| Age | Commit message (Collapse) | Author |
|---|
|
Extend x86's set sregs test to verify that KVM sets/clears OSXSAVE and
OSKPKE according to CR4.XSAVE and CR4.PKE respectively. For performance
reasons, KVM is responsible for emulating the architectural behavior of
the OS CPUID bits tracking CR4.
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Binbin Wu <binbin.wu@linux.intel.com>
Reviewed-by: Xiaoyao Li <xiaoyao.li@intel.com>
Link: https://lore.kernel.org/r/20241128013424.4096668-10-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
Refresh selftests' CPUID cache in the vCPU structure when querying a CPUID
entry so that tests don't consume stale data when KVM modifies CPUID as a
side effect to a completely unrelated change. E.g. KVM adjusts OSXSAVE in
response to CR4.OSXSAVE changes.
Unnecessarily invoking KVM_GET_CPUID is suboptimal, but vcpu->cpuid exists
to simplify selftests development, not for performance reasons. And,
unfortunately, trying to handle the side effects in tests or other flows
is unpleasant, e.g. selftests could manually refresh if KVM_SET_SREGS is
successful, but that would still leave a gap with respect to guest CR4
changes.
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Link: https://lore.kernel.org/r/20241128013424.4096668-9-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
Add a sanity check in __vcpu_get_cpuid_entry() to provide a friendlier
error than a segfault when a test developer tries to use a vCPU CPUID
helper on a barebones vCPU.
Link: https://lore.kernel.org/r/20241128013424.4096668-8-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
Rework x86's set sregs test to verify that KVM enforces CPUID vs. CR4
features even if userspace hasn't explicitly set guest CPUID. KVM used to
allow userspace to set any KVM-supported CR4 value prior to KVM_SET_CPUID2,
and the test verified that behavior.
However, the testcase was written purely to verify KVM's existing behavior,
i.e. was NOT written to match the needs of real world VMMs.
Opportunistically verify that KVM continues to reject unsupported features
after KVM_SET_CPUID2 (using KVM_GET_SUPPORTED_CPUID).
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Binbin Wu <binbin.wu@linux.intel.com>
Reviewed-by: Xiaoyao Li <xiaoyao.li@intel.com>
Link: https://lore.kernel.org/r/20241128013424.4096668-7-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
Drop x86.c's local pre-computed cr4_reserved bits and instead fold KVM's
reserved bits into the guest's reserved bits. This fixes a bug where VMX's
set_cr4_guest_host_mask() fails to account for KVM-reserved bits when
deciding which bits can be passed through to the guest. In most cases,
letting the guest directly write reserved CR4 bits is ok, i.e. attempting
to set the bit(s) will still #GP, but not if a feature is available in
hardware but explicitly disabled by the host, e.g. if FSGSBASE support is
disabled via "nofsgsbase".
Note, the extra overhead of computing host reserved bits every time
userspace sets guest CPUID is negligible. The feature bits that are
queried are packed nicely into a handful of words, and so checking and
setting each reserved bit costs in the neighborhood of ~5 cycles, i.e. the
total cost will be in the noise even if the number of checked CR4 bits
doubles over the next few years. In other words, x86 will run out of CR4
bits long before the overhead becomes problematic.
Note #2, __cr4_reserved_bits() starts from CR4_RESERVED_BITS, which is
why the existing __kvm_cpu_cap_has() processing doesn't explicitly OR in
CR4_RESERVED_BITS (and why the new code doesn't do so either).
Fixes: 2ed41aa631fc ("KVM: VMX: Intercept guest reserved CR4 bits to inject #GP fault")
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Chao Gao <chao.gao@intel.com>
Reviewed-by: Binbin Wu <binbin.wu@linux.intel.com>
Reviewed-by: Xiaoyao Li <xiaoyao.li@intel.com>
Link: https://lore.kernel.org/r/20241128013424.4096668-6-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
Explicitly perform runtime CPUID adjustments as part of the "after set
CPUID" flow to guard against bugs where KVM consumes stale vCPU/CPUID
state during kvm_update_cpuid_runtime(). E.g. see commit 4736d85f0d18
("KVM: x86: Use actual kvm_cpuid.base for clearing KVM_FEATURE_PV_UNHALT").
