| Age | Commit message (Collapse) | Author |
|---|
|
All switch models configure the GLOBAL_CONTROL register with slightly
differences.
Discarding packets with excessive collisions
(GLOBAL_CONTROL_DISCARD_EXCESS) is specific to 6352 and similar
switches, and setting a maximum frame size
(GLOBAL_CONTROL_MAX_FRAME_1632) is specific to 6185 and similar
switches.
As we are centralizing the chips setup, skip these settings and don't
discard any frames yet, until we found out that such discarding by the
hardware is necessary.
Assume a common setup to enable the PHY Polling Unit if present, don't
discard any packets, and mask all interrupt sources.
Tested on 88E6352 and 88E6185.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Every driver is calling mv88e6xxx_setup_global after
mv88e6xxx_setup_common. Call the former in the latter.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a MV88E6XXX_FLAG_PPU_ACTIVE flag to describe how to reset the
switch, and merge the reset call to the common setup code.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a MV88E6XXX_FLAG_ATU flag to identify switch models with an Address
Translation Unit.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a MV88E6XXX_FLAG_VTU flag to indentify switch models with a VLAN
Table Unit.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add MV88E6XXX_FLAG_PORTSTATE and MV88E6XXX_FLAG_VLANTABLE flags to
identify switch models with required 802.1D operations.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only 6131 was not supporting the port registers access yet. Assume such
support and use the unlock access routines in the meantime.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a MV88E6XXX_FLAG_EEE flag to describe switch models featuring Energy
Efficient Ethernet. Use it to conditionally support such access in the
common code.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some switch models have a dedicated register for Switch MAC/WoF/WoL.
This register, when present, is used to indirectly set the switch MAC
address, instead of a direct write to 3 global registers.
Identify this feature and share a common mv88e6xxx_set_addr function.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add MV88E6XXX_FLAG_TEMP and MV88E6XXX_FLAG_TEMP_LIMIT flags to describe
switch models featuring a temperature access. Use them to centralize the
access to the temperature feature.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a MV88E6XXX_FLAG_EEPROM flag to describe switch models featuring an
EEPROM and distribute the EEPROM access routines to all models.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some switch has dedicated SMI PHY Command and Data registers, used to
indirectly access the PHYs, instead of direct access.
Identify these switch models and make mv88e6xxx_phy_{read,write} generic
enough to support every models.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a MV88E6XXX_FLAG_PPU flag to describe switch models with a PHY
Polling Unit. This allows to merge PPU specific PHY access code in the
share code.
Make the mv88e6xxx_ppu_disable and mv88e6xxx_phy_{read,write}_ppu
functions use unlocked register accesses in order to call them in
mv88e6xxx_phy_{read,write} in a locked context.
Since the PPU code is shared, also remove NET_DSA_MV88E6XXX_NEED_PPU.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a flags bitmap to the info structure in order to identify features
supported or not by the different switch models.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
they are open-coded in all users except iov_iter_advance(), and there
they wouldn't be a bad idea either - as it is, iov_iter_advance(i, 0)
ends up dereferencing potentially past the end of iovec array. It
doesn't do anything with the value it reads, and very unlikely to
trigger an oops on dereference, but it is not impossible.
Reported-by: Jiri Slaby <jslaby@suse.cz>
Reported-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Fix the error message printed when attempting and failing to create the
call path root incorrectly references the call return process.
This change fixes the message to properly reference the failure to
create the call path root.
Signed-off-by: Chris Phlipot <cphlipot0@gmail.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1462612620-25008-2-git-send-email-cphlipot0@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Scale values by unit before passing them to the metrics printing
functions. This is needed for TopDown, because it needs to scale the
slots correctly by pipeline width / SMTness.
For existing metrics it shouldn't make any difference, as those
generally use events that don't have any units.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1462489447-31832-8-git-send-email-andi@firstfloor.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
NULL pointer derefence happens when booting with DTB because the
platform data for haptic device is not set in supplied data from parent
MFD device.
The MFD device creates only platform data (from Device Tree) for itself,
not for haptic child.
Unable to handle kernel NULL pointer dereference at virtual address 0000009c
pgd = c0004000
[0000009c] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
(max8997_haptic_probe) from [<c03f9cec>] (platform_drv_probe+0x4c/0xb0)
(platform_drv_probe) from [<c03f8440>] (driver_probe_device+0x214/0x2c0)
(driver_probe_device) from [<c03f8598>] (__driver_attach+0xac/0xb0)
(__driver_attach) from [<c03f67ac>] (bus_for_each_dev+0x68/0x9c)
(bus_for_each_dev) from [<c03f7a38>] (bus_add_driver+0x1a0/0x218)
(bus_add_driver) from [<c03f8db0>] (driver_register+0x78/0xf8)
(driver_register) from [<c0101774>] (do_one_initcall+0x90/0x1d8)
(do_one_initcall) from [<c0a00dbc>] (kernel_init_freeable+0x15c/0x1fc)
(kernel_init_freeable) from [<c06bb5b4>] (kernel_init+0x8/0x114)
(kernel_init) from [<c0107938>] (ret_from_fork+0x14/0x3c)
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: <stable@vger.kernel.org>
Fixes: 104594b01ce7 ("Input: add driver support for MAX8997-haptic")
[k.kozlowski: Write commit message, add CC-stable]
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
As pointed out by Richard, the changes to the comment got missed off
the absolute mode patch somehow.
