| Age | Commit message (Collapse) | Author |
|---|
|
If there are packets in hardware when changing the speed
or duplex, it may cause hardware hang up.
This patch adds the code for waiting chip to clean the all
pkts(TX & RX) in chip when the driver uses the function named
"adjust link".
This patch cleans the pkts as follows:
1) close rx of chip, close tx of protocol stack.
2) wait rcb, ppe, mac to clean.
3) adjust link
4) open rx of chip, open tx of protocol stack.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I have two Ethernet adapters:
r8169 0000:03:01.0 eth0: RTL8169sb/8110sb, 00:14:d1:14:2d:49, XID 10000000, IRQ 18
r8169 0000:01:00.0 eth0: RTL8168e/8111e, 64:66:b3:11:14:5d, XID 2c200000, IRQ 30
And after upgrading from linux 4.15 [1] to linux 4.18+ [2] RTL8169sb failed to
receive any packets. tcpdump shows a lot of checksum mismatch.
[1]: a0f79386a4968b4925da6db2d1daffd0605a4402
[2]: 0519359784328bfa92bf0931bf0cff3b58c16932 (4.19 merge window opened)
I started bisecting and the found that [3] breaks it. According to [4]:
"For 8110S, 8110SB, and 8110SC series, the initial value of RxConfig
needs to be set after the tx/rx is enabled."
So I moved rtl_init_rxcfg() after enabling tx/rs and now my adapter works
(RTL8168e works too).
[3]: 3559d81e76bfe3803e89f2e04cf6ef7ab4f3aace
[4]: e542a2269f232d61270ceddd42b73a4348dee2bb ("r8169: adjust the RxConfig
settings.")
Also drop "rx" from rtl_set_rx_tx_config_registers(), since it does nothing
with it already.
Fixes: 3559d81e76bfe3803e89f2e04cf6ef7ab4f3aace ("r8169: simplify
rtl_hw_start_8169")
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
Signed-off-by: Azat Khuzhin <a3at.mail@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
syzbot reported a use-after-free in tipc_group_fill_sock_diag(),
where tipc_group_fill_sock_diag() still reads tsk->group meanwhile
tipc_group_delete() just deletes it in tipc_release().
tipc_nl_sk_walk() aims to lock this sock when walking each sock
in the hash table to close race conditions with sock changes like
this one, by acquiring tsk->sk.sk_lock.slock spinlock, unfortunately
this doesn't work at all. All non-BH call path should take
lock_sock() instead to make it work.
tipc_nl_sk_walk() brutally iterates with raw rht_for_each_entry_rcu()
where RCU read lock is required, this is the reason why lock_sock()
can't be taken on this path. This could be resolved by switching to
rhashtable iterator API's, where taking a sleepable lock is possible.
Also, the iterator API's are friendly for restartable calls like
diag dump, the last position is remembered behind the scence,
all we need to do here is saving the iterator into cb->args[].
I tested this with parallel tipc diag dump and thousands of tipc
socket creation and release, no crash or memory leak.
Reported-by: syzbot+b9c8f3ab2994b7cd1625@syzkaller.appspotmail.com
Cc: Jon Maloy <jon.maloy@ericsson.com>
Cc: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 4ae0169fd1b3c792b66be58995b7e6b629919ecf.
This change in the handling of the coalesce timer is causing regression on
(at least) amlogic platforms.
Network will break down very quickly (a few seconds) after starting
a download. This can easily be reproduced using iperf3 for example.
The problem has been reported on the S805, S905, S912 and A113 SoCs
(Realtek and Micrel PHYs) and it is likely impacting all Amlogics
platforms using Gbit ethernet
No problem was seen with the platform using 10/100 only PHYs (GXL internal)
Reverting change brings things back to normal and allows to use network
again until we better understand the problem with the coalesce timer.
Cc: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Vitor Soares <soares@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
rhashtable_walk_exit() must be paired with rhashtable_walk_enter().
Fixes: 40f9f4397060 ("tipc: Fix tipc_sk_reinit race conditions")
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before the commit d6990976af7c ("vti6: fix PMTU caching and reporting
on xmit") '!skb->ignore_df' check was always true because the function
skb_scrub_packet() was called before it, resetting ignore_df to zero.