Whacking each mole individually is not sustainable or robust, e.g. while
the aforemention commit fixed KVM's PV features, the same issue lurks for
Xen and Hyper-V features, Xen and Hyper-V simply don't have any runtime
features (though spoiler alert, neither should KVM).
Updating runtime features in the "full" path will also simplify adding a
snapshot of the guest's capabilities, i.e. of caching the intersection of
guest CPUID and kvm_cpu_caps (modulo a few edge cases).
Link: https://lore.kernel.org/r/20241128013424.4096668-5-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
During vCPU creation, process KVM's default, empty CPUID as if userspace
set an empty CPUID to ensure consistent and correct behavior with respect
to guest CPUID. E.g. if userspace never sets guest CPUID, KVM will never
configure cr4_guest_rsvd_bits, and thus create divergent, incorrect, guest-
visible behavior due to letting the guest set any KVM-supported CR4 bits
despite the features not being allowed per guest CPUID.
Note! This changes KVM's ABI, as lack of full CPUID processing allowed
userspace to stuff garbage vCPU state, e.g. userspace could set CR4 to a
guest-unsupported value via KVM_SET_SREGS. But it's extremely unlikely
that this is a breaking change, as KVM already has many flows that require
userspace to set guest CPUID before loading vCPU state. E.g. multiple MSR
flows consult guest CPUID on host writes, and KVM_SET_SREGS itself already
relies on guest CPUID being up-to-date, as KVM's validity check on CR3
consumes CPUID.0x7.1 (for LAM) and CPUID.0x80000008 (for MAXPHYADDR).
Furthermore, the plan is to commit to enforcing guest CPUID for userspace
writes to MSRs, at which point bypassing sregs CPUID checks is even more
nonsensical.
Link: https://lore.kernel.org/r/20241128013424.4096668-4-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
Define and undefine the F() and SF() macros precisely around
kvm_set_cpu_caps() to make it all but impossible to use the macros outside
of kvm_cpu_cap_{mask,init_kvm_defined}(). Currently, F() is a simple
passthrough, but SF() is actively dangerous as it checks that the scattered
feature is supported by the host kernel.
And usage outside of the aforementioned helpers will run afoul of future
changes to harden KVM's CPUID management.
Opportunistically switch to feature_bit() when stuffing LA57 based on raw
hardware support.
No functional change intended.
Link: https://lore.kernel.org/r/20241128013424.4096668-3-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
When clearing CONSTANT_TSC during CPUID emulation due to a Hyper-V quirk,
use feature_bit() instead of SF() to ensure the bit is actually cleared.
SF() evaluates to zero if the _host_ doesn't support the feature. I.e.
KVM could keep the bit set if userspace advertised CONSTANT_TSC despite
it not being supported in hardware.
Note, translating from a scattered feature to a the hardware version is
done by __feature_translate(), not SF(). The sole purpose of SF() is to
check kernel support for the scattered feature, *before* translation.
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Link: https://lore.kernel.org/r/20241128013424.4096668-2-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
- tree-checker catches invalid number of inline extent references
- zoned mode fixes:
- enhance zone append IO command so it also detects emulated writes
- handle bio splitting at sectorsize boundary
- when deleting a snapshot, fix a condition for visiting nodes in reloc
trees
* tag 'for-6.13-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: tree-checker: reject inline extent items with 0 ref count
btrfs: split bios to the fs sector size boundary
btrfs: use bio_is_zone_append() in the completion handler
btrfs: fix improper generation check in snapshot delete
|
|
Now that KVM selftests uses the kernel's canonical arch paths, directly
override ARCH to 'x86' when targeting x86_64 instead of defining ARCH_DIR
to redirect to appropriate paths. ARCH_DIR was originally added to deal
with KVM selftests using the target triple ARCH for directories, e.g.
s390x and aarch64; keeping it around just to deal with the one-off alias
from x86_64=>x86 is unnecessary and confusing.
