIPE-A quirk even though it was a 945GSE and the quirk is only supposed
to be used to workaround a hardware issue on 830/845. That quirk was
added for this HP Mini in
commit 6b93afc564a5e74b0eaaa46c95f557449951b3b9
Author: Bryce Harrington <bryce@bryceharrington.org>
Date: Wed May 27 03:40:52 2009 -0700
add pipe a force quirk for Dell mini
in order to workaround an issue with the BIOS behaving strangely during
lid-close. Since then we have a much larger hammer to thwart the BIOS
after opening the lid and the PIPE-A quirk is no longer required.
Reported-and-tested-by: Apostolos B. <barz621@gmail.com>
References: https://bugs.freedesktop.org/show_bug.cgi?id=21960
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=87521
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
adapter->tx_ring is set to NULL where rx_ring should be.
Fixes: 5536d2102a2d ("igb: Combine q_vector and ring allocation into a single function")
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When changing the number of rings by ethtool -L, q_vectors are reused,
which causes oops because of uninitialized pointers.
- When an rx is reused as a tx, q_vector->rx.ring is not set to NULL, which
misleads igb_poll() to determine that it has an rx ring although it
actually points to the tx ring.
- When a tx is reused as an rx, q_vector->rx.ring->skb
(q_vector->ring[0].skb) has a value that was used as tx_stats before.
Fix these problems by zeroing it out on reuseing it.
Fixes: 02ef6e1d0b00 ("igb: Fix queue allocation method to accommodate changing during runtime")
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Current code uses wrong mask when setting RT5645_DMIC_2_DP_GPIO12 bit,
fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch adds the ACPI match ID for rt5645/5650 codec
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Without the cacheline alignment, the readings will occasionally incorrectly
return 0.
Signed-off-by: Michael Welling <mwelling@ieee.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
The sink rate read from supported link rate table is in KHz as per spec
while in drm, the saved clock is in deca-KHz. So divide the link rate by
10 before storing.
Reading of rates was added by:
commit fc0f8e25318f ("drm/i915/skl: Read sink supported rates from edp
panel")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
This reverts commit 3a61e97563d78a2ca10752902449570d8433ce76.
The Logitech TK820 seems to be affected by a firmware bug which
delays the sending of the keys (pressed, or released, which triggers
a key-repeat) while holding fingers on the touch sensor.
This behavior can be observed while using the mouse emulation mode
if the user moves the finger while typing (highly improbable though).
Holding the finger still while in the mouse emulation mode does
not trigger the key repeat problem.
So better keep things in their previous state to not have to
explain users that the new key-repeat bug they see is a "feature".
Furthermore, I noticed that I disabled the media keys whith
this patch. Sorry, my bad.
I think it is best to revert the patch, in all the current
versions it has been shipped.
Cc: <stable@vger.kernel.org> # v3.19 and above
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Ensure that the asm code finalization path is not triggered when
invoked via final(), since it already takes care of that itself.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Ensure that the asm code finalization path is not triggered when
invoked via final(), since it already takes care of that itself.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The arm64 CRC32 (not CRC32c) implementation was not quite doing
the same thing as the generic one. Fix that.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Steve Capper <steve.capper@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The only caller to this function (__print_array) was getting it wrong by
passing the array length instead of buffer length. As the element size
was already being passed for other reasons it seems reasonable to push
the calculation of buffer length into the function.
Link: http://lkml.kernel.org/r/1430320727-14582-1-git-send-email-alex.bennee@linaro.org
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
We were passing a flags value that differed from the intention in commit
2b108268006e ("Btrfs: don't use highmem for free space cache pages").
This caused problems in a ARM machine, leaving btrfs unusable there.
