| Age | Commit message (Collapse) | Author |
|---|
|
Rename local variable 'ec_corr' into 'ec_err' to make the code a little bit
more readable. 'ec_err' is more appropriate because it sounds more like 'error
when EC was read' and it looks more logical because we use it together with
'err'. Just a minor nicification which should improve the rather complex
scanning code.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
Currently UBI has one small flaw - when we read EC or VID header, but find only
0xFF bytes, we return UBI_IO_FF and do not report whether we had bit-flips or
not. In case of the VID header, the scanning code adds this PEB to the free list,
even though there were bit-flips.
Imagine the following situation: we start writing VID header to a PEB and have a
power cut, so the PEB becomes unstable. When we scan and read the PEB, we get
a bit-flip. Currently, UBI would just ignore this and treat the PEB as free. This
patch changes UBI behavior and now UBI will schedule this PEB for erasure.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
The 'UBI_IO_PEB_EMPTY' and 'UBI_IO_PEB_FREE' are essentially the same
and mean that there are only 0xFF bytes instead of headers. Simplify
UBI a little by turning them into a single 'UBI_IO_FF' error code.
Also, stop maintaining commentaries in 'ubi_io_read_vid_hdr()' which are
almost identical to commentaries in 'ubi_io_read_ec_hdr()'.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
Rename UBI_IO_BAD_HDR_READ into UBI_IO_BAD_HDR_EBADMSG which is presumably more
self-documenting and readable. Indeed, the '_READ' suffix does not tell much and
even confuses, while '_EBADMSG' tells about uncorrectable ECC error, because we
use -EBADMSG all over the place to represent ECC errors.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
One line was longer than 80 lines, make it shorter.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
Cleanup the Kconfig for UBI by using menuconfig to enable/disable the entire
driver. Remove the dependency checks for MTD_UBI and MTD_UBI_DEBUG by
wrapping the options in if/endif blocks and remove any redundant checks.
Remove all default n since that is the Kconfig default. Change menu "Additional
UBI debugging messages" into a comment to remove one menu level.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
This code has been broken forever, but in several different and
creative ways.
So far as I can work out, the R6040 MAC filter has 4 exact-match
entries, the first of which the driver uses for its assigned unicast
address, plus a 64-entry hash-based filter for multicast addresses
(maybe unicast as well?).
The original version of this code would write the first 4 multicast
addresses as exact-match entries from offset 1 (bug #1: there is no
entry 4 so this could write to some PHY registers). It would fill the
remainder of the exact-match entries with the broadcast address (bug #2:
this would overwrite the last used entry). If more than 4 multicast
addresses were configured, it would set up the hash table, write some
random crap to the MAC control register (bug #3) and finally walk off
the end of the list when filling the exact-match entries (bug #4).
All of this seems to be pointless, since it sets the promiscuous bit
when the interface is made promiscuous or if >4 multicast addresses
are enabled, and never clears it (bug #5, masking bug #2).
The recent(ish) changes to the multicast list fixed bug #4, but
completely removed the limit on iteration over the exact-match entries
(bug #6).
Bug #4 was reported as
<https://bugzilla.kernel.org/show_bug.cgi?id=15355> and more recently
as <http://bugs.debian.org/600155>. Florian Fainelli attempted to fix
these in commit 3bcf8229a8c49769e48d3e0bd1e20d8e003f8106, but that
actually dealt with bugs #1-3, bug #4 having been fixed in mainline at
that point.
That commit fixes the most important current bug #6.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: stable@kernel.org [2.6.35 only]
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Changed <module>-objs to <module>-y in Makefile.
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Make hifn_795x::hifn_remove() call cancel_delayed_work_sync() instead
of calling cancel_delayed_work() followed by flush_scheduled_work().
This is to prepare for the deprecation and removal of
flush_scheduled_work().
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Remove a couple of pointless header file includes.
