| Age | Commit message (Collapse) | Author |
|---|
|
arm/fixes
Apple SoC fixes for 6.15
This tag contains two small commits since rc1:
- Add a .mailmap entry requested by Asahi Lina to better filter her
emails
- Mark the power domains for the touchbar support introduced with 6.15
as always on since the driver cannot initialize the touchbar from
scratch after the domains are powered off (e.g. during suspend).
* tag 'asahi-soc-fixes-6.15' of https://github.com/AsahiLinux/linux:
arm64: dts: apple: touchbar: Mark ps_dispdfr_be as always-on
mailmap: Update email for Asahi Lina
Link: https://lore.kernel.org/r/20250423145047.3098-1-sven@svenpeter.dev
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://github.com/sophgo/linux into arm/fixes
RISC-V Sophgo Devicetree fixes for v6.15-rc1
Just one minor fix to correct DMA data-width
configuration for CV18xx.
Signed-off-by: Chen Wang <unicorn_wang@outlook.com>
* tag 'riscv-sophgo-dt-fixes-for-v6.15-rc1' of https://github.com/sophgo/linux:
riscv: dts: sophgo: fix DMA data-width configuration for CV18xx
Link: https://lore.kernel.org/r/MA0P287MB2262454C19B8899BC1694D04FE832@MA0P287MB2262.INDP287.PROD.OUTLOOK.COM
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux into arm/fixes
Amlogic Fixes for v6.15:
- fix reference to unknown/untested PWM clock on ARM/ARM64 boards
- fix missing clkc_audio node on dreambox ARM64 DT
* tag 'amlogic-fixes-for-v6.15' of https://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux:
arm64: dts: amlogic: dreambox: fix missing clkc_audio node
arm64: dts: amlogic: g12: fix reference to unknown/untested PWM clock
arm64: dts: amlogic: gx: fix reference to unknown/untested PWM clock
ARM: dts: amlogic: meson8b: fix reference to unknown/untested PWM clock
ARM: dts: amlogic: meson8: fix reference to unknown/untested PWM clock
Link: https://lore.kernel.org/r/e9c520a1-b986-49e1-b9b1-67511c187716@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/fixes
Removal of operating-points above what the rk3588j soc is rated for, and
a number of smaller fixes: Turing RK1 fan can spin down again, fixed pins,
pinmuxing and clocks and some devicetree-correctnes improvements.
* tag 'v6.15-rockchip-dtsfixes1' of https://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: fix Sige5 RTC interrupt pin
arm64: dts: rockchip: Assign RT5616 MCLK rate on rk3588-friendlyelec-cm3588
arm64: dts: rockchip: Align wifi node name with bindings in CB2
arm64: dts: rockchip: Fix mmc-pwrseq clock name on rock-pi-4
arm64: dts: rockchip: Use "regulator-fixed" for btreg on px30-engicam for vcc3v3-btreg
arm64: dts: rockchip: Add pinmuxing for eMMC on QNAP TS433
arm64: dts: rockchip: Remove overdrive-mode OPPs from RK3588J SoC dtsi
arm64: dts: rockchip: Allow Turing RK1 cooling fan to spin down
Link: https://lore.kernel.org/r/2923598.88bMQJbFj6@diego
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
tl;dr: There is a window in the mm switching code where the new CR3 is
set and the CPU should be getting TLB flushes for the new mm. But
should_flush_tlb() has a bug and suppresses the flush. Fix it by
widening the window where should_flush_tlb() sends an IPI.
Long Version:
=== History ===
There were a few things leading up to this.
First, updating mm_cpumask() was observed to be too expensive, so it was
made lazier. But being lazy caused too many unnecessary IPIs to CPUs
due to the now-lazy mm_cpumask(). So code was added to cull
mm_cpumask() periodically[2]. But that culling was a bit too aggressive
and skipped sending TLB flushes to CPUs that need them. So here we are
again.
