| Age | Commit message (Collapse) | Author |
|---|
|
Andrey found a way to trigger the WARN_ON_ONCE(delta < len) in
skb_try_coalesce() using syzkaller and a filter attached to a TCP
socket.
As we did recently in commit 158f323b9868 ("net: adjust skb->truesize in
pskb_expand_head()") we can adjust skb->truesize from ___pskb_trim(),
via a call to skb_condense().
If all frags were freed, then skb->truesize can be recomputed.
This call can be done if skb is not yet owned, or destructor is
sock_edemux().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Andrey found a way to trigger the WARN_ON_ONCE(delta < len) in
skb_try_coalesce() using syzkaller and a filter attached to a TCP
socket over loopback interface.
I believe one issue with looped skbs is that tcp_trim_head() can end up
producing skb with under estimated truesize.
It hardly matters for normal conditions, since packets sent over
loopback are never truncated.
Bytes trimmed from skb->head should not change skb truesize, since
skb->head is not reallocated.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On slave list updates, the bonding driver computes its hard_header_len
as the maximum of all enslaved devices's hard_header_len.
If the slave list is empty, e.g. on last enslaved device removal,
ETH_HLEN is used.
Since the bonding header_ops are set only when the first enslaved
device is attached, the above can lead to header_ops->create()
being called with the wrong skb headroom in place.
If bond0 is configured on top of ipoib devices, with the
following commands:
ifup bond0
for slave in $BOND_SLAVES_LIST; do
ip link set dev $slave nomaster
done
ping -c 1 <ip on bond0 subnet>
we will obtain a skb_under_panic() with a similar call trace:
skb_push+0x3d/0x40
push_pseudo_header+0x17/0x30 [ib_ipoib]
ipoib_hard_header+0x4e/0x80 [ib_ipoib]
arp_create+0x12f/0x220
arp_send_dst.part.19+0x28/0x50
arp_solicit+0x115/0x290
neigh_probe+0x4d/0x70
__neigh_event_send+0xa7/0x230
neigh_resolve_output+0x12e/0x1c0
ip_finish_output2+0x14b/0x390
ip_finish_output+0x136/0x1e0
ip_output+0x76/0xe0
ip_local_out+0x35/0x40
ip_send_skb+0x19/0x40
ip_push_pending_frames+0x33/0x40
raw_sendmsg+0x7d3/0xb50
inet_sendmsg+0x31/0xb0
sock_sendmsg+0x38/0x50
SYSC_sendto+0x102/0x190
SyS_sendto+0xe/0x10
do_syscall_64+0x67/0x180
entry_SYSCALL64_slow_path+0x25/0x25
This change addresses the issue avoiding updating the bonding device
hard_header_len when the slaves list become empty, forbidding to
shrink it below the value used by header_ops->create().
The bug is there since commit 54ef31371407 ("[PATCH] bonding: Handle large
hard_header_len") but the panic can be triggered only since
commit fc791b633515 ("IB/ipoib: move back IB LL address into the hard
header").
Reported-by: Norbert P <noe@physik.uzh.ch>
Fixes: 54ef31371407 ("[PATCH] bonding: Handle large hard_header_len")
Fixes: fc791b633515 ("IB/ipoib: move back IB LL address into the hard header")
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Upper layer GRO handlers can not handle IP fragments, so
exit GRO processing in this case.
This fixes ESP GRO because the packet must be reassembled
before we can decapsulate, otherwise we get authentication
failures.
It also aligns IPv4 to IPv6 where packets with fragmentation
headers are not passed to upper layer GRO handlers.
Fixes: 7785bba299a8 ("esp: Add a software GRO codepath")
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Tony Lindgren reports a kernel oops that resulted from my compile-time
fix on the default config. This shows two problems:
a) configurations that did not already enable PTP_1588_CLOCK will
now miss the cpts driver
b) when cpts support is disabled, the driver crashes. This is a
preexisting problem that we did not notice before my patch.
While the second problem is still being investigated, this modifies
the dependencies again, getting us back to the original state, with
another 'select NET_PTP_CLASSIFY' added in to avoid the original
link error we got, and the 'depends on POSIX_TIMERS' to hide
the CPTS support when turning it on would be useless.