Note, even when selftests are built from the top-level Makefile, ARCH is
scoped to KVM's makefiles, i.e. overriding ARCH won't trip up some other
selftests that (somehow) expects x86_64 and can't work with x86.
Reviewed-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Link: https://lore.kernel.org/r/20241128005547.4077116-17-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
Use the kernel's canonical $(ARCH) paths instead of the raw target triple
for KVM selftests directories. KVM selftests are quite nearly the only
place in the entire kernel that using the target triple for directories,
tools/testing/selftests/drivers/s390x being the lone holdout.
Using the kernel's preferred nomenclature eliminates the minor, but
annoying, friction of having to translate to KVM's selftests directories,
e.g. for pattern matching, opening files, running selftests, etc.
Opportunsitically delete file comments that reference the full path of the
file, as they are obviously prone to becoming stale, and serve no known
purpose.
Reviewed-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Acked-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Acked-by: Andrew Jones <ajones@ventanamicro.com>
Link: https://lore.kernel.org/r/20241128005547.4077116-16-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
Provide empty targets for KVM selftests if the target architecture is
unsupported to make it obvious which architectures are supported, and so
that various side effects don't fail and/or do weird things, e.g. as is,
"mkdir -p $(sort $(dir $(TEST_GEN_PROGS)))" fails due to a missing operand,
and conversely, "$(shell mkdir -p $(sort $(OUTPUT)/$(ARCH_DIR) ..." will
create an empty, useless directory for the unsupported architecture.
Move the guts of the Makefile to Makefile.kvm so that it's easier to see
that the if-statement effectively guards all of KVM selftests.
Reported-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Acked-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Acked-by: Andrew Jones <ajones@ventanamicro.com>
Link: https://lore.kernel.org/r/20241128005547.4077116-15-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
Add two phases to mmu_stress_test to verify that KVM correctly handles
guest memory that was writable, and then made read-only in the primary MMU,
and then made writable again.
Add bonus coverage for x86 and arm64 to verify that all of guest memory was
marked read-only. Making forward progress (without making memory writable)
requires arch specific code to skip over the faulting instruction, but the
test can at least verify each vCPU's starting page was made read-only for
other architectures.
Link: https://lore.kernel.org/r/20241128005547.4077116-14-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
Add a third phase of mmu_stress_test to verify that mprotect()ing guest
memory to make it read-only doesn't cause explosions, e.g. to verify KVM
correctly handles the resulting mmu_notifier invalidations.
Reviewed-by: James Houghton <jthoughton@google.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Link: https://lore.kernel.org/r/20241128005547.4077116-13-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
Run the exact number of guest loops required in mmu_stress_test instead
of looping indefinitely in anticipation of adding more stages that run
different code (e.g. reads instead of writes).
Reviewed-by: James Houghton <jthoughton@google.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Link: https://lore.kernel.org/r/20241128005547.4077116-12-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
Use vcpu_arch_put_guest() to write memory from the guest in
mmu_stress_test as an easy way to provide a bit of extra coverage.
Reviewed-by: James Houghton <jthoughton@google.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Link: https://lore.kernel.org/r/20241128005547.4077116-11-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
Enable the mmu_stress_test on arm64. The intent was to enable the test
across all architectures when it was first added, but a few goofs made it
unrunnable on !x86. Now that those goofs are fixed, at least for arm64,
enable the test.
Cc: Oliver Upton <oliver.upton@linux.dev>
Cc: Marc Zyngier <maz@kernel.org>
Reviewed-by: James Houghton <jthoughton@google.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Link: https://lore.kernel.org/r/20241128005547.4077116-10-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
Explicitly include ucall_common.h in the MMU stress test, as unlike arm64
and x86-64, RISC-V doesn't include ucall_common.h in its processor.h, i.e.
this will allow enabling the test on RISC-V.
Reported-by: Andrew Jones <ajones@ventanamicro.com>
Link: https://lore.kernel.org/r/20241128005547.4077116-9-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
Create mmu_stress_tests's VM with the correct number of extra pages needed
to map all of memory in the guest. The bug hasn't been noticed before as
the test currently runs only on x86, which maps guest memory with 1GiB
pages, i.e. doesn't need much memory in the guest for page tables.
