| Age | Commit message (Collapse) | Author |
|---|
|
Since 8822c requires to do not only IQK, but also DPK.
Move these calibrations that need to be done once the channel
is determined, into phy_calibration.
And note that the order of the calibrations matters, 8822c
should do IQK first, then DPK.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Power amplifiers are not linear components, and require DPK to
reduce its nonlinearity. DPK is called Digital Pre-distortion
Calibration, can be used to compensate the output of power.
DPK tracking is in charge of tracking the thermal changes. And
it then shifts the power curve accordingly, which makes the
power output remains linear even if the PA works in different
temperature.
To perform DPK, the parameter table should also be updated.
And the table will be applied when device is powered on.
Then DPK will reference the values to calibrate.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Add support for doing IQK in firmware
Ideally the RF component's I/Q vectors should be orthogonal,
but usually they are not. So we need to calibrate for the RF
components, ex. PA/LNA, ADC/DAC.
And if the I/Q vectors are more orthogonal, the mixed signal
will have less deviation. This helps with those rates with
higher modulation (MCS8-9), because they have more strict
EVM/SNR requirement. Also the better of the quality of the
signal, the longer it can propagate, and the better throughput
performance we can get.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Enable 8822C Tx/Rx interrupt migration.
In some platforms, performance test may cause heavy cpu loading and get
bad results. Interrupt migration can decrease the amount of interrupts,
and lower cpu loading.
Signed-off-by: Tsang-Shian Lin <thlin@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
update sequence to v13 to reduce power consumption
when MAC power off
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Update PHY hardware parameters to v38.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
When dumping the XIVE state of an CPU IPI, xmon does not check if the
CPU is started or not which can cause an error. Add a check for that
and change the output to be on one line just as the XIVE interrupts of
the machine.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190910081850.26038-3-clg@kaod.org
|
|
When looping on the list of interrupts, add the current value of the
PQ bits with a load on the ESB page. This has the side effect of
faulting the ESB page of all interrupts.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190910081850.26038-2-clg@kaod.org
|
|
unused bit manipulation macros
Each of these drivers defines some device to host macros that are never
used, thus they can be removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In this step, the read/write routines for the descriptors are converted
to use __le32 quantities, thus a lot of casts can be removed. Callback
routines still use the 8-bit arrays, but these are changed within the
specified routine.
The macro that cleared a descriptor has now been converted into an inline
routine.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
As a first step in the conversion, the macros that set the RX and TX
descriptors are converted to static inline routines, and the names are
changed from upper to lower case. To minimize the changes in a given
step, the input descriptor information is left as as a byte array
(u8 *), even though it should be a little-endian word array (__le32 *).
That will be changed in the next patch.
Several places where checkpatch.pl complains about a space after a cast
are fixed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This driver uses a set of local macros to manipulate the RX and TX
descriptors, which are all little-endian quantities. These macros
are replaced by the bitfield macros le32p_replace_bits() and
le32_get_bits(). In several places, the macros operated on an entire
32-bit word. In these cases, a direct read or replacement is used.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
iAs the first step in converting from macros that get/set information
in the RX and TX descriptors, unused macros are being removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In this step, the read/write routines for the descriptors are converted
to use __le32 quantities, thus a lot of casts can be removed. Callback
routines still use the 8-bit arrays, but these are changed within the
specified routine.
The macro that cleared a descriptor has now been converted into an inline
routine.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
As a first step in the conversion, the macros that set the RX and TX
descriptors are converted to static inline routines, and the names are
changed from upper to lower case. To minimize the changes in a given
step, the input descriptor information is left as as a byte array
(u8 *), even though it should be a little-endian word array (__le32 *).
That will be changed in the next patch.
Several places where checkpatch.pl reports lines too long are fixed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This driver uses a set of local macros to manipulate the RX and TX
descriptors, which are all little-endian quantities. These macros
are replaced by the bitfield macros le32p_replace_bits() and
le32_get_bits(). In several places, the macros operated on an entire
32-bit word. In these cases, a direct read or replacement is used.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
As the first step in converting from macros that get/set information
in the RX and TX descriptors, unused macros are being removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
With the commit e86dc1ca4676 ("Libertas: cfg80211 support") we've lost
the ability to actually set the Mesh SSID from userspace.
NL80211_CMD_SET_INTERFACE with NL80211_ATTR_MESH_ID sets the mesh point
interface's ssid field. Let's use that one for the Libertas Mesh
operation
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Don't populate the array pwr_info_offset on the stack but instead make it
static const. Makes the object code smaller by 207 bytes.