Cc: stable@vger.kernel.org # 4.11 needs this
Fixes: 07fef3623407 ("cpsw/netcp: cpts depends on posix_timers")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit c49c097610fe ("ipmi: Don't call receive handler in the
panic context") means that the panic_recv_free is not called during a
panic and the atomic count does not drop to 0.
Fix this by only expecting one decrement of the atomic variable
which comes from panic_smi_free.
Signed-off-by: Robert Lippert <rlippert@google.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
|
|
Daniel Borkmann says:
====================
Misc BPF updates
This set cleans up ldimm64 leftovers from early eBPF days and
adds couple of test cases related to this to the verifier test
suite. It also cleans up the kallsyms spinlock (had same patch
also in queue) by relaxing it through switching to _bh variant.
It fixes up test_progs in relation to htons/ntohs and adds
accessor macros for the percpu tests in test_maps.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To overcome bugs as described and fixed in 89087c456fb5 ("bpf: Fix
values type used in test_maps"), provide a generic BPF_DECLARE_PERCPU()
and bpf_percpu() accessor macro for all percpu map values used in
tests.
Declaring variables works as follows (also works for structs):
BPF_DECLARE_PERCPU(uint32_t, my_value);
They can then be accessed normally as uint32_t type through:
bpf_percpu(my_value, <cpu_nr>)
For example:
bpf_percpu(my_value, 0)++;
Implicitly, we make sure that the passed type is allocated and aligned
by gcc at least on a 8-byte boundary, so that it works together with
the map lookup/update syscall for percpu maps. We use it as a usage
example in test_maps, so that others are free to adapt this into their
code when necessary.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Dave reported that on sparc test_progs generates buggy swapped
eth->h_proto protocol comparisons:
10: (15) if r3 == 0xdd86 goto pc+9
R0=imm2,min_value=2,max_value=2 R1=pkt(id=0,off=0,r=14) R2=pkt_end R3=inv
R4=pkt(id=0,off=14,r=14) R5=inv56 R10=fp
This is due to the unconditional ...
#define htons __builtin_bswap16
#define ntohs __builtin_bswap16
... in test_progs that causes this. Make use of asm/byteorder.h
and use __constant_htons() where possible and only perform the
bswap16 when on little endian in non-constant case.
Fixes: 6882804c916b ("selftests/bpf: add a test for overlapping packet range checks")
Fixes: 37821613626e ("selftests/bpf: add l4 load balancer test based on sched_cls")
Reported-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Hannes rightfully spotted that the bpf_lock doesn't need to be
irqsave variant. We never perform any such updates where this
would be necessary (neither right now nor in future), therefore
relax this further.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add several test cases around ldimm64, fp arithmetic and direct
packet access.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For both cases, the verifier is already rejecting such invalid
formed instructions. Thus, remove these artifacts from old times
and align it with ppc64, sparc64 and s390x JITs that don't have
them in the first place.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec-next
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2017-04-28
Just one patch to fix a misplaced spin_unlock_bh in an error path.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec
Steffen Klassert says:
====================
pull request (net): ipsec 2017-04-28
1) Do garbage collecting after a policy flush to remove old
bundles immediately. From Xin Long.
2) Fix GRO if netfilter is not defined.
From Sabrina Dubroca.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
cgroup_get() expected to be called only on live cgroups and triggers
warning on a dead cgroup; however, cgroup_sk_alloc() may be called
while cloning a socket which is left in an empty and removed cgroup
and thus may legitimately duplicate its reference on a dead cgroup.
This currently triggers the following warning spuriously.
WARNING: CPU: 14 PID: 0 at kernel/cgroup.c:490 cgroup_get+0x55/0x60
...