=== Problem ===
The too-aggressive code in should_flush_tlb() strikes in this window:
// Turn on IPIs for this CPU/mm combination, but only
// if should_flush_tlb() agrees:
cpumask_set_cpu(cpu, mm_cpumask(next));
next_tlb_gen = atomic64_read(&next->context.tlb_gen);
choose_new_asid(next, next_tlb_gen, &new_asid, &need_flush);
load_new_mm_cr3(need_flush);
// ^ After 'need_flush' is set to false, IPIs *MUST*
// be sent to this CPU and not be ignored.
this_cpu_write(cpu_tlbstate.loaded_mm, next);
// ^ Not until this point does should_flush_tlb()
// become true!
should_flush_tlb() will suppress TLB flushes between load_new_mm_cr3()
and writing to 'loaded_mm', which is a window where they should not be
suppressed. Whoops.
=== Solution ===
Thankfully, the fuzzy "just about to write CR3" window is already marked
with loaded_mm==LOADED_MM_SWITCHING. Simply checking for that state in
should_flush_tlb() is sufficient to ensure that the CPU is targeted with
an IPI.
This will cause more TLB flush IPIs. But the window is relatively small
and I do not expect this to cause any kind of measurable performance
impact.
Update the comment where LOADED_MM_SWITCHING is written since it grew
yet another user.
Peter Z also raised a concern that should_flush_tlb() might not observe
'loaded_mm' and 'is_lazy' in the same order that switch_mm_irqs_off()
writes them. Add a barrier to ensure that they are observed in the
order they are written.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Acked-by: Rik van Riel <riel@surriel.com>
Link: https://lore.kernel.org/oe-lkp/202411282207.6bd28eae-lkp@intel.com/ [1]
Fixes: 6db2526c1d69 ("x86/mm/tlb: Only trim the mm_cpumask once a second") [2]
Reported-by: Stephen Dolan <sdolan@janestreet.com>
Cc: stable@vger.kernel.org
Acked-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix SD card timeout issue caused by LDO5 regulator getting disabled
after boot.
The kernel log shows LDO5 being disabled, which leads to a timeout
on USDHC2:
[ 33.760561] LDO5: disabling
[ 81.119861] mmc1: Timeout waiting for hardware interrupt.
To prevent this, set regulator-boot-on and regulator-always-on for
LDO5. Also add the vqmmc regulator to properly support 1.8V/3.3V
signaling for USDHC2 using a GPIO-controlled regulator.
Fixes: 6c2a1f4f71258 ("arm64: dts: imx8mp-var-som-symphony: Add Variscite Symphony board and VAR-SOM-MX8MP SoM")
Signed-off-by: Himanshu Bhavani <himanshu.bhavani@siliconsignals.io>
Acked-by: Tarang Raval <tarang.raval@siliconsignals.io>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Our QA team reported a 10%-23%, throughput reduction on an io_uring
sqpoll testcase doing IO to a null_blk, that I traced back to a
reduction of the device submission queue depth utilization. It turns out
that, after commit af5d68f8892f ("io_uring/sqpoll: manage task_work
privately"), we capped the number of task_work entries that can be
completed from a single spin of sqpoll to only 8 entries, before the
sqpoll goes around to (potentially) sleep. While this cap doesn't drive
the submission side directly, it impacts the completion behavior, which
affects the number of IO queued by fio per sqpoll cycle on the
submission side, and io_uring ends up seeing less ios per sqpoll cycle.
As a result, block layer plugging is less effective, and we see more
time spent inside the block layer in profilings charts, and increased
submission latency measured by fio.
There are other places that have increased overhead once sqpoll sleeps
more often, such as the sqpoll utilization calculation. But, in this
microbenchmark, those were not representative enough in perf charts, and
their removal didn't yield measurable changes in throughput. The major
overhead comes from the fact we plug less, and less often, when submitting
to the block layer.
