summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2024-08-10irqchip/riscv-aplic: Retrigger MSI interrupt on source configurationYong-Xuan Wang
The section 4.5.2 of the RISC-V AIA specification says that "any write to a sourcecfg register of an APLIC might (or might not) cause the corresponding interrupt-pending bit to be set to one if the rectified input value is high (= 1) under the new source mode." When the interrupt type is changed in the sourcecfg register, the APLIC device might not set the corresponding pending bit, so the interrupt might never become pending. To handle sourcecfg register changes for level-triggered interrupts in MSI mode, manually set the pending bit for retriggering interrupt so it gets retriggered if it was already asserted. Fixes: ca8df97fe679 ("irqchip/riscv-aplic: Add support for MSI-mode") Signed-off-by: Yong-Xuan Wang <yongxuan.wang@sifive.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Vincent Chen <vincent.chen@sifive.com> Reviewed-by: Anup Patel <anup@brainfault.org> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/all/20240809071049.2454-1-yongxuan.wang@sifive.com
2024-08-10irqchip/xilinx: Fix shift out of boundsRadhey Shyam Pandey
The device tree property 'xlnx,kind-of-intr' is sanity checked that the bitmask contains only set bits which are in the range of the number of interrupts supported by the controller. The check is done by shifting the mask right by the number of supported interrupts and checking the result for zero. The data type of the mask is u32 and the number of supported interrupts is up to 32. In case of 32 interrupts the shift is out of bounds, resulting in a mismatch warning. The out of bounds condition is also reported by UBSAN: UBSAN: shift-out-of-bounds in irq-xilinx-intc.c:332:22 shift exponent 32 is too large for 32-bit type 'unsigned int' Fix it by promoting the mask to u64 for the test. Fixes: d50466c90724 ("microblaze: intc: Refactor DT sanity check") Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/all/1723186944-3571957-1-git-send-email-radhey.shyam.pandey@amd.com
2024-08-09Merge branch 'mlx5-misc-fixes-2024-08-08'Jakub Kicinski
Tariq Toukan says: ==================== mlx5 misc fixes 2024-08-08 This patchset provides misc bug fixes from the team to the mlx5 core and Eth drivers. ==================== Link: https://patch.msgid.link/20240808144107.2095424-1-tariqt@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-08-09net/mlx5e: Fix queue stats access to non-existing channels splatGal Pressman
The queue stats API queries the queues according to the real_num_[tr]x_queues, in case the device is down and channels were not yet created, don't try to query their statistics. To trigger the panic, run this command before the interface is brought up: ./cli.py --spec ../../../Documentation/netlink/specs/netdev.yaml --dump qstats-get --json '{"ifindex": 4}' BUG: kernel NULL pointer dereference, address: 0000000000000c00 PGD 0 P4D 0 Oops: Oops: 0000 [#1] SMP PTI CPU: 3 UID: 0 PID: 977 Comm: python3 Not tainted 6.10.0+ #40 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014 RIP: 0010:mlx5e_get_queue_stats_rx+0x3c/0xb0 [mlx5_core] Code: fc 55 48 63 ee 53 48 89 d3 e8 40 3d 70 e1 85 c0 74 58 4c 89 ef e8 d4 07 04 00 84 c0 75 41 49 8b 84 24 f8 39 00 00 48 8b 04 e8 <48> 8b 90 00 0c 00 00 48 03 90 40 0a 00 00 48 89 53 08 48 8b 90 08 RSP: 0018:ffff888116be37d0 EFLAGS: 00010246 RAX: 0000000000000000 RBX: ffff888116be3868 RCX: 0000000000000004 RDX: ffff88810ada4000 RSI: 0000000000000000 RDI: ffff888109df09c0 RBP: 0000000000000000 R08: 0000000000000004 R09: 0000000000000004 R10: ffff88813461901c R11: ffffffffffffffff R12: ffff888109df0000 R13: ffff888109df09c0 R14: ffff888116be38d0 R15: 0000000000000000 FS: 00007f4375d5c740(0000) GS:ffff88852c980000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000c00 CR3: 0000000106ada006 CR4: 0000000000370eb0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> ? __die+0x1f/0x60 ? page_fault_oops+0x14e/0x3d0 ? exc_page_fault+0x73/0x130 ? asm_exc_page_fault+0x22/0x30 ? mlx5e_get_queue_stats_rx+0x3c/0xb0 [mlx5_core] netdev_nl_stats_by_netdev+0x2a6/0x4c0 ? __rmqueue_pcplist+0x351/0x6f0 netdev_nl_qstats_get_dumpit+0xc4/0x1b0 genl_dumpit+0x2d/0x80 netlink_dump+0x199/0x410 __netlink_dump_start+0x1aa/0x2c0 genl_family_rcv_msg_dumpit+0x94/0xf0 ? __pfx_genl_start+0x10/0x10 ? __pfx_genl_dumpit+0x10/0x10 ? __pfx_genl_done+0x10/0x10 genl_rcv_msg+0x116/0x2b0 ? __pfx_netdev_nl_qstats_get_dumpit+0x10/0x10 ? __pfx_genl_rcv_msg+0x10/0x10 netlink_rcv_skb+0x54/0x100 genl_rcv+0x24/0x40 netlink_unicast+0x21a/0x340 netlink_sendmsg+0x1f4/0x440 __sys_sendto+0x1b6/0x1c0 ? do_sock_setsockopt+0xc3/0x180 ? __sys_setsockopt+0x60/0xb0 __x64_sys_sendto+0x20/0x30 do_syscall_64+0x50/0x110 entry_SYSCALL_64_after_hwframe+0x76/0x7e RIP: 0033:0x7f43757132b0 Code: c0 ff ff ff ff eb b8 0f 1f 00 f3 0f 1e fa 41 89 ca 64 8b 04 25 18 00 00 00 85 c0 75 1d 45 31 c9 45 31 c0 b8 2c 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 68 c3 0f 1f 80 00 00 00 00 41 54 48 83 ec 20 RSP: 002b:00007ffd258da048 EFLAGS: 00000246 ORIG_RAX: 000000000000002c RAX: ffffffffffffffda RBX: 00007ffd258da0f8 RCX: 00007f43757132b0 RDX: 000000000000001c RSI: 00007f437464b850 RDI: 0000000000000003 RBP: 00007f4375085de0 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000 R13: ffffffffc4653600 R14: 0000000000000001 R15: 00007f43751a6147 </TASK> Modules linked in: netconsole xt_conntrack xt_MASQUERADE nf_conntrack_netlink nfnetlink xt_addrtype iptable_nat nf_nat br_netfilter rpcsec_gss_krb5 auth_rpcgss oid_registry overlay rpcrdma rdma_ucm ib_iser libiscsi scsi_transport_iscsi ib_umad rdma_cm ib_ipoib iw_cm ib_cm mlx5_ib ib_uverbs ib_core zram zsmalloc mlx5_core fuse [last unloaded: netconsole] CR2: 0000000000000c00 ---[ end trace 0000000000000000 ]--- RIP: 0010:mlx5e_get_queue_stats_rx+0x3c/0xb0 [mlx5_core] Code: fc 55 48 63 ee 53 48 89 d3 e8 40 3d 70 e1 85 c0 74 58 4c 89 ef e8 d4 07 04 00 84 c0 75 41 49 8b 84 24 f8 39 00 00 48 8b 04 e8 <48> 8b 90 00 0c 00 00 48 03 90 40 0a 00 00 48 89 53 08 48 8b 90 08 RSP: 0018:ffff888116be37d0 