| Age | Commit message (Collapse) | Author |
|---|
|
Chip outputs are enabled[1] before actual reset is performed[2] which might
cause pin output value to flip flop if previous pin value was set to 1.
Fix that behavior by making sure chip is fully reset before all outputs are
enabled.
Flip-flop can be noticed when module is removed and inserted again and one of
the pins was changed to 1 before removal. 100 microsecond flipping is
noticeable on oscilloscope (100khz SPI bus).
For a properly reset chip - output is enabled around 100 microseconds (on 100khz
SPI bus) later during probing process hence should be irrelevant behavioral
change.
Fixes: 7ebc194d0fd4 (gpio: 74x164: Introduce 'enable-gpios' property)
Link: https://elixir.bootlin.com/linux/v6.7.4/source/drivers/gpio/gpio-74x164.c#L130 [1]
Link: https://elixir.bootlin.com/linux/v6.7.4/source/drivers/gpio/gpio-74x164.c#L150 [2]
Signed-off-by: Arturas Moskvinas <arturas.moskvinas@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
From: Yu Kuai <yukuai3@huawei.com>
Co-developed-by: Paul Luse <paul.e.luse@linux.intel.com>
The original idea is that Paul want to optimize raid1 read
performance([1]), however, we think that the original code for
read_balance() is quite complex, and we don't want to add more
complexity. Hence we decide to refactor read_balance() first, to make
code cleaner and easier for follow up.
Before this patchset, read_balance() has many local variables and many
branches, it want to consider all the scenarios in one iteration. The
idea of this patch is to divide them into 4 different steps:
1) If resync is in progress, find the first usable disk, patch 5;
Otherwise:
2) Loop through all disks and skipping slow disks and disks with bad
blocks, choose the best disk, patch 10. If no disk is found:
3) Look for disks with bad blocks and choose the one with most number of
sectors, patch 8. If no disk is found:
4) Choose first found slow disk with no bad blocks, or slow disk with
most number of sectors, patch 7.
Note that step 3) and step 4) are super code path, and performance
should not be considered.
And after this patchset, we'll continue to optimize read_balance for
step 2), specifically how to choose the best rdev to read.
[1] https://lore.kernel.org/all/20240102125115.129261-1-paul.e.luse@linux.intel.com/
Yu Kuai (11):
md: add a new helper rdev_has_badblock()
md/raid1: factor out helpers to add rdev to conf
md/raid1: record nonrot rdevs while adding/removing rdevs to conf
md/raid1: fix choose next idle in read_balance()
md/raid1-10: add a helper raid1_check_read_range()
md/raid1-10: factor out a new helper raid1_should_read_first()
md/raid1: factor out read_first_rdev() from read_balance()
md/raid1: factor out choose_slow_rdev() from read_balance()
md/raid1: factor out choose_bb_rdev() from read_balance()
md/raid1: factor out the code to manage sequential IO
md/raid1: factor out helpers to choose the best rdev from
read_balance()
|
|
The way that best rdev is chosen:
1) If the read is sequential from one rdev:
- if rdev is rotational, use this rdev;
- if rdev is non-rotational, use this rdev until total read length
exceed disk opt io size;
2) If the read is not sequential:
- if there is idle disk, use it, otherwise:
- if the array has non-rotational disk, choose the rdev with minimal
inflight IO;
- if all the underlaying disks are rotational disk, choose the rdev
with closest IO;
There are no functional changes, just to make code cleaner and prepare
for following refactor.
Co-developed-by: Paul Luse <paul.e.luse@linux.intel.com>
Signed-off-by: Paul Luse <paul.e.luse@linux.intel.com>
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Reviewed-by: Xiao Ni <xni@redhat.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20240229095714.926789-12-yukuai1@huaweicloud.com
|
|
There is no functional change for now, make read_balance() cleaner and
prepare to fix problems and refactor the handler of sequential IO.
Co-developed-by: Paul Luse <paul.e.luse@linux.intel.com>
Signed-off-by: Paul Luse <paul.e.luse@linux.intel.com>
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Reviewed-by: Xiao Ni <xni@redhat.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20240229095714.926789-11-yukuai1@huaweicloud.com
|
|
read_balance() is hard to understand because there are too many status
and branches, and it's overlong.
This patch factor out the case to read the rdev with bad blocks from
read_balance(), there are no functional changes.
Co-developed-by: Paul Luse <paul.e.luse@linux.intel.com>
Signed-off-by: Paul Luse <paul.e.luse@linux.intel.com>
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Reviewed-by: Xiao Ni <xni@redhat.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20240229095714.926789-10-yukuai1@huaweicloud.com
|
|
read_balance() is hard to understand because there are too many status
and branches, and it's overlong.
This patch factor out the case to read the slow rdev from
read_balance(), there are no functional changes.
Co-developed-by: Paul Luse <paul.e.luse@linux.intel.com>
Signed-off-by: Paul Luse <paul.e.luse@linux.intel.com>
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Reviewed-by: Xiao Ni <xni@redhat.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20240229095714.926789-9-yukuai1@huaweicloud.com
|
|
read_balance() is hard to understand because there are too many status
and branches, and it's overlong.
This patch factor out the case to read the first rdev from
read_balance(), there are no functional changes.
Co-developed-by: Paul Luse <paul.e.luse@linux.intel.com>
Signed-off-by: Paul Luse <paul.e.luse@linux.intel.com>
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Reviewed-by: Xiao Ni <xni@redhat.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20240229095714.926789-8-yukuai1@huaweicloud.com
|
|
If resync is in progress, read_balance() should find the first usable
disk, otherwise, data could be inconsistent after resync is done. raid1
and raid10 implement the same checking, hence factor out the checking
to make code cleaner.
Noted that raid1 is using 'mddev->recovery_cp', which is updated after
all resync IO is done, while raid10 is using 'conf->next_resync', which
is inaccurate because raid10 update it before submitting resync IO.
Fortunately, raid10 read IO can't concurrent with resync IO, hence there
is no problem. And this patch also switch raid10 to use
'mddev->recovery_cp'.
Co-developed-by: Paul Luse <paul.e.luse@linux.intel.com>
Signed-off-by: Paul Luse <paul.e.luse@linux.intel.com>
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Reviewed-by: Xiao Ni <xni@redhat.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20240229095714.926789-7-yukuai1@huaweicloud.com
|
|
The checking and handler of bad blocks appear many timers during
read_balance() in raid1 and raid10. This helper will be used in later
patches to simplify read_balance() a lot.