In the commit, skb_scrub_packet() was moved below, and now this check
can be false for the packet, e.g. when sending it in the two fragments,
this prevents successful PMTU updates in such case. The next attempts
to send the packet lead to the same tx error. Moreover, vti6 initial
MTU value relies on PMTU adjustments.
This issue can be reproduced with the following LTP test script:
udp_ipsec_vti.sh -6 -p ah -m tunnel -s 2000
Fixes: ccd740cbc6e0 ("vti6: Add pmtu handling to vti6_xmit.")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Daniel Borkmann says:
====================
pull-request: bpf 2018-08-29
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix a build error in sk_reuseport_convert_ctx_access() when
compiling with clang which cannot resolve hweight_long() at
build time inside the BUILD_BUG_ON() assertion, from Stefan.
2) Several fixes for BPF sockmap, four of them in getting the
bpf_msg_pull_data() helper to work, one use after free case
in bpf_tcp_close() and one refcount leak in bpf_tcp_recvmsg(),
from Daniel.
3) Another fix for BPF sockmap where we misaccount sk_mem_uncharge()
in the socket redirect error case from unwinding scatterlist
twice, from John.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The newly added code that emits ksymtab entries as pairs of 32-bit
relative references interacts poorly with the way powerpc lays out its
address space: when a module exports a per-CPU variable, the primary
module region covering the ksymtab entry -and thus the 32-bit relative
reference- is too far away from the actual per-CPU variable's base
address (to which the per-CPU offsets are applied to obtain the
respective address of each CPU's copy), resulting in corruption when the
module loader attempts to resolve symbol references of modules that are
loaded on top and link to the exported per-CPU symbol.
So let's disable this feature on powerpc. Even though it implements
CONFIG_RELOCATABLE, it does not implement CONFIG_RANDOMIZE_BASE and so
KASLR kernels (which are the main target of the feature) do not exist on
powerpc anyway.
Reported-by: Andreas Schwab <schwab@linux-m68k.org>
Suggested-by: Nicholas Piggin <nicholas.piggin@gmail.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
- Fix potential Spectre v1 in nct6775
- Add error checking to adt7475 driver
- Fix reading shunt resistor value in ina2xx driver
* tag 'hwmon-for-linus-v4.19-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (nct6775) Fix potential Spectre v1
hwmon: (adt7475) Make adt7475_read_word() return errors
hwmon: (adt7475) Potential error pointer dereferences
hwmon: (ina2xx) fix sysfs shunt resistor read access
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs
Pull misc fs fixes from Jan Kara:
- make UDF to properly mount media created by Win7
- make isofs to properly refuse devices with large physical block size
- fix a Spectre gadget in quotactl(2)
- fix a warning in fsnotify code hit by syzkaller
* tag 'for_v4.19-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
udf: Fix mounting of Win7 created UDF filesystems
udf: Remove dead code from udf_find_fileset()
fs/quota: Fix spectre gadget in do_quotactl
fs/quota: Replace XQM_MAXQUOTAS usage with MAXQUOTAS
isofs: reject hardware sector size > 2048 bytes
fsnotify: fix false positive warning on inode delete
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lftan/nios2
Pull nios2 fix from Ley Foon Tan:
"remove duplicate DEBUG_STACK_USAGE symbol defintions"
* tag 'nios2-v4.19-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/lftan/nios2:
nios2: kconfig: remove duplicate DEBUG_STACK_USAGE symbol defintions
|
|
If the display has been disabled by modparam, we still want to connect
together the HW bits and bobs with the associated drivers so that we can
continue to manage their runtime power gating.
Fixes: 108109444ff6 ("drm/i915: Check num_pipes before initializing audio component")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Elaine Wang <elaine.wang@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180817100241.4628-1-chris@chris-wilson.co.uk
(cherry picked from commit 35a5fd9ebfa93758ca579e30f337b6c9126d995b)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
100 ms is not enough time for the LSPCON adapter on Intel NUC devices to
settle. This causes dropped display modes at boot or screen reconfiguration.
Empirical testing can reproduce the error up to a timeout of 190 ms. Basic
boot and stress testing at 200 ms has not (yet) failed.