My benchmark is:
fio --ioengine=io_uring --direct=1 --iodepth=128 --runtime=300 --bs=4k \
--invalidate=1 --time_based --ramp_time=10 --group_reporting=1 \
--filename=/dev/nullb0 --name=RandomReads-direct-nullb-sqpoll-4k-1 \
--rw=randread --numjobs=1 --sqthread_poll
In one machine, tested on top of Linux 6.15-rc1, we have the following
baseline:
READ: bw=4994MiB/s (5236MB/s), 4994MiB/s-4994MiB/s (5236MB/s-5236MB/s), io=439GiB (471GB), run=90001-90001msec
With this patch:
READ: bw=5762MiB/s (6042MB/s), 5762MiB/s-5762MiB/s (6042MB/s-6042MB/s), io=506GiB (544GB), run=90001-90001msec
which is a 15% improvement in measured bandwidth. The average
submission latency is noticeably lowered too. As measured by
fio:
Baseline:
lat (usec): min=20, max=241, avg=99.81, stdev=3.38
Patched:
lat (usec): min=26, max=226, avg=86.48, stdev=4.82
If we look at blktrace, we can also see the plugging behavior is
improved. In the baseline, we end up limited to plugging 8 requests in
the block layer regardless of the device queue depth size, while after
patching we can drive more io, and we manage to utilize the full device
queue.
In the baseline, after a stabilization phase, an ordinary submission
looks like:
254,0 1 49942 0.016028795 5977 U N [iou-sqp-5976] 7
After patching, I see consistently more requests per unplug.
254,0 1 4996 0.001432872 3145 U N [iou-sqp-3144] 32
Ideally, the cap size would at least be the deep enough to fill the
device queue, but we can't predict that behavior, or assume all IO goes
to a single device, and thus can't guess the ideal batch size. We also
don't want to let the tw run unbounded, though I'm not sure it would
really be a problem. Instead, let's just give it a more sensible value
that will allow for more efficient batching. I've tested with different
cap values, and initially proposed to increase the cap to 1024. Jens
argued it is too big of a bump and I observed that, with 32, I'm no
longer able to observe this bottleneck in any of my machines.
Fixes: af5d68f8892f ("io_uring/sqpoll: manage task_work privately")
Signed-off-by: Gabriel Krisman Bertazi <krisman@suse.de>
Link: https://lore.kernel.org/r/20250508181203.3785544-1-krisman@suse.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
This value is never read, so it's not needed. Remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250508121306.1277801-16-miriam.rachel.korenblit@intel.com
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
|
|
There are a number of MAC parameters that are in the iwl_cfg
(which is the last config matched to the MAC/RF combination).
This isn't necessary, there are many more of those than MACs,
so move (most of) the data into the MAC family config struct.
Note that DCCM information remains for use by older devices,
and on 9000 series it'll be in struct iwl_cfg but be ignored
when the CRF is in a Qu/So platform.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250508121306.1277801-15-miriam.rachel.korenblit@intel.com
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
|
|
This is only used with old-style debug dump, which isn't
supported on newer devices, so remove the data.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250508121306.1277801-14-miriam.rachel.korenblit@intel.com
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
|
|
Since 22000 series, the data is read by the firmware and the
driver doesn't need to know, remove the useless setting.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250508121306.1277801-13-miriam.rachel.korenblit@intel.com
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
|
|
These are (going to be) base MAC parameters that are identical
even for different platforms with the same MAC, so rename the
structure accordingly, calling it iwl_family_base_params.
Also rename the pointer to it so the dereferencing is a bit
shorter.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250508121306.1277801-12-miriam.rachel.korenblit@intel.com
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
|
|
This field is always set for >= 9000 series, but then we
already check that, so it's not needed. Remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250508121306.1277801-11-miriam.rachel.korenblit@intel.com
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
|
|
This field is unused, remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250508121306.1277801-10-miriam.rachel.korenblit@intel.com
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
|
|
Since 9000 series devices, the devices are split into MAC and
CRF parts. Currently, "struct iwl_cfg" reflects some MAC and
some RF parameters, but we want to clean this up and move the
MAC data to what's now "struct iwl_cfg_trans_params". As the
first step, to reflect the intent, rename this structure.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250508121306.1277801-9-miriam.rachel.korenblit@intel.com
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
|
|
There's no need to pass various different pointers when
the transport is already established, so just pass that
instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250508121306.1277801-8-miriam.rachel.korenblit@intel.com
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
|
|
This value hasn't been used since unified firmware in 22000
series, so there's no need to set the value for that or
newer devices. Remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250508121306.1277801-7-miriam.rachel.korenblit@intel.com
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
|
|
Instead of using fw_name_pre, handle the cc firmware file
name specially in iwl_drv_get_fwname_pre() for the cc MAC
type.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250508121306.1277801-6-miriam.rachel.korenblit@intel.com
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
