| Age | Commit message (Collapse) | Author |
|---|
|
Previous patch added the ability to offload a VXLAN tunnel used for L3
VNI when it is present in the VLAN-aware bridge before the corresponding
VLAN interface is configured. This patch adds a test case to verify
that.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In symmetric routing, the only two members in the VLAN corresponding to
the L3 VNI are the router port and the VXLAN tunnel.
In case the VXLAN device is already enslaved to the bridge and only
later the VLAN interface is configured, the tunnel will not be
offloaded.
The reason for this is that when the router interface (RIF)
corresponding to the VLAN interface is configured, it calls the core
fid_get() API which does not check if NVE should be enabled on the FID.
Instead, call into the bridge code which will check if NVE should be
enabled on the FID.
This effectively means that the same code path is used to retrieve a FID
when either a local port or a router port joins the FID.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We have no explicit signal when a UDP stream has terminated, peers just
stop sending.
For suspected stream connections a timeout of two minutes is sane to keep
NAT mapping alive a while longer.
It matches tcp conntracks 'timewait' default timeout value.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Currently DNS resolvers that send both A and AAAA queries from same source port
can trigger stream mode prematurely, which results in non-early-evictable conntrack entry
for three minutes, even though DNS requests are done in a few milliseconds.
Add a two second grace period where we continue to use the ordinary
30-second default timeout. Its enough for DNS request/response traffic,
even if two request/reply packets are involved.
ASSURED is still set, else conntrack (and thus a possible
NAT mapping ...) gets zapped too in case conntrack table runs full.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2018-12-20
This series contains updates to e100, igb, ixgbe, i40e and ice drivers.
I replaced spinlocks for mutex locks to reduce the latency on CPU0 for
igb when updating the statistics. This work was based off a patch
provided by Jan Jablonsky, which was against an older version of the igb
driver.
Jesus adjusts the receive packet buffer size from 32K to 30K when
running in QAV mode, to stay within 60K for total packet buffer size for
igb.
Vinicius adds igb kernel documentation regarding the CBS algorithm and
its implementation in the i210 family of NICs.
YueHaibing from Huawei fixed the e100 driver that was potentially
passing a NULL pointer, so use the kernel macro IS_ERR_OR_NULL()
instead.
Konstantin Khorenko fixes i40e where we were not setting up the
neigh_priv_len in our net_device, which caused the driver to read beyond
the neighbor entry allocated memory.
Miroslav Lichvar extends the PTP gettime() to read the system clock by
adding support for PTP_SYS_OFFSET_EXTENDED ioctl in i40e.
Young Xiao fixed the ice driver to only enable NAPI on q_vectors that
actually have transmit and receive rings.
Kai-Heng Feng fixes an igb issue that when placed in suspend mode, the
NIC does not wake up when a cable is plugged in. This was due to the
driver not setting PME during runtime suspend.
Stephen Douthit enables the ixgbe driver allow DSA devices to use the
MII interface to talk to switches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On NVMe offloads connection with many IO queues, EEH takes long time to
recover. The culprit is the synchronize_srcu in the destroy_mkey. The
solution is to use synchronize_srcu only for ODP mkey.
Fixes: b4cfe447d47b ("IB/mlx5: Implement on demand paging by adding support for MMU notifiers")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"I2C has a MAINTAINERS update for you, so people will be immediately
pointed to the right person for this previously orphaned driver.
And one of Arnd's build warning fixes for a new driver added this
cycle"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: nvidia-gpu: mark resume function as __maybe_unused
MAINTAINERS: add entry for i2c-axxia driver
|
|
John Fastabend says:
====================
Set of bpf fixes and improvements to make sockmap with kTLS usable
with "real" applications. This set came as the fallout of pulling
kTLS+sockmap into Cilium[1] and running in container environment.
Roughly broken into three parts,
Patches 1-3: resolve/improve handling of size field in sk_msg_md
Patch 4: it became difficult to use this in Cilium when the
SK_PASS verdict was not correctly handle. So handle
the case correctly.