Reviewed-by: James Houghton <jthoughton@google.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Link: https://lore.kernel.org/r/20241128005547.4077116-8-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
Try to get/set SREGS in mmu_stress_test only when running on x86, as the
ioctls are supported only by x86 and PPC, and the latter doesn't yet
support KVM selftests.
Reviewed-by: James Houghton <jthoughton@google.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Link: https://lore.kernel.org/r/20241128005547.4077116-7-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
Rename max_guest_memory_test to mmu_stress_test so that the name isn't
horribly misleading when future changes extend the test to verify things
like mprotect() interactions, and because the test is useful even when its
configured to populate far less than the maximum amount of guest memory.
Reviewed-by: James Houghton <jthoughton@google.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Link: https://lore.kernel.org/r/20241128005547.4077116-6-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
Don't check for an unhandled exception if KVM_RUN failed, e.g. if it
returned errno=EFAULT, as reporting unhandled exceptions is done via a
ucall, i.e. requires KVM_RUN to exit cleanly. Theoretically, checking
for a ucall on a failed KVM_RUN could get a false positive, e.g. if there
were stale data in vcpu->run from a previous exit.
Reviewed-by: James Houghton <jthoughton@google.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Link: https://lore.kernel.org/r/20241128005547.4077116-5-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
Assert that the register being read/written by vcpu_{g,s}et_reg() is no
larger than a uint64_t, i.e. that a selftest isn't unintentionally
truncating the value being read/written.
Ideally, the assert would be done at compile-time, but that would limit
the checks to hardcoded accesses and/or require fancier compile-time
assertion infrastructure to filter out dynamic usage.
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Link: https://lore.kernel.org/r/20241128005547.4077116-4-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
Return a uint64_t from vcpu_get_reg() instead of having the caller provide
a pointer to storage, as none of the vcpu_get_reg() usage in KVM selftests
accesses a register larger than 64 bits, and vcpu_set_reg() only accepts a
64-bit value. If a use case comes along that needs to get a register that
is larger than 64 bits, then a utility can be added to assert success and
take a void pointer, but until then, forcing an out param yields ugly code
and prevents feeding the output of vcpu_get_reg() into vcpu_set_reg().
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Acked-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Link: https://lore.kernel.org/r/20241128005547.4077116-3-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
An important distinction from other registers affected by HPMN is that
PMCR_EL0 only affects the guest range of counters, regardless of the EL
from which it is accessed. Ensure that PMCR_EL0.P is always applied to
'guest' counters by manually computing the mask rather than deriving it
from the current context.
Reviewed-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20241217175611.3658290-1-oliver.upton@linux.dev
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
|
|
MDCR_EL2.HPME is the 'global' enable bit for event counters reserved for
EL2. Give the PMU a kick when it's changed to ensure events are
reprogrammed before returning to the guest.
Reviewed-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20241217175550.3658212-1-oliver.upton@linux.dev
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
|
|
Nested virt introduces yet another set of 'global' knobs for controlling
event counters that are reserved for EL2 (i.e. >= HPMN). Get ready to
share some plumbing with the NV controls by offloading counter
reprogramming to KVM_REQ_RELOAD_PMU.
Reviewed-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20241217175532.3658134-1-oliver.upton@linux.dev
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
|
|
Having separate helpers for enabling/disabling counters provides the
wrong abstraction, as the state of each counter needs to be evaluated
independently and, in some cases, use a different global enable bit.
Collapse the enable/disable accessors into a single, common helper that
reconfigures every counter set in @mask, leaving the complexity of
determining if an event is actually enabled in
kvm_pmu_counter_is_enabled().
Reviewed-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20241217175513.3658056-1-oliver.upton@linux.dev
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
|
|
There are multiple pKVM memory transitions where the state of a page is
not cross-checked from the completer's PoV for performance reasons.
For example, if a page is PKVM_PAGE_OWNED from the initiator's PoV,
we should be guaranteed by construction that it is PKVM_NOPAGE for
everybody else, hence allowing us to save a page-table lookup.
