| Age | Commit message (Collapse) | Author |
|---|
|
The CS helper functions were toggling both the Flag Enable and the Flag
Value bits, but the Flag Value bit is ignored if the corresponding Flag
Enable bit is cleared. So under high speed transactions, the CS sometimes
would not toggle properly.
Since it makes no sense to toggle the Flag Enable bit dynamically when we
actually want to control the Flag Value, do this when setting up the device
and then only handle toggling of the CS value during runtime.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
The current behavior in PIO mode is to poll the SPI status registers which
can obviously lead to higher latencies when doing a lot of SPI traffic.
There is a SPI interrupt which can be used instead to signal individual
completion of transactions.
Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
We should make sure the SPI controller is in a sane state in case the
boot loader left it in a crappy state. Such as DMA pending which causes
interrupts to fire on us.
When setting a sane initial state, do not default to slave mode. If we
do, then the SPI peripheral may implicitly take over the SPISS pin which
other things might be using.
For example, the BF533-STAMP uses this pin as a GPIO to control switching
between ethernet and flash. If the SPI peripheral controls the output
state instead, the ethernet is no longer accessible.
URL: http://blackfin.uclinux.org/gf/tracker/5630
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Anomaly 05000119 states that the DMA_RUN bit with peripherals isn't
reliable. However, the way the driver is currently written (DMA IRQ
callback), we don't need the polling in the first place, so drop it.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Re-order setup() a bit so we don't leak memory/dma/gpio resources upon
errors. Also make sure we don't call kfree() twice on the same object.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
* Rename shpchp_wq to shpchp_ordered_wq and add non-ordered shpchp_wq
which is used instead of the system workqueue. This is to remove
the use of flush_scheduled_work() which is deprecated and scheduled
for removal.
* With cmwq in place, there's no point in creating workqueues lazily.
Create both shpchp_wq and shpchp_ordered_wq upfront.
* Include workqueue.h from shpchp.h.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
* Rename pciehp_wq to pciehp_ordered_wq and add non-ordered pciehp_wq
which is used instead of the system workqueue. This is to remove
the use of flush_scheduled_work() which is deprecated and scheduled
for removal.
* With cmwq in place, there's no point in creating workqueues lazily.
Create both pciehp_wq and pciehp_ordered_wq upfront.
* Include workqueue.h from pciehp.h.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
This patch updates the Kconfig and Makefile for the S5P6440 and S5P6450
machines. It also updates arch/arm/ Kconfig and Makefile to include for
support ARCH_S5P64X0 with one kernel image.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This patch moves some initial maps from plat-s5p to machine,
so that can merge mach-s5p6440 and mach-s5p6450.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This patch moves OneNAND device definitions from mach-s5pv210 to plat-s5p
so that can support it commonly.
Note: S5PC110 and S5PC210 have same OneNAND driver.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
|
|
...and make it non-inlined in preparation for the move of most of
cifs_close to it.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Reviewed-by: Suresh Jayaraman <sjayaraman@suse.de>
Signed-off-by: Steve French <sfrench@us.ibm.com>
|
|
Convert this lock to a regular spinlock
A rwlock_t offers little value here. It's more expensive than a regular
spinlock unless you have a fairly large section of code that runs under
the read lock and can benefit from the concurrency.
Additionally, we need to ensure that the refcounting for files isn't
racy and to do that we need to lock areas that can increment it for
write. That means that the areas that can actually use a read_lock are
very few and relatively infrequently used.
While we're at it, change the name to something easier to type, and fix
a bug in find_writable_file. cifsFileInfo_put can sleep and shouldn't be
called while holding the lock.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Reviewed-by: Suresh Jayaraman <sjayaraman@suse.de>
Signed-off-by: Steve French <sfrench@us.ibm.com>
|
|
Signed-off-by: Steve French <sfrench@us.ibm.com>
|
|
It's currently in dir.c which makes little sense...