EFLAGS: 00010246 RAX: 0000000000000000 RBX: ffff888116be3868 RCX: 0000000000000004 RDX: ffff88810ada4000 RSI: 0000000000000000 RDI: ffff888109df09c0 RBP: 0000000000000000 R08: 0000000000000004 R09: 0000000000000004 R10: ffff88813461901c R11: ffffffffffffffff R12: ffff888109df0000 R13: ffff888109df09c0 R14: ffff888116be38d0 R15: 0000000000000000 FS: 00007f4375d5c740(0000) GS:ffff88852c980000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000c00 CR3: 0000000106ada006 CR4: 0000000000370eb0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Fixes: 7b66ae536a78 ("net/mlx5e: Add per queue netdev-genl stats") Signed-off-by: Gal Pressman <gal@nvidia.com> Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Reviewed-by: Joe Damato <jdamato@fastly.com> Link: https://patch.msgid.link/20240808144107.2095424-6-tariqt@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-08-09net/mlx5e: Correctly report errors for ethtool rx flowsCosmin Ratiu
Previously, an ethtool rx flow with no attrs would not be added to the NIC as it has no rules to configure the hw with, but it would be reported as successful to the caller (return code 0). This is confusing for the user as ethtool then reports "Added rule $num", but no rule was actually added. This change corrects that by instead reporting these wrong rules as -EINVAL. Fixes: b29c61dac3a2 ("net/mlx5e: Ethtool steering flow validation refactoring") Signed-off-by: Cosmin Ratiu <cratiu@nvidia.com> Reviewed-by: Saeed Mahameed <saeedm@nvidia.com> Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com> Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Link: https://patch.msgid.link/20240808144107.2095424-5-tariqt@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-08-09net/mlx5e: Take state lock during tx timeout reporterDragos Tatulea
mlx5e_safe_reopen_channels() requires the state lock taken. The referenced changed in the Fixes tag removed the lock to fix another issue. This patch adds it back but at a later point (when calling mlx5e_safe_reopen_channels()) to avoid the deadlock referenced in the Fixes tag. Fixes: eab0da38912e ("net/mlx5e: Fix possible deadlock on mlx5e_tx_timeout_work") Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com> Link: https://lore.kernel.org/all/ZplpKq8FKi3vwfxv@gmail.com/T/ Reviewed-by: Breno Leitao <leitao@debian.org> Reviewed-by: Moshe Shemesh <moshe@nvidia.com> Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Link: https://patch.msgid.link/20240808144107.2095424-4-tariqt@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-08-09net/mlx5e: SHAMPO, Increase timeout to improve latencyDragos Tatulea
During latency tests (netperf TCP_RR) a 30% degradation of HW GRO vs SW GRO was observed. This is due to SHAMPO triggering timeout filler CQEs instead of delivering the CQE for the packet. Having a short timeout for SHAMPO doesn't bring any benefits as it is the driver that does the merging, not the hardware. On the contrary, it can have a negative impact: additional filler CQEs are generated due to the timeout. As there is no way to disable this timeout, this change sets it to the maximum value. Instead of using the packet_merge.timeout parameter which is also used for LRO, set the value directly when filling in the rest of the SHAMPO parameters in mlx5e_build_rq_param(). Fixes: 99be56171fa9 ("net/mlx5e: SHAMPO, Re-enable HW-GRO") Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com> Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Link: https://patch.msgid.link/20240808144107.2095424-3-tariqt@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-08-09net/mlx5: SD, Do not query MPIR register if no sd_groupTariq Toukan
Unconditionally calling the MPIR query on BF separate mode yields the FW syndrome below [1]. Do not call it unless admin clearly specified the SD group, i.e. expressing the intention of using the multi-PF netdev feature. This fix covers cases not covered in commit fca3b4791850 ("net/mlx5: Do not query MPIR on embedded CPU function"). [1] mlx5_cmd_out_err:808:(pid 8267): ACCESS_REG(0x805) op_mod(0x1) failed, status bad system state(0x4), syndrome (0x685f19), err(-5) Fixes: 678eb448055a ("net/mlx5: SD, Implement basic query and instantiation") Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Reviewed-by: Gal Pressman <gal@nvidia.com> Link: https://patch.msgid.link/20240808144107.2095424-2-tariqt@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-08-09Merge branch ↵Jakub Kicinski
'don-t-take-hw-uso-path-when-packets-can-t-be-checksummed-by-device' Jakub Sitnicki says: ==================== Don't take HW USO path when packets can't be checksummed by device This series addresses a recent regression report from syzbot [1]. After enabling UDP_SEGMENT for egress devices which don't support checksum offload [2], we need to tighten down the checks which let packets take the HW USO path. The fix consists of two parts: 1. don't let devices offer USO without checksum offload, and 2. force software USO fallback in presence of IPv6 extension headers. [1] https://lore.kernel.org/all/000000000000e1609a061d5330ce@google.com/ [2] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=10154dbded6d6a2fecaebdfda206609de0f121a9 v3: https://lore.kernel.org/r/20240807-udp-gso-egress-from-tunnel-v3-0-8828d93c5b45@cloudflare.com v2: https://lore.kernel.org/r/20240801-udp-gso-egress-from-tunnel-v2-0-9a2af2f15d8d@cloudflare.com v1: https://lore.kernel.org/r/20240725-udp-gso-egress-from-tunnel-v1-0-5e5530ead524@cloudflare.com ==================== Link: https://patch.msgid.link/20240808-udp-gso-egress-from-tunnel-v4-0-f5c5b4149ab9@cloudflare.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-08-09selftests/net: Add coverage for UDP GSO with IPv6 extension headersJakub Sitnicki
After enabling UDP GSO for devices not offering checksum offload, we have hit a regression where a bad offload warning can be triggered when sending a datagram with IPv6 extension headers. Extend the UDP GSO IPv6 tests to cover this scenario. Reviewed-by: Willem de Bruijn <willemb@google.com> Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com> Link: https://patch.msgid.link/20240808-udp-gso-egress-from-tunnel-v4-3-f5c5b4149ab9@cloudflare.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-08-09udp: Fall back to software USO if IPv6 extension headers are presentJakub Sitnicki
