| Age | Commit message (Collapse) | Author |
|---|
|
Remove unused code which was used only with deprecated HW
which didn't support vlan actions.
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
remove_flow_enable event isn't really needed as it will be
triggered once user and/or XFRM core explicitly asked to delete
state. In such situation, we won't be interested in any event
at all.
So don't trigger and listen to remove_flow_enable event.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
In case where after reset the PCI link is not ready within timeout, skip
reading device ID as if there is no PCI link up we can't have FW
response to pci config cycles either.
This also fixes err value not used and overwritten in such flow.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Commit 90e7cb78b815 ("net/mlx5: fix missing mutex_unlock in
mlx5_fw_fatal_reporter_err_work()") introduced another checking of
MLX5_DROP_HEALTH_NEW_WORK. At this point, the first check of
MLX5_DROP_HEALTH_NEW_WORK is redundant and so is the lock that
protects it.
Remove the lock and rename MLX5_DROP_HEALTH_NEW_WORK to reflect these
changes.
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Clang warns about excessive stack usage on 32-bit targets:
drivers/net/ethernet/mellanox/mlx5/core/en_main.c:3597:12: error: stack frame size (1184) exceeds limit (1024) in 'mlx5e_setup_tc' [-Werror,-Wframe-larger-than]
static int mlx5e_setup_tc(struct net_device *dev, enum tc_setup_type type,
It turns out that both the mlx5e_setup_tc_mqprio_dcb() function and
the mlx5e_safe_switch_params() function it calls have a copy of
'struct mlx5e_params' on the stack, and this structure is fairly
large.
Use dynamic allocation for the inner one.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
rxrpc_recvmsg_data() schedules an ACK to be transmitted every time at least
two packets have been consumed and any time it runs out of data and would
return -EAGAIN to the caller. Both events may occur within a single loop,
however, and if the I/O thread is quick enough it may send duplicate ACKs.
The ACKs are sent to inform the peer that more space has been made in the
local Rx window, but the I/O thread is going to send an ACK every couple of
DATA packets anyway, so we end up sending a lot more ACKs than we really
need to.
So reduce the rate at which recvmsg() schedules ACKs, such that if the I/O
thread sends ACKs at its normal faster rate, recvmsg() won't actually
schedule ACKs until the Rx flow stops (call->rx_consumed is cleared any
time we transmit an ACK for that call, resetting the counter used by
recvmsg).
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
Log ack.rwind in the rxrpc_tx_ack tracepoint. This value is useful to see
as it represents flow-control information to the peer.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
If an rxrpc call is given a poke, it will get woken up unconditionally,
even if there's already a poke pending (for which there will have been a
wake) or if the call refcount has gone to 0.
Fix this by only waking the call if it is still referenced and if it
doesn't already have a poke pending.
Fixes: 15f661dc95da ("rxrpc: Implement a mechanism to send an event notification to a call")
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
Use consume_skb() rather than kfree_skb_reason().
Reported-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree fixes from Rob Herring:
- Fix handling of multiple OF framebuffer devices
- Fix booting on Socionext Synquacer with bad 'dma-ranges' entries
- Add DT binding .yamllint to .gitignore
* tag 'devicetree-fixes-for-6.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: interrupt-controller: arm,gic-v3: Fix typo in description of msi-controller property
dt-bindings: Fix .gitignore
of/address: Return an error when no valid dma-ranges are found
of: Make OF framebuffer device names unique
|
|
Add missing xdp_features field description in the struct net_device
documentation. This patch fix the following warning:
[...]
./include/linux/netdevice.h:2375: warning: Function parameter or member 'xdp_features' not described in 'net_device'
[...]
Fixes: d3d854fd6a1d ("netdev-genl: create a simple family for netdev stuff")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/7878544903d855b49e838c9d59f715bde0b5e63b.1675705948.git.lorenzo@kernel.org
|
|
Now virtio-net supports xdp multi-buffer so add it to xdp_features.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Link: https://lore.kernel.org/bpf/60c76cd63a0246db785606e8891b925fd5c9bf06.1675763384.git.lorenzo@kernel.org
|
|
In order to properly set errno, rely on libbpf_err utility routine in
bpf_xdp_query() to return an error to the caller.
Fixes: 04d58f1b26a4 ("libbpf: add API to get XDP/XSK supported features")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/827d40181f9f90fb37702f44328e1614df7c0503.1675768112.git.lorenzo@kernel.org
|
|
Don't set EXTRA_CFLAGS to HOSTCFLAGS, ensure CROSS_COMPILE isn't
passed through.
Signed-off-by: Ian Rogers <irogers@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Link: https://lore.kernel.org/bpf/20230202224253.40283-1-irogers@google.com
|
|
Making resolve_btfids to be compiled as host program so
we can avoid cross compile issues as reported by Nathan.
Also we no longer need HOST_OVERRIDES for BINARY target,
just for 'prepare' targets.
Fixes: 13e07691a16f ("tools/resolve_btfids: Alter how HOSTCC is forced")
Reported-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Acked-by: Ian Rogers <irogers@google.com>
Link: https://lore.kernel.org/bpf/20230202112839.1131892-1-jolsa@kernel.org
|
|
A passthrough decoder is a decoder that maps only 1 target. It is a
special case because it does not impose any constraints on the
interleave-math as compared to a decoder with multiple targets. Extend
the passthrough case to multi-target-capable decoders that only have one
target selected. I.e. the current code was only considering passthrough
*ports* which are only a subset of the potential passthrough decoder
scenarios.
