| Age | Commit message (Collapse) | Author |
|---|
|
The "follow" fail_over_mac policy is useful for multiport devices that
either become confused or incur a performance penalty when multiple
ports are programmed with the same MAC address, but the same MAC
address still may happened by this steps for this policy:
1) echo +eth0 > /sys/class/net/bond0/bonding/slaves
bond0 has the same mac address with eth0, it is MAC1.
2) echo +eth1 > /sys/class/net/bond0/bonding/slaves
eth1 is backup, eth1 has MAC2.
3) ifconfig eth0 down
eth1 became active slave, bond will swap MAC for eth0 and eth1,
so eth1 has MAC1, and eth0 has MAC2.
4) ifconfig eth1 down
there is no active slave, and eth1 still has MAC1, eth2 has MAC2.
5) ifconfig eth0 up
the eth0 became active slave again, the bond set eth0 to MAC1.
Something wrong here, then if you set eth1 up, the eth0 and eth1 will have the same
MAC address, it will break this policy for ACTIVE_BACKUP mode.
This patch will fix this problem by finding the old active slave and
swap them MAC address before change active slave.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Tested-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2015-07-16
this is a pull request of 2 patches by Stefan Agner. He fixes the resume
operation in the mcp251x driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch reverts 19424e052fb44da2f00d1a868cbb51f3e9f4bbb5 ("sit:
Add gro callbacks to sit_offload") because it generates packets
that cannot be handled even by our own GSO.
Reported-by: Wolfgang Walter <linux@stwm.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
7445E0 contains an ECO which disconnected the internal SF2 pseudo-PHY which was
known to conflict with the external pseudo-PHY of BCM53125 switches. This
motivated the need to utilize the internal SF2 MDIO controller via indirect
register reads/writes to control external Broadcom switches due to this address
conflict (both responded at address 30d).
For 7445E0, the internal pseudo-PHY of the SF2 switch got disconnected, and as
a consequence this prevents the internal SF2 MDIO bus controller from reading
data (reads back everything as 0) since the MDI line is tied low.
Fix this by making the indirect register reads and writes conditional to
7445D0, on 7445E0 we can utilize the SWITCH_MDIO controller (backed by
mdio-unimac and not the DSA created slave MII bus).
We utilize of_machine_is_compatible() here since this is the only way for use
to differentiate between these two chips in a way that does not violate layers
or becomes (too) vendor-specific.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the bond is enslaving a device with different type it will be setup
by it, but if after being setup the enslave fails the bond doesn't
switch back its type and also keeps pointers to foreign structures that can
be long gone. Thus revert back any type changes if the enslave failed and
the bond had to change its type.
Example:
Before patch:
$ echo lo > bond0/bonding/slaves
-bash: echo: write error: Cannot assign requested address
$ ip l sh bond0
20: bond0: <BROADCAST,MULTICAST,MASTER> mtu 1500 qdisc noop state DOWN
mode DEFAULT group default
link/loopback 16:54:78:34:bd:41 brd 00:00:00:00:00:00
$ echo +eth1 > bond0/bonding/slaves
$ ip l sh bond0
20: bond0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
DEFAULT group default qlen 1000
link/ether 52:54:00:3f:47:69 brd ff:ff:ff:ff:ff:ff
(notice the MASTER flag is gone)
After patch:
$ echo lo > bond0/bonding/slaves
-bash: echo: write error: Cannot assign requested address
$ ip l sh bond0
21: bond0: <BROADCAST,MULTICAST,MASTER> mtu 1500 qdisc noop state DOWN
mode DEFAULT group default qlen 1000
link/ether 6e:66:94:f6:07:fc brd ff:ff:ff:ff:ff:ff
$ echo +eth1 > bond0/bonding/slaves
$ ip l sh bond0
21: bond0: <BROADCAST,MULTICAST,MASTER> mtu 1500 qdisc noop state DOWN
mode DEFAULT group default qlen 1000
link/ether 52:54:00:3f:47:69 brd ff:ff:ff:ff:ff:ff
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Fixes: e36b9d16c6a6 ("bonding: clean muticast addresses when device changes type")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the bonding is being unloaded and the netdevice notifier is
unregistered it executes NETDEV_UNREGISTER for each device which should
remove the bond's proc entry but if the device enslaved is not of
ARPHRD_ETHER type and is in front of the bonding, it may execute
bond_release_and_destroy() first which would release the last slave and
destroy the bond device leaving the proc entry and thus we will get the
following error (with dynamic debug on for bond_netdev_event to see the
events order):
[ 908.963051] eql: event: 9
[ 908.963052] eql: IFF_SLAVE
[ 908.963054] eql: event: 2
[ 908.963056] eql: IFF_SLAVE
[ 908.963058] eql: event: 6
[ 908.963059] eql: IFF_SLAVE
[ 908.963110] bond0: Releasing active interface eql
[ 908.976168] bond0: Destroying bond bond0
[ 908.976266] bond0 (unregistering): Released all slaves
[ 908.984097] ------------[ cut here ]------------
[ 908.984107] WARNING: CPU: 0 PID: 1787 at fs/proc/generic.c:575
remove_proc_entry+0x112/0x160()
[ 908.984110] remove_proc_entry: removing non-empty directory