Patch 5-8: Set of issues found while running OpenSSL TX kTLS
enabled applications. This resolves the most obvious
issues and gets applications using kTLS TX up and
running with sock{map|has}.
Other than the "sk_msg, zap ingress queue on psock down" (PATCH 6/8)
which can potentially cause a WARNING the issues fixed in this
series do not cause kernel side warnings, BUG, etc. but instead
cause stalls and other odd behavior in the user space applications
when using kTLS with BPF policies applied.
Primarily tested with 'curl' compiled with latest openssl and
also 'openssl s_client/s_server' containers using Cilium network
plugin with docker/k8s. Some basic testing with httpd was also
enabled. Cilium CI tests will be added shortly to cover these
cases as well. We also have 'wrk' and other test and benchmarking
tools we can run now.
We have two more sets of patches currently under testing that
will be sent shortly to address a few more issues. First the
OpenSSL RX kTLS side breaks when both sk_msg and sk_skb_verdict
programs are used with kTLS, the sk_skb_verdict programs are
not enforced. Second skmsg needs to call into tcp stack to
send to indicate consumed data.
====================
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
The existing code did not expect users would initialize the TLS ULP
without subsequently calling the TLS TX enabling socket option.
If the application tries to send data after the TLS ULP enable op
but before the TLS TX enable op the BPF sk_msg verdict program is
skipped. This patch resolves this by converting the ipv4 sock ops
to be calculated at init time the same way ipv6 ops are done. This
pulls in any changes to the sock ops structure that have been made
after the socket was created including the changes from adding the
socket to a sock{map|hash}.
This was discovered by running OpenSSL master branch which calls
the TLS ULP setsockopt early in TLS handshake but only enables
the TLS TX path once the handshake has completed. As a result the
datapath missed the initial handshake messages.
Fixes: 02c558b2d5d6 ("bpf: sockmap, support for msg_peek in sk_msg with redirect ingress")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
A sockmap program that redirects through a kTLS ULP enabled socket
will not work correctly because the ULP layer is skipped. This
fixes the behavior to call through the ULP layer on redirect to
ensure any operations required on the data stream at the ULP layer
continue to be applied.
To do this we add an internal flag MSG_SENDPAGE_NOPOLICY to avoid
calling the BPF layer on a redirected message. This is
required to avoid calling the BPF layer multiple times (possibly
recursively) which is not the current/expected behavior without
ULPs. In the future we may add a redirect flag if users _do_
want the policy applied again but this would need to work for both
ULP and non-ULP sockets and be opt-in to avoid breaking existing
programs.
Also to avoid polluting the flag space with an internal flag we
reuse the flag space overlapping MSG_SENDPAGE_NOPOLICY with
MSG_WAITFORONE. Here WAITFORONE is specific to recv path and
SENDPAGE_NOPOLICY is only used for sendpage hooks. The last thing
to verify is user space API is masked correctly to ensure the flag
can not be set by user. (Note this needs to be true regardless
because we have internal flags already in-use that user space
should not be able to set). But for completeness we have two UAPI
paths into sendpage, sendfile and splice.
In the sendfile case the function do_sendfile() zero's flags,
./fs/read_write.c:
static ssize_t do_sendfile(int out_fd, int in_fd, loff_t *ppos,
size_t count, loff_t max)
{
...
fl = 0;
#if 0
/*
* We need to debate whether we can enable this or not. The
* man page documents EAGAIN return for the output at least,
* and the application is arguably buggy if it doesn't expect
* EAGAIN on a non-blocking file descriptor.
*/
if (in.file->f_flags & O_NONBLOCK)
fl = SPLICE_F_NONBLOCK;
#endif
file_start_write(out.file);
retval = do_splice_direct(in.file, &pos, out.file, &out_pos, count, fl);
}
In the splice case the pipe_to_sendpage "actor" is used which
masks flags with SPLICE_F_MORE.
