| Age | Commit message (Collapse) | Author |
|---|
|
Patch adds driver data & match table for cs42l43
multi-function codec on PTL-RVP at sdw link3.
Signed-off-by: Naveen Manohar <naveen.m@intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://patch.msgid.link/20250311003101.80967-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The ECC_CFG_ECC_DISABLE define is BIT(0). It's supposed to be used
directly instead of used as a shifter.
Fixes: 7304d1909080 ("spi: spi-qpic: add driver for QCOM SPI NAND flash Interface")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://patch.msgid.link/2f4b0a0b-2c03-41c0-8a4a-3d789a83832d@stanley.mountain
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Enable Quality of Service(QoS) support to speed up interrupt service
routine handle. Sometimes, a gic interrupt will be generated after
SPI transmission, but at this time the CPU is in an idle state and the
processing handler will be very slow. It takes time to exit the idle state
and then become active. This will cause the SPI handler to execute slowly
and cause SPI transfer timeouts.
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Link: https://patch.msgid.link/20250304024045.7788-1-leilk.liu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add support for SG2044 SPI NOR controller in Sophgo SoC.
Signed-off-by: Longbin Li <looong.bin@gmail.com>
Link: https://patch.msgid.link/20250304083548.10101-3-looong.bin@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add SPI NOR driver for SG2044, including read, write operations.
Signed-off-by: Longbin Li <looong.bin@gmail.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20250304083548.10101-2-looong.bin@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The pcf50633 was used as part of the OpenMoko devices but
the support for its main chip was recently removed in:
commit 61b7f8920b17 ("ARM: s3c: remove all s3c24xx support")
See https://lore.kernel.org/all/Z8z236h4B5A6Ki3D@gallifrey/
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Link: https://patch.msgid.link/20250311014959.743322-6-linux@treblig.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Sometimes I get a NULL pointer dereference at boot time in kobject_get()
with the following call stack:
anatop_regulator_probe()
devm_regulator_register()
regulator_register()
regulator_resolve_supply()
kobject_get()
By placing some extra BUG_ON() statements I could verify that this is
raised because probing of the 'dummy' regulator driver is not completed
('dummy_regulator_rdev' is still NULL).
In the JTAG debugger I can see that dummy_regulator_probe() and
anatop_regulator_probe() can be run by different kernel threads
(kworker/u4:*). I haven't further investigated whether this can be
changed or if there are other possibilities to force synchronization
between these two probe routines. On the other hand I don't expect much
boot time penalty by probing the 'dummy' regulator synchronously.
Cc: stable@vger.kernel.org
Fixes: 259b93b21a9f ("regulator: Set PROBE_PREFER_ASYNCHRONOUS for drivers that existed in 4.14")
Signed-off-by: Christian Eggers <ceggers@arri.de>
Link: https://patch.msgid.link/20250311091803.31026-1-ceggers@arri.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In hindsight, there were some crucial subtleties overlooked when moving
{of,acpi}_dma_configure() to driver probe time to allow waiting for
IOMMU drivers with -EPROBE_DEFER, and these have become an
ever-increasing source of problems. The IOMMU API has some fundamental
assumptions that iommu_probe_device() is called for every device added
to the system, in the order in which they are added. Calling it in a
random order or not at all dependent on driver binding leads to
malformed groups, a potential lack of isolation for devices with no
driver, and all manner of unexpected concurrency and race conditions.
We've attempted to mitigate the latter with point-fix bodges like
iommu_probe_device_lock, but it's a losing battle and the time has come
to bite the bullet and address the true source of the problem instead.
The crux of the matter is that the firmware parsing actually serves two
distinct purposes; one is identifying the IOMMU instance associated with
a device so we can check its availability, the second is actually
telling that instance about the relevant firmware-provided data for the
device. However the latter also depends on the former, and at the time
there was no good place to defer and retry that separately from the
availability check we also wanted for client driver probe.