Reported-by: Merlijn Wajer <merlijn@wizzup.org>
Tested-by: Merlijn Wajer <merlijn@wizzup.org>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Chris Mason <clm@fb.com>
|
|
Before commit 035a61c314eb ("clk: Make clk API return per-user
struct clk instances") we acquired the enable_lock in
__clk_set_parent_{before,after}() by means of calling
clk_enable(). After commit 035a61c314eb we use clk_core_enable()
in place of the clk_enable(), and clk_core_enable() doesn't
acquire the enable_lock. This opens up a race condition between
clk_set_parent() and clk_enable(). Fix it.
Fixes: 035a61c314eb ("clk: Make clk API return per-user struct clk instances")
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen bug fixes from David Vrabel:
- fix blkback regression if using persistent grants
- fix various event channel related suspend/resume bugs
- fix AMD x86 regression with X86_BUG_SYSRET_SS_ATTRS
- SWIOTLB on ARM now uses frames <4 GiB (if available) so device only
capable of 32-bit DMA work.
* tag 'for-linus-4.1b-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen: Add __GFP_DMA flag when xen_swiotlb_init gets free pages on ARM
hypervisor/x86/xen: Unset X86_BUG_SYSRET_SS_ATTRS on Xen PV guests
xen/events: Set irq_info->evtchn before binding the channel to CPU in __startup_pirq()
xen/console: Update console event channel on resume
xen/xenbus: Update xenbus event channel on resume
xen/events: Clear cpu_evtchn_mask before resuming
xen-pciback: Add name prefix to global 'permissive' variable
xen: Suspend ticks on all CPUs during suspend
xen/grant: introduce func gnttab_unmap_refs_sync()
xen/blkback: safely unmap purge persistent grants
|
|
Block drivers are responsible for calling flush_dcache_page() on each
BIO request. This operation keeps the I$ coherent with the D$ on
architectures that don't have hardware coherency support. Without this
flush, random crashes are seen when executing user programs from an ext4
filesystem backed by a ubiblock device.
This patch is based on the change implemented in commit 2d4dc890b5c8
("block: add helpers to run flush_dcache_page() against a bio and a
request's pages").
Fixes: 9d54c8a33eec ("UBI: R/O block driver on top of UBI volumes")
Signed-off-by: Kevin Cernekee <cernekee@chromium.org>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
With this machines can now configure TDM settings for SSP port using
set_tdm_slot API
Signed-off-by: Praveen Diwakar <praveen.diwakar@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
With this machines can configure the PCM format applied on SSP port using
the set_fmt API
Signed-off-by: Praveen Diwakar <praveen.diwakar@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We have the SSP defaults now and we need to load then in hw_params callback
of BE SSP DAI ops.
Signed-off-by: Praveen Diwakar <praveen.diwakar@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
So right now SSP configuration is statically coded in the driver. While we
would like to keep this configuration intact for the users who are using
these defaults, we need to provide a way for users to program it.
So create a local value in driver structure which is populate with default
value for now
Signed-off-by: Praveen Diwakar <praveen.diwakar@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The current ssp configuration was not configuring the frame sync polarity
and data polarity. Some codecs do need these different so add them in ssp
configuration now
Signed-off-by: Praveen Diwakar <praveen.diwakar@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"EFI fixes, and FPU fix, a ticket spinlock boundary condition fix and
two build fixes"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/fpu: Always restore_xinit_state() when use_eager_cpu()
x86: Make cpu_tss available to external modules
efi: Fix error handling in add_sysfs_runtime_map_entry()
x86/spinlocks: Fix regression in spinlock contention detection
x86/mm: Clean up types in xlate_dev_mem_ptr()
x86/efi: Store upper bits of command line buffer address in ext_cmd_line_ptr
efivarfs: Ensure VariableName is NUL-terminated
|
|
Use the card DAPM context instead of the CODEC DAPM context since only card
level widgets are accessed here.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We can know if dmic is used by reading the value of dmic1_data_pin
and dmic2_data_pin. Also IRQ must be used if codec JD or button
detection function is used. So, dmic_en and en_jd_func can be remove
from platform data.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Mostly tooling fixes, but also an uncore PMU driver fix and an uncore
PMU driver hardware-enablement addition"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf probe: Fix segfault if passed with ''.
