| Age | Commit message (Collapse) | Author |
|---|
|
In 2020, there's been an unnoticed change which rightfully attempted to
report probe deferrals upon DMA absence by checking the return value of
dma_request_chan_by_mask(). By doing so, it also reported errors which
were simply ignored otherwise, likely on purpose.
This change actually turned a void return into an error code. Hence, not
only the -EPROBE_DEFER error codes but all error codes got reported to
the callers, now failing to probe in the absence of Rx DMA channel,
despite the fact that DMA seems to not be supported natively by many
implementations.
Looking at the history, this change probably led to:
ad2775dc3fc5 ("spi: cadence-quadspi: Disable the DAC for Intel LGM SoC")
f724c296f2f2 ("spi: cadence-quadspi: fix Direct Access Mode disable for SoCFPGA")
In my case, the AM62A LP SK core octo-SPI node from TI does not
advertise any DMA channel, hinting that there is likely no support for
it, but yet when the support for the am654 compatible was added, DMA
seemed to be used, so just discarding its use with the
CQSPI_DISABLE_DAC_MODE quirk for this compatible does not seem the
correct approach.
Let's get change the return condition back to:
- return a probe deferral error if we get one
- ignore the return value otherwise
The "error" log level was however likely too high for something that is
expected to fail, so let's lower it arbitrarily to the info level.
Fixes: 935da5e5100f ("mtd: spi-nor: cadence-quadspi: Handle probe deferral while requesting DMA channel")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://patch.msgid.link/20250305200933.2512925-2-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
atapi_check_dma() allows a LLD to filter ATAPI commands, returning a
status indicating whether or not it is OK to use DMA for the supplied
ATAPI command.
Change atapi_check_dma() to return -EOPNOTSUPP instead of 1 for an
ATAPI command that is not allowed to use DMA.
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Link: https://lore.kernel.org/r/20250312133954.6666-1-chenhuacai@loongson.cn
[cassel: improve commit log]
Signed-off-by: Niklas Cassel <cassel@kernel.org>
|
|
Add a fixup to enable the mute LED on HP Pavilion x360 Convertible
14-dy1xxx with ALC295 codec. The appropriate coefficient index and bits
were identified through a brute-force method, as detailed in
https://bbs.archlinux.org/viewtopic.php?pid=2079504#p2079504.
Signed-off-by: Navon John Lukose <navonjohnlukose@gmail.com>
Link: https://patch.msgid.link/20250307213319.35507-1-navonjohnlukose@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The get->num_services variable is an unsigned int which is controlled by
the user. The struct_size() function ensures that the size calculation
does not overflow an unsigned long, however, we are saving the result to
an int so the calculation can overflow.
Both "len" and "get->num_services" come from the user. This check is
just a sanity check to help the user and ensure they are using the API
correctly. An integer overflow here is not a big deal. This has no
security impact.
Save the result from struct_size() type size_t to fix this integer
overflow bug.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
We are trying to get rid of all multiplications from allocation
functions to prevent potential integer overflows. Here the
multiplication is probably safe, but using kcalloc() is more
appropriate and improves readability. This patch has no effect
on runtime behavior.
Link: https://github.com/KSPP/linux/issues/162 [1]
Link: https://www.kernel.org/doc/html/next/process/deprecated.html#open-coded-arithmetic-in-allocator-arguments
Signed-off-by: Ethan Carter Edwards <ethan@ethancedwards.com>
Link: https://patch.msgid.link/20250308-ctdaio-kzalloc-v1-1-804a09875b0e@ethancedwards.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
These scripts fail if the kernel is tainted which leads to wrong test
failure reports in CI environments when an unrelated test triggers some
splat.
Check taint state at start of script and SKIP if its already dodgy.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
insert_tree()
Since commit b36e4523d4d5 ("netfilter: nf_conncount: fix garbage
collection confirm race"), `cpu` and `jiffies32` were introduced to
the struct nf_conncount_tuple.
The commit made nf_conncount_add() initialize `conn->cpu` and
`conn->jiffies32` when allocating the struct.
In contrast, count_tree() was not changed to initialize them.
By commit 34848d5c896e ("netfilter: nf_conncount: Split insert and
traversal"), count_tree() was split and the relevant allocation
code now resides in insert_tree().
Initialize `conn->cpu` and `conn->jiffies32` in insert_tree().