Increase timeout to 400 ms to get some margin of error.
Changes from v1:
The initial suggestion of 1000 ms was lowered due to concerns about delaying
valid timeout cases.
Update patch metadata.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107503
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1570392
Fixes: 357c0ae9198a ("drm/i915/lspcon: Wait for expected LSPCON mode to settle")
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: <stable@vger.kernel.org> # v4.11+
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Fredrik Schön <fredrik.schon@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180817200728.8154-1-fredrik.schon@gmail.com
(cherry picked from commit 59f1c8ab30d6f9042562949f42cbd3f3cf69de94)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
The context owns both the ppgtt and the vma within it, and our activity
tracking on the context ensures that we do not release active ppgtt. As
the context fulfils our obligations for active memory tracking, we can
relinquish the reference from the vma.
This fixes a silly transient refleak from closed vma being kept alive
until the entire system was idle, keeping all vm alive as well.
Reported-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Testcase: igt/gem_ctx_create/files
Fixes: 3365e2268b6b ("drm/i915: Lazily unbind vma on close")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Tested-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180816073448.19396-1-chris@chris-wilson.co.uk
(cherry picked from commit a4417b7b419a68540ad7945ac4efbb39d19afa63)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
- Check for the right CPU feature bit in sm4-ce on arm64.
- Fix scatterwalk WARN_ON in aes-gcm-ce on arm64.
- Fix unaligned fault in aesni on x86.
- Fix potential NULL pointer dereference on exit in chtls.
- Fix DMA mapping direction for RSA in caam.
- Fix error path return value for xts setkey in caam.
- Fix address endianness when DMA unmapping in caam.
- Fix sleep-in-atomic in vmx.
- Fix command corruption when queue is full in cavium/nitrox.
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: cavium/nitrox - fix for command corruption in queue full case with backlog submissions.
crypto: vmx - Fix sleep-in-atomic bugs
crypto: arm64/aes-gcm-ce - fix scatterwalk API violation
crypto: aesni - Use unaligned loads from gcm_context_data
crypto: chtls - fix null dereference chtls_free_uld()
crypto: arm64/sm4-ce - check for the right CPU feature bit
crypto: caam - fix DMA mapping direction for RSA forms 2 & 3
crypto: caam/qi - fix error path in xts setkey
crypto: caam/jr - fix descriptor DMA unmapping
|
|
Enable K3 SoC platform for TI's AM6 SoC.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This updates the ARM Versatile defconfig to the latest
Kconfig structural changes and adds the DUMB VGA bridge
driver so that VGA works out of the box, e.g. with QEMU.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
i.MX fixes for 4.19:
- i.MX display folks decided to switch MXS display driver from legacy
FB to DRM during 4.19 merge window. It leads to a fallout on some
Freescale/NXP development boards with Seiko 43WVF1G panel, because
this DRM panel driver is not enabled in i.MX defconfig. Here is
a series from Fabio to convert i.MX23/28 EVK DT to Seiko 43WVF1G
panel bindings and enable the panel driver in i.MX defconfig, so that
users can still get functional LCD on these boards by default.
- A fix from Leonard to revert incorrect legacy PCI irq mapping in
i.MX7 device tree, that was caused by document errors.
* tag 'imx-fixes-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx_v6_v7_defconfig: Select CONFIG_DRM_PANEL_SEIKO_43WVF1G
ARM: mxs_defconfig: Select CONFIG_DRM_PANEL_SEIKO_43WVF1G
ARM: dts: imx23-evk: Convert to the new display bindings
ARM: dts: imx23-evk: Move regulators outside simple-bus
ARM: dts: imx28-evk: Convert to the new display bindings
ARM: dts: imx28-evk: Move regulators outside simple-bus
Revert "ARM: dts: imx7d: Invert legacy PCI irq mapping"
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
RZ/G2M (R8A774A1) watchdog implementation is compatible with R-Car
Gen3, therefore add relevant documentation.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|
|
Daniel Borkmann says:
====================
This set contains three more fixes for the bpf_msg_pull_data()
mainly for correcting scatterlist ring wrap-arounds as well as
fixing up data pointers. For details please see individual patches.