perf report: Fix -T/--threads option to work again
perf bench numa: Fix immediate meeting of convergence condition
perf bench numa: Fixes of --quiet argument
perf bench futex: Fix hung wakeup tasks after requeueing
perf probe: Fix bug with global variables handling
perf top: Fix a segfault when kernel map is restricted.
tools lib traceevent: Fix build failure on 32-bit arch
perf kmem: Fix compiles on RHEL6/OL6
tools lib api: Undefine _FORTIFY_SOURCE before setting it
perf kmem: Consistently use PRIu64 for printing u64 values
perf trace: Disable events and drain events when forked workload ends
perf trace: Enable events when doing system wide tracing and starting a workload
perf/x86/intel/uncore: Move PCI IDs for IMC to uncore driver
perf/x86/intel/uncore: Add support for Intel Haswell ULT (lower power Mobile Processor) IMC uncore PMUs
perf/x86/intel: Add cpu_(prepare|starting|dying) for core_pmu
|
|
"IF1 DAC0" and "IF1 DAC3" are used in rt5645_dapm_routes but missing
in rt5645_dapm_widgets.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull RCU fix from Ingo Molnar:
"An RCU Kconfig fix that eliminates an annoying interactive kconfig
question for CONFIG_RCU_TORTURE_TEST_SLOW_INIT"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
rcu: Control grace-period delays directly from value
|
|
The driver does not use any CODEC specific constructs anymore. Convert it
to snd_soc_component.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use a DAPM auto-disable demux to model the Mode control which affects the
routing of the input pin to the output pins. This allows us to remove the
custom code for handling the Mode control.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
A demux is conceptually similar to a mux. Where a mux has multiple input
and one output and selects one of the inputs to be connected to the output,
the demux has one input and multiple outputs and selects one of the outputs
to which the input gets connected.
This similarity makes it straight forward to support them in DAPM using the
existing mux support, we only need to swap sinks and sources when initially
setting up the paths.
The only slightly tricky part is that there can only be one control per
path. Since mixers/muxes are at the sink of a path and a demux is at the
source and both types want a control it is not possible to directly connect
a demux output to a mixer/mux input. The patch adds some sanity checks to
make sure that this does not happen.
Drivers who want to model hardware which directly connects a demux output
to a mixer/mux input can do this by inserting a dummy widget between the
two. E.g.:
{ "Dummy", "Demux Control", "Demux" },
{ "Mixer", "Mixer Control", "Dummy" },
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Currently new widgets are appended to the beginning of the cards widget
list. This has the effect that widgets that are created while iterating
over the widget list in snd_soc_dapm_new_widgets() (like e.g. the
auto-disable widgets) are not covered during that invocation of the
function. If no further invocations of snd_soc_dapm_new_widgets() happen
these widgets will not be fully initialized and e.g. no debugfs entries are
created for them.
By adding new widgets to the end of the widget list we make sure that
widgets that are created in snd_soc_dapm_new_widgets() will still be
handled during the same snd_soc_dapm_new_widgets() invocation and are
always fully initialized.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Currently new widgets are appended to the beginning of the cards widget
list. This has the effect that widgets that are created while iterating
over the widget list in snd_soc_dapm_new_widgets() (like e.g. the
auto-disable widgets) are not covered during that invocation of the
function. If no further invocations of snd_soc_dapm_new_widgets() happen
these widgets will not be fully initialized and e.g. no debugfs entries are
created for them.
By adding new widgets to the end of the widget list we make sure that
widgets that are created in snd_soc_dapm_new_widgets() will still be
handled during the same snd_soc_dapm_new_widgets() invocation and are
always fully initialized.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The mixer core on the Arizona devices is powered up whenever any routing
is non-zero. This patch saves a little power and avoids a few difficult
corner cases (around the mixer core being powered whilst there is no
clock available), by using the autodisable mux functionality to only
write out the settings for the muxes when they are powered up.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Commit 57295073b6ac ("ASoC: dapm: Implement mixer input auto-disable")
added support for autodisable controls, controls whose values are only
written to the hardware when their respective widgets are powered up.