'net/bonding', leaking at least 'bond0'
[ 908.984111] Modules linked in: bonding(-) eql(O) 9p nfsd auth_rpcgss
oid_registry nfs_acl nfs lockd grace fscache sunrpc crct10dif_pclmul
crc32_pclmul crc32c_intel ghash_clmulni_intel ppdev qxl drm_kms_helper
snd_hda_codec_generic aesni_intel ttm aes_x86_64 glue_helper pcspkr lrw
gf128mul ablk_helper cryptd snd_hda_intel virtio_console snd_hda_codec
psmouse serio_raw snd_hwdep snd_hda_core 9pnet_virtio 9pnet evdev joydev
drm virtio_balloon snd_pcm snd_timer snd soundcore i2c_piix4 i2c_core
pvpanic acpi_cpufreq parport_pc parport processor thermal_sys button
autofs4 ext4 crc16 mbcache jbd2 hid_generic usbhid hid sg sr_mod cdrom
ata_generic virtio_blk virtio_net floppy ata_piix e1000 libata ehci_pci
virtio_pci scsi_mod uhci_hcd ehci_hcd virtio_ring virtio usbcore
usb_common [last unloaded: bonding]
[ 908.984168] CPU: 0 PID: 1787 Comm: rmmod Tainted: G W O
4.2.0-rc2+ #8
[ 908.984170] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
[ 908.984172] 0000000000000000 ffffffff81732d41 ffffffff81525b34
ffff8800358dfda8
[ 908.984175] ffffffff8106c521 ffff88003595af78 ffff88003595af40
ffff88003e3a4280
[ 908.984178] ffffffffa058d040 0000000000000000 ffffffff8106c59a
ffffffff8172ebd0
[ 908.984181] Call Trace:
[ 908.984188] [<ffffffff81525b34>] ? dump_stack+0x40/0x50
[ 908.984193] [<ffffffff8106c521>] ? warn_slowpath_common+0x81/0xb0
[ 908.984196] [<ffffffff8106c59a>] ? warn_slowpath_fmt+0x4a/0x50
[ 908.984199] [<ffffffff81218352>] ? remove_proc_entry+0x112/0x160
[ 908.984205] [<ffffffffa05850e6>] ? bond_destroy_proc_dir+0x26/0x30
[bonding]
[ 908.984208] [<ffffffffa057540e>] ? bond_net_exit+0x8e/0xa0 [bonding]
[ 908.984217] [<ffffffff8142f407>] ? ops_exit_list.isra.4+0x37/0x70
[ 908.984225] [<ffffffff8142f52d>] ?
unregister_pernet_operations+0x8d/0xd0
[ 908.984228] [<ffffffff8142f58d>] ?
unregister_pernet_subsys+0x1d/0x30
[ 908.984232] [<ffffffffa0585269>] ? bonding_exit+0x23/0xdba [bonding]
[ 908.984236] [<ffffffff810e28ba>] ? SyS_delete_module+0x18a/0x250
[ 908.984241] [<ffffffff81086f99>] ? task_work_run+0x89/0xc0
[ 908.984244] [<ffffffff8152b732>] ?
entry_SYSCALL_64_fastpath+0x16/0x75
[ 908.984247] ---[ end trace 7c006ed4abbef24b ]---
Thus remove the proc entry manually if bond_release_and_destroy() is
used. Because of the checks in bond_remove_proc_entry() it's not a
problem for a bond device to change namespaces (the bug fixed by the
Fixes commit) but since commit
f9399814927ad ("bonding: Don't allow bond devices to change network
namespaces.") that can't happen anyway.
Reported-by: Carol Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Fixes: a64d49c3dd50 ("bonding: Manage /proc/net/bonding/ entries from
the netdev events")
Tested-by: Carol L Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mv88e6xxx_priv_state structure contains an fid_mask, where 1 means
the FID is free to use, 0 means the FID is in use.
This patch fixes the bit clear in mv88e6xxx_leave_bridge() when
assigning a new FID to a port.
Example scenario: I have 7 ports, port 5 is CPU, port 6 is unused (no
PHY). After setting the ports 0, 1 and 2 in bridge br0, and ports 3 and
4 in bridge br1, I have the following fid_mask: 0b111110010110 (0xf96).
Indeed, br0 uses FID 0, and br1 uses FID 3.
After setting nomaster for port 0, I get the wrong fid_mask: 0b10 (0x2).
With this patch we correctly get 0b111110010100 (0xf94), meaning port 0
uses FID 1, br0 uses FID 0, and br1 uses FID 3.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ANY_LAYOUT is a compatibility feature. It's implied
for VERSION_1 devices, and non-transitional devices
might not offer it. Change code to behave accordingly.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fix from Martin Schwidefsky:
"Fast path fix for the thread_struct breakage"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390: adapt entry.S to the move of thread_struct
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/egtvedt/linux-avr32
Pull AVR32 update from Hans-Christian Egtvedt.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/egtvedt/linux-avr32:
AVR32/time: Migrate to new 'set-state' interface
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/horms/ipvs
Simon Horman says:
====================
IPVS Fixes for v4.2
please consider this fix for v4.2.
For reasons that are not clear to me it is a bumper crop.
It seems to me that they are all relevant to stable.
Please let me know if you need my help to get the fixes into stable.
* ipvs: fix ipv6 route unreach panic
This problem appears to be present since IPv6 support was added to
IPVS in v2.6.28.
* ipvs: skb_orphan in case of forwarding
This appears to resolve a problem resulting from a side effect of
41063e9dd119 ("ipv4: Early TCP socket demux.") which was included in v3.6.
* ipvs: do not use random local source address for tunnels
This appears to resolve a problem introduced by
026ace060dfe ("ipvs: optimize dst usage for real server") in v3.10.
* ipvs: fix crash if scheduler is changed
This appears to resolve a problem introduced by
ceec4c381681 ("ipvs: convert services to rcu") in v3.10.