When it was introduced, hyp_ack_unshare() followed that logic and bailed
out without checking the PKVM_PAGE_SHARED_BORROWED state in the
hypervisor's stage-1. This was correct as we could safely assume that
all host-initiated shares were directed at the hypervisor at the time.
But with the introduction of other types of shares (e.g. for FF-A or
non-protected guests), it is now very much required to cross check this
state to prevent the host from running __pkvm_host_unshare_hyp() on a
page shared with TZ or a non-protected guest.
Thankfully, if an attacker were to try this, the hyp_unmap() call from
hyp_complete_unshare() would fail, hence causing to WARN() from
__do_unshare() with the host lock held, which is fatal. But this is
fragile at best, and can hardly be considered a security measure.
Let's just do the right thing and always check the state from
hyp_ack_unshare().
Signed-off-by: Quentin Perret <qperret@google.com>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20241128154406.602875-1-qperret@google.com
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl
Pull cxl fixes from Ira Weiny:
- prevent probe failure when non-critical RAS unmasking fails
- fix CXL 1.1 link status sysfs attribute
- fix 4 way (and greater) switch interleave region creation
* tag 'cxl-fixes-6.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl:
cxl/region: Fix region creation for greater than x2 switches
cxl/pci: Check dport->regs.rcd_pcie_cap availability before accessing
cxl/pci: Fix potential bogus return value upon successful probing
|
|
Use the helper function rather than reading it directly.
Reviewed-by: Yang Wang <kevinyang.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 0ec43fbece784215d3c4469973e4556d70bce915)
Cc: stable@vger.kernel.org
|
|
This helps to avoid a spurious PME event on hotplug to Azalia.
Cc: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Reported-and-tested-by: ionut_n2001@yahoo.com
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=215884
Tested-by: Gabriel Marcano <gabemarcano@yahoo.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://lore.kernel.org/r/20241211024414.7840-1-mario.limonciello@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 3f6f237b9dd189e1fb85b8a3f7c97a8f27c1e49a)
Cc: stable@vger.kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux
Pull selinux fix from Paul Moore:
"One small SELinux patch to get rid improve our handling of unknown
extended permissions by safely ignoring them.
Not only does this make it easier to support newer SELinux policy
on older kernels in the future, it removes to BUG() calls from the
SELinux code."
* tag 'selinux-pr-20241217' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux:
selinux: ignore unknown extended permissions
|
|
Commit a6021aa24f6417416d933 ("ACPI: EC: make EC support compile-time
conditional") only enable ACPI_EC on X86 by default, but the embedded
controller is also widely used on LoongArch laptops so we also enable
ACPI_EC for LoongArch.
The laptop driver cannot work without EC, so also update the dependency
of LOONGSON_LAPTOP to let it depend on APCI_EC.
Fixes: a6021aa24f6417416d933 ("ACPI: EC: make EC support compile-time conditional")
Reported-by: Xiaotian Wu <wuxiaotian@loongson.cn>
Tested-by: Binbin Zhou <zhoubinbin@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Link: https://patch.msgid.link/20241217073704.3339587-1-chenhuacai@loongson.cn
[ rjw: Added Fixes: ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The TP_printk() of a TRACE_EVENT() is a generic printf format that any
developer can create for their event. It may include pointers to strings
and such. A boot mapped buffer may contain data from a previous kernel
where the strings addresses are different.
One solution is to copy the event content and update the pointers by the
recorded delta, but a simpler solution (for now) is to just use the
print_fields() function to print these events. The print_fields() function
just iterates the fields and prints them according to what type they are,
and ignores the TP_printk() format from the event itself.