Co-developed-by: Paul Luse <paul.e.luse@linux.intel.com>
Signed-off-by: Paul Luse <paul.e.luse@linux.intel.com>
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Reviewed-by: Xiao Ni <xni@redhat.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20240229095714.926789-6-yukuai1@huaweicloud.com
|
|
Commit 12cee5a8a29e ("md/raid1: prevent merging too large request") add
the case choose next idle in read_balance():
read_balance:
for_each_rdev
if(next_seq_sect == this_sector || dist == 0)
-> sequential reads
best_disk = disk;
if (...)
choose_next_idle = 1
continue;
for_each_rdev
-> iterate next rdev
if (pending == 0)
best_disk = disk;
-> choose the next idle disk
break;
if (choose_next_idle)
-> keep using this rdev if there are no other idle disk
contine
However, commit 2e52d449bcec ("md/raid1: add failfast handling for reads.")
remove the code:
- /* If device is idle, use it */
- if (pending == 0) {
- best_disk = disk;
- break;
- }
Hence choose next idle will never work now, fix this problem by
following:
1) don't set best_disk in this case, read_balance() will choose the best
disk after iterating all the disks;
2) add 'pending' so that other idle disk will be chosen;
3) add a new local variable 'sequential_disk' to record the disk, and if
there is no other idle disk, 'sequential_disk' will be chosen;
Fixes: 2e52d449bcec ("md/raid1: add failfast handling for reads.")
Co-developed-by: Paul Luse <paul.e.luse@linux.intel.com>
Signed-off-by: Paul Luse <paul.e.luse@linux.intel.com>
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Reviewed-by: Xiao Ni <xni@redhat.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20240229095714.926789-5-yukuai1@huaweicloud.com
|
|
For raid1, each read will iterate all the rdevs from conf and check if
any rdev is non-rotational, then choose rdev with minimal IO inflight
if so, or rdev with closest distance otherwise.
Disk nonrot info can be changed through sysfs entry:
/sys/block/[disk_name]/queue/rotational
However, consider that this should only be used for testing, and user
really shouldn't do this in real life. Record the number of non-rotational
disks in conf, to avoid checking each rdev in IO fast path and simplify
read_balance() a little bit.
Co-developed-by: Paul Luse <paul.e.luse@linux.intel.com>
Signed-off-by: Paul Luse <paul.e.luse@linux.intel.com>
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20240229095714.926789-4-yukuai1@huaweicloud.com
|
|
There are no functional changes, just make code cleaner and prepare to
record disk non-rotational information while adding and removing rdev to
conf
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20240229095714.926789-3-yukuai1@huaweicloud.com
|
|
The current api is_badblock() must pass in 'first_bad' and
'bad_sectors', however, many caller just want to know if there are
badblocks or not, and these caller must define two local variable that
will never be used.
Add a new helper rdev_has_badblock() that will only return if there are
badblocks or not, remove unnecessary local variables and replace
is_badblock() with the new helper in many places.
There are no functional changes, and the new helper will also be used
later to refactor read_balance().
Co-developed-by: Paul Luse <paul.e.luse@linux.intel.com>
Signed-off-by: Paul Luse <paul.e.luse@linux.intel.com>
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Reviewed-by: Xiao Ni <xni@redhat.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20240229095714.926789-2-yukuai1@huaweicloud.com
|
|
Nouveau deallocates a few buffers post GPU init which are required for GPU suspend/resume to function correctly.
This is likely not as big an issue on systems where the NVGPU is the only GPU, but on multi-GPU set ups it leads to a regression where the kernel module errors and results in a system-wide rendering freeze.
This commit addresses that regression by moving the two buffers required for suspend and resume to be deallocated at driver unload instead of post init.
Fixes: 042b5f83841fb ("drm/nouveau: fix several DMA buffer leaks")
Signed-off-by: Sid Pranjale <sidpranjale127@protonmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Turns out usage is always in bytes not shifted.
Fixes: 72fa02fdf833 ("nouveau: add an ioctl to report vram usage")
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
https://gitlab.freedesktop.org/agd5f/linux into drm-fixes
amd-drm-fixes-6.8-2024-02-29:
amdgpu:
- Fix potential buffer overflow
- Fix power min cap
- Suspend/resume fix
- SI PM fix
- eDP fix
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240229152424.6646-1-alexander.deucher@amd.com
|
|
https://gitlab.freedesktop.org/drm/msm into drm-fixes
Fixes for v6.8-rc7
DP:
- Revert a change which was causing a HDP regression
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGvhWvHiPGQ1pRD2XPAQoHEM2M35kjhrsSAEtzh8AMSRvg@mail.gmail.com
|
|
https://gitlab.freedesktop.org/drm/xe/kernel into drm-fixes
UAPI Changes:
- A couple of tracepoint updates from Priyanka and Lucas.
- Make sure BINDs are completed before accepting UNBINDs on LR vms.
- Don't arbitrarily restrict max number of batched binds.
- Add uapi for dumpable bos (agreed on IRC).
- Remove unused uapi flags and a leftover comment.
Driver Changes:
- A couple of fixes related to the execlist backend.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thomas Hellstrom <thomas.hellstrom@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ZeCBg4MA2hd1oggN@fedora
|
|
https://anongit.freedesktop.org/git/drm/drm-misc into drm-fixes
A reset fix for host1x, a resource leak fix and a probe fix for aux-hpd,
a use-after-free fix and a boot fix for a pmic_glink qcom driver in
drivers/soc, a fix for the simpledrm/tegra transition, a kunit fix for
the TTM tests, a font handling fix for fbcon, two allocation fixes and a
kunit test to cover them for drm/buddy
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <mripard@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240229-angelic-adorable-teal-fbfabb@houat
|
|
Fix to allocate fprobe::entry_data_size buffer with rethook instances.
If fprobe doesn't allocate entry_data_size buffer for each rethook instance,
fprobe entry handler can cause a buffer overrun when storing entry data in
entry handler.
Link: https://lore.kernel.org/all/170920576727.107552.638161246679734051.stgit@devnote2/
Reported-by: Jiri Olsa <olsajiri@gmail.com>
Closes: https://lore.kernel.org/all/Zd9eBn2FTQzYyg7L@krava/
Fixes: 4bbd93455659 ("kprobes: kretprobe scalability improvement")
Cc: stable@vger.kernel.org
Tested-by: Jiri Olsa <olsajiri@gmail.com>
Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
|
|
Boqun pointed out that workqueues aren't handling BH work items on offlined
CPUs. Unlike tasklet which transfers out the pending tasks from
CPUHP_SOFTIRQ_DEAD, BH workqueue would just leave them pending which is
problematic. Note that this behavior is specific to BH workqueues as the
non-BH per-CPU workers just become unbound when the CPU goes offline.
This patch fixes the issue by draining the pending BH work items from an
offlined CPU from CPUHP_SOFTIRQ_DEAD. Because work items carry more context,
it's not as easy to transfer the pending work items from one pool to
another. Instead, run BH work items which execute the offlined pools on an
online CPU.
