| Age | Commit message (Collapse) | Author |
|---|
|
The BCM2835 SPI driver needs to set up the clock polarity in its
->prepare_message() hook before spi_transfer_one_message() asserts chip
select to avoid a gratuitous clock signal edge (cf. commit acace73df2c1
("spi: bcm2835: set up spi-mode before asserting cs-gpio")).
Precalculate the CS register value (which selects the clock polarity)
once in ->setup() and use that cached value in ->prepare_message() and
->transfer_one(). This avoids one MMIO read per message and one per
transfer, yielding a small latency improvement. Additionally, a
forthcoming commit will use the precalculated value to derive the
register value for clearing the RX FIFO, which will eliminate the need
for an RX dummy buffer when performing TX-only DMA transfers.
Tested-by: Nuno Sá <nuno.sa@analog.com>
Tested-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Martin Sperl <kernel@martin.sperl.org>
Link: https://lore.kernel.org/r/d17c1d7fcdc97fffa961b8737cfd80eeb14f9416.1568187525.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Document the BCM2835 DMA driver's device data structure so that upcoming
commits may add further members with proper kerneldoc.
Tested-by: Nuno Sá <nuno.sa@analog.com>
Tested-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Martin Sperl <kernel@martin.sperl.org>
Cc: Florian Kauer <florian.kauer@koalo.de>
Link: https://lore.kernel.org/r/78648f80f67d97bb7beecc1b9be6b6e4a45bc1d8.1568187525.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
__spi_alloc_controller() uses a single allocation to accommodate struct
spi_controller and the driver-private data, but places the latter behind
the former. This order does not guarantee cacheline alignment of the
driver-private data. (It does guarantee cacheline alignment of struct
spi_controller but the structure doesn't make any use of that property.)
Round up struct spi_controller to cacheline size. A forthcoming commit
leverages this to grant DMA access to driver-private data of the BCM2835
SPI master.
An alternative, less economical approach would be to use two allocations.
A third approach consists of reversing the order to conserve memory.
But Mark Brown is concerned that it may result in a performance penalty
on architectures that don't like unaligned accesses.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/01625b9b26b93417fb09d2c15ad02dfe9cdbbbe5.1568187525.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The DMA engine API requires DMA drivers to explicitly allow that
descriptors are prepared once and reused multiple times. Only a
single driver makes use of this functionality so far (pxa_dma.c,
to speed up pxa_camera.c).
We're about to add another use case for reusable descriptors in
the BCM2835 SPI driver, so allow that in the BCM2835 DMA driver.
Tested-by: Nuno Sá <nuno.sa@analog.com>
Tested-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Martin Sperl <kernel@martin.sperl.org>
Cc: Florian Kauer <florian.kauer@koalo.de>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Link: https://lore.kernel.org/r/bfc98a38225bbec4158440ad06cb9eee675e3e6f.1568187525.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The BCM2835 DMA driver currently requests an interrupt from the
controller regardless whether or not the client has passed in the
DMA_PREP_INTERRUPT flag. This causes unnecessary overhead for cyclic
transactions which do not need an interrupt after each period.
We're about to add such a use case, namely cyclic clearing of the SPI
controller's RX FIFO, so amend the DMA driver to request an interrupt
only if DMA_PREP_INTERRUPT was passed in. Ignore the period_len for
such transactions and set it to the buffer length to make the driver's
calculations work.
Tested-by: Nuno Sá <nuno.sa@analog.com>
Tested-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Martin Sperl <kernel@martin.sperl.org>
Cc: Florian Kauer <florian.kauer@koalo.de>
Link: https://lore.kernel.org/r/73cf37be56eb4cbe6f696057c719f3a38cbaf26e.1568187525.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The BCM2835 SPI driver uses a flag to keep track of whether a DMA
transfer is in progress.
The flag is used to avoid terminating DMA channels multiple times if a
transfer finishes orderly while simultaneously the SPI core invokes the
->handle_err() callback because the transfer took too long. However
terminating DMA channels multiple times is perfectly fine, so the flag
is unnecessary for this particular purpose.
The flag is also used to avoid invoking bcm2835_spi_undo_prologue()
multiple times under this race condition. However multiple *concurrent*
invocations can no longer happen since commit 2527704d8411 ("spi:
bcm2835: Synchronize with callback on DMA termination") because the
->handle_err() callback now uses the _sync() variant when terminating
DMA channels.
The only raison d'être of the flag is therefore that
bcm2835_spi_undo_prologue() cannot cope with multiple *sequential*
invocations. Achieve that by setting tx_prologue to 0 at the end of
the function. Subsequent invocations thus become no-ops.
