| Age | Commit message (Collapse) | Author |
|---|
|
The csel_reg and csel_mask fields in struct regulator_desc needs to
be generic for drivers. Not just for TPS65218.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
|
|
Switch from .set_mmss to .set_time as the former is deprecated.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Call the 64bit versions of rtc_time_to_tm now that the range is enforced by
the core.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The TX4939 RTC is a 48bit counter that counts two on every clock edge of
32.768 KHz oscillator clock so it counts 32bit seconds.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The tested condition will never happen as the core always passes a fully
set struct tm (using rtc_ktime_to_tm) to the .set_alarm callback.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Harini Katakam says:
====================
Macb power management support for ZynqMP
This series adds support for macb suspend/resume with system power down.
In relation to the above, this series also updates mdio_read/write
function for PM and adds tsu clock management.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When macb device is suspended and system is powered down, the clocks
are removed and hence macb should be closed gracefully and restored
upon resume. This patch does the same by switching off the net device,
suspending phy and performing necessary cleanup of interrupts and BDs.
Upon resume, all these are reinitialized again.
Reset of macb device is done only when GEM is not a wake device.
Even when gem is a wake device, tx queues can be stopped and ptp device
can be closed (tsu clock will be disabled in pm_runtime_suspend) as
wake event detection has no dependency on this.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add runtime pm functions and move clock handling there.
Add runtime PM calls to mdio functions to allow for active mdio bus.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TSU clock needs to be enabled/disabled as per support in devicetree
and it should also be controlled during suspend/resume (WOL has no
dependency on this clock).
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace the while loop in MDIO read/write functions with a timeout.
In addition, add a check for MDIO bus busy before initiating a new
operation as well to make sure there is no ongoing MDIO operation.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Tristram Ha says:
====================
net: dsa: microchip: add KSZ9893 switch support
This series of patches is to modify the KSZ9477 DSA driver to support
running KSZ9893 switch.
The KSZ9893 switch is similar to KSZ9477 except the ingress tail tag has
1 byte instead of 2 bytes. The XMII register that governs the MAC
communication also has different register definitions.
v1
- Put KSZ9893 tagging in separate patch
- Remove other switch support
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add KSZ9893 switch support in KSZ9477 driver. This switch is similar to
KSZ9477 except the ingress tail tag has 1 byte instead of 2 bytes, so
KSZ9893 tagging will be used.
The XMII register that governs how the host port communicates with the
MAC also has different register definitions.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
KSZ9893 switch is similar to KSZ9477 switch except the ingress tail tag
has 1 byte instead of 2 bytes. The size of the portmap is smaller and
so the override and lookup bits are also moved.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Document additional Microchip KSZ9477 family switches.
Show how KSZ8565 switch should be configured as the host port is port 7
instead of port 5.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Let the core handle the RTC range instead of open coding it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The IRQ is requested before the struct rtc is allocated and registered, but
this struct is used in the IRQ handler. This may lead to a NULL pointer
dereference.
Switch to devm_rtc_allocate_device/rtc_register_device to allocate the rtc
struct before requesting the IRQ.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The imx-sc driver properly sets range_max, use rtc_time64_to_tm() instead
of the deprecated rtc_time_to_tm()
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Yue Haibing says:
====================
appletalk: small cleanup and bugfix
v2:
- Add cover letter log
This patch series mainly fix a use-after-free bug in atalk_proc_exit.
patch 1 use remove_proc_subtree helper to simplify atalk_proc fs code,
also some other cleanup.