Fixes a compile bug caused by header file include dependencies with
"irq: Add tracepoint to softirq_raise" within linux-next.
Reported-by: Sachin Sant <sachinp@in.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
[ cherry-picked from the s390 tree to fix "2bf2160: irq: Add tracepoint to softirq_raise" ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Ugly #include dependencies. We need to have local_softirq_pending()
defined before it gets used in <linux/interrupt.h>. But <asm/hardirq.h>
provides the definition *after* this #include chain:
<linux/irq.h>
<asm/irq.h>
<asm/hw_irq.h>
<linux/interrupt.h>
Signed-off-by: Tony Luck <tony.luck@intel.com>
[ cherry-picked from the ia64 tree to fix "2bf2160: irq: Add tracepoint to softirq_raise" ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Convert inetdev_by_index() to not increment in_dev refcount.
Callers hold RCU or RTNL, and should not decrement in_dev refcount.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We hold RTNL in ip_mc_find_dev(), no need to touch device refcount.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
futex_wait() is leaking key references due to futex_wait_setup()
acquiring an additional reference via the queue_lock() routine. The
nested key ref-counting has been masking bugs and complicating code
analysis. queue_lock() is only called with a previously ref-counted
key, so remove the additional ref-counting from the queue_(un)lock()
functions.
Also futex_wait_requeue_pi() drops one key reference too many in
unqueue_me_pi(). Remove the key reference handling from
unqueue_me_pi(). This was paired with a queue_lock() in
futex_lock_pi(), so the count remains unchanged.
Document remaining nested key ref-counting sites.
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Reported-and-tested-by: Matthieu Fertré<matthieu.fertre@kerlabs.com>
Reported-by: Louis Rilling<louis.rilling@kerlabs.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: John Kacur <jkacur@redhat.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
LKML-Reference: <4CBB17A8.70401@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@kernel.org
|
|
If you are genuinely using one of these legacy MCA drivers
then you are tragically on hardware where you really don't
have the extra CPU cycles to be wasting on this.
In addition, it makes two less cases for people to inadvertently
blindly copy flags from without explicitly thinking whether it
makes sense -- see the addition to feature-removal.txt as per
commit 9d9b8fb0e5ebf4b0398e579f6061d4451fea3242.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The dabusb device driver is sufficiently serialized using
its own mutex, no need for the big kernel lock here
in addition.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
The sunrpc cache_ioctl function does not need the big kernel lock
because it uses its own queue_lock already.
rpc_pipe_ioctl apparently should be using i_lock like the other
operations on the pipe file descriptor do.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
According to commit 5e3d20a68f63fc5a310687d81956c3b96e488b84
(init: Remove the BKL from startup code) these sparse notations
should be removed also.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
According to Jens, this code does not need the BKL at all,
it is sufficiently serialized by bd_mutex.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Jens Axboe <jaxboe@fusionio.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
|
|
The big kernel lock is going away, so make sure
that if it is disabled by Kconfig, we do not
try to validate it, which would result in
compile errors.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
|
|
The dvb core only uses the big kernel lock in the open
and ioctl functions, which means it can be replaced with
a dvb specific mutex. Fortunately, all the ioctl functions
go through dvb_usercopy, so we can move the serialization
in there.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: linux-media@vger.kernel.org
|
|
The bt8xx driver only uses the big kernel lock in its dst_ca_ioctl
function and never to serialize against other code, so we can
trivially replace it with a private mutex.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: linux-media@vger.kernel.org
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
This driver already has a global mutex, so let's just
use that in the open function instead of the BKL.
It may not even be needed there, but this patch should
have the smallest impact.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Mark Gross <mark.gross@intel.com>
|
|
RAW_SETBIND and RAW_GETBIND 32bit versions are fscked in interesting ways.
1) fs/compat_ioctl.c has COMPATIBLE_IOCTL(RAW_SETBIND) followed by
HANDLE_IOCTL(RAW_SETBIND, raw_ioctl). The latter is ignored.