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Reviewed-by: Suresh Jayaraman <sjayaraman@suse.de>
Acked-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
|
|
All the remaining users of cifsFileInfo->pfile just use it to get
at the f_flags/f_mode. Now that we store that separately in the
cifsFileInfo, there's no need to consult the pfile at all from
a cifsFileInfo pointer.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Reviewed-by: Suresh Jayaraman <sjayaraman@suse.de>
Acked-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
|
|
Have cifs_write take a cifsFileInfo pointer instead of a filp. Since
cifsFileInfo holds references on the dentry, and that holds one to
the inode, we can eliminate some unneeded NULL pointer checks.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Reviewed-by: Suresh Jayaraman <sjayaraman@suse.de>
Acked-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
|
|
Add a f_flags field that holds the f_flags field from the filp. We'll
need this info in case the filp ever goes away before the cifsFileInfo
does. Have cifs_reopen_file use that value instead of filp->f_flags
too and have it take a cifsFileInfo arg instead of a filp.
While we're at it, get rid of some bogus cargo-cult NULL pointer
checks in that function and reduce the level of indentation.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Reviewed-by: Suresh Jayaraman <sjayaraman@suse.de>
Acked-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
|
|
It already takes a file pointer. The inode associated with that had damn
well better be the same one we're passing in anyway. Thus, there's no
need for a separate argument here.
Also, get rid of the bogus check for a null pCifsInode pointer. The
CIFS_I macro uses container_of(), and that will virtually never return a
NULL pointer anyway.
Finally, move the setting of the canCache* flags outside of the lock.
Other places in the code don't hold that lock when setting it, so I
assume it's not really needed here either.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Reviewed-by: Suresh Jayaraman <sjayaraman@suse.de>
Acked-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
|
|
Eliminate the poor, misunderstood "oflags" option from cifs_new_fileinfo.
The callers mostly pass in the filp->f_flags here.
That's not correct however since we're checking that value for
the presence of FMODE_READ. Luckily that only affects how the f_list is
ordered. What it really wants here is the file->f_mode. Just use that
field from the filp to determine it.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Reviewed-by: Suresh Jayaraman <sjayaraman@suse.de>
Signed-off-by: Steve French <sfrench@us.ibm.com>
|
|
The way flags are passed and converted for cifs_posix_open is rather
non-sensical. Some callers call cifs_posix_convert_flags on the flags
before they pass them to cifs_posix_open, whereas some don't. Two flag
conversion steps is just confusing though.
Change the function instead to clearly expect input in f_flags format,
and fix the callers to pass that in. Then, have cifs_posix_open call
cifs_convert_posix_flags to do the conversion. Move cifs_posix_open to
file.c as well so we can keep cifs_convert_posix_flags as a static
function.
Fix it also to not ignore O_CREAT, O_EXCL and O_TRUNC, and instead have
cifs_reopen_file mask those bits off before calling cifs_posix_open.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Reviewed-by: Suresh Jayaraman <sjayaraman@suse.de>
Signed-off-by: Steve French <sfrench@us.ibm.com>
|
|
The i2c_imx_trx_complete() function is using
wait_event_interruptible_timeout() to wait for the I2C controller to
signal that it has completed an I2C bus operation. If the process that
causes the I2C operation receives a signal, the wait will be
interrupted, returning an error. It is better to let the I2C operation
finished before handling the signal (i.e. returning into userspace).
It is safe to use wait_event_timeout() instead, because the timeout
will allow the process to exit if the I2C bus hangs. It's also better
to allow the I2C operation to finish, because unacknowledged I2C
operations can cause the I2C bus to hang.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
This patch is an improvement to 4bba0fd8d1c6d405df666e2573e1a1f917098be0
which got to mainline a little early.
Sudhakar Rajashekhara explains that at least OMAP-L138 requires MDR mode
settings before DXR for correct behaviour, so load MDR first with
STT cleared and later load again with STT set.
Tested on DM355 connected to Techwell TW2836 and Wolfson WM8985
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
Acked-by: Troy Kisky <troy.kisky@boundarydevices.com>
Tested-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
In error cases when the ACL is insecure or we fail to allocate a new
struct sock, we jump to the "response" label. If so, "sk" will be
null and the kernel crashes.
