| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ethernet flow control:
The switch MAC does not consume, nor does it emit pause frames. It
simply forwards them as any other Ethernet frame (and since the DMAC is,
per IEEE spec, 01-80-C2-00-00-01, it means they are filtered as
link-local traffic and forwarded to the CPU, which can't do anything
useful with them).
Duplex:
There is no duplex setting in the SJA1105 MAC. It is known to forward
traffic at line rate on the same port in both directions. Therefore it
must be that it only supports full duplex.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Resetting the switch at runtime is currently done while changing the
vlan_filtering setting (due to the required TPID change).
But reset is asynchronous with packet egress, and the switch core will
not wait for egress to finish before carrying on with the reset
operation.
As a result, a connected PHY such as the BCM5464 would see an
unterminated Ethernet frame and start to jabber (repeat the last seen
Ethernet symbols - jabber is by definition an oversized Ethernet frame
with bad FCS). This behavior is strange in itself, but it also causes
the MACs of some link partners (such as the FRDM-LS1012A) to completely
lock up.
So as a remedy for this situation, when switch reset is required, simply
inhibit Tx on all ports, and wait for the necessary time for the
eventual one frame left in the egress queue (not even the Tx inhibit
command is instantaneous) to be flushed.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If STP is active, this setting is applied on bridged ports each time an
Ethernet link is established (topology changes).
Since the setting is global to the switch and a reset is required to
change it, resets are prevented if the new callback does not change the
value that the hardware already is programmed for.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
VLAN filtering cannot be properly disabled in SJA1105. So in order to
emulate the "no VLAN awareness" behavior (not dropping traffic that is
tagged with a VID that isn't configured on the port), we need to hack
another switch feature: programmable TPID (which is 0x8100 for 802.1Q).
We are reprogramming the TPID to a bogus value which leaves the switch
thinking that all traffic is untagged, and therefore accepts it.
Under a vlan_filtering bridge, the proper TPID of ETH_P_8021Q is
installed again, and the switch starts identifying 802.1Q-tagged
traffic.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are two possible utilizations so far:
- Switch devices that don't support a native insertion/extraction header
on the CPU port may still enjoy the benefits of port isolation with a
custom VLAN tag.
For this, they need to have a customizable TPID in hardware and a new
Ethertype to distinguish between real 802.1Q traffic and the private
tags used for port separation.
- Switches that don't support the deactivation of VLAN awareness, but
still want to have a mode in which they accept all traffic, including
frames that are tagged with a VLAN not configured on their ports, may
use this as a fake to trick the hardware into thinking that the TPID
for VLAN is something other than 0x8100.
What follows after the ETH_P_DSA_8021Q EtherType is a regular VLAN
header (TCI), however there is no other EtherType that can be used for
this purpose and doesn't already have a well-defined meaning.
ETH_P_8021AD, ETH_P_QINQ1, ETH_P_QINQ2 and ETH_P_QINQ3 expect that
another follow-up VLAN tag is present, which is not the case here.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Documentation/devicetree/bindings/net/ethernet.txt is confusing because
it says what the MAC should not do, but not what it *should* do:
* "rgmii-rxid" (RGMII with internal RX delay provided by the PHY, the MAC
should not add an RX delay in this case)
The gap in semantics is threefold:
1. Is it illegal for the MAC to apply the Rx internal delay by itself,
and simplify the phy_mode (mask off "rgmii-rxid" into "rgmii") before
passing it to of_phy_connect? The documentation would suggest yes.
1. For "rgmii-rxid", while the situation with the Rx clock skew is more
or less clear (needs to be added by the PHY), what should the MAC
driver do about the Tx delays? Is it an implicit wild card for the
MAC to apply delays in the Tx direction if it can? What if those were
already added as serpentine PCB traces, how could that be made more
obvious through DT bindings so that the MAC doesn't attempt to add
them twice and again potentially break the link?
3. If the interface is a fixed-link and therefore the PHY object is
fixed (a purely software entity that obviously cannot add clock
skew), what is the meaning of the above property?
So an interpretation of the RGMII bindings was chosen that hopefully
does not contradict their intention but also makes them more applied.
The SJA1105 driver understands to act upon "rgmii-*id" phy-mode bindings
if the port is in the PHY role (either explicitly, or if it is a
fixed-link). Otherwise it always passes the duty of setting up delays to
the PHY driver.