./fs/splice.c:
static int pipe_to_sendpage(struct pipe_inode_info *pipe,
struct pipe_buffer *buf, struct splice_desc *sd)
{
...
more = (sd->flags & SPLICE_F_MORE) ? MSG_MORE : 0;
...
}
Confirming what we expect that internal flags are in fact internal
to socket side.
Fixes: d3b18ad31f93 ("tls: add bpf support to sk_msg handling")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
In addition to releasing any cork'ed data on a psock when the psock
is removed we should also release any skb's in the ingress work queue.
Otherwise the skb's eventually get free'd but late in the tear
down process so we see the WARNING due to non-zero sk_forward_alloc.
void sk_stream_kill_queues(struct sock *sk)
{
...
WARN_ON(sk->sk_forward_alloc);
...
}
Fixes: 604326b41a6f ("bpf, sockmap: convert to generic sk_msg interface")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
When a skb verdict program is in-use and either another BPF program
redirects to that socket or the new SK_PASS support is used the
data_ready callback does not wake up application. Instead because
the stream parser/verdict is using the sk data_ready callback we wake
up the stream parser/verdict block.
Fix this by adding a helper to check if the stream parser block is
enabled on the sk and if so call the saved pointer which is the
upper layers wake up function.
This fixes application stalls observed when an application is waiting
for data in a blocking read().
Fixes: d829e9c4112b ("tls: convert to generic sk_msg interface")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Add SK_PASS verdict support to SK_SKB_VERDICT programs. Now that
support for redirects exists we can implement SK_PASS as a redirect
to the same socket. This simplifies the BPF programs and avoids an
extra map lookup on RX path for simple visibility cases.
Further, reduces user (BPF programmer in this context) confusion
when their program drops skb due to lack of support.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Enforce comment on structure layout dependency with a BUILD_BUG_ON
to ensure the condition is maintained.
Suggested-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
The check for max offset in sk_msg_is_valid_access uses sizeof()
which is incorrect because it would allow accessing possibly
past the end of the struct in the padded case. Further, it doesn't
preclude accessing any padding that may be added in the middle of
a struct. All told this makes it fragile to rely on.
To fix this explicitly check offsets with fields using the
bpf_ctx_range() and bpf_ctx_range_till() macros.
For reference the current structure layout looks as follows (reported
by pahole)
struct sk_msg_md {
union {
void * data; /* 8 */
}; /* 0 8 */
union {
void * data_end; /* 8 */
}; /* 8 8 */
__u32 family; /* 16 4 */
__u32 remote_ip4; /* 20 4 */
__u32 local_ip4; /* 24 4 */
__u32 remote_ip6[4]; /* 28 16 */
__u32 local_ip6[4]; /* 44 16 */
__u32 remote_port; /* 60 4 */
/* --- cacheline 1 boundary (64 bytes) --- */
__u32 local_port; /* 64 4 */
__u32 size; /* 68 4 */
/* size: 72, cachelines: 2, members: 10 */
/* last cacheline: 8 bytes */
};
So there should be no padding at the moment but fixing this now
prevents future errors.
Reported-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Currently, the test to ensure reads past the end of the sk_msg_md
data structure fail is incorrectly expecting success. Fix this
typo and use correct expected error.
Fixes: 945a47d87cee ("bpf: sk_msg, add tests for size field")
Reported-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Use 3-byte 'nop' and 'j' instructions that are always present. Don't let
assembler mark a spot right after patchable 'j' instruction as
unreachable and later put literals or padding bytes there. Add separate
implementations of patch_text for SMP and UP cases, avoiding use of
atomics on UP.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
|
|
The frame_size passed to build_skb must be aligned, else it is
possible that the embedded struct skb_shared_info gets unaligned.
For correctness make sure that xdpf->headroom in included in the
alignment. No upstream drivers can hit this, as all XDP drivers provide
an aligned headroom. This was discovered when playing with implementing
XDP support for mvneta, which have a 2 bytes DSA header, and this
Marvell ARM64 platform didn't like doing atomic operations on an
unaligned skb_shinfo(skb)->dataref addresses.