Note that this assumes that no further BH work items will be queued on the
offlined CPUs. This assumption is shared with tasklet and should be fine for
conversions. However, this issue also exists for per-CPU workqueues which
will just keep executing work items queued after CPU offline on unbound
workers and workqueue should reject per-CPU and BH work items queued on
offline CPUs. This will be addressed separately later.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-and-reviewed-by: Boqun Feng <boqun.feng@gmail.com>
Link: http://lkml.kernel.org/r/Zdvw0HdSXcU3JZ4g@boqun-archlinux
|
|
When creating a snapshot we may do a double free of an anonymous device
in case there's an error committing the transaction. The second free may
result in freeing an anonymous device number that was allocated by some
other subsystem in the kernel or another btrfs filesystem.
The steps that lead to this:
1) At ioctl.c:create_snapshot() we allocate an anonymous device number
and assign it to pending_snapshot->anon_dev;
2) Then we call btrfs_commit_transaction() and end up at
transaction.c:create_pending_snapshot();
3) There we call btrfs_get_new_fs_root() and pass it the anonymous device
number stored in pending_snapshot->anon_dev;
4) btrfs_get_new_fs_root() frees that anonymous device number because
btrfs_lookup_fs_root() returned a root - someone else did a lookup
of the new root already, which could some task doing backref walking;
5) After that some error happens in the transaction commit path, and at
ioctl.c:create_snapshot() we jump to the 'fail' label, and after
that we free again the same anonymous device number, which in the
meanwhile may have been reallocated somewhere else, because
pending_snapshot->anon_dev still has the same value as in step 1.
Recently syzbot ran into this and reported the following trace:
------------[ cut here ]------------
ida_free called for id=51 which is not allocated.
WARNING: CPU: 1 PID: 31038 at lib/idr.c:525 ida_free+0x370/0x420 lib/idr.c:525
Modules linked in:
CPU: 1 PID: 31038 Comm: syz-executor.2 Not tainted 6.8.0-rc4-syzkaller-00410-gc02197fc9076 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/25/2024
RIP: 0010:ida_free+0x370/0x420 lib/idr.c:525
Code: 10 42 80 3c 28 (...)
RSP: 0018:ffffc90015a67300 EFLAGS: 00010246
RAX: be5130472f5dd000 RBX: 0000000000000033 RCX: 0000000000040000
RDX: ffffc90009a7a000 RSI: 000000000003ffff RDI: 0000000000040000
RBP: ffffc90015a673f0 R08: ffffffff81577992 R09: 1ffff92002b4cdb4
R10: dffffc0000000000 R11: fffff52002b4cdb5 R12: 0000000000000246
R13: dffffc0000000000 R14: ffffffff8e256b80 R15: 0000000000000246
FS: 00007fca3f4b46c0(0000) GS:ffff8880b9500000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f167a17b978 CR3: 000000001ed26000 CR4: 0000000000350ef0
Call Trace:
<TASK>
btrfs_get_root_ref+0xa48/0xaf0 fs/btrfs/disk-io.c:1346
create_pending_snapshot+0xff2/0x2bc0 fs/btrfs/transaction.c:1837
create_pending_snapshots+0x195/0x1d0 fs/btrfs/transaction.c:1931
btrfs_commit_transaction+0xf1c/0x3740 fs/btrfs/transaction.c:2404
create_snapshot+0x507/0x880 fs/btrfs/ioctl.c:848
btrfs_mksubvol+0x5d0/0x750 fs/btrfs/ioctl.c:998
btrfs_mksnapshot+0xb5/0xf0 fs/btrfs/ioctl.c:1044
__btrfs_ioctl_snap_create+0x387/0x4b0 fs/btrfs/ioctl.c:1306
btrfs_ioctl_snap_create_v2+0x1ca/0x400 fs/btrfs/ioctl.c:1393
btrfs_ioctl+0xa74/0xd40
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:871 [inline]
__se_sys_ioctl+0xfe/0x170 fs/ioctl.c:857
do_syscall_64+0xfb/0x240
entry_SYSCALL_64_after_hwframe+0x6f/0x77
RIP: 0033:0x7fca3e67dda9
Code: 28 00 00 00 (...)
RSP: 002b:00007fca3f4b40c8 EFLAGS: 00000246 ORIG_RAX: 0000000000000010
RAX: ffffffffffffffda RBX: 00007fca3e7abf80 RCX: 00007fca3e67dda9
RDX: 00000000200005c0 RSI: 0000000050009417 RDI: 0000000000000003
RBP: 00007fca3e6ca47a R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
R13: 000000000000000b R14: 00007fca3e7abf80 R15: 00007fff6bf95658
</TASK>
Where we get an explicit message where we attempt to free an anonymous
device number that is not currently allocated. It happens in a different
code path from the example below, at btrfs_get_root_ref(), so this change
may not fix the case triggered by syzbot.
To fix at least the code path from the example above, change
btrfs_get_root_ref() and its callers to receive a dev_t pointer argument
for the anonymous device number, so that in case it frees the number, it
also resets it to 0, so that up in the call chain we don't attempt to do
the double free.
CC: stable@vger.kernel.org # 5.10+
Link: https://lore.kernel.org/linux-btrfs/000000000000f673a1061202f630@google.com/
Fixes: e03ee2fe873e ("btrfs: do not ASSERT() if the newly created subvolume already got read")
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
When FIEMAP_FLAG_SYNC is given to fiemap the expectation is that that
are no concurrent writes and we get a stable view of the inode's extent
layout.
When the flag is given we flush all IO (and wait for ordered extents to
complete) and then lock the inode in shared mode, however that leaves open
the possibility that a write might happen right after the flushing and
before locking the inode. So fix this by flushing again after locking the
inode - we leave the initial flushing before locking the inode to avoid
holding the lock and blocking other RO operations while waiting for IO
and ordered extents to complete. The second flushing while holding the
inode's lock will most of the time do nothing or very little since the
time window for new writes to have happened is small.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
For fiemap we recently stopped locking the target extent range for the
whole duration of the fiemap call, in order to avoid a deadlock in a
scenario where the fiemap buffer happens to be a memory mapped range of
the same file. This use case is very unlikely to be useful in practice but
it may be triggered by fuzz testing (syzbot, etc).
However by not locking the target extent range for the whole duration of
the fiemap call we can race with an ordered extent. This happens like
this:
1) The fiemap task finishes processing a file extent item that covers
the file range [512K, 1M[, and that file extent item is the last item
in the leaf currently being processed;
2) And ordered extent for the file range [768K, 2M[, in COW mode,
completes (btrfs_finish_one_ordered()) and the file extent item
covering the range [512K, 1M[ is trimmed to cover the range
[512K, 768K[ and then a new file extent item for the range [768K, 2M[
is inserted in the inode's subvolume tree;
3) The fiemap task calls fiemap_next_leaf_item(), which then calls
btrfs_next_leaf() to find the next leaf / item. This finds that the
the next key following the one we previously processed (its type is
BTRFS_EXTENT_DATA_KEY and its offset is 512K), is the key corresponding
to the new file extent item inserted by the ordered extent, which has
a type of BTRFS_EXTENT_DATA_KEY and an offset of 768K;
4) Later the fiemap code ends up at emit_fiemap_extent() and triggers
the warning:
if (cache->offset + cache->len > offset) {
WARN_ON(1);
return -EINVAL;
}
Since we get 1M > 768K, because the previously emitted entry for the
old extent covering the file range [512K, 1M[ ends at an offset that
is greater than the new extent's start offset (768K). This makes fiemap
fail with -EINVAL besides triggering the warning that produces a stack
trace like the following:
[1621.677651] ------------[ cut here ]------------
[1621.677656] WARNING: CPU: 1 PID: 204366 at fs/btrfs/extent_io.c:2492 emit_fiemap_extent+0x84/0x90 [btrfs]
[1621.677899] Modules linked in: btrfs blake2b_generic (...)