2) on amd64 (and itanic) the damn thing is broken - we have int + u64 + u64
and layouts on i386 and amd64 are _not_ the same. raw_ioctl() would
work there, but it's never called due to (1). As it is, i386 /sbin/raw
definitely doesn't work on amd64 boxen.
3) switching to raw_ioctl() as is would *not* work on e.g. sparc64 and ppc64,
which would be rather sad, seeing that normal userland there is 32bit.
The thing is, slapping __packed on the struct in question does not DTRT -
it eliminates *all* padding. The real solution is to use compat_u64.
4) of course, all that stuff has no business being outside of raw.c in the
first place - there should be ->compat_ioctl() for /dev/rawctl instead of
messing with compat_ioctl.c.
[akpm@linux-foundation.org: coding-style fixes]
[arnd@arndb.de: port to 2.6.36]
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Three uml device drivers still use the big kernel lock,
but all of them can be safely converted to using
a per-driver mutex instead. Most likely this is not
even necessary, so after further review these can
and should be removed as well.
The exec system call no longer requires the BKL either,
so remove it from there, too.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: user-mode-linux-devel@lists.sourceforge.net
|
|
Commit a25909a4 (lockdep: Add an in_workqueue_context() lockdep-based
test function) added in_workqueue_context() but there hasn't been any
in-kernel user and the lockdep annotation in workqueue is scheduled to
change. Remove the unused function.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
|
|
The documentation for schedule_on_each_cpu() states that it calls a
function on each online CPU from keventd. This can easily be
interpreted as an asyncronous call because the description does not
mention that flush_work is called. Clarify that it is synchronous.
tj: rephrased a bit
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
lru_add_drain_all() uses schedule_on_each_cpu() which is synchronous.
There is no reason to call flush_scheduled_work() after
lru_add_drain_all(). Drop the spurious calls.
This is to prepare for the deprecation and removal of
flush_scheduled_work().
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Reviewed-by: Minchan Kim <minchan.kim@gmail.com>
Acked-by: Mel Gorman <mel@csn.ul.ie>
|
|
IPv6 encapsulation uses a bad source address for the tunnel.
i.e. VIP will be used as local-addr and encap. dst addr.
Decapsulation will not accept this.
Example
LVS (eth1 2003::2:0:1/96, VIP 2003::2:0:100)
(eth0 2003::1:0:1/96)
RS (ethX 2003::1:0:5/96)
tcpdump
2003::2:0:100 > 2003::1:0:5: IP6 (hlim 63, next-header TCP (6) payload length: 40) 2003::3:0:10.50991 > 2003::2:0:100.http: Flags [S], cksum 0x7312 (correct), seq 3006460279, win 5760, options [mss 1440,sackOK,TS val 1904932 ecr 0,nop,wscale 3], length 0
In Linux IPv6 impl. you can't have a tunnel with an any cast address
receiving packets (I have not tried to interpret RFC 2473)
To have receive capabilities the tunnel must have:
- Local address set as multicast addr or an unicast addr
- Remote address set as an unicast addr.
- Loop back addres or Link local address are not allowed.
This causes us to setup a tunnel in the Real Server with the
LVS as the remote address, here you can't use the VIP address since it's
used inside the tunnel.
Solution
Use outgoing interface IPv6 address (match against the destination).
i.e. use ip6_route_output() to look up the route cache and
then use ipv6_dev_get_saddr(...) to set the source address of the
encapsulated packet.
Additionally, cache the results in new destination
fields: dst_cookie and dst_saddr and properly check the
returned dst from ip6_route_output. We now add xfrm_lookup
call only for the tunneling method where the source address
is a local one.
