| Age | Commit message (Collapse) | Author |
|---|
|
We're initializing pg_offset to 0, setting it immediately, then
reassigning it to 0 again after. The former became unnecessary in
211c17f51f46 ("Fix corners in writepage and btrfs_truncate_page"). The
latter is a leftover that should've been removed in 40f765805f08
("Btrfs: split up __extent_writepage to lower stack usage"). Remove
both.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
ordered->start, ordered->len, and ordered->disk_len correspond to
fi->disk_bytenr, fi->num_bytes, and fi->disk_num_bytes, respectively.
It's confusing to translate between the two naming schemes. Since a
btrfs_ordered_extent is basically a pending btrfs_file_extent_item,
let's make the former use the naming from the latter.
Note that I didn't touch the names in tracepoints just in case there are
scripts depending on the current naming.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Snapshot-aware defrag has been disabled since commit 8101c8dbf624
("Btrfs: disable snapshot aware defrag for now") almost 6 years ago.
Let's remove the dead code. If someone is up to the task of bringing it
back, they can dig it up from git.
This is logically a revert of commit 38c227d87c49 ("Btrfs:
snapshot-aware defrag") except that now we have to clear the
EXTENT_DEFRAG bit to avoid need_force_cow() returning true forever.
The reasons to disable were caused by runtime problems (like long stalls
or memory consumption) on heavily referenced extents (eg. thousands of
snapshots). There were attempts to fix that but never finished.
Current defrag breaks the extent references and some users prefer that
behaviour over the one implemented by snapshot aware (ie. keeping links
for defragmentation). To enable both usecases we'd need to extend
defrag ioctl but let's do that properly from scratch.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ enhance ]
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
We can encode this in the offset parameter: -1 means use the page
offsets, anything else is a valid offset.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Currently, we have two wrappers for __btrfs_lookup_bio_sums():
btrfs_lookup_bio_sums_dio(), which is used for direct I/O, and
btrfs_lookup_bio_sums(), which is used everywhere else. The only
difference is that the _dio variant looks up csums starting at the given
offset instead of using the page index, which isn't actually direct
I/O-specific. Let's clean up the signature and return value of
__btrfs_lookup_bio_sums(), rename it to btrfs_lookup_bio_sums(), and get
rid of the trivial helpers.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
When closing a device, btrfs_close_one_device() first allocates a new
device, copies the device to close's name, replaces it in the dev_list
with the copy and then finally frees it.
This involves two memory allocation, which can potentially fail. As this
code path is tricky to unwind, the allocation failures where handled by
BUG_ON()s.
But this copying isn't strictly needed, all that is needed is resetting
the device in question to it's state it had after the allocation.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
In btrfs_close_one_device we're decrementing the number of open devices
before we're calling btrfs_close_bdev().
As there is no intermediate exit between these points in this function it
is technically OK to do so, but it makes the code a bit harder to understand.
Move both operations closer together and move the decrement step after
btrfs_close_bdev().
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
When you snapshot a subvolume containing a subvolume, you get a
placeholder directory where the subvolume would be. These directories
have their own btrfs_dir_ro_inode_operations.
Al pointed out [1] that these directories can use simple_lookup()
instead of btrfs_lookup(), as they are always empty. Furthermore, they
can use the default generic_permission() instead of btrfs_permission();
the additional checks in the latter don't matter because we can't write
to the directory anyways. Finally, they can use the default
generic_update_time() instead of btrfs_update_time(), as the inode
doesn't exist on disk and doesn't need any special handling.
All together, this means that we can get rid of
btrfs_dir_ro_inode_operations and use simple_dir_inode_operations
instead.
1: https://lore.kernel.org/linux-btrfs/20190929052934.GY26530@ZenIV.linux.org.uk/
Cc: Al Viro <viro@zeniv.linux.org.uk>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ add comment ]
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
We have a user report, that cppcheck is complaining about a possible
NULL-pointer dereference in btrfs_destroy_dev_replace_tgtdev().