In commit 10154dbded6d ("udp: Allow GSO transmit from devices with no checksum offload") we have intentionally allowed UDP GSO packets marked CHECKSUM_NONE to pass to the GSO stack, so that they can be segmented and checksummed by a software fallback when the egress device lacks these features. What was not taken into consideration is that a CHECKSUM_NONE skb can be handed over to the GSO stack also when the egress device advertises the tx-udp-segmentation / NETIF_F_GSO_UDP_L4 feature. This will happen when there are IPv6 extension headers present, which we check for in __ip6_append_data(). Syzbot has discovered this scenario, producing a warning as below: ip6tnl0: caps=(0x00000006401d7869, 0x00000006401d7869) WARNING: CPU: 0 PID: 5112 at net/core/dev.c:3293 skb_warn_bad_offload+0x166/0x1a0 net/core/dev.c:3291 Modules linked in: CPU: 0 PID: 5112 Comm: syz-executor391 Not tainted 6.10.0-rc7-syzkaller-01603-g80ab5445da62 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 06/07/2024 RIP: 0010:skb_warn_bad_offload+0x166/0x1a0 net/core/dev.c:3291 [...] Call Trace: <TASK> __skb_gso_segment+0x3be/0x4c0 net/core/gso.c:127 skb_gso_segment include/net/gso.h:83 [inline] validate_xmit_skb+0x585/0x1120 net/core/dev.c:3661 __dev_queue_xmit+0x17a4/0x3e90 net/core/dev.c:4415 neigh_output include/net/neighbour.h:542 [inline] ip6_finish_output2+0xffa/0x1680 net/ipv6/ip6_output.c:137 ip6_finish_output+0x41e/0x810 net/ipv6/ip6_output.c:222 ip6_send_skb+0x112/0x230 net/ipv6/ip6_output.c:1958 udp_v6_send_skb+0xbf5/0x1870 net/ipv6/udp.c:1292 udpv6_sendmsg+0x23b3/0x3270 net/ipv6/udp.c:1588 sock_sendmsg_nosec net/socket.c:730 [inline] __sock_sendmsg+0xef/0x270 net/socket.c:745 ____sys_sendmsg+0x525/0x7d0 net/socket.c:2585 ___sys_sendmsg net/socket.c:2639 [inline] __sys_sendmmsg+0x3b2/0x740 net/socket.c:2725 __do_sys_sendmmsg net/socket.c:2754 [inline] __se_sys_sendmmsg net/socket.c:2751 [inline] __x64_sys_sendmmsg+0xa0/0xb0 net/socket.c:2751 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f [...] </TASK> We are hitting the bad offload warning because when an egress device is capable of handling segmentation offload requested by skb_shinfo(skb)->gso_type, the chain of gso_segment callbacks won't produce any segment skbs and return NULL. See the skb_gso_ok() branch in {__udp,tcp,sctp}_gso_segment helpers. To fix it, force a fallback to software USO when processing a packet with IPv6 extension headers, since we don't know if these can checksummed by all devices which offer USO. Fixes: 10154dbded6d ("udp: Allow GSO transmit from devices with no checksum offload") Reported-by: syzbot+e15b7e15b8a751a91d9a@syzkaller.appspotmail.com Closes: https://lore.kernel.org/all/000000000000e1609a061d5330ce@google.com/ Reviewed-by: Willem de Bruijn <willemb@google.com> Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com> Link: https://patch.msgid.link/20240808-udp-gso-egress-from-tunnel-v4-2-f5c5b4149ab9@cloudflare.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-08-09net: Make USO depend on CSUM offloadJakub Sitnicki
UDP segmentation offload inherently depends on checksum offload. It should not be possible to disable checksum offload while leaving USO enabled. Enforce this dependency in code. There is a single tx-udp-segmentation feature flag to indicate support for both IPv4/6, hence the devices wishing to support USO must offer checksum offload for both IP versions. Fixes: 10154dbded6d ("udp: Allow GSO transmit from devices with no checksum offload") Suggested-by: Willem de Bruijn <willemdebruijn.kernel@gmail.com> Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Link: https://patch.msgid.link/20240808-udp-gso-egress-from-tunnel-v4-1-f5c5b4149ab9@cloudflare.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-08-09gtp: pull network headers in gtp_dev_xmit()Eric Dumazet
syzbot/KMSAN reported use of uninit-value in get_dev_xmit() [1] We must make sure the IPv4 or Ipv6 header is pulled in skb->head before accessing fields in them. Use pskb_inet_may_pull() to fix this issue. [1] BUG: KMSAN: uninit-value in ipv6_pdp_find drivers/net/gtp.c:220 [inline] BUG: KMSAN: uninit-value in gtp_build_skb_ip6 drivers/net/gtp.c:1229 [inline] BUG: KMSAN: uninit-value in gtp_dev_xmit+0x1424/0x2540 drivers/net/gtp.c:1281 ipv6_pdp_find drivers/net/gtp.c:220 [inline] gtp_build_skb_ip6 drivers/net/gtp.c:1229 [inline] gtp_dev_xmit+0x1424/0x2540 drivers/net/gtp.c:1281 __netdev_start_xmit include/linux/netdevice.h:4913 [inline] netdev_start_xmit include/linux/netdevice.h:4922 [inline] xmit_one net/core/dev.c:3580 [inline] dev_hard_start_xmit+0x247/0xa20 net/core/dev.c:3596 __dev_queue_xmit+0x358c/0x5610 net/core/dev.c:4423 dev_queue_xmit include/linux/netdevice.h:3105 [inline] packet_xmit+0x9c/0x6c0 net/packet/af_packet.c:276 packet_snd net/packet/af_packet.c:3145 [inline] packet_sendmsg+0x90e3/0xa3a0 net/packet/af_packet.c:3177 sock_sendmsg_nosec net/socket.c:730 [inline] __sock_sendmsg+0x30f/0x380 net/socket.c:745 __sys_sendto+0x685/0x830 net/socket.c:2204 __do_sys_sendto net/socket.c:2216 [inline] __se_sys_sendto net/socket.c:2212 [inline] __x64_sys_sendto+0x125/0x1d0 net/socket.c:2212 x64_sys_call+0x3799/0x3c10 arch/x86/include/generated/asm/syscalls_64.h:45 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xcd/0x1e0 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f Uninit was created at: slab_post_alloc_hook mm/slub.c:3994 [inline] slab_alloc_node mm/slub.c:4037 [inline] kmem_cache_alloc_node_noprof+0x6bf/0xb80 mm/slub.c:4080 kmalloc_reserve+0x13d/0x4a0 net/core/skbuff.c:583 __alloc_skb+0x363/0x7b0 net/core/skbuff.c:674 alloc_skb include/linux/skbuff.h:1320 [inline] alloc_skb_with_frags+0xc8/0xbf0 net/core/skbuff.c:6526 sock_alloc_send_pskb+0xa81/0xbf0 net/core/sock.c:2815 packet_alloc_skb net/packet/af_packet.c:2994 [inline] packet_snd net/packet/af_packet.c:3088 [inline] packet_sendmsg+0x749c/0xa3a0 net/packet/af_packet.c:3177 sock_sendmsg_nosec net/socket.c:730 [inline] __sock_sendmsg+0x30f/0x380 net/socket.c:745 __sys_sendto+0x685/0x830 net/socket.c:2204 __do_sys_sendto net/socket.c:2216 [inline] __se_sys_sendto net/socket.c:2212 [inline] __x64_sys_sendto+0x125/0x1d0 net/socket.c:2212 x64_sys_call+0x3799/0x3c10 arch/x86/include/generated/asm/syscalls_64.h:45 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xcd/0x1e0 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f CPU: 0 UID: 0 PID: 7115 Comm: syz.1.515 Not tainted 6.11.0-rc1-syzkaller-00043-g94ede2a3e913 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 06/27/2024 Fixes: 999cb275c807 ("gtp: add IPv6 support") Fixes: 459aa660eb1d ("gtp: add initial driver for datapath of GPRS Tunneling Protocol (GTP-U)") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Harald Welte <laforge@gnumonks.org> Reviewed-by: Pablo Neira Ayuso <pablo@netfilter.org> Link: https://patch.msgid.link/20240808132455.3413916-1-edumazet@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-08-09Merge tag '6.11-rc2-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6Linus Torvalds
Pull smb client fixes from Steve French: - DFS fix - fix for security flags for requiring encryption - minor cleanup * tag '6.11-rc2-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6: cifs: cifs_inval_name_dfs_link_error: correct the check for fullpath Fix spelling errors in Server Message Block smb3: fix setting SecurityFlags when encryption is required
2024-08-09Merge tag 'spi-fix-v6.11-rc2' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi Pull spi fixes from Mark Brown: "A few SPI fixes: clock rate calculation fixes for the Kunpeng and lpsi drivers and a missing registration of a device ID for spidev (which had only been updated for DT cases, causing warnings)" * tag 'spi-fix-v6.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: spi: spi-fsl-lpspi: Fix scldiv calculation spi: spidev: Add missing spi_device_id for bh2228fv spi: hisi-kunpeng: Add verification for the max_frequency provided by the firmware spi: hisi-kunpeng: Add validation for the minimum value of speed_hz
2024-08-09binfmt_flat: Fix corruption when not offsetting data startKees Cook
Commit 04d82a6d0881 ("binfmt_flat: allow not offsetting data start") introduced a RISC-V specific variant of the FLAT format which does not allocate any space for the (obsolete) array of shared library pointers. However, it did not disable the code which initializes the array, resulting in the corruption of sizeof(long) bytes before the DATA segment, generally the end of the TEXT segment. Introduce MAX_SHARED_LIBS_UPDATE which depends on the state of CONFIG_BINFMT_FLAT_NO_DATA_START_OFFSET to guard the initialization of the shared library pointer region so that it will only be initialized if space is reserved for it. Fixes: 04d82a6d0881 ("binfmt_flat: allow not offsetting data start") Co-developed-by: Stefan O'Rear <sorear@fastmail.com> Signed-off-by: Stefan O'Rear <sorear@fastmail.com> Reviewed-by: Damien Le Moal <dlemoal@kernel.org> Acked-by: Greg Ungerer <gerg@linux-m68k.org> Link: https://lore.kernel.org/r/20240807195119.it.782-kees@kernel.org Signed-off-by: Kees Cook <kees@kernel.org>
2024-08-09bcachefs: bcachefs_metadata_version_disk_accounting_v3Kent Overstreet
bcachefs_metadata_version_disk_accounting_v2 erroneously had padding bytes in disk_accounting_key, which is a problem because we have to guarantee that all unused bytes in disk_accounting_key are zeroed. Fortunately 6.11 isn't out yet, so it's cheap to fix this by spinning a new version. Reported-by: Gabriel de Perthuis <g2p.code@gmail.com> Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
2024-08-09Merge tag 'drm-fixes-2024-08-10' of https://gitlab.freedesktop.org/drm/kernelLinus Torvalds
Pull drm fixes from Dave Airlie: "Weekly regular fixes, mostly amdgpu with i915/xe having a few each, and then some misc bits across the board, seems about right for rc3 time. client: - fix null ptr deref bridge: - connector: fix double free atomic: - fix async flip update panel: - document panel omap: - add config dependency tests: - fix gem shmem test drm buddy: - Add start address to trim function amdgpu: - DMCUB fix - Fix DET programming on some DCNs - DCC fixes - DCN 4.0.1 fixes - SMU 14.0.x update - MMHUB fix - DCN 3.1.4 fix - GC 12.0 fixes - Fix soft recovery error propogation - SDMA 7.0 fixes - DSC fix xe: - Fix off-by-one when processing RTP rules - Use dma_fence_chain_free in chain fence unused as a sync - Fix PL1 disable flow in xe_hwmon_power_max_write - Take ref to VM in delayed dump snapshot i915: - correct dual pps handling for MTL_PCH+ [display] - Adjust vma offset for framebuffer mmap offset [gem] - Fix Virtual Memory mapping boundaries calculation [gem] - Allow evicting to use the requested placement - Attempt to get pages without eviction first" * tag 'drm-fixes-2024-08-10' of https://gitlab.freedesktop.org/drm/kernel: (31 commits) drm/xe: Take ref to VM in delayed snapshot drm/xe/hwmon: Fix PL1 disable flow in xe_hwmon_power_max_write drm/xe: Use dma_fence_chain_free in chain fence unused as a sync drm/xe/rtp: Fix off-by-one when processing rules drm/amdgpu: Add DCC GFX12 flag to enable address alignment drm/amdgpu: correct sdma7 max dw drm/amdgpu: Add address alignment support to DCC buffers drm/amd/display: Skip Recompute DSC Params if no Stream on Link drm/amdgpu: change non-dcc buffer copy configuration drm/amdgpu: Forward soft recovery errors to userspace drm/amdgpu: add golden setting for gc v12 drm/buddy: Add start address support to trim function drm/amd/display: Add missing program DET segment call to pipe init drm/amd/display: Add missing DCN314 to the DML Makefile drm/amdgpu: force to use legacy inv in mmhub drm/amd/pm: update powerplay structure on smu v14.0.2/3 drm/amd/display: Add missing mcache registers drm/amd/display: Add dcc propagation value drm/amd/display: Add missing DET segments programming drm/amd/display: Replace dm_execute_dmub_cmd with dc_wake_and_execute_dmub_cmd ...