To understand the difference, when printing via TP_printk() the output
looks like this:
4582.696626: kmem_cache_alloc: call_site=getname_flags+0x47/0x1f0 ptr=00000000e70e10e0 bytes_req=4096 bytes_alloc=4096 gfp_flags=GFP_KERNEL node=-1 accounted=false
4582.696629: kmem_cache_alloc: call_site=alloc_empty_file+0x6b/0x110 ptr=0000000095808002 bytes_req=360 bytes_alloc=384 gfp_flags=GFP_KERNEL node=-1 accounted=false
4582.696630: kmem_cache_alloc: call_site=security_file_alloc+0x24/0x100 ptr=00000000576339c3 bytes_req=16 bytes_alloc=16 gfp_flags=GFP_KERNEL|__GFP_ZERO node=-1 accounted=false
4582.696653: kmem_cache_free: call_site=do_sys_openat2+0xa7/0xd0 ptr=00000000e70e10e0 name=names_cache
But when printing via print_fields() (echo 1 > /sys/kernel/tracing/options/fields)
the same event output looks like this:
4582.696626: kmem_cache_alloc: call_site=0xffffffff92d10d97 (-1831793257) ptr=0xffff9e0e8571e000 (-107689771147264) bytes_req=0x1000 (4096) bytes_alloc=0x1000 (4096) gfp_flags=0xcc0 (3264) node=0xffffffff (-1) accounted=(0)
4582.696629: kmem_cache_alloc: call_site=0xffffffff92d0250b (-1831852789) ptr=0xffff9e0e8577f800 (-107689770747904) bytes_req=0x168 (360) bytes_alloc=0x180 (384) gfp_flags=0xcc0 (3264) node=0xffffffff (-1) accounted=(0)
4582.696630: kmem_cache_alloc: call_site=0xffffffff92efca74 (-1829778828) ptr=0xffff9e0e8d35d3b0 (-107689640864848) bytes_req=0x10 (16) bytes_alloc=0x10 (16) gfp_flags=0xdc0 (3520) node=0xffffffff (-1) accounted=(0)
4582.696653: kmem_cache_free: call_site=0xffffffff92cfbea7 (-1831879001) ptr=0xffff9e0e8571e000 (-107689771147264) name=names_cache
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://lore.kernel.org/20241218141507.28389a1d@gandalf.local.home
Fixes: 07714b4bb3f98 ("tracing: Handle old buffer mappings for event strings and functions")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
An overflow occurred when performing the following calculation:
nr_pages = ((nr_subbufs + 1) << subbuf_order) - pgoff;
Add a check before the calculation to avoid this problem.
syzbot reported this as a slab-out-of-bounds in __rb_map_vma:
BUG: KASAN: slab-out-of-bounds in __rb_map_vma+0x9ab/0xae0 kernel/trace/ring_buffer.c:7058
Read of size 8 at addr ffff8880767dd2b8 by task syz-executor187/5836
CPU: 0 UID: 0 PID: 5836 Comm: syz-executor187 Not tainted 6.13.0-rc2-syzkaller-00159-gf932fb9b4074 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 11/25/2024
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:94 [inline]
dump_stack_lvl+0x116/0x1f0 lib/dump_stack.c:120
print_address_description mm/kasan/report.c:378 [inline]
print_report+0xc3/0x620 mm/kasan/report.c:489
kasan_report+0xd9/0x110 mm/kasan/report.c:602
__rb_map_vma+0x9ab/0xae0 kernel/trace/ring_buffer.c:7058
ring_buffer_map+0x56e/0x9b0 kernel/trace/ring_buffer.c:7138
tracing_buffers_mmap+0xa6/0x120 kernel/trace/trace.c:8482
call_mmap include/linux/fs.h:2183 [inline]
mmap_file mm/internal.h:124 [inline]
__mmap_new_file_vma mm/vma.c:2291 [inline]
__mmap_new_vma mm/vma.c:2355 [inline]
__mmap_region+0x1786/0x2670 mm/vma.c:2456
mmap_region+0x127/0x320 mm/mmap.c:1348
do_mmap+0xc00/0xfc0 mm/mmap.c:496
vm_mmap_pgoff+0x1ba/0x360 mm/util.c:580
ksys_mmap_pgoff+0x32c/0x5c0 mm/mmap.c:542
__do_sys_mmap arch/x86/kernel/sys_x86_64.c:89 [inline]
__se_sys_mmap arch/x86/kernel/sys_x86_64.c:82 [inline]
__x64_sys_mmap+0x125/0x190 arch/x86/kernel/sys_x86_64.c:82
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xcd/0x250 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x77/0x7f
The reproducer for this bug is:
------------------------8<-------------------------
#include <fcntl.h>
#include <stdlib.h>
#include <unistd.h>
#include <asm/types.h>
#include <sys/mman.h>
int main(int argc, char **argv)
{
int page_size = getpagesize();
int fd;
void *meta;
system("echo 1 > /sys/kernel/tracing/buffer_size_kb");
fd = open("/sys/kernel/tracing/per_cpu/cpu0/trace_pipe_raw", O_RDONLY);
meta = mmap(NULL, page_size, PROT_READ, MAP_SHARED, fd, page_size * 5);
}
------------------------>8-------------------------
Cc: stable@vger.kernel.org
Fixes: 117c39200d9d7 ("ring-buffer: Introducing ring-buffer mapping functions")