patch 2 add proper error cleanup path in atalk_init to fix the issue, which
based on the patch 1 because of the change of atalk_proc_exit context.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
KASAN report this:
BUG: KASAN: use-after-free in pde_subdir_find+0x12d/0x150 fs/proc/generic.c:71
Read of size 8 at addr ffff8881f41fe5b0 by task syz-executor.0/2806
CPU: 0 PID: 2806 Comm: syz-executor.0 Not tainted 5.0.0-rc7+ #45
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0xfa/0x1ce lib/dump_stack.c:113
print_address_description+0x65/0x270 mm/kasan/report.c:187
kasan_report+0x149/0x18d mm/kasan/report.c:317
pde_subdir_find+0x12d/0x150 fs/proc/generic.c:71
remove_proc_entry+0xe8/0x420 fs/proc/generic.c:667
atalk_proc_exit+0x18/0x820 [appletalk]
atalk_exit+0xf/0x5a [appletalk]
__do_sys_delete_module kernel/module.c:1018 [inline]
__se_sys_delete_module kernel/module.c:961 [inline]
__x64_sys_delete_module+0x3dc/0x5e0 kernel/module.c:961
do_syscall_64+0x147/0x600 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x462e99
Code: f7 d8 64 89 02 b8 ff ff ff ff c3 66 0f 1f 44 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 bc ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007fb2de6b9c58 EFLAGS: 00000246 ORIG_RAX: 00000000000000b0
RAX: ffffffffffffffda RBX: 000000000073bf00 RCX: 0000000000462e99
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 00000000200001c0
RBP: 0000000000000002 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00007fb2de6ba6bc
R13: 00000000004bccaa R14: 00000000006f6bc8 R15: 00000000ffffffff
Allocated by task 2806:
set_track mm/kasan/common.c:85 [inline]
__kasan_kmalloc.constprop.3+0xa0/0xd0 mm/kasan/common.c:496
slab_post_alloc_hook mm/slab.h:444 [inline]
slab_alloc_node mm/slub.c:2739 [inline]
slab_alloc mm/slub.c:2747 [inline]
kmem_cache_alloc+0xcf/0x250 mm/slub.c:2752
kmem_cache_zalloc include/linux/slab.h:730 [inline]
__proc_create+0x30f/0xa20 fs/proc/generic.c:408
proc_mkdir_data+0x47/0x190 fs/proc/generic.c:469
0xffffffffc10c01bb
0xffffffffc10c0166
do_one_initcall+0xfa/0x5ca init/main.c:887
do_init_module+0x204/0x5f6 kernel/module.c:3460
load_module+0x66b2/0x8570 kernel/module.c:3808
__do_sys_finit_module+0x238/0x2a0 kernel/module.c:3902
do_syscall_64+0x147/0x600 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Freed by task 2806:
set_track mm/kasan/common.c:85 [inline]
__kasan_slab_free+0x130/0x180 mm/kasan/common.c:458
slab_free_hook mm/slub.c:1409 [inline]
slab_free_freelist_hook mm/slub.c:1436 [inline]
slab_free mm/slub.c:2986 [inline]
kmem_cache_free+0xa6/0x2a0 mm/slub.c:3002
pde_put+0x6e/0x80 fs/proc/generic.c:647
remove_proc_entry+0x1d3/0x420 fs/proc/generic.c:684
0xffffffffc10c031c
0xffffffffc10c0166
do_one_initcall+0xfa/0x5ca init/main.c:887
do_init_module+0x204/0x5f6 kernel/module.c:3460
load_module+0x66b2/0x8570 kernel/module.c:3808
__do_sys_finit_module+0x238/0x2a0 kernel/module.c:3902
do_syscall_64+0x147/0x600 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
The buggy address belongs to the object at ffff8881f41fe500
which belongs to the cache proc_dir_entry of size 256
The buggy address is located 176 bytes inside of
256-byte region [ffff8881f41fe500, ffff8881f41fe600)
The buggy address belongs to the page:
page:ffffea0007d07f80 count:1 mapcount:0 mapping:ffff8881f6e69a00 index:0x0
flags: 0x2fffc0000000200(slab)
raw: 02fffc0000000200 dead000000000100 dead000000000200 ffff8881f6e69a00
raw: 0000000000000000 00000000800c000c 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff8881f41fe480: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
ffff8881f41fe500: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
>ffff8881f41fe580: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
ffff8881f41fe600: fc fc fc fc fc fc fc fc fb fb fb fb fb fb fb fb
ffff8881f41fe680: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
It should check the return value of atalk_proc_init fails,
otherwise atalk_exit will trgger use-after-free in pde_subdir_find
while unload the module.This patch fix error cleanup path of atalk_init
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use remove_proc_subtree to remove the whole subtree
on cleanup.Also do some cleanup.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When Ocelot phy-mode is QSGMII, all 4 ports involved in
QSGMII shall be kept out of reset and
Tx lanes shall be enabled to pass the data.