Fixes: e4f6dfa9ef75 ("cxl/region: Fix 'distance' calculation with passthrough ports")
Cc: <stable@vger.kernel.org>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/167564540422.847146.13816934143225777888.stgit@dwillia2-xfh.jf.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Eric Dumazet says:
====================
net: core: use a dedicated kmem_cache for skb head allocs
Our profile data show that using kmalloc(non_const_size)/kfree(ptr)
has a certain cost, because kfree(ptr) has to pull a 'struct page'
in cpu caches.
Using a dedicated kmem_cache for TCP skb->head allocations makes
a difference, both in cpu cycles and memory savings.
This kmem_cache could also be used for GRO skb allocations,
this is left as a future exercise.
====================
Link: https://lore.kernel.org/r/20230206173103.2617121-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Recent removal of ksize() in alloc_skb() increased
performance because we no longer read
the associated struct page.
We have an equivalent cost at kfree_skb() time.
kfree(skb->head) has to access a struct page,
often cold in cpu caches to get the owning
struct kmem_cache.
Considering that many allocations are small (at least for TCP ones)
we can have our own kmem_cache to avoid the cache line miss.
This also saves memory because these small heads
are no longer padded to 1024 bytes.
CONFIG_SLUB=y
$ grep skbuff_small_head /proc/slabinfo
skbuff_small_head 2907 2907 640 51 8 : tunables 0 0 0 : slabdata 57 57 0
CONFIG_SLAB=y
$ grep skbuff_small_head /proc/slabinfo
skbuff_small_head 607 624 640 6 1 : tunables 54 27 8 : slabdata 104 104 5
Notes:
- After Kees Cook patches and this one, we might
be able to revert commit
dbae2b062824 ("net: skb: introduce and use a single page frag cache")
because GRO_MAX_HEAD is also small.
- This patch is a NOP for CONFIG_SLOB=y builds.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
All kmalloc_reserve() callers have to make the same computation,
we can factorize them, to prepare following patch in the series.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This is a cleanup patch, to prepare following change.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We have many places using this expression:
SKB_DATA_ALIGN(sizeof(struct skb_shared_info))
Use of SKB_HEAD_ALIGN() will allow to clean them.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v6.2
A few more fixes for v6.2, all driver specific and small. It's larger
than is ideal but we can't really control when people find problems.
|
|
MDS expects the completed cap release prior to responding to the
session flush for cache drop.
Cc: stable@vger.kernel.org
Link: http://tracker.ceph.com/issues/38009
Signed-off-by: Xiubo Li <xiubli@redhat.com>
Reviewed-by: Venky Shankar <vshankar@redhat.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull tracing fix from Steven Rostedt:
"Fix regression in poll() and select()
With the fix that made poll() and select() block if read would block
caused a slight regression in rasdaemon, as it needed that kind of
behavior. Add a way to make that behavior come back by writing zero
into the 'buffer_percentage', which means to never block on read"
* tag 'trace-v6.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
tracing: Fix poll() and select() do not work on per_cpu trace_pipe and trace_pipe_raw
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2023-02-06
this is a pull request of 47 patches for net-next/master.
The first two patch is by Oliver Hartkopp. One adds missing error
checking to the CAN_GW protocol, the other adds a missing CAN address
family check to the CAN ISO TP protocol.
Thomas Kopp contributes a performance optimization to the mcp251xfd
driver.
The next 11 patches are by Geert Uytterhoeven and add support for
R-Car V4H systems to the rcar_canfd driver.
Stephane Grosjean and Lukas Magel contribute 8 patches to the peak_usb
driver, which add support for configurable CAN channel ID.
The last 17 patches are by me and target the CAN bit timing
configuration. The bit timing is cleaned up, error messages are
improved and forwarded to user space via NL_SET_ERR_MSG_FMT() instead
of netdev_err(), and the SJW handling is updated, including the
definition of a new default value that will benefit CAN-FD
controllers, by increasing their oscillator tolerance.
* tag 'linux-can-next-for-6.3-20230206' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next: (47 commits)
can: bittiming: can_validate_bitrate(): report error via netlink
can: bittiming: can_calc_bittiming(): convert from netdev_err() to NL_SET_ERR_MSG_FMT()
can: bittiming: can_calc_bittiming(): clean up SJW handling
can: bittiming: can_sjw_set_default(): use Phase Seg2 / 2 as default for SJW
can: bittiming: can_sjw_check(): check that SJW is not longer than either Phase Buffer Segment
can: bittiming: can_sjw_check(): report error via netlink and harmonize error value
can: bittiming: can_fixup_bittiming(): report error via netlink and harmonize error value
can: bittiming: factor out can_sjw_set_default() and can_sjw_check()
can: bittiming: can_changelink() pass extack down callstack
can: netlink: can_changelink(): convert from netdev_err() to NL_SET_ERR_MSG_FMT()
can: netlink: can_validate(): validate sample point for CAN and CAN-FD
can: dev: register_candev(): bail out if both fixed bit rates and bit timing constants are provided
can: dev: register_candev(): ensure that bittiming const are valid
can: bittiming: can_get_bittiming(): use direct return and remove unneeded else
can: bittiming: can_fixup_bittiming(): set effective tq
can: bittiming: can_fixup_bittiming(): use CAN_SYNC_SEG instead of 1
can: bittiming(): replace open coded variants of can_bit_time()
can: peak_usb: Reorder include directives alphabetically
can: peak_usb: align CAN channel ID format in log with sysfs attribute
can: peak_usb: export PCAN CAN channel ID as sysfs device attribute
...