With that, the dma_pending flag becomes unnecessary, so drop it.
Tested-by: Nuno Sá <nuno.sa@analog.com>
Tested-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Martin Sperl <kernel@martin.sperl.org>
Link: https://lore.kernel.org/r/062b03b7f86af77a13ce0ec3b22e0bdbfcfba10d.1568187525.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
There is a spelling mistake in a mlx4_err error message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a spelling mistake in a .msg literal string. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a spelling mistake in the lmc_trace message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a spelling mistake in a dev_err message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In rds_bind(), an rds_sock is added to the RDS bind hash table before
rs_transport is set. This means that the socket can be found by the
receive code path when rs_transport is NULL. And the receive code
path de-references rs_transport for congestion update check. This can
cause a panic. An rds_sock should not be added to the bind hash table
before all the needed fields are set.
Reported-by: syzbot+4b4f8163c2e246df3c4c@syzkaller.appspotmail.com
Signed-off-by: Ka-Cheong Poon <ka-cheong.poon@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Layer 2 Update frame is used to update bridges when a station roams
to another AP even if that STA does not transmit any frames after the
reassociation. This behavior was described in IEEE Std 802.11F-2003 as
something that would happen based on MLME-ASSOCIATE.indication, i.e.,
before completing 4-way handshake. However, this IEEE trial-use
recommended practice document was published before RSN (IEEE Std
802.11i-2004) and as such, did not consider RSN use cases. Furthermore,
IEEE Std 802.11F-2003 was withdrawn in 2006 and as such, has not been
maintained amd should not be used anymore.
Sending out the Layer 2 Update frame immediately after association is
fine for open networks (and also when using SAE, FT protocol, or FILS
authentication when the station is actually authenticated by the time
association completes). However, it is not appropriate for cases where
RSN is used with PSK or EAP authentication since the station is actually
fully authenticated only once the 4-way handshake completes after
authentication and attackers might be able to use the unauthenticated
triggering of Layer 2 Update frame transmission to disrupt bridge
behavior.
Fix this by postponing transmission of the Layer 2 Update frame from
station entry addition to the point when the station entry is marked
authorized. Similarly, send out the VLAN binding update only if the STA
entry has already been authorized.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 414126f9e5abf1973c661d24229543a9458fa8ce.
This commit broke eMMC storage access on a new consumer MiniPC based on
AMD SoC, which has eMMC connected to:
02:00.0 SD Host controller: O2 Micro, Inc. Device 8620 (rev 01) (prog-if 01)
Subsystem: O2 Micro, Inc. Device 0002
During probe, several errors are seen including:
mmc1: Got data interrupt 0x02000000 even though no data operation was in progress.
mmc1: Timeout waiting for hardware interrupt.
mmc1: error -110 whilst initialising MMC card
Reverting this commit allows the eMMC storage to be detected & usable
again.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Fixes: 414126f9e5ab ("mmc: sdhci: Remove unneeded quirk2 flag of O2 SD host
controller")
Cc: stable@vger.kernel.org # v5.1+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The commit 37fefadee8bb ("mmc: bcm2835: Terminate timeout work
synchronously") causes lockups in case of hardware timeouts due the
timeout work also calling cancel_delayed_work_sync() on its own.
So revert it.
Fixes: 37fefadee8bb ("mmc: bcm2835: Terminate timeout work synchronously")
Cc: stable@vger.kernel.org
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190906131032.22148-1-yuehaibing@huawei.com
Acked-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Change all exported symbols for managed GPIO functions from
EXPORT_SYMBOL() to EXPORT_SYMBOL_GPL(), like is used for their
non-managed counterparts.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20190906084539.21838-5-geert+renesas@glider.be
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
All exported functions provide genuine Linux-specific functionality.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20190906084539.21838-4-geert+renesas@glider.be
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Since commit 9a95e8d25a140ba9 ("gpio: remove etraxfs driver"), there are
no more users of of_gpio_simple_xlate() outside gpiolib-of.c.
All GPIO drivers that need it now rely on of_gpiochip_add() setting it
up as the default translate function.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20190906084539.21838-3-geert+renesas@glider.be
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Since commit f626d6dfb7098525 ("gpio: of: Break out OF-only code"),
there are no more users of of_get_named_gpiod_flags() outside
gpiolib-of.c.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20190906084539.21838-2-geert+renesas@glider.be
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
'arm/qcom', 'arm/renesas', 'x86/amd', 'x86/vt-d' and 'core' into next
|
|
Despite the widespread and complete failure of Broadwell integrated
graphics when DMAR is enabled, known over the years, we have never been
able to root cause the issue. Instead, we let the failure undermine our
confidence in the iommu system itself when we should be pushing for it to
be always enabled. Quirk away Broadwell and remove the rotten apple.
