| Age | Commit message (Collapse) | Author |
|---|
|
Conditional add/remove quirks for MMC and SD.
Signed-off-by: Andrei Warkentin <andreiw@motorola.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Add a driver for Elan Digital System's VUB300 chip which is a USB
connected SDIO/SDmem/MMC host controller. A VUB300 chip enables a USB 2.0
or USB 1.1 connected host computer to use SDIO/SD/MMC cards without the
need for a directly connected, for example via PCI, SDIO host controller.
Signed-off-by: Anthony F Olech <tony.olech@elandigitalsystems.com>
[cjb: various punctuation and style fixes]
Tested-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
32 Bit DMA/ADMA Access
32 Bit Size
Support ADMA End Descriptor in current chain
(no need for dummy entry)
Signed-off-by: Philip Rakity <prakity@marvell.com>
Tested-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
mmc_rescan_try_freq() tries to init two times with the last frequency.
For example, if host->f_min is 400KHz, we see the message below:
mmc1: mmc_rescan_try_freq: trying to init card at 400000 Hz
mmc1: mmc_rescan_try_freq: trying to init card at 400000 Hz
Andy Ross says that he didn't try this code on a board with an f_min
that exactly matches one of the table entries, which explains why the
bug wasn't detected.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Andy Ross <andy.ross@windriver.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
eMMC voltage change not required for 1.8V. 3.3V and 1.8V vcc
are capable of doing DDR. vccq of 1.8v is not required.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Reviewed-by: Arindam Nath <arindam.nath@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
eMMC chips do not use CMD11 when changing voltage. Add extra
argument to call to indicate if CMD11 needs to be sent.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Reviewed-by: Arindam Nath <arindam.nath@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Marvell controller requires 1.8V bit in UHS control register 2
be set when doing UHS. eMMC does not require 1.8V for DDR.
add platform code to handle this.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Reviewed-by: Arindam Nath <arindam.nath@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Allow platform specific code to set UHS registers if
implementation requires speciial platform specific handling
Signed-off-by: Philip Rakity <prakity@marvell.com>
Reviewed-by: Arindam Nath <arindam.nath@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Since the MMC_PM_KEEP_POWER flag should be set on each suspend,
it should also cleared on each resume.
Upon resuming, we have to know if power was kept
(for re-initialization, etc.), so clear it just after resuming.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
regulator_enable() was incorrectly placed in the suspend function
instead of the resume function.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Supply a link to TMIO private data for platforms to implement their
own card detection.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The TMIO MMC controller cannot be powered off to save power, when no
card is plugged in, because then it will not be able to detect a new
card-insertion event. On some implementations, however, it is
possible to switch to using another source to detect card insertion.
This patch adds support for such implementations.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Convert the SDHI code to support more than a single interrupt source.
Needed to support hardware that uses GIC instead of INTC as interrupt
controller.
Will also allow us to remove the irq forwarding workaround from the
INTC code in the future.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Instead of printing out useless information such as the virtual base
address and one of 4 interrupts, convert the SDHI probe() to print
out physical base address together with clock rate.
We do have a struct device so make use of dev_info().
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Modify the SDHI driver to get rid of unwanted irq flags.
IRQF_DISABLED unused, see include/linux/interrupt.h
IRQF_TRIGGER_FALLING only relevant on external IRQ pins,
but since SDHI is internal in the SoC this can go away.
Needed to support SDHI on sh73a0 that comes with a GIC
that errors out with the IRQF_TRIGGER_FALLING setting.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Move request_irq()/free_irq() from the shared code
in tmio_mmc.c into the SDHI/tmio specific portion
in sh_mobile_sdhi.c and tmio_mmc_pio.c.
This is ground work to allow us to adjust the SDHI
code with IRQ flags and number of interupt sources.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The MMC subsystem does not guarantee, that host driver .request() and
.set_ios() callbacks are serialised. Such concurrent calls, however,
do not have to be meaningfully supported, drivers just have to make
sure to avoid any severe problems.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Adding support for runtime power-management to the MMCIF driver allows
it to save power as long as no card is present. To also allow to turn
off the power domain at that time, we release DMA channels during that
time, since on some sh-mobile systems the DMA controller(s) and the
MMCIF block belong to the same power domain. System-wide power
management has been tested with experimental PM patches on AP4-based
systems.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Add runtime and system-wide power management to the TMIO MMC driver
in PIO and DMA modes, allowing it to properly save and restore its
state during system suspend. Runtime PM is very crude ATM, because
the controller has to be powered on all the time to detect card
hotplug events.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The MMC subsystem does not guarantee that host driver .request() and
.set_ios() callbacks are serialised. Such concurrent calls, however,
do not have to be meaningfully supported, drivers just have to make
sure to avoid any severe problems.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Simon Horman <horms@verge.net.au>
Cc: Magnus Damm <damm@opensource.se>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
If there is only 1 function interrupt registered it is possible to
improve performance by directly calling the irq handler and avoiding
the overhead of reading the CCCR registers.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@stericsson.com>
Reviewed-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
When allocation of idata failed there was a null dereference. Also avoid
calling kfree where it isn't needed.