====================
Link: https://lore.kernel.org/r/20230206131620.2758724-1-mkl@pengutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
If ops->get_mm() returns a non-zero error code, we goto out_complete,
but there, we return 0. Fix that to propagate the "ret" variable to the
caller. If ops->get_mm() succeeds, it will always return 0.
Fixes: 2b30f8291a30 ("net: ethtool: add support for MAC Merge layer")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230206094932.446379-1-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When handling error path, ret needs to be set to correct value.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Fixes: d29d41e28eea ("ASoC: topology: Add support for multiple kcontrol types to a widget")
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230207210428.2076354-1-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The ISO 11783-5 standard, in "4.5.2 - Address claim requirements", states:
d) No CF shall begin, or resume, transmission on the network until 250
ms after it has successfully claimed an address except when
responding to a request for address-claimed.
But "Figure 6" and "Figure 7" in "4.5.4.2 - Address-claim
prioritization" show that the CF begins the transmission after 250 ms
from the first AC (address-claimed) message even if it sends another AC
message during that time window to resolve the address contention with
another CF.
As stated in "4.4.2.3 - Address-claimed message":
In order to successfully claim an address, the CF sending an address
claimed message shall not receive a contending claim from another CF
for at least 250 ms.
As stated in "4.4.3.2 - NAME management (NM) message":
1) A commanding CF can
d) request that a CF with a specified NAME transmit the address-
claimed message with its current NAME.
2) A target CF shall
d) send an address-claimed message in response to a request for a
matching NAME
Taking the above arguments into account, the 250 ms wait is requested
only during network initialization.
Do not restart the timer on AC message if both the NAME and the address
match and so if the address has already been claimed (timer has expired)
or the AC message has been sent to resolve the contention with another
CF (timer is still running).
Signed-off-by: Devid Antonio Filoni <devid.filoni@egluetechnologies.com>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/all/20221125170418.34575-1-devid.filoni@egluetechnologies.com
Fixes: 9d71dd0c7009 ("can: add support of SAE J1939 protocol")
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
snd_emux_xg_control() can be called with an argument 'param' greater
than size of 'control' array. It may lead to accessing 'control'
array at a wrong index.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Artemii Karasev <karasev@ispras.ru>
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230207132026.2870-1-karasev@ispras.ru
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Currently only the network namespace of devlink instance is monitored
for port events. If netdev is moved to a different namespace and then
unregistered, NETDEV_PRE_UNINIT is missed which leads to trigger
following WARN_ON in devl_port_unregister().
WARN_ON(devlink_port->type != DEVLINK_PORT_TYPE_NOTSET);
Fix this by changing the netdev notifier from per-net to global so no
event is missed.
Fixes: 02a68a47eade ("net: devlink: track netdev with devlink_port assigned")
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20230206094151.2557264-1-jiri@resnulli.us
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The version information is at the bit31 ~ bit16 in the VERID
register, so need to right shift 16bit to get it, otherwise
the result of comparison "sai->verid.version >= 0x0301" is
wrong.
Fixes: 99c1e74f25d4 ("ASoC: fsl_sai: store full version instead of major/minor")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/1675760664-25193-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
comprehensive
We have two IS1 filters of the OCELOT_VCAP_KEY_ANY key type (the one with
"action vlan pop" and the one with "action vlan modify") and one of the
OCELOT_VCAP_KEY_IPV4 key type (the one with "action skbedit priority").
But we have no IS1 filter with the OCELOT_VCAP_KEY_ETYPE key type, and
there was an uncaught breakage there.
To increase test coverage, convert one of the OCELOT_VCAP_KEY_ANY
filters to OCELOT_VCAP_KEY_ETYPE, by making the filter also match on the
MAC SA of the traffic sent by mausezahn, $h1_mac.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20230205192409.1796428-2-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Alternative short title: don't instruct the hardware to match on
EtherType with "protocol 802.1Q" flower filters. It doesn't work for the
reasons detailed below.
With a command such as the following:
tc filter add dev $swp1 ingress chain $(IS1 2) pref 3 \
protocol 802.1Q flower skip_sw vlan_id 200 src_mac $h1_mac \
action vlan modify id 300 \
action goto chain $(IS2 0 0)
the created filter is set by ocelot_flower_parse_key() to be of type
OCELOT_VCAP_KEY_ETYPE, and etype is set to {value=0x8100, mask=0xffff}.
This gets propagated all the way to is1_entry_set() which commits it to
hardware (the VCAP_IS1_HK_ETYPE field of the key). Compare this to the
case where src_mac isn't specified - the key type is OCELOT_VCAP_KEY_ANY,
and is1_entry_set() doesn't populate VCAP_IS1_HK_ETYPE.