We're first dereferencing the 'tgtdev' variable and the later check for
the validity of the pointer with a WARN_ON(!tgtdev);
But all callers of btrfs_destroy_dev_replace_tgtdev() either explicitly
check if 'tgtdev' is non-NULL or directly allocate 'tgtdev', so the
WARN_ON() is impossible to hit. Just remove it to silence the checker's
complains.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=205003
Signed-off-by: Johannes Thumshirn <jth@kernel.org>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
btrfsic_process_superblock() BUG_ON()s if 'state' is NULL. But this can
never happen as the only caller from btrfsic_process_superblock() is
btrfsic_mount() which allocates 'state' some lines above calling
btrfsic_process_superblock() and checks for the allocation to succeed.
Let's just remove the impossible to hit BUG_ON().
Signed-off-by: Johannes Thumshirn <jth@kernel.org>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
A user reports a possible NULL-pointer dereference in
btrfsic_process_superblock(). We are assigning state->fs_info to a local
fs_info variable and afterwards checking for the presence of state.
While we would BUG_ON() a NULL state anyways, we can also just remove
the local fs_info copy, as fs_info is only used once as the first
argument for btrfs_num_copies(). There we can just pass in
state->fs_info as well.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=205003
Signed-off-by: Johannes Thumshirn <jth@kernel.org>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
This is a relic from a time before we had a proper reservation mechanism
and you could end up with really full chunks at chunk allocation time.
This doesn't make sense anymore, so just kill it.
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
We have the space_info, we can just check its flags to see if it's the
system chunk space info.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
It's a simple wrapper over btrfs_panic and is called only once. Just
open code it.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
btrfs_relocate_block_group()
There are two relocation stages but both print the same message. Add the
description of the stage. This can help debugging or provides
informative message to users.
BTRFS info (device dm-5): balance: start -d -m -s
BTRFS info (device dm-5): relocating block group 30408704 flags metadata|dup
BTRFS info (device dm-5): found 2 extents, stage: move data extents
BTRFS info (device dm-5): relocating block group 22020096 flags system|dup
BTRFS info (device dm-5): found 1 extents, stage: move data extents
BTRFS info (device dm-5): relocating block group 13631488 flags data
BTRFS info (device dm-5): found 1 extents, stage: move data extents
BTRFS info (device dm-5): found 1 extents, stage: update data pointers
BTRFS info (device dm-5): balance: ended with status: 0
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
The condition '!ret2' is always true. commit 717beb96d969 ("Btrfs: fix
regression in btrfs_page_mkwrite() from vm_fault_t conversion") left
behind the check after moving this code out of the goto, so remove the
unused condition check.
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Yunfeng Ye <yeyunfeng@huawei.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
level <0 and level >= BTRFS_MAX_LEVEL are already performed upon
extent buffer read by tree checker in btrfs_check_node.
go. As far as 'level <= 0' we are guaranteed that level is '> 0'
because the value of level _before_ reading 'next' is larger than 1
(otherwise we wouldn't have executed that code at all) this in turn
guarantees that 'level' after btrfs_read_buffer is 'level - 1' since
we verify this invariant in:
btrfs_read_buffer
btree_read_extent_buffer_pages
btrfs_verify_level_key
This guarantees that level can never be '<= 0' so the warn on is
never triggered.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
The log_root passed to walk_log_tree is guaranteed to have its
root_key.objectid always be BTRFS_TREE_LOG_OBJECTID. This is by
merit that all log roots of an ordinary root are allocated in
alloc_log_tree which hard-codes objectid to be BTRFS_TREE_LOG_OBJECTID.
In case walk_log_tree is called for a log tree found by btrfs_read_fs_root
in btrfs_recover_log_trees, that function already ensures
found_key.objectid is BTRFS_TREE_LOG_OBJECTID.