Nowadays, though, we have a proper notion of multiple IOMMU instances in
the core API itself, and each one gets a chance to probe its own devices
upon registration, so we can finally make that work as intended for
DT/IORT/VIOT platforms too. All we need is for iommu_probe_device() to
be able to run the iommu_fwspec machinery currently buried deep in the
wrong end of {of,acpi}_dma_configure(). Luckily it turns out to be
surprisingly straightforward to bootstrap this transformation by pretty
much just calling the same path twice. At client driver probe time,
dev->driver is obviously set; conversely at device_add(), or a
subsequent bus_iommu_probe(), any device waiting for an IOMMU really
should *not* have a driver already, so we can use that as a condition to
disambiguate the two cases, and avoid recursing back into the IOMMU core
at the wrong times.
Obviously this isn't the nicest thing, but for now it gives us a
functional baseline to then unpick the layers in between without many
more awkward cross-subsystem patches. There are some minor side-effects
like dma_range_map potentially being created earlier, and some debug
prints being repeated, but these aren't significantly detrimental. Let's
make things work first, then deal with making them nice.
With the basic flow finally in the right order again, the next step is
probably turning the bus->dma_configure paths inside-out, since all we
really need from bus code is its notion of which device and input ID(s)
to parse the common firmware properties with...
Acked-by: Bjorn Helgaas <bhelgaas@google.com> # pci-driver.c
Acked-by: Rob Herring (Arm) <robh@kernel.org> # of/device.c
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/e3b191e6fd6ca9a1e84c5e5e40044faf97abb874.1740753261.git.robin.murphy@arm.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
At the moment, if of_iommu_configure() allocates dev->iommu itself via
iommu_fwspec_init(), then suffers a DT parsing failure, it cleans up the
fwspec but leaves the empty dev_iommu hanging around. So far this is
benign (if a tiny bit wasteful), but we'd like to be able to reason
about dev->iommu having a consistent and unambiguous lifecycle. Thus
make sure that the of_iommu cleanup undoes precisely whatever it did.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/d219663a3f23001f23d520a883ac622d70b4e642.1740753261.git.robin.murphy@arm.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Since iommu_init_device() was factored out, it is in fact the only
consumer of the ops which __iommu_probe_device() is resolving, so let it
do that itself rather than passing them in. This also puts the ops
lookup at a more logical point relative to the rest of the flow through
__iommu_probe_device().
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/fa4b6cfc67a352488b7f4e0b736008307ce9ac2e.1740753261.git.robin.murphy@arm.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
It turns out that deferred default domain creation leaves a subtle
race window during iommu_device_register() wherein a client driver may
asynchronously probe in parallel and get as far as performing DMA API
operations with dma-direct, only to be switched to iommu-dma underfoot
once the default domain attachment finally happens, with obviously
disastrous consequences. Even the wonky of_iommu_configure() path is at
risk, since iommu_fwspec_init() will no longer defer client probe as the
instance ops are (necessarily) already registered, and the "replay"
iommu_probe_device() call can see dev->iommu_group already set and so
think there's nothing to do either.
Fortunately we already have the right tool in the right place in the
form of iommu_device_use_default_domain(), which just needs to ensure
that said default domain is actually ready to *be* used. Deferring the
client probe shouldn't have too much impact, given that this only
happens while the IOMMU driver is probing, and thus due to kick the
deferred probe list again once it finishes.
Reported-by: Charan Teja Kalla <quic_charante@quicinc.com>
Fixes: 98ac73f99bc4 ("iommu: Require a default_domain for all iommu drivers")
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/e88b94c9b575034a2c98a48b3d383654cbda7902.1740753261.git.robin.murphy@arm.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The drivers doing their own fwspec parsing have no need to call
iommu_fwspec_free() since fwspecs were moved into dev_iommu, as
returning an error from .probe_device will tear down the whole lot
anyway. Move it into the private interface now that it only serves
for of_iommu to clean up in an error case.