Signed-off-by: Nathan Holstein <nathan.holstein@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
Fixes cursor corruption in certain cases.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
This patch updates the tg3 version to 3.115.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently the tg3 driver leaves the speed and duplex fields
uninitialized in tg3_get_settings() if the device is not up. This can
lead to some strange deductions in certain versions of ethtool. When
the device is up and the link is down, the driver reports SPEED_INVALID
and DUPLEX_INVALID for these fields. This patch makes the presentation
consistent by returning SPEED_INVALID and DUPLEX_INVALID when the device
has not been brought up as well.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 5714, 5715, and 5780 devices do not have a separate rx jumbo
producer ring. This patch changes the code so that resources are not
allocated for it.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
src_map is no longer used in tg3_alloc_rx_skb(). Remove it.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds Energy Efficient Ethernet (EEE) support for the 5718
device ID and the 57765 B0 asic revision.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds clause 45 register access methods. They will be used in
the following patch.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch allows the driver to disable the additional transmit rings
available on the 5717 and 5719 devices. This is not strictly necessary,
but is done anyways for correctness.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
5718 B0 and 5719 devices will use a new selfboot firmware format. This
patch adds code to detect the new format so that bootcode versions get
reported correctly.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Get rid of fib_hash_lock rwlock.
The fn_zone hash table resize is the noticeable part of this patch.
I added a seqlock per fn_zone, so that readers can restart their lookup
in the (very rare) case a writer expanded the hash table.
Add rcu heads in fib_alias and fib_node, use call_rcu() to defer their
freeing, and use appropriate _rcu list manipulations.
Stress test (160.000.000 udp frames sent, IP route cache disabled to
mimic DDOS attack, FIB_HASH)
Before:
real 0m41.191s
user 0m13.137s
sys 8m55.241s
After:
real 0m38.091s
user 0m13.189s
sys 7m53.018s
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
First step for RCU conversion of fib_hash :
struct fn_zone are created and never deleted.
Very classic conversion, using rcu_assign_pointer(), rcu_dereference()
and rtnl_dereference() verbs.
__rcu markers on fz_next and fn_zone_list
They are created under RTNL, we dont need fib_hash_lock anymore in
fn_new_zone().
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While looking for false sharing problems, I noticed
sizeof(struct fn_zone) was small (28 bytes) and possibly sharing a cache
line with an often written kernel structure.
Most of the time, fn_zone uses its initial hash table of 16 slots.
We can avoid the false sharing problem by embedding this initial hash
table in fn_zone itself, so that sizeof(fn_zone) > L1_CACHE_BYTES
We did a similar optimization in commit a6501e080c (Reduce memory needs
and speedup lookups)
Add a fz_revorder field to speedup fn_hash() a bit.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the standard macro to put this table in __devinitconst.
Compiled, untested.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In a network bench, I noticed an unfortunate false sharing between
'loopback_dev' and 'count' fields in "struct net".
'count' is written each time a socket is created or destroyed, while
loopback_dev might be often read in routing code.
Move loopback_dev in a read mostly section of "struct net"
Note: struct netns_xfrm is cache line aligned on SMP.
(It contains a "struct dst_ops")
Move it at the end to avoid holes, and reduce sizeof(struct net) by 128
bytes on ia32.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As CWR is stronger than CA_Disorder state, we can miscount
SACK/Reno failure into other timeouts. Not a bad problem as
it can happen only due to ECN, FRTO detecting spurious RTO
or xmit error which are the only callers of tcp_enter_cwr.
And even then losses and RTO must still follow thereafter
to actually end up into the relevant code paths.
Compile tested.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When only fast rexmit should be done, tcp_mark_head_lost marks
L too far. Also, sacked_upto below 1 is perfectly valid number,
the packets == 0 then needs to be trapped elsewhere.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reported-by: Armando Visconti <armando.visconti@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Suppress a large block of warnings like:
drivers/net/niu.c:7094:38: warning: incorrect type in assignment (different base types)
drivers/net/niu.c:7094:38: expected restricted __be32 [usertype] ip4src
drivers/net/niu.c:7094:38: got unsigned long long
drivers/net/niu.c:7104:17: warning: cast from restricted __be32
...
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'fix/misc' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: rawmidi: fix oops (use after free) when unloading a driver module
|
|
Add a commentary which elaborates that 'ubifs_recover_log_leb()' recovers only
the last log LEB, not any. Also remove some unneeded newlines.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
Revert commit 54672386ccf36ffa21d1de8e75624af83f9b0eeb
"firewire: ohci: fix up configuration of TI chips".
It caused massive slow-down and data corruption with a TSB82AA2 based
StarTech EC1394B2 ExpressCard and FireWire 800 harddisks.
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/657081
http://thread.gmane.org/gmane.linux.kernel.firewire.user/4013
The fact that some card EEPROMs do not program these enhancements may be
related to TSB81BA3 phy chip errata, if not to bugs of TSB82AA2 itself.