Fixes: a556c76adc05 ("net: mscc: Add initial Ocelot switch support")
Signed-off-by: Kavya Sree Kotagiri <kavyasree.kotagiri@microchip.com>
Signed-off-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Co-developed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Clear the on-stack STACK_FRAME_REGS_MARKER on exception exit in order
to avoid confusing stacktrace like the one below.
Call Trace:
[c0e9dca0] [c01c42a0] print_address_description+0x64/0x2bc (unreliable)
[c0e9dcd0] [c01c4684] kasan_report+0xfc/0x180
[c0e9dd10] [c0895130] memchr+0x24/0x74
[c0e9dd30] [c00a9e38] msg_print_text+0x124/0x574
[c0e9dde0] [c00ab710] console_unlock+0x114/0x4f8
[c0e9de40] [c00adc60] vprintk_emit+0x188/0x1c4
--- interrupt: c0e9df00 at 0x400f330
LR = init_stack+0x1f00/0x2000
[c0e9de80] [c00ae3c4] printk+0xa8/0xcc (unreliable)
[c0e9df20] [c0c27e44] early_irq_init+0x38/0x108
[c0e9df50] [c0c15434] start_kernel+0x310/0x488
[c0e9dff0] [00003484] 0x3484
With this patch the trace becomes:
Call Trace:
[c0e9dca0] [c01c42c0] print_address_description+0x64/0x2bc (unreliable)
[c0e9dcd0] [c01c46a4] kasan_report+0xfc/0x180
[c0e9dd10] [c0895150] memchr+0x24/0x74
[c0e9dd30] [c00a9e58] msg_print_text+0x124/0x574
[c0e9dde0] [c00ab730] console_unlock+0x114/0x4f8
[c0e9de40] [c00adc80] vprintk_emit+0x188/0x1c4
[c0e9de80] [c00ae3e4] printk+0xa8/0xcc
[c0e9df20] [c0c27e44] early_irq_init+0x38/0x108
[c0e9df50] [c0c15434] start_kernel+0x310/0x488
[c0e9dff0] [00003484] 0x3484
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Remove license boilerplate text.
Signed-off-by: Jules Irenge <jbi.octave@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add SPDX GPL-2.0+ license to fix missing SPDX warning
reported by checkpatch.pl.
Signed-off-by: Jules Irenge <jbi.octave@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"One more set of simple ARM platform fixes:
- A boot regression on qualcomm msm8998
- Gemini display controllers got turned off by accident
- incorrect reference counting in optee"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
tee: optee: add missing of_node_put after of_device_is_available
arm64: dts: qcom: msm8998: Extend TZ reserved memory area
ARM: dts: gemini: Re-enable display controller
|
|
In the series fc8b81a5981f ("Merge branch 'lockless-qdisc-series'")
John made the assumption that the data path had no need to read
the qdisc qlen (number of packets in the qdisc).
It is true when pfifo_fast is used as the root qdisc, or as direct MQ/MQPRIO
children.
But pfifo_fast can be used as leaf in class full qdiscs, and existing
logic needs to access the child qlen in an efficient way.
HTB breaks badly, since it uses cl->leaf.q->q.qlen in :
htb_activate() -> WARN_ON()
htb_dequeue_tree() to decide if a class can be htb_deactivated
when it has no more packets.
HFSC, DRR, CBQ, QFQ have similar issues, and some calls to
qdisc_tree_reduce_backlog() also read q.qlen directly.