[1621.677951] CPU: 1 PID: 204366 Comm: pool Not tainted 6.8.0-rc5-btrfs-next-151+ #1
[1621.677954] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.2-0-gea1b7a073390-prebuilt.qemu.org 04/01/2014
[1621.677956] RIP: 0010:emit_fiemap_extent+0x84/0x90 [btrfs]
[1621.678033] Code: 2b 4c 89 63 (...)
[1621.678035] RSP: 0018:ffffab16089ffd20 EFLAGS: 00010206
[1621.678037] RAX: 00000000004fa000 RBX: ffffab16089ffe08 RCX: 0000000000009000
[1621.678039] RDX: 00000000004f9000 RSI: 00000000004f1000 RDI: ffffab16089ffe90
[1621.678040] RBP: 00000000004f9000 R08: 0000000000001000 R09: 0000000000000000
[1621.678041] R10: 0000000000000000 R11: 0000000000001000 R12: 0000000041d78000
[1621.678043] R13: 0000000000001000 R14: 0000000000000000 R15: ffff9434f0b17850
[1621.678044] FS: 00007fa6e20006c0(0000) GS:ffff943bdfa40000(0000) knlGS:0000000000000000
[1621.678046] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[1621.678048] CR2: 00007fa6b0801000 CR3: 000000012d404002 CR4: 0000000000370ef0
[1621.678053] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[1621.678055] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[1621.678056] Call Trace:
[1621.678074] <TASK>
[1621.678076] ? __warn+0x80/0x130
[1621.678082] ? emit_fiemap_extent+0x84/0x90 [btrfs]
[1621.678159] ? report_bug+0x1f4/0x200
[1621.678164] ? handle_bug+0x42/0x70
[1621.678167] ? exc_invalid_op+0x14/0x70
[1621.678170] ? asm_exc_invalid_op+0x16/0x20
[1621.678178] ? emit_fiemap_extent+0x84/0x90 [btrfs]
[1621.678253] extent_fiemap+0x766/0xa30 [btrfs]
[1621.678339] btrfs_fiemap+0x45/0x80 [btrfs]
[1621.678420] do_vfs_ioctl+0x1e4/0x870
[1621.678431] __x64_sys_ioctl+0x6a/0xc0
[1621.678434] do_syscall_64+0x52/0x120
[1621.678445] entry_SYSCALL_64_after_hwframe+0x6e/0x76
There's also another case where before calling btrfs_next_leaf() we are
processing a hole or a prealloc extent and we had several delalloc ranges
within that hole or prealloc extent. In that case if the ordered extents
complete before we find the next key, we may end up finding an extent item
with an offset smaller than (or equals to) the offset in cache->offset.
So fix this by changing emit_fiemap_extent() to address these three
scenarios like this:
1) For the first case, steps listed above, adjust the length of the
previously cached extent so that it does not overlap with the current
extent, emit the previous one and cache the current file extent item;
2) For the second case where he had a hole or prealloc extent with
multiple delalloc ranges inside the hole or prealloc extent's range,
and the current file extent item has an offset that matches the offset
in the fiemap cache, just discard what we have in the fiemap cache and
assign the current file extent item to the cache, since it's more up
to date;
3) For the third case where he had a hole or prealloc extent with
multiple delalloc ranges inside the hole or prealloc extent's range
and the offset of the file extent item we just found is smaller than
what we have in the cache, just skip the current file extent item
if its range end at or behind the cached extent's end, because we may
have emitted (to the fiemap user space buffer) delalloc ranges that
overlap with the current file extent item's range. If the file extent
item's range goes beyond the end offset of the cached extent, just
emit the cached extent and cache a subrange of the file extent item,
that goes from the end offset of the cached extent to the end offset
of the file extent item.
Dealing with those cases in those ways makes everything consistent by
reflecting the current state of file extent items in the btree and
without emitting extents that have overlapping ranges (which would be
confusing and violating expectations).
This issue could be triggered often with test case generic/561, and was
also hit and reported by Wang Yugui.
Reported-by: Wang Yugui <wangyugui@e16-tech.com>
Link: https://lore.kernel.org/linux-btrfs/20240223104619.701F.409509F4@e16-tech.com/
Fixes: b0ad381fa769 ("btrfs: fix deadlock with fiemap and extent locking")
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
This is the next upgrade to the Rust toolchain, from 1.75.0 to 1.76.0
(i.e. the latest) [1].
See the upgrade policy [2] and the comments on the first upgrade in
commit 3ed03f4da06e ("rust: upgrade to Rust 1.68.2").
# Unstable features
No unstable features that we use were stabilized in Rust 1.76.0.
The only unstable features allowed to be used outside the `kernel` crate
are still `new_uninit,offset_of`, though other code to be upstreamed
may increase the list.
Please see [3] for details.
# Required changes
`rustc` (and others) now warns when it cannot connect to the Make
jobserver, thus mark those invocations as recursive as needed. Please
see the previous commit for details.
# Other changes
Rust 1.76.0 does not emit the `.debug_pub{names,types}` sections anymore
for DWARFv4 [4][5]. For instance, in the uncompressed debug info case,
this debug information took:
samples/rust/rust_minimal.o ~64 KiB (~18% of total object size)
rust/kernel.o ~92 KiB (~15%)
rust/core.o ~114 KiB ( ~5%)
In the compressed debug info (zlib) case:
samples/rust/rust_minimal.o ~11 KiB (~6%)
rust/kernel.o ~17 KiB (~5%)
rust/core.o ~21 KiB (~1.5%)
In addition, the `rustc_codegen_gcc` backend now does not emit the
`.eh_frame` section when compiling under `-Cpanic=abort` [6], thus
removing the need for the patch in the CI to compile the kernel [7].
Moreover, it also now emits the `.comment` section too [6].
# `alloc` upgrade and reviewing
The vast majority of changes are due to our `alloc` fork being upgraded
at once.
There are two kinds of changes to be aware of: the ones coming from
upstream, which we should follow as closely as possible, and the updates
needed in our added fallible APIs to keep them matching the newer
infallible APIs coming from upstream.