|
|
Add support for the TY MAC (discrete device) and GF4 RF to
the list of MAC/RF types, and use that to remove fw_name_pre
for the ax210 family devices.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250508121306.1277801-5-miriam.rachel.korenblit@intel.com
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
|
|
This is never used, so remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250508121306.1277801-4-miriam.rachel.korenblit@intel.com
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
|
|
Since JF RF always uses b0 step and QuZ MAC always uses
a0 step for firmware, there's no need for these configs
that just force the steps to those values. Remove them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250508121306.1277801-3-miriam.rachel.korenblit@intel.com
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
|
|
This is more maintainable than the fw_name_pre prefix, and
requires fewer duplicate structs as well. Since only b0 FW
exists, override the MAC/RF steps for these devices.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250508121306.1277801-2-miriam.rachel.korenblit@intel.com
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
|
|
This is needed, otherwise we don't know what to do and will
not find the correct firmware.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250506194102.3407967-16-miriam.rachel.korenblit@intel.com
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
|
|
These are test chips, not available to users, and not even listed
in the PCI IDs table (so the driver won't bind them). There's no
reason to list specific devices with them in the driver.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250506194102.3407967-15-miriam.rachel.korenblit@intel.com
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
|
|
With just a handful of values in two bytes, the params are
smaller than the pointer to them. Inline them and save some
space.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250506194102.3407967-14-miriam.rachel.korenblit@intel.com
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
|
|
Since there's no HT on 6 GHz, only HE, the HT capabilities
are never initialized, and so the ht40_bands value is never
checked for the 6 GHz band. Remove the misleading value.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250506194102.3407967-13-miriam.rachel.korenblit@intel.com
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
|
|
The driver must not hold the wiphy mutex when unregistering the thermal
devices. Do not hold the lock for the call to iwl_mld_thermal_exit and
only do a lock/unlock to cancel the ct_kill_exit_wk work.
The problem is that iwl_mld_tzone_get_temp needs to take the wiphy lock
while the thermal code is holding its own locks already. When
unregistering the device, the reverse would happen as the driver was
calling thermal_cooling_device_unregister with the wiphy mutex already
held.
It is not likely to trigger this deadlock as it can only happen if the
thermal code is polling the temperature while the driver is being
unloaded. However, lockdep reported it so fix it.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250506194102.3407967-12-miriam.rachel.korenblit@intel.com
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
|
|
rx_omi::finished_work is initialized when the containing link is.
If the worker was queued and then an error happened, we will get to
iwl_mld_init_link from the reconfig and initialize the work after it was
queued.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250506194102.3407967-11-miriam.rachel.korenblit@intel.com
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
|
|
Different hardware has a different maximum power consumption and the
BIOS can also define a power limit for the device. Add code to select
an appropriate maximum power budget for the device and configure that
instead of using a hardcoded table.
This removes the old table. It does not work with the variable upper
limit and the there should be no consumer that requires these exact step
values.
This considerably increases the power budget for some devices and can
prevent throttling in high traffic situations.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Link: https://patch.msgid.link/20250506194102.3407967-10-miriam.rachel.korenblit@intel.com
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
|
|
Different hardware has a different maximum power consumption and the
BIOS can also define a power limit for the device. Add code to select
an appropriate maximum power budget for the device and configure that
instead of using a hardcoded table.
This removes the old table. It does not work with the variable upper
limit and the there should be no consumer that requires these exact step
values.
This considerably increases the power budget for some devices and can
prevent throttling in high traffic situations.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Link: https://patch.msgid.link/20250506194102.3407967-9-miriam.rachel.korenblit@intel.com
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
|
|
The compare_temps function in both mvm and mld dropped the const
qualifier in a cast in a way that makes -Werror=cast-qual unhappy. Add
the const to the cast to fix this.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Link: https://patch.msgid.link/20250506194102.3407967-8-miriam.rachel.korenblit@intel.com
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
|
|
This function is not implemented nor called. Remove its declaration.
Link: https://patch.msgid.link/20250506194102.3407967-7-miriam.rachel.korenblit@intel.com
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
|
|
Add support for a new version of link configuration command
which includes NPCA and high priority TX traffic support for wifi8.