Using qdisc_qlen_sum() (which iterates over all possible cpus)
in the data path is a non starter.
It seems we have to put back qlen in a central location,
at least for stable kernels.
For all qdisc but pfifo_fast, qlen is guarded by the qdisc lock,
so the existing q.qlen{++|--} are correct.
For 'lockless' qdisc (pfifo_fast so far), we need to use atomic_{inc|dec}()
because the spinlock might be not held (for example from
pfifo_fast_enqueue() and pfifo_fast_dequeue())
This patch adds atomic_qlen (in the same location than qlen)
and renames the following helpers, since we want to express
they can be used without qdisc lock, and that qlen is no longer percpu.
- qdisc_qstats_cpu_qlen_dec -> qdisc_qstats_atomic_qlen_dec()
- qdisc_qstats_cpu_qlen_inc -> qdisc_qstats_atomic_qlen_inc()
Later (net-next) we might revert this patch by tracking all these
qlen uses and replace them by a more efficient method (not having
to access a precise qlen, but an empty/non_empty status that might
be less expensive to maintain/track).
Another possibility is to have a legacy pfifo_fast version that would
be used when used a a child qdisc, since the parent qdisc needs
a spinlock anyway. But then, future lockless qdiscs would also
have the same problem.
Fixes: 7e66016f2c65 ("net: sched: helpers to sum qlen and qlen for per cpu logic")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2019-03-01
This series adds multipath offload support and contains some small updates
to mlx5 driver.
Multipath offload support from Roi Dayan:
We are going to track SW multipath route and related nexthops and reflect
that as port affinity to the HW.
1) Some patches are preparation.
2) add the multipath mode and fib events handling.
3) add support to handle offload failure for net error, i.e.
port down.
4) Small updates to match the behavior of multipath
Two small updates from Eran Ben Elisha,
5) Make a function static
6) Update PCIe supported devices list.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter/IPVS updates for net-next:
1) Add .release_ops to properly unroll .select_ops, use it from nft_compat.
After this change, we can remove list of extensions too to simplify this
codebase.
2) Update amanda conntrack helper to support v3.4, from Florian Tham.
3) Get rid of the obsolete BUGPRINT macro in ebtables, from
Florian Westphal.
4) Merge IPv4 and IPv6 masquerading infrastructure into one single module.
From Florian Westphal.
5) Patchset to remove nf_nat_l3proto structure to get rid of
indirections, from Florian Westphal.
6) Skip unnecessary conntrack timeout updates in case the value is
still the same, also from Florian Westphal.
7) Remove unnecessary 'fall through' comments in empty switch cases,
from Li RongQing.
8) Fix lookup to fixed size hashtable sets on big endian with 32-bit keys.
9) Incorrect logic to deactivate path of fixed size hashtable sets,
element was being tested to self.
10) Remove nft_hash_key(), the bitmap set is always selected for 16-bit
keys.
11) Use boolean whenever possible in IPVS codebase, from Andrea Claudi.
12) Enter close state in conntrack if RST matches exact sequence number,
from Florian Westphal.
13) Initialize dst_cache in tunnel extension, from wenxu.
14) Pass protocol as u16 to xt_check_match and xt_check_target, from
Li RongQing.
15) SCTP header is granted to be in a linear area from IPVS NAT handler,
from Xin Long.
16) Don't steal packets coming from slave VRF device from the
ip_sabotage_in() path, from David Ahern.
17) Fix unsafe update of basechain stats, from Li RongQing.
18) Make sure CONNTRACK_LOCKS is power of 2 to let compiler optimize
modulo operation as bitwise AND, from Li RongQing.
19) Use device_attribute instead of internal definition in the IDLETIMER
target, from Sami Tolvanen.