But it only added support for controls based on the mixer abstraction.
This patch add support for mux controls (DAPM controls based on the
enum abstraction) to be auto-disabled as well. As each mux can only have
a single control, there is no need to tie the autodisable widget to the
inputs (as is done for the mixer controls) it can be tided directly to
the mux widget itself.
Note that it is assumed that the first entry in a autodisable mux
control will always represent the off state for the mux and is what the
mux will be set to whilst it is disabled.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This makes it a little easier to follow what is happening in debugfs.
Additionally is also useful in facilitating work to add autodisable
muxes because the control name is already used for the mux widget and
thus shouldn't be reused for the autodisable widget.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
xnitmes is clearly intended to be xnitems, but all other macros just
refer to this as xitems, so change it to that.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Using sendfile with below small program to get MD5 sums of some files,
it appear that big files (over 64kbytes with 4k pages system) get a
wrong MD5 sum while small files get the correct sum.
This program uses sendfile() to send a file to an AF_ALG socket
for hashing.
/* md5sum2.c */
#include <stdio.h>
#include <stdlib.h>
#include <unistd.h>
#include <string.h>
#include <fcntl.h>
#include <sys/socket.h>
#include <sys/stat.h>
#include <sys/types.h>
#include <linux/if_alg.h>
int main(int argc, char **argv)
{
int sk = socket(AF_ALG, SOCK_SEQPACKET, 0);
struct stat st;
struct sockaddr_alg sa = {
.salg_family = AF_ALG,
.salg_type = "hash",
.salg_name = "md5",
};
int n;
bind(sk, (struct sockaddr*)&sa, sizeof(sa));
for (n = 1; n < argc; n++) {
int size;
int offset = 0;
char buf[4096];
int fd;
int sko;
int i;
fd = open(argv[n], O_RDONLY);
sko = accept(sk, NULL, 0);
fstat(fd, &st);
size = st.st_size;
sendfile(sko, fd, &offset, size);
size = read(sko, buf, sizeof(buf));
for (i = 0; i < size; i++)
printf("%2.2x", buf[i]);
printf(" %s\n", argv[n]);
close(fd);
close(sko);
}
exit(0);
}
Test below is done using official linux patch files. First result is
with a software based md5sum. Second result is with the program above.
root@vgoip:~# ls -l patch-3.6.*
-rw-r--r-- 1 root root 64011 Aug 24 12:01 patch-3.6.2.gz
-rw-r--r-- 1 root root 94131 Aug 24 12:01 patch-3.6.3.gz
root@vgoip:~# md5sum patch-3.6.*
b3ffb9848196846f31b2ff133d2d6443 patch-3.6.2.gz
c5e8f687878457db77cb7158c38a7e43 patch-3.6.3.gz
root@vgoip:~# ./md5sum2 patch-3.6.*
b3ffb9848196846f31b2ff133d2d6443 patch-3.6.2.gz
5fd77b24e68bb24dcc72d6e57c64790e patch-3.6.3.gz
After investivation, it appears that sendfile() sends the files by blocks
of 64kbytes (16 times PAGE_SIZE). The problem is that at the end of each
block, the SPLICE_F_MORE flag is missing, therefore the hashing operation
is reset as if it was the end of the file.
This patch adds SPLICE_F_MORE to the flags when more data is pending.