Julian has provided backports of the fix:
* [PATCHv2 3.10.81] ipvs: fix crash if scheduler is changed
http://www.spinics.net/lists/lvs-devel/msg04008.html
* [PATCHv2 3.12.44,3.14.45,3.18.16,4.0.6] ipvs: fix crash if scheduler is changed
http://www.spinics.net/lists/lvs-devel/msg04007.html
Please let me know how you would like to handle guiding these
backports into stable.
* ipvs: fix crash with sync protocol v0 and FTP
This appears to resolve a problem introduced by
749c42b620a9 ("ipvs: reduce sync rate with time thresholds") in v3.5
====================
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Quoting Daniel Borkmann:
"When adding connection tracking template rules to a netns, f.e. to
configure netfilter zones, the kernel will endlessly busy-loop as soon
as we try to delete the given netns in case there's at least one
template present, which is problematic i.e. if there is such bravery that
the priviledged user inside the netns is assumed untrusted.
Minimal example:
ip netns add foo
ip netns exec foo iptables -t raw -A PREROUTING -d 1.2.3.4 -j CT --zone 1
ip netns del foo
What happens is that when nf_ct_iterate_cleanup() is being called from
nf_conntrack_cleanup_net_list() for a provided netns, we always end up
with a net->ct.count > 0 and thus jump back to i_see_dead_people. We
don't get a soft-lockup as we still have a schedule() point, but the
serving CPU spins on 100% from that point onwards.
Since templates are normally allocated with nf_conntrack_alloc(), we
also bump net->ct.count. The issue why they are not yet nf_ct_put() is
because the per netns .exit() handler from x_tables (which would eventually
invoke xt_CT's xt_ct_tg_destroy() that drops reference on info->ct) is
called in the dependency chain at a *later* point in time than the per
netns .exit() handler for the connection tracker.
This is clearly a chicken'n'egg problem: after the connection tracker
.exit() handler, we've teared down all the connection tracking
infrastructure already, so rightfully, xt_ct_tg_destroy() cannot be
invoked at a later point in time during the netns cleanup, as that would
lead to a use-after-free. At the same time, we cannot make x_tables depend
on the connection tracker module, so that the xt_ct_tg_destroy() would
be invoked earlier in the cleanup chain."
Daniel confirms this has to do with the order in which modules are loaded or
having compiled nf_conntrack as modules while x_tables built-in. So we have no
guarantees regarding the order in which netns callbacks are executed.
Fix this by allocating the templates through kmalloc() from the respective
SYNPROXY and CT targets, so they don't depend on the conntrack kmem cache.
Then, release then via nf_ct_tmpl_free() from destroy_conntrack(). This branch
is marked as unlikely since conntrack templates are rarely allocated and only
from the configuration plane path.
Note that templates are not kept in any list to avoid further dependencies with
nf_conntrack anymore, thus, the tmpl larval list is removed.
Reported-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Tested-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
git commit 0c8c0f03e3a292e031596484275c14cf39c0ab7a
"x86/fpu, sched: Dynamically allocate 'struct fpu'"
moved the thread_struct to the end of the task_struct.
This causes some of the offsets used in entry.S to overflow their
instruction operand field. To fix this use aghi to create a
dedicated pointer for the thread_struct.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Migrate avr32 driver to the new 'set-state' interface provided by
clockevents core, the earlier 'set-mode' interface is marked obsolete
now.
This also enables us to implement callbacks for new states of clockevent
devices, for example: ONESHOT_STOPPED.
We want to call cpu_idle_poll_ctrl() in shutdown only if we were in
oneshot or resume state earlier. Create another variable to save this
information and check that in shutdown callback.
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
|
|
The param_val variable is what determines if schmitt
trigger is enabled on a pin or not. A typo here mean
that schmitt trigger was always enabled for standard
and i2c pins.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
imx1_pinconf_set assumes that the array of pins in struct
imx1_pinctrl_soc_info can be indexed by pin id to get the
pinctrl_pin_desc for a pin. This used to be correct up to commit
607af165c047 which removed some entries from the array and so made it
wrong to access the array by pin id.
The result of this bug is a wrong pin name in the output for small pin
ids and an oops for the bigger ones.
This patch is the result of a discussion that includes patches by Markus
Pargmann and Chris Ruehl.
Fixes: 607af165c047 ("pinctrl: i.MX27: Remove nonexistent pad definitions")
Cc: stable@vger.kernel.org
Reported-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
It's possible to hit a race condition if interrupts are generated on a GPIO
pin when the IRQ line in question is being disabled.
If the interrupt is freed, bcm2835_gpio_irq_disable() is called which
disables the event generation sources (edge, level). If an event occurred
between the last disabling of hard IRQs and the write to the event
source registers, a bit would be set in the GPIO event detect register
(GPEDSn) which goes unacknowledged by bcm2835_gpio_irq_handler()
so Linux complains loudly.
There is no per-GPIO mask register, so when disabling GPIO interrupts
write 1 to the relevant bit in GPEDSn to clear out any stale events.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The PSC IRQ is requested using request_irq() API and as result it can
be forced to be threaded IRQ in RT-Kernel if PCS_QUIRK_HAS_SHARED_IRQ
is enabled for pinctrl domain.
