| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Clear page tables after allocating them in case
we don't completely fill them later.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The DMA ring seems to be stable now.
v2: remove pt_ring_index as well
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Stop fiddling with jiffies, always wait for RADEON_FENCE_JIFFIES_TIMEOUT.
Consolidate the two wait sequence implementations into just one function.
Activate all waiters and remember if the reset was already done instead of
trying to reset from only one thread.
v2: clear reset flag earlier to avoid timeout in IB test
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
It is said to cause hangs.
Signed-off-by: Marek Olšák <marek.olsak@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The parameter is in bytes not dwords.
Signed-off-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Make sure the UVD clocks are still active before sending
the destroy message, otherwise the hw might hang.
Signed-off-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Typo in the register offset.
Noticed-by: Sylvain BERTRAND <sylware@legeek.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
The buffers needs to be in little endian format.
Noticed-by: Sylvain BERTRAND <sylware@legeek.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
If the user has forced the state high or low, retain that preference
even when we switch power states.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=70654
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
If the thermal state is active, we are in the lowest performance level
to cool down the chip. Don't let the user force it higher.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Seems to be stable on them.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Seems to be stable on them. There are still some issues
with the performance states staying in the highest levels
on certain cards when multiple monitors are attached, but
being that the the cards are always in their highest power
state at boot up anyway, this doesn't really change anything
and improves things in all other cases.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here is a set of patches that revert all of the changes done to the
pl2303 USB serial driver in the 3.12-rc timeframe, as it turns out
they break some devices that work just fine on 3.11. As it's not a
good idea to break working systems, drop them all and they will be
reworked for future kernel versions such that there is no breakage.
I've also included a MAINTAINERS update for the USB serial subsystem
and a new device id for the ftdi_sio driver as well"
* tag 'usb-3.12-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: serial: ftdi_sio: add id for Z3X Box device
USB: Maintainers change for usb serial drivers
Revert "USB: pl2303: restrict the divisor based baud rate encoding method to the "HX" chip type"
Revert "usb: pl2303: fix+improve the divsor based baud rate encoding method"
Revert "usb: pl2303: do not round to the next nearest standard baud rate for the divisor based baud rate encoding method"
Revert "usb: pl2303: remove 500000 baud from the list of standard baud rates"
Revert "usb: pl2303: move the two baud rate encoding methods to separate functions"
Revert "usb: pl2303: increase the allowed baud rate range for the divisor based encoding method"
Revert "usb: pl2303: also use the divisor based baud rate encoding method for baud rates < 115200 with HX chips"
Revert "usb: pl2303: add two comments concerning the supported baud rates with HX chips"
Revert "pl2303: simplify the else-if contruct for type_1 chips in pl2303_startup()"
Revert "pl2303: improve the chip type information output on startup"
Revert "pl2303: improve the chip type detection/distinction"
Revert "USB: pl2303: distinguish between original and cloned HX chips"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull more sound fixes from Takashi Iwai:
"The fixes for random bugs that have been reported lately in the game:
a few fixes in ASoC dpam and wm_hubs bugs spotted by Coverity, a
one-liner HD-audio fixup, and a fix for Oops with DPCM.
They are not so critically urgent bugs, but all small and safe"
* tag 'sound-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: fix oops in snd_pcm_info() caused by ASoC DPCM
ASoC: wm_hubs: Add missing break in hp_supply_event()
ALSA: hda - Add a fixup for ASUS N76VZ
ASoC: dapm: Return -ENOMEM in snd_soc_dapm_new_dai_widgets()
ASoC: dapm: Fix source list debugfs outputs
|
|
Pull clock subsystem fixes from Mike Turquette.
* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mturquette/linux:
clk: fixup argument order when setting VCO parameters
clk: socfpga: Fix incorrect sdmmc clock name
clk: armada-370: fix tclk frequencies
clk: nomadik: set all timers to use 2.4 MHz TIMCLK
|
|
When a memcg is deleted mem_cgroup_reparent_charges() moves charged
memory to the parent memcg. As of v3.11-9444-g3ea67d0 "memcg: add per
cgroup writeback pages accounting" there's bad pointer read. The goal
was to check for counter underflow. The counter is a per cpu counter
and there are two problems with the code:
(1) per cpu access function isn't used, instead a naked pointer is used
which easily causes oops.