No functional changes.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
__btrfs_free_reserved_extent now performs the actions of
btrfs_free_and_pin_reserved_extent. But this name is a bit of a
misnomer, since the extent is not really freed but just pinned. Reflect
this in the new name. No semantics changes.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
__btrfs_free_reserved_extent performs 2 entirely different operations
depending on whether its 'pin' argument is true or false. This patch
lifts the 2nd case (pin is false) into it's sole caller
btrfs_free_reserved_extent. No semantics changes.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
All callers of btrfs_free_reserved_extent (respectively
__btrfs_free_reserved_extent with in set to 0) pass in extents which
have only been reserved but not yet written to. Namely,
* in cow_file_range that function is called only if create_io_em fails
or btrfs_add_ordered_extent fail, both of which happen _before_ any IO
is submitted to the newly reserved range
* in submit_compressed_extents the code flow is similar -
out_free_reserve can be called only before
btrfs_submit_compressed_write which is where any writes to the range
could occur
* btrfs_new_extent_direct also calls btrfs_free_reserved_extent only
if extent_map fails, before any IO is issued
* __btrfs_prealloc_file_range also calls btrfs_free_reserved_extent
in case insertion of the metadata fails
* btrfs_alloc_tree_block again can only be called in case in-memory
operations fail, before any IO is submitted
* btrfs_finish_ordered_io - this is the only caller where discarding
the extent could have a material effect, since it can be called for
an extent which was partially written.
With this change the submission of discards is optimised since discards
are now not being created for extents which are known to not have been
touched on disk.
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
[PROBLEM]
qgroup create/remove code is currently returning EINVAL when the user
tries to create a qgroup on a subvolume without quota enabled. EINVAL is
already being used for too many error scenarios so that is hard to
depict what is the problem.
[FIX]
Currently scrub and balance code return -ENOTCONN when the user tries to
cancel/pause and no scrub or balance is currently running for the
desired subvolume. Do the same here by returning -ENOTCONN when a user
tries to create/delete/assing/list a qgroup on a subvolume without quota
enabled.
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Marcos Paulo de Souza <mpdesouza@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Remove some variables that are set only to be checked later, and never
used.
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Marcos Paulo de Souza <mpdesouza@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Merge btrfs_sysfs_add_fsid() and btrfs_sysfs_add_devices_kobj() functions
as these two are small and they are called one after the other.
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
btrfs_sysfs_add_device() creates the directory
/sys/fs/btrfs/UUID/devices but its function name is misleading. Rename
it to btrfs_sysfs_add_devices_kobj() instead. No functional changes.
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Commit 24bd69cb ("Btrfs: sysfs: add support to add parent for fsid")
added parent argument in preparation to show the seed fsid under the
sprout fsid as in the patch [1] in the mailing list.
[1] Btrfs: sysfs: support seed devices in the sysfs layout
But later this idea was superseded by another idea to rename the fsid as
in the commit f93c39970b1d ("btrfs: factor out sysfs code for updating
sprout fsid").
So we don't need parent argument anymore.
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
The struct member btrfs_device::device_dir_kobj holds the kobj of the
sysfs directory /sys/fs/btrfs/UUID/devices, so rename it from
device_dir_kobj to devices_kobj. No functional changes.
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Make the number of copies explicit even for entries that use the default
0 value for consistency.
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
The table is already used for ncopies, replace open coding of stripes
with the raid_attr value.
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
When using the NO_HOLES feature, if we punch a hole into a file and then
fsync it, there are cases where a subsequent fsync will miss the fact that
a hole was punched, resulting in the holes not existing after replaying
the log tree.
Essentially these cases all imply that, tree-log.c:copy_items(), is not
invoked for the leafs that delimit holes, because nothing changed those
leafs in the current transaction. And it's precisely copy_items() where
we currenly detect and log holes, which works as long as the holes are
between file extent items in the input leaf or between the beginning of
input leaf and the previous leaf or between the last item in the leaf
and the next leaf.
First example where we miss a hole:
*) The extent items of the inode span multiple leafs;
*) The punched hole covers a range that affects only the extent items of
the first leaf;
*) The fsync operation is done in full mode (BTRFS_INODE_NEEDS_FULL_SYNC
is set in the inode's runtime flags).
That results in the hole not existing after replaying the log tree.
For example, if the fs/subvolume tree has the following layout for a
particular inode:
Leaf N, generation 10:
[ ... INODE_ITEM INODE_REF EXTENT_ITEM (0 64K) EXTENT_ITEM (64K 128K) ]
Leaf N + 1, generation 10:
[ EXTENT_ITEM (128K 64K) ... ]
If at transaction 11 we punch a hole coverting the range [0, 128K[, we end
up dropping the two extent items from leaf N, but we don't touch the other
leaf, so we end up in the following state:
Leaf N, generation 11:
[ ... INODE_ITEM INODE_REF ]
Leaf N + 1, generation 10:
[ EXTENT_ITEM (128K 64K) ... ]
A full fsync after punching the hole will only process leaf N because it
was modified in the current transaction, but not leaf N + 1, since it
was not modified in the current transaction (generation 10 and not 11).