The error behavior that this patch adds is required on SJA1105E/T where
the MAC really cannot apply internal delays. If the other end of the
fixed-link cannot apply RGMII delays either (this would be specified
through its own DT bindings), then the situation requires PCB delays.
For SJA1105P/Q/R/S, this is however hardware supported and the error is
thus only temporary. I created a stub function pointer for configuring
delays per-port on RXC and TXC, and will implement it when I have access
to a board with this hardware setup.
Meanwhile do not allow the user to select an invalid configuration.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently only the (more difficult) first generation E/T series is
supported. Here the TCAM is only 4-way associative, and to know where
the hardware will search for a FDB entry, we need to perform the same
hash algorithm in order to install the entry in the correct bin.
On P/Q/R/S, the TCAM should be fully associative. However the SPI
command interface is different, and because I don't have access to a
new-generation device at the moment, support for it is TODO.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
At this moment the following is supported:
* Link state management through phylib
* Autonomous L2 forwarding managed through iproute2 bridge commands.
IP termination must be done currently through the master netdevice,
since the switch is unmanaged at this point and using
DSA_TAG_PROTO_NONE.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Georg Waibel <georg.waibel@sensor-technik.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This provides an unified API for accessing register bit fields
regardless of memory layout. The basic unit of data for these API
functions is the u64. The process of transforming an u64 from native CPU
encoding into the peripheral's encoding is called 'pack', and
transforming it from peripheral to native CPU encoding is 'unpack'.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Hygon Dhyana CPU has the SMBus device with PCI device ID 0x790b,
which is the same as AMD CZ SMBus device. So add Hygon Dhyana support
to the i2c-piix4 driver by using the code path of AMD.
Signed-off-by: Pu Wen <puwen@hygon.cn>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
We checked I2C calls, but not SMBus. Refactor the helper to an inline
function and use it for both, I2C and SMBus.
Fixes: 9ac6cb5fbb17 ("i2c: add suspended flag and accessors for i2c adapters")
Reported-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
This structure was used intensively for machine specific values
when DT was not used. Since the removal of AVR32 from the kernel,
this structure is only used for passing clocks from PCI macb wrapper, all
other fields being 0.
All other known platforms use DT.
Remove the leftovers but make sure that PCI macb still works as
expected by using default values:
- phydev->irq is set to PHY_POLL by mdiobus_alloc()
- mii_bus->phy_mask is cleared while allocating it
- bp->phy_interface is set to PHY_INTERFACE_MODE_MII if mode not found
in DT.
This simplifies driver probe path and particularly phy handling.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While moving the chunk of code during 739de9a1563a
("net: macb: Reorganize macb_mii bringup"), the declaration of
struct phy_device declaration was kept. It's not useful in this
function as we alrady have a phydev pointer.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Several sound related entries in MAINTAINERS refer to the old git tree
at "git://git.alsa-project.org/alsa-kernel.git". This is no longer used
for development, and Takashi Iwai's kernel.org tree is used instead.
Signed-off-by: Ross Zwisler <zwisler@google.com>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
When there is active traffic through a GID, a QP/AH holds reference to
this GID entry. RoCE GID entry holds reference to its attached
netdevice. Due to this when netdevice is deleted by admin user, its
refcount is not dropped.
Therefore, while deleting RoCE GID, wait for all GID attribute's netdev
users to finish accessing netdev in rcu context. Once all users done
accessing it, release the netdev refcount.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Use core provided API to fill the source MAC address and use
rdma_read_gid_attr_ndev_rcu() to get stable netdev.
This is preparation patch to allow gid attribute to become NULL when
associated net device is removed.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Use rdma_read_gid_attr_ndev_rcu() to access netdevice attached to GID
entry under rcu lock.
This ensures that while working on the netdevice of the GID, it doesn't
get freed.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
To access the netdevice of the GID attribute, use an existing API
rdma_read_gid_attr_ndev_rcu().
This further reduces dependency on open access to netdevice of GID
attribute.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Instead of RoCE drivers figuring out vlan, smac fields while working on
QP/AH, provide a helper routine to read the L2 fields such as vlan_id and
source mac address.
