| Age | Commit message (Collapse) | Author |
|---|
|
num_pipes is used for mutex created in mtk_drm_crtc_create(). If we
don't clear num_pipes count, when rebinding driver, the count will
be accumulated. From mtk_disp_mutex_get(), there can only be at most
10 mutex id. Clear this number so it starts from 0 in every rebind.
Fixes: 119f5173628a ("drm/mediatek: Add DRM Driver for Mediatek SoC MT8173.")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: CK Hu <ck.hu@mediatek.com>
|
|
shutdown all CRTC when unbinding drm driver.
Fixes: 119f5173628a ("drm/mediatek: Add DRM Driver for Mediatek SoC MT8173.")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: CK Hu <ck.hu@mediatek.com>
|
|
Unbinding components (i.e. mtk_dsi and mtk_disp_ovl/rdma/color) will
trigger master(mtk_drm)'s .unbind(), and currently mtk_drm's unbind
won't actually unbind components. During the next bind,
mtk_drm_kms_init() is called, and the components are added back.
.unbind() should call mtk_drm_kms_deinit() to unbind components.
And since component_master_del() in .remove() will trigger .unbind(),
which will also unregister device, it's fine to remove original functions
called here.
Fixes: 119f5173628a ("drm/mediatek: Add DRM Driver for Mediatek SoC MT8173.")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: CK Hu <ck.hu@mediatek.com>
|
|
detatch panel in mtk_dsi_destroy_conn_enc(), since .bind will try to
attach it again.
Fixes: 2e54c14e310f ("drm/mediatek: Add DSI sub driver")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: CK Hu <ck.hu@mediatek.com>
|
|
Some SFP modules do not like reads longer than 16 bytes, so read the
EEPROM in chunks of 16 bytes at a time. This behaviour is not specified
in the SFP MSAs, which specifies:
"The serial interface uses the 2-wire serial CMOS E2PROM protocol
defined for the ATMEL AT24C01A/02/04 family of components."
and
"As long as the SFP+ receives an acknowledge, it shall serially clock
out sequential data words. The sequence is terminated when the host
responds with a NACK and a STOP instead of an acknowledge."
We must avoid breaking a read across a 16-bit quantity in the diagnostic
page, thankfully all 16-bit quantities in that page are naturally
aligned.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sysctl setting bc_forwarding for $rp2 is needed when ping_test_from h2,
otherwise the bc packets from $rp2 won't be forwarded. This patch is to
add this setting for $rp2.
Also, as ping_test_from does grep "$from" only, which could match some
unexpected output, some test case doesn't really work, like:
# ping_test_from $h2 198.51.200.255 198.51.200.2
PING 198.51.200.255 from 198.51.100.2 veth3: 56(84) bytes of data.
64 bytes from 198.51.100.1: icmp_seq=1 ttl=64 time=0.336 ms
When doing grep $form (198.51.200.2), the output could still match.
So change to grep "bytes from $from" instead.
Fixes: 40f98b9af943 ("selftests: add a selftest for directed broadcast forwarding")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
enabled
Should only enable HW RX_2BYTE_OFFSET function in the case NET_IP_ALIGN
equals to 2.
Signed-off-by: Mark Lee <mark-mc.lee@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Should hw_feature as hardware capability flags to check if hardware LRO
got support.
Signed-off-by: Mark Lee <mark-mc.lee@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC fixes from Vineet Gupta:
- Fix for userspace trying to access kernel vaddr space
- HSDK platform DT updates
- Cleanup some build warnings
* tag 'arc-5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: [plat-hsdk] Get rid of inappropriate PHY settings
ARC: [plat-hsdk]: Add support of Vivante GPU
ARC: [plat-hsdk]: enable creg-gpio controller
ARC: [plat-hsdk]: Add missing FIFO size entry in GMAC node
ARC: [plat-hsdk]: Add missing multicast filter bins number to GMAC node
ARC: mm: SIGSEGV userspace trying to access kernel virtual memory
ARC: fix build warnings
|
|
Fix ability to set RX descriptor number, the reason - initially
"tx_max_pending" was set incorrectly, but the issue appears after
adding sanity check, so fix is for "sanity" patch.
Fixes: 37e2d99b59c476 ("ethtool: Ensure new ring parameters are within bounds during SRINGPARAM")
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Martin Lau says:
====================
s series has fixes when running reuseport's bpf_prog for udp lookup.
If there is reuseport's bpf_prog, the common issue is the reuseport code
path expects skb->data pointing to the transport header (udphdr here).
A couple of commits broke this expectation. The issue is specific
to running bpf_prog, so bpf tag is used for this series.
Please refer to the individual commit message for details.