The problem is that for VLAN-tagged frames, the hardware interprets the
ETYPE field as holding the encapsulated VLAN protocol. So the above
filter will only match those packets which have an encapsulated protocol
of 0x8100, rather than all packets with VLAN ID 200 and the given src_mac.
The reason why this is allowed to occur is because, although we have a
block of code in ocelot_flower_parse_key() which sets "match_protocol"
to false when VLAN keys are present, that code executes too late.
There is another block of code, which executes for Ethernet addresses,
and has a "goto finished_key_parsing" and skips the VLAN header parsing.
By skipping it, "match_protocol" remains with the value it was
initialized with, i.e. "true", and "proto" is set to f->common.protocol,
or 0x8100.
The concept of ignoring some keys rather than erroring out when they are
present but can't be offloaded is dubious in itself, but is present
since the initial commit fe3490e6107e ("net: mscc: ocelot: Hardware
ofload for tc flower filter"), and it's outside of the scope of this
patch to change that.
The problem was introduced when the driver started to interpret the
flower filter's protocol, and populate the VCAP filter's ETYPE field
based on it.
To fix this, it is sufficient to move the code that parses the VLAN keys
earlier than the "goto finished_key_parsing" instruction. This will
ensure that if we have a flower filter with both VLAN and Ethernet
address keys, it won't match on ETYPE 0x8100, because the VLAN key
parsing sets "match_protocol = false".
Fixes: 86b956de119c ("net: mscc: ocelot: support matching on EtherType")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230205192409.1796428-1-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
memblock_free_late()."
This reverts commit 115d9d77bb0f9152c60b6e8646369fa7f6167593.
The pages being freed by memblock_free_late() have already been
initialized, but if they are in the deferred init range,
__free_one_page() might access nearby uninitialized pages when trying to
coalesce buddies. This can, for example, trigger this BUG:
BUG: unable to handle page fault for address: ffffe964c02580c8
RIP: 0010:__list_del_entry_valid+0x3f/0x70
<TASK>
__free_one_page+0x139/0x410
__free_pages_ok+0x21d/0x450
memblock_free_late+0x8c/0xb9
efi_free_boot_services+0x16b/0x25c
efi_enter_virtual_mode+0x403/0x446
start_kernel+0x678/0x714
secondary_startup_64_no_verify+0xd2/0xdb
</TASK>
A proper fix will be more involved so revert this change for the time
being.
Fixes: 115d9d77bb0f ("mm: Always release pages to the buddy allocator in memblock_free_late().")
Signed-off-by: Aaron Thompson <dev@aaront.org>
Link: https://lore.kernel.org/r/20230207082151.1303-1-dev@aaront.org
Signed-off-by: Mike Rapoport (IBM) <rppt@kernel.org>
|
|
Frank reports that in a mt7530 setup where some ports are standalone and
some are in a VLAN-aware bridge, 8021q uppers of the standalone ports
lose their VLAN tag on xmit, as seen by the link partner.
This seems to occur because once the other ports join the VLAN-aware
bridge, mt7530_port_vlan_filtering() also calls
mt7530_port_set_vlan_aware(ds, cpu_dp->index), and this affects the way
that the switch processes the traffic of the standalone port.
Relevant is the PVC_EG_TAG bit. The MT7530 documentation says about it:
EG_TAG: Incoming Port Egress Tag VLAN Attribution
0: disabled (system default)
1: consistent (keep the original ingress tag attribute)
My interpretation is that this setting applies on the ingress port, and
"disabled" is basically the normal behavior, where the egress tag format
of the packet (tagged or untagged) is decided by the VLAN table
(MT7530_VLAN_EGRESS_UNTAG or MT7530_VLAN_EGRESS_TAG).
But there is also an option of overriding the system default behavior,
and for the egress tagging format of packets to be decided not by the
VLAN table, but simply by copying the ingress tag format (if ingress was
tagged, egress is tagged; if ingress was untagged, egress is untagged;
aka "consistent). This is useful in 2 scenarios:
- VLAN-unaware bridge ports will always encounter a miss in the VLAN
table. They should forward a packet as-is, though. So we use
"consistent" there. See commit e045124e9399 ("net: dsa: mt7530: fix
tagged frames pass-through in VLAN-unaware mode").
- Traffic injected from the CPU port. The operating system is in god
mode; if it wants a packet to exit as VLAN-tagged, it sends it as
VLAN-tagged. Otherwise it sends it as VLAN-untagged*.
*This is true only if we don't consider the bridge TX forwarding offload
feature, which mt7530 doesn't support.
So for now, make the CPU port always stay in "consistent" mode to allow
software VLANs to be forwarded to their egress ports with the VLAN tag
intact, and not stripped.
Link: https://lore.kernel.org/netdev/trinity-e6294d28-636c-4c40-bb8b-b523521b00be-1674233135062@3c-app-gmx-bs36/
Fixes: e045124e9399 ("net: dsa: mt7530: fix tagged frames pass-through in VLAN-unaware mode")
Reported-by: Frank Wunderlich <frank-w@public-files.de>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230205140713.1609281-1-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
As the mention in commmit f7452a7e96c1 ("RDMA/rtrs-srv: fix memory leak by missing kobject free"),
it was intended to remove the kobject_del for srv_path->kobj.
f7452a7e96c1 said:
>This patch moves kobject_del() into free_sess() so that the kobject of
> rtrs_srv_sess can be freed.