Thanks!
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
When we perform the sg shift repair for the scatterlist ring, we
currently start out at i = first_sg + 1. However, this is not
correct since the first_sg could point to the sge sitting at slot
MAX_SKB_FRAGS - 1, and a subsequent i = MAX_SKB_FRAGS will access
the scatterlist ring (sg) out of bounds. Add the sk_msg_iter_var()
helper for iterating through the ring, and apply the same rule
for advancing to the next ring element as we do elsewhere. Later
work will use this helper also in other places.
Fixes: 015632bb30da ("bpf: sk_msg program helper bpf_sk_msg_pull_data")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
If first_sg and last_sg wraps around in the scatterlist ring, then we
need to account for that in the shift as well. E.g. crafting such msgs
where this is the case leads to a hang as shift becomes negative. E.g.
consider the following scenario:
first_sg := 14 |=> shift := -12 msg->sg_start := 10
last_sg := 3 | msg->sg_end := 5
round 1: i := 15, move_from := 3, sg[15] := sg[ 3]
round 2: i := 0, move_from := -12, sg[ 0] := sg[-12]
round 3: i := 1, move_from := -11, sg[ 1] := sg[-11]
round 4: i := 2, move_from := -10, sg[ 2] := sg[-10]
[...]
round 13: i := 11, move_from := -1, sg[ 2] := sg[ -1]
round 14: i := 12, move_from := 0, sg[ 2] := sg[ 0]
round 15: i := 13, move_from := 1, sg[ 2] := sg[ 1]
round 16: i := 14, move_from := 2, sg[ 2] := sg[ 2]
round 17: i := 15, move_from := 3, sg[ 2] := sg[ 3]
[...]
This means we will loop forever and never hit the msg->sg_end condition
to break out of the loop. When we see that the ring wraps around, then
the shift should be MAX_SKB_FRAGS - first_sg + last_sg - 1. Meaning,
the remainder slots from the tail of the ring and the head until last_sg
combined.
Fixes: 015632bb30da ("bpf: sk_msg program helper bpf_sk_msg_pull_data")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
In the current code, msg->data is set as sg_virt(&sg[i]) + start - offset
and msg->data_end relative to it as msg->data + bytes. Using iterator i
to point to the updated starting scatterlist element holds true for some
cases, however not for all where we'd end up pointing out of bounds. It
is /correct/ for these ones:
1) When first finding the starting scatterlist element (sge) where we
find that the page is already privately owned by the msg and where
the requested bytes and headroom fit into the sge's length.
However, it's /incorrect/ for the following ones:
2) After we made the requested area private and updated the newly allocated
page into first_sg slot of the scatterlist ring; when we find that no
shift repair of the ring is needed where we bail out updating msg->data
and msg->data_end. At that point i will point to last_sg, which in this
case is the next elem of first_sg in the ring. The sge at that point
might as well be invalid (e.g. i == msg->sg_end), which we use for
setting the range of sg_virt(&sg[i]). The correct one would have been
first_sg.
3) Similar as in 2) but when we find that a shift repair of the ring is
needed. In this case we fix up all sges and stop once we've reached the
end. In this case i will point to will point to the new msg->sg_end,
and the sge at that point will be invalid. Again here the requested
range sits in first_sg.
Fixes: 015632bb30da ("bpf: sk_msg program helper bpf_sk_msg_pull_data")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
This caused a confusing error message, but there is functionally
no problem since the default method is DIRECT.
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Move some KFD-related (but used in amdgpu_drv.c) definitions from
kfd_priv.h to kgd_kfd_interface.h so we don't need to include kfd_priv.h
in amdgpu_drv.c. This fixes a build failure when AMDGPU is enabled but
MMU_NOTIFIER is not.
This patch also disables KFD-related module options when HSA_AMD is not
enabled.
v2: rebase (Alex)
Signed-off-by: Amber Lin <Amber.Lin@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
kvmalloc_array uses __GFP_ZERO flag ensures that the returned address
is zeroed already, memset it to zero again afterwards is unnecessary,
and in this case buggy because we only clear the first entry.
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The first parameter of list_cut_position() must point to an initialized
list.
Noticed thanks to KASAN pointing out something's fishy here.