Before:
text data bss dec hex filename
26066 3000 64 29130 71ca drivers/ssb/pci.o
After:
text data bss dec hex filename
25763 3096 64 28923 70fb drivers/ssb/pci.o
(gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Michael Büsch <m@bues.ch>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Signed-off-by: Luis Correia <luisfcorreia@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Booting a POWER9 PowerNV system generates a few messages below with
"____ptrval____" due to the pointers printed without a specifier
extension (i.e unadorned %p) are hashed to prevent leaking information
about the kernel memory layout.
radix-mmu: Initializing Radix MMU
radix-mmu: Partition table (____ptrval____)
radix-mmu: Mapped 0x0000000000000000-0x0000000040000000 with 1.00 GiB
pages (exec)
radix-mmu: Mapped 0x0000000040000000-0x0000002000000000 with 1.00 GiB
pages
radix-mmu: Mapped 0x0000200000000000-0x0000202000000000 with 1.00 GiB
pages
radix-mmu: Process table (____ptrval____) and radix root for kernel:
(____ptrval____)
Signed-off-by: Qian Cai <cai@lca.pw>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1566570120-16529-1-git-send-email-cai@lca.pw
|
|
With support to copy multiple kernel boot memory regions owing to copy
size limitation, also handle holes in the memory area to be preserved.
Support as many as 128 kernel boot memory regions. This allows having
an adequate FADump capture kernel size for different scenarios.
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/156821385448.5656.6124791213910877759.stgit@hbathini.in.ibm.com
|
|
RMA_START is defined as '0' and there is even a BUILD_BUG_ON() to
make sure it is never anything else. Remove this macro and use '0'
instead as code change is needed anyway when it has to be something
else. Also, remove unused RMA_END macro.
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/156821384096.5656.15026984053970204652.stgit@hbathini.in.ibm.com
|
|
With /sys/firmware/opal/core support available on OPAL based machines
and an option to the release memory used by kernel in exporting this
core file, update FADump documentation with these details.
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/156821382786.5656.13173494907671241231.stgit@hbathini.in.ibm.com
|
|
OPAL loads kernel & initrd at 512MB offset (256MB size), also exported
as ibm,opal/dump/fw-load-area. So, if boot memory size of FADump is
less than 768MB, kernel memory to be exported as '/proc/vmcore' would
be overwritten by f/w while loading kernel & initrd. To avoid such a
scenario, enforce a minimum boot memory size of 768MB on OPAL platform
and skip using FADump if a newer F/W version loads kernel & initrd
above 768MB.
Also, irrespective of RMA size, set the minimum boot memory size
expected on pseries platform at 320MB. This is to avoid inflating the
minimum memory requirements on systems with 512M/1024M RMA size.
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/156821381414.5656.1592867278535469652.stgit@hbathini.in.ibm.com
|
|
Writing '1' to /sys/kernel/fadump_release_opalcore would release the
memory held by kernel in exporting /sys/firmware/opal/core file.
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/156821380161.5656.17827032108471421830.stgit@hbathini.in.ibm.com
|
|
Export /sys/firmware/opal/core file to analyze opal crashes. Since OPAL
core can be generated independent of CONFIG_FA_DUMP support in kernel,
add this support under a new kernel config option CONFIG_OPAL_CORE.
Also, avoid code duplication by moving common code used while exporting
/proc/vmcore and/or /sys/firmware/opal/core file(s).
Signed-off-by: Hari Bathini <hbathini@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/156821378503.5656.3693769384945087756.stgit@hbathini.in.ibm.com
|
|
Kernel config option CONFIG_PRESERVE_FA_DUMP is introduced to ensure
crash data, from previously crash'ed kernel, is preserved. Update
documentation with this details.
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/156821377195.5656.15840065629705958324.stgit@hbathini.in.ibm.com
|
|
Add a new kernel config option, CONFIG_PRESERVE_FA_DUMP that ensures
that crash data, from previously crash'ed kernel, is preserved. This
helps in cases where FADump is not enabled but the subsequent memory
preserving kernel boot is likely to process this crash data. One
typical usecase for this config option is petitboot kernel.
As OPAL allows registering address with it in the first kernel and
retrieving it after MPIPL, use it to store the top of boot memory.
A kernel that intends to preserve crash data retrieves it and avoids
using memory beyond this address.
Move arch_reserved_kernel_pages() function as it is needed for both
FA_DUMP and PRESERVE_FA_DUMP configurations.
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/156821375751.5656.11459483669542541602.stgit@hbathini.in.ibm.com
|
|
The size parameter to fadump_reserve_crash_area() function is not needed
as all the memory above boot memory size must be preserved anyway. Update
the function by dropping this redundant parameter.
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/156821374440.5656.2945512543806951766.stgit@hbathini.in.ibm.com
|
|
Commit 0962e8004e97 ("powerpc/prom: Scan reserved-ranges node for
memory reservations") enabled support to parse 'reserved-ranges' DT
node to reserve kernel memory falling in these ranges for firmware
purposes. Along with the preserved area memory, ensure memory in
reserved ranges is not overlapped with memory released by capture
kernel aftering saving vmcore. Also, fix the off-by-one error in
fadump_release_reserved_area function while releasing memory.
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/156821371358.5656.6061214942558818661.stgit@hbathini.in.ibm.com
|
|
Make allocate_crash_memory_ranges() and free_crash_memory_ranges()
functions generic to reuse them for memory management of all types of
dynamic memory range arrays. This change helps in memory management
of reserved ranges array to be added later.