2024-08-09bcachefs: improve bch2_dev_usage_to_text()Kent Overstreet
Add a line for capacity Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
2024-08-09bcachefs: bch2_accounting_invalid()Kent Overstreet
Implement bch2_accounting_invalid(); check for junk at the end, and replicas accounting entries in particular need to be checked or we'll pop asserts later. Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
2024-08-09Merge tag 'bitmap-6.11-rc' of https://github.com/norov/linuxLinus Torvalds
Pull cpumask fix from Yury Norov: "Fix for cpumask merge" [ Mea culpa, this was my mismerge due to too much cut-and-paste - Linus ] * tag 'bitmap-6.11-rc' of https://github.com/norov/linux: cpumask: Fix crash on updating CPU enabled mask
2024-08-09Merge tag 'pm-6.11-rc3' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm Pull power management fix from Rafael Wysocki: "Change the default EPP (energy-performence preference) value for the Emerald Rapids processor in the intel_pstate driver. Thisshould improve both the performance and energy efficiency (Pedro Henrique Kopper)" * tag 'pm-6.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: cpufreq: intel_pstate: Update Balance performance EPP for Emerald Rapids
2024-08-09Merge tag 'asm-generic-fixes-6.11-2' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic Pull asm-generic fixes from Arnd Bergmann: "There are two more changes to the syscall.tbl conversion: the '__NR_newfstat' in the previous bugfix was a mistake and gets reverted now, after triple-checking that the contents are now back to what they were on all architectures. The __NR_nfsservctl definition is not really needed but came up in the same discussion as it had previously been defined in uapi/asm-generic/unistd.h and tested for in user space. There are a few more symbols that used to be defined in the old unistd.h file, but that are never defined on any other architecture using syscall.tbl format. These used to be needed inside of the kernel: __NR_syscalls __NR_arch_specific_syscall __NR3264_* Searching for these on https://codesearch.debian.net/ shows a few packages (rustc, golang, clamav, libseccomp, librsvg, strace) that duplicate all the macros from asm/unistd.h, but nothing that actually uses the macros, so I concluded that they are fine to omit after all" * tag 'asm-generic-fixes-6.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic: syscalls: add back legacy __NR_nfsservctl macro syscalls: fix fstat() entry again
2024-08-09Merge tag 'arm-fixes-6.11-1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc Pull ARM SoC fixes from Arnd Bergmann: "There are three sets of patches for the soc tree: - Marek Behún addresses multiple build time regressions caused by changes to the cznic turris-omnia support - Dmitry Torokhov fixes a regression in the legacy "gumstix" board code he cleaned up earlier - The TI K3 maintainers found multiple bugs in the in gpio, audio and pcie devicetree nodes" * tag 'arm-fixes-6.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: ARM: pxa/gumstix: fix attaching properties to vbus gpio device doc: platform: cznic: turris-omnia-mcu: Use double backticks for attribute value doc: platform: cznic: turris-omnia-mcu: Fix sphinx-build warning platform: cznic: turris-omnia-mcu: Make GPIO code optional platform: cznic: turris-omnia-mcu: Make poweroff and wakeup code optional platform: cznic: turris-omnia-mcu: Make TRNG code optional platform: cznic: turris-omnia-mcu: Make watchdog code optional arm64: dts: ti: k3-j784s4-main: Correct McASP DMAs arm64: dts: ti: k3-j722s: Fix gpio-range for main_pmx0 arm64: dts: ti: k3-am62p: Fix gpio-range for main_pmx0 arm64: dts: ti: k3-am62p: Add gpio-ranges for mcu_gpio0 arm64: dts: ti: k3-am62-verdin-dahlia: Keep CTRL_SLEEP_MOCI# regulator on arm64: dts: ti: k3-j784s4-evm: Consolidate serdes0 references arm64: dts: ti: k3-j784s4-evm: Assign only lanes 0 and 1 to PCIe1
2024-08-09Merge tag 'probes-fixes-v6.11-rc2' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace Pull kprobe fixes from Masami Hiramatsu: - Fix misusing str_has_prefix() parameter order to check symbol prefix correctly - bpf: remove unused declaring of bpf_kprobe_override * tag 'probes-fixes-v6.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace: kprobes: Fix to check symbol prefixes correctly bpf: kprobe: remove unused declaring of bpf_kprobe_override
2024-08-09Merge tag 'block-6.11-20240809' of git://git.kernel.dk/linuxLinus Torvalds
Pull block fixes from Jens Axboe: "Just a set of cleanups for blk-throttle and nvme structures" * tag 'block-6.11-20240809' of git://git.kernel.dk/linux: nvme: reorganize nvme_ns_head fields nvme: change data type of lba_shift nvme: remove a field from nvme_ns_head nvme: remove unused parameter blk-throttle: remove more latency dead-code
2024-08-09Merge tag 'io_uring-6.11-20240809' of git://git.kernel.dk/linuxLinus Torvalds
Pull io_uring fixes from Jens Axboe: "Nothing major in here, just two fixes for ensuring that bundle recv/send requests always get marked for cleanups, and a single fix to ensure that sends with provided buffers only pick a single buffer unless the bundle option has been enabled" * tag 'io_uring-6.11-20240809' of git://git.kernel.dk/linux: io_uring/net: don't pick multiple buffers for non-bundle send io_uring/net: ensure expanded bundle send gets marked for cleanup io_uring/net: ensure expanded bundle recv gets marked for cleanup
2024-08-09Merge tag 'sound-6.11-rc3' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound Pull sound fixes from Takashi Iwai: "A collection of lots of small changes, almost all device-specific: - A series of fixes for ASoC Qualcomm stuff - Various fixes for Cirrus ASoC and HD-audio codecs - A few AMD ASoC quirks and usual HD-audio quirks - Other misc fixes, including a long-time regression in USB-audio" * tag 'sound-6.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (39 commits) ASoC: cs35l56: Patch CS35L56_IRQ1_MASK_18 to the default value ASoC: meson: axg-fifo: fix irq scheduling issue with PREEMPT_RT MAINTAINERS: Update Cirrus Logic parts to linux-sound mailing list ASoC: dt-bindings: qcom,wcd939x: Correct reset GPIO polarity in example ASoC: dt-bindings: qcom,wcd938x: Correct reset GPIO polarity in example ASoC: dt-bindings: qcom,wcd934x: Correct reset GPIO polarity in example ASoC: dt-bindings: qcom,wcd937x: Correct reset GPIO polarity in example ASoC: amd: yc: Add quirk entry for OMEN by HP Gaming Laptop 16-n0xxx ASoC: codecs: ES8326: button detect issue ASoC: amd: yc: Support mic on Lenovo Thinkpad E14 Gen 6 ALSA: usb-audio: Re-add ScratchAmp quirk entries ALSA: hda/realtek: Add Framework Laptop 13 (Intel Core Ultra) to quirks ALSA: hda/hdmi: Yet more pin fix for HP EliteDesk 800 G4 ALSA: hda: Add HP MP9 G4 Retail System AMS to force connect list ASoC: cs35l56: Handle OTP read latency over SoundWire ASoC: codecs: lpass-macro: fix missing codec version ALSA: line6: Fix racy access to midibuf ASoC: cs-amp-lib: Fix NULL pointer crash if efi.get_variable is NULL ASoC: cs35l56: Stop creating ALSA controls for firmware coefficients ASoC: wm_adsp: Add control_add callback and export wm_adsp_control_add() ...