This patch also move rtrs_srv_destroy_once_sysfs_root_folders back to
'if (srv_path->kobj.state_in_sysfs)' block to avoid a 'held lock freed!'
A kernel panic will be triggered by following script
-----------------------
$ while true
do
echo "sessname=foo path=ip:<ip address> device_path=/dev/nvme0n1" > /sys/devices/virtual/rnbd-client/ctl/map_device
echo "normal" > /sys/block/rnbd0/rnbd/unmap_device
done
-----------------------
The bisection pointed to commit 6af4609c18b3 ("RDMA/rtrs-srv: Fix several issues in rtrs_srv_destroy_path_files")
at last.
rnbd_server L777: </dev/nvme0n1@foo>: Opened device 'nvme0n1'
general protection fault, probably for non-canonical address 0x765f766564753aea: 0000 [#1] PREEMPT SMP PTI
CPU: 0 PID: 3558 Comm: systemd-udevd Kdump: loaded Not tainted 6.1.0-rc3-roce-flush+ #51
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014
RIP: 0010:kernfs_dop_revalidate+0x36/0x180
Code: 00 00 41 55 41 54 55 53 48 8b 47 68 48 89 fb 48 85 c0 0f 84 db 00 00 00 48 8b a8 60 04 00 00 48 8b 45 30 48 85 c0 48 0f 44 c5 <4c> 8b 60 78 49 81 c4 d8 00 00 00 4c 89 e7 e8 b7 78 7b 00 8b 05 3d
RSP: 0018:ffffaf1700b67c78 EFLAGS: 00010206
RAX: 765f766564753a72 RBX: ffff89e2830849c0 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff89e2830849c0
RBP: ffff89e280361bd0 R08: 0000000000000000 R09: 0000000000000001
R10: 0000000000000065 R11: 0000000000000000 R12: ffff89e2830849c0
R13: ffff89e283084888 R14: d0d0d0d0d0d0d0d0 R15: 2f2f2f2f2f2f2f2f
FS: 00007f13fbce7b40(0000) GS:ffff89e2bbc00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f93e055d340 CR3: 0000000104664002 CR4: 00000000001706f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
lookup_fast+0x7b/0x100
walk_component+0x21/0x160
link_path_walk.part.0+0x24d/0x390
path_openat+0xad/0x9a0
do_filp_open+0xa9/0x150
? lock_release+0x13c/0x2e0
? _raw_spin_unlock+0x29/0x50
? alloc_fd+0x124/0x1f0
do_sys_openat2+0x9b/0x160
__x64_sys_openat+0x54/0xa0
do_syscall_64+0x3b/0x90
entry_SYSCALL_64_after_hwframe+0x63/0xcd
RIP: 0033:0x7f13fc9d701b
Code: 25 00 00 41 00 3d 00 00 41 00 74 4b 64 8b 04 25 18 00 00 00 85 c0 75 67 44 89 e2 48 89 ee bf 9c ff ff ff b8 01 01 00 00 0f 05 <48> 3d 00 f0 ff ff 0f 87 91 00 00 00 48 8b 54 24 28 64 48 2b 14 25
RSP: 002b:00007ffddf242640 EFLAGS: 00000246 ORIG_RAX: 0000000000000101
RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f13fc9d701b
RDX: 0000000000080000 RSI: 00007ffddf2427c0 RDI: 00000000ffffff9c
RBP: 00007ffddf2427c0 R08: 00007f13fcc5b440 R09: 21b2131aa64b1ef2
R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000080000
R13: 00007ffddf2427c0 R14: 000055ed13be8db0 R15: 0000000000000000
Fixes: 6af4609c18b3 ("RDMA/rtrs-srv: Fix several issues in rtrs_srv_destroy_path_files")
Acked-by: Guoqing Jiang <guoqing.jiang@linux.dev>
Signed-off-by: Li Zhijian <lizhijian@fujitsu.com>
Link: https://lore.kernel.org/r/1675332721-2-1-git-send-email-lizhijian@fujitsu.com
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
There is a HP platform needs ALC236_FIXUP_HP_GPIO_LED quirk to
make mic-mute/audio-mute working.
Signed-off-by: Andy Chi <andy.chi@canonical.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230207083011.100189-1-andy.chi@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
If the firmware mangled the register contents too much,
check the saved value for the Direct IRQ mode. If it
matches, we will restore the pin state.
Reported-by: Jim Minter <jimminter@microsoft.com>
Fixes: 6989ea4881c8 ("pinctrl: intel: Save and restore pins in "direct IRQ" mode")
Tested-by: Jim Minter <jimminter@microsoft.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20230206141558.20916-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
We reference dump buffers both by their handle as well as their
object. The problem is now that when anybody iterates over the DRM
framebuffers and exports the underlying GEM objects through DMA-buf
we run into a circular reference count situation.
The result is that the fbdev handling holds the GEM handle preventing
the DMA-buf in the GEM object to be released. This DMA-buf in turn
holds a reference to the driver module which on unload would release
the fbdev.