Fixes: 1c601d829ab0 ("bpf: cpumap xdp_buff to skb conversion and allocation")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
When dealing with netdev unregister events, we just need to know that this
is our currently bounded netdev. There's no need to do any further
checks/queries.
This patch doesn't change any functionality.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Add a method for query port under the uverbs global methods. Current
ib_port_attr struct is passed as a single attribute and port_cap_flags2 is
added as a new attribute to the function.
Signed-off-by: Michael Guralnik <michaelgur@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
port_cap_flags2 represents IBTA PortInfo:CapabilityMask2.
The field safely extends the RDMA_NLDEV_ATTR_CAP_FLAGS operand as it was
exported as 64 bit to allow this kind of extension.
Signed-off-by: Michael Guralnik <michaelgur@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Add a helper to zero fill fields before copying data to
UVERBS_ATTR_STRUCT.
As UVERBS_ATTR_STRUCT can be used as an extensible struct, we want to make
sure that if the user supplies us with a struct that has new fields that
we are not aware of, we return them zeroed to the user.
This helper should be used when using UVERBS_ATTR_STRUCT for an extendable
data structure and there is a need to make sure that extended members of
the struct, that the kernel doesn't handle, are returned zeroed to the
user. This is needed due to the fact that UVERBS_ATTR_STRUCT allows
non-zero values for members after 'last' member.
Signed-off-by: Michael Guralnik <michaelgur@mellanox.com>
Reviewed-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Pull UBI/UBIFS fixes from Richard Weinberger:
- Kconfig dependency fixes for our new auth feature
- Fix for selecting the right compressor when creating a fs
- Bugfix for a bug in UBIFS's O_TMPFILE implementation
- Refcounting fixes for UBI
* tag 'upstream-4.20-rc7' of git://git.infradead.org/linux-ubifs:
ubifs: Handle re-linking of inodes correctly while recovery
ubi: Do not drop UBI device reference before using
ubi: Put MTD device after it is not used
ubifs: Fix default compression selection in ubifs
ubifs: Fix memory leak on error condition
ubifs: auth: Add CONFIG_KEYS dependency
ubifs: CONFIG_UBIFS_FS_AUTHENTICATION should depend on UBIFS_FS
ubifs: replay: Fix high stack usage
|
|
Document properties reg and interrupts for OMAP GPIO controller bindings
Also add unit address in node name of the example
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
s/whold/whole/.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Same code is executed in both rxe_param_set_add and rxe_notify functions.
Make one function and call it from both places.
Since both callers already have a rxe object use it directly instead of
deriving it from the net device.
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Current rxe device counters are not thread safe.
When multiple QPs are used, they can be racy.
Make them thread safe by making it atomic64.
Fixes: 0b1e5b99a48b ("IB/rxe: Add port protocol stats")
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
During testing the command format was changed to close a security
hole. Revise the driver to use the command format that will actually be
supported in GA firmware.
Both the UMEM and UCTX are intended only for use by the kernel and cannot
be executed using a general command.
Since the UMEM and CTX are not part of the general object the caps bits
were moved to be some log_xxx location in the general HCA caps.
The firmware code was adapted as well to match the above.
Fixes: a8b92ca1b0e5 ("IB/mlx5: Introduce DEVX")
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Reviewed-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Use uid as part of alloc/dealloc transport domain to let firmware manages
the resources correctly.
Fixes: d2d19121ae2f ("IB/mlx5: Set uid as part of TD commands")
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Reviewed-by: Artemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Clang warns:
drivers/acpi/tables.c:715:14: warning: unused variable 'amlcode'
[-Wunused-variable]
static void *amlcode __attribute__ ((weakref("AmlCode")));
^
drivers/acpi/tables.c:716:14: warning: unused variable 'dsdt_amlcode'
[-Wunused-variable]
static void *dsdt_amlcode __attribute__ ((weakref("dsdt_aml_code")));
^
2 warnings generated.