I have no idea what mtk_v1 was doing in effectively guaranteeing
a NULL fwspec would be dereferenced if no "iommus" DT property was
found, so add a check for that to at least make the code look sane.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/36e245489361de2d13db22a510fa5c79e7126278.1740667667.git.robin.murphy@arm.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Since rtase_init_ring, which is called within rtase_sw_reset, adds ring
entries already present in the ring list back into the list, it causes
the ring list to form a cycle. This results in list_for_each_entry_safe
failing to find an endpoint during traversal, leading to an error.
Therefore, it is necessary to remove the previously added ring_list nodes
before calling rtase_init_ring.
Fixes: 079600489960 ("rtase: Implement net_device_ops")
Signed-off-by: Justin Lai <justinlai0215@realtek.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250306070510.18129-1-justinlai0215@realtek.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Hangbin Liu says:
====================
bonding: fix incorrect mac address setting
The mac address on backup slave should be convert from Solicited-Node
Multicast address, not from bonding unicast target address.
====================
Link: https://patch.msgid.link/20250306023923.38777-1-liuhangbin@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The correct mac address for NS target 2001:db8::254 is 33:33:ff:00:02:54,
not 33:33:00:00:02:54. The same with client maddress.
Fixes: 86fb6173d11e ("selftests: bonding: add ns multicast group testing")
Acked-by: Jay Vosburgh <jv@jvosburgh.net>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250306023923.38777-3-liuhangbin@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When validation on the backup slave is enabled, we need to validate the
Neighbor Solicitation (NS) messages received on the backup slave. To
receive these messages, the correct destination MAC address must be added
to the slave. However, the target in bonding is a unicast address, which
we cannot use directly. Instead, we should first convert it to a
Solicited-Node Multicast Address and then derive the corresponding MAC
address.
Fix the incorrect MAC address setting on both slave_set_ns_maddr() and
slave_set_ns_maddrs(). Since the two function names are similar. Add
some description for the functions. Also only use one mac_addr variable
in slave_set_ns_maddr() to save some code and logic.
Fixes: 8eb36164d1a6 ("bonding: add ns target multicast address to slave device")
Acked-by: Jay Vosburgh <jv@jvosburgh.net>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250306023923.38777-2-liuhangbin@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Ensure that the frag_list used for reassembly isn't shared with other
packets. This avoids incorrect reassembly when packets are cloned, and
prevents a memory leak due to circular references between fragments and
their skb_shared_info.
The upcoming MCTP-over-USB driver uses skb_clone which can trigger the
problem - other MCTP drivers don't share SKBs.
A kunit test is added to reproduce the issue.
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Fixes: 4a992bbd3650 ("mctp: Implement message fragmentation & reassembly")
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250306-matt-mctp-usb-v1-1-085502b3dd28@codeconstruct.com.au
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When a character array without a terminating NUL character has a static
initializer, GCC 15's -Wunterminated-string-initialization will only
warn if the array lacks the "nonstring" attribute[1]. Mark the arrays
with __nonstring to and correctly identify the char array as "not a C
string" and thereby eliminate the warning.
This effectively reverts the change in 4e7487245abc ("vboxsf: fix building
with GCC 15"), to add the annotation that has other uses (i.e. warning
if the string is ever used with C string APIs).
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=117178 [1]
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Brahmajit Das <brahmajit.xyz@gmail.com>
Cc: Christian Brauner <brauner@kernel.org>
Cc: linux-fsdevel@vger.kernel.org
Signed-off-by: Kees Cook <kees@kernel.org>
Link: https://lore.kernel.org/r/20250310222530.work.374-kees@kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
Update the __flush_tlb_range_op macro not to modify its parameters as
these are unexepcted semantics. In practice, this fixes the call to
mmu_notifier_arch_invalidate_secondary_tlbs() in
__flush_tlb_range_nosync() to use the correct range instead of an empty
range with start=end. The empty range was (un)lucky as it results in
taking the invalidate-all path that doesn't cause correctness issues,
but can certainly result in suboptimal perf.