2024-08-09module: make waiting for a concurrent module loader interruptibleLinus Torvalds
The recursive aes-arm-bs module load situation reported by Russell King is getting fixed in the crypto layer, but this in the meantime fixes the "recursive load hangs forever" by just making the waiting for the first module load be interruptible. This should now match the old behavior before commit 9b9879fc0327 ("modules: catch concurrent module loads, treat them as idempotent"), which used the different "wait for module to be ready" code in module_patient_check_exists(). End result: a recursive module load will still block, but now a signal will interrupt it and fail the second module load, at which point the first module will successfully complete loading. Fixes: 9b9879fc0327 ("modules: catch concurrent module loads, treat them as idempotent") Cc: Russell King <linux@armlinux.org.uk> Cc: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2024-08-09Merge tag 'i2c-host-fixes-6.11-rc3' of ↵Wolfram Sang
git://git.kernel.org/pub/scm/linux/kernel/git/andi.shyti/linux into i2c/for-current Two fixes on the Qualcomm GENI I2C controller are cleaning up the error exit patch in the runtime_resume() function. The first is disabling the clock, the second disables the icc on the way out.
2024-08-09usbnet: ipheth: fix carrier detection in modes 1 and 4Foster Snowhill
Apart from the standard "configurations", "interfaces" and "alternate interface settings" in USB, iOS devices also have a notion of "modes". In different modes, the device exposes a different set of available configurations. Depending on the iOS version, and depending on the current mode, the length and contents of the carrier state control message differs: * 1 byte (seen on iOS 4.2.1, 8.4): * 03: carrier off (mode 0) * 04: carrier on (mode 0) * 3 bytes (seen on iOS 10.3.4, 15.7.6): * 03 03 03: carrier off (mode 0) * 04 04 03: carrier on (mode 0) * 4 bytes (seen on iOS 16.5, 17.6): * 03 03 03 00: carrier off (mode 0) * 04 03 03 00: carrier off (mode 1) * 06 03 03 00: carrier off (mode 4) * 04 04 03 04: carrier on (mode 0 and 1) * 06 04 03 04: carrier on (mode 4) Before this change, the driver always used the first byte of the response to determine carrier state. From this larger sample, the first byte seems to indicate the number of available USB configurations in the current mode (with the exception of the default mode 0), and in some cases (namely mode 1 and 4) does not correlate with the carrier state. Previous logic erroneously counted `04 03 03 00` as "carrier on" and `06 04 03 04` as "carrier off" on iOS versions that support mode 1 and mode 4 respectively. Only modes 0, 1 and 4 expose the USB Ethernet interfaces necessary for the ipheth driver. Check the second byte of the control message where possible, and fall back to checking the first byte on older iOS versions. Signed-off-by: Foster Snowhill <forst@pen.gy> Tested-by: Georgi Valkov <gvalkov@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-08-09usbnet: ipheth: do not stop RX on failing RX callbackFoster Snowhill
RX callbacks can fail for multiple reasons: * Payload too short * Payload formatted incorrecly (e.g. bad NCM framing) * Lack of memory None of these should cause the driver to seize up. Make such failures non-critical and continue processing further incoming URBs. Signed-off-by: Foster Snowhill <forst@pen.gy> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-08-09usbnet: ipheth: drop RX URBs with no payloadFoster Snowhill
On iPhone 15 Pro Max one can observe periodic URBs with no payload on the "bulk in" (RX) endpoint. These don't seem to do anything meaningful. Reproduced on iOS 17.5.1 and 17.6. This behaviour isn't observed on iPhone 11 on the same iOS version. The nature of these zero-length URBs is so far unknown. Drop RX URBs with no payload. Signed-off-by: Foster Snowhill <forst@pen.gy> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-08-09usbnet: ipheth: remove extraneous rx URB length checkFoster Snowhill
Rx URB length was already checked in ipheth_rcvbulk_callback_legacy() and ipheth_rcvbulk_callback_ncm(), depending on the current mode. The check in ipheth_rcvbulk_callback() was thus mostly a duplicate. The only place in ipheth_rcvbulk_callback() where we care about the URB length is for the initial control frame. These frames are always 4 bytes long. This has been checked as far back as iOS 4.2.1 on iPhone 3G. Remove the extraneous URB length check. For control frames, check for the specific 4-byte length instead. Signed-off-by: Foster Snowhill <forst@pen.gy> Tested-by: Georgi Valkov <gvalkov@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-08-09usbnet: ipheth: race between ipheth_close and error handlingOliver Neukum
ipheth_sndbulk_callback() can submit carrier_work as a part of its error handling. That means that the driver must make sure that the work is cancelled after it has made sure that no more URB can terminate with an error condition. Hence the order of actions in ipheth_close() needs to be inverted. Signed-off-by: Oliver Neukum <oneukum@suse.com> Signed-off-by: Foster Snowhill <forst@pen.gy> Tested-by: Georgi Valkov <gvalkov@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-08-09Merge tag 'asoc-fix-v6.11-rc2' of ↵Takashi Iwai
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus ASoC: Fixes for v6.11 Quite a lot of fixes have come in since the merge window, there's some repetitive fixes over the Qualcomm drivers increasing the patch count, along with a large batch of fixes from Cirrus. We also have some quirks and some individual fixes.