With the patch applied, we get the correct sums:
root@vgoip:~# md5sum patch-3.6.*
b3ffb9848196846f31b2ff133d2d6443 patch-3.6.2.gz
c5e8f687878457db77cb7158c38a7e43 patch-3.6.3.gz
root@vgoip:~# ./md5sum2 patch-3.6.*
b3ffb9848196846f31b2ff133d2d6443 patch-3.6.2.gz
c5e8f687878457db77cb7158c38a7e43 patch-3.6.3.gz
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Way back, when the world was a simpler place and there was no war, no
evil, and no kernel bugs, there was just a single pinctrl lock. That
was how the world was when (57291ce pinctrl: core device tree mapping
table parsing support) was written. In that case, there were
instances where the pinctrl mutex was already held when
pinctrl_register_map() was called, hence a "locked" parameter was
passed to the function to indicate that the mutex was already locked
(so we shouldn't lock it again).
A few years ago in (42fed7b pinctrl: move subsystem mutex to
pinctrl_dev struct), we switched to a separate pinctrl_maps_mutex.
...but (oops) we forgot to re-think about the whole "locked" parameter
for pinctrl_register_map(). Basically the "locked" parameter appears
to still refer to whether the bigger pinctrl_dev mutex is locked, but
we're using it to skip locks of our (now separate) pinctrl_maps_mutex.
That's kind of a bad thing(TM). Probably nobody noticed because most
of the calls to pinctrl_register_map happen at boot time and we've got
synchronous device probing. ...and even cases where we're
asynchronous don't end up actually hitting the race too often. ...but
after banging my head against the wall for a bug that reproduced 1 out
of 1000 reboots and lots of looking through kgdb, I finally noticed
this.
Anyway, we can now safely remove the "locked" parameter and go back to
a war-free, evil-free, and kernel-bug-free world.
Fixes: 42fed7ba44e4 ("pinctrl: move subsystem mutex to pinctrl_dev struct")
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Make sure that xen_swiotlb_init allocates buffers that are DMA capable
when at least one memblock is available below 4G. Otherwise we assume
that all devices on the SoC can cope with >4G addresses. We do this on
ARM and ARM64, where dom0 is mapped 1:1, so pfn == mfn in this case.
No functional changes on x86.
From: Chen Baozi <baozich@gmail.com>
Signed-off-by: Chen Baozi <baozich@gmail.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Tested-by: Chen Baozi <baozich@gmail.com>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
|
|
At some point with all the GPIO clean-up we've broken the
MPUIO interrupts. Those are just a little bit different from
the GPIO interrupts, so we can fix it up just by setting
different irqchip functions for it. And then we can just
remove all old code trying to do the same.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Javier Martinez Canillas <javier@dowhile0.org>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
During kernel boot, it will try to read some logical sectors
of each block device node for the possible partition table.
But since RPMB partition is special and can not be accessed
by normal eMMC read / write CMDs, it will cause below error
messages during kernel boot:
...
mmc0: Got data interrupt 0x00000002 even though no data operation was in progress.
mmcblk0rpmb: error -110 transferring data, sector 0, nr 32, cmd response 0x900, card status 0xb00
mmcblk0rpmb: retrying using single block read
mmcblk0rpmb: timed out sending r/w cmd command, card status 0x400900
mmcblk0rpmb: timed out sending r/w cmd command, card status 0x400900
mmcblk0rpmb: timed out sending r/w cmd command, card status 0x400900
mmcblk0rpmb: timed out sending r/w cmd command, card status 0x400900
mmcblk0rpmb: timed out sending r/w cmd command, card status 0x400900
mmcblk0rpmb: timed out sending r/w cmd command, card status 0x400900
end_request: I/O error, dev mmcblk0rpmb, sector 0
Buffer I/O error on device mmcblk0rpmb, logical block 0
end_request: I/O error, dev mmcblk0rpmb, sector 8
Buffer I/O error on device mmcblk0rpmb, logical block 1
end_request: I/O error, dev mmcblk0rpmb, sector 16
Buffer I/O error on device mmcblk0rpmb, logical block 2
end_request: I/O error, dev mmcblk0rpmb, sector 24
Buffer I/O error on device mmcblk0rpmb, logical block 3
...