This has been broken since commit 6bbd42e2df8f ("mmu_notifiers: call
invalidate_range() when invalidating TLBs") when the call to the
notifiers was added to __flush_tlb_range(). It predates the addition of
the __flush_tlb_range_op() macro from commit 360839027a6e ("arm64: tlb:
Refactor the core flush algorithm of __flush_tlb_range") that made the
bug hard to spot.
Fixes: 6bbd42e2df8f ("mmu_notifiers: call invalidate_range() when invalidating TLBs")
Signed-off-by: Piotr Jaroszynski <pjaroszynski@nvidia.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Alistair Popple <apopple@nvidia.com>
Cc: Raghavendra Rao Ananta <rananta@google.com>
Cc: SeongJae Park <sj@kernel.org>
Cc: Jason Gunthorpe <jgg@nvidia.com>
Cc: John Hubbard <jhubbard@nvidia.com>
Cc: Nicolin Chen <nicolinc@nvidia.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: iommu@lists.linux.dev
Cc: linux-mm@kvack.org
Cc: linux-kernel@vger.kernel.org
Cc: stable@vger.kernel.org
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Alistair Popple <apopple@nvidia.com>
Link: https://lore.kernel.org/r/20250304085127.2238030-1-pjaroszynski@nvidia.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
On the arm64 platform with 4K base page config, SECTION_SIZE_BITS is set
to 27, making one section 128M. The related page struct which vmemmap
points to is 2M then.
Commit c1cc1552616d ("arm64: MMU initialisation") optimizes the
vmemmap to populate at the PMD section level which was suitable
initially since hot plug granule is always one section(128M). However,
commit ba72b4c8cf60 ("mm/sparsemem: support sub-section hotplug")
introduced a 2M(SUBSECTION_SIZE) hot plug granule, which disrupted the
existing arm64 assumptions.
The first problem is that if start or end is not aligned to a section
boundary, such as when a subsection is hot added, populating the entire
section is wasteful.
The next problem is if we hotplug something that spans part of 128 MiB
section (subsections, let's call it memblock1), and then hotplug something
that spans another part of a 128 MiB section(subsections, let's call it
memblock2), and subsequently unplug memblock1, vmemmap_free() will clear
the entire PMD entry which also supports memblock2 even though memblock2
is still active.
Assuming hotplug/unplug sizes are guaranteed to be symmetric. Do the
fix similar to x86-64: populate to pages levels if start/end is not aligned
with section boundary.
Cc: stable@vger.kernel.org # v5.4+
Fixes: ba72b4c8cf60 ("mm/sparsemem: support sub-section hotplug")
Acked-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Zhenhua Huang <quic_zhenhuah@quicinc.com>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20250304072700.3405036-1-quic_zhenhuah@quicinc.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Provide coverage for all mnt_notify_add() instances.
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Link: https://lore.kernel.org/r/20250307204046.322691-1-mszeredi@redhat.com
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
A blocking notification chain uses a read-write semaphore to protect the
integrity of the chain. The semaphore is acquired for writing when
adding / removing notifiers to / from the chain and acquired for reading
when traversing the chain and informing notifiers about an event.
In case of the blocking switchdev notification chain, recursive
notifications are possible which leads to the semaphore being acquired
twice for reading and to lockdep warnings being generated [1].
Specifically, this can happen when the bridge driver processes a
SWITCHDEV_BRPORT_UNOFFLOADED event which causes it to emit notifications
about deferred events when calling switchdev_deferred_process().
Fix this by converting the notification chain to a raw notification
chain in a similar fashion to the netdev notification chain. Protect
the chain using the RTNL mutex by acquiring it when modifying the chain.
Events are always informed under the RTNL mutex, but add an assertion in
call_switchdev_blocking_notifiers() to make sure this is not violated in
the future.
Maintain the "blocking" prefix as events are always emitted from process
context and listeners are allowed to block.