2024-08-09Merge tag 'drm-intel-fixes-2024-08-08' of ↵Dave Airlie
https://gitlab.freedesktop.org/drm/i915/kernel into drm-fixes - correct dual pps handling for MTL_PCH+ [display] (Dnyaneshwar Bhadane) - Adjust vma offset for framebuffer mmap offset [gem] (Andi Shyti) - Fix Virtual Memory mapping boundaries calculation [gem] (Andi Shyti) - Allow evicting to use the requested placement (David Gow) - Attempt to get pages without eviction first (David Gow) Signed-off-by: Dave Airlie <airlied@redhat.com> From: Tvrtko Ursulin <tursulin@igalia.com> Link: https://patchwork.freedesktop.org/patch/msgid/ZrSFpj20b1LbBhCJ@linux
2024-08-09Merge tag 'drm-xe-fixes-2024-08-08' of ↵Dave Airlie
https://gitlab.freedesktop.org/drm/xe/kernel into drm-fixes - Fix off-by-one when processing RTP rules (Lucas) - Use dma_fence_chain_free in chain fence unused as a sync (Brost) - Fix PL1 disable flow in xe_hwmon_power_max_write (Karthik) - Take ref to VM in delayed dump snapshot (Brost) Signed-off-by: Dave Airlie <airlied@redhat.com> From: Rodrigo Vivi <rodrigo.vivi@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/ZrUGgVrgTJ_vF2PS@intel.com
2024-08-08ksmbd: override fsids for smb2_query_info()Namjae Jeon
Sangsoo reported that a DAC denial error occurred when accessing files through the ksmbd thread. This patch override fsids for smb2_query_info(). Reported-by: Sangsoo Lee <constant.lee@samsung.com> Signed-off-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com>
2024-08-08ksmbd: override fsids for share path checkNamjae Jeon
Sangsoo reported that a DAC denial error occurred when accessing files through the ksmbd thread. This patch override fsids for share path check. Reported-by: Sangsoo Lee <constant.lee@samsung.com> Signed-off-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com>
2024-08-09Merge tag 'amd-drm-fixes-6.11-2024-08-08' of ↵Dave Airlie
https://gitlab.freedesktop.org/agd5f/linux into drm-fixes amd-drm-fixes-6.11-2024-08-08: amdgpu: - DMCUB fix - Fix DET programming on some DCNs - DCC fixes - DCN 4.0.1 fixes - SMU 14.0.x update - MMHUB fix - DCN 3.1.4 fix - GC 12.0 fixes - Fix soft recovery error propogation - SDMA 7.0 fixes - DSC fix drm buddy: - Add start address to trim function Signed-off-by: Dave Airlie <airlied@redhat.com> From: Alex Deucher <alexander.deucher@amd.com> Link: https://patchwork.freedesktop.org/patch/msgid/20240808161134.1227671-1-alexander.deucher@amd.com
2024-08-09Merge tag 'drm-misc-fixes-2024-08-08' of ↵Dave Airlie
https://gitlab.freedesktop.org/drm/misc/kernel into drm-fixes A fix for drm/client to prevent a null pointer dereference, a fix for a double-free in drm/bridge-connector, a fix for a gem shmem test, and a fix for async flips updates. Signed-off-by: Dave Airlie <airlied@redhat.com> From: Maxime Ripard <mripard@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20240808-debonair-smoky-mustang-8b6b3f@houat
2024-08-08cifs: cifs_inval_name_dfs_link_error: correct the check for fullpathGleb Korobeynikov
Replace the always-true check tcon->origin_fullpath with check of server->leaf_fullpath See https://bugzilla.kernel.org/show_bug.cgi?id=219083 The check of the new @tcon will always be true during mounting, since @tcon->origin_fullpath will only be set after the tree is connected to the latest common resource, as well as checking if the prefix paths from it are fully accessible. Fixes: 3ae872de4107 ("smb: client: fix shared DFS root mounts with different prefixes") Reviewed-by: Paulo Alcantara (Red Hat) <pc@manguebit.com> Signed-off-by: Gleb Korobeynikov <gkorobeynikov@astralinux.ru> Signed-off-by: Steve French <stfrench@microsoft.com>
2024-08-08Merge tag 'net-6.11-rc3' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net Pull networking fixes from Jakub Kicinski: "Including fixes from bluetooth. Current release - regressions: - eth: bnxt_en: fix memory out-of-bounds in bnxt_fill_hw_rss_tbl() on older chips Current release - new code bugs: - ethtool: fix off-by-one error / kdoc contradicting the code for max RSS context IDs - Bluetooth: hci_qca: - QCA6390: fix support on non-DT platforms - QCA6390: don't call pwrseq_power_off() twice - fix a NULL-pointer derefence at shutdown - eth: ice: fix incorrect assigns of FEC counters Previous releases - regressions: - mptcp: fix handling endpoints with both 'signal' and 'subflow' flags set - virtio-net: fix changing ring count when vq IRQ coalescing not supported - eth: gve: fix use of netif_carrier_ok() during reconfig / reset Previous releases - always broken: - eth: idpf: fix bugs in queue re-allocation on reconfig / reset - ethtool: fix context creation with no parameters Misc: - linkwatch: use system_unbound_wq to ease RTNL contention" * tag 'net-6.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (41 commits) net: dsa: microchip: disable EEE for KSZ8567/KSZ9567/KSZ9896/KSZ9897. ethtool: Fix context creation with no parameters net: ethtool: fix off-by-one error in max RSS context IDs net: pse-pd: tps23881: include missing bitfield.h header net: fec: Stop PPS on driver remove net: bcmgenet: Properly overlay PHY and MAC Wake-on-LAN capabilities l2tp: fix lockdep splat net: stmmac: dwmac4: fix PCS duplex mode decode idpf: fix UAFs when destroying the queues idpf: fix memleak in vport interrupt configuration idpf: fix memory leaks and crashes while performing a soft reset bnxt_en : Fix memory out-of-bounds in bnxt_fill_hw_rss_tbl() net: dsa: bcm_sf2: Fix a possible memory leak in bcm_sf2_mdio_register() net/smc: add the max value of fallback reason count Bluetooth: hci_sync: avoid dup filtering when passive scanning with adv monitor Bluetooth: l2cap: always unlock channel in l2cap_conless_channel() Bluetooth: hci_qca: fix a NULL-pointer derefence at shutdown Bluetooth: hci_qca: fix QCA6390 support on non-DT platforms Bluetooth: hci_qca: don't call pwrseq_power_off() twice for QCA6390 ice: Fix incorrect assigns of FEC counts ...