Link: https://lore.kernel.org/tencent_06924B6674ED771167C23CC336C097223609@qq.com
Reported-by: syzbot+345e4443a21200874b18@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=345e4443a21200874b18
Signed-off-by: Edward Adam Davis <eadavis@qq.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull tracing fixes from Steven Rostedt:
"Replace trace_check_vprintf() with test_event_printk() and
ignore_event()
The function test_event_printk() checks on boot up if the trace event
printf() formats dereference any pointers, and if they do, it then
looks at the arguments to make sure that the pointers they dereference
will exist in the event on the ring buffer. If they do not, it issues
a WARN_ON() as it is a likely bug.
But this isn't the case for the strings that can be dereferenced with
"%s", as some trace events (notably RCU and some IPI events) save a
pointer to a static string in the ring buffer. As the string it points
to lives as long as the kernel is running, it is not a bug to
reference it, as it is guaranteed to be there when the event is read.
But it is also possible (and a common bug) to point to some allocated
string that could be freed before the trace event is read and the
dereference is to bad memory. This case requires a run time check.
The previous way to handle this was with trace_check_vprintf() that
would process the printf format piece by piece and send what it didn't
care about to vsnprintf() to handle arguments that were not strings.
This kept it from having to reimplement vsnprintf(). But it relied on
va_list implementation and for architectures that copied the va_list
and did not pass it by reference, it wasn't even possible to do this
check and it would be skipped. As 64bit x86 passed va_list by
reference, most events were tested and this kept out bugs where
strings would have been dereferenced after being freed.
Instead of relying on the implementation of va_list, extend the boot
up test_event_printk() function to validate all the "%s" strings that
can be validated at boot, and for the few events that point to strings
outside the ring buffer, flag both the event and the field that is
dereferenced as "needs_test". Then before the event is printed, a call
to ignore_event() is made, and if the event has the flag set, it
iterates all its fields and for every field that is to be tested, it
will read the pointer directly from the event in the ring buffer and
make sure that it is valid. If the pointer is not valid, it will print
a WARN_ON(), print out to the trace that the event has unsafe memory
and ignore the print format.
With this new update, the trace_check_vprintf() can be safely removed
and now all events can be verified regardless of architecture"
* tag 'trace-v6.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
tracing: Check "%s" dereference via the field and not the TP_printk format
tracing: Add "%s" check in test_event_printk()
tracing: Add missing helper functions in event pointer dereference check
tracing: Fix test_event_printk() to process entire print argument
|
|
Third time's the charm, I hope?
Fixes: d3116756a710 ("drm/ttm: rename bo->mem and make it a pointer")
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3837
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Michel Dänzer <mdaenzer@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 695c2c745e5dff201b75da8a1d237ce403600d04)
Cc: stable@vger.kernel.org
|
|
The VM pointer might already be outdated when that function is called.
Use the PASID instead to gather the information instead.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 57f812d171af4ba233d3ed7c94dfa5b8e92dcc04)
Cc: stable@vger.kernel.org
|
|
Use the helper function rather than reading it directly.
Reviewed-by: Yang Wang <kevinyang.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 8f2cd1067afe68372a1723e05e19b68ed187676a)
Cc: stable@vger.kernel.org
|
|
Use the helper function rather than reading it directly.
Reviewed-by: Yang Wang <kevinyang.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit f1fd1d0f40272948aa6ab82a3a82ecbbc76dff53)
Cc: stable@vger.kernel.org
|
|
Use the helper function rather than reading it directly.