(2) the check doesn't sum all cpus
Test:
$ cd /sys/fs/cgroup/memory
$ mkdir x
$ echo 3 > /proc/sys/vm/drop_caches
$ (echo $BASHPID >> x/tasks && exec cat) &
[1] 7154
$ grep ^mapped x/memory.stat
mapped_file 53248
$ echo 7154 > tasks
$ rmdir x
<OOPS>
The fix is to remove the check. It's currently dangerous and isn't
worth fixing it to use something expensive, such as
percpu_counter_sum(), for each reparented page. __this_cpu_read() isn't
enough to fix this because there's no guarantees of the current cpus
count. The only guarantees is that the sum of all per-cpu counter is >=
nr_pages.
Fixes: 3ea67d06e467 ("memcg: add per cgroup writeback pages accounting")
Reported-and-tested-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: Greg Thelen <gthelen@google.com>
Reviewed-by: Sha Zhengju <handai.szj@taobao.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Even though we only check for unclaimed registers while we're writing
registers, if we read a bad register we'll still trigger a CPU error
interrupt, and we'll print an "Unclaimed register" DRM_ERROR due to
that. To avoid this error, just avoid touching power domains that are
not enabled.
Use kzalloc so we're sure all the disabled domains will be zeroed on
the error state file. We already print the information that is enough
to discover if the power well is enabled on the error state file, so
this should not be a problem.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=69747
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Now that DP port CRCs are stable, we can use it for generic CRC tests.
Yay, the auto CRC source should now work everywhere!
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
They've moved the DC balance reset bit around. Again I don't think we
need it, but better safe than sorry and maybe HDMI port CRC will prove
useful for checking infoframes or hdmi audio.
v2: Apply the suggestions from Damien's review.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
We need to reset the DP scrambler on every vsync to get stable CRCs.
And since we can't use the normal pipe CRC on DP ports on g4x we
really need them to be able to test modesetting issues on (e)DP
outputs.
Note that the DC balance reset is for SDVO port CRCs so we don't
strictly need it. But better safe than sorry (and it's a nice template
in case we ever want to grab port CRCs for e.g. audio checking).
v2: Apply the suggestions from Damien's review.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
On gmch platforms the normal pipe source CRC registers don't work for
DP and TV encoders. And on newer platforms the single pipe CRC has
been replaced by a set of CRC at different stages in the platform.
Now most of our userspace tests don't care one bit about the exact
CRC, they simply want something that reflects any changes on the
screen. Hence add a new auto target for platform agnostic tests to
use.
v2: Pass back the adjusted source so that it can be shown in debugfs.
v3: I seem to be unable to get a stable CRC for DP ports. So let's
just disable them for now when using the auto mode. Note that
testcases need to be restructured so that they can dynamically skip
connectors. They also first need to set up the desired mode
configuration, since otherwise the auto mode won't do the right thing.
v4: Don't leak the modeset mutex on error paths.
v5: Spelling fix for the i9xx auto_source function.
Cc: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Seems to be stable on them.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Seems to be stable on them and improves peformance
as most SI asics have very low boot clocks.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
DPM seems to be stable on these asics and it drastically
improves performance depending on the boot clocks.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Avoids spamming the system log for chips where dpm is enabled by
default, but prints then messages when users force it on for other
asics.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Currently radeon devices are not properly shutdown during kexec. This
causes a varity of issues, e.g. dpm initialization failures.
Fix this by implementing a radeon_pci_shutdown function, that unloads
the driver cleanly.