BUG: KMSAN: uninit-value in find_or_evict net/netfilter/nf_conncount.c:117 [inline]
BUG: KMSAN: uninit-value in __nf_conncount_add+0xd9c/0x2850 net/netfilter/nf_conncount.c:143
find_or_evict net/netfilter/nf_conncount.c:117 [inline]
__nf_conncount_add+0xd9c/0x2850 net/netfilter/nf_conncount.c:143
count_tree net/netfilter/nf_conncount.c:438 [inline]
nf_conncount_count+0x82f/0x1e80 net/netfilter/nf_conncount.c:521
connlimit_mt+0x7f6/0xbd0 net/netfilter/xt_connlimit.c:72
__nft_match_eval net/netfilter/nft_compat.c:403 [inline]
nft_match_eval+0x1a5/0x300 net/netfilter/nft_compat.c:433
expr_call_ops_eval net/netfilter/nf_tables_core.c:240 [inline]
nft_do_chain+0x426/0x2290 net/netfilter/nf_tables_core.c:288
nft_do_chain_ipv4+0x1a5/0x230 net/netfilter/nft_chain_filter.c:23
nf_hook_entry_hookfn include/linux/netfilter.h:154 [inline]
nf_hook_slow+0xf4/0x400 net/netfilter/core.c:626
nf_hook_slow_list+0x24d/0x860 net/netfilter/core.c:663
NF_HOOK_LIST include/linux/netfilter.h:350 [inline]
ip_sublist_rcv+0x17b7/0x17f0 net/ipv4/ip_input.c:633
ip_list_rcv+0x9ef/0xa40 net/ipv4/ip_input.c:669
__netif_receive_skb_list_ptype net/core/dev.c:5936 [inline]
__netif_receive_skb_list_core+0x15c5/0x1670 net/core/dev.c:5983
__netif_receive_skb_list net/core/dev.c:6035 [inline]
netif_receive_skb_list_internal+0x1085/0x1700 net/core/dev.c:6126
netif_receive_skb_list+0x5a/0x460 net/core/dev.c:6178
xdp_recv_frames net/bpf/test_run.c:280 [inline]
xdp_test_run_batch net/bpf/test_run.c:361 [inline]
bpf_test_run_xdp_live+0x2e86/0x3480 net/bpf/test_run.c:390
bpf_prog_test_run_xdp+0xf1d/0x1ae0 net/bpf/test_run.c:1316
bpf_prog_test_run+0x5e5/0xa30 kernel/bpf/syscall.c:4407
__sys_bpf+0x6aa/0xd90 kernel/bpf/syscall.c:5813
__do_sys_bpf kernel/bpf/syscall.c:5902 [inline]
__se_sys_bpf kernel/bpf/syscall.c:5900 [inline]
__ia32_sys_bpf+0xa0/0xe0 kernel/bpf/syscall.c:5900
ia32_sys_call+0x394d/0x4180 arch/x86/include/generated/asm/syscalls_32.h:358
do_syscall_32_irqs_on arch/x86/entry/common.c:165 [inline]
__do_fast_syscall_32+0xb0/0x110 arch/x86/entry/common.c:387
do_fast_syscall_32+0x38/0x80 arch/x86/entry/common.c:412
do_SYSENTER_32+0x1f/0x30 arch/x86/entry/common.c:450
entry_SYSENTER_compat_after_hwframe+0x84/0x8e
Uninit was created at:
slab_post_alloc_hook mm/slub.c:4121 [inline]
slab_alloc_node mm/slub.c:4164 [inline]
kmem_cache_alloc_noprof+0x915/0xe10 mm/slub.c:4171
insert_tree net/netfilter/nf_conncount.c:372 [inline]
count_tree net/netfilter/nf_conncount.c:450 [inline]
nf_conncount_count+0x1415/0x1e80 net/netfilter/nf_conncount.c:521
connlimit_mt+0x7f6/0xbd0 net/netfilter/xt_connlimit.c:72
__nft_match_eval net/netfilter/nft_compat.c:403 [inline]
nft_match_eval+0x1a5/0x300 net/netfilter/nft_compat.c:433
expr_call_ops_eval net/netfilter/nf_tables_core.c:240 [inline]
nft_do_chain+0x426/0x2290 net/netfilter/nf_tables_core.c:288
nft_do_chain_ipv4+0x1a5/0x230 net/netfilter/nft_chain_filter.c:23
nf_hook_entry_hookfn include/linux/netfilter.h:154 [inline]
nf_hook_slow+0xf4/0x400 net/netfilter/core.c:626
nf_hook_slow_list+0x24d/0x860 net/netfilter/core.c:663
NF_HOOK_LIST include/linux/netfilter.h:350 [inline]
ip_sublist_rcv+0x17b7/0x17f0 net/ipv4/ip_input.c:633
ip_list_rcv+0x9ef/0xa40 net/ipv4/ip_input.c:669
__netif_receive_skb_list_ptype net/core/dev.c:5936 [inline]
__netif_receive_skb_list_core+0x15c5/0x1670 net/core/dev.c:5983
__netif_receive_skb_list net/core/dev.c:6035 [inline]
netif_receive_skb_list_internal+0x1085/0x1700 net/core/dev.c:6126
netif_receive_skb_list+0x5a/0x460 net/core/dev.c:6178
xdp_recv_frames net/bpf/test_run.c:280 [inline]
xdp_test_run_batch net/bpf/test_run.c:361 [inline]
bpf_test_run_xdp_live+0x2e86/0x3480 net/bpf/test_run.c:390
bpf_prog_test_run_xdp+0xf1d/0x1ae0 net/bpf/test_run.c:1316
bpf_prog_test_run+0x5e5/0xa30 kernel/bpf/syscall.c:4407
__sys_bpf+0x6aa/0xd90 kernel/bpf/syscall.c:5813
__do_sys_bpf kernel/bpf/syscall.c:5902 [inline]
__se_sys_bpf kernel/bpf/syscall.c:5900 [inline]
__ia32_sys_bpf+0xa0/0xe0 kernel/bpf/syscall.c:5900
ia32_sys_call+0x394d/0x4180 arch/x86/include/generated/asm/syscalls_32.h:358
do_syscall_32_irqs_on arch/x86/entry/common.c:165 [inline]
__do_fast_syscall_32+0xb0/0x110 arch/x86/entry/common.c:387
do_fast_syscall_32+0x38/0x80 arch/x86/entry/common.c:412
do_SYSENTER_32+0x1f/0x30 arch/x86/entry/common.c:450
entry_SYSENTER_compat_after_hwframe+0x84/0x8e
Reported-by: syzbot+83fed965338b573115f7@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=83fed965338b573115f7
Fixes: b36e4523d4d5 ("netfilter: nf_conncount: fix garbage collection confirm race")
Signed-off-by: Kohei Enju <enjuk@amazon.com>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Commit 1f47ed294a2b ("block: cleanup and fix batch completion adding
conditions") modified the evaluation criteria for the third argument,
'ioerror', in the blk_mq_add_to_batch() function. Initially, the
function had checked if 'ioerror' equals zero. Following the commit, it
started checking for negative error values, with the presumption that
such values, for instance -EIO, would be passed in.
However, blk_mq_add_to_batch() callers do not pass negative error
values. Instead, they pass status codes defined in various ways:
- NVMe PCI and Apple drivers pass NVMe status code
- virtio_blk driver passes the virtblk request header status byte
- null_blk driver passes blk_status_t
These codes are either zero or positive, therefore the revised check
fails to function as intended. Specifically, with the NVMe PCI driver,
this modification led to the failure of the blktests test case nvme/039.