This moves logic from mlx5 driver to core for wider usage for RoCE ports.
This is a preparation patch to allow detaching netdev in subsequent patch.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
GID type to path record type conversion can be done directly based on port
type and gid attribute type. There is no need to find out using indirect
way by its GID attribute's ndev field.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Always consider the skb reserve space based on netdevice of the GID
attribute, regardless of vlan or non vlan netdevice.
Fixes: 43c9fc509fa5 ("rdma_rxe: make rxe work over 802.1q VLAN devices")
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
I thought this script was run via "make tags" etc. but some people
run it directly.
Prior to commit a9a49c2ad9b9 ("kbuild: use $(srctree) instead of
KBUILD_SRC to check out-of-tree build"), in such a usecase, "tree"
was set empty since KBUILD_SRC is undefined. Now, "tree" is set to
"${srctree}/", which is evaluated to "/".
Fix it by taking into account the case where "srctree" is unset.
Link: https://lkml.org/lkml/2019/4/19/501
Fixes: a9a49c2ad9b9 ("kbuild: use $(srctree) instead of KBUILD_SRC to check out-of-tree build")
Reported-by: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
recordmcount.pl uses a set of regular expressions to parse the output of
objdump(1). However, if objdump(1) output is localized, it may not match
the regular expressions, thereby preventing recordmcount.pl from parsing
object files correctly.
In order to allow recordmcount.pl to function correctly regardless of the
current locale settings, set LANG=C when running objdump(1). LC_ALL is
already unset in the top-level Makefile, so it is not necessary to also
override that environment variable.
Signed-off-by: Daniel Dadap <ddadap@nvidia.com>
Reviewed-by: Robert Morell <rmorell@nvidia.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
This sample works well as builtin.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The prompt of CONFIG_SAMPLE_SECCOMP claims this is "loadable module
only", which is invalid.
samples/seccomp/ only contains host programs, so having it tristate
is pointless.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
A minor code cleanup.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Handle samples/ like the other top-level directories to simplify
the Makefile.
Include include/config/auto.conf earlier to evaluate
drivers-$(CONFIG_SAMPLES).
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Integrate iw_cm_verbs data members into ib_device_ops and ib_device
structs, this is done to achieve the following:
1) Avoid memory related bugs durring error unwind
2) Make the code more cleaner
3) Reduce code duplication
Signed-off-by: Kamal Heib <kamalheib1@gmail.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Add compatible string for the Qualcomm WCN3998 Bluetooth controller
Signed-off-by: Harish Bandi <c-hbandi@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Added new compatible for WCN3998 and corresponding voltage
and current values to WCN3998 compatible.
Changed driver code to support WCN3998
Signed-off-by: Harish Bandi <c-hbandi@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The driver interface cannot manipulate the sysfs of the compat device,
only of the full device so we must avoid calling the driver sysfs APIs on
compat devices.
This prevents an oops:
Call Trace:
dump_stack+0x5a/0x73
kobject_init+0x74/0x80
kobject_init_and_add+0x35/0xb0
hfi1_create_port_files+0x6e/0x3c0 [hfi1]
ib_setup_port_attrs+0x43b/0x560 [ib_core]
add_one_compat_dev+0x16a/0x230 [ib_core]
rdma_dev_init_net+0x110/0x160 [ib_core]
ops_init+0x38/0xf0
setup_net+0xcf/0x1e0
copy_net_ns+0xb7/0x130
create_new_namespaces+0x11a/0x1b0
unshare_nsproxy_namespaces+0x55/0xa0
ksys_unshare+0x1a7/0x340
__x64_sys_unshare+0xe/0x20
do_syscall_64+0x5b/0x180
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fixes: 5417783eabb2 ("RDMA/core: Support core port attributes in non init_net")
Reported-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Tested-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
There are two problems with WARN_ON() here. One: It is not ratelimited.
Two: We don't see which adapter was used when trying to transfer
something when already suspended. Implement a custom ratelimit once per
adapter and use dev_WARN there. This fixes both issues. Drawback is that
we don't see if multiple drivers are trying to transfer with the same
adapter while suspended. They need to be discovered one after the other
now. This is better than a high CPU load because a really broken driver
might try to resend endlessly.