Signed-off-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Needed by the hda driver to properly set up synchronization
on the audio side.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
|
|
Needed by the hda driver to properly set up synchronization
on the audio side.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
|
|
No need to continue with the loops once we've matched
the appropriate connector.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The plain [EN|DIS]ABLE functions do the same thing and more
and aren't broken on some systems like [EN|DIS]ABLE_OUTPUT.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The plain [EN|DIS]ABLE functions do the same thing and more
and aren't broken on some systems like [EN|DIS]ABLE_OUTPUT.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
On SI asics, the SMC will automatically force the performance
level to the lowest level if there are no displays active. This
prevents automatic performance scaling on PowerXpress systems or
for offscreen rendering or compute when displays are disabled.
Going forward, it would be best to dynamically change this, but
for now leave scaling enabled.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=69395
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Uses the CP ring rather than the DMA ring. Useful
for debugging and benchmarking.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The rv6xx_clocks_per_unit() function pretends it can set flags in a u64
bitfield but really because "1" is an int it doesn't work for more than
32 bits. The only caller truncates the high bits away anyway. I've
just changed it to be a u32.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Uses CP DMA packet just like previous asics.
Useful for debugging and benchmarking. Uses
same packet format as prior asics.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Seems to be stable enough for the majority of users.
It can be disabled on the fly via connector attributes.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This hooks radeon up to the runtime PM system to enable
dynamic power management for secondary GPUs in switchable
and powerxpress laptops.
v2: agd5f: clean up, add module parameter
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This is a pre-requisite for runtime pm on powerxpress systems.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Allows you to enable dither in the display hardware
when the monitor supports lower a lower bpc than the
current framebuffer format.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The FMT blocks control how data is sent from the backend
of the display pipe to to monitor. Proper set up of the
FMT blocks are required for 30bpp formats. Additionally,
dithering can be enabled on for better display with 18 and
24bpp displays. The exception is LVDS/eDP which atom
takes care of in the SelectCRTC_Source table. For now
just enable truncation until we test dithering more.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
There were a few potential problems with the original page_flip/vblank
code in mdp4_crtc.
1) We need vblank irq for a couple things, both completing flips and
updating cursor. We need to keep track of what work is pending so
that (for example) a cursor update while we are still waiting for
pageflip_cb (ie. pageflip requested from userspace, but still
waiting for rendering to complete) would not prematurely trigger
event to userspace.
2) A preclose -> pageflip-cancel should not cancel a pageflip that
was requested on a different file (ie. non-master closing should
not cancel a pending pageflip).
With these fixes, we no longer have problems w/ cursor not updating and
with occasional hangs with userspace waiting for a pageflip that had
been cancelled (launching XBMC from gnome-shell overview mode was a good
way to trigger this, but now works reliably).
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Subsequent threads returning EBUSY from vm_insert_pfn() was not
handled correctly. As a result concurrent access from new threads
to mmapped data caused SIGBUS.
See e79e0fe3
Signed-off-by: Rob Clark <robdclark@gmail.com>
Acked-by: David Brown <davidb@codeaurora.org>
|
|
Re-arrange things a bit so that we can get work requested after a bo
fence passes, like pageflip, done before retiring bo's. Without any
sort of bo cache in userspace, some games can trigger hundred's of
transient bo's, which can cause retire to take a long time (5-10ms).
Obviously we want a bo cache.. but this cleanup will make things a
bit easier for atomic as well and makes things a bit cleaner.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Acked-by: David Brown <davidb@codeaurora.org>
|
|
Enable using VG1 and VG2 for planes. Currently YUV/CSC or scaling is
not enabled, but ARGB and xRGB blending is.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Acked-by: David Brown <davidb@codeaurora.org>
|
|
resync to latest envytools db, fixes a typo: s/mpd4/mdp4/
Signed-off-by: Rob Clark <robdclark@gmail.com>
Acked-by: David Brown <davidb@codeaurora.org>
|
|
Enable support for drm render nodes for msm by flagging the ioctls
that are safe and only needed for rendering.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Acked-by: David Brown <davidb@codeaurora.org>
|
|
Signed-off-by: Rob Clark <robdclark@gmail.com>
Acked-by: David Brown <davidb@codeaurora.org>
|
|
Custom VID/PID for Z3X Box device, popular tool for cellphone flashing.
Signed-off-by: Alexey E. Kramarenko <alexeyk13@yandex.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