[<ffffffff8107e123>] __warn+0xd3/0xf0
[<ffffffff8107e20e>] warn_slowpath_null+0x1e/0x20
[<ffffffff810ff465>] cgroup_get+0x55/0x60
[<ffffffff81106061>] cgroup_sk_alloc+0x51/0xe0
[<ffffffff81761beb>] sk_clone_lock+0x2db/0x390
[<ffffffff817cce06>] inet_csk_clone_lock+0x16/0xc0
[<ffffffff817e8173>] tcp_create_openreq_child+0x23/0x4b0
[<ffffffff818601a1>] tcp_v6_syn_recv_sock+0x91/0x670
[<ffffffff817e8b16>] tcp_check_req+0x3a6/0x4e0
[<ffffffff81861ba3>] tcp_v6_rcv+0x693/0xa00
[<ffffffff81837429>] ip6_input_finish+0x59/0x3e0
[<ffffffff81837cb2>] ip6_input+0x32/0xb0
[<ffffffff81837387>] ip6_rcv_finish+0x57/0xa0
[<ffffffff81837ac8>] ipv6_rcv+0x318/0x4d0
[<ffffffff817778c7>] __netif_receive_skb_core+0x2d7/0x9a0
[<ffffffff81777fa6>] __netif_receive_skb+0x16/0x70
[<ffffffff81778023>] netif_receive_skb_internal+0x23/0x80
[<ffffffff817787d8>] napi_gro_frags+0x208/0x270
[<ffffffff8168a9ec>] mlx4_en_process_rx_cq+0x74c/0xf40
[<ffffffff8168b270>] mlx4_en_poll_rx_cq+0x30/0x90
[<ffffffff81778b30>] net_rx_action+0x210/0x350
[<ffffffff8188c426>] __do_softirq+0x106/0x2c7
[<ffffffff81082bad>] irq_exit+0x9d/0xa0 [<ffffffff8188c0e4>] do_IRQ+0x54/0xd0
[<ffffffff8188a63f>] common_interrupt+0x7f/0x7f <EOI>
[<ffffffff8173d7e7>] cpuidle_enter+0x17/0x20
[<ffffffff810bdfd9>] cpu_startup_entry+0x2a9/0x2f0
[<ffffffff8103edd1>] start_secondary+0xf1/0x100
This patch renames the existing cgroup_get() with the dead cgroup
warning to cgroup_get_live() after cgroup_kn_lock_live() and
introduces the new cgroup_get() which doesn't check whether the cgroup
is live or dead.
All existing cgroup_get() users except for cgroup_sk_alloc() are
converted to use cgroup_get_live().
Fixes: d979a39d7242 ("cgroup: duplicate cgroup reference when cloning sockets")
Cc: stable@vger.kernel.org # v4.5+
Cc: Johannes Weiner <hannes@cmpxchg.org>
Reported-by: Chris Mason <clm@fb.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Another set of patches for -next:
* API support for concurrent scheduled scan requests
* API changes for roaming reporting
* BSS max idle support in mac80211
* API changes for TX status reporting in mac80211
* API changes for RX rate reporting in mac80211
* rewrite monitor logic to prepare for BPF filters
* bugfix for rare devices without 2.4 GHz support
* a bugfix for recent DFS changes
* some further cleanups
The API changes are actually at a nice time, since it's
typically quiet just before the merge window, and trees
can be synchronized easily during it.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fix from Dmitry Torokhov:
"Yet another quirk to i8042 to get touchpad recognized on some laptops"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: i8042 - add Clevo P650RS to the i8042 reset list
|
|
When the base driver is enabled but all SoC specific drivers are turned
off, we now get a build error after code was added to always refer to the
clk gates:
drivers/clk/built-in.o: In function `ccu_pll_notifier_cb':
:(.text+0x154f8): undefined reference to `ccu_gate_helper_disable'
:(.text+0x15504): undefined reference to `ccu_gate_helper_enable'
This changes the Kconfig to always require the gate code to be built-in
when CONFIG_SUNXI_CCU is set.
Fixes: 02ae2bc6febd ("clk: sunxi-ng: Add clk notifier to gate then ungate PLL clocks")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fix from Chris Mason:
"We have one more fix for btrfs.