As result, following 'possible irq lock inversion dependency' report
can be seen:
=========================================================
[ INFO: possible irq lock inversion dependency detected ]
3.14.43-rt42-00360-g96ff499-dirty #24 Not tainted
---------------------------------------------------------
irq/369-pinctrl/927 just changed the state of lock:
(&pcs->lock){+.....}, at: [<c0375b54>] pcs_irq_handle+0x48/0x9c
but this lock was taken by another, HARDIRQ-safe lock in the past:
(&irq_desc_lock_class){-.....}
and interrupts could create inverse lock ordering between them.
other info that might help us debug this:
Possible interrupt unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&pcs->lock);
local_irq_disable();
lock(&irq_desc_lock_class);
lock(&pcs->lock);
<Interrupt>
lock(&irq_desc_lock_class);
*** DEADLOCK ***
no locks held by irq/369-pinctrl/927.
the shortest dependencies between 2nd lock and 1st lock:
-> (&irq_desc_lock_class){-.....} ops: 58724 {
IN-HARDIRQ-W at:
[<c0090040>] lock_acquire+0x9c/0x158
[<c07065c8>] _raw_spin_lock+0x48/0x58
[<c009edac>] handle_fasteoi_irq+0x24/0x15c
[<c009abb0>] generic_handle_irq+0x3c/0x4c
[<c000f83c>] handle_IRQ+0x50/0xa0
[<c0008674>] gic_handle_irq+0x3c/0x6c
[<c0707a04>] __irq_svc+0x44/0x8c
[<c000fc44>] arch_cpu_idle+0x40/0x4c
[<c009aadc>] cpu_startup_entry+0x270/0x2e0
[<c06fcbf8>] rest_init+0xd4/0xe4
[<c0a44bfc>] start_kernel+0x3d0/0x3dc
[<80008084>] 0x80008084
INITIAL USE at:
[<c0090040>] lock_acquire+0x9c/0x158
[<c070674c>] _raw_spin_lock_irqsave+0x54/0x68
[<c009aff8>] __irq_get_desc_lock+0x64/0xa4
[<c009e38c>] irq_set_chip+0x30/0x78
[<c009ec30>] irq_set_chip_and_handler_name+0x24/0x3c
[<c036ca10>] gic_irq_domain_map+0x48/0xb4
[<c00a0a80>] irq_domain_associate+0x84/0x1d4
[<c00a1154>] irq_create_mapping+0x80/0x11c
[<c00a1270>] irq_create_of_mapping+0x80/0x120
[<c05cdaa8>] irq_of_parse_and_map+0x34/0x3c
[<c0a4ea24>] omap_dm_timer_init_one+0x90/0x30c
[<c0a4eef0>] omap5_realtime_timer_init+0x8c/0x48c
[<c0a486b0>] time_init+0x28/0x38
[<c0a44a6c>] start_kernel+0x240/0x3dc
[<80008084>] 0x80008084
}
... key at: [<c1049ce0>] irq_desc_lock_class+0x0/0x8
... acquired at:
[<c07065c8>] _raw_spin_lock+0x48/0x58
[<c0375a90>] pcs_irq_unmask+0x58/0xa0
[<c009ea48>] irq_enable+0x38/0x48
[<c009ead0>] irq_startup+0x78/0x7c
[<c009d440>] __setup_irq+0x4a8/0x4f4
[<c009d5dc>] request_threaded_irq+0xb8/0x138
[<c0415a5c>] omap_8250_startup+0x4c/0x148
[<c041276c>] serial8250_startup+0x24/0x30
[<c040d0ec>] uart_startup.part.9+0x5c/0x1b4
[<c040dbcc>] uart_open+0xf4/0x16c
[<c03f0540>] tty_open+0x170/0x61c
[<c0157028>] chrdev_open+0xbc/0x1b4
[<c0150494>] do_dentry_open+0x1e8/0x2bc
[<c0150a84>] finish_open+0x44/0x5c
[<c0160d50>] do_last.isra.47+0x710/0xca0
[<c01613a4>] path_openat+0xc4/0x640
[<c0162904>] do_filp_open+0x3c/0x98
[<c0151bdc>] do_sys_open+0x114/0x1d8
[<c0151cc8>] SyS_open+0x28/0x2c
[<c0a44d70>] kernel_init_freeable+0x168/0x1e4
[<c06fcc24>] kernel_init+0x1c/0xf8
[<c000eee8>] ret_from_fork+0x14/0x20
-> (&pcs->lock){+.....} ops: 65 {
HARDIRQ-ON-W at:
[<c0090040>] lock_acquire+0x9c/0x158
[<c07065c8>] _raw_spin_lock+0x48/0x58
[<c0375b54>] pcs_irq_handle+0x48/0x9c
[<c0375c5c>] pcs_irq_handler+0x1c/0x28
[<c009c458>] irq_forced_thread_fn+0x30/0x74
[<c009c784>] irq_thread+0x158/0x1c4
[<c0063fc4>] kthread+0xd4/0xe8
[<c000eee8>] ret_from_fork+0x14/0x20
INITIAL USE at:
[<c0090040>] lock_acquire+0x9c/0x158
[<c070674c>] _raw_spin_lock_irqsave+0x54/0x68
[<c0375344>] pcs_enable+0x7c/0xe8
[<c0372a44>] pinmux_enable_setting+0x178/0x220
[<c036fecc>] pinctrl_select_state+0x110/0x194
[<c04732dc>] pinctrl_bind_pins+0x7c/0x108
[<c045853c>] driver_probe_device+0x70/0x254
[<c0458810>] __driver_attach+0x9c/0xa0
[<c045674c>] bus_for_each_dev+0x78/0xac
[<c0458030>] driver_attach+0x2c/0x30
[<c0457c78>] bus_add_driver+0x15c/0x204
[<c0458ee0>] driver_register+0x88/0x108
[<c045a168>] __platform_driver_register+0x64/0x6c
[<c0a8170c>] omap_hsmmc_driver_init+0x1c/0x20
[<c0008a94>] do_one_initcall+0x110/0x170
[<c0a44d48>] kernel_init_freeable+0x140/0x1e4
[<c06fcc24>] kernel_init+0x1c/0xf8
[<c000eee8>] ret_from_fork+0x14/0x20
}
... key at: [<c1088a8c>] __key.18572+0x0/0x8
... acquired at:
[<c008cdd4>] mark_lock+0x388/0x76c
[<c008df40>] __lock_acquire+0x6d0/0x1f98
[<c0090040>] lock_acquire+0x9c/0x158