2024-08-08Merge tag 'trace-v6.11-rc2' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace Pull tracing fixes from Steven Rostedt: - Have reading of event format files test if the metadata still exists. When a event is freed, a flag (EVENT_FILE_FL_FREED) in the metadata is set to state that it is to prevent any new references to it from happening while waiting for existing references to close. When the last reference closes, the metadata is freed. But the "format" was missing a check to this flag (along with some other files) that allowed new references to happen, and a use-after-free bug to occur. - Have the trace event meta data use the refcount infrastructure instead of relying on its own atomic counters. - Have tracefs inodes use alloc_inode_sb() for allocation instead of using kmem_cache_alloc() directly. - Have eventfs_create_dir() return an ERR_PTR instead of NULL as the callers expect a real object or an ERR_PTR. - Have release_ei() use call_srcu() and not call_rcu() as all the protection is on SRCU and not RCU. - Fix ftrace_graph_ret_addr() to use the task passed in and not current. - Fix overflow bug in get_free_elt() where the counter can overflow the integer and cause an infinite loop. - Remove unused function ring_buffer_nr_pages() - Have tracefs freeing use the inode RCU infrastructure instead of creating its own. When the kernel had randomize structure fields enabled, the rcu field of the tracefs_inode was overlapping the rcu field of the inode structure, and corrupting it. Instead, use the destroy_inode() callback to do the initial cleanup of the code, and then have free_inode() free it. * tag 'trace-v6.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace: tracefs: Use generic inode RCU for synchronizing freeing ring-buffer: Remove unused function ring_buffer_nr_pages() tracing: Fix overflow in get_free_elt() function_graph: Fix the ret_stack used by ftrace_graph_ret_addr() eventfs: Use SRCU for freeing eventfs_inodes eventfs: Don't return NULL in eventfs_create_dir() tracefs: Fix inode allocation tracing: Use refcount for trace_event_file reference counter tracing: Have format file honor EVENT_FILE_FL_FREED
2024-08-08Merge tag 'bcachefs-2024-08-08' of git://evilpiepirate.org/bcachefsLinus Torvalds
Pull bcachefs fixes from Kent Overstreet: "Assorted little stuff: - lockdep fixup for lockdep_set_notrack_class() - we can now remove a device when using erasure coding without deadlocking, though we still hit other issues - the 'allocator stuck' timeout is now configurable, and messages are ratelimited. The default timeout has been increased from 10 seconds to 30" * tag 'bcachefs-2024-08-08' of git://evilpiepirate.org/bcachefs: bcachefs: Use bch2_wait_on_allocator() in btree node alloc path bcachefs: Make allocator stuck timeout configurable, ratelimit messages bcachefs: Add missing path_traverse() to btree_iter_next_node() bcachefs: ec should not allocate from ro devs bcachefs: Improved allocator debugging for ec bcachefs: Add missing bch2_trans_begin() call bcachefs: Add a comment for bucket helper types bcachefs: Don't rely on implicit unsigned -> signed integer conversion lockdep: Fix lockdep_set_notrack_class() for CONFIG_LOCK_STAT bcachefs: Fix double free of ca->buckets_nouse
2024-08-08selinux: revert our use of vma_is_initial_heap()Paul Moore
Unfortunately it appears that vma_is_initial_heap() is currently broken for applications that do not currently have any heap allocated, e.g. brk == start_brk. The breakage is such that it will cause SELinux to check for the process/execheap permission on memory regions that cross brk/start_brk even when there is no heap. The proper fix would be to correct vma_is_initial_heap(), but as there are multiple callers I am hesitant to unilaterally modify the helper out of concern that I would end up breaking some other subsystem. The mm developers have been made aware of the situation and hopefully they will have a fix at some point in the future, but we need a fix soon so we are simply going to revert our use of vma_is_initial_heap() in favor of our old logic/code which works as expected, even in the face of a zero size heap. We can return to using vma_is_initial_heap() at some point in the future when it is fixed. Cc: stable@vger.kernel.org Reported-by: Marc Reisner <reisner.marc@gmail.com> Closes: https://lore.kernel.org/all/ZrPmoLKJEf1wiFmM@marcreisner.com Fixes: 68df1baf158f ("selinux: use vma_is_initial_stack() and vma_is_initial_heap()") Signed-off-by: Paul Moore <paul@paul-moore.com>
2024-08-08media: Revert "media: dvb-usb: Fix unexpected infinite loop in ↵Sean Young
dvb_usb_read_remote_control()" This reverts commit 2052138b7da52ad5ccaf74f736d00f39a1c9198c. This breaks the TeVii s480 dual DVB-S2 S660. The device has a bulk in endpoint but no corresponding out endpoint, so the device does not pass the "has both receive and send bulk endpoint" test. Seemingly this device does not use dvb_usb_generic_rw() so I have tried removing the generic_bulk_ctrl_endpoint entry, but this resulted in different problems. As we have no explanation yet, revert. $ dmesg | grep -i -e dvb -e dw21 -e usb\ 4 [ 0.999122] usb 1-1: new high-speed USB device number 2 using ehci-pci [ 1.023123] usb 4-1: new high-speed USB device number 2 using ehci-pci [ 1.130247] usb 1-1: New USB device found, idVendor=9022, idProduct=d482, +bcdDevice= 0.01 [ 1.130257] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 1.152323] usb 4-1: New USB device found, idVendor=9022, idProduct=d481, +bcdDevice= 0.01 [ 1.152329] usb 4-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 6.701033] dvb-usb: found a 'TeVii S480.2 USB' in cold state, will try to +load a firmware [ 6.701178] dvb-usb: downloading firmware from file 'dvb-usb-s660.fw' [ 6.701179] dw2102: start downloading DW210X firmware [ 6.703715] dvb-usb: found a 'Microsoft Xbox One Digital TV Tuner' in cold +state, will try to load a firmware [ 6.703974] dvb-usb: downloading firmware from file 'dvb-usb-dib0700-1.20.fw' [ 6.756432] usb 1-1: USB disconnect, device number 2 [ 6.862119] dvb-usb: found a 'TeVii S480.2 USB' in warm state. [ 6.862194] dvb-usb: TeVii S480.2 USB error while loading driver (-22) [ 6.862209] dvb-usb: found a 'TeVii S480.1 USB' in cold state, will try to +load a firmware [ 6.862244] dvb-usb: downloading firmware from file 'dvb-usb-s660.fw' [ 6.862245] dw2102: start downloading DW210X firmware [ 6.914811] usb 4-1: USB disconnect, device number 2 [ 7.014131] dvb-usb: found a 'TeVii S480.1 USB' in warm state. [ 7.014487] dvb-usb: TeVii S480.1 USB error while loading driver (-22) [ 7.014538] usbcore: registered new interface driver dw2102 Closes: https://lore.kernel.org/stable/20240801165146.38991f60@mir/ Fixes: 2052138b7da5 ("media: dvb-usb: Fix unexpected infinite loop in dvb_usb_read_remote_control()") Reported-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> Cc: stable@vger.kernel.org Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2024-08-08ASoC: cs35l56: Patch CS35L56_IRQ1_MASK_18 to the default valueSimon Trimmer
Device tuning files made with early revision tooling may contain configuration that can unmask IRQ signals that are owned by the host. Adding a safe default to the regmap patch ensures that the hardware matches the driver expectations. Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com> Link: https://patch.msgid.link/20240807142648.46932-1-simont@opensource.cirrus.com Signed-off-by: Mark Brown <broonie@kernel.org>
2024-08-08ASoC: meson: axg-fifo: fix irq scheduling issue with PREEMPT_RTJerome Brunet
With PREEMPT_RT enabled a spinlock_t becomes a sleeping lock. This is usually not a problem with spinlocks used in IRQ context since IRQ handlers get threaded. However, if IRQF_ONESHOT is set, the primary handler won't be force-threaded and runs always in hardirq context. This is a problem because spinlock_t requires a preemptible context on PREEMPT_RT. In this particular instance, regmap mmio uses spinlock_t to protect the register access and IRQF_ONESHOT is set on the IRQ. In this case, it is actually better to do everything in threaded handler and it solves the problem with PREEMPT_RT. Reported-by: Arseniy Krasnov <avkrasnov@salutedevices.com> Closes: https://lore.kernel.org/linux-amlogic/20240729131652.3012327-1-avkrasnov@salutedevices.com Suggested-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Fixes: b11d26660dff ("ASoC: meson: axg-fifo: use threaded irq to check periods") Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Link: https://patch.msgid.link/20240807162705.4024136-1-jbrunet@baylibre.com Signed-off-by: Mark Brown <broonie@kernel.org>
generated by cgit (git 2.34.1) at 2025-09-14 21:32:38 +0000