20) Merge redir, masq and IPv4/IPv6 NAT chain types, from Florian Westphal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
Johan Hedberg says:
====================
pull request: bluetooth-next 2019-03-02
Here's one more bluetooth-next pull request for the 5.1 kernel:
- Added support for MediaTek MT7663U and MT7668U UART devices
- Cleanups & fixes to the hci_qca driver
- Fixed wakeup pin behavior for QCA6174A controller
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for Epson rx8571 real-time clock. rx8571 rtc is compatible
with rx8581,except that rx8571 has additional 16 bytes of RAM.
16 bytes of nvmem is supported and exposed in sysfs (# is the instance
number,starting with 0): /sys/bus/nvmem/devices/rx8571-#/nvmem
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The Epson rx8571 is compatible with the Epson rx8581 RTC.
The difference between the rx8571 and rx8581 RTC is that the former has
16 bytes more RAM. This renders them incompatible from a DT point of view.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Some of defines are not in use since
7b5768486a910532885f01b9d2dad4818c8b3be1. Remove it to make the code
easier to read and understand.
Signed-off-by: Alexey Roslyakov <alexey.roslyakov@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"Two last minute fixes:
- Prevent value evaluation via functions happening in the user access
enabled region of __put_user() (put another way: make sure to
evaluate the value to be stored in user space _before_ enabling
user space accesses)
- Correct the definition of a Hyper-V hypercall constant"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/hyper-v: Fix definition of HV_MAX_FLUSH_REP_COUNT
x86/uaccess: Don't leak the AC flag into __put_user() value evaluation
|
|
When the current bvec can be merged to the 1st segment, the bio's front
segment size has to be updated.
However, dcebd755926b doesn't consider that case, then bio's front
segment size may not be correct.
This patch fixes this issue.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Omar Sandoval <osandov@fb.com>
Fixes: dcebd755926b ("block: use bio_for_each_bvec() to compute multi-page bvec count")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Nine small fixes.
The resume fix is a cosmetic removal of a warning with an incorrect
condition causing it to alarm people wrongly.
The other eight patches correct a thinko in Christoph Hellwig's DMA
conversion series. Without it all these drivers end up with 32 bit DMA
masks meaning they bounce any page over 4GB before sending it to the
controller.
Nowadays, even laptops mostly have memory above 4GB, so this can lead
to significant performance degradation with all the bouncing"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: core: Avoid that system resume triggers a kernel warning
scsi: hptiop: fix calls to dma_set_mask()
scsi: hisi_sas: fix calls to dma_set_mask_and_coherent()
scsi: csiostor: fix calls to dma_set_mask_and_coherent()
scsi: bfa: fix calls to dma_set_mask_and_coherent()
scsi: aic94xx: fix calls to dma_set_mask_and_coherent()
scsi: 3w-sas: fix calls to dma_set_mask_and_coherent()
scsi: 3w-9xxx: fix calls to dma_set_mask_and_coherent()
scsi: lpfc: fix calls to dma_set_mask_and_coherent()
|
|
Stanislav Fomichev says:
====================
Recently we had linux-next bpf/bpf-next conflict when we added new
functionality to the test_progs.c at the same location. Let's split
test_progs.c the same way we recently split test_verifier.c.
I follow the same patten we did in commit 2dfb40121ee8 ("selftests: bpf:
prepare for break up of verifier tests") for verifier: create
scaffolding to support dedicated files and slowly move the tests into
separate files.
The first patch adds scaffolding, subsequent patches move progs into
separate files.
In theory, many of the standalone tests can be migrated to this new
framework as well. They get the benefit of common CHECK macro and
bpf_find_map function which a lot of standalone tests need to redefine.
v3 changes:
* respin on top of commit ebace0e981b2 ("selftests/bpf: use
__bpf_constant_htons in test_prog.c for flow dissector")
* put bpf_rlimit.h into test_progs.c instead of test_progs.h
v2 changes:
* added cover letter, added more description about file structure
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Move the rest of prog tests into separate files.
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Move spinlock prog tests into separate files.
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Move tracepoint prog tests into separate files.
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Move stackmap prog tests into separate files.
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Move xdp prog tests into separate files.