Instead of taking a look at the diff of this patch, an alternative
approach is reviewing a diff of the changes between upstream `alloc` and
the kernel's. This allows to easily inspect the kernel additions only,
especially to check if the fallible methods we already have still match
the infallible ones in the new version coming from upstream.
Another approach is reviewing the changes introduced in the additions in
the kernel fork between the two versions. This is useful to spot
potentially unintended changes to our additions.
To apply these approaches, one may follow steps similar to the following
to generate a pair of patches that show the differences between upstream
Rust and the kernel (for the subset of `alloc` we use) before and after
applying this patch:
# Get the difference with respect to the old version.
git -C rust checkout $(linux/scripts/min-tool-version.sh rustc)
git -C linux ls-tree -r --name-only HEAD -- rust/alloc |
cut -d/ -f3- |
grep -Fv README.md |
xargs -IPATH cp rust/library/alloc/src/PATH linux/rust/alloc/PATH
git -C linux diff --patch-with-stat --summary -R > old.patch
git -C linux restore rust/alloc
# Apply this patch.
git -C linux am rust-upgrade.patch
# Get the difference with respect to the new version.
git -C rust checkout $(linux/scripts/min-tool-version.sh rustc)
git -C linux ls-tree -r --name-only HEAD -- rust/alloc |
cut -d/ -f3- |
grep -Fv README.md |
xargs -IPATH cp rust/library/alloc/src/PATH linux/rust/alloc/PATH
git -C linux diff --patch-with-stat --summary -R > new.patch
git -C linux restore rust/alloc
Now one may check the `new.patch` to take a look at the additions (first
approach) or at the difference between those two patches (second
approach). For the latter, a side-by-side tool is recommended.
Link: https://github.com/rust-lang/rust/blob/stable/RELEASES.md#version-1760-2024-02-08 [1]
Link: https://rust-for-linux.com/rust-version-policy [2]
Link: https://github.com/Rust-for-Linux/linux/issues/2 [3]
Link: https://github.com/rust-lang/compiler-team/issues/688 [4]
Link: https://github.com/rust-lang/rust/pull/117962 [5]
Link: https://github.com/rust-lang/rust/pull/118068 [6]
Link: https://github.com/Rust-for-Linux/ci-rustc_codegen_gcc [7]
Tested-by: Boqun Feng <boqun.feng@gmail.com>
Reviewed-by: Alice Ryhl <aliceryhl@google.com>
Link: https://lore.kernel.org/r/20240217002638.57373-2-ojeda@kernel.org
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
|
|
`rustc` (like Cargo) may take advantage of the jobserver at any time
(e.g. for backend parallelism, or eventually frontend too). In the kernel,
we call `rustc` with `-Ccodegen-units=1` (and `-Zthreads` is 1 so far),
so we do not expect parallelism. However, in the upcoming Rust 1.76.0, a
warning is emitted by `rustc` [1] when it cannot connect to the jobserver
it was passed (in many cases, but not all: compiling and `--print sysroot`
do, but `--version` does not). And given GNU Make always passes
the jobserver in the environment variable (even when a line is deemed
non-recursive), `rustc` will end up complaining about it (in particular
in Make 4.3 where there is only the simple pipe jobserver style).
One solution is to remove the jobserver from `MAKEFLAGS`. However, we
can mark the lines with calls to `rustc` (and Cargo) as recursive, which
looks simpler. This is being documented as a recommendation in `rustc`
[2] and allows us to be ready for the time we may use parallelism inside
`rustc` (potentially now, if a user passes `-Zthreads`). Thus do so.
Similarly, do the same for `rustdoc` and `cargo` calls.
Finally, there is one case that the solution does not cover, which is the
`$(shell ...)` call we have. Thus, for that one, set an empty `MAKEFLAGS`
environment variable.
Link: https://github.com/rust-lang/rust/issues/120515 [1]
Acked-by: Masahiro Yamada <masahiroy@kernel.org>
Link: https://github.com/rust-lang/rust/pull/121564 [2]
Link: https://lore.kernel.org/r/20240217002638.57373-1-ojeda@kernel.org
[ Reworded to add link to PR documenting the recommendation. ]
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from bluetooth, WiFi and netfilter.
We have one outstanding issue with the stmmac driver, which may be a
LOCKDEP false positive, not a blocker.
Current release - regressions:
- netfilter: nf_tables: re-allow NFPROTO_INET in
nft_(match/target)_validate()
- eth: ionic: fix error handling in PCI reset code
Current release - new code bugs:
- eth: stmmac: complete meta data only when enabled, fix null-deref
- kunit: fix again checksum tests on big endian CPUs
Previous releases - regressions:
- veth: try harder when allocating queue memory
- Bluetooth:
- hci_bcm4377: do not mark valid bd_addr as invalid
- hci_event: fix handling of HCI_EV_IO_CAPA_REQUEST
Previous releases - always broken:
- info leak in __skb_datagram_iter() on netlink socket
- mptcp:
- map v4 address to v6 when destroying subflow
- fix potential wake-up event loss due to sndbuf auto-tuning
- fix double-free on socket dismantle
- wifi: nl80211: reject iftype change with mesh ID change
- fix small out-of-bound read when validating netlink be16/32 types
- rtnetlink: fix error logic of IFLA_BRIDGE_FLAGS writing back
- ipv6: fix potential "struct net" ref-leak in inet6_rtm_getaddr()
- ip_tunnel: prevent perpetual headroom growth with huge number of
tunnels on top of each other
- mctp: fix skb leaks on error paths of mctp_local_output()
- eth: ice: fixes for DPLL state reporting
- dpll: rely on rcu for netdev_dpll_pin() to prevent UaF
- eth: dpaa: accept phy-interface-type = '10gbase-r' in the device
tree"
* tag 'net-6.8-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (73 commits)
dpll: fix build failure due to rcu_dereference_check() on unknown type
kunit: Fix again checksum tests on big endian CPUs
tls: fix use-after-free on failed backlog decryption
tls: separate no-async decryption request handling from async
tls: fix peeking with sync+async decryption
tls: decrement decrypt_pending if no async completion will be called
gtp: fix use-after-free and null-ptr-deref in gtp_newlink()
net: hsr: Use correct offset for HSR TLV values in supervisory HSR frames
igb: extend PTP timestamp adjustments to i211
rtnetlink: fix error logic of IFLA_BRIDGE_FLAGS writing back
tools: ynl: fix handling of multiple mcast groups
selftests: netfilter: add bridge conntrack + multicast test case
netfilter: bridge: confirm multicast packets before passing them up the stack
netfilter: nf_tables: allow NFPROTO_INET in nft_(match/target)_validate()
Bluetooth: qca: Fix triggering coredump implementation
Bluetooth: hci_qca: Set BDA quirk bit if fwnode exists in DT
Bluetooth: qca: Fix wrong event type for patch config command
Bluetooth: Enforce validation on max value of connection interval
Bluetooth: hci_event: Fix handling of HCI_EV_IO_CAPA_REQUEST
Bluetooth: mgmt: Fix limited discoverable off timeout
...
|
|
The update_cpumask(), checks for newly requested cpumask by calling
validate_change(), which returns an error on passing an invalid set
of cpu(s). Independent of the error returned, update_cpumask() always
returns zero, suppressing the error and returning success to the user
on writing an invalid cpu range for a cpuset. Fix it by returning
retval instead, which is returned by validate_change().