Signed-off-by: Yedidya Benshimol <yedidya.ben.shimol@intel.com>
Link: https://patch.msgid.link/20250506194102.3407967-6-miriam.rachel.korenblit@intel.com
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
|
|
Add a new version of mac configuration command
which includes UHR support indication.
Signed-off-by: Yedidya Benshimol <yedidya.ben.shimol@intel.com>
Link: https://patch.msgid.link/20250506194102.3407967-5-miriam.rachel.korenblit@intel.com
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
|
|
Add a new version of sta configuration command
which includes these wifi8 features:
1. LDPC X2 CW size support indication
2. Indication if ICF frame is needed instead of RTS
3. support for MIC padding delays for protected control frames
Signed-off-by: Yedidya Benshimol <yedidya.ben.shimol@intel.com>
Link: https://patch.msgid.link/20250506194102.3407967-4-miriam.rachel.korenblit@intel.com
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
|
|
Range response version 10 removes the rx and tx rates fields.
These fields aren't used by the driver anyway, so no change is
needed to support it.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Link: https://patch.msgid.link/20250506194102.3407967-3-miriam.rachel.korenblit@intel.com
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
|
|
Since the FW is the one to assign an ID to a BA, it can happen that
the FW sends a bar_frame_release_notif before the driver had the chance to
allocate the BAID.
Convert the IWL_FW_CHECK into a regular debug print.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250506194102.3407967-2-miriam.rachel.korenblit@intel.com
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
|
|
Cong Wang says:
====================
net_sched: Fix gso_skb flushing during qdisc change
This patchset contains a bug fix and its test cases, please check each
patch description for more details. To keep the bug fix minimum, I
intentionally limit the code changes to the cases reported here.
---
v2: added a missing qlen--
fixed the new boolean parameter for two qdiscs
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Added new test cases for FQ, FQ_CODEL, FQ_PIE, and HHF qdiscs to verify queue
trimming behavior when the qdisc limit is dynamically reduced.
Each test injects packets, reduces the qdisc limit, and checks that the new
limit is enforced. This is still best effort since timing qdisc backlog
is not easy.
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previously, when reducing a qdisc's limit via the ->change() operation, only
the main skb queue was trimmed, potentially leaving packets in the gso_skb
list. This could result in NULL pointer dereference when we only check
sch->limit against sch->q.qlen.
This patch introduces a new helper, qdisc_dequeue_internal(), which ensures
both the gso_skb list and the main queue are properly flushed when trimming
excess packets. All relevant qdiscs (codel, fq, fq_codel, fq_pie, hhf, pie)
are updated to use this helper in their ->change() routines.
Fixes: 76e3cc126bb2 ("codel: Controlled Delay AQM")
Fixes: 4b549a2ef4be ("fq_codel: Fair Queue Codel AQM")
Fixes: afe4fd062416 ("pkt_sched: fq: Fair Queue packet scheduler")
Fixes: ec97ecf1ebe4 ("net: sched: add Flow Queue PIE packet scheduler")
Fixes: 10239edf86f1 ("net-qdisc-hhf: Heavy-Hitter Filter (HHF) qdisc")
Fixes: d4b36210c2e6 ("net: pkt_sched: PIE AQM scheme")
Reported-by: Will <willsroot@protonmail.com>
Reported-by: Savy <savy@syst3mfailure.io>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mark_buffer_write_io_error sets sb->s_wb_err to -EIO twice.
Once in mapping_set_error and once in errseq_set.
Only mapping_set_error checks if bh->b_assoc_map->host is NULL.