Break that loop by releasing the handle as soon as the DRM
framebuffer object is created. The DRM framebuffer and the DRM client
buffer structure still hold a reference to the underlying GEM object
preventing its destruction.
Signed-off-by: Christian König <christian.koenig@amd.com>
Fixes: c76f0f7cb546 ("drm: Begin an API for in-kernel clients")
Cc: <stable@vger.kernel.org>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Tested-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230126102814.8722-1-christian.koenig@amd.com
|
|
Use actual CPU number instead of hardcoded value to decide the size
of 'cpu_used_mask' in 'struct sw_flow'. Below is the reason.
'struct cpumask cpu_used_mask' is embedded in struct sw_flow.
Its size is hardcoded to CONFIG_NR_CPUS bits, which can be
8192 by default, it costs memory and slows down ovs_flow_alloc.
To address this:
Redefine cpu_used_mask to pointer.
Append cpumask_size() bytes after 'stat' to hold cpumask.
Initialization cpu_used_mask right after stats_last_writer.
APIs like cpumask_next and cpumask_set_cpu never access bits
beyond cpu count, cpumask_size() bytes of memory is enough.
Signed-off-by: Eddy Tao <taoyuan_eddy@hotmail.com>
Acked-by: Eelco Chaudron <echaudro@redhat.com>
Link: https://lore.kernel.org/r/OS3P286MB229570CCED618B20355D227AF5D59@OS3P286MB2295.JPNP286.PROD.OUTLOOK.COM
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The forward declaration was introduced with a prototype that does
not match the function definition:
drivers/net/ethernet/amd/xgbe/xgbe-phy-v2.c:2166:13: error: conflicting types for 'xgbe_phy_perform_ratechange' due to enum/integer mismatch; have 'void(struct xgbe_prv_data *, enum xgbe_mb_cmd, enum xgbe_mb_subcmd)' [-Werror=enum-int-mismatch]
2166 | static void xgbe_phy_perform_ratechange(struct xgbe_prv_data *pdata,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/amd/xgbe/xgbe-phy-v2.c:391:13: note: previous declaration of 'xgbe_phy_perform_ratechange' with type 'void(struct xgbe_prv_data *, unsigned int, unsigned int)'
391 | static void xgbe_phy_perform_ratechange(struct xgbe_prv_data *pdata,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~
Ideally there should not be any forward declarations here, which
would make it easier to show that there is no unbounded recursion.
I tried fixing this but could not figure out how to avoid the
recursive call.
As a hotfix, address only the broken prototype to fix the build
problem instead.
Fixes: 4f3b20bfbb75 ("amd-xgbe: add support for rx-adaptation")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Link: https://lore.kernel.org/r/20230203121553.2871598-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There are no external users of the vsc7514_*_regmap[] symbols or
vsc7514_vcap_* functions. They were exported in commit 32ecd22ba60b ("net:
mscc: ocelot: split register definitions to a separate file") with the
intention of being used, but the actual structure used in commit
2efaca411c96 ("net: mscc: ocelot: expose vsc7514_regmap definition") ended
up being all that was needed.
Bury these unnecessary symbols.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Suggested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230204182056.25502-1-colin.foster@in-advantage.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Ajit Khaparde says:
====================
bnxt: Add Auxiliary driver support
Add auxiliary device driver for Broadcom devices.
The bnxt_en driver will register and initialize an aux device
if RDMA is enabled in the underlying device.
The bnxt_re driver will then probe and initialize the
RoCE interfaces with the infiniband stack.
We got rid of the bnxt_en_ops which the bnxt_re driver used to
communicate with bnxt_en.
Similarly We have tried to clean up most of the bnxt_ulp_ops.
In most of the cases we used the functions and entry points provided
by the auxiliary bus driver framework.
And now these are the minimal functions needed to support the functionality.
We will try to work on getting rid of the remaining if we find any
other viable option in future.
* 'aux-bus-v11' of https://github.com/ajitkhaparde1/linux:
bnxt_en: Remove runtime interrupt vector allocation
RDMA/bnxt_re: Remove the sriov config callback
bnxt_en: Remove struct bnxt access from RoCE driver
bnxt_en: Use auxiliary bus calls over proprietary calls
bnxt_en: Use direct API instead of indirection
bnxt_en: Remove usage of ulp_id
RDMA/bnxt_re: Use auxiliary driver interface
bnxt_en: Add auxiliary driver support
====================
Link: https://lore.kernel.org/r/20230202033809.3989-1-ajit.khaparde@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When the network status is unstable, use-after-free may occur when
read data from the server.