This gets rid of a new WARN_ON from rc1 that ended up making more
noise than we really want. The larger fix for the underflow got
delayed a bit and it's better for now to put it under
CONFIG_BTRFS_DEBUG"
* 'for-linus-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
btrfs: qgroup: move noisy underflow warning to debugging build
|
|
Parthasarathy Bhuvaragan says:
====================
tipc: fix hanging socket connections
This patch series contains fixes for the socket layer to
prevent hanging / stale connections.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a socket is shutting down, we notify the peer node about the
connection termination by reusing an incoming message if possible.
If the last received message was a connection acknowledgment
message, we reverse this message and set the error code to
TIPC_ERR_NO_PORT and send it to peer.
In tipc_sk_proto_rcv(), we never check for message errors while
processing the connection acknowledgment or probe messages. Thus
this message performs the usual flow control accounting and leaves
the session hanging.
In this commit, we terminate the connection when we receive such
error messages.
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Until now, the checks for sockets in CONNECTING state was based on
the assumption that the incoming message was always from the
peer's accepted data socket.
However an application using a non-blocking socket sends an implicit
connect, this socket which is in CONNECTING state can receive error
messages from the peer's listening socket. As we discard these
messages, the application socket hangs as there due to inactivity.
In addition to this, there are other places where we process errors
but do not notify the user.
In this commit, we process such incoming error messages and notify
our users about them using sk_state_change().
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In filter_connect, we use waitqueue_active() to check for any
connections to wakeup. But waitqueue_active() is missing memory
barriers while accessing the critical sections, leading to
inconsistent results.
In this commit, we replace this with an SMP safe wq_has_sleeper()
using the generic socket callback sk_data_ready().
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 99e6608c9e74 "block: Add badblock management for gendisks"
allowed for drivers like pmem and software-raid to advertise a list of
bad media areas. However, it inadvertently added a 'badblocks' to all
block devices. Lets clean this up by having the 'badblocks' attribute
not be visible when the driver has not populated a 'struct badblocks'
instance in the gendisk.
Cc: Jens Axboe <axboe@fb.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Reported-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Tested-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
http://git.kernel.org/pub/scm/linux/kernel/git/horms/ipvs
Simon Horman says:
====================
IPVS Fixes for v4.11
I would also like it considered for stable.
* Explicitly forbid ipv6 service/dest creation if ipv6 mod is disabled
to avoid oops caused by IPVS accesing IPv6 routing code in such
circumstances.
====================
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
The commit 6d684e54690c ("rhashtable: Cap total number of entries
to 2^31") breaks rhashtable users that do not set max_size. This
is because when max_size is zero max_elems is also incorrectly set
to zero instead of 2^31.
This patch fixes it by only lowering max_elems when max_size is not
zero.
Fixes: 6d684e54690c ("rhashtable: Cap total number of entries to 2^31")
Reported-by: Florian Fainelli <f.fainelli@gmail.com>
Reported-by: kernel test robot <fengguang.wu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The only difference between ->run_work and ->delay_work, is that
the latter is used to defer running a queue. This is done by
marking the queue stopped, and scheduling ->delay_work to run
sometime in the future. While the queue is stopped, direct runs
or runs through ->run_work will not run the queue.
If we combine the handlers, then we need to handle two things:
1) If a delayed/stopped run is scheduled, then we should not run
the queue before that has been completed.
2) If a queue is delayed/stopped, the handler needs to restart
the queue. Normally a run of a queue with the stopped bit set
would be a no-op.
Case 1 is handled by modifying a currently pending queue run
to the deadline set by the caller of blk_mq_delay_queue().
Subsequent attempts to queue a queue run will find the work
item already pending, and direct runs will see a stopped queue
as before.
Case 2 is handled by adding a new bit, BLK_MQ_S_START_ON_RUN,
that tells the work handler that it should clear a stopped
queue and run the handler.
Reviewed-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
This modifies (or adds, if not currently pending) an existing
delayed work item.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
They serve the exact same purpose. Get rid of the non-delayed
work variant, and just run it without delay for the normal case.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
list_for_each_entry() isn't super safe if we're freeing the objects
while we traverse the list. Also don't bother taking the extra
reference, the module refcounting stuff will save us from having anybody
messing with the device while we're trying to unload.