[<c07065c8>] _raw_spin_lock+0x48/0x58
[<c0375b54>] pcs_irq_handle+0x48/0x9c
[<c0375c5c>] pcs_irq_handler+0x1c/0x28
[<c009c458>] irq_forced_thread_fn+0x30/0x74
[<c009c784>] irq_thread+0x158/0x1c4
[<c0063fc4>] kthread+0xd4/0xe8
[<c000eee8>] ret_from_fork+0x14/0x20
stack backtrace:
CPU: 1 PID: 927 Comm: irq/369-pinctrl Not tainted 3.14.43-rt42-00360-g96ff499-dirty #24
[<c00177e0>] (unwind_backtrace) from [<c00130b0>] (show_stack+0x20/0x24)
[<c00130b0>] (show_stack) from [<c0702958>] (dump_stack+0x84/0xd0)
[<c0702958>] (dump_stack) from [<c008bcfc>] (print_irq_inversion_bug+0x1d0/0x21c)
[<c008bcfc>] (print_irq_inversion_bug) from [<c008bf18>] (check_usage_backwards+0xb4/0x11c)
[<c008bf18>] (check_usage_backwards) from [<c008cdd4>] (mark_lock+0x388/0x76c)
[<c008cdd4>] (mark_lock) from [<c008df40>] (__lock_acquire+0x6d0/0x1f98)
[<c008df40>] (__lock_acquire) from [<c0090040>] (lock_acquire+0x9c/0x158)
[<c0090040>] (lock_acquire) from [<c07065c8>] (_raw_spin_lock+0x48/0x58)
[<c07065c8>] (_raw_spin_lock) from [<c0375b54>] (pcs_irq_handle+0x48/0x9c)
[<c0375b54>] (pcs_irq_handle) from [<c0375c5c>] (pcs_irq_handler+0x1c/0x28)
[<c0375c5c>] (pcs_irq_handler) from [<c009c458>] (irq_forced_thread_fn+0x30/0x74)
[<c009c458>] (irq_forced_thread_fn) from [<c009c784>] (irq_thread+0x158/0x1c4)
[<c009c784>] (irq_thread) from [<c0063fc4>] (kthread+0xd4/0xe8)
[<c0063fc4>] (kthread) from [<c000eee8>] (ret_from_fork+0x14/0x20)
To fix it use IRQF_NO_THREAD to ensure that pcs irq will not be forced threaded.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The PFC driver causes the kernel to hang on the R-Car gen2 SoC based boards
when the CPU_ALL_PORT() macro is fixed to reflect the reality, i.e. when the
GPIO space becomes actually sparse. This happens because the _GP_GPIO() macro
includes an indexed initializer which causes the "holes" (array entries filled
with all 0s) between the groups of the existing GPIOs; and the driver can't
cope with that. There seems to be no reason to use the indexed initializer,
so we can remove the index specifier and so avoid the "holes".
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Commit a21763a0b1e5a5ab8310f581886d04beadc16616
"pinctrl: nomadik: activate strict mux mode"
put all Nomadik pin controllers to strict mode. This was
not good on the Snowball platform: the muxing of GPIOs to
different pins is done with hogs in the DTS file, and then
these GPIOs are used by offset, relying on hogs to mux the
pins. Since that means the pin controller "owns" the pins
and at the same time we have a GPIO user, this pin controller
is by definition not strict.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two fairly simple fixes: one is a change that causes us to have a very
low queue depth leading to performance issues and the other is a null
deref occasionally in tapes thanks to use after put"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: fix host max depth checking for the 'queue_depth' sysfs interface
st: null pointer dereference panic caused by use after kref_put by st_open
|
|
Pull MIPS fixes from Ralf Baechle:
"Another round of MIPS fixes for 4.2.
Things are looking quite decent at this stage but the recent work on
the FPU support took its toll:
- fix an incorrect overly restrictive ifdef
- select O32 64-bit FP support for O32 binary compatibility
- remove workarounds for Sibyte SB1250 Pass1 parts. There are rare
fixing the workarounds is not worth the effort.
- patch up an outdated and now incorrect comment"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: fpu.h: Allow 64-bit FPU on a 64-bit MIPS R6 CPU
MIPS: SB1: Remove support for Pass 1 parts.
MIPS: Require O32 FP64 support for MIPS64 with O32 compat
MIPS: asm-offset.c: Patch up various comments refering to the old filename.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc fix from Helge Deller:
"A memory leak fix from Christophe Jaillet which was introduced with
kernel 4.0 and which leads to kernel crashes on parisc after 1-3 days"
* 'parisc-4.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: mm: Fix a memory leak related to pmd not attached to the pgd
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"By far most of the fixes here are updates to DTS files to deal with
some mostly minor bugs.