BUG: KASAN: use-after-free in readpages_fill_pages+0x14c/0x7e0
Call Trace:
<TASK>
dump_stack_lvl+0x38/0x4c
print_report+0x16f/0x4a6
kasan_report+0xb7/0x130
readpages_fill_pages+0x14c/0x7e0
cifs_readv_receive+0x46d/0xa40
cifs_demultiplex_thread+0x121c/0x1490
kthread+0x16b/0x1a0
ret_from_fork+0x2c/0x50
</TASK>
Allocated by task 2535:
kasan_save_stack+0x22/0x50
kasan_set_track+0x25/0x30
__kasan_kmalloc+0x82/0x90
cifs_readdata_direct_alloc+0x2c/0x110
cifs_readdata_alloc+0x2d/0x60
cifs_readahead+0x393/0xfe0
read_pages+0x12f/0x470
page_cache_ra_unbounded+0x1b1/0x240
filemap_get_pages+0x1c8/0x9a0
filemap_read+0x1c0/0x540
cifs_strict_readv+0x21b/0x240
vfs_read+0x395/0x4b0
ksys_read+0xb8/0x150
do_syscall_64+0x3f/0x90
entry_SYSCALL_64_after_hwframe+0x72/0xdc
Freed by task 79:
kasan_save_stack+0x22/0x50
kasan_set_track+0x25/0x30
kasan_save_free_info+0x2e/0x50
__kasan_slab_free+0x10e/0x1a0
__kmem_cache_free+0x7a/0x1a0
cifs_readdata_release+0x49/0x60
process_one_work+0x46c/0x760
worker_thread+0x2a4/0x6f0
kthread+0x16b/0x1a0
ret_from_fork+0x2c/0x50
Last potentially related work creation:
kasan_save_stack+0x22/0x50
__kasan_record_aux_stack+0x95/0xb0
insert_work+0x2b/0x130
__queue_work+0x1fe/0x660
queue_work_on+0x4b/0x60
smb2_readv_callback+0x396/0x800
cifs_abort_connection+0x474/0x6a0
cifs_reconnect+0x5cb/0xa50
cifs_readv_from_socket.cold+0x22/0x6c
cifs_read_page_from_socket+0xc1/0x100
readpages_fill_pages.cold+0x2f/0x46
cifs_readv_receive+0x46d/0xa40
cifs_demultiplex_thread+0x121c/0x1490
kthread+0x16b/0x1a0
ret_from_fork+0x2c/0x50
The following function calls will cause UAF of the rdata pointer.
readpages_fill_pages
cifs_read_page_from_socket
cifs_readv_from_socket
cifs_reconnect
__cifs_reconnect
cifs_abort_connection
mid->callback() --> smb2_readv_callback
queue_work(&rdata->work) # if the worker completes first,
# the rdata is freed
cifs_readv_complete
kref_put
cifs_readdata_release
kfree(rdata)
return rdata->... # UAF in readpages_fill_pages()
Similarly, this problem also occurs in the uncache_fill_pages().
Fix this by adjusts the order of condition judgment in the return
statement.
Signed-off-by: ZhaoLong Wang <wangzhaolong1@huawei.com>
Cc: stable@vger.kernel.org
Acked-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
Not all decoders have a reset callback.
The CXL specification allows a host bridge with a single root port to
have no explicit HDM decoders. Currently the region driver assumes there
are none. As such the CXL core creates a special pass through decoder
instance without a commit/reset callback.
Prior to this patch, the ->reset() callback was called unconditionally when
calling cxl_region_decode_reset. Thus a configuration with 1 Host Bridge,
1 Root Port, and one directly attached CXL type 3 device or multiple CXL
type 3 devices attached to downstream ports of a switch can cause a null
pointer dereference.
Before the fix, a kernel crash was observed when we destroy the region, and
a pass through decoder is reset.
The issue can be reproduced as below,
1) create a region with a CXL setup which includes a HB with a
single root port under which a memdev is attached directly.
2) destroy the region with cxl destroy-region regionX -f.
Fixes: 176baefb2eb5 ("cxl/hdm: Commit decoder state to hardware")
Cc: <stable@vger.kernel.org>
Signed-off-by: Fan Ni <fan.ni@samsung.com>
Reviewed-by: Davidlohr Bueso <dave@stgolabs.net>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Tested-by: Gregory Price <gregory.price@memverge.com>
Reviewed-by: Gregory Price <gregory.price@memverge.com>
Link: https://lore.kernel.org/r/20221215170909.2650271-1-fan.ni@samsung.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
The RFI and STF security mitigation options can flip the
interrupt_exit_not_reentrant static branch condition concurrently with
the interrupt exit code which tests that branch.
Interrupt exit tests this condition to set MSR[EE|RI] for exit, then
again in the case a soft-masked interrupt is found pending, to recover
the MSR so the interrupt can be replayed before attempting to exit
again. If the condition changes between these two tests, the MSR and irq
soft-mask state will become corrupted, leading to warnings and possible
crashes. For example, if the branch is initially true then false,
MSR[EE] will be 0 but PACA_IRQ_HARD_DIS clear and EE may not get
enabled, leading to warnings in irq_64.c.
Fixes: 13799748b957 ("powerpc/64: use interrupt restart table to speed up return from interrupt")
Cc: stable@vger.kernel.org # v5.14+
Reported-by: Sachin Sant <sachinp@linux.ibm.com>
Tested-by: Sachin Sant <sachinp@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20230206042240.92103-1-npiggin@gmail.com
|
|
When ice_add_special_words() fails, the 'rm' is not released, which will
lead to a memory leak. Fix this up by going to 'err_unroll' label.
Compile tested only.
Fixes: 8b032a55c1bd ("ice: low level support for tunnels")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
|
|
The > comparison should be >= to prevent reading one element beyond
the end of the array.