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Move pkt access prog tests into separate files.
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Add new prog_tests directory where tests are supposed to land.
Each prog_tests/<filename>.c is expected to have a global function
with signature 'void test_<filename>(void)'. Makefile automatically
generates prog_tests/tests.h file with entry for each prog_tests file:
#ifdef DECLARE
extern void test_<filename>(void);
...
#endif
#ifdef CALL
test_<filename>();
...
#endif
prog_tests/tests.h is included in test_progs.c in two places with
appropriate defines. This scheme allows us to move each function with
a separate patch without breaking anything.
Compared to the recent verifier split, each separate file here is
a compilation unit and test_progs.[ch] is now used as a place to put
some common routines that might be used by multiple tests.
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
This adds the support of enabling MT7663U and MT7668U Bluetooth function
running on the top of btmtkuart driver.
There are a few differences between MT766[3,8]U and MT7622 where
MT766[3,8]U are standalone devices based on UART transport while MT7622
bluetooth is a built-in device on MediaTek SoC communicating with the host
through BTIF serial transport. Thus, extra setup sequence is necessary
for these standalone devices such as remote regulator and reset control via
GPIO, baud rate changing handshake between the host and device and so on.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Lawrence Brakmo says:
====================
Host Bandwidth Manager is a framework for limiting the bandwidth used
by v2 cgroups. It consists of 1 BPF helper, a sample BPF program to
limit egress bandwdith as well as a sample user program and script to
simplify HBM testing.
The sample HBM BPF program is not meant to be production quality, it is
provided as proof of concept. A lot more information, including sample
runs in some cases, are provided in the commit messages of the individual
patches.
A future patch will add support for reducing TCP's cwnd (we are evaluating
alternatives). Another patch will add support for fair queueing's Earliest
Departure Time. Until then, HBM is better suited for flows supporitng ECN.
In addition, A BPF program to limit ingress bandwidth will be provided in
an upcomming patchset.
Changes from v1 to v2:
* bpf_tcp_enter_cwr can only be called from a cgroup skb egress BPF
program (otherwise load or attach will fail) where we already hold
the sk lock. Also only applies for ESTABLISHED state.
* bpf_skb_ecn_set_ce uses INET_ECN_set_ce()
* bpf_tcp_check_probe_timer now uses tcp_reset_xmit_timer. Can only be
used by egress cgroup skb programs.
* removed load_cg_skb user program.
* nrm bpf egress program checks packet header in skb to determine
ECN value. Now also works for ECN enabled UDP packets.
Using ECN_ defines instead of integers.
* NRM script test program now uses bpftool instead of load_cg_skb
Changes from v2 to v3:
* Changed name from NRM (Network Resource Manager) to HBM (Host
Bandwdith Manager)
* The bpf helper to set ECN ce now checks that the header is writeable
* Removed helper bpf functions that modified TCP state due to a concern
about whether the socket is locked by the current thread.
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Script for testing HBM (Host Bandwidth Manager) framework.
It creates a cgroup to use for testing and load a BPF program to limit
egress bandwidht. It then uses iperf3 or netperf to create
loads. The output is the goodput in Mbps (unless -D is used).
It can work on a single host using loopback or among two hosts (with netperf).
When using loopback, it is recommended to also introduce a delay of at least
1ms (-d=1), otherwise the assigned bandwidth is likely to be underutilized.
USAGE: $name [out] [-b=<prog>|--bpf=<prog>] [-c=<cc>|--cc=<cc>] [-D]
[-d=<delay>|--delay=<delay>] [--debug] [-E]
[-f=<#flows>|--flows=<#flows>] [-h] [-i=<id>|--id=<id >] [-l]
[-N] [-p=<port>|--port=<port>] [-P] [-q=<qdisc>]
[-R] [-s=<server>|--server=<server] [--stats]
[-t=<time>|--time=<time>] [-w] [cubic|dctcp]
Where:
out Egress (default egress)
-b or --bpf BPF program filename to load and attach.