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
When the commit a6024562ffd7 ("udp: Add GRO functions to UDP socket")
added udp[46]_lib_lookup_skb to the udp_gro code path, it broke
the reuseport_select_sock() assumption that skb->data is pointing
to the transport header.
This patch follows an earlier __udp6_lib_err() fix by
passing a NULL skb to avoid calling the reuseport's bpf_prog.
Fixes: a6024562ffd7 ("udp: Add GRO functions to UDP socket")
Cc: Tom Herbert <tom@herbertland.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
__udp6_lib_err() may be called when handling icmpv6 message. For example,
the icmpv6 toobig(type=2). __udp6_lib_lookup() is then called
which may call reuseport_select_sock(). reuseport_select_sock() will
call into a bpf_prog (if there is one).
reuseport_select_sock() is expecting the skb->data pointing to the
transport header (udphdr in this case). For example, run_bpf_filter()
is pulling the transport header.
However, in the __udp6_lib_err() path, the skb->data is pointing to the
ipv6hdr instead of the udphdr.
One option is to pull and push the ipv6hdr in __udp6_lib_err().
Instead of doing this, this patch follows how the original
commit 538950a1b752 ("soreuseport: setsockopt SO_ATTACH_REUSEPORT_[CE]BPF")
was done in IPv4, which has passed a NULL skb pointer to
reuseport_select_sock().
Fixes: 538950a1b752 ("soreuseport: setsockopt SO_ATTACH_REUSEPORT_[CE]BPF")
Cc: Craig Gallek <kraig@google.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Song Liu <songliubraving@fb.com>
Acked-by: Craig Gallek <kraig@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Herbert Xu pointed out that commit bb73c52bad36 ("rcu: Don't disable
preemption for Tiny and Tree RCU readers") was incorrect in making the
preempt_disable/enable() be conditional on CONFIG_PREEMPT_COUNT.
If CONFIG_PREEMPT_COUNT isn't enabled, the preemption enable/disable is
a no-op, but still is a compiler barrier.
And RCU locking still _needs_ that compiler barrier.
It is simply fundamentally not true that RCU locking would be a complete
no-op: we still need to guarantee (for example) that things that can
trap and cause preemption cannot migrate into the RCU locked region.
The way we do that is by making it a barrier.
See for example commit 386afc91144b ("spinlocks and preemption points
need to be at least compiler barriers") from back in 2013 that had
similar issues with spinlocks that become no-ops on UP: they must still
constrain the compiler from moving other operations into the critical
region.
Now, it is true that a lot of RCU operations already use READ_ONCE() and
WRITE_ONCE() (which in practice likely would never be re-ordered wrt
anything remotely interesting), but it is also true that that is not
globally the case, and that it's not even necessarily always possible
(ie bitfields etc).
Reported-by: Herbert Xu <herbert@gondor.apana.org.au>
Fixes: bb73c52bad36 ("rcu: Don't disable preemption for Tiny and Tree RCU readers")
Cc: stable@kernel.org
Cc: Boqun Feng <boqun.feng@gmail.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add a couple of new debugfs entries "ipc_flood_count"
and "ipc_flood_duration_ms" that can be used to
execute the IPC flood test. "ipc_flood_count" floods the DSP
with the number of test IPCs specified and ipc_flood_duration_ms
floods the DSP with test IPC's for the duration(in ms) specified.
The test stats such as average, min and max IPC response times
are logged in the dmesg and saved in the debugfs entry cache buffer.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add a new class of IPC command along with the first
test type, IPC_FLOOD, which will be used for flooding the DSP
with IPCs.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Timer will be reset when DSP is powered down. So the time stamp of trace
log will be reset after resume. Send time stamp to FW can align the time
stamp and avoid reset time stamp in trace log.
Signed-off-by: Bard liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/greentime/linux
Pull nds32 fixes from Greentime Hu:
- fix warning for math-emu
- fix nds32 fpu exception handling
- fix nds32 fpu emulation implementation
* tag 'nds32-for-linux-5.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/greentime/linux:
nds32: add new emulations for floating point instruction
nds32: Avoid IEX status being incorrectly modified
math-emu: Use statement expressions to fix Wshift-count-overflow warning
|
|
Pull sparc fixes from David Miller:
"Three bug fixes, and TLB flushing one is of particular brown paper bag
quality..."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc: perf: fix updated event period in response to PERF_EVENT_IOC_PERIOD
mdesc: fix a missing-check bug in get_vdev_port_node_info()
sparc64: Fix regression in non-hypervisor TLB flush xcall
|
|
Pull virtio fixes from Michael Tsirkin:
"Several fixes, some of them for CVEs"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vhost: scsi: add weight support
vhost: vsock: add weight support
vhost_net: fix possible infinite loop
vhost: introduce vhost_exceeds_weight()
virtio: Fix indentation of VIRTIO_MMIO
virtio: add unlikely() to WARN_ON_ONCE()
|
|
Add enumerations to support mux/demux processing component.