Discovered during null pointer dereference during writeback
to a failing device:
[<ffffffff9a416dc8>] ? mark_buffer_write_io_error+0x98/0xc0
[<ffffffff9a416dbe>] ? mark_buffer_write_io_error+0x8e/0xc0
[<ffffffff9ad4bda0>] end_buffer_async_write+0x90/0xd0
[<ffffffff9ad4e3eb>] end_bio_bh_io_sync+0x2b/0x40
[<ffffffff9adbafe6>] blk_update_request+0x1b6/0x480
[<ffffffff9adbb3d8>] blk_mq_end_request+0x18/0x30
[<ffffffff9adbc6aa>] blk_mq_dispatch_rq_list+0x4da/0x8e0
[<ffffffff9adc0a68>] __blk_mq_sched_dispatch_requests+0x218/0x6a0
[<ffffffff9adc07fa>] blk_mq_sched_dispatch_requests+0x3a/0x80
[<ffffffff9adbbb98>] blk_mq_run_hw_queue+0x108/0x330
[<ffffffff9adbcf58>] blk_mq_flush_plug_list+0x178/0x5f0
[<ffffffff9adb6741>] __blk_flush_plug+0x41/0x120
[<ffffffff9adb6852>] blk_finish_plug+0x22/0x40
[<ffffffff9ad47cb0>] wb_writeback+0x150/0x280
[<ffffffff9ac5343f>] ? set_worker_desc+0x9f/0xc0
[<ffffffff9ad4676e>] wb_workfn+0x24e/0x4a0
Fixes: 485e9605c0573 ("fs/buffer.c: record blockdev write errors in super_block that it backs")
Signed-off-by: Jeremy Bongio <jbongio@google.com>
Link: https://lore.kernel.org/20250507123010.1228243-1-jbongio@google.com
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
When running in nominal drive mode, the maximum allowed frequency for
the NoC is 800MHz, but the OPP table for the i.MX8MP interconnect device
listed the 1GHz operating point for the NoC, regardless of the active
mode.
The newly introduced imx8mp-nominal.dtsi header reconfigures the clock
controller to observe nominal drive mode limits, so have it modify the
maximum NoC OPP as well.
Fixes: 255fbd9eabe7 ("arm64: dts: imx8mp: Add optional nominal drive mode DTSI")
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The partial matching of DAI widget to link names, can cause problems if
one of the widget names is a substring of another. E.g. with names
"Foo1" and Foo10", it's not possible to correctly link up "Foo1".
Modify the logic so that if multiple DAI links match the widget stream
name, prioritize a full match if one is found.
Fixes: fe88788779fc ("ASoC: SOF: topology: Use partial match for connecting DAI link and DAI widget")
Link: https://github.com/thesofproject/linux/issues/5308
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://patch.msgid.link/20250509085318.13936-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Keep using the PIO mode for commands on ACE2+ platforms, similarly how
the legacy stack is configured.
Fixes: 05cf17f1bf6d ("ASoC: SOF: Intel: hda-bus: Use PIO mode for Lunar Lake")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20250509081308.13784-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The firmware does not provide any information for capture streams via the
shared pipeline registers.
To avoid reporting invalid delay value for capture streams to user space
we need to disable it.
Fixes: af74dbd0dbcf ("ASoC: SOF: ipc4-pcm: allocate time info for pcm delay feature")
Cc: stable@vger.kernel.org
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Link: https://patch.msgid.link/20250509085951.15696-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The header.numid is set to scontrol->comp_id in bytes_ext_get and it is
ignored during bytes_ext_put.
The use of comp_id is not quite great as it is kernel internal
identification number.
Set the header.numid to SOF_CTRL_CMD_BINARY during get and validate the
numid during put to provide consistent and compatible identification
number as IPC3.
For IPC4 existing tooling also ignored the numid but with the use of
SOF_CTRL_CMD_BINARY the different handling of the blobs can be dropped,
providing better user experience.
Reported-by: Seppo Ingalsuo <seppo.ingalsuo@linux.intel.com>
Closes: https://github.com/thesofproject/linux/issues/5282
Fixes: a062c8899fed ("ASoC: SOF: ipc4-control: Add support for bytes control get and put")
Cc: stable@vger.kernel.org
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Seppo Ingalsuo <seppo.ingalsuo@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Link: https://patch.msgid.link/20250509085633.14930-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Determining the SST/MST mode during state computation must be done based
on the output type stored in the CRTC state, which in turn is set once
based on the modeset connector's SST vs. MST type and will not change as
long as the connector is using the CRTC. OTOH the MST mode indicated by
the given connector's intel_dp::is_mst flag can change independently of
the above output type, based on what sink is at any moment plugged to
the connector.
Fix the state computation accordingly.