Signed-off-by: Chris Diamand <chris@diamand.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Replace custom approach by %*ph specifier to dump small buffers in hex format.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
There is no need to check for DWARF unwinding support when using the
'dwarf' callchain record method, as this will only ask the kernel to
collect stack dumps for later DWARF CFI processing, which can be done in
another machine, where the support for DWARF unwinding need to be
present.
Signed-off-by: He Kuang <hekuang@huawei.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Ekaterina Tumanova <tumanova@linux.vnet.ibm.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Kan Liang <kan.liang@intel.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/r/1462525154-125656-2-git-send-email-hekuang@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Patch summary:
When showing a cgroupfs entry in mountinfo, show the path of the mount
root dentry relative to the reader's cgroup namespace root.
Short explanation (courtesy of mkerrisk):
If we create a new cgroup namespace, then we want both /proc/self/cgroup
and /proc/self/mountinfo to show cgroup paths that are correctly
virtualized with respect to the cgroup mount point. Previous to this
patch, /proc/self/cgroup shows the right info, but /proc/self/mountinfo
does not.
Long version:
When a uid 0 task which is in freezer cgroup /a/b, unshares a new cgroup
namespace, and then mounts a new instance of the freezer cgroup, the new
mount will be rooted at /a/b. The root dentry field of the mountinfo
entry will show '/a/b'.
cat > /tmp/do1 << EOF
mount -t cgroup -o freezer freezer /mnt
grep freezer /proc/self/mountinfo
EOF
unshare -Gm bash /tmp/do1
> 330 160 0:34 / /sys/fs/cgroup/freezer rw,nosuid,nodev,noexec,relatime - cgroup cgroup rw,freezer
> 355 133 0:34 /a/b /mnt rw,relatime - cgroup freezer rw,freezer
The task's freezer cgroup entry in /proc/self/cgroup will simply show
'/':
grep freezer /proc/self/cgroup
9:freezer:/
If instead the same task simply bind mounts the /a/b cgroup directory,
the resulting mountinfo entry will again show /a/b for the dentry root.
However in this case the task will find its own cgroup at /mnt/a/b,
not at /mnt:
mount --bind /sys/fs/cgroup/freezer/a/b /mnt
130 25 0:34 /a/b /mnt rw,nosuid,nodev,noexec,relatime shared:21 - cgroup cgroup rw,freezer
In other words, there is no way for the task to know, based on what is
in mountinfo, which cgroup directory is its own.
Example (by mkerrisk):
First, a little script to save some typing and verbiage:
echo -e "\t/proc/self/cgroup:\t$(cat /proc/self/cgroup | grep freezer)"
cat /proc/self/mountinfo | grep freezer |
awk '{print "\tmountinfo:\t\t" $4 "\t" $5}'
Create cgroup, place this shell into the cgroup, and look at the state
of the /proc files:
2653
2653 # Our shell
14254 # cat(1)
/proc/self/cgroup: 10:freezer:/a/b
mountinfo: / /sys/fs/cgroup/freezer
Create a shell in new cgroup and mount namespaces. The act of creating
a new cgroup namespace causes the process's current cgroups directories
to become its cgroup root directories. (Here, I'm using my own version
of the "unshare" utility, which takes the same options as the util-linux
version):
Look at the state of the /proc files:
/proc/self/cgroup: 10:freezer:/
mountinfo: / /sys/fs/cgroup/freezer
The third entry in /proc/self/cgroup (the pathname of the cgroup inside
the hierarchy) is correctly virtualized w.r.t. the cgroup namespace, which
is rooted at /a/b in the outer namespace.
However, the info in /proc/self/mountinfo is not for this cgroup
namespace, since we are seeing a duplicate of the mount from the
old mount namespace, and the info there does not correspond to the
new cgroup namespace. However, trying to create a new mount still
doesn't show us the right information in mountinfo:
# propagating to other mountns
/proc/self/cgroup: 7:freezer:/
mountinfo: /a/b /mnt/freezer
The act of creating a new cgroup namespace caused the process's
current freezer directory, "/a/b", to become its cgroup freezer root
directory. In other words, the pathname directory of the directory
within the newly mounted cgroup filesystem should be "/",
but mountinfo wrongly shows us "/a/b". The consequence of this is
that the process in the cgroup namespace cannot correctly construct
the pathname of its cgroup root directory from the information in
/proc/PID/mountinfo.