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/156821369863.5656.4375667005352155892.stgit@hbathini.in.ibm.com
|
|
Firmware provides architected register state data at the time of crash.
Process this data and build CPU notes to append to ELF core. In case
this data is missing or in unsupported format, at least append crashing
CPU's register data, to have something to work with in the vmcore file.
Signed-off-by: Hari Bathini <hbathini@linux.vnet.ibm.com>
Signed-off-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/156821367702.5656.5546683836236508389.stgit@hbathini.in.ibm.com
|
|
Earlier, memblock_find_in_range() was not used to find the memory to
be reserved for FADump as bottom up allocation mode was not supported.
But since commit 79442ed189acb8b ("mm/memblock.c: introduce bottom-up
allocation mode") bottom up allocation mode is supported for memblock.
So, use it to find the memory to be reserved for FADump.
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/156821364211.5656.14336025460336135194.stgit@hbathini.in.ibm.com
|
|
With FADump support now available on both pseries and OPAL platforms,
update FADump documentation with these details.
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/156821361692.5656.11377757995827253404.stgit@hbathini.in.ibm.com
|
|
Make OPAL call to indicate that the dump is processed and the metadata
area in OPAL can be cleared/released. Also, setup/initialize FADump
for re-registration.
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/156821356046.5656.12270927048195494911.stgit@hbathini.in.ibm.com
|
|
If all kernel boot memory regions are not registered for MPIPL before
system crashes, try processing the partial crashdump but warn the user
before proceeding.
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/156821352793.5656.1734051341024721407.stgit@hbathini.in.ibm.com
|
|
Add support in the kernel to process the crash'ed kernel's memory
preserved during MPIPL and export it as /proc/vmcore file for the
userland scripts to filter and analyze it later.
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/156821351482.5656.6255805804744333073.stgit@hbathini.in.ibm.com
|
|
Firmware uses a 32-bit field for size while copying/backing-up memory
during MPIPL. So, the maximum value that could be represented with
a PAGE_SIZE aligned 32-bit field will be the maximum copy size for a
region but FADump capture kernel usually needs more memory than that
to be preserved to avoid running into out of memory errors.
So, request firmware to copy multiple kernel boot memory regions
instead of just one (which worked fine for pseries as 64-bit field
was used for size there).
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/156821350193.5656.3664853158523582019.stgit@hbathini.in.ibm.com
|
|
Make OPAL calls to register and un-register with firmware for MPIPL.
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/156821348482.5656.13646250851483648241.stgit@hbathini.in.ibm.com
|
|
During kexec boot, metadata address needs to be reset to avoid running
into errors interpreting stale metadata address, in case the kexec'ed
kernel crashes before metadata address could be setup again.
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/156821346629.5656.10783321582005237813.stgit@hbathini.in.ibm.com
|
|
OPAL allows registering address with it in the first kernel and
retrieving it after MPIPL. Setup kernel metadata and register its
address with OPAL to use it for processing the crash dump.
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/156821345011.5656.13567765019032928471.stgit@hbathini.in.ibm.com
|
|
Some code clean-up like using minimal assignments and updating printk
messages. Also, add an 'error_out' label for handling error cleanup
at one place.
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/156821343485.5656.10202857091553646948.stgit@hbathini.in.ibm.com
|
|
Add basic callback functions for FADump on PowerNV platform.
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/156821342072.5656.4346362203141486452.stgit@hbathini.in.ibm.com
|
|
MPIPL is Memory Preserving IPL supported from POWER9. This enables the
kernel to reset the system with memory 'preserved'. Also, it supports
copying memory from a source address to some destination address during
MPIPL boot. Add MPIPL interface definitions here to leverage these f/w
features in adding FADump support for PowerNV platform.
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/156821340710.5656.10071829040515662624.stgit@hbathini.in.ibm.com
|
|
fadump is pronounced f-a-dump. Update documentation accordingly. Also,
update how fadump_region contents look like with recent changes.
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/156821339317.5656.15852294223821732082.stgit@hbathini.in.ibm.com
|
|
Move code that supports processing the crash'ed kernel's memory
preserved by firmware to platform specific callback functions.
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/156821337690.5656.13050665924800177744.stgit@hbathini.in.ibm.com
|
|
Except for Reserved dump area (see Documentation/powerpc/firmware-
assisted-dump.rst) which is permanent reserved, all memory above boot
memory size, where boot memory size is the memory required for the
kernel to boot successfully when booted with restricted memory (memory
for capture kernel), is released when the dump is invalidated. Make
this a bit more explicit in the code.
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/156821336092.5656.1079046285366041687.stgit@hbathini.in.ibm.com
|
|
Improve how fadump_region contents are displayed by adding source
information of memory regions that are to be dumped by f/w.
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/156821334740.5656.5897097884010195405.stgit@hbathini.in.ibm.com
|
|
Move platform specific register/un-register code, the RTAS calls, to
register/un-register callback functions. This would also mean moving
code that initializes and prints the platform specific FADump data.
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Reviewed-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/156821332856.5656.16380417702046411631.stgit@hbathini.in.ibm.com
|