Signed-off-by: Jaska Uimonen <jaska.uimonen@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The definitions for DSP oops structures were not aligned
correctly to current FW ABI version 3.6.0, leading to
invalid data being printed out to debug logs. Fix the structs
and update related platform code accordingly.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add soundwire dai type and update ABI version.
Signed-off-by: Pan Xiuli <xiuli.pan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The HIPCCTL register controls the IPC interrupts. It can be set or
cleared to mask or enable these interrupts, but it makes no sense to
read and test its fields in an interrupt (which can only executed if
its fields are set).
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Align with Skylake driver and enable the IRQ at end of handler,
instead of at beginning.
Also add an error log if we have nothing to do in this handler.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Align with hardware recommended sequences, and read all IPC registers
before doing any other actions. Playing with BUSY and DONE bits may
invalidate values.
The values read may not actually be necessary but at least this
provides a snapshot of the IPC registers with no consistency issues.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Align with Skylake driver and enable the IRQ at end of handler,
instead of at beginning.
Also add an error log if we have nothing to do in this handler.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Move all register access to cnl_ipc_host_done()
No functionality change.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Align with hardware recommended sequences, and read all IPC registers
before doing any other actions. Playing with BUSY and DONE bits may
invalidate values.
The values read may not actually be necessary but at least this
provides a snapshot of the IPC registers with no consistency issues.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We use shim registers only to notify the other
side that a message was sent. The actual information
for the message is transmitted via mailbox.
cmd information inside shim register is not used by
the DSP, so we remove it to avoid confusion.
Signed-off-by: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add mode parameter for snd_sof_debugfs_buf_item() to specify
the mode while creating debugfs entries.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Using component driver as a name is not unique and it breaks audio in
certain configurations, e.g. Hardkernel Odroid XU3 board where following
components are registered:
- "3830000.i2s" with driver name "snd_dmaengine_pcm"
- "3830000.i2s-sec" with driver name "snd_dmaengine_pcm"
- "3830000.i2s" with driver name "samsung-i2s"
This reverts commit b19671d6caf1ac393681864d5d85dda9fa99a448.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add support of identification registers in STM32 SAI.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
HDA_DEV_ASOC type codec device refcounts are managed differently
from HDA_DEV_LEGACY devices. The refcount is released explicitly
in snd_hdac_ext_bus_device_remove() for ASOC type devices.
So, remove the put_device() call in snd_hda_codec_dev_free()
for such devices to make the refcount balanced. This will prevent
the NULL pointer exception when the codec driver is released
after the card is freed.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Previously the structure used bitfields, which do not guarantee bit
ordering.
This change makes sure the order is clearly defined. It also renames
and repurposes the field for general use.
Signed-off-by: Slawomir Blauciak <slawomir.blauciak@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We had a couple of misses with ABI changes, e.g. for Xtensa oops
information and the integration of sound trigger, before we set-up a
formal process to track evolutions.
With this patch, the SOF kernel patches are officially aligned with
the firmware 3.6 level. Changing this level has no impact on existing
users and is fully backwards-compatible.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add soundwire dai type and update ABI version.
Signed-off-by: Pan Xiuli <xiuli.pan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We missed these two definitions for GDB support and component
notifications, they are defined for the SOF firmware. Since they are
not used by the kernel so far, we can still add them without any ABI
change.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This tablet has an incorrect acpi identifier just like
Thinkpad10 tablet, which is why it is trying to load the RT5640 driver
instead of the RT5762 driver. The RT5640 driver, on the other hand, checks
the hardware ID, so no driver are loaded during boot. This fix resolves to
load the RT5672 driver on this tablet during boot. It also provides the
correct IO configuration, like the jack detect mode 3, for 1.8V pullup. I
would like to thank Pierre-Louis Bossart for helping with this patch.
Signed-off-by: Kovács Tamás <kepszlok@zohomail.eu>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The im_boffset field is in units of bytes, whereas XFS_INO_OFFSET
returns a value in units of inodes. Convert the units so that scrub on
a 64k-block filesystem works correctly.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
|
|
In the call to regmap_update_bits() for SLOTTYPE, the mask and value
fields are exchanged. Fix this.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Fixes: 41fd4caeb00b ("mmc: sdhci_am654: Add Initial Support for AM654 SDHCI driver")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
In case memory resources for *fw* were successfully allocated,
release them before return.
Addresses-Coverity-ID: 1445499 ("Resource leak")
Fixes: 5c9ae5a87573 ("usb: typec: ucsi: ccg: add firmware flashing support")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The debugfs interface for accessing DRAM virtual addresses currently
uses the 12 LSBs of a virtual address as an offset.