The only uses of these variables are hiddem behind CONFIG_ACPI_CUSTOM_DSDT
so do the same thing here.
Fixes: 82e4eb4e9653 (ACPI / tables: add DSDT AmlCode new declaration name support)
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
In __ghes_panic() clear the block status in the APEI generic
error status block for that generic hardware error source before
calling panic() to prevent a second panic() in the crash kernel
for exactly the same fatal error.
Otherwise ghes_probe(), running in the crash kernel, would see
an unhandled error in the APEI generic error status block and
panic again, thereby precluding any crash dump.
Signed-off-by: Lenny Szubowicz <lszubowi@redhat.com>
Signed-off-by: David Arcari <darcari@redhat.com>
Tested-by: Tyler Baicar <baicar.tyler@gmail.com>
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
From git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
mlx5 updates taken for dependencies on following patches.
* branche 'mlx5-next': (23 commits)
IB/mlx5: Introduce uid as part of alloc/dealloc transport domain
net/mlx5: Add shared Q counter bits
net/mlx5: Continue driver initialization despite debugfs failure
net/mlx5: Fold the modify lag code into function
net/mlx5: Add lag affinity info to log
net/mlx5: Split the activate lag function into two routines
net/mlx5: E-Switch, Introduce flow counter affinity
IB/mlx5: Unify e-switch representors load approach between uplink and VFs
net/mlx5: Use lowercase 'X' for hex values
net/mlx5: Remove duplicated include from eswitch.c
net/mlx5: Remove the get protocol device interface entry
net/mlx5: Support extended destination format in flow steering command
net/mlx5: E-Switch, Change vhca id valid bool field to bit flag
net/mlx5: Introduce extended destination fields
net/mlx5: Revise gre and nvgre key formats
net/mlx5: Add monitor commands layout and event data
net/mlx5: Add support for plugged-disabled cable status in PME
net/mlx5: Add support for PCIe power slot exceeded error in PME
net/mlx5: Rework handling of port module events
net/mlx5: Move flow counters data structures from flow steering header
...
|
|
Use the mii_bus callbacks to address the entire clause 22/45 address
space. Enables userspace to poke switch registers instead of a single
PHY address.
The ixgbe firmware may be polling PHYs in a way that is not protected by
the mii_bus lock. This isn't new behavior, but as Andrew Lunn pointed
out there are more addresses available for conflicts.
Signed-off-by: Stephen Douthit <stephend@silicom-usa.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Most dsa devices expect a 'struct mii_bus' pointer to talk to switches
via the MII interface.
While this works for dsa devices, it will not work safely with Linux
PHYs in all configurations since the firmware of the ixgbe device may
be polling some PHY addresses in the background.
Signed-off-by: Stephen Douthit <stephend@silicom-usa.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
I210 ethernet card doesn't wakeup when a cable gets plugged. It's
because its PME is not set.
Since commit 42eca2302146 ("PCI: Don't touch card regs after runtime
suspend D3"), if the PCI state is saved, pci_pm_runtime_suspend() stops
calling pci_finish_runtime_suspend(), which enables the PCI PME.
To fix the issue, let's not to save PCI states when it's runtime
suspend, to let the PCI subsystem enables PME.
Fixes: 42eca2302146 ("PCI: Don't touch card regs after runtime suspend D3")
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
If ice driver has q_vectors w/ active NAPI that has no rings,
then this will result in a divide by zero error. To correct it
I am updating the driver code so that we only support NAPI on
q_vectors that have 1 or more rings allocated to them.
See commit 13a8cd191a2b ("i40e: Do not enable NAPI on q_vectors
that have no rings") for detail.
Signed-off-by: Young Xiao <YangX92@hotmail.com>
Acked-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This adds support for the PTP_SYS_OFFSET_EXTENDED ioctl.