References: https://bugs.freedesktop.org/show_bug.cgi?id=89360
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Lu Baolu <baolu.lu@linux.intel.com>
Cc: Martin Peres <martin.peres@linux.intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Reviewed-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Intel VT-d specification revision 3 added support for Scalable Mode
Translation for DMA remapping. Add the Scalable Mode fault reasons to
show detailed fault reasons when the translation fault happens.
Link: https://software.intel.com/sites/default/files/managed/c5/15/vt-directed-io-spec.pdf
Reviewed-by: Sohil Mehta <sohil.mehta@intel.com>
Signed-off-by: Kyung Min Park <kyung.min.park@intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The Intel VT-d hardware uses paging for DMA remapping.
The minimum mapped window is a page size. The device
drivers may map buffers not filling the whole IOMMU
window. This allows the device to access to possibly
unrelated memory and a malicious device could exploit
this to perform DMA attacks. To address this, the
Intel IOMMU driver will use bounce pages for those
buffers which don't fill whole IOMMU pages.
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: Kevin Tian <kevin.tian@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Tested-by: Xu Pengfei <pengfei.xu@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
This adds trace support for the Intel IOMMU driver. It
also declares some events which could be used to trace
the events when an IOVA is being mapped or unmapped in
a domain.
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: Kevin Tian <kevin.tian@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The bounce page implementation depends on swiotlb. Hence, don't
switch off swiotlb if the system has untrusted devices or could
potentially be hot-added with any untrusted devices.
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: Kevin Tian <kevin.tian@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
This adds a helper to check whether a device needs to
use bounce buffer. It also provides a boot time option
to disable the bounce buffer. Users can use this to
prevent the iommu driver from using the bounce buffer
for performance gain.
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: Kevin Tian <kevin.tian@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Tested-by: Xu Pengfei <pengfei.xu@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
This splits the size parameter to swiotlb_tbl_map_single() and
swiotlb_tbl_unmap_single() into an alloc_size and a mapping_size
parameter, where the latter one is rounded up to the iommu page
size.
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
regulator_uV_show() is missing error handling if regulator_get_voltage_rdev()
returns negative values. Instead it prints the errno as a string, e.g. -EINVAL
as "-22" which could be interpreted as -22 µV.
We also do not need to hold the lock while converting the integer to a string.
Reported-by: Adam Ford <aford173@gmail.com>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Tested-by: Adam Ford <aford173@gmail.com>
Link: https://lore.kernel.org/r/f37f2a1276efcb34cf3b7f1a25481175be048806.1568143348.git.hns@goldelico.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This fixes 11da04af0d3b, as devm_gpiod_get_from_of_node() does
not do translation "con-id" -> "con-id-gpios" that our bindings expects,
and therefore it was wrong to change connection ID to be simply "enable"
when moving to using devm_gpiod_get_from_of_node().
Fixes: 11da04af0d3b ("regulator: da9211: Pass descriptors instead of GPIO numbers")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/20190910170246.GA56792@dtor-ws
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This fixes 96392c3d8ca4, as devm_gpiod_get_from_of_node() does
not do translation "con-id" -> "con-id-gpios" that our bindings expects,
and therefore it was wrong to change connection ID to be simply
"maxim,ena" when moving to using devm_gpiod_get_from_of_node().
Fixes: 96392c3d8ca4 ("regulator: max77686: Pass descriptor instead of GPIO number")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/20190910170050.GA55530@dtor-ws
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The ast2600 is a new generation of SoC from ASPEED. Similarly to the
ast2400 and ast2500, it has a GPIO controller for it's 3.3V GPIO pins.
Additionally, it has a GPIO controller for 1.8V GPIO pins.
As the register names for both controllers are the same and the 36 1.8V
GPIOs and the first 36 of the 3.3V GPIOs are all bidirectional, we can
use the same configuration struct and use the ngpio property to
differentiate between the two sets of GPIOs.
Signed-off-by: Rashmica Gupta <rashmica.g@gmail.com>
Link: https://lore.kernel.org/r/20190906063737.15428-1-rashmica.g@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Use the ngpio property from the device tree if it exists. If it doesn't
then fallback to the hardcoded value in the config.
This is in preparation for adding ast2600 support. The ast2600 SoC has
two GPIO controllers and so requires two instances of the GPIO driver.
We use the ngpio property to different between them as they have
different numbers of GPIOs.