The "vsi->num_rxq" is not strictly speaking the number of elements in
the vsi->rxq_map[] array. The array has "vsi->alloc_rxq" elements and
"vsi->num_rxq" is less than or equal to the number of elements in the
array. The array is allocated in ice_vsi_alloc_arrays(). It's still
an off by one but it might not access outside the end of the array.
Fixes: 143b86f346c7 ("ice: Enable RX queue selection using skbedit action")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Amritha Nambiar <amritha.nambiar@intel.com>
Tested-by: Bharathi Sreenivas <bharathi.sreenivas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
|
|
If the user turns on the vf-true-promiscuous-support flag, then Rx VLAN
filtering will be disabled if the VF requests to enable promiscuous
mode. When the VF is in a port VLAN, this is the incorrect behavior
because it will allow the VF to receive traffic outside of its port VLAN
domain. Fortunately this only resulted in the VF(s) receiving broadcast
traffic outside of the VLAN domain because all of the VLAN promiscuous
rules are based on the port VLAN ID. Fix this by setting the
.disable_rx_filtering VLAN op to a no-op when a port VLAN is enabled on
the VF.
Also, make sure to make this fix for both Single VLAN Mode and Double
VLAN Mode enabled devices.
Fixes: c31af68a1b94 ("ice: Add outer_vlan_ops and VSI specific VLAN ops implementations")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Karen Ostrowska <karen.ostrowska@intel.com>
Tested-by: Marek Szlosek <marek.szlosek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
KASAN reported:
[ 9793.708867] BUG: KASAN: global-out-of-bounds in ice_get_link_speed+0x16/0x30 [ice]
[ 9793.709205] Read of size 4 at addr ffffffffc1271b1c by task kworker/6:1/402
[ 9793.709222] CPU: 6 PID: 402 Comm: kworker/6:1 Kdump: loaded Tainted: G B OE 6.1.0+ #3
[ 9793.709235] Hardware name: Intel Corporation S2600WFT/S2600WFT, BIOS SE5C620.86B.00.01.0014.070920180847 07/09/2018
[ 9793.709245] Workqueue: ice ice_service_task [ice]
[ 9793.709575] Call Trace:
[ 9793.709582] <TASK>
[ 9793.709588] dump_stack_lvl+0x44/0x5c
[ 9793.709613] print_report+0x17f/0x47b
[ 9793.709632] ? __cpuidle_text_end+0x5/0x5
[ 9793.709653] ? ice_get_link_speed+0x16/0x30 [ice]
[ 9793.709986] ? ice_get_link_speed+0x16/0x30 [ice]
[ 9793.710317] kasan_report+0xb7/0x140
[ 9793.710335] ? ice_get_link_speed+0x16/0x30 [ice]
[ 9793.710673] ice_get_link_speed+0x16/0x30 [ice]
[ 9793.711006] ice_vc_notify_vf_link_state+0x14c/0x160 [ice]
[ 9793.711351] ? ice_vc_repr_cfg_promiscuous_mode+0x120/0x120 [ice]
[ 9793.711698] ice_vc_process_vf_msg+0x7a7/0xc00 [ice]
[ 9793.712074] __ice_clean_ctrlq+0x98f/0xd20 [ice]
[ 9793.712534] ? ice_bridge_setlink+0x410/0x410 [ice]
[ 9793.712979] ? __request_module+0x320/0x520
[ 9793.713014] ? ice_process_vflr_event+0x27/0x130 [ice]
[ 9793.713489] ice_service_task+0x11cf/0x1950 [ice]
[ 9793.713948] ? io_schedule_timeout+0xb0/0xb0
[ 9793.713972] process_one_work+0x3d0/0x6a0
[ 9793.714003] worker_thread+0x8a/0x610
[ 9793.714031] ? process_one_work+0x6a0/0x6a0
[ 9793.714049] kthread+0x164/0x1a0
[ 9793.714071] ? kthread_complete_and_exit+0x20/0x20
[ 9793.714100] ret_from_fork+0x1f/0x30
[ 9793.714137] </TASK>
[ 9793.714151] The buggy address belongs to the variable:
[ 9793.714158] ice_aq_to_link_speed+0x3c/0xffffffffffff3520 [ice]
[ 9793.714632] Memory state around the buggy address:
[ 9793.714642] ffffffffc1271a00: f9 f9 f9 f9 00 00 05 f9 f9 f9 f9 f9 00 00 02 f9
[ 9793.714656] ffffffffc1271a80: f9 f9 f9 f9 00 00 04 f9 f9 f9 f9 f9 00 00 00 00
[ 9793.714670] >ffffffffc1271b00: 00 00 00 04 f9 f9 f9 f9 04 f9 f9 f9 f9 f9 f9 f9
[ 9793.714680] ^
[ 9793.714690] ffffffffc1271b80: 00 00 00 00 00 04 f9 f9 f9 f9 f9 f9 00 00 00 00
[ 9793.714704] ffffffffc1271c00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
The ICE_AQ_LINK_SPEED_UNKNOWN define is BIT(15). The value is bigger
than both legacy and normal link speed tables. Add one element (0 -
unknown) to both tables. There is no need to explicitly set table size,
leave it empty.
Fixes: 1d0e28a9be1f ("ice: Remove and replace ice speed defines with ethtool.h versions")
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
|