Default is nrm_out_kern.o for egress,
-c or -cc TCP congestion control (cubic or dctcp)
-d or --delay Add a delay in ms using netem
-D In addition to the goodput in Mbps, it also outputs
other detailed information. This information is
test dependent (i.e. iperf3 or netperf).
--debug Print BPF trace buffer
-E Enable ECN (not required for dctcp)
-f or --flows Number of concurrent flows (default=1)
-i or --id cgroup id (an integer, default is 1)
-l Do not limit flows using loopback
-N Use netperf instead of iperf3
-h Help
-p or --port iperf3 port (default is 5201)
-P Use an iperf3 instance for each flow
-q Use the specified qdisc.
-r or --rate Rate in Mbps (default 1s 1Gbps)
-R Use TCP_RR for netperf. 1st flow has req
size of 10KB, rest of 1MB. Reply in all
cases is 1 byte.
More detailed output for each flow can be found
in the files netperf.<cg>.<flow>, where <cg> is the
cgroup id as specified with the -i flag, and <flow>
is the flow id starting at 1 and increasing by 1 for
flow (as specified by -f).
-s or --server hostname of netperf server. Used to create netperf
test traffic between to hosts (default is within host)
netserver must be running on the host.
--stats Get HBM stats (marked, dropped, etc.)
-t or --time duration of iperf3 in seconds (default=5)
-w Work conserving flag. cgroup can increase its
bandwidth beyond the rate limit specified
while there is available bandwidth. Current
implementation assumes there is only one NIC
(eth0), but can be extended to support multiple
NICs. This is just a proof of concept.
cubic or dctcp specify TCP CC to use
Examples:
./do_hbm_test.sh -l -d=1 -D --stats
Runs a 5 second test, using a single iperf3 flow and with the default
rate limit of 1Gbps and a delay of 1ms (using netem) using the default
TCP congestion control on the loopback device (hence we use "-l" to
enforce bandwidth limit on loopback device). Since no direction is
specified, it defaults to egress. Since no TCP CC algorithm is
specified it uses the system default (Cubic for this test).
With no -D flag, only the value of the AGGREGATE OUTPUT would show.
id refers to the cgroup id and is useful when running multi cgroup
tests (supported by a future patch).
This patchset does not support calling TCP's congesion window
reduction, even when packets are dropped by the BPF program, resulting
in a large number of packets dropped. It is recommended that the current
HBM implemenation only be used with ECN enabled flows. A future patch
will add support for reducing TCP's cwnd and will increase the
performance of non-ECN enabled flows.
Output:
Details for HBM in cgroup 1
id:1
rate_mbps:493
duration:4.8 secs
packets:11355
bytes_MB:590
pkts_dropped:4497
bytes_dropped_MB:292
pkts_marked_percent: 39.60
bytes_marked_percent: 49.49
pkts_dropped_percent: 39.60
bytes_dropped_percent: 49.49
PING AVG DELAY:2.075
AGGREGATE_GOODPUT:505
./do_nrm_test.sh -l -d=1 -D --stats dctcp
Same as above but using dctcp. Note that fewer bytes are dropped
(0.01% vs. 49%).
Output:
Details for HBM in cgroup 1
id:1
rate_mbps:945
duration:4.9 secs
packets:16859
bytes_MB:578
pkts_dropped:1
bytes_dropped_MB:0
pkts_marked_percent: 28.74
bytes_marked_percent: 45.15
pkts_dropped_percent: 0.01
bytes_dropped_percent: 0.01
PING AVG DELAY:2.083
AGGREGATE_GOODPUT:965
./do_nrm_test.sh -d=1 -D --stats
As first example, but without limiting loopback device (i.e. no
"-l" flag). Since there is no bandwidth limiting, no details for
HBM are printed out.