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Out of bound read reported by KASan.
i40iw_net_event() reads unconditionally 16 bytes from
neigh->primary_key while the memory allocated for
"neighbour" struct is evaluated in neigh_alloc() as
tbl->entry_size + dev->neigh_priv_len
where "dev" is a net_device.
But the driver does not setup dev->neigh_priv_len and
we read beyond the neigh entry allocated memory,
so the patch in the next mail fixes this.
Signed-off-by: Konstantin Khorenko <khorenko@virtuozzo.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Fix a static code checker warning:
drivers/net/ethernet/intel/e100.c:1349
e100_load_ucode_wait() warn: passing zero to 'PTR_ERR'
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Lots of conflicts, by happily all cases of overlapping
changes, parallel adds, things of that nature.
Thanks to Stephen Rothwell, Saeed Mahameed, and others
for their guidance in these resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add some pointers to the definition of the CBS algorithm, and some
notes about the limits of its implementation in the i210 family of
controllers.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Section 4.5.9 of the datasheet says that the total size of all packet
buffers combined (TxPB 0 + 1 + 2 + 3 + RxPB + BMC2OS + OS2BMC) must not
exceed 60KB. Today we are configuring a total of 62KB, so reduce the
RxPB from 32KB to 30KB in order to respect that.
The choice of changing RxPBSIZE here is mainly because it seems more
correct to give more priority to the transmit packet buffers over the
receiver ones when running in Qav mode. Also, the BMC2OS and OS2BMC
sizes are already too short.
Signed-off-by: Jesus Sanchez-Palencia <jesus.s.palencia@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
sbq_wake_ptr() checks sbq->ws_active to know if it needs to loop
the wait indexes or not. This requires the use of the sbitmap
waitqueue wrappers, but kyber doesn't use those for its domain
token waitqueue handling.
Convert kyber to use the helpers. This fixes a hang with waiting
for domain tokens.
Fixes: 5d2ee7122c73 ("sbitmap: optimize wakeup check")
Tested-by: Ming Lei <ming.lei@redhat.com>
Reported-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
After commit 5d2ee7122c73, users of sbitmap that need wait queue
handling must use the provided helpers. But we only added
prepare_to_wait()/finish_wait() style helpers, add the equivalent
add_wait_queue/list_del wrappers as we..
This is needed to ensure kyber plays by the sbitmap waitqueue
rules.
Tested-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
This change is based off of the work and suggestion of Jan Jablonsky
<jan.jablonsky@thalesgroup.com>.
The Watchdog workqueue in igb driver is scheduled every 2s for each
network interface. That includes updating a statistics protected by
spinlock. Function igb_update_stats in this case will be protected
against preemption. According to number of a statistics registers
(cca 60), processing this function might cause additional cpu load
on CPU0.
In case of statistics spinlock may be replaced with mutex, which
reduce latency on CPU0.
CC: Bernhard Kaindl <bernhard.kaindl@thalesgroup.com>
CC: Jan Jablonsky <jan.jablonsky@thalesgroup.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Mapping the delay slot emulation page as both writeable & executable
presents a security risk, in that if an exploit can write to & jump into
the page then it can be used as an easy way to execute arbitrary code.
Prevent this by mapping the page read-only for userland, and using
access_process_vm() with the FOLL_FORCE flag to write to it from
mips_dsemul().
This will likely be less efficient due to copy_to_user_page() performing
cache maintenance on a whole page, rather than a single line as in the
previous use of flush_cache_sigtramp(). However this delay slot
emulation code ought not to be running in any performance critical paths
anyway so this isn't really a problem, and we can probably do better in
copy_to_user_page() anyway in future.
A major advantage of this approach is that the fix is small & simple to
backport to stable kernels.
Reported-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: 432c6bacbd0c ("MIPS: Use per-mm page to execute branch delay slot instructions")
Cc: stable@vger.kernel.org # v4.8+
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Rich Felker <dalias@libc.org>
Cc: David Daney <david.daney@cavium.com>
|
|
In commit 4f83d5ea643a ("security: integrity: make ima_main explicitly
non-modular") I'd removed <linux/module.h> after assuming that the
function is_module_sig_enforced() was an LSM function and not a core
kernel module function.