Fixes: 99fe36ba6fc1 ("cgroup/cpuset: Improve temporary cpumasks handling")
Signed-off-by: Kamalesh Babulal <kamalesh.babulal@oracle.com>
Reviewed-by: Waiman Long <longman@redhat.com>
Cc: stable@vger.kernel.org # v6.6+
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mic/linux
Pull Landlock fix from Mickaël Salaün:
"Fix a potential issue when handling inodes with inconsistent
properties"
* tag 'landlock-6.8-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/mic/linux:
landlock: Fix asymmetric private inodes referring
|
|
We've removed the SLAB allocator, cpuset_do_slab_mem_spread() and
SLAB_MEM_SPREAD, memory_spread_slab is a no-op now. We can mark
memory_spread_slab as obsolete in case someone still wants to use it after
cpuset_do_slab_mem_spread() removed. For more details, please check [1].
[1] https://lore.kernel.org/lkml/32bc1403-49da-445a-8c00-9686a3b0d6a3@redhat.com/T/#m8e292e21b00f95a4bb8086371fa7387fa4ea8f60
tj: Description and cosmetic updates.
Signed-off-by: Xiongwei Song <xiongwei.song@windriver.com>
Acked-by: Waiman Long <longman@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
The SLAB allocator has been removed sine 6.8-rc1 [1], so there is no user
with SLAB_MEM_SPREAD and cpuset_do_slab_mem_spread(). Then SLAB_MEM_SPREAD
is marked as unused by [2]. Here we can remove
cpuset_do_slab_mem_spread(). For more details, please check [3].
[1] https://lore.kernel.org/linux-mm/20231120-slab-remove-slab-v2-0-9c9c70177183@suse.cz/
[2] https://lore.kernel.org/linux-kernel/20240223-slab-cleanup-flags-v2-0-02f1753e8303@suse.cz/T/
[3] https://lore.kernel.org/lkml/32bc1403-49da-445a-8c00-9686a3b0d6a3@redhat.com/T/#mf14b838c5e0e77f4756d436bac3d8c0447ea4350
Signed-off-by: Xiongwei Song <xiongwei.song@windriver.com>
Reviewed-by: Waiman Long <longman@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Offset vmemmap so that the first page of vmemmap will be mapped
to the first page of physical memory in order to ensure that
vmemmap’s bounds will be respected during
pfn_to_page()/page_to_pfn() operations.
The conversion macros will produce correct SV39/48/57 addresses
for every possible/valid DRAM_BASE inside the physical memory limits.
v2:Address Alex's comments
Suggested-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Signed-off-by: Dimitris Vlachos <dvlachos@ics.forth.gr>
Reported-by: Dimitris Vlachos <dvlachos@ics.forth.gr>
Closes: https://lore.kernel.org/linux-riscv/20240202135030.42265-1-csd4492@csd.uoc.gr
Fixes: d95f1a542c3d ("RISC-V: Implement sparsemem")
Reviewed-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Link: https://lore.kernel.org/r/20240229191723.32779-1-dvlachos@ics.forth.gr
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
Tasmiya reports that their compiler complains that we deref
a pointer to unknown type with rcu_dereference_rtnl():
include/linux/rcupdate.h:439:9: error: dereferencing pointer to incomplete type ‘struct dpll_pin’
Unclear what compiler it is, at the moment, and we can't report
but since DPLL can't be a module - move the code from the header
into the source file.
Fixes: 0d60d8df6f49 ("dpll: rely on rcu for netdev_dpll_pin()")
Reported-by: Tasmiya Nalatwad <tasmiya@linux.vnet.ibm.com>
Link: https://lore.kernel.org/all/3fcf3a2c-1c1b-42c1-bacb-78fdcd700389@linux.vnet.ibm.com/
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20240229190515.2740221-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Alexandre Ghiti <alexghiti@rivosinc.com> says:
This contains 2 fixes for NAPOT: patch 1 disables the use of NAPOT
mapping for vmalloc/vmap and patch 2 implements pte_leaf_size() to
report NAPOT size.
* b4-shazam-merge:
riscv: Fix pte_leaf_size() for NAPOT
Revert "riscv: mm: support Svnapot in huge vmap"
Link: https://lore.kernel.org/r/20240227205016.121901-1-alexghiti@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
pte_leaf_size() must be reimplemented to add support for NAPOT mappings.
Fixes: 82a1a1f3bfb6 ("riscv: mm: support Svnapot in hugetlb page")
Signed-off-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Link: https://lore.kernel.org/r/20240227205016.121901-3-alexghiti@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
This reverts commit ce173474cf19fe7fbe8f0fc74e3c81ec9c3d9807.
We cannot correctly deal with NAPOT mappings in vmalloc/vmap because if
some part of a NAPOT mapping is unmapped, the remaining mapping is not
updated accordingly. For example:
ptr = vmalloc_huge(64 * 1024, GFP_KERNEL);
vunmap_range((unsigned long)(ptr + PAGE_SIZE),
(unsigned long)(ptr + 64 * 1024));
leads to the following kernel page table dump:
0xffff8f8000ef0000-0xffff8f8000ef1000 0x00000001033c0000 4K PTE N .. .. D A G . . W R V
Meaning the first entry which was not unmapped still has the N bit set,
which, if accessed first and cached in the TLB, could allow access to the
unmapped range.
That's because the logic to break the NAPOT mapping does not exist and
likely won't. Indeed, to break a NAPOT mapping, we first have to clear
the whole mapping, flush the TLB and then set the new mapping ("break-
before-make" equivalent). That works fine in userspace since we can handle
any pagefault occurring on the remaining mapping but we can't handle a kernel
pagefault on such mapping.
So fix this by reverting the commit that introduced the vmap/vmalloc
support.