There's also a fix to deal with non-PM kernel configs on i.MX, a
regression fix for ethernet on PXA platforms and a dependency fix for
OMAP"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: keystone: dts: rename pcie nodes to help override status
ARM: keystone: dts: fix dt bindings for PCIe
ARM: pxa: fix dm9000 platform data regression
ARM: dts: Correct audio input route & set mic bias for am335x-pepper
ARM: OMAP2+: Add HAVE_ARM_SCU for AM43XX
MAINTAINERS: digicolor: add dts files
ARM: ux500: fix MMC/SD card regression
ARM: ux500: define serial port aliases
ARM: dts: OMAP5: Add #iommu-cells property to IOMMUs
ARM: dts: OMAP4: Add #iommu-cells property to IOMMUs
ARM: dts: Fix frequency scaling on Gumstix Pepper
ARM: dts: configure regulators for Gumstix Pepper
ARM: dts: omap3: overo: Update LCD panel names
ARM: dts: cros-ec-keyboard: Add support for some Japanese keys
ARM: imx6: gpc: always enable PU domain if CONFIG_PM is not set
ARM: dts: imx53-qsb: fix TVE entry
ARM: dts: mx23: fix iio-hwmon support
ARM: dts: imx27: Adjust the GPT compatible string
ARM: socfpga: dts: Fix entries order
ARM: socfpga: dts: Fix adxl34x formating and compatible string
|
|
Commit 6134d94923d0 ("MIPS: asm: fpu: Allow 64-bit FPU on MIPS32 R6")
added support for 64-bit FPU on a 32-bit MIPS R6 processor but it missed
the 64-bit CPU case leading to FPU failures when requesting FR=1 mode
(which is always the case for MIPS R6 userland) when running a 32-bit
kernel on a 64-bit CPU. We also fix the MIPS R2 case.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Fixes: 6134d94923d0 ("MIPS: asm: fpu: Allow 64-bit FPU on MIPS32 R6")
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Cc: <stable@vger.kernel.org> # 4.0+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10734/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Commit 0e0da48dee8d ("parisc: mm: don't count preallocated pmds")
introduced a memory leak.
After this commit, the 'return' statement in pmd_free is executed in all
cases. Even for pmd that are not attached to the pgd. So 'free_pages'
can never be called anymore, leading to a memory leak.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Mikulas Patocka <mpatocka@redhat.com>
Acked-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # v4.0+
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Merge "pxa fixes for v4.2" from Robert Jarzmik:
ARM: pxa: fixes for v4.2-rc2
This single fix reenables ethernet cards for several pxa boards,
broken by regulator addition to dm9000 driver.
* tag 'pxa-fixes-v4.2-rc2' of https://github.com/rjarzmik/linux:
ARM: pxa: fix dm9000 platform data regression
|
|
Pull ARM fixes from Russell King:
"A small set of ARM fixes for -rc3, most of them not far off
one-liners, with the exception of fixing the V7 cache invalidation for
incoming SMP processors which was causing problems for SoCFPGA
devices"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: fix __virt_to_idmap build error on !MMU
ARM: invalidate L1 before enabling coherency
ARM: 8404/1: dma-mapping: fix off-by-one error in bitmap size check
ARM: 8402/1: perf: Don't use of_node after putting it
ARM: 8400/1: use virt_to_idmap to get phys_reset address
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"Two families of fixes:
- Fix an FPU context related boot crash on newer x86 hardware with
larger context sizes than what most people test. To fix this
without ugly kludges or extensive reverts we had to touch core task
allocator, to allow x86 to determine the task size dynamically, at
boot time.
I've tested it on a number of x86 platforms, and I cross-built it
to a handful of architectures:
(warns) (warns)
testing x86-64: -git: pass ( 0), -tip: pass ( 0)
testing x86-32: -git: pass ( 0), -tip: pass ( 0)
testing arm: -git: pass ( 1359), -tip: pass ( 1359)
testing cris: -git: pass ( 1031), -tip: pass ( 1031)
testing m32r: -git: pass ( 1135), -tip: pass ( 1135)
testing m68k: -git: pass ( 1471), -tip: pass ( 1471)
testing mips: -git: pass ( 1162), -tip: pass ( 1162)
testing mn10300: -git: pass ( 1058), -tip: pass ( 1058)
testing parisc: -git: pass ( 1846), -tip: pass ( 1846)
testing sparc: -git: pass ( 1185), -tip: pass ( 1185)
... so I hope the cross-arch impact 'none', as intended.
(by Dave Hansen)
- Fix various NMI handling related bugs unearthed by the big asm code
rewrite and generally make the NMI code more robust and more
maintainable while at it. These changes are a bit late in the
cycle, I hope they are still acceptable.