Signed-off-by: Rashmica Gupta <rashmica.g@gmail.com>
Link: https://lore.kernel.org/r/20190906062727.13521-1-rashmica.g@gmail.com
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This is in preparation for adding ast2600 support. The ast2600 SoC
requires two instances of the GPIO driver as it has two GPIO
controllers. Each instance needs it's own irqchip.
Signed-off-by: Rashmica Gupta <rashmica.g@gmail.com>
Link: https://lore.kernel.org/r/20190906062644.13445-1-rashmica.g@gmail.com
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The current calculation for the number of GPIO banks is only correct if
the number of GPIOs is a multiple of 32 (if there were 31 GPIOs we would
currently say there are 0 banks, which is incorrect).
Fixes: 361b79119a4b7 ('gpio: Add Aspeed driver')
Signed-off-by: Rashmica Gupta <rashmica.g@gmail.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20190906062623.13354-1-rashmica.g@gmail.com
Reviewed-by: Joel Stanley <joel@jms.d.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The ast2600 is a new generation of SoC from ASPEED. Similarly to the
ast2400 and ast2500, it has a GPIO controller for it's 3.3V GPIO pins.
Additionally, it has a GPIO controller for 36 1.8V GPIO pins. We use
the ngpio property to differentiate between these controllers.
Signed-off-by: Rashmica Gupta <rashmica.g@gmail.com>
Link: https://lore.kernel.org/r/20190906062547.13264-1-rashmica.g@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Another day; another DSDT bug we need to workaround...
Since commit ca876c7483b6 ("gpiolib-acpi: make sure we trigger edge events
at least once on boot") we call _AEI edge handlers at boot.
In some rare cases this causes problems. One example of this is the Minix
Neo Z83-4 mini PC, this device has a clear DSDT bug where it has some copy
and pasted code for dealing with Micro USB-B connector host/device role
switching, while the mini PC does not even have a micro-USB connector.
This code, which should not be there, messes with the DDC data pin from
the HDMI connector (switching it to GPIO mode) breaking HDMI support.
To avoid problems like this, this commit adds a new
gpiolib_acpi.run_edge_events_on_boot kernel commandline option, which
allows disabling the running of _AEI edge event handlers at boot.
The default value is -1/auto which uses a DMI based blacklist, the initial
version of this blacklist contains the Neo Z83-4 fixing the HDMI breakage.
Cc: stable@vger.kernel.org
Cc: Daniel Drake <drake@endlessm.com>
Cc: Ian W MORRISON <ianwmorrison@gmail.com>
Reported-by: Ian W MORRISON <ianwmorrison@gmail.com>
Suggested-by: Ian W MORRISON <ianwmorrison@gmail.com>
Fixes: ca876c7483b6 ("gpiolib-acpi: make sure we trigger edge events at least once on boot")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20190827202835.213456-1-hdegoede@redhat.com
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Ian W MORRISON <ianwmorrison@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Keep the "Library routines" menu intact by moving OBJAGG into it.
Otherwise OBJAGG is displayed/presented as an orphan in the
various config menus.
Fixes: 0a020d416d0a ("lib: introduce initial implementation of object aggregation manager")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Ido Schimmel <idosch@mellanox.com>
Cc: David S. Miller <davem@davemloft.net>
Tested-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sonic_send_packet will be processed in irq or non-irq
context, so it would better use dev_kfree_skb_any
instead of dev_kfree_skb.
Fixes: d9fb9f384292 ("*sonic/natsemi/ns83829: Move the National Semi-conductor drivers")
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In i2400m_op_rfkill_sw_toggle cmd buffer should be released along with
skb response.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After changing the valid_mask for the struct gpio_chip
to detect the need and presence of a valid mask with the
presence of a .init_valid_mask() callback to fill it in,
we augment the gpio_irq_chip to use the same logic.
Switch all driver using the gpio_irq_chio valid_mask
over to this new method.
This makes sure the valid_mask for the gpio_irq_chip gets
filled in when we add the gpio_chip, which makes it a
little easier to switch over drivers using the old
way of setting up gpio_irq_chip over to the new method
of passing the gpio_irq_chip along with the gpio_chip.
(See drivers/gpio/TODO for details.)
Cc: Joel Stanley <joel@jms.id.au>
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Link: https://lore.kernel.org/r/20190904140104.32426-1-linus.walleij@linaro.org
|
|
Add support for the Sensirion SHTC3 humidity and temperature sensor to
the shtc1 module.