However, it should use the 20 LSBs in case the device MMU page size is
2MB instead of 4KB.
This patch fixes the offset calculation to be based on the page size.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
|
|
Depends on:
- https://patchwork.freedesktop.org/series/58976/
- https://patchwork.freedesktop.org/series/59855/
Reported-by: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: James Qian Wang (Arm Technology China) <james.qian.wang@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
|
|
As explained in
0cc3cd21657b ("cpu/hotplug: Boot HT siblings at least once")
we always, no matter what, have to bring up x86 HT siblings during boot at
least once in order to avoid first MCE bringing the system to its knees.
That means that whenever 'nosmt' is supplied on the kernel command-line,
all the HT siblings are as a result sitting in mwait or cpudile after
going through the online-offline cycle at least once.
This causes a serious issue though when a kernel, which saw 'nosmt' on its
commandline, is going to perform resume from hibernation: if the resume
from the hibernated image is successful, cr3 is flipped in order to point
to the address space of the kernel that is being resumed, which in turn
means that all the HT siblings are all of a sudden mwaiting on address
which is no longer valid.
That results in triple fault shortly after cr3 is switched, and machine
reboots.
Fix this by always waking up all the SMT siblings before initiating the
'restore from hibernation' process; this guarantees that all the HT
siblings will be properly carried over to the resumed kernel waiting in
resume_play_dead(), and acted upon accordingly afterwards, based on the
target kernel configuration.
Symmetricaly, the resumed kernel has to push the SMT siblings to mwait
again in case it has SMT disabled; this means it has to online all
the siblings when resuming (so that they come out of hlt) and offline
them again to let them reach mwait.
Cc: 4.19+ <stable@vger.kernel.org> # v4.19+
Debugged-by: Thomas Gleixner <tglx@linutronix.de>
Fixes: 0cc3cd21657b ("cpu/hotplug: Boot HT siblings at least once")
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
In a rare case, flush_tlb_kernel_range() could be called with a start
higher than the end.
In vm_remove_mappings(), in case page_address() returns 0 for all pages
(for example they were all in highmem), _vm_unmap_aliases() will be
called with start = ULONG_MAX, end = 0 and flush = 1.
If at the same time, the vmalloc purge operation is triggered by something
else while the current operation is between remove_vm_area() and
_vm_unmap_aliases(), then the vm mapping just removed will be already
purged. In this case the call of vm_unmap_aliases() may not find any other
mappings to flush and so end up flushing start = ULONG_MAX, end = 0. So
only set flush = true if we find something in the direct mapping that we
need to flush, and this way this can't happen.
Signed-off-by: Rick Edgecombe <rick.p.edgecombe@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Meelis Roos <mroos@linux.ee>
Cc: Nadav Amit <namit@vmware.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 868b104d7379 ("mm/vmalloc: Add flag for freeing of special permsissions")
Link: https://lkml.kernel.org/r/20190527211058.2729-3-rick.p.edgecombe@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The calculation of the direct map address range to flush was wrong.
This could cause the RO direct map alias to not get flushed. Today
this shouldn't be a problem because this flush is only needed on x86
right now and the spurious fault handler will fix cached RO->RW
translations. In the future though, it could cause the permissions
to remain RO in the TLB for the direct map alias, and then the page
would return from the page allocator to some other component as RO
and cause a crash.
So fix fix the address range calculation so the flush will include the
direct map range.
Signed-off-by: Rick Edgecombe <rick.p.edgecombe@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Meelis Roos <mroos@linux.ee>
Cc: Nadav Amit <namit@vmware.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 868b104d7379 ("mm/vmalloc: Add flag for freeing of special permsissions")
Link: https://lkml.kernel.org/r/20190527211058.2729-2-rick.p.edgecombe@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Add kerneldoc comments to pm_suspend_via_firmware(),
pm_resume_via_firmware() and pm_suspend_via_s2idle()
to explain what they do.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Save RING_HEAD into vgpu reg when vgpu switched out and report
it's value back to guest.
v6: addressed comment for ring head wrap count support. (Zhenyu)
v5: ring head wrap count support.
v4: updated HEAD/TAIL with guest value, not host value. (Yan Zhao)
v3: save RING HEAD/TAIL vgpu reg in save_ring_hw_state. (Zhenyu Wang)
v2: save RING_TAIL as well during vgpu mmio switch to meet ring_is_idle
condition. (Fred Gao)
v1: based on input from Weinan. (Weinan Li)
[zhenyuw: Include this fix for possible future guest kernel that
would utilize RING_HEAD for hangcheck.]
Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Xiaolin Zhang <xiaolin.zhang@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
|