(by Andy Lutomirski)"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/fpu, sched: Introduce CONFIG_ARCH_WANTS_DYNAMIC_TASK_STRUCT and use it on x86
x86/fpu, sched: Dynamically allocate 'struct fpu'
x86/entry/64, x86/nmi/64: Add CONFIG_DEBUG_ENTRY NMI testing code
x86/nmi/64: Make the "NMI executing" variable more consistent
x86/nmi/64: Minor asm simplification
x86/nmi/64: Use DF to avoid userspace RSP confusing nested NMI detection
x86/nmi/64: Reorder nested NMI checks
x86/nmi/64: Improve nested NMI comments
x86/nmi/64: Switch stacks on userspace NMI entry
x86/nmi/64: Remove asm code that saves CR2
x86/nmi: Enable nested do_nmi() handling for 64-bit kernels
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fix from Ingo Molnar:
"Fix for a misplaced export that can cause build failures in certain
(rare) Kconfig situations"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tick: Move the export of tick_broadcast_oneshot_control to the proper place
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fix from Ingo Molnar:
"A oneliner rq throttling fix"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/fair: Test list head instead of list entry in throttle_cfs_rq()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Mostly tooling fixes, plus a static key fix fixing /sys/devices/cpu/rdpmc"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf tools: Really allow to specify custom CC, AR or LD
perf auxtrace: Fix misplaced check for HAVE_SYNC_COMPARE_AND_SWAP_SUPPORT
perf hists browser: Take the --comm, --dsos, etc filters into account
perf symbols: Store if there is a filter in place
x86, perf: Fix static_key bug in load_mm_cr4()
tools: Copy lib/hweight.c from the kernel sources
perf tools: Fix the detached tarball wrt rbtree copy
perf thread_map: Fix the sizeof() calculation for map entries
tools lib: Improve clean target
perf stat: Fix shadow declaration of close
perf tools: Fix lockup using 32-bit compat vdso
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Ingo Molnar:
"Misc irq fixes:
- two driver fixes
- a Xen regression fix
- a nested irq thread crash fix"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gicv3-its: Fix mapping of LPIs to collections
genirq: Prevent resend to interrupts marked IRQ_NESTED_THREAD
genirq: Revert sparse irq locking around __cpu_up() and move it to x86 for now
gpio/davinci: Fix race in installing chained irq handler
|
|
Merge fixes from Andrew Morton:
"25 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (25 commits)
lib/decompress: set the compressor name to NULL on error
mm/cma_debug: correct size input to bitmap function
mm/cma_debug: fix debugging alloc/free interface
mm/page_owner: set correct gfp_mask on page_owner
mm/page_owner: fix possible access violation
fsnotify: fix oops in fsnotify_clear_marks_by_group_flags()
/proc/$PID/cmdline: fixup empty ARGV case
dma-debug: skip debug_dma_assert_idle() when disabled
hexdump: fix for non-aligned buffers
checkpatch: fix long line messages about patch context
mm: clean up per architecture MM hook header files
MAINTAINERS: uclinux-h8-devel is moderated for non-subscribers
mailmap: update Sudeep Holla's email id
Update Viresh Kumar's email address
mm, meminit: suppress unused memory variable warning
configfs: fix kernel infoleak through user-controlled format string
include, lib: add __printf attributes to several function prototypes
s390/hugetlb: add hugepages_supported define
mm: hugetlb: allow hugepages_supported to be architecture specific
revert "s390/mm: make hugepages_supported a boot time decision"
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"These are all from Filipe, and cover a few problems we've had reported
on the list recently (along with ones he found on his own)"
* 'for-linus-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix file corruption after cloning inline extents
Btrfs: fix order by which delayed references are run
Btrfs: fix list transaction->pending_ordered corruption
Btrfs: fix memory leak in the extent_same ioctl
Btrfs: fix shrinking truncate when the no_holes feature is enabled
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull rtc fixes from Alexandre Belloni:
"A few fixes for the RTC susbsystem for 4.2.
The mt6397 driver was introduce in 4.2 so it is worth fixing before
the final release. I though the compilation warning for armada38x was
fixed by akpm in commit f98b733e93e0 ("rtc-armada38x.c: remove unused
local `flags'") but he actually missed some occurrences of the
variables. Since I received 4 patches for that, I think we can
include it now.
Summary:
- fix mt6397 wakealarm creation
- remove a compilation warning for armada38x that was forgotten"
* tag 'rtc-v4.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
rtc: armada38x: Remove unused variable from armada38x_rtc_set_time()
rtc: mt6397: enable wakeup before registering rtc device
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- revert a request-based DM core change that caused IO latency to
increase and adversely impact both throughput and system load
- fix for a use after free bug in DM core's device cleanup
- a couple DM btree removal fixes (used by dm-thinp)
- a DM thinp fix for order-5 allocation failure
- a DM thinp fix to not degrade to read-only metadata mode when in
out-of-data-space mode for longer than the 'no_space_timeout'
- fix a long-standing oversight in both dm-thinp and dm-cache by now
exporting 'needs_check' in status if it was set in metadata
- fix an embarrassing dm-cache busy-loop that caused worker threads to
eat cpu even if no IO was actively being issued to the cache device
* tag 'dm-4.2-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm cache: avoid calls to prealloc_free_structs() if possible
dm cache: avoid preallocation if no work in writeback_some_dirty_blocks()
dm cache: do not wake_worker() in free_migration()
dm cache: display 'needs_check' in status if it is set
dm thin: display 'needs_check' in status if it is set
dm thin: stay in out-of-data-space mode once no_space_timeout expires
dm: fix use after free crash due to incorrect cleanup sequence
Revert "dm: only run the queue on completion if congested or no requests pending"
dm btree: silence lockdep lock inversion in dm_btree_del()
dm thin: allocate the cell_sort_array dynamically
dm btree remove: fix bug in redistribute3
|
|
on x86
Don't burden architectures without dynamic task_struct sizing
with the overhead of dynamic sizing.
Also optimize the x86 code a bit by caching task_struct_size.
Acked-and-Tested-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave@sr71.net>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1437128892-9831-3-git-send-email-mingo@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The FPU rewrite removed the dynamic allocations of 'struct fpu'.
But, this potentially wastes massive amounts of memory (2k per
task on systems that do not have AVX-512 for instance).
Instead of having a separate slab, this patch just appends the
space that we need to the 'task_struct' which we dynamically
allocate already. This saves from doing an extra slab
allocation at fork().