Output:
Details for HBM in cgroup 1
PING AVG DELAY:2.019
AGGREGATE_GOODPUT:42655
./do_hbm.sh -l -d=1 -D --stats -f=2
Uses iper3 and does 2 flows
./do_hbm.sh -l -d=1 -D --stats -f=4 -P
Uses iperf3 and does 4 flows, each flow as a separate process.
./do_hbm.sh -l -d=1 -D --stats -f=4 -N
Uses netperf, 4 flows
./do_hbm.sh -f=1 -r=2000 -t=5 -N -D --stats dctcp -s=<server-name>
Uses netperf between two hosts. The remote host name is specified
with -s= and you need to start the program netserver manually on
the remote host. It will use 1 flow, a rate limit of 2Gbps and dctcp.
./do_hbm.sh -f=1 -r=2000 -t=5 -N -D --stats -w dctcp \
-s=<server-name>
As previous, but allows use of extra bandwidth. For this test the
rate is 8Gbps vs. 1Gbps of the previous test.
Signed-off-by: Lawrence Brakmo <brakmo@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
The program nrm creates a cgroup and attaches a BPF program to the
cgroup for testing HBM (Host Bandwidth Manager) for egress traffic.
One still needs to create network traffic. This can be done through
netesto, netperf or iperf3.
A follow-up patch contains a script to create traffic.
USAGE: hbm [-d] [-l] [-n <id>] [-r <rate>] [-s] [-t <secs>]
[-w] [-h] [prog]
Where:
-d Print BPF trace debug buffer
-l Also limit flows doing loopback
-n <#> To create cgroup "/hbm#" and attach prog. Default is /nrm1
This is convenient when testing HBM in more than 1 cgroup
-r <rate> Rate limit in Mbps
-s Get HBM stats (marked, dropped, etc.)
-t <time> Exit after specified seconds (deault is 0)
-w Work conserving flag. cgroup can increase its bandwidth
beyond the rate limit specified while there is available
bandwidth. Current implementation assumes there is only
NIC (eth0), but can be extended to support multiple NICs.
Currrently only supported for egress. Note, this is just
a proof of concept.
-h Print this info
prog BPF program file name. Name defaults to hbm_out_kern.o
More information about HBM can be found in the paper "BPF Host Resource
Management" presented at the 2018 Linux Plumbers Conference, Networking Track
(http://vger.kernel.org/lpc_net2018_talks/LPC%20BPF%20Network%20Resource%20Paper.pdf)
Signed-off-by: Lawrence Brakmo <brakmo@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
A cgroup skb BPF program to limit cgroup output bandwidth.
It uses a modified virtual token bucket queue to limit average
egress bandwidth. The implementation uses credits instead of tokens.
Negative credits imply that queueing would have happened (this is
a virtual queue, so no queueing is done by it. However, queueing may
occur at the actual qdisc (which is not used for rate limiting).
This implementation uses 3 thresholds, one to start marking packets and
the other two to drop packets:
CREDIT
- <--------------------------|------------------------> +
| | | 0
| Large pkt |
| drop thresh |
Small pkt drop Mark threshold
thresh
The effect of marking depends on the type of packet:
a) If the packet is ECN enabled, then the packet is ECN ce marked.
The current mark threshold is tuned for DCTCP.
c) Else, it is dropped if it is a large packet.
If the credit is below the drop threshold, the packet is dropped.
Note that dropping a packet through the BPF program does not trigger CWR
(Congestion Window Reduction) in TCP packets. A future patch will add
support for triggering CWR.
This BPF program actually uses 2 drop thresholds, one threshold
for larger packets (>= 120 bytes) and another for smaller packets. This
protects smaller packets such as SYNs, ACKs, etc.
The default bandwidth limit is set at 1Gbps but this can be changed by
a user program through a shared BPF map. In addition, by default this BPF
program does not limit connections using loopback. This behavior can be
overwritten by the user program. There is also an option to calculate
some statistics, such as percent of packets marked or dropped, which
the user program can access.
A latter patch provides such a program (hbm.c)
Signed-off-by: Lawrence Brakmo <brakmo@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