Fixes: "drm/ttm: add bulk move function on LRU"
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Instead of the larger one use the smaller hole in the MC address
space for the GART mappings.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This reverts commit 31625ccae4464b61ec8cdb9740df848bbc857a5b.
It triggered various badness on my development machine when running the
piglit gpu profile with radeonsi on Bonaire, looks like memory
corruption due to insufficiently protected list manipulations.
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Most of the time we only need to know if the BO has a valid GMC addr.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Further separate GART and GTT domain.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Improve the VCE limitation handling.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Move that into amdgpu_gmc.c since we are really deadling with GMC
address space here.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Not used any more.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
For compute vm acquired from amdgpu, vm.pasid is managed
by kfd. Decouple pasid from such vm on process destroy
to avoid duplicate pasid release.
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
To make a amdgpu vm to a compute vm, the old pasid will be freed and
replaced with a pasid managed by kfd. Kfd can't reuse original pasid
allocated by amdgpu because kfd uses different pasid policy with amdgpu.
For example, all graphic devices share one same pasid in a process.
v2: rebase (Alex)
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Pull NVMe fixes from Christoph.
* 'nvme-4.19' of git://git.infradead.org/nvme:
nvmet: free workqueue object if module init fails
nvme-fcloop: Fix dropped LS's to removed target port
nvme-pci: add a memory barrier to nvme_dbbuf_update_and_check_event
|
|
Like d88b6d04: "cdrom: information leak in cdrom_ioctl_media_changed()"
There is another cast from unsigned long to int which causes
a bounds check to fail with specially crafted input. The value is
then used as an index in the slot array in cdrom_slot_status().
Signed-off-by: Scott Bauer <scott.bauer@intel.com>
Signed-off-by: Scott Bauer <sbauer@plzdonthack.me>
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Add of_get_compatible_child() helper that can be used to lookup
compatible child nodes.
Several drivers currently use of_find_compatible_node() to lookup child
nodes while failing to notice that the of_find_ functions search the
entire tree depth-first (from a given start node) and therefore can
match unrelated nodes. The fact that these functions also drop a
reference to the node they start searching from (e.g. the parent node)
is typically also overlooked, something which can lead to use-after-free
bugs.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
On finishing the reset, the intention is to restart the GPU before we
relinquish the forcewake taken to handle the reset - the goal being the
GPU reloads a context before it is allowed to sleep. For this purpose,
we used tasklet_flush() which although it accomplished the goal of
restarting the GPU, carried with it a sting in its tail: it cleared the
TASKLET_STATE_SCHED bit. This meant that if another CPU queued a new
request to this engine, we would clear the flag and later attempt to
requeue the tasklet on the local CPU, breaking the per-cpu softirq
lists.
Remove the dangerous tasklet_kill() and just run the tasklet func
directly as we know it is safe to do so (the tasklets are internally
locked to allow mixed usage from direct submission).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180828152702.27536-1-chris@chris-wilson.co.uk
|
|
If dwapb_gpio_add_port() fails in dwapb_gpio_probe(),
gpio->clk is left undisabled.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
If we are being configured via pdata we don't necessarily have
any gpio mappings being configured that way so pdata->gpio_config
could be NULL.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
1. interrupt register define error lead to enable interrupt failed;
2. px30 unsupport hdmi output;
3. there are some hardware designed bug, we must swap win2 gate and
enable offset, otherwise will appear vop iommu pagefault.
Signed-off-by: Sandy Huang <hjc@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/1535445150-40296-1-git-send-email-hjc@rock-chips.com
|
|
Commit a203728ac6bb ("pinctrl: core: Return selector to the pinctrl
driver") and commit f913cfce4ee4 ("pinctrl: pinmux: Return selector to
the pinctrl driver") modified the return values of
pinctrl_generic_add_group() and pinmux_generic_add_function()
respectively, but did so without updating their callers. This broke the
pinctrl-ingenic driver, which treats non-zero return values from these
functions as errors & fails to probe. For example on a MIPS Ci20:
pinctrl-ingenic 10010000.pin-controller: Failed to register group uart0-hwflow
pinctrl-ingenic: probe of 10010000.pin-controller failed with error 1
Without the pinctrl driver probed, other drivers go on to fail to probe
too & the system is unusable.