In this test scenario, errors are artificially injected to the NVMe
driver, resulting in positive NVMe status codes passed to
blk_mq_add_to_batch(), which unexpectedly processes the failed I/O in a
batch. Hence the failure.
To correct the ioerror check within blk_mq_add_to_batch(), make all
callers to uniformly pass the argument as boolean. Modify the callers to
check their specific status codes and pass the boolean value 'is_error'.
Also describe the arguments of blK_mq_add_to_batch as kerneldoc.
Fixes: 1f47ed294a2b ("block: cleanup and fix batch completion adding conditions")
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Link: https://lore.kernel.org/r/20250311104359.1767728-3-shinichiro.kawasaki@wdc.com
[axboe: fold in documentation update]
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The blk_mq_map_queue()'s request_queue param is not used anymore,
remove it, same with blk_get_flush_queue().
Signed-off-by: Guixin Liu <kanie@linux.alibaba.com>
Link: https://lore.kernel.org/r/20250312084722.129680-1-kanie@linux.alibaba.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless
Johannes berg says:
====================
Few more fixes:
- cfg80211/mac80211
- stop possible runaway wiphy worker
- EHT should not use reserved MPDU size bits
- don't run worker for stopped interfaces
- fix SA Query processing with MLO
- fix lookup of assoc link BSS entries
- correct station flush on unauthorize
- iwlwifi:
- TSO fixes
- fix non-MSI-X platforms
- stop possible runaway restart worker
- rejigger maintainers so I'm not CC'ed on
everything
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Driver is always clearing the mask that sets the VLAN ID/Service Level
in the adapter. Recent change for supporting multiple traffic class
exposed this issue.
Allow setting SL and VLAN_ID while QP is moved from INIT to RTR state.
Fixes: 1ac5a4047975 ("RDMA/bnxt_re: Add bnxt_re RoCE driver")
Fixes: c64b16a37b6d ("RDMA/bnxt_re: Support different traffic class")
Signed-off-by: Saravanan Vajravel <saravanan.vajravel@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/1741670196-2919-1-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
As discussed in [1], if 'bdr' is set once, it would never get
cleared, hence 0 is always returned.
Refactor the range check hunk into a new helper dma_find_range(),
which allows 'bdr' to be cleared in each iteration.
Link: https://lore.kernel.org/all/64931fac-085b-4ff3-9314-84bac2fa9bdb@quicinc.com/ # [1]
Fixes: a409d9600959 ("dma-mapping: fix dma_addressing_limited() if dma_range_map can't cover all system RAM")
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://lore.kernel.org/r/20250307030350.69144-1-quic_bqiang@quicinc.com
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
|
|
We create a gpio descriptor table but it needs to be free:ed
when the module is removed. Add a devm_ action to do the job.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Fixes: da9146c19b17 ("ASoC: samsung: speyside: Convert to GPIO descriptor")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20250312-cleanup-table-v1-1-1d9a14464482@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Drop all PXD_TABLE_BIT macros as they are not used any more.
Cc: Will Deacon <will@kernel.org>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Ryan Roberts <ryan.roberts@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Link: https://lore.kernel.org/r/20250221044227.1145393-9-anshuman.khandual@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Check for pmd_table() in pmd_trans_huge() rather then just checking for the
PMD_TABLE_BIT. But ensure all present-invalid entries are handled correctly
by always setting PTE_VALID before checking with pmd_table().
Cc: Will Deacon <will@kernel.org>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Ryan Roberts <ryan.roberts@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ryan Roberts <ryan.roberts@arm.com>
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Link: https://lore.kernel.org/r/20250221044227.1145393-8-anshuman.khandual@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
pud_bad() is currently defined in terms of pud_table(). Although for some
configs, pud_table() is hard-coded to true i.e. when using 64K base pages
or when page table levels are less than 3.
pud_bad() is intended to check that the pud is configured correctly. Hence
let's open-code the same check that the full version of pud_table() uses
into pud_bad(). Then it always performs the check regardless of the config.
Cc: Will Deacon <will@kernel.org>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Ryan Roberts <ryan.roberts@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ryan Roberts <ryan.roberts@arm.com>
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Link: https://lore.kernel.org/r/20250221044227.1145393-7-anshuman.khandual@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Check page table entries against PXD_TYPE_TABLE on PXD_TYPE_MASK mask bits
in [p4d|pgd]_bad() while determining a table entry instead of just checking
only for PXD_TABLE_BIT.
Cc: Will Deacon <will@kernel.org>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Ryan Roberts <ryan.roberts@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Link: https://lore.kernel.org/r/20250221044227.1145393-6-anshuman.khandual@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Clear PXX_TYPE_MASK in [pmd|pud]_mkhuge() while creating section mappings
instead of just the PXX_TABLE_BIT and also set PXD_TYPE_SECT. Also ensure
PTE_VALID does not get modified in these helpers, because present-invalid
entries should preserve their state across.
Cc: Will Deacon <will@kernel.org>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Ryan Roberts <ryan.roberts@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Link: https://lore.kernel.org/r/20250221044227.1145393-5-anshuman.khandual@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Clear PXX_TYPE_MASK bits in mk_[pmd|pud]_sect_prot() while creating section
mappings instead of just clearing the PXX_TABLE_BIT.
Cc: Will Deacon <will@kernel.org>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Ryan Roberts <ryan.roberts@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Link: https://lore.kernel.org/r/20250221044227.1145393-4-anshuman.khandual@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Test given page table entries against PMD_TYPE_SECT on PMD_TYPE_MASK mask
bits for identifying block mappings in stage 1 page tables.
Cc: Will Deacon <will@kernel.org>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Ryan Roberts <ryan.roberts@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Link: https://lore.kernel.org/r/20250221044227.1145393-3-anshuman.khandual@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Test given page table entries against PMD_TYPE_SECT on PMD_TYPE_MASK mask
bits for identifying block mappings in stage 2 page tables.
Cc: Marc Zyngier <maz@kernel.org>
Cc: Oliver Upton <oliver.upton@linux.dev>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: kvmarm@lists.linux.dev
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Ryan Roberts <ryan.roberts@arm.com>
Link: https://lore.kernel.org/r/20250221044227.1145393-2-anshuman.khandual@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Adding the aligned(1024) attribute to the definition of __rseq_abi did
not increase its size to 1024, for this attribute to impact the size of
__rseq_abi it would need to be added to the declaration of 'struct
rseq_abi'. We only want to increase the size of the TLS allocation to
ensure registration will succeed with future extended ABI. Use a union
with a dummy member to ensure we allocate 1024 bytes.
Signed-off-by: Michael Jeanson <mjeanson@efficios.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Link: https://lore.kernel.org/r/20250311192222.323453-1-mjeanson@efficios.com
|
|
Even though no uses of the bzImage CRC-32 checksum are known, ensure
that the last 4 bytes of the image are unused zero bytes, so that the
checksum can be generated post-build if needed.
[ mingo: Added the 'obsolete' qualifier to the comment. ]
Suggested-by: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://lore.kernel.org/r/20250312081204.521411-2-ardb+git@google.com
|
|
Each of get_{mon,ctrl}_domain_from_cpu() only has one caller.
Once the filesystem code is moved to /fs/, there is no equivalent to
core.c.
Move these functions to each live next to their caller. This allows
them to be made static and the header file entries to be removed.
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Fenghua Yu <fenghuay@nvidia.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Babu Moger <babu.moger@amd.com>
Reviewed-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Tested-by: Peter Newman <peternewman@google.com>
Tested-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Tested-by: Amit Singh Tomar <amitsinght@marvell.com> # arm64
Tested-by: Shanker Donthineni <sdonthineni@nvidia.com> # arm64
Tested-by: Babu Moger <babu.moger@amd.com>
Link: https://lore.kernel.org/r/20250311183715.16445-31-james.morse@arm.com
|
|
get_config_index() is used by the architecture specific code to map
a CLOSID+type pair to an index in the configuration arrays.
MPAM needs to do this too to preserve the ABI to user-space, there is no
reason to do it differently.
Move the helper to a header file to allow all architectures that either
use or emulate CDP to use the same pattern of CLOSID values. Moving
this to a header file means it must be marked inline, which matches
the existing compiler choice for this static function.
Co-developed-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Fenghua Yu <fenghuay@nvidia.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Babu Moger <babu.moger@amd.com>
Tested-by: Carl Worth <carl@os.amperecomputing.com> # arm64
Tested-by: Shanker Donthineni <sdonthineni@nvidia.com> # arm64
Tested-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Tested-by: Peter Newman <peternewman@google.com>
Tested-by: Amit Singh Tomar <amitsinght@marvell.com> # arm64
Tested-by: Babu Moger <babu.moger@amd.com>
Link: https://lore.kernel.org/r/20250311183715.16445-30-james.morse@arm.com
|
|
If i2c_add_adapter() fails, the request_region() call in sis630_setup()
must be undone by a corresponding release_region() call, as done in the
remove function.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/3d607601f2c38e896b10207963c6ab499ca5c307.1741033587.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
If i2c_add_adapter() fails, the request_region() call in ali15x3_setup()
must be undone by a corresponding release_region() call, as done in the
remove function.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/9b2090cbcc02659f425188ea05f2e02745c4e67b.1741031878.git.christophe.jaillet@wanadoo.fr
|
|
If i2c_add_adapter() fails, the request_region() call in ali1535_setup()
must be undone by a corresponding release_region() call, as done in the
remove function.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/0daf63d7a2ce74c02e2664ba805bbfadab7d25e5.1741031571.git.christophe.jaillet@wanadoo.fr
|
|
Now that the visibility of throttle_mode is being managed by resctrl, it
should consider resources other than MBA that may have a throttle_mode. SMBA
is one such resource.
Extend thread_throttle_mode_init() to check SMBA for a throttle_mode.
Adding support for multiple resources means it is possible for a platform with
both MBA and SMBA, but an undefined throttle_mode on one of them to make the
file visible.
Add the 'undefined' case to rdt_thread_throttle_mode_show().
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Fenghua Yu <fenghuay@nvidia.com>
Reviewed-by: Babu Moger <babu.moger@amd.com>
Reviewed-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Tested-by: Peter Newman <peternewman@google.com>
Tested-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Tested-by: Amit Singh Tomar <amitsinght@marvell.com> # arm64
Tested-by: Shanker Donthineni <sdonthineni@nvidia.com> # arm64
Tested-by: Babu Moger <babu.moger@amd.com>
Link: https://lore.kernel.org/r/20250311183715.16445-29-james.morse@arm.com
|
|
resctrl_file_fflags_init() is called from the architecture specific code to
make the 'thread_throttle_mode' file visible. The architecture specific code
has already set the membw.throttle_mode in the rdt_resource.
This forces the RFTYPE flags used by resctrl to be exposed to the architecture
specific code.
This doesn't need to be specific to the architecture, the throttle_mode can be
used by resctrl to determine if the 'thread_throttle_mode' file should be
visible. This allows the RFTYPE flags to be private to resctrl.
Add thread_throttle_mode_init(), and use it to call resctrl_file_fflags_init()
from resctrl_init(). This avoids publishing an extra function between the
architecture and filesystem code.
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Fenghua Yu <fenghuay@nvidia.com>
Reviewed-by: Babu Moger <babu.moger@amd.com>
Reviewed-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Tested-by: Peter Newman <peternewman@google.com>
Tested-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Tested-by: Amit Singh Tomar <amitsinght@marvell.com> # arm64
Tested-by: Shanker Donthineni <sdonthineni@nvidia.com> # arm64
Tested-by: Babu Moger <babu.moger@amd.com>
Link: https://lore.kernel.org/r/20250311183715.16445-28-james.morse@arm.com
|
|
On the GTA04A5 writing a reset command to the gyroscope causes IRQ
storms because NACK IRQs are enabled and therefore triggered but not
acked.
Sending a reset command to the gyroscope by
i2cset 1 0x69 0x14 0xb6
with an additional debug print in the ISR (not the thread) itself
causes
[ 363.353515] i2c i2c-1: ioctl, cmd=0x720, arg=0xbe801b00
[ 363.359039] omap_i2c 48072000.i2c: addr: 0x0069, len: 2, flags: 0x0, stop: 1
[ 363.366180] omap_i2c 48072000.i2c: IRQ LL (ISR = 0x1110)
[ 363.371673] omap_i2c 48072000.i2c: IRQ (ISR = 0x0010)
[ 363.376892] omap_i2c 48072000.i2c: IRQ LL (ISR = 0x0102)
[ 363.382263] omap_i2c 48072000.i2c: IRQ LL (ISR = 0x0102)
[ 363.387664] omap_i2c 48072000.i2c: IRQ LL (ISR = 0x0102)
repeating till infinity
[...]
(0x2 = NACK, 0x100 = Bus free, which is not enabled)
Apparently no other IRQ bit gets set, so this stalls.
Do not ignore enabled interrupts and make sure they are acked.
If the NACK IRQ is not needed, it should simply not enabled, but
according to the above log, caring about it is necessary unless
the Bus free IRQ is enabled and handled. The assumption that is
will always come with a ARDY IRQ, which was the idea behind
ignoring it, proves wrong.
It is true for simple reads from an unused address.
To still avoid the i2cdetect trouble which is the reason for
commit c770657bd261 ("i2c: omap: Fix standard mode false ACK readings"),
avoid doing much about NACK in omap_i2c_xfer_data() which is used
by both IRQ mode and polling mode, so also the false detection fix
is extended to polling usage and IRQ storms are avoided.
By changing this, the hardirq handler is not needed anymore to filter
stuff.
The mentioned gyro reset now just causes a -ETIMEDOUT instead of
hanging the system.
Fixes: c770657bd261 ("i2c: omap: Fix standard mode false ACK readings").
CC: stable@kernel.org
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Tested-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Aniket Limaye <a-limaye@ti.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250228140420.379498-1-andreas@kemnade.info
|
|
resctrl_arch_pseudo_lock_fn() has architecture specific behaviour,
and takes a struct rdtgroup as an argument.
After the filesystem code moves to /fs/, the definition of struct
rdtgroup will not be available to the architecture code.
The only reason resctrl_arch_pseudo_lock_fn() wants the rdtgroup is
for the CLOSID. Embed that in the pseudo_lock_region as a closid,
and move the definition of struct pseudo_lock_region to resctrl.h.
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Fenghua Yu <fenghuay@nvidia.com>
Reviewed-by: Babu Moger <babu.moger@amd.com>
Tested-by: Carl Worth <carl@os.amperecomputing.com> # arm64
Tested-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Tested-by: Peter Newman <peternewman@google.com>
Tested-by: Amit Singh Tomar <amitsinght@marvell.com> # arm64
Tested-by: Shanker Donthineni <sdonthineni@nvidia.com> # arm64
Tested-by: Babu Moger <babu.moger@amd.com>
Link: https://lore.kernel.org/r/20250311183715.16445-27-james.morse@arm.com
|
|
prefetch_disable_bits is set by rdtgroup_locksetup_enter() from a value
provided by the architecture, but is largely read by other architecture
helpers.
Make resctrl_arch_get_prefetch_disable_bits() set prefetch_disable_bits so
that it can be isolated to arch-code from where the other arch-code helpers
can use its cached value.
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Fenghua Yu <fenghuay@nvidia.com>
Reviewed-by: Babu Moger <babu.moger@amd.com>
Tested-by: Carl Worth <carl@os.amperecomputing.com> # arm64
Tested-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Tested-by: Peter Newman <peternewman@google.com>
Tested-by: Amit Singh Tomar <amitsinght@marvell.com> # arm64
Tested-by: Shanker Donthineni <sdonthineni@nvidia.com> # arm64
Tested-by: Babu Moger <babu.moger@amd.com>
Link: https://lore.kernel.org/r/20250311183715.16445-26-james.morse@arm.com
|
|
Pseudo-lock relies on knowledge of the micro-architecture to disable
prefetchers etc.
On arm64 these controls are typically secure only, meaning Linux can't access
them. Arm's cache-lockdown feature works in a very different way. Resctrl's
pseudo-lock isn't going to be used on arm64 platforms.
Add a Kconfig symbol that can be selected by the architecture. This enables or
disables building of the pseudo_lock.c file, and replaces the functions with
stubs. An additional IS_ENABLED() check is needed in rdtgroup_mode_write() so
that attempting to enable pseudo-lock reports an "Unknown or unsupported mode"
to user-space via the last_cmd_status file.
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Fenghua Yu <fenghuay@nvidia.com>
Reviewed-by: Babu Moger <babu.moger@amd.com>
Tested-by: Carl Worth <carl@os.amperecomputing.com> # arm64
Tested-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Tested-by: Peter Newman <peternewman@google.com>
Tested-by: Amit Singh Tomar <amitsinght@marvell.com> # arm64
Tested-by: Shanker Donthineni <sdonthineni@nvidia.com> # arm64
Tested-by: Babu Moger <babu.moger@amd.com>
Link: https://lore.kernel.org/r/20250311183715.16445-25-james.morse@arm.com
|
|
resctrl's pseudo lock has some copy-to-cache and measurement functions that
are micro-architecture specific.
For example, pseudo_lock_fn() is not at all portable.
Label these 'resctrl_arch_' so they stay under /arch/x86. To expose these
functions to the filesystem code they need an entry in a header file, and
can't be marked static.
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Fenghua Yu <fenghuay@nvidia.com>
Reviewed-by: Babu Moger <babu.moger@amd.com>
Tested-by: Carl Worth <carl@os.amperecomputing.com> # arm64
Tested-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Tested-by: Peter Newman <peternewman@google.com>
Tested-by: Amit Singh Tomar <amitsinght@marvell.com> # arm64
Tested-by: Shanker Donthineni <sdonthineni@nvidia.com> # arm64
Tested-by: Babu Moger <babu.moger@amd.com>
Link: https://lore.kernel.org/r/20250311183715.16445-24-james.morse@arm.com
|
|
The mbm_cfg_mask field lists the bits that user-space can set when configuring
an event. This value is output via the last_cmd_status file.
Once the filesystem parts of resctrl are moved to live in /fs/, the struct
rdt_hw_resource is inaccessible to the filesystem code. Because this value is
output to user-space, it has to be accessible to the filesystem code.
Move it to struct rdt_resource.
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Fenghua Yu <fenghuay@nvidia.com>
Reviewed-by: Babu Moger <babu.moger@amd.com>
Tested-by: Carl Worth <carl@os.amperecomputing.com> # arm64
Tested-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Tested-by: Peter Newman <peternewman@google.com>
Tested-by: Amit Singh Tomar <amitsinght@marvell.com> # arm64
Tested-by: Shanker Donthineni <sdonthineni@nvidia.com> # arm64
Tested-by: Babu Moger <babu.moger@amd.com>
Link: https://lore.kernel.org/r/20250311183715.16445-23-james.morse@arm.com
|
|
mba_mbps_default_event is initialised based on whether mbm_local or mbm_total
is supported. In the case of both, it is initialised to mbm_local.
mba_mbps_default_event is initialised in core.c's get_rdt_mon_resources(),
while all the readers are in rdtgroup.c.
After this code is split into architecture-specific and filesystem code,
get_rdt_mon_resources() remains part of the architecture code, which would
mean mba_mbps_default_event has to be exposed by the filesystem code.
Move the initialisation to the filesystem's resctrl_mon_resource_init().
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Fenghua Yu <fenghuay@nvidia.com>
Reviewed-by: Babu Moger <babu.moger@amd.com>
Reviewed-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Tested-by: Peter Newman <peternewman@google.com>
Tested-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Tested-by: Amit Singh Tomar <amitsinght@marvell.com> # arm64
Tested-by: Shanker Donthineni <sdonthineni@nvidia.com> # arm64
Tested-by: Babu Moger <babu.moger@amd.com>
Link: https://lore.kernel.org/r/20250311183715.16445-22-james.morse@arm.com
|
|
mon_event_config_{read,write}() are called via IPI and access model specific
registers to do their work.
To support another architecture, this needs abstracting.
Rename mon_event_config_{read,write}() to have a "resctrl_arch_" prefix, and
move their struct mon_config_info parameter into <linux/resctrl.h>. This
allows another architecture to supply an implementation of these.
As struct mon_config_info is now exposed globally, give it a 'resctrl_'
prefix. MPAM systems need access to the domain to do this work, add the
resource and domain to struct resctrl_mon_config_info.
Co-developed-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Fenghua Yu <fenghuay@nvidia.com>
Reviewed-by: Babu Moger <babu.moger@amd.com>
Tested-by: Carl Worth <carl@os.amperecomputing.com> # arm64
Tested-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Tested-by: Peter Newman <peternewman@google.com>
Tested-by: Amit Singh Tomar <amitsinght@marvell.com> # arm64
Tested-by: Shanker Donthineni <sdonthineni@nvidia.com> # arm64
Tested-by: Babu Moger <babu.moger@amd.com>
Link: https://lore.kernel.org/r/20250311183715.16445-21-james.morse@arm.com
|
|
When BMEC is supported the resctrl event can be configured in a number of
ways. This depends on architecture support. rdt_get_mon_l3_config() modifies
the struct mon_evt and calls resctrl_file_fflags_init() to create the files
that allow the configuration.
Splitting this into separate architecture and filesystem parts would require
the struct mon_evt and resctrl_file_fflags_init() to be exposed.
Instead, add resctrl_arch_is_evt_configurable(), and use this from
resctrl_mon_resource_init() to initialise struct mon_evt and call
resctrl_file_fflags_init().
resctrl_arch_is_evt_configurable() calls rdt_cpu_has() so it doesn't obviously
benefit from being inlined. Putting it in core.c will allow rdt_cpu_has() to
eventually become static.
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Fenghua Yu <fenghuay@nvidia.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Babu Moger <babu.moger@amd.com>
Tested-by: Carl Worth <carl@os.amperecomputing.com> # arm64
Tested-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Tested-by: Peter Newman <peternewman@google.com>
Tested-by: Amit Singh Tomar <amitsinght@marvell.com> # arm64
Tested-by: Shanker Donthineni <sdonthineni@nvidia.com> # arm64
Tested-by: Babu Moger <babu.moger@amd.com>
Link: https://lore.kernel.org/r/20250311183715.16445-20-james.morse@arm.com
|
|
The architecture specific parts of resctrl provide helpers like
is_mbm_total_enabled() and is_mbm_local_enabled() to hide accesses to the
rdt_mon_features bitmap.
Exposing a group of helpers between the architecture and filesystem code is
preferable to a single unsigned-long like rdt_mon_features. Helpers can be more
readable and have a well defined behaviour, while allowing architectures to hide
more complex behaviour.
Once the filesystem parts of resctrl are moved, these existing helpers can no
longer live in internal.h. Move them to include/linux/resctrl.h Once these are
exposed to the wider kernel, they should have a 'resctrl_arch_' prefix, to fit
the rest of the arch<->fs interface.
Move and rename the helpers that touch rdt_mon_features directly. is_mbm_event()
and is_mbm_enabled() are only called from rdtgroup.c, so can be moved into that
file.
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Fenghua Yu <fenghuay@nvidia.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Babu Moger <babu.moger@amd.com>
Reviewed-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Tested-by: Carl Worth <carl@os.amperecomputing.com> # arm64
Tested-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Tested-by: Peter Newman <peternewman@google.com>
Tested-by: Amit Singh Tomar <amitsinght@marvell.com> # arm64
Tested-by: Shanker Donthineni <sdonthineni@nvidia.com> # arm64
Tested-by: Babu Moger <babu.moger@amd.com>
Link: https://lore.kernel.org/r/20250311183715.16445-19-james.morse@arm.com
|
|
The for_each_*_rdt_resource() helpers walk the architecture's array of
structures, using the resctrl visible part as an iterator. These became
over-complex when the structures were split into a filesystem and
architecture-specific struct. This approach avoided the need to touch every
call site, and was done before there was a helper to retrieve a resource by
rid.
Once the filesystem parts of resctrl are moved to /fs/, both the arch's
resource array, and the definition of those structures is no longer
accessible. To support resctrl, each architecture would have to provide
equally complex macros.
Rewrite the macro to make use of resctrl_arch_get_resource(), and move these
to include/linux/resctrl.h so existing x86 arch code continues to use them.
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Fenghua Yu <fenghuay@nvidia.com>
Reviewed-by: Babu Moger <babu.moger@amd.com>
Tested-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Tested-by: Peter Newman <peternewman@google.com>
Tested-by: Amit Singh Tomar <amitsinght@marvell.com> # arm64
Tested-by: Shanker Donthineni <sdonthineni@nvidia.com> # arm64
Tested-by: Babu Moger <babu.moger@amd.com>
Link: https://lore.kernel.org/r/20250311183715.16445-18-james.morse@arm.com
|
|
rdt_get_mon_l3_config() is called from the arch's resctrl_arch_late_init(),
and initialises both architecture specific fields, such as hw_res->mon_scale
and resctrl filesystem fields by calling dom_data_init().
To separate the filesystem and architecture parts of resctrl, this function
needs splitting up.
Add resctrl_mon_resource_init() to do the filesystem specific work, and call
it from resctrl_init(). This runs later, but is still before the filesystem is
mounted and the rmid_ptrs[] array can be used.
[ bp: Massage commit message. ]
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Fenghua Yu <fenghuay@nvidia.com>
Reviewed-by: Babu Moger <babu.moger@amd.com>
Tested-by: Carl Worth <carl@os.amperecomputing.com> # arm64
Tested-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Tested-by: Peter Newman <peternewman@google.com>
Tested-by: Amit Singh Tomar <amitsinght@marvell.com> # arm64
Tested-by: Shanker Donthineni <sdonthineni@nvidia.com> # arm64
Tested-by: Babu Moger <babu.moger@amd.com>
Link: https://lore.kernel.org/r/20250311183715.16445-17-james.morse@arm.com
|
|
rdt_put_mon_l3_config() is called via the architecture's resctrl_arch_exit()
call, and appears to free the rmid_ptrs[] and closid_num_dirty_rmid[] arrays.
In reality this code is marked __exit, and is removed by the linker as resctrl
can't be built as a module.
To separate the filesystem and architecture parts of resctrl, this free()ing
work needs to be triggered by the filesystem, as these structures belong to
the filesystem code.
Rename rdt_put_mon_l3_config() to resctrl_mon_resource_exit() and call it from
resctrl_exit(). The kfree() is currently dependent on r->mon_capable.
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Fenghua Yu <fenghuay@nvidia.com>
Reviewed-by: Babu Moger <babu.moger@amd.com>
Tested-by: Carl Worth <carl@os.amperecomputing.com> # arm64
Tested-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Tested-by: Peter Newman <peternewman@google.com>
Tested-by: Amit Singh Tomar <amitsinght@marvell.com> # arm64
Tested-by: Shanker Donthineni <sdonthineni@nvidia.com> # arm64
Tested-by: Babu Moger <babu.moger@amd.com>
Link: https://lore.kernel.org/r/20250311183715.16445-16-james.morse@arm.com
|
|
On umount(), resctrl resets each resource back to its default configuration.
It only ever does this for all resources in one go.
reset_all_ctrls() is architecture specific as it works with struct
rdt_hw_resource.
Make reset_all_ctrls() an arch helper that resets one resource.
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Fenghua Yu <fenghuay@nvidia.com>
Reviewed-by: Babu Moger <babu.moger@amd.com>
Reviewed-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Tested-by: Peter Newman <peternewman@google.com>
Tested-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Tested-by: Amit Singh Tomar <amitsinght@marvell.com> # arm64
Tested-by: Shanker Donthineni <sdonthineni@nvidia.com> # arm64
Tested-by: Babu Moger <babu.moger@amd.com>
Link: https://lore.kernel.org/r/20250311183715.16445-15-james.morse@arm.com
|
|
When resctrl is fully factored into core and per-arch code, each arch will
need to use some resctrl common definitions in order to define its own
specializations and helpers. Following conventional practice, it would be
desirable to put the dependent arch definitions in an <asm/resctrl.h> header
that is included by the common <linux/resctrl.h> header. However, this can
make it awkward to avoid a circular dependency between <linux/resctrl.h> and
the arch header.
To avoid such dependencies, move the affected common types and constants into
a new header that does not need to depend on <linux/resctrl.h> or on the arch
headers.
The same logic applies to the monitor-configuration defines, move these too.
Some kind of enumeration for events is needed between the filesystem and
architecture code. Take the x86 definition as its convenient for x86.
The definition of enum resctrl_event_id is needed to allow the architecture
code to define resctrl_arch_mon_ctx_alloc() and resctrl_arch_mon_ctx_free().
The definition of enum resctrl_res_level is needed to allow the architecture
code to define resctrl_arch_set_cdp_enabled() and
resctrl_arch_get_cdp_enabled().
The bits for mbm_local_bytes_config et al are ABI, and must be the same on all
architectures. These are documented in Documentation/arch/x86/resctrl.rst
The maintainers entry for these headers was missed when resctrl.h was created.
Add a wildcard entry to match both resctrl.h and resctrl_types.h.