Cc: Jani Nikula <jani.nikula@intel.com>
Fixes: f6971d7427c2 ("drm/i915/mst: adapt intel_dp_mtp_tu_compute_config() for 128b/132b SST")
Closes: https://gitlab.freedesktop.org/drm/xe/kernel/-/issues/4607
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://lore.kernel.org/r/20250507151953.251846-1-imre.deak@intel.com
(cherry picked from commit 0f45696ddb2b901fbf15cb8d2e89767be481d59f)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
When increasing the array size in memblock_double_array() and the slab
is not yet available, a call to memblock_find_in_range() is used to
reserve/allocate memory. However, the range returned may not have been
accepted, which can result in a crash when booting an SNP guest:
RIP: 0010:memcpy_orig+0x68/0x130
Code: ...
RSP: 0000:ffffffff9cc03ce8 EFLAGS: 00010006
RAX: ff11001ff83e5000 RBX: 0000000000000000 RCX: fffffffffffff000
RDX: 0000000000000bc0 RSI: ffffffff9dba8860 RDI: ff11001ff83e5c00
RBP: 0000000000002000 R08: 0000000000000000 R09: 0000000000002000
R10: 000000207fffe000 R11: 0000040000000000 R12: ffffffff9d06ef78
R13: ff11001ff83e5000 R14: ffffffff9dba7c60 R15: 0000000000000c00
memblock_double_array+0xff/0x310
memblock_add_range+0x1fb/0x2f0
memblock_reserve+0x4f/0xa0
memblock_alloc_range_nid+0xac/0x130
memblock_alloc_internal+0x53/0xc0
memblock_alloc_try_nid+0x3d/0xa0
swiotlb_init_remap+0x149/0x2f0
mem_init+0xb/0xb0
mm_core_init+0x8f/0x350
start_kernel+0x17e/0x5d0
x86_64_start_reservations+0x14/0x30
x86_64_start_kernel+0x92/0xa0
secondary_startup_64_no_verify+0x194/0x19b
Mitigate this by calling accept_memory() on the memory range returned
before the slab is available.
Prior to v6.12, the accept_memory() interface used a 'start' and 'end'
parameter instead of 'start' and 'size', therefore the accept_memory()
call must be adjusted to specify 'start + size' for 'end' when applying
to kernels prior to v6.12.
Cc: stable@vger.kernel.org # see patch description, needs adjustments for <= 6.11
Fixes: dcdfdd40fa82 ("mm: Add support for unaccepted memory")
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Link: https://lore.kernel.org/r/da1ac73bf4ded761e21b4e4bb5178382a580cd73.1746725050.git.thomas.lendacky@amd.com
Signed-off-by: Mike Rapoport (Microsoft) <rppt@kernel.org>
|
|
Wei Fang says:
====================
Add more features for ENETC v4 - round 2
This patch set adds the following features.
1. Compared with ENETC v1, the formats of tables and command BD of ENETC
v4 have changed significantly, and the two are not compatible. Therefore,
in order to support the NETC Table Management Protocol (NTMP) v2.0, we
introduced the netc-lib driver and added support for MAC address filter
table and RSS table.
2. Add MAC filter and VLAN filter support for i.MX95 ENETC PF.
3. Add RSS support for i.MX95 ENETC PF.
4. Add loopback support for i.MX95 ENETC PF.
v1: Link: https://lore.kernel.org/20250103060610.2233908-1-wei.fang@nxp.com/
v2: Link: https://lore.kernel.org/20250113082245.2332775-1-wei.fang@nxp.com/
v3: Link: https://lore.kernel.org/20250304072201.1332603-1-wei.fang@nxp.com/
v4: Link: https://lore.kernel.org/20250311053830.1516523-1-wei.fang@nxp.com/
v5: Link: https://lore.kernel.org/20250411095752.3072696-1-wei.fang@nxp.com/
v6: Link: https://lore.kernel.org/20250428105657.3283130-1-wei.fang@nxp.com/
====================
Link: https://patch.msgid.link/20250506080735.3444381-1-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add internal loopback support for i.MX95 ENETC PF, the default loopback
mode is MAC level loopback, the MAC Tx data is looped back onto the Rx.
The MAC interface runs at a fixed 1:8 ratio of NETC clock in MAC-level
loopback mode, with no dependency on Tx clock.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20250506080735.3444381-15-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