Reviewed-by: Yang Wang <kevinyang.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 63bfd24088b42c6f55c2096bfc41b50213d419b2)
Cc: stable@vger.kernel.org
|
|
Use the helper function rather than reading it directly.
Reviewed-by: Yang Wang <kevinyang.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 2c8eeaaa0fe5841ccf07a0eb51b1426f34ef39f7)
Cc: stable@vger.kernel.org
|
|
Use the helper function rather than reading it directly.
Reviewed-by: Yang Wang <kevinyang.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 22b9555bc90df22b585bdd1f161b61584b13af51)
Cc: stable@vger.kernel.org
|
|
A recent refactoring was identified by smatch to cause another potential NULL
dereference:
drivers/net/wireless/st/cw1200/cw1200_spi.c:440 cw1200_spi_disconnect() error: we previously assumed 'self' could be null (see line 433)
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/r/202411271742.Xa7CNVh1-lkp@intel.com/
Fixes: 2719a9e7156c ("wifi: cw1200: Convert to GPIO descriptors")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241217-cw1200-fix-v1-1-911e6b5823ec@linaro.org
|
|
Since 2320c9e6a768 ("drm/sched: memset() 'job' in drm_sched_job_init()")
accessing job->base.sched can produce unexpected results as the initialisation
of (*job)->base.sched done in amdgpu_job_alloc is overwritten by the
memset.
This commit fixes an issue when a CS would fail validation and would
be rejected after job->num_ibs is incremented. In this case,
amdgpu_ib_free(ring->adev, ...) will be called, which would crash the
machine because the ring value is bogus.
To fix this, pass a NULL pointer to amdgpu_ib_free(): we can do this
because the device is actually not used in this function.
The next commit will remove the ring argument completely.
Fixes: 2320c9e6a768 ("drm/sched: memset() 'job' in drm_sched_job_init()")
Signed-off-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 2ae520cb12831d264ceb97c61f72c59d33c0dbd7)
|
|
If the kernel hasn't been compiled with PCIe hotplug support this
can lead to problems with dGPUs that use BOCO because they effectively
drop off the bus.
To prevent issues, disable BOCO support when compiled without PCIe hotplug.
Reported-by: Gabriel Marcano <gabemarcano@yahoo.com>
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/1707#note_2696862
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://lore.kernel.org/r/20241211155601.3585256-1-superm1@kernel.org
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 1ad5bdc28bafa66db0f041cc6cdd278a80426aae)
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull hyperv fixes from Wei Liu:
- Various fixes to Hyper-V tools in the kernel tree (Dexuan Cui, Olaf
Hering, Vitaly Kuznetsov)
- Fix a bug in the Hyper-V TSC page based sched_clock() (Naman Jain)
- Two bug fixes in the Hyper-V utility functions (Michael Kelley)
- Convert open-coded timeouts to secs_to_jiffies() in Hyper-V drivers
(Easwar Hariharan)
* tag 'hyperv-fixes-signed-20241217' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
tools/hv: reduce resource usage in hv_kvp_daemon
tools/hv: add a .gitignore file
tools/hv: reduce resouce usage in hv_get_dns_info helper
hv/hv_kvp_daemon: Pass NIC name to hv_get_dns_info as well
Drivers: hv: util: Avoid accessing a ringbuffer not initialized yet
Drivers: hv: util: Don't force error code to ENODEV in util_probe()
tools/hv: terminate fcopy daemon if read from uio fails
drivers: hv: Convert open-coded timeouts to secs_to_jiffies()
tools: hv: change permissions of NetworkManager configuration file
x86/hyperv: Fix hv tsc page based sched_clock for hibernation
tools: hv: Fix a complier warning in the fcopy uio daemon
|
|
In 32-bit x86 builds CONFIG_STATIC_CALL_INLINE isn't set, leading to
static_call_initialized not being available.
Define it as "0" in that case.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Fixes: 0ef8047b737d ("x86/static-call: provide a way to do very early static-call updates")
Signed-off-by: Juergen Gross <jgross@suse.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