As a result the fsync will not log any holes, because it didn't process
any leaf with extent items.
Second example where we will miss a hole:
*) An inode as its items spanning 5 (or more) leafs;
*) A hole is punched and it covers only the extents items of the 3rd
leaf. This resulsts in deleting the entire leaf and not touching any
of the other leafs.
So the only leaf that is modified in the current transaction, when
punching the hole, is the first leaf, which contains the inode item.
During the full fsync, the only leaf that is passed to copy_items()
is that first leaf, and that's not enough for the hole detection
code in copy_items() to determine there's a hole between the last
file extent item in the 2nd leaf and the first file extent item in
the 3rd leaf (which was the 4th leaf before punching the hole).
Fix this by scanning all leafs and punch holes as necessary when doing a
full fsync (less common than a non-full fsync) when the NO_HOLES feature
is enabled. The lack of explicit file extent items to mark holes makes it
necessary to scan existing extents to determine if holes exist.
A test case for fstests follows soon.
Fixes: 16e7549f045d33 ("Btrfs: incompatible format change to remove hole extents")
CC: stable@vger.kernel.org # 4.4+
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Both functions call init_intel_cacheinfo() which computes L2 and L3 cache
sizes from CPUID(4). But then they also call cpu_detect_cache_sizes() a
bit later which computes ->x86_tlbsize and L2 size from CPUID(80000006).
However, the latter call is not needed because
- on these CPUs, CPUID(80000006).EBX for ->x86_tlbsize is reserved
- CPUID(80000006).ECX for the L2 size has the same result as CPUID(4)
Therefore, remove the latter call to simplify the code.
[ bp: Rewrite commit message. ]
Signed-off-by: Tony W Wang-oc <TonyWWang-oc@zhaoxin.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/1579075257-6985-1-git-send-email-TonyWWang-oc@zhaoxin.com
|
|
Monitoring tools that want to find out which resctrl control and monitor
groups a task belongs to must currently read the "tasks" file in every
group until they locate the process ID.
Add an additional file /proc/{pid}/cpu_resctrl_groups to provide this
information:
1) res:
mon:
resctrl is not available.
2) res:/
mon:
Task is part of the root resctrl control group, and it is not associated
to any monitor group.
3) res:/
mon:mon0
Task is part of the root resctrl control group and monitor group mon0.
4) res:group0
mon:
Task is part of resctrl control group group0, and it is not associated
to any monitor group.
5) res:group0
mon:mon1
Task is part of resctrl control group group0 and monitor group mon1.
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Tested-by: Jinshi Chen <jinshi.chen@intel.com>
Link: https://lkml.kernel.org/r/20200115092851.14761-1-yu.c.chen@intel.com
|
|
commit 2db154b3ea8e ("vfs: syscall: Add move_mount(2) to move mounts around")
introduced a new move_mount(2) system call and a corresponding new LSM
security_move_mount hook but did not implement this hook for any existing
LSM. This creates a regression for SELinux with respect to consistent
checking of mounts; the existing selinux_mount hook checks mounton
permission to the mount point path. Provide a SELinux hook
implementation for move_mount that applies this same check for
consistency. In the future we may wish to add a new move_mount
filesystem permission and check as well, but this addresses
the immediate regression.
Fixes: 2db154b3ea8e ("vfs: syscall: Add move_mount(2) to move mounts around")
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Reviewed-by: Ondrej Mosnacek <omosnace@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
|
|
Ido Schimmel says:
====================
mlxsw: Adjust SPAN egress mirroring buffer size handling for Spectrum-2
Jiri says:
For Spectrum-2 the computation of SPAN egress mirroring buffer uses a
different formula. On top of MTU it needs also current port speed. Fix
the computation and also trigger the buffer size set according to PUDE
event, which happens when port speed changes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When PUDE event is handled and the link is up, update the port SPAN
buffer size according to the current speed.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For SPAN egress mirroring buffer size, it is needed to use a different
formula for Spectrