| Age | Commit message (Collapse) | Author |
|---|
|
Enable J721E SoC support from TI.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
Add Support for J721E Common Processor board support.
The EVM architecture is as follows:
+------------------------------------------------------+
| +-------------------------------------------+ |
| | | |
| | Add-on Card 1 Options | |
| | | |
| +-------------------------------------------+ |
| |
| |
| +-------------------+ |
| | | |
| | SOM | |
| +--------------+ | | |
| | | | | |
| | Add-on | +-------------------+ |
| | Card 2 | | Power Supply
| | Options | | |
| | | | |
| +--------------+ | <---
+------------------------------------------------------+
Common Processor Board
Common Processor board is the baseboard that has most of the actual
connectors, power supply etc. A SOM (System on Module) is plugged on
to the common processor board and this contains the SoC, PMIC, DDR and
basic high speed components necessary for functionality. Add-n card
options add further functionality (such as additional Audio, Display,
networking options).
Note:
A) The minimum configuration required to boot up the board is System On
Module(SOM) + Common Processor Board.
B) Since there is just a single SOM and Common Processor Board, we are
maintaining common processor board as the base dts and SOM as the dtsi
that we include. In the future as more SOM's appear, we should move
common processor board as a dtsi and include configurations as dts.
C) All daughter cards beyond the basic boards shall be maintained as
overlays.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
Add option to build J721E SoC specific components
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
The J721E SoC belongs to the K3 Multicore SoC architecture platform,
providing advanced system integration to enable lower system costs
of automotive applications such as infotainment, cluster, premium
Audio, Gateway, industrial and a range of broad market applications.
This SoC is designed around reducing the system cost by eliminating
the need of an external system MCU and is targeted towards ASIL-B/C
certification/requirements in addition to allowing complex software
and system use-cases.
Some highlights of this SoC are:
* Dual Cortex-A72s in a single cluster, three clusters of lockstep
capable dual Cortex-R5F MCUs, Deep-learning Matrix Multiply Accelerator(MMA),
C7x floating point Vector DSP, Two C66x floating point DSPs.
* 3D GPU PowerVR Rogue 8XE GE8430
* Vision Processing Accelerator (VPAC) with image signal processor and Depth
and Motion Processing Accelerator (DMPAC)
* Two Gigabit Industrial Communication Subsystems (ICSSG), each with dual
PRUs and dual RTUs
* Two CSI2.0 4L RX plus one CSI2.0 4L TX, one eDP/DP, One DSI Tx, and
up to two DPI interfaces.
* Integrated Ethernet switch supporting up to a total of 8 external ports in
addition to legacy Ethernet switch of up to 2 ports.
* System MMU (SMMU) Version 3.0 and advanced virtualisation
capabilities.
* Upto 4 PCIe-GEN3 controllers, 2 USB3.0 Dual-role device subsystems,
16 MCANs, 12 McASP, eMMC and SD, UFS, OSPI/HyperBus memory controller, QSPI,
I3C and I2C, eCAP/eQEP, eHRPWM, MLB among other peripherals.
* Two hardware accelerator block containing AES/DES/SHA/MD5 called SA2UL
management.
* Configurable L3 Cache and IO-coherent architecture with high data throughput
capable distributed DMA architecture under NAVSS
* Centralized System Controller for Security, Power, and Resource
Management (DMSC)
See J721E Technical Reference Manual (SPRUIL1, May 2019)
for further details: http://www.ti.com/lit/pdf/spruil1
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
J721e uses a UART controller that is compatible with AM654 UART.
Introduce a specific compatible to help handle the differences if
necessary.
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Vignesh R <vigneshr@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
The J721E SoC belongs to the K3 Multicore SoC architecture platform,
providing advanced system integration to enable lower system costs
of automotive applications such as infotainment, cluster, premium
Audio, Gateway, industrial and a range of broad market applications.
This SoC is designed around reducing the system cost by eliminating
the need of an external system MCU and is targeted towards ASIL-B/C
certification/requirements in addition to allowing complex software
and system use-cases.
Some highlights of this SoC are:
* Dual Cortex-A72s in a single cluster, three clusters of lockstep
capable dual Cortex-R5F MCUs, Deep-learning Matrix Multiply Accelerator(MMA),
C7x floating point Vector DSP, Two C66x floating point DSPs.
* 3D GPU PowerVR Rogue 8XE GE8430
* Vision Processing Accelerator (VPAC) with image signal processor and Depth
and Motion Processing Accelerator (DMPAC)
* Two Gigabit Industrial Communication Subsystems (ICSSG), each with dual
PRUs and dual RTUs
* Two CSI2.0 4L RX plus one CSI2.0 4L TX, one eDP/DP, One DSI Tx, and
up to two DPI interfaces.
* Integrated Ethernet switch supporting up to a total of 8 external ports in
addition to legacy Ethernet switch of up to 2 ports.
* System MMU (SMMU) Version 3.0 and advanced virtualisation
capabilities.
* Upto 4 PCIe-GEN3 controllers, 2 USB3.0 Dual-role device subsystems,
16 MCANs, 12 McASP, eMMC and SD, UFS, OSPI/HyperBus memory controller, QSPI,
I3C and I2C, eCAP/eQEP, eHRPWM, MLB among other peripherals.
* Two hardware accelerator block containing AES/DES/SHA/MD5 called SA2UL
management.
* Configurable L3 Cache and IO-coherent architecture with high data throughput
capable distributed DMA architecture under NAVSS
* Centralized System Controller for Security, Power, and Resource
Management (DMSC)
See J721E Technical Reference Manual (SPRUIL1, May 2019)
for further details: http://www.ti.com/lit/pdf/spruil1
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
This changes pm8998 to use the new qcom,pm8998-pon compatible
string for the pon in order to support the gen2 pon
functionality properly.
Cc: Andy Gross <agross@kernel.org>
Cc: David Brown <david.brown@linaro.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Amit Pundir <amit.pundir@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: devicetree@vger.kernel.org
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
|
|
Enable SMMUs on 8996 now that the WRZ workaround in the arm-smmu driver
has landed.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
|
|
The domain specifier was changed from using "reg" to "qcom,apr-domain",
update the dts accordingly.
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
This adds an initial dts for the Dragonboard 845. Supported
functionality includes Debug UART, UFS, USB-C (peripheral), USB-A
(host), microSD-card and Bluetooth.
Initializing the SMMU is clearing the mapping used for the splash screen
framebuffer, which causes the board to reboot. This can be worked around
using:
fastboot oem select-display-panel none
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Tested-by: Vinod Koul <vkoul@kernel.org>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
The SoC/board bindings for i.MX1/31/35 are undocumented. Add the missing
bindings to the schema.
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
In the conversion to DT schema, the addition of the i.MX7ULP binding got
dropped. Add it to the binding schema.
Fixes: a1a38e1f4d1d ("dt-bindings: arm: Convert FSL board/soc bindings to json-schema")
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The Emtrion board bindings landed when the i.MX board/SoC bindings were
being converted to DT schema. Add them to the schema and remove the
separate file.
Cc: Jan Tuerk <jan.tuerk@emtrion.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This is for the development kit board for the Librem 5. The current level
of support yields a working console and is able to boot userspace from
the network or eMMC.
Additional subsystems that are active :
- Both USB ports
- SD card socket
- WiFi usdhc
- WWAN modem
- GNSS
- GPIO keys
- LEDs
- gyro
- magnetometer
- touchscreen
- pwm
- backlight
- haptic motor
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add an entry for imx8mq based boards
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add an entry for Purism, SPC
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add the qDMA device tree nodes for LS1028A devices
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add LS1028A qDMA controller bindings to fsl-qdma bindings.
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Describe the dynamic power coefficient of A57 and A53 CPUs.
Based on work by Gaku Inami <gaku.inami.xw@bp.renesas.com> and others.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Setup a thermal zone driven by SoC temperature sensor. Create passive trip
points and bind them to CPUFreq cooling device that supports power
extension.
Based on work by Dien Pham <dien.pham.ry@renesas.com> for r8a7796 SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Set the capacity-dmips-mhz for RZ/G2M(r8a774a1) SoC, that is based on
dhrystone.
Based on work done by Gaku Inami <gaku.inami.xw@bp.renesas.com> for
r8a7796 SoC.
The average dhrystone result for 5 iterations is as below:
r8a774a1 SoC (CA57x2 + CA53x4)
CPU max-freq dhrystone
---------------------------------
CA57 1500 MHz 11428571 lps/s
CA53 1200 MHz 5000000 lps/s
From this, CPU capacity-dmips-mhz for CA57 and CA53 are calculated
as follows:
r8a774a1 SoC
CA57 : 1024 / (11428571 / 1500) * (11428571 / 1500) = 1024
CA53 : 1024 / (11428571 / 1500) * ( 5000000 / 1200) = 560
Since each CPUs have different max frequencies, the final CPU
capacities of A53 scaled by the above difference is as below
$ cat /sys/devices/system/cpu/cpu*/cpu_capacity
1024
1024
448
448
448
448
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
This patch adds the "cpu-map" into r8a774a1 composed of multi-cluster. This
definition is used to parse the cpu topology.
Based on work by Gaku Inami <gaku.inami.xw@bp.renesas.com> for r8a7796 SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
This patch adds LEDs support to the HiHope RZ/G2[MN] Main Board
common device tree.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
This patch enables USB3.0 host/peripheral device node for the HiHope
RZ/G2M board.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
The GPIO interrupt controllers are missing their required
specified in DT.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Neither pinctrl_i2c1_gpio nor pinctrl_i2c2_gpio are used anywhere in
the file, drop them.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
RPU2 uses UART2 as a serial console and UART1 is not used at all. Fix
incorrrectly specified 'stdout-path' to reflect that.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add devicetree support for 96Boards Meerkat96 board from Novtech. This
board is one of the Consumer Edition boards of the 96Boards family based
on i.MX7D SoC. Following are the currently supported features of the
board:
* uSD
* WiFi/BT
* USB
More information about this board can be found in 96Boards product page:
https://www.96boards.org/product/imx7-96/
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Document 96Boards Meerkat96 devicetree binding based on i.MX7D SoC.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add PXP node for i.MX6UL/L SoC.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The SNVS poweroff depends on board design, by default it should
be disabled in SoC DT and ONLY be enabled on board DT if it is
wired up to external PMIC.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The SNVS power key depends on board design, by default it should
be disabled in SoC DT and ONLY be enabled on board DT if it is
wired up.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The SNVS power key depends on board design, by default it should
be disabled in SoC DT and ONLY be enabled on board DT if it is
wired up.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The SNVS power key depends on board design, by default it should
be disabled in SoC DT and ONLY be enabled on board DT if it is
wired up.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The SNVS power key depends on board design, by default it should
be disabled in SoC DT and ONLY be enabled on board DT if it is
wired up.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The SNVS power key depends on board design, by default it should
be disabled in SoC DT and ONLY be enabled on board DT if it is
wired up.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The SNVS power key depends on board design, by default it should
be disabled in SoC DT and ONLY be enabled on board DT if it is
wired up.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Enable SNVS power key for i.MX8MQ EVK board.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
LS1028A has a SEC v5.0 compatible security engine.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Enable the PCIe PHY and controller found on the QCS404 EVB.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
The QCS404 has a PCIe2 PHY and a Qualcomm PCIe controller, define these
to for the platform.
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Add MSM8998 PCIe QMP PHY and PCIe root complex DT nodes.
Based on the following DTS downstream:
https://source.codeaurora.org/quic/la/kernel/msm-4.4/tree/arch/arm/boot/dts/qcom/msm8998.dtsi?h=LE.UM.1.3.r3.25#n2537
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
The MSM8998 ANOC1(*) SMMU services BLSP2, PCIe, UFS, and USB.
(*) Aggregate Network-on-Chip #1
Based on the following DTS downstream:
https://source.codeaurora.org/quic/la/kernel/msm-4.4/tree/arch/arm/boot/dts/qcom/msm-arm-smmu-8998.dtsi?h=LE.UM.1.3.r3.25#n18
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
AM654 base board does not have any PCIe slots. Disable all the
SERDES and PCIe instances.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
Add PCIe Endpoint DT node.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
Add PCIe Root Complex DT node.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
Add DT node for SERDES0 and SERDES1.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
Add mux-controller DT node as a child node of scm_conf. This is
required for muxing SERDES between USB, PCIe and ICSS2 SGMII.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
GIC_ITS used in AM654 platform has the same configuration as that of
GIC_ITS used in Socionext SoCs. Add "socionext,synquacer-pre-its"
property to get PCI MSI working.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
Add the MSCM RAM address space to the ranges property of the cbass_main
interconnect node so that the addresses can be translated properly.
This fixes the probe failure in the sram driver for the MSMC RAM node.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