[1]:
WARNING: possible recursive locking detected
6.14.0-rc4-custom-g079270089484 #1 Not tainted
--------------------------------------------
ip/52731 is trying to acquire lock:
ffffffff850918d8 ((switchdev_blocking_notif_chain).rwsem){++++}-{4:4}, at: blocking_notifier_call_chain+0x58/0xa0
but task is already holding lock:
ffffffff850918d8 ((switchdev_blocking_notif_chain).rwsem){++++}-{4:4}, at: blocking_notifier_call_chain+0x58/0xa0
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock((switchdev_blocking_notif_chain).rwsem);
lock((switchdev_blocking_notif_chain).rwsem);
*** DEADLOCK ***
May be due to missing lock nesting notation
3 locks held by ip/52731:
#0: ffffffff84f795b0 (rtnl_mutex){+.+.}-{4:4}, at: rtnl_newlink+0x727/0x1dc0
#1: ffffffff8731f628 (&net->rtnl_mutex){+.+.}-{4:4}, at: rtnl_newlink+0x790/0x1dc0
#2: ffffffff850918d8 ((switchdev_blocking_notif_chain).rwsem){++++}-{4:4}, at: blocking_notifier_call_chain+0x58/0xa0
stack backtrace:
...
? __pfx_down_read+0x10/0x10
? __pfx_mark_lock+0x10/0x10
? __pfx_switchdev_port_attr_set_deferred+0x10/0x10
blocking_notifier_call_chain+0x58/0xa0
switchdev_port_attr_notify.constprop.0+0xb3/0x1b0
? __pfx_switchdev_port_attr_notify.constprop.0+0x10/0x10
? mark_held_locks+0x94/0xe0
? switchdev_deferred_process+0x11a/0x340
switchdev_port_attr_set_deferred+0x27/0xd0
switchdev_deferred_process+0x164/0x340
br_switchdev_port_unoffload+0xc8/0x100 [bridge]
br_switchdev_blocking_event+0x29f/0x580 [bridge]
notifier_call_chain+0xa2/0x440
blocking_notifier_call_chain+0x6e/0xa0
switchdev_bridge_port_unoffload+0xde/0x1a0
...
Fixes: f7a70d650b0b6 ("net: bridge: switchdev: Ensure deferred event delivery on unoffload")
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/20250305121509.631207-1-amcohen@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The handling of the MST Connection Status Notify message is skipped if
the probing of the topology is still pending. Acquiring the
drm_dp_mst_topology_mgr::probe_lock for this in
drm_dp_mst_handle_up_req() is problematic: the task/work this function
is called from is also responsible for handling MST down-request replies
(in drm_dp_mst_handle_down_rep()). Thus drm_dp_mst_link_probe_work() -
holding already probe_lock - could be blocked waiting for an MST
down-request reply while drm_dp_mst_handle_up_req() is waiting for
probe_lock while processing a CSN message. This leads to the probe
work's down-request message timing out.
A scenario similar to the above leading to a down-request timeout is
handling a CSN message in drm_dp_mst_handle_conn_stat(), holding the
probe_lock and sending down-request messages while a second CSN message
sent by the sink subsequently is handled by drm_dp_mst_handle_up_req().
Fix the above by moving the logic to skip the CSN handling to
drm_dp_mst_process_up_req(). This function is called from a work
(separate from the task/work handling new up/down messages), already
holding probe_lock. This solves the above timeout issue, since handling
of down-request replies won't be blocked by probe_lock.
Fixes: ddf983488c3e ("drm/dp_mst: Skip CSN if topology probing is not done yet")
Cc: Wayne Lin <Wayne.Lin@amd.com>
Cc: Lyude Paul <lyude@redhat.com>
Cc: stable@vger.kernel.org # v6.6+
Reviewed-by: Wayne Lin <Wayne.Lin@amd.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250307183152.3822170-1-imre.deak@intel.com
|
|
Instead of using a custom script to detect and fail on undefined
references, use --no-undefined for all VDSO linker invocations.
Drop the now unused checkundef.sh script.
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Andreas Larsson <andreas@gaisler.com>
Link: https://lore.kernel.org/r/20250306-vdso-checkundef-v2-2-a26cc315fd73@linutronix.de
|
|
Instead of using a custom script to detect and fail on undefined
references, use --no-undefined for all VDSO linker invocations.