This patch will discard the access request in eMMC queue if
it is RPMB partition access request. By this way, it avoids
trigger above error messages.
Fixes: 090d25fe224c ("mmc: core: Expose access to RPMB partition")
Signed-off-by: Yunpeng Gao <yunpeng.gao@intel.com>
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Tested-by: Michael Shigorin <mike@altlinux.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
rt5650 codec supports 4 buttons detections so enabled it
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into asoc-intel
|
|
of_match_device() checks if dev->of_node is NULL, so we don't need to do
it again in the probe function.
Signed-off-by: Kevin Cernekee <cernekee@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
f9fd54f22e ("mmc: sh_mmcif: Use msecs_to_jiffies() for host->timeout")
changed the timeout value from 1000 jiffies to 1s. In the case where
HZ is 1000 the values are the same. However, for smaller HZ values the
timeout is now smaller, 1s instead of 10s in the case of HZ=100.
Since the timeout occurs in spite of a normal data transfer a timeout of
10s seems more appropriate. This restores the previous timeout in the
case where HZ=100 and results in an increase over the previous timeout
for larger values of HZ.
Fixes: f9fd54f22e ("mmc: sh_mmcif: Use msecs_to_jiffies() for host->timeout")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[horms: rewrote changelog to refer to HZ]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The following commit:
f893959b0898 ("x86/fpu: Don't abuse drop_init_fpu() in flush_thread()")
removed drop_init_fpu() usage from flush_thread(). This seems to break
things for me - the Go 1.4 test suite fails all over the place with
floating point comparision errors (offending commit found through
bisection).
The functional change was that flush_thread() after this commit
only calls restore_init_xstate() when both use_eager_fpu() and
!used_math() are true. drop_init_fpu() (now fpu_reset_state()) calls
restore_init_xstate() regardless of whether current used_math() - apply
the same logic here.
Switch used_math() -> tsk_used_math(tsk) to consistently use the grabbed
tsk instead of current, like in the rest of flush_thread().
Tested-by: Dave Hansen <dave.hansen@intel.com>
Signed-off-by: Bobby Powers <bobbypowers@gmail.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Pekka Riikonen <priikone@iki.fi>
Cc: Quentin Casasnovas <quentin.casasnovas@oracle.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Suresh Siddha <sbsiddha@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: f893959b ("x86/fpu: Don't abuse drop_init_fpu() in flush_thread()")
Link: http://lkml.kernel.org/r/1430147441-9820-1-git-send-email-bobbypowers@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The eDP port A register on PCH split platforms has a slightly different
register layout from the other ports, with bit 6 being either alternate
scrambler reset or reserved, depending on the generation. Our
misinterpretation of the bit as audio has lead to warning.
Fix this by not enabling audio on port A, since none of our platforms
support audio on port A anyway.
v2: DDI doesn't have audio on port A either (Sivakumar Thulasimani)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=89958
Reported-and-tested-by: Chris Bainbridge <chris.bainbridge@gmail.com>
Cc: stable@vger.kernel.org
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mfleming/efi into x86/urgent
Pull EFI fixes from Matt Fleming:
* Avoid garbage names in efivarfs due to buggy firmware by zeroing
EFI variable name. (Ross Lagerwall)
* Stop erroneously dropping upper 32 bits of boot command line pointer
in EFI boot stub and stash them in ext_cmd_line_ptr. (Roy Franz)
* Fix double-free bug in error handling code path of EFI runtime map
code. (Dan Carpenter)
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
A string written by the user may not be zero terminated.
sscanf may read memory beyond the buffer if no zero byte
is found.
For testing build with CONFIG_USB_CHIPIDEA=y, CONFIG_USB_CHIPIDEA_DEBUG=y.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent
Pull perf/urgent fixes from Arnaldo Carvalho de Melo:
- Fix 'perf probe -a' segfault if passed with '' (Wang Nan)
- Fix report -T/--threads option (Namhyung Kim)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