Fixes: 9ac6cb5fbb17 ("i2c: add suspended flag and accessors for i2c adapters")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@vger.kernel.org # v5.1+
|
|
i2c/for-5.2
Mainly some pca954x work, i.e. removal of unused platform data support
and added support for sysfs interface for manipulating/examining the
idle state. And then a mechanical cocci-style patch.
|
|
real_qp should be initialized before ib_destroy_qp() is called.
ib_destroy_qp() may be called in the error flow if ib_create_qp_security()
failed.
Signed-off-by: Artemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
The QP transition optional parameters for the various transition for XRC
QPs are identical to those for RC QPs.
Many of the XRC QP transition optional parameter bits are missing from the
QP optional mask table. These omissions caused failures when doing XRC QP
state transitions.
For example, when trying to change the response timer of an XRC receive QP
via the RTS2RTS transition, the new timer value was ignored because
MLX5_QP_OPTPAR_RNR_TIMEOUT bit was missing from the optional params mask
for XRC qps for the RTS2RTS transition.
Fix this by adding the missing XRC optional parameters for all QP
transitions to the opt_mask table.
Fixes: e126ba97dba9 ("mlx5: Add driver for Mellanox Connect-IB adapters")
Fixes: a4774e9095de ("IB/mlx5: Fix opt param mask according to firmware spec")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
ib_uverbs_get_context does not have a uobject so it does not call the
rdma_lookup_get_uobject which is used to set up the uverbs_attr_bundle
ucontext. For ib_uverbs_get_context we need to set up this manually before
we send the uverbs_attr_bundle down to the driver layer.
This completes the change that was done in commit 70f06b26f07e ("IB:
ucontext should be set properly for all cmd & ioctl paths")
Signed-off-by: Shamir Rabinovitch <shamir.rabinovitch@oracle.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into i2c/for-5.2
at24: updates for linux v5.2
- change my e-mail address
- add a new compatible for Renesas R1EX24016 to the DT binding document
|
|
As we keep migrating documents to ReST, we're starting to see
more of such tags.
Right now, all such tags are pointing to a documentation file,
but regressions may be introduced.
So, add a check for such kind of issues as well.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
If one tries to run this script under linux-next, it would
hit lots of false-positives, due to the tree merges that
are stored under the Next/ directory.
So, add a logic to ignore it.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
Make it clear in the directory name that these are not intended for new
code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
Just like the CDDL the Apache license and the MPL must only be used as
a choice in additional to an GPL2 compatible license. Copy over the
boilerplate from the CDDL file to the other two after fixing it up to
make it clear the licenses need to be GPL2 compatible, not just the
more generic GPL compatible. For example the Apache 2 license is GPL3
compatible, but that doesn't matter for the kernel.
Also move these licenses to a separate directory and document the rules
in license-rules.rst.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
We never had a file called LICENSES/other/ZLib in the tree, so don't
reference it. Instead mention the GPL v1 as an (bad) example.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
Add missing license for Makefile
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This has no effect yet because CPU0 will always be a housekeeping CPU
until a later change.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J . Wysocki <rafael.j.wysocki@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linuxppc-dev@lists.ozlabs.org
Link: https://lkml.kernel.org/r/20190411033448.20842-2-npiggin@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Now that all AUX allocations are high-order by default, the software
double buffering PMU capability doesn't make sense any more, get rid
of it. In case some PMUs choose to opt out, we can re-introduce it.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: adrian.hunter@intel.com
Link: http://lkml.kernel.org/r/20190503085536.24119-3-alexander.shishkin@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
This recent commit:
5768402fd9c6e87 ("perf/ring_buffer: Use high order allocations for AUX buffers optimistically")
overlooked the fact that the previous one page granularity of the AUX buffer
provided an implicit double buffering capability to the PMU driver, which
went away when the entire buffer became one high-order page.
Always make the full-trace mode AUX allocation at least two-part to preserve
the previous behavior and allow the implicit double buffering to continue.
Reported-by: Ammy Yi <ammy.yi@intel.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: adrian.hunter@intel.com
Fixes: 5768402fd9c6e87 ("perf/ring_buffer: Use high order allocations for AUX buffers optimistically")
Link: http://lkml.kernel.org/r/20190503085536.24119-2-alexander.shishkin@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/will/linux into for-next/core
|