Signed-off-by:Hans Schillstrom <hans.schillstrom@ericsson.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
|
|
This patch allows to listen to events that inform about
expectations destroyed.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
|
|
cciss: fix PCI IDs for new controllers
This patch fixes the botched up PCI IDs of new controllers. Please consider
this patch for inclusion.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
On a system that support intr-rempping when booting with "intremap=off"
[ 177.895501] BUG: unable to handle kernel NULL pointer dereference at 00000000000000f8
[ 177.913316] IP: [<ffffffff8145fc18>] free_irte+0x47/0xc0
...
[ 178.173326] Call Trace:
[ 178.173574] [<ffffffff810515b4>] destroy_irq+0x3a/0x75
[ 178.192934] [<ffffffff81051834>] arch_teardown_msi_irq+0xe/0x10
[ 178.193418] [<ffffffff81458dc3>] arch_teardown_msi_irqs+0x56/0x7f
[ 178.213021] [<ffffffff81458e79>] free_msi_irqs+0x8d/0xeb
Call free_irte only when interrupt remapping is enabled.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <4CBCB274.7010108@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Commit c3f00c70 ("perf: Separate find_get_context() from event
initialization") changed the generic perf_event code to call
perf_event_alloc, which calls the arch-specific event_init code,
before looking up the context for the new event. Unfortunately,
power_pmu_event_init uses event->ctx->task to see whether the
new event is a per-task event or a system-wide event, and thus
crashes since event->ctx is NULL at the point where
power_pmu_event_init gets called.
(The reason it needs to know whether it is a per-task event is
because there are some hardware events on Power systems which
only count when the processor is not idle, and there are some
fixed-function counters which count such events. For example,
the "run cycles" event counts cycles when the processor is not
idle. If the user asks to count cycles, we can use "run cycles"
if this is a per-task event, since the processor is running when
the task is running, by definition. We can't use "run cycles"
if the user asks for "cycles" on a system-wide counter.)
Fortunately the information we need is in the
event->attach_state field, so we just use that instead.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <20101019055535.GA10398@drongo>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Reported-by: Alexey Kardashevskiy <aik@au1.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Conflicts:
block/blk-core.c
drivers/block/loop.c
mm/swapfile.c
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
/proc/diskstats would display a strange output as follows.
$ cat /proc/diskstats |grep sda
8 0 sda 90524 7579 102154 20464 0 0 0 0 0 14096 20089
8 1 sda1 19085 1352 21841 4209 0 0 0 0 4294967064 15689 4293424691
~~~~~~~~~~
8 2 sda2 71252 3624 74891 15950 0 0 0 0 232 23995 1562390
8 3 sda3 54 487 2188 92 0 0 0 0 0 88 92
8 4 sda4 4 0 8 0 0 0 0 0 0 0 0
8 5 sda5 81 2027 2130 138 0 0 0 0 0 87 137
Its reason is the wrong way of accounting hd_struct->in_flight. When a bio is
merged into a request belongs to different partition by ELEVATOR_FRONT_MERGE.
The detailed root cause is as follows.
Assuming that there are two partition, sda1 and sda2.
1. A request for sda2 is in request_queue. Hence sda1's hd_struct->in_flight
is 0 and sda2's one is 1.
| hd_struct->in_flight
---------------------------
sda1 | 0
sda2 | 1
---------------------------
2. A bio belongs to sda1 is issued and is merged into the request mentioned on
step1 by ELEVATOR_BACK_MERGE. The first sector of the request is changed
from sda2 region to sda1 region. However the two partition's
hd_struct->in_flight are not changed.
| hd_struct->in_flight
---------------------------
sda1 | 0
sda2 | 1
---------------------------
3. The request is finished and blk_account_io_done() is called. In this case,
sda2's hd_struct->in_flight, not a sda1's one, is decremented.
| hd_struct->in_flight
---------------------------
sda1 | -1
sda2 | 1
---------------------------
The patch fixes the problem by caching the partition lookup
inside the request structure, hence making sure that the increment
and decrement will always happen on the same partition struct. This
also speeds up IO with accounting enabled, since it cuts down on
the number of lookups we have to do.