Reported-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
According to my static checker we should unlock here before the return.
That seems reasonable to me as well.
Fixes" b9e69e127397 ("netfilter: xtables: don't hook tables by default")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Seems like this was forgotten in the bfq-series from Paolo. Let's do it now
so people don't miss out involving Paolo for any future changes or when
reporting bugs.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
mempool_alloc() cannot fail if the gfp flags allow it to
sleep, and both GFP_FS allows for sleeping.
So these tests of the return value from mempool_alloc()
cannot be needed.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Steve French <smfrench@gmail.com>
|
|
commit 620d8745b35d ("Introduce cifs_copy_file_range()") changes the
behaviour of the cifs ioctl call CIFS_IOC_COPYCHUNK_FILE. In case of
successful writes, it now returns the number of bytes written. This
return value is treated as an error by the xfstest cifs/001. Depending
on the errno set at that time, this may or may not result in the test
failing.
The patch fixes this by setting the return value to 0 in case of
successful writes.
Fixes: commit 620d8745b35d ("Introduce cifs_copy_file_range()")
Reported-by: Eryu Guan <eguan@redhat.com>
Signed-off-by: Sachin Prabhu <sprabhu@redhat.com>
Acked-by: Pavel Shilovsky <pshilov@microsoft.com>
Cc: stable@vger.kernel.org
Signed-off-by: Steve French <smfrench@gmail.com>
|
|
Incorrect return value for shares not using the prefix path means that
we will never match superblocks for these shares.
Fixes: commit c1d8b24d1819 ("Compare prepaths when comparing superblocks")
Cc: stable@vger.kernel.org
Signed-off-by: Sachin Prabhu <sprabhu@redhat.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Steve French <smfrench@gmail.com>
|
|
The ls1046a datasheet specified that the max SD clock frequency
for eSDHC SDR104/HS200 was 167MHz, and the ls1012a datasheet
specified it's 125MHz for ls1012a. So this patch is to add the
limitation.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Have proper request id filled in the SCHED_SCAN_RESULTS and
SCHED_SCAN_STOPPED notifications toward user-space by having the
driver provide it through the api.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The loop to poll ESDHC_CLOCK_STABLE bit with mdelay would waste time
because the time to stabilize is much less than 1 ms. This patch is
to use udelay instead to avoid time wasting.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The default value of LOGIC_TIMING_ADJUST register in eMMC 5.0 PHY is
different from that in eMMC 5.1 PHY. Set the specific value for that
register in eMMC 5.0 PHY.
Signed-off-by: Hu Ziji <huziji@marvell.com>
Reported-by: Jisheng Zhang <jszhang@marvell.com>
Tested-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
sdhci_remove_host() might execute SOFT_RESET_ALL. Inside xenon_remove(),
Xenon SDHC should be enabled during sdhci_remove_host().
Move xenon_sdhc_unprepare after sdhci_remove_host() such that Xenon SDHC is
disabled after sdhci_remove_host() completes.
Signed-off-by: Hu Ziji <huziji@marvell.com>
Reported-by: Jisheng Zhang <jszhang@marvell.com>
Tested-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Parse the BSS max idle period element and set the BSS configuration
accordingly so the driver can use this information to configure the
max idle period and to use protected management frames for keep alive
when required.
The BSS max idle period element is defined in IEEE802.11-2016,
section 9.4.2.79
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
cfg80211_roamed() and cfg80211_roamed_bss() take the same arguments
except that cfg80211_roamed() requires the BSSID and
cfg80211_roamed_bss() requires the bss entry.
Unify the two functions by using a struct for driver initiated
roaming information so that either the BSSID or the bss entry can be
passed as an argument to the unified function.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
[modified the ath6k, brcm80211, rndis and wlan-ng drivers accordingly]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
[modify brcmfmac to remove the useless cast, spotted by Arend]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Existing API 'ieee80211_get_sdata_band' returns default 2 GHz band even
if the channel context configuration is NULL. This crashes for chipsets
which support 5 Ghz alone when it tries to access members of 'sband'.