Drop the now unused checkundef.sh script.
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20250306-vdso-checkundef-v2-1-a26cc315fd73@linutronix.de
|
|
The original code used if statements to update discovered VPD pages when
found. This had the side-effect of not breaking the loop when a page was
found.
Use an idiomatic switch statement instead.
Signed-off-by: Chaohai Chen <wdhh6@aliyun.com>
Link: https://lore.kernel.org/r/20250226065802.234144-1-wdhh6@aliyun.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Geert Uytterhoeven <geert+renesas@glider.be> says:
Hi all,
Initialization of the UFS controller on R-Car S4-8 ES1.0 requires only
static values. However, other UFS controller variants (R-Car S4-8 ES 1.2)
require dynamic values, like those obtained from E-FUSE, and downloading
firmware.
Hence this patch series refactors the initialization code to prepare for
this, and adds support for the UFS controller on R-Car S4-8 ES1.2.
The accompanying DTS change is available at [1].
This has been tested on:
- Renesas Spider with R-Car S4-8 ES1.0 (broken before/after),
- Renesas S4 Starter Kit with R-Car S4-8 ES1.2 (works after).
Thanks for your comments!
[1] "[PATCH] arm64: dts: renesas: r8a779f4: Add UFS tuning parameters in
E-FUSE"
https://lore.kernel.org/3e4fca228eb049d54a1ae520104558505dbdf803.1741179629.git.geert+renesas@glider.be
[2] "[PATCH v2 0/5] scsi: ufs: renesas: Refactor code for other UFS
controller"
https://lore.kernel.org/20240709023550.1750333-1-yoshihiro.shimoda.uh@renesas.com
[3] "[PATCH 0/5] scsi: ufs: renesas: Refactor code for other UFS
controller"
https://lore.kernel.org/20240708120931.1703956-1-yoshihiro.shimoda.uh@renesas.com
Link: https://lore.kernel.org/r/cover.1741179611.git.geert+renesas@glider.be
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Add initialization code for R-Car S4-8 ES1.2 to improve transfer stability.
Using the new code requires downloading firmware and reading calibration
data from E-FUSE. If either fails, the driver falls back to the old
initialization code.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Co-developed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/97d83709495c764b2456d4d25846f5f48197cad0.1741179611.git.geert+renesas@glider.be
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Since some settings can be reused on other UFS controller (R-Car S4-8
ES1.2), add reusable functions.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/446d67b751a96645799de3aeefec539735aa78c8.1741179611.git.geert+renesas@glider.be
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Extract specific PHY setting of the 0x10a[df] registers into a new
function.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/110eafd1ee24f9db0285a5e2bca224e35962268a.1741179611.git.geert+renesas@glider.be
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
After refactoring the code, ufs_renesas_reg_control() is no longer needed,
because all operations are simple and can be called directly. Remove the
ufs_renesas_reg_control() helper function, and call udelay() directly.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/69500e4c18be1ca1de360f9e797e282ffef04004.1741179611.git.geert+renesas@glider.be
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Add support for returning read register values from
ufs_renesas_reg_control(), so ufs_renesas_set_phy() can use the existing
ufs_renesas_write_phy() helper. Remove the now unused code to save to,
set, and restore from a static array inside ufs_renesas_reg_control().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/9fa240a9dc0308d6675138f8434eccb77f051650.1741179611.git.geert+renesas@glider.be
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Since initialization of the UFS controller on R-Car S4-8 ES1.0 requires
only static values, the driver uses initialization data stored in the const
ufs_param[] array. However, other UFS controller variants (R-Car S4-8
ES1.2) require dynamic values, like those obtained from E-FUSE. Refactor
the initialization code to prepare for this.