With this patch, the dentry root field in mountinfo is shown relative
to the reader's cgroup namespace. So the same steps as above:
/proc/self/cgroup: 10:freezer:/a/b
mountinfo: / /sys/fs/cgroup/freezer
/proc/self/cgroup: 10:freezer:/
mountinfo: /../.. /sys/fs/cgroup/freezer
/proc/self/cgroup: 10:freezer:/
mountinfo: / /mnt/freezer
cgroup.clone_children freezer.parent_freezing freezer.state tasks
cgroup.procs freezer.self_freezing notify_on_release
3164
2653 # First shell that placed in this cgroup
3164 # Shell started by 'unshare'
14197 # cat(1)
Signed-off-by: Serge Hallyn <serge.hallyn@ubuntu.com>
Tested-by: Michael Kerrisk <mtk.manpages@gmail.com>
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Lots of Idiotic Silly Parentheses is -> that way... What that
condition checks is that there's exactly 32 bytes between the
end of name and the end of entire drectory record.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
... and make that weird ioctl lock directory only shared.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
don't need to lock directory in ->llseek(), either
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Note that lustre has its private mutex protecting directory pagecache;
if they ever remove it, they'll need to be careful with PageChecked()
use.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
use d_alloc_parallel() for sillyunlink/lookup exclusion and
explicit rwsem (nfs_rmdir() being a writer and nfs_call_unlink() -
a reader) for rmdir/sillyunlink one.
That ought to make lookup/readdir/!O_CREAT atomic_open really
parallel on NFS.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
An earlier patch changed lookup side to also net_eq() namespaces after
obtaining a reference on the conntrack, so a single kmemcache can be used.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
We already include netns address in the hash, so we only need to use
net_eq in find_appropriate_src and can then put all entries into
same table.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Will be needed soon when we place all in the same hash table.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/fixes-non-critical
Merge "non urgent auxdata fix for v4.7 merge window" from Tony Lindgren:
Device tree auxdata handling fix that allows a match based on the
compatible string if no exact match based on the IO address is found.
This leaves out the need to patch auxdata for each driver when adding
new SoCs. And it also reprotedly fixes the issue of passing auxdata
to a child if the parent instantiates the child from DT as discussed
in the "[PATCH] of/platform: Allow secondary compatible match in
of_dev_lookup" mailing list thread.
As a minimal use case, let's also convert omap pinctrl auxdatato
use a generic match.
There is no need to get this in to the v4.6-rc cycle and it can wait
for v4.7 merge window. Note that these changes have now been sitting
in Linux next for about two weeks so far as I wanted to make sure no
new issues are popping up.
* tag 'omap-for-v4.7/auxdata-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Simplify auxdata by using the generic match
of/platform: Allow secondary compatible match in of_dev_lookup
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/fixes-non-critical
Merge "omap legacy boot vs dt boot fixes for v4.7 merge window"
from Tony Lindgren:
Legacy booting vs device tree booting fixes for omaps for
v4.7 merge window. These are not considered urgent fixes enough
for the v4.6-rc cycle, but we need them in v4.7 in order to drop
the last remaining board-*.c files for omap3 for v4.8 merge window.
On Nokia N900, we need to pass the MMC slot names for the legacy
user space to work. Let's do that using auxdata as the driver is
setting up things already with the pdata for legacy booting. Then
we can later on discuss if we may want to have some generic binding
describing where the MMC slots are on the device.
N900 also has had the ir-rx51 device driver unusable with multiarch
for a long time. Let's pass the dmtimer data in pdata for the driver
to get it going again. Then once things are working, we can eventually
change the driver to use just hrtimer and PWM framework. The driver
changes will be queued separately.
* tag 'omap-for-v4.7/legacy-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: n900 needs MMC slot names for legacy user space
ARM: OMAP2+: Add more functions to pwm pdata for ir-rx51
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/fixes-non-critical
Merge "Samsung DTS non-critical fixes for v4.7":
1. Fix s5p-mfc driver probe on Exynos542x Peach boards (need to provide MFC
memory banks). On these boards this was broken for long time but
apparently no one enabled this driver till now.
2. Fix creation of debugfs entries for one regulator on Exynos4210
Trats board.
3. Fix probing of max8997 MFD driver (and its children) because
of missing interrupt. Actually the current version of the driver probes
(just without interrupts) but after switching to regmap and regmap-irq,
the interrupt will be mandatory.
* tag 'samsung-fixes-non-critical-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Add interrupt line to MAX8997 PMIC on exynos4210-trats
ARM: dts: exynos: Fix regulator name to avoid forbidden character on exynos4210-trats
ARM: dts: exynos: Add MFC memory banks for Peach boards
ARM: EXYNOS: Properly skip unitialized parent clock in power domain on
|
|
arm-ccn driver uses irq_set_affinity, which is not exported and
hence cannot be built as a module, eventhough we have all the
bits ready. This patch makes use of the exported helper
irq_set_affinity_hint() instead. Also, the __free_irq expects
the affinity_hint to be NULL when we free the irq. So set the
affinity_hint to NULL at clean up.
Now that we can build it as a module, update the Kconfig to
reflect the change.
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
next/drivers
Merge "Reset controller changes for v4.7" from Philipp Zabel:
- add missing stub for device_reset
- add support for OXNAS SoCs
* tag 'reset-for-4.7-2' of git://git.pengutronix.de/git/pza/linux:
reset: Add missing function stub for device_reset
dt-bindings: Add Oxford Semiconductor Reset Controller bindings
reset: Add Oxford Semiconductor Reset Controller driver
|
|
next/soc
Merge "ARM: mediatek: kconfig updates for v4.7" from Matthias Brugger:
Add mt2701 support
* tag 'v4.6-next-kconfig' of https://github.com/mbgg/linux-mediatek:
ARM: mediatek: Add MT2701 config options for mediatek SoCs.
|
|
next/drivers
Merge "ARM: mediatek soc updates for v4.7" from Matthias Brugger:
- re-organize pmic wrapper code for easier and cleaner addiont of new SoCs and pmic wrappers
- add support for pmic wrapper mt6323
- add support for SoC mt2701
- enable gpt6 arch timer on mt7623
* tag 'v4.6-next-soc' of https://github.com/mbgg/linux-mediatek:
ARM: mediatek: enable gpt6 on boot up to make arch timer work on mt7623
soc: mediatek: PMIC wrap: add MT2701/7623 support
soc: mediatek: PMIC wrap: add mt6323 slave support
soc: mediatek: PMIC wrap: add a slave specific struct
soc: mediatek: PMIC wrap: remove pwrap_is_mt8135() and pwrap_is_mt8173()
soc: mediatek: PMIC wrap: move wdt_src into the pmic_wrapper_type struct
soc: mediatek: PMIC wrap: SPI_WRITE needs a different bitmask for MT2701/7623
soc: mediatek: PMIC wrap: WRAP_INT_EN needs a different bitmask for MT2701/7623
soc: mediatek: PMIC wrap: split SoC specific init into callback
soc: mediatek: PMIC wrap: add wrapper callbacks for init_reg_clock
soc: mediatek: PMIC wrap: don't duplicate the wrapper data
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/drivers
Merge "soc/tegra: Add generic PM domain support" from Thierry Reding:
Implements generic PM domain support on top of the existing Tegra power-
gate API. Drivers are thus allowed to move away from the Tegra-specific
API and towards using generic power domains directly.
* tag 'tegra-for-4.7-genpd' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
soc/tegra: pmc: Add generic PM domain support
dt-bindings: Add power domain info for NVIDIA PMC
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/drivers
Merge "usb: host: xhci-tegra: Changes for v4.7-rc1" from Thierry Reding:
This set of patches introduces a driver for the XUSB controller found on
NVIDIA Tegra SoCs. When loaded with a firmware (available via the linux-
firmware repository), it provides an XHCI-compatible interface.
* tag 'tegra-for-4.7-xhci' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
usb: xhci: tegra: Add Tegra210 support
usb: xhci: Add NVIDIA Tegra XUSB controller driver
dt-bindings: usb: xhci-tegra: Add Tegra210 XUSB controller support
dt-bindings: usb: Add NVIDIA Tegra XUSB controller binding
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/drivers
Merge "PCI: tegra: Changes for v4.7-rc1" from Thierry Reding:
These patches update the Tegra PCIe host bridge controller device tree
bindings and driver to cope with per-lane PHYs on Tegra124 and later.
* tag 'tegra-for-4.7-pci' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
PCI: tegra: Support per-lane PHYs
dt-bindings: pci: tegra: Update for per-lane PHYs
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/drivers
Merge "phy: tegra: Changes for v4.7-rc1" from Thierry Reding:
This set of patches adds support for the Tegra XUSB pad controller. The
controller provides a set of pads (lanes) that are used for I/O by other
IP blocks within Tegra SoCs (PCIe, SATA and XUSB).
* tag 'tegra-for-4.7-phy' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
phy: tegra: Add Tegra210 support
phy: Add Tegra XUSB pad controller support
dt-bindings: phy: tegra-xusb-padctl: Add Tegra210 support
dt-bindings: phy: Add NVIDIA Tegra XUSB pad controller binding
phy: core: Allow children node to be overridden
clk: tegra: Add interface to enable hardware control of SATA/XUSB PLLs
|