Fix this by modifying the error checks to treat only negative values as
errors, matching the commits that introduced the breakage & similar
changes made to other drivers.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: a203728ac6bb ("pinctrl: core: Return selector to the pinctrl driver")
Fixes: f913cfce4ee4 ("pinctrl: pinmux: Return selector to the pinctrl driver")
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-gpio@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = devm_kzalloc(dev, sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
or, like in this particular case:
size = sizeof(struct foo) + sizeof(void *) * count;
instance = devm_kzalloc(dev, size, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = devm_kzalloc(dev, struct_size(instance, entry, count),
GFP_KERNEL);
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20180826184712.GA9330@embeddedor.com
|
|
GpioInt ACPI event handlers may see there IRQ triggered immediately
after requesting the IRQ (esp. level triggered ones). This means that they
may run before any other (builtin) drivers have had a chance to register
their OpRegion handlers, leading to errors like this:
[ 1.133274] ACPI Error: No handler for Region [PMOP] ((____ptrval____)) [UserDefinedRegion] (20180531/evregion-132)
[ 1.133286] ACPI Error: Region UserDefinedRegion (ID=141) has no handler (20180531/exfldio-265)
[ 1.133297] ACPI Error: Method parse/execution failed \_SB.GPO2._L01, AE_NOT_EXIST (20180531/psparse-516)
We already defer the manual initial trigger of edge triggered interrupts
by running it from a late_initcall handler, this commit replaces this with
deferring the entire acpi_gpiochip_request_interrupts() call till then,
fixing the problem of some OpRegions not being registered yet.
Note that this removes the need to have a list of edge triggered handlers
which need to run, since the entire acpi_gpiochip_request_interrupts() call
is now delayed, acpi_gpiochip_request_interrupt() can call these directly
now.
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The commit ca876c7483b6
("gpiolib-acpi: make sure we trigger edge events at least once on boot")
added a initial value check for pin which is about to be locked as IRQ.
Unfortunately, not all GPIO drivers can do that atomically. Thus,
switch to cansleep version of the call. Otherwise we have a warning:
...
WARNING: CPU: 2 PID: 1408 at drivers/gpio/gpiolib.c:2883 gpiod_get_value+0x46/0x50
...
RIP: 0010:gpiod_get_value+0x46/0x50
...
The change tested on Intel Broxton with Whiskey Cove PMIC GPIO controller.
Fixes: ca876c7483b6 ("gpiolib-acpi: make sure we trigger edge events at least once on boot")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Align with other drivers, tab + 2 space key for description.
and edp/hdmi/dsi can be used on both rk3288 and rk3399.
Signed-off-by: Sandy Huang <hjc@rock-chips.com>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/1535442295-4007-1-git-send-email-hjc@rock-chips.com
|
|
Using a private template is problematic:
1. We can't assign both a zone and a timeout policy
(zone assigns a conntrack template, so we hit problem 1)
2. Using a template needs to take care of ct refcount, else we'll
eventually free the private template due to ->use underflow.
This patch reworks template policy to instead work with existing conntrack.
As long as such conntrack has not yet been placed into the hash table
(unconfirmed) we can still add the timeout extension.
The only caveat is that we now need to update/correct ct->timeout to
reflect the initial/new state, otherwise the conntrack entry retains the
default 'new' timeout.
Side effect of this change is that setting the policy must
now occur from chains that are evaluated *after* the conntrack lookup
has taken place.
No released kernel contains the timeout policy feature yet, so this change
should be ok.
Changes since v2:
- don't handle 'ct is confirmed case'
- after previous patch, no need to special-case tcp/dccp/sctp timeout
anymore
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
tcp, sctp and dccp trackers re-use the userspace ctnetlink states
to index their timeout arrays, which means timeout[0] is never
used. Copy the 'new' state (syn-sent, dccp-request, ..) to 0 as well
so external users can simply read it off timeouts[0] without need to
differentiate dccp/sctp/tcp and udp/icmp/gre/generic.
The alternative is to map all array accesses to 'i - 1', but that
is a much more intrusive change.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