This also reduces kernel size by almost 30 KiB.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/3520e27ac7ff512de6508f630eee3c1689a7c73d.1741179611.git.geert+renesas@glider.be
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
On R-Car S4-8 ES1.2, the E-FUSE block contains PLL and AFE tuning
parameters for the Universal Flash Storage controller. Document the
related NVMEM properties, and update the example.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/2f337169f8183d48b7d94ee13565fea804aade84.1741179611.git.geert+renesas@glider.be
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Add Task Abort support to handle SCSI command timeouts, ensuring recovery
and cleanup of timed-out commands. This completes the error handling
framework for mpi3mr driver, which already includes device reset, target
reset, bus reset, and host reset.
Co-developed-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Link: https://lore.kernel.org/r/20250304191453.12994-1-chandrakanth.patil@broadcom.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The log statement reports the packet status code as the hv status code
which causes confusion when debugging as "hv" might refer to a hypervisor,
and sometimes to the host part of the Hyper-V virtualization stack.
Fix the name of the datum being logged to clearly indicate the component
reporting the error. Also log it in hexadecimal everywhere for consistency.
Signed-off-by: Roman Kisel <romank@linux.microsoft.com>
Link: https://lore.kernel.org/r/20250304000940.9557-2-romank@linux.microsoft.com
Reviewed-by: Easwar Hariharan <eahariha@linux.microsoft.com>
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Most of the module parameters are only used locally in the same C file; so
static them.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Link: https://lore.kernel.org/r/20250309145044.38586-1-linux@treblig.org
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Most of the module parameters are only used locally in the same C file; so
static them.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Link: https://lore.kernel.org/r/20250309143348.32896-1-linux@treblig.org
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The original support for incrementally consumed buffers didn't allow it
to be used with bundles, with the assumption being that incremental
buffers are generally larger, and hence there's less of a nedd to
support it.
But that assumption may not be correct - it's perfectly viable to use
smaller buffers with incremental consumption, and there may be valid
reasons for an application or framework to do so.
As there's really no need to explicitly disable bundles with
incrementally consumed buffers, allow it. This actually makes the peek
side cheaper and simpler, with the completion side basically the same,
just needing to iterate for the consumed length.
Reported-by: Norman Maurer <norman_maurer@apple.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
This reverts commit 2a51c327d4a4a2eb62d67f4ea13a17efd0f25c5c.
The kernel registered bvecs do use the iov_iter_advance() API, so we
can't rely on this simplification anymore.
Fixes: 27cb27b6d5ea40 ("io_uring: add support for kernel registered bvecs")
Reported-by: Caleb Sander Mateos <csander@purestorage.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Caleb Sander Mateos <csander@purestorage.com>
Link: https://lore.kernel.org/r/20250310184825.569371-1-kbusch@meta.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Add UBLK_TEST_QUIET, so we can print test result(PASS/SKIP/FAIL) only.
Also always run from test script's current directory, then the same test
script can be started from other work directory.
This way helps a lot to reuse this test source code and scripts for
other projects(liburing, blktests, ...)
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20250303124324.3563605-12-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Add stress_test_01 for running IO vs. killing ublk server, so io_uring exit &
cancel code path can be covered, same with ublk's cancel code path.
Especially IO buffer lifetime is one big thing for ublk zero copy, the added
test can verify if this area works as expected.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20250303124324.3563605-11-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Add stress_test_01 for running IO vs. removing device for verifying that
ublk device removal can work as expected when heavy IO workloads are in
progress.
null, loop and loop/zc are covered in this tests.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20250303124324.3563605-10-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Load ublk_drv module in _prep_test(), and unload it in _cleanup_test(),
so that test can always be done in consistent state.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20250303124324.3563605-9-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Move zero copy feature check into _add_ublk_dev() since we will have
more tests which requires to cover zero copy.
Then one check function of _check_add_dev() has to be added for dealing
with cleanup since '_add_ublk_dev()' is run in sub-shell, and we can't
exit from it to terminal shell.
Meantime always return error code from _add_ublk_dev().
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20250303124324.3563605-8-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
More devices can be created in single tests, so simply remove all
ublk devices in _cleanup_test(), meantime remove the ${dev_id} argument
of _cleanup_test().