Channel context configuration can be NULL in multivif case and when
channel switch is in progress (or) when it fails. Fix this by replacing
the API 'ieee80211_get_sdata_band' with 'ieee80211_get_sband' which
returns a NULL pointer for sband when the channel configuration is NULL.
An example scenario is as below:
In multivif mode (AP + STA) with drivers like ath10k, when we do a
channel switch in the AP vif (which has a number of clients connected)
and a STA vif which is connected to some other AP, when the channel
switch in AP vif fails, while the STA vifs tries to connect to the
other AP, there is a window where the channel context is NULL/invalid
and this results in a crash while the clients connected to the AP vif
tries to reconnect and this race is very similar to the one investigated
by Michal in https://patchwork.kernel.org/patch/3788161/ and this does
happens with hardware that supports 5Ghz alone after long hours of
testing with continuous channel switch on the AP vif
ieee80211 phy0: channel context reservation cannot be finalized because
some interfaces aren't switching
wlan0: failed to finalize CSA, disconnecting
wlan0-1: deauthenticating from 8c:fd:f0:01:54:9c by local choice
(Reason: 3=DEAUTH_LEAVING)
WARNING: CPU: 1 PID: 19032 at net/mac80211/ieee80211_i.h:1013 sta_info_alloc+0x374/0x3fc [mac80211]
[<bf77272c>] (sta_info_alloc [mac80211])
[<bf78776c>] (ieee80211_add_station [mac80211]))
[<bf73cc50>] (nl80211_new_station [cfg80211])
Unable to handle kernel NULL pointer dereference at virtual
address 00000014
pgd = d5f4c000
Internal error: Oops: 17 [#1] PREEMPT SMP ARM
PC is at sta_info_alloc+0x380/0x3fc [mac80211]
LR is at sta_info_alloc+0x37c/0x3fc [mac80211]
[<bf772738>] (sta_info_alloc [mac80211])
[<bf78776c>] (ieee80211_add_station [mac80211])
[<bf73cc50>] (nl80211_new_station [cfg80211]))
Cc: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When creating a new ipvs service, ipv6 addresses are always accepted
if CONFIG_IP_VS_IPV6 is enabled. On dest creation the address family
is not explicitly checked.
This allows the user-space to configure ipvs services even if the
system is booted with ipv6.disable=1. On specific configuration, ipvs
can try to call ipv6 routing code at setup time, causing the kernel to
oops due to fib6_rules_ops being NULL.
This change addresses the issue adding a check for the ipv6
module being enabled while validating ipv6 service operations and
adding the same validation for dest operations.
According to git history, this issue is apparently present since
the introduction of ipv6 support, and the oops can be triggered
since commit 09571c7ae30865ad ("IPVS: Add function to determine
if IPv6 address is local")
Fixes: 09571c7ae30865ad ("IPVS: Add function to determine if IPv6 address is local")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
|
|
The sync_refresh_period variable is unsigned, so it can never be < 0.
Signed-off-by: Aaron Conole <aconole@bytheb.org>
Signed-off-by: Simon Horman <horms@verge.net.au>
|
|
There are no in-tree callers of this function and it isn't exported.
Signed-off-by: Aaron Conole <aconole@bytheb.org>
Signed-off-by: Simon Horman <horms@verge.net.au>
|
|
This allows the driver to pass in struct ieee80211_tx_status directly.
Make ieee80211_tx_status_noskb a wrapper around it.
As with ieee80211_tx_status_noskb, there is no _ni variant of this call,
because it probably won't be needed.
Even if the driver won't provide any extra status info other than what's
in struct ieee80211_tx_info already, it can optimize status reporting
this way by passing in the station pointer.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
[use C99 initializers]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Makes further cleanups more readable
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Rename .tx_status_noskb to .tx_status_ext and pass a new on-stack
struct ieee80211_tx_status instead of struct ieee80211_tx_info.
This struct can be used to pass extra information, e.g. for dynamic tx
power control
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Instead of hand-coding the bit manipulations, use the bitfield
macros to generate the code for the encoded bitrate.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