Unfortunately the typical .config selections used in build testing
provide an implicit <linux/module.h> presence, and so normal/typical
build testing did not immediately reveal my incorrect assumption.
Cc: Mimi Zohar <zohar@linux.vnet.ibm.com>
Cc: Dmitry Kasatkin <dmitry.kasatkin@gmail.com>
Cc: James Morris <james.l.morris@oracle.com>
Cc: "Serge E. Hallyn" <serge@hallyn.com>
Cc: linux-ima-devel@lists.sourceforge.net
Cc: linux-security-module@vger.kernel.org
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/core
Pull perf/core improvements and fixes from Arnaldo Carvalho de Melo:
- Implement BPF based syscall filtering in 'perf trace', using BPF maps and
the augmented_raw_syscalls.c BPF proggie (Arnaldo Carvalho de Melo)
- Allow specifying in .perfconfig a set of events use in 'perf trace' in
addition to any other specified from the command line. This initially
will be used to always use the augmented_raw_syscalls.o precompiled
BPF program for getting pointer contents. (Arnaldo Carvalho de Melo)
- Allow fine grained control about how the syscall output should be
formatted. This will be used to allow producing the same output produced
by the 'strace' tool, to then use in regression tests comparing the
output of 'perf trace' with the one produced from 'strace' (Arnaldo Carvalho de Melo)
- Beautify the renameat2 olddirfd, newdirfd and flags arguments (Arnaldo Carvalho de Melo)
- Beautify arch_prctl 'code' syscall arg (Arnaldo Carvalho de Melo)
- Beautify fadvise64 'advice' syscall arg (Arnaldo Carvalho de Melo)
- Relax checks on perf-PID.map ownership, resulting in symbols in
executable anonymous maps setup by JITs in things like node.js to
be resolved in a 'perf top' session run by root without the need
for --force to be used (Arnaldo Carvalho de Melo)
- Update asm-generic/unistd.h copy (Arnaldo Carvalho de Melo)
- Do not use the first and last symbols when setting up address filters in
auxtrace, this fails when we don't have a symbol table, filter the entire
area based on the dso size. (Adrian Hunter)
- Do not use kernel headers to build libsubcmd, we shouldn't use
anything from outside tools/, fixes the build with the Android NDK (Arnaldo Carvalho de Melo)
- Add several prototypes for systems lacking those, such as open_memstream(),
sigqueue(), fixing warnings building with Android's bionic libc that were
preventing the use of -Werror there (Arnaldo Carvalho de Melo)
- Use LDFLAGS in the libtraceevent build commands, allowing developers
to override its values (Jiri Olsa)
- Link libperf-jvmti.so with LDFLAGS variable, allowing distro
packages to propagate its settings when building this library (Jiri Olsa)
- cs-etm (ARM CoreSight) fixes: (Leo Yan)
- Correct packets swapping in cs_etm__flush()
- Avoid stale branch samples when flush packet
- Remove unused 'trace_on' in cs_etm_decoder
- Refactor enumeration cs_etm_sample_type
- Rename CS_ETM_TRACE_ON to CS_ETM_DISCONTINUITY
- Treat NO_SYNC element as trace discontinuity
- Treat EO_TRACE element as trace discontinuity
- Generate branch sample for exception packet
- Use shebangs in the 'perf test' shell scripts, making them identifiable as
shell scripts (Michael Petlan)
- Avoid segfaults caused by negated options in 'perf stat' (Michael Petlan)
- Fix processing of dereferenced args in bprintk events in libtracevent (Steven Rostedt)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
ath.git patches for 4.21. Major changes:
ath10k
* add amsdu support for QCA6174 monitor mode
* report tx rate using the new ieee80211_tx_rate_update() API
* wcn3990 support is not experimental anymore
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
Fix spectre v1 vuln in drm_ioctl
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20181220165740.GA42344@art_vandelay
|