When reloading partition tables, quiesce IO to ensure that no
request references to the partition struct exists. When it is safe
to free the partition table, the IO for that device is restarted
again.
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: stable@kernel.org
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-2.6-trace into perf/core
|
|
This patch fixes build error about GPIO address due to
conflict of commit 4d914705 and 19a2c065.
- commit 4d914705: Fix on GPIO base addresses
- commit 19a2c065: Moves initial map for merging S5P64X0
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Conflicts:
arch/arm/kernel/head-common.S
|
|
'st-ux' and 'unwind' into devel
|
|
When DYNAMIC_FTRACE is enabled and we use the C version of recordmcount,
all objects are run through the recordmcount program to create a
separate section that stores all the callers of mcount.
The build process has a special file: scripts/mod/empty.o. This is
built from empty.c which is literally an empty file (except for a
single comment). This file is used to find information about the target
elf format, like endianness and word size.
The problem comes up when we need to build recordmcount. The
build process requires that empty.o is built first. The build rules
for empty.o will try to execute recordmcount on the empty.o file.
We get an error that recordmcount does not exist.
To avoid this recursion, the build file will skip running recordmcount
if the file that it is building is script/mod/empty.o.
[ extra comment Suggested-by: Sam Ravnborg <sam@ravnborg.org> ]
Reported-by: Ingo Molnar <mingo@elte.hu>
Tested-by: Ingo Molnar <mingo@elte.hu>
Cc: Michal Marek <mmarek@suse.cz>
Cc: linux-kbuild@vger.kernel.org
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
version.
Update Kconfig text accordingly.
Signed-off-by: srinidhi kasagar <srinidhi.kasagar@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
* 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus:
MIPS: Enable ISA_DMA_API config to fix build failure
MIPS: 32-bit: Fix build failure in asm/fcntl.h
MIPS: Remove all generated vmlinuz* files on "make clean"
MIPS: do_sigaltstack() expects userland pointers
MIPS: Fix error values in case of bad_stack
MIPS: Sanitize restart logics
MIPS: secure_computing, syscall audit: syscall number should in r2, not r0.
MIPS: Don't block signals if we'd failed to setup a sigframe
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: evdev - fix EVIOCSABS regression
Input: evdev - fix Ooops in EVIOCGABS/EVIOCSABS
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
firewire: ohci: fix TI TSB82AA2 regression since 2.6.35
|
|
Get rid of init_MUTEX[_LOCKED]() and use sema_init() instead.
(Ported to current XFS code by <aelder@sgi.com>.)
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
|
|
This patch reverts the driver to enabling/disabling the NFC interrupt
mask rather than enabling/disabling the system interrupt. This cleans
up the driver so that it doesn't rely on interrupts being disabled
within the interrupt handler.
For i.MX21 we keep the current behaviour, that is calling
enable_irq/disable_irq_nosync to enable/disable interrupts. This patch
is based on earlier work by John Ogness.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: John Ogness <john.ogness@linutronix.de>
Tested-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch adds support for 32bit project quota identifiers.
On disk format is backward compatible with 16bit projid numbers. projid
on disk is now kept in two 16bit values - di_projid_lo (which holds the
same position as old 16bit projid value) and new di_projid_hi (takes
existing padding) and converts from/to 32bit value on the fly.
xfs_admin (for existing fs), mkfs.xfs (for new fs) needs to be used
to enable PROJID32BIT support.
Signed-off-by: Arkadiusz Miśkiewicz <arekm@maven.pl>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
|
|
Stop having two different names for many buffer functions and use
the more descriptive xfs_buf_* names directly.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
|
|
We're not actually passing around credentials inside XFS for a while
now, so remove all xfs_cred.h with it's cred_t typedef and all
instances of it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
|
|
This header only provides one extern that isn't actually declared
anywhere, and shadowed by a macro.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
|