Signed-off-by: Dan Robertson <dan@dlrobertson.com>
Link: https://lore.kernel.org/r/20190905014554.21658-2-dan@dlrobertson.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Fix an error in the bitmaskfor the shtc1 and shtw1 bitmask used to
retrieve the chip ID from the ID register. See section 5.7 of the shtw1
or shtc1 datasheet for details.
Fixes: 1a539d372edd9832444e7a3daa710c444c014dc9 ("hwmon: add support for Sensirion SHTC1 sensor")
Signed-off-by: Dan Robertson <dan@dlrobertson.com>
Link: https://lore.kernel.org/r/20190905014554.21658-3-dan@dlrobertson.com
[groeck: Reordered to be first in series and adjusted accordingly]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This issue causes SCTP_PEER_ADDR_THLDS sockopt not to be able to dump
a transport thresholds info.
Fix it by adding 'goto' put_user in sctp_getsockopt_paddr_thresholds.
Fixes: 8add543e369d ("sctp: add SCTP_FUTURE_ASSOC for SCTP_PEER_ADDR_THLDS sockopt")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case of TCA_HHF_NON_HH_WEIGHT or TCA_HHF_QUANTUM is zero,
it would make no progress inside the loop in hhf_dequeue() thus
kernel would get stuck.
Fix this by checking this corner case in hhf_change().
Fixes: 10239edf86f1 ("net-qdisc-hhf: Heavy-Hitter Filter (HHF) qdisc")
Reported-by: syzbot+bc6297c11f19ee807dc2@syzkaller.appspotmail.com
Reported-by: syzbot+041483004a7f45f1f20a@syzkaller.appspotmail.com
Reported-by: syzbot+55be5f513bed37fc4367@syzkaller.appspotmail.com
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: Terry Lam <vtlam@google.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
At least sch_red and sch_tbf don't implement ->tcf_block()
while still have a non-zero tc "class".
Instead of adding nop implementations to each of such qdisc's,
we can just relax the check of cops->tcf_block() in
tc_bind_tclass(). They don't support TC filter anyway.
Reported-by: syzbot+21b29db13c065852f64b@syzkaller.appspotmail.com
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It was recently discovered that the linux version of waitid is not a
superset of the other wait functions because it does not include support
for waiting for the current process group. This has two downsides:
1. An extra system call is needed to get the current process group.
2. After the current process group is received and before it is passed
to waitid a signal could arrive causing the current process group to change.
Inherent race-conditions as these make it impossible for userspace to
emulate this functionaly and thus violate async-signal safety
requirements for waitpid.
Arguments can be made for using a different choice of idtype and id
for this case but the BSDs already use this P_PGID and 0 to indicate
waiting for the current process's process group. So be nice to user
space programmers and don't introduce an unnecessary incompatibility.
Some people have noted that the posix description is that
waitpid will wait for the current process group, and that in
the presence of pthreads that process group can change. To get
clarity on this issue I looked at XNU, FreeBSD, and Luminos. All of
those flavors of unix waited for the current process group at the
time of call and as written could not adapt to the process group
changing after the call.
At one point Linux did adapt to the current process group changing but
that stopped in 161550d74c07 ("pid: sys_wait... fixes"). It has been
over 11 years since Linux has that behavior, no programs that fail
with the change in behavior have been reported, and I could not
find any other unix that does this. So I think it is safe to clarify
the definition of current process group, to current process group
at the time of the wait function.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Rich Felker <dalias@libc.org>
Cc: Alistair Francis <alistair23@gmail.com>
Cc: Zong Li <zongbox@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Florian Weimer <fweimer@redhat.com>
Cc: Adhemerval Zanella <adhemerval.zanella@linaro.org>
Cc: GNU C Library <libc-alpha@sourceware.org>
Link: https://lore.kernel.org/r/20190814154400.6371-2-christian.brauner@ubuntu.com
|
|
From 'perf stat', so that it can be used from multiple places.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Joe Mario <jmario@redhat.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Michael Petlan <mpetlan@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/20190902121255.536-2-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
So that this development header is properly installed and can be found
by tools linking with libperf.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Michael Petlan <mpetlan@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/20190901124822.10132-5-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Add a libperf build test, that is triggered when one does:
$ make -C tools/perf build-test
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Michael Petlan <mpetlan@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/20190901124822.10132-4-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
The python/perf.so compilation needs libperf ready, otherwise it fails:
$ make python/perf.so JOBS=1
BUILD: Doing 'make -j1' parallel build
GEN python/perf.so
gcc: error: /home/jolsa/kernel/linux-perf/tools/perf/lib/libperf.a: No such file or directory
Fixing this with by adding libperf dependency.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Michael Petlan <mpetlan@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/20190901124822.10132-2-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