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Fenghua Yu <fenghuay@nvidia.com>
Reviewed-by: Babu Moger <babu.moger@amd.com>
Tested-by: Carl Worth <carl@os.amperecomputing.com> # arm64
Tested-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Tested-by: Peter Newman <peternewman@google.com>
Tested-by: Amit Singh Tomar <amitsinght@marvell.com> # arm64
Tested-by: Shanker Donthineni <sdonthineni@nvidia.com> # arm64
Tested-by: Babu Moger <babu.moger@amd.com>
Link: https://lore.kernel.org/r/20250311183715.16445-14-james.morse@arm.com
|
|
rdt_find_domain() finds a domain given a resource and a cache-id. This is
used by both the architecture code and the filesystem code.
After the filesystem code moves to live in /fs/, this helper is either
duplicated by all architectures, or needs exposing by the filesystem code.
Add the declaration to the global header file. As it's now globally visible,
and has only a handful of callers, swap the 'rdt' for 'resctrl'. Move the
function to live with its caller in ctrlmondata.c as the filesystem code will
not have anything corresponding to core.c.
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Fenghua Yu <fenghuay@nvidia.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Babu Moger <babu.moger@amd.com>
Reviewed-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Tested-by: Peter Newman <peternewman@google.com>
Tested-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Tested-by: Amit Singh Tomar <amitsinght@marvell.com> # arm64
Tested-by: Shanker Donthineni <sdonthineni@nvidia.com> # arm64
Tested-by: Babu Moger <babu.moger@amd.com>
Link: https://lore.kernel.org/r/20250311183715.16445-13-james.morse@arm.com
|
|
rdtgroup_init() needs exposing to the rest of the kernel so that arch code can
call it once it lives in core code. As this is one of the few functions
exposed, rename it to have "resctrl" in the name. The same goes for the exit
call.
Rename x86's arch code init functions for RDT to have an arch prefix to make
it clear these are part of the architecture code.
Co-developed-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Fenghua Yu <fenghuay@nvidia.com>
Reviewed-by: Babu Moger <babu.moger@amd.com>
Tested-by: Carl Worth <carl@os.amperecomputing.com> # arm64
Tested-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Tested-by: Peter Newman <peternewman@google.com>
Tested-by: Amit Singh Tomar <amitsinght@marvell.com> # arm64
Tested-by: Shanker Donthineni <sdonthineni@nvidia.com> # arm64
Tested-by: Babu Moger <babu.moger@amd.com>
Link: https://lore.kernel.org/r/20250311183715.16445-12-james.morse@arm.com
|
|
update_cpu_closid_rmid() takes a struct rdtgroup as an argument, which it uses
to update the local CPUs default pqr values. This is a problem once the
resctrl parts move out to /fs/, as the arch code cannot poke around inside
struct rdtgroup.
Rename update_cpu_closid_rmid() as resctrl_arch_sync_cpus_defaults() to be
used as the target of an IPI, and pass the effective CLOSID and RMID in a new
struct.
Co-developed-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Fenghua Yu <fenghuay@nvidia.com>
Reviewed-by: Babu Moger <babu.moger@amd.com>
Tested-by: Carl Worth <carl@os.amperecomputing.com> # arm64
Tested-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Tested-by: Peter Newman <peternewman@google.com>
Tested-by: Amit Singh Tomar <amitsinght@marvell.com> # arm64
Tested-by: Shanker Donthineni <sdonthineni@nvidia.com> # arm64
Tested-by: Babu Moger <babu.moger@amd.com>
Link: https://lore.kernel.org/r/20250311183715.16445-11-james.morse@arm.com
|
|
rdtgroup_rmdir_ctrl() and rdtgroup_rmdir_mon() set the per-CPU pqr_state for
CPUs that were part of the rmdir()'d group.
Another architecture might not have a 'pqr_state', its hardware may need the
values in a different format. MPAM's equivalent of RMID values are not unique,
and always need the CLOSID to be provided too.
There is only one caller that modifies a single value, (rdtgroup_rmdir_mon()).
MPAM always needs both CLOSID and RMID for the hardware value as these are
written to the same system register.
As rdtgroup_rmdir_mon() has the CLOSID on hand, only provide a helper to set
both values. These values are read by __resctrl_sched_in(), but may be written
by a different CPU without any locking, add READ/WRTE_ONCE() to avoid torn
values.
Co-developed-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Fenghua Yu <fenghuay@nvidia.com>
Reviewed-by: Babu Moger <babu.moger@amd.com>
Tested-by: Carl Worth <carl@os.amperecomputing.com> # arm64
Tested-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Tested-by: Peter Newman <peternewman@google.com>
Tested-by: Amit Singh Tomar <amitsinght@marvell.com> # arm64
Tested-by: Shanker Donthineni <sdonthineni@nvidia.com> # arm64
Tested-by: Babu Moger <babu.moger@amd.com>
Link: https://lore.kernel.org/r/20250311183715.16445-10-james.morse@arm.com
|
|
The struct rdt_resource default_ctrl is used by both the architecture code for
resetting the hardware controls, and sometimes by the filesystem code as the
default value for the schema, unless the bandwidth software controller is in
use.
Having the default exposed by the architecture code causes unnecessary
duplication for each architecture as the default value must be specified, but
can be derived from other schema properties. Now that the maximum bandwidth is
explicitly described, resctrl can derive the default value from the schema
format and the other resource properties.
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Fenghua Yu <fenghuay@nvidia.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Babu Moger <babu.moger@amd.com>
Tested-by: Carl Worth <carl@os.amperecomputing.com> # arm64
Tested-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Tested-by: Peter Newman <peternewman@google.com>
Tested-by: Amit Singh Tomar <amitsinght@marvell.com> # arm64
Tested-by: Shanker Donthineni <sdonthineni@nvidia.com> # arm64
Tested-by: Babu Moger <babu.moger@amd.com>
Link: https://lore.kernel.org/r/20250311183715.16445-9-james.morse@arm.com
|