Signed-off-by: Vladimir Motyka <vladimir.motyka@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Host Controller v3.00 can support retuning modes 1,2 or 3 depending on
the bits 46-47 of the Capabilities register. Also, the timer count for
retuning is indicated by bits 40-43 of the same register. We initialize
timer_list for retuning the first time we execute tuning procedure. This
condition is indicated by SDHCI_NEEDS_RETUNING not being set. Since
retuning mode 1 sets a limit of 4MB on the maximum data length, we set
max_blk_count appropriately. Once the tuning timer expires, we set
SDHCI_NEEDS_RETUNING flag, and if the flag is set, we execute tuning
procedure before sending the next command. We need to restore mmc_request
structure after executing retuning procedure since host->mrq is used
inside the procedure to send CMD19. We also disable and re-enable this
flag during suspend and resume respectively, as per the spec v3.00.
Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Host Controller v3.00 supports programmable clock mode as an optional
feature. The support for this mode is indicated by non-zero value in
bits 48-55 of the Capabilities register. If supported, the actual
value of Clock Multiplier is one more than the value provided in the
bit fields. We only set Clock Generator Select (bit 5) and SDCLK
Frequency Select (bits 8-15) of the Clock Control register in case
Preset Value Enable is not set, otherwise these fields are automatically
set by the Host Controller based on the UHS mode selected. Also, since
the maximum and minimum clock frequency in this mode can be
(Base Clock * Clock Mul) and (Base Clock * Clock Mul)/1024 respectively,
f_max and f_min have been recalculated to reflect this change.
Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
According to the Host Controller spec v3.00, setting Preset Value Enable
in the Host Control2 register lets SDCLK Frequency Select, Clock Generator
Select and Driver Strength Select to be set automatically by the Host
Controller based on the UHS-I mode set. This patch enables this feature.
Since Preset Value Enable makes sense only for UHS-I cards, we enable this
feature after successfull UHS-I initialization. We also reset Preset Value
Enable next time before initialization.
Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Host Controller needs tuning during initialization to operate SDR50
and SDR104 UHS-I cards. Whether SDR50 mode actually needs tuning is
indicated by bit 45 of the Host Controller Capabilities register.
A new command CMD19 has been defined in the Physical Layer spec
v3.01 to request the card to send tuning pattern.
We enable Buffer Read Ready interrupt at the very begining of tuning
procedure, because that is the only interrupt generated by the Host
Controller during tuning. We program the block size to 64 in the
Block Size register. We make sure that DMA Enable and Multi Block
Select in the Transfer Mode register are set to 0 before actually
sending CMD19. The tuning block is sent by the card to the Host
Controller using DAT lines, so we set Data Present Select (bit 5) in
the Command register. The Host Controller is responsible for doing
the verfication of tuning block sent by the card at the hardware
level. After sending CMD19, we wait for Buffer Read Ready interrupt.
In case we don't receive an interrupt after the specified timeout
value, we fall back on fixed sampling clock by setting Execute
Tuning (bit 6) and Sampling Clock Select (bit 7) of Host Control2
register to 0. Before exiting the tuning procedure, we disable Buffer
Read Ready interrupt and re-enable other interrupts.
Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Since only UHS-I cards respond with S18A set in response to ACMD41,
we set the card as ultra-high-speed after successfull initialization.
We need to decide whether a card is SDXC based on the C_SIZE field
of CSDv2.0 register. According to Physical Layer spec v3.01, the
minimum value of C_SIZE for SDXC card is 00FFFFh.
Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
We decide on the current limit to be set for the card based on the
Capability of Host Controller to provide current at 1.8V signalling,
and the maximum current limit of the card as indicated by CMD6
mode 0. We then set the current limit for the card using CMD6 mode 1.
As per the Physical Layer Spec v3.01, the current limit switch is
only applicable for SDR50, SDR104, and DDR50 bus speed modes. For
other UHS-I modes, we set the default current limit of 200mA.
Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
This patch adds support for setting UHS-I bus speed mode during UHS-I
initialization procedure. Since both the host and card can support
more than one bus speed, we select the highest speed based on both of
their capabilities. First we set the bus speed mode for the card using
CMD6 mode 1, and then we program the host controller to support the
required speed mode. We also set High Speed Enable in case one of the
UHS-I modes is selected. We take care to reset SD clock before setting
UHS mode in the Host Control2 register, and then re-enable it as per
the Host Controller spec v3.00. We then set the clock frequency for
the UHS-I mode selected.
Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
As per Host Controller spec v3.00, we reset SDCLK before setting
High Speed Enable, and then set it back to avoid generating clock
gliches. Before enabling SDCLK again, we make sure the clock is
stable, so we use sdhci_set_clock().
Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
This patch adds support for setting driver strength during UHS-I
initialization procedure. Since UHS-I cards set S18A (bit 24) in
response to ACMD41, we use this as a base for UHS-I initialization.
We modify the parameter list of mmc_sd_get_cid() so that we can
save the ROCR from ACMD41 to check whether bit 24 is set.