Fixes: ce173474cf19 ("riscv: mm: support Svnapot in huge vmap")
Signed-off-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Link: https://lore.kernel.org/r/20240227205016.121901-2-alexghiti@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
Samuel Holland <samuel.holland@sifive.com> says:
This series fixes a couple of issues related to using the cbo.zero
instruction in userspace. The first patch fixes a bug where the wrong
enable bit gets set if the kernel is running in M-mode. The remaining
patches fix a bug where the enable bit gets reset to its default value
after a nonretentive idle state. I have hardware which reproduces this:
Before this series:
$ tools/testing/selftests/riscv/hwprobe/cbo
TAP version 13
1..3
ok 1 Zicboz block size
# Zicboz block size: 64
Illegal instruction
After applying this series:
$ tools/testing/selftests/riscv/hwprobe/cbo
TAP version 13
1..3
ok 1 Zicboz block size
# Zicboz block size: 64
ok 2 cbo.zero
ok 3 cbo.zero check
# Totals: pass:3 fail:0 xfail:0 xpass:0 skip:0 error:0
* b4-shazam-merge:
riscv: Save/restore envcfg CSR during CPU suspend
riscv: Add a custom ISA extension for the [ms]envcfg CSR
riscv: Fix enabling cbo.zero when running in M-mode
Link: https://lore.kernel.org/r/20240228065559.3434837-1-samuel.holland@sifive.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
The value of the [ms]envcfg CSR is lost when entering a nonretentive
idle state, so the CSR must be rewritten when resuming the CPU.
Cc: <stable@vger.kernel.org> # v6.7+
Fixes: 43c16d51a19b ("RISC-V: Enable cbo.zero in usermode")
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Link: https://lore.kernel.org/r/20240228065559.3434837-4-samuel.holland@sifive.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
The [ms]envcfg CSR was added in version 1.12 of the RISC-V privileged
ISA (aka S[ms]1p12). However, bits in this CSR are defined by several
other extensions which may be implemented separately from any particular
version of the privileged ISA (for example, some unrelated errata may
prevent an implementation from claiming conformance with Ss1p12). As a
result, Linux cannot simply use the privileged ISA version to determine
if the CSR is present. It must also check if any of these other
extensions are implemented. It also cannot probe the existence of the
CSR at runtime, because Linux does not require Sstrict, so (in the
absence of additional information) it cannot know if a CSR at that
address is [ms]envcfg or part of some non-conforming vendor extension.
Since there are several standard extensions that imply the existence of
the [ms]envcfg CSR, it becomes unwieldy to check for all of them
wherever the CSR is accessed. Instead, define a custom Xlinuxenvcfg ISA
extension bit that is implied by the other extensions and denotes that
the CSR exists as defined in the privileged ISA, containing at least one
of the fields common between menvcfg and senvcfg.
This extension does not need to be parsed from the devicetree or ISA
string because it can only be implemented as a subset of some other
standard extension.
Cc: <stable@vger.kernel.org> # v6.7+
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Link: https://lore.kernel.org/r/20240228065559.3434837-3-samuel.holland@sifive.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
When the kernel is running in M-mode, the CBZE bit must be set in the
menvcfg CSR, not in senvcfg.
Cc: <stable@vger.kernel.org>
Fixes: 43c16d51a19b ("RISC-V: Enable cbo.zero in usermode")
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20240228065559.3434837-2-samuel.holland@sifive.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
(1 << idx) of int is not desired when setting bits in unsigned long
overflowed_ctrs, use BIT() instead. This panic happens when running
'perf record -e branches' on sophgo sg2042.
[ 273.311852] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000098
[ 273.320851] Oops [#1]
[ 273.323179] Modules linked in:
[ 273.326303] CPU: 0 PID: 1475 Comm: perf Not tainted 6.6.0-rc3+ #9
[ 273.332521] Hardware name: Sophgo Mango (DT)
[ 273.336878] epc : riscv_pmu_ctr_get_width_mask+0x8/0x62
[ 273.342291] ra : pmu_sbi_ovf_handler+0x2e0/0x34e
[ 273.347091] epc : ffffffff80aecd98 ra : ffffffff80aee056 sp : fffffff6e36928b0
[ 273.354454] gp : ffffffff821f82d0 tp : ffffffd90c353200 t0 : 0000002ade4f9978
[ 273.361815] t1 : 0000000000504d55 t2 : ffffffff8016cd8c s0 : fffffff6e3692a70
[ 273.369180] s1 : 0000000000000020 a0 : 0000000000000000 a1 : 00001a8e81800000
[ 273.376540] a2 : 0000003c00070198 a3 : 0000003c00db75a4 a4 : 0000000000000015
[ 273.383901] a5 : ffffffd7ff8804b0 a6 : 0000000000000015 a7 : 000000000000002a
[ 273.391327] s2 : 000000000000ffff s3 : 0000000000000000 s4 : ffffffd7ff8803b0
[ 273.398773] s5 : 0000000000504d55 s6 : ffffffd905069800 s7 : ffffffff821fe210
[ 273.406139] s8 : 000000007fffffff s9 : ffffffd7ff8803b0 s10: ffffffd903f29098
[ 273.413660] s11: 0000000080000000 t3 : 0000000000000003 t4 : ffffffff8017a0ca
[ 273.421022] t5 : ffffffff8023cfc2 t6 : ffffffd9040780e8
[ 273.426437] status: 0000000200000100 badaddr: 0000000000000098 cause: 000000000000000d
[ 273.434512] [<ffffffff80aecd98>] riscv_pmu_ctr_get_width_mask+0x8/0x62
[ 273.441169] [<ffffffff80076bd8>] handle_percpu_devid_irq+0x98/0x1ee
[ 273.447562] [<ffffffff80071158>] generic_handle_domain_irq+0x28/0x36
[ 273.454151] [<ffffffff8047a99a>] riscv_intc_irq+0x36/0x4e
[ 273.459659] [<ffffffff80c944de>] handle_riscv_irq+0x4a/0x74
[ 273.465442] [<ffffffff80c94c48>] do_irq+0x62/0x92
[ 273.470360] Code: 0420 60a2 6402 5529 0141 8082 0013 0000 0013 0000 (6d5c) b783
[ 273.477921] ---[ end trace 0000000000000000 ]---
[ 273.482630] Kernel panic - not syncing: Fatal exception in interrupt
Reviewed-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
Signed-off-by: Fei Wu <fei2.wu@intel.com>
Link: https://lore.kernel.org/r/20240228115425.2613856-1-fei2.wu@intel.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
Add myself as a maintainer for the various SiFive drivers, since I have
been performing cleanup activity on these drivers and reviewing patches
to them for a while now. Remove Palmer as a maintainer, as he is focused
on overall RISC-V architecture support.
Collapse some duplicate entries into the main SiFive drivers entry:
- Conor is already maintainer of standalone cache drivers as a whole,
and these files are also covered by the "sifive" file name regex.
- Paul's git tree has not been updated since 2018, and all file names
matching the "fu540" pattern also match the "sifive" pattern.
- Green has not been active on the LKML for a couple of years.
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Acked-by: Paul Walmsley <paul.walmsley@sifive.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Link: https://lore.kernel.org/r/20240215234941.1663791-1-samuel.holland@sifive.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
Commit b38460bc463c ("kunit: Fix checksum tests on big endian CPUs")
fixed endianness issues with kunit checksum tests, but then
commit 6f4c45cbcb00 ("kunit: Add tests for csum_ipv6_magic and
ip_fast_csum") introduced new issues on big endian CPUs. Those issues
are once again reflected by the warnings reported by sparse.