We could re-add these configuration steps, but only conditional on a
whitelist of cards on which these enhancements bring a proven positive
effect.
Reported-and-tested-by: Eric Shattow <lucent@gmail.com>
Cc: Clemens Ladisch <clemens@ladisch.de>
Cc: <stable@kernel.org> 2.6.35
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
diva doesn't use workqueue and there is no reason to flush the system
workqueue from diva_os_remove_soft_isr(). Remove it.
This is to prepare for the deprecation and removal of
flush_scheduled_work().
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Armin Schindler <armin@melware.de>
|
|
When a driver module is unloaded and the last still open file is a raw
MIDI device, the card and its devices will be actually freed in the
snd_card_file_remove() call when that file is closed. Afterwards, rmidi
and rmidi->card point into freed memory, so the module pointer is likely
to be garbage.
(This was introduced by commit 9a1b64caac82aa02cb74587ffc798e6f42c6170a.)
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Reported-by: Krzysztof Foltman <wdev@foltman.com>
Cc: 2.6.30-2.6.35 <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
SoCs have a standard set of tuples consisting of frequency and
voltage pairs that the device will support per voltage domain. These
are called Operating Performance Points or OPPs. The actual
definitions of OPP varies over silicon versions. For a specific domain,
we can have a set of {frequency, voltage} pairs. As the kernel boots
and more information is available, a default set of these are activated
based on the precise nature of device. Further on operation, based on
conditions prevailing in the system (such as temperature), some OPP
availability may be temporarily controlled by the SoC frameworks.
To implement an OPP, some sort of power management support is necessary
hence this library depends on CONFIG_PM.
Contributions include:
Sanjeev Premi for the initial concept:
http://patchwork.kernel.org/patch/50998/
Kevin Hilman for converting original design to device-based.
Kevin Hilman and Paul Walmsey for cleaning up many of the function
abstractions, improvements and data structure handling.
Romit Dasgupta for using enums instead of opp pointers.
Thara Gopinath, Eduardo Valentin and Vishwanath BS for fixes and
cleanups.
Linus Walleij for recommending this layer be made generic for usage
in other architectures beyond OMAP and ARM.
Mark Brown, Andrew Morton, Rafael J. Wysocki, Paul E. McKenney for
valuable improvements.
Discussions and comments from:
http://marc.info/?l=linux-omap&m=126033945313269&w=2
http://marc.info/?l=linux-omap&m=125482970102327&w=2
http://marc.info/?t=125809247500002&r=1&w=2
http://marc.info/?l=linux-omap&m=126025973426007&w=2
http://marc.info/?t=128152609200064&r=1&w=2
http://marc.info/?t=128468723000002&r=1&w=2
incorporated.
v1: http://marc.info/?t=128468723000002&r=1&w=2
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
If the device which fails to resume is part of a loadable kernel module
it won't be checked at startup against the magic number stored in the
RTC.
Add a read-only sysfs attribute /sys/power/pm_trace_dev_match which
contains a list of newline separated devices (usually just the one)
which currently match the last magic number. This allows the device
which is failing to resume to be found after the modules are loaded
again.
Signed-off-by: James Hogan <james@albanarts.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
Lock the PM device list mutex using device_pm_lock() and
device_pm_unlock() around the list iteration in show_dev_hash().
show_dev_hash() was reverse iterating dpm_list without first locking the
mutex that the functions in drivers/base/power/main.c lock. I assume
this was unintentional since there is no comment suggesting why the lock
might not be necessary.
Signed-off-by: James Hogan <james@albanarts.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
If runtime suspend of a device fails returning -EAGAIN or -EBUSY,
which means that it's safe to try to suspend it again, the PM core
runs the runtime idle helper function for it. Unfortunately this may
lead to problems, for example for PCI devices whose drivers don't
implement the ->runtime_idle() callback, because in that case the
PCI bus type's ->runtime_idle() always calls pm_runtime_suspend()
for the given device. Then, if there's an automatic idle
notification after the driver's ->runtime_suspend() returning -EAGAIN
or -EBUSY, it will make the suspend happen again possibly causing a
busy loop to appear. To avoid that, remove the idle notification
after failing runtime suspend of a device altogether and let the
callers of pm_runtime_suspend() repeat the operation if need be.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
|