The only real downside here is that we have to stick everything
and the end of the task_struct. But, I think the
BUILD_BUG_ON()s I stuck in there should keep that from being too
fragile.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave@sr71.net>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1437128892-9831-2-git-send-email-mingo@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Without this we end up using the previous name of the compressor in the
loop in unpack_rootfs. For example we get errors like "compression
method gzip not configured" even when we have CONFIG_DECOMPRESS_GZIP
enabled.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In CMA, 1 bit in bitmap means 1 << order_per_bits pages so size of
bitmap is cma->count >> order_per_bits rather than just cma->count.
This patch fixes it.
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Cc: Sasha Levin <sasha.levin@oracle.com>
Cc: Stefan Strogin <stefan.strogin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
CMA has alloc/free interface for debugging. It is intended that
alloc/free occurs in specific CMA region, but, currently, alloc/free
interface is on root dir due to the bug so we can't select CMA region
where alloc/free happens.
This patch fixes this problem by making alloc/free interface per CMA
region.
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Cc: Sasha Levin <sasha.levin@oracle.com>
Cc: Stefan Strogin <stefan.strogin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Currently, we set wrong gfp_mask to page_owner info in case of isolated
freepage by compaction and split page. It causes incorrect mixed
pageblock report that we can get from '/proc/pagetypeinfo'. This metric
is really useful to measure fragmentation effect so should be accurate.
This patch fixes it by setting correct information.
Without this patch, after kernel build workload is finished, number of
mixed pageblock is 112 among roughly 210 movable pageblocks.
But, with this fix, output shows that mixed pageblock is just 57.
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When I tested my new patches, I found that page pointer which is used
for setting page_owner information is changed. This is because page
pointer is used to set new migratetype in loop. After this work, page
pointer could be out of bound. If this wrong pointer is used for
page_owner, access violation happens. Below is error message that I
got.
BUG: unable to handle kernel paging request at 0000000000b00018
IP: [<ffffffff81025f30>] save_stack_address+0x30/0x40
PGD 1af2d067 PUD 166e0067 PMD 0
Oops: 0002 [#1] SMP
...snip...
Call Trace:
print_context_stack+0xcf/0x100
dump_trace+0x15f/0x320
save_stack_trace+0x2f/0x50
__set_page_owner+0x46/0x70
__isolate_free_page+0x1f7/0x210
split_free_page+0x21/0xb0
isolate_freepages_block+0x1e2/0x410
compaction_alloc+0x22d/0x2d0
migrate_pages+0x289/0x8b0
compact_zone+0x409/0x880
compact_zone_order+0x6d/0x90
try_to_compact_pages+0x110/0x210
__alloc_pages_direct_compact+0x3d/0xe6
__alloc_pages_nodemask+0x6cd/0x9a0
alloc_pages_current+0x91/0x100
runtest_store+0x296/0xa50
simple_attr_write+0xbd/0xe0
__vfs_write+0x28/0xf0
vfs_write+0xa9/0x1b0
SyS_write+0x46/0xb0
system_call_fastpath+0x16/0x75
This patch fixes this error by moving up set_page_owner().
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
fsnotify_clear_marks_by_group_flags() can race with
fsnotify_destroy_marks() so when fsnotify_destroy_mark_locked() drops
mark_mutex, a mark from the list iterated by
fsnotify_clear_marks_by_group_flags() can be freed and we dereference free
memory in the loop there.
Fix the problem by keeping mark_mutex held in
fsnotify_destroy_mark_locked(). The reason why we drop that mutex is that
we need to call a ->freeing_mark() callback which may acquire mark_mutex
again. To avoid this and similar lock inversion issues, we move the call
to ->freeing_mark() callback to the kthread destroying the mark.
Signed-off-by: Jan Kara <jack@suse.cz>
Reported-by: Ashish Sangwan <a.sangwan@samsung.com>
Suggested-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
/proc/*/cmdline code checks if it should look at ENVP area by checking
last byte of ARGV area:
rv = access_remote_vm(mm, arg_end - 1, &c, 1, 0);
if (rv <= 0)
goto out_free_page;
If ARGV is somehow made empty (by doing execve(..., NULL, ...) or
manually setting ->arg_start and ->arg_end to equal values), the decision
will be based on byte which doesn't even belong to ARGV/ENVP.
So, quickly check if ARGV area is empty and report 0 to match previous
behaviour.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
If dma-debug is disabled due to a memory error, DMA unmaps do not affect
the dma_active_cacheline radix tree anymore, and debug_dma_assert_idle()
can print false warnings.
Disable debug_dma_assert_idle() when dma_debug_disabled() is true.
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Fixes: 0abdd7a81b7e ("dma-debug: introduce debug_dma_assert_idle()")
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Sebastian Ott <sebott@linux.vnet.ibm.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Horia Geanta <horia.geanta@freescale.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
A hexdump with a buf not aligned to the groupsize causes
non-naturally-aligned memory accesses. This was causing a kernel panic
on the processor BlackFin BF527, when such an unaligned buffer was fed
by the function ubifs_scanned_corruption in fs/ubifs/scan.c .
To fix this, change accesses to the contents of the buffer so they go
through get_unaligned(). This change should be harmless to unaligned-
access-capable architectures, and any performance hit should be anyway
dwarfed by the snprintf() processing time.
Signed-off-by: Horacio Mijail Antón Quiles <hmijail@gmail.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Joe Perches <joe@perches.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Changes in ("checkpatch: categorize some long line length checks")
now erroneously reports long line defects in patch context.
Fix it.
Signed-off-by: Joe Perches <joe@perches.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