So, fix them with the same approach, perform proper conversion in
order to support both little and big endian CPUs. Once the conversions
are properly done and the right types used, the sparse warnings are
cleared as well.
Reported-by: Erhard Furtner <erhard_f@mailbox.org>
Fixes: 6f4c45cbcb00 ("kunit: Add tests for csum_ipv6_magic and ip_fast_csum")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Tested-by: Charlie Jenkins <charlie@rivosinc.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Link: https://lore.kernel.org/r/73df3a9e95c2179119398ad1b4c84cdacbd8dfb6.1708684443.git.christophe.leroy@csgroup.eu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
Luiz Augusto von Dentz says:
====================
bluetooth pull request for net:
- mgmt: Fix limited discoverable off timeout
- hci_qca: Set BDA quirk bit if fwnode exists in DT
- hci_bcm4377: do not mark valid bd_addr as invalid
- hci_sync: Check the correct flag before starting a scan
- Enforce validation on max value of connection interval
- hci_sync: Fix accept_list when attempting to suspend
- hci_event: Fix handling of HCI_EV_IO_CAPA_REQUEST
- Avoid potential use-after-free in hci_error_reset
- rfcomm: Fix null-ptr-deref in rfcomm_check_security
- hci_event: Fix wrongly recorded wakeup BD_ADDR
- qca: Fix wrong event type for patch config command
- qca: Fix triggering coredump implementation
* tag 'for-net-2024-02-28' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth:
Bluetooth: qca: Fix triggering coredump implementation
Bluetooth: hci_qca: Set BDA quirk bit if fwnode exists in DT
Bluetooth: qca: Fix wrong event type for patch config command
Bluetooth: Enforce validation on max value of connection interval
Bluetooth: hci_event: Fix handling of HCI_EV_IO_CAPA_REQUEST
Bluetooth: mgmt: Fix limited discoverable off timeout
Bluetooth: hci_event: Fix wrongly recorded wakeup BD_ADDR
Bluetooth: rfcomm: Fix null-ptr-deref in rfcomm_check_security
Bluetooth: hci_sync: Fix accept_list when attempting to suspend
Bluetooth: Avoid potential use-after-free in hci_error_reset
Bluetooth: hci_sync: Check the correct flag before starting a scan
Bluetooth: hci_bcm4377: do not mark valid bd_addr as invalid
====================
Link: https://lore.kernel.org/r/20240228145644.2269088-1-luiz.dentz@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Sabrina Dubroca says:
====================
tls: a few more fixes for async decrypt
The previous patchset [1] took care of "full async". This adds a few
fixes for cases where only part of the crypto operations go the async
route, found by extending my previous debug patch [2] to do N
synchronous operations followed by M asynchronous ops (with N and M
configurable).
[1] https://patchwork.kernel.org/project/netdevbpf/list/?series=823784&state=*
[2] https://lore.kernel.org/all/9d664093b1bf7f47497b2c40b3a085b45f3274a2.1694021240.git.sd@queasysnail.net/
====================
Link: https://lore.kernel.org/r/cover.1709132643.git.sd@queasysnail.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When the decrypt request goes to the backlog and crypto_aead_decrypt
returns -EBUSY, tls_do_decryption will wait until all async
decryptions have completed. If one of them fails, tls_do_decryption
will return -EBADMSG and tls_decrypt_sg jumps to the error path,
releasing all the pages. But the pages have been passed to the async
callback, and have already been released by tls_decrypt_done.
The only true async case is when crypto_aead_decrypt returns
-EINPROGRESS. With -EBUSY, we already waited so we can tell
tls_sw_recvmsg that the data is available for immediate copy, but we
need to notify tls_decrypt_sg (via the new ->async_done flag) that the
memory has already been released.
Fixes: 859054147318 ("net: tls: handle backlogging of crypto requests")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Link: https://lore.kernel.org/r/4755dd8d9bebdefaa19ce1439b833d6199d4364c.1709132643.git.sd@queasysnail.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If we're not doing async, the handling is much simpler. There's no
reference counting, we just need to wait for the completion to wake us
up and return its result.
We should preferably also use a separate crypto_wait. I'm not seeing a
UAF as I did in the past, I think aec7961916f3 ("tls: fix race between
async notify and socket close") took care of it.
This will make the next fix easier.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Link: https://lore.kernel.org/r/47bde5f649707610eaef9f0d679519966fc31061.1709132643.git.sd@queasysnail.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If we peek from 2 records with a currently empty rx_list, and the
first record is decrypted synchronously but the second record is
decrypted async, the following happens:
1. decrypt record 1 (sync)
2. copy from record 1 to the userspace's msg
3. queue the decrypted record to rx_list for future read(!PEEK)
4. decrypt record 2 (async)
5. queue record 2 to rx_list
6. call process_rx_list to copy data from the 2nd record
We currently pass copied=0 as skip offset to process_rx_list, so we
end up copying once again from the first record. We should skip over
the data we've already copied.
Seen with selftest tls.12_aes_gcm.recv_peek_large_buf_mult_recs
Fixes: 692d7b5d1f91 ("tls: Fix recvmsg() to be able to peek across multiple records")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Link: https://lore.kernel.org/r/1b132d2b2b99296bfde54e8a67672d90d6d16e71.1709132643.git.sd@queasysnail.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
With mixed sync/async decryption, or failures of crypto_aead_decrypt,
we increment decrypt_pending but we never do the corresponding
decrement since tls_decrypt_done will not be called. In this case, we
should decrement decrypt_pending immediately to avoid getting stuck.
For example, the prequeue prequeue test gets stuck with mixed
modes (one async decrypt + one sync decrypt).
Fixes: 94524d8fc965 ("net/tls: Add support for async decryption of tls records")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Link: https://lore.kernel.org/r/c56d5fc35543891d5319f834f25622360e1bfbec.1709132643.git.sd@queasysnail.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In configurations with CONFIG_TICK_ONESHOT but no CONFIG_NO_HZ or
CONFIG_HIGH_RES_TIMERS, tick_sched_timer_dying() is stubbed out,
but still defined as a global function as well:
kernel/time/tick-sched.c:1599:6: error: redefinition of 'tick_sched_timer_dying'
1599 | void tick_sched_timer_dying(int cpu)
| ^
kernel/time/tick-sched.h:111:20: note: previous definition is here
111 | static inline void tick_sched_timer_dying(int cpu) { }
| ^
This configuration only appears with ARM CONFIG_ARCH_BCM_MOBILE,
which should not actually select CONFIG_TICK_ONESHOT.
Adjust the #ifdef for the stub to match the condition for building the
tick-sched.c file for consistency with the definition and to avoid
the build regression.
Fixes: 3aedb7fcd88a ("tick/sched: Remove useless oneshot ifdeffery")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240228123850.3499024-1-arnd@kernel.org
|