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20250303124324.3563605-7-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Add shellcheck, meantime fixes all warnings.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20250303124324.3563605-6-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The argument of '-a' doesn't follow any value, so fix it by putting it
with '-z' together.
Fixes: bedc9cbc5f97 ("selftests: ublk: add ublk zero copy test")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Link: https://lore.kernel.org/r/20250303124324.3563605-5-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Martin has left AMD and no longer works on the sfc driver.
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Link: https://patch.msgid.link/20250307154731.211368-1-edward.cree@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Taehee Yoo says:
====================
eth: bnxt: fix several bugs in the bnxt module
The first fixes setting incorrect skb->truesize.
When xdp-mb prog returns XDP_PASS, skb is allocated and initialized.
Currently, The truesize is calculated as BNXT_RX_PAGE_SIZE *
sinfo->nr_frags, but sinfo->nr_frags is flushed by napi_build_skb().
So, it stores sinfo before calling napi_build_skb() and then use it
for calculate truesize.
The second fixes kernel panic in the bnxt_queue_mem_alloc().
The bnxt_queue_mem_alloc() accesses rx ring descriptor.
rx ring descriptors are allocated when the interface is up and it's
freed when the interface is down.
So, if bnxt_queue_mem_alloc() is called when the interface is down,
kernel panic occurs.
This patch makes the bnxt_queue_mem_alloc() return -ENETDOWN if rx ring
descriptors are not allocated.
The third patch fixes kernel panic in the bnxt_queue_{start | stop}().
When a queue is restarted bnxt_queue_{start | stop}() are called.
These functions set MRU to 0 to stop packet flow and then to set up the
remaining things.
MRU variable is a member of vnic_info[] the first vnic_info is for
default and the second is for ntuple.
The first vnic_info is always allocated when interface is up, but the
second is allocated only when ntuple is enabled.
(ethtool -K eth0 ntuple <on | off>).
Currently, the bnxt_queue_{start | stop}() access
vnic_info[BNXT_VNIC_NTUPLE] regardless of whether ntuple is enabled or
not.
So kernel panic occurs.
This patch make the bnxt_queue_{start | stop}() use bp->nr_vnics instead
of BNXT_VNIC_NTUPLE.
The fourth patch fixes a warning due to checksum state.
The bnxt_rx_pkt() checks whether skb->ip_summed is not CHECKSUM_NONE
before updating ip_summed. if ip_summed is not CHECKSUM_NONE, it WARNS
about it. However, the bnxt_xdp_build_skb() is called in XDP-MB-PASS
path and it updates ip_summed earlier than bnxt_rx_pkt().
So, in the XDP-MB-PASS path, the bnxt_rx_pkt() always warns about
checksum.
Updating ip_summed at the bnxt_xdp_build_skb() is unnecessary and
duplicate, so it is removed.
The fifth patch fixes a kernel panic in the
bnxt_get_queue_stats{rx | tx}().
The bnxt_get_queue_stats{rx | tx}() callback functions are called when
a queue is resetting.
These internally access rx and tx rings without null check, but rings
are allocated and initialized when the interface is up.
So, these functions are called when the interface is down, it
occurs a kernel panic.
The sixth patch fixes memory leak in queue reset logic.
When a queue is resetting, tpa_info is allocated for the new queue and
tpa_info for an old queue is not used anymore.
So it should be freed, but not.
The seventh patch makes net_devmem_unbind_dmabuf() ignore -ENETDOWN.
When devmem socket is closed, net_devmem_unbind_dmabuf() is called to
unbind/release resources.
If interface is down, the driver returns -ENETDOWN.
The -ENETDOWN return value is not an actual error, because the interface
will release resources when the interface is down.
So, net_devmem_unbind_dmabuf() needs to ignore -ENETDOWN.
The last patch adds XDP testcases to
tools/testing/selftests/drivers/net/ping.py.
====================
Link: https://patch.msgid.link/20250309134219.91670-1-ap420073@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