We decide whether the Host Controller supports A, C, or D driver
type depending on the Capabilities register. Driver type B is
suported by default. We then set the appropriate driver type for
the card using CMD6 mode 1. As per Host Controller spec v3.00, we
set driver type for the host only if Preset Value Enable in the
Host Control2 register is not set. SDHCI_HOST_CONTROL has been
renamed to SDHCI_HOST_CONTROL1 to conform to the spec.
Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
renesas_usbhs is remake version of r8a66597
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
If the MERAM platform data is defined, but the MERAM has not been
properly initaliazed we need to safely fall back to non-MERAM operation.
Signed-off-by: Damian Hobson-Garcia <dhobsong@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This makes it possible to leave DMA slave IDs in the platform data
at default 0 value without hitting DMA channel allocation error paths.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This makes it possible to leave DMA slave IDs in the platform data
at default 0 value without hitting DMA channel allocation error paths.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Add SDHI0 and SDHI1 slave ids for RX and TX to enable
DMA Engine support for SDHI on the AG5EVM board.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Simply add MMCIF slave ids for RX and TX to enable
DMA Engine support for the AG5EVM board.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Add SY-DMAC support via shdma.c to the sh73a0 SoC
including slave ids, platform data and clock bindings.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Update SH_DMAC_MAX_CHANNELS to support the 20 DMA
channels included in the sh73a0 SY-DMAC hardware.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Fix the shdma.c handing of SH_DMAC_MAX_CHANNELS
to avoid overwriting the chan_irq[] and chan_flag[]
arrays in the case of pdata->channel_num is larger
than SH_DMAC_MAX_CHANNELS.
With this patch applied up to SH_DMAC_MAX_CHANNELS
will be used by the shdma.c driver. If more channels
are available in the platform data the user will
be notified on the console.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This patch makes the shdma.c driver allow slave operation
on DMA hardware mapped with a single I/O-memory window.
The dmae_set_dmars() function is adjusted to use the
first memory window in case of a missing DMARS window.
At probe() time the code is updated to enable DMA_SLAVE
only if slave information is passed with the platform data.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This patch ties in the previously added sh7372 sleep
mode known as Core Standby together with the shared
SH-Mobile ARM CPUIdle implementation.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This patch adds a shared SH-Mobile ARM specific CPUIdle
implementation supporting WFI only at this point. It
serves as a common point for late registration of the
arch-specific CPUIdle code, and supports adding extra
sleep modes using the callback shmobile_cpuidle_setup()
together with shmobile_cpuidle_modes[].
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Add sh7372 Core Standby sleep mode support and tie it
in with the shared SH-Mobile ARM suspend code.
The Core Standby mode is the lightest sh7372-specific
sleep mode, cutting power to the ARM core excluding the
L2 cache. Any interrupt source can be used for wakeups.
The low level portion of this code is based on the
TI OMAP sleep code in sleep34xx.S, thanks to them.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This patch adds a simple Suspend-to-RAM implementation
for SH-Mobile ARM. The struct shmobile_suspend_ops are
kept global to allow cpu-specific code to override
the callbacks if needed.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
|
|
SD cards which conform to Physical Layer Spec v3.01 can support
additional Bus Speed Modes, Driver Strength, and Current Limit
other than the default values. We use CMD6 mode 0 to read these
additional card functions. The values read here will be used
during UHS-I initialization steps.
Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Host Controller v3.00 adds another Capabilities register. Apart
from other things, this new register indicates whether the Host
Controller supports SDR50, SDR104, and DDR50 UHS-I modes. The spec
doesn't mention about explicit support for SDR12 and SDR25 UHS-I
modes, so the Host Controller v3.00 should support them by default.
Also if the controller supports SDR104 mode, it will also support
SDR50 mode as well. So depending on the host support, we set the
corresponding MMC_CAP_* flags. One more new register. Host Control2
is added in v3.00, which is used during Signal Voltage Switch
procedure described below.
Since as per v3.00 spec, UHS-I supported hosts should set S18R
to 1, we set S18R (bit 24) of OCR before sending ACMD41. We also
need to set XPC (bit 28) of OCR in case the host can supply >150mA.
This support is indicated by the Maximum Current Capabilities
register of the Host Controller.
If the response of ACMD41 has both CCS and S18A set, we start the
signal voltage switch procedure, which if successfull, will switch
the card from 3.3V signalling to 1.8V signalling. Signal voltage
switch procedure adds support for a new command CMD11 in the
Physical Layer Spec v3.01. As part of this procedure, we need to
set 1.8V Signalling Enable (bit 3) of Host Control2 register, which
if remains set after 5ms, means the switch to 1.8V signalling is
successfull. Otherwise, we clear bit 24 of OCR and retry the
initialization sequence. When we remove the card, and insert the
same or another card, we need to make sure that we start with 3.3V
signalling voltage. So we call mmc_set_signal_voltage() with
MMC_SIGNAL_VOLTAGE_330 set so that we are back to 3.3V signalling
voltage before we actually start initializing the card.
Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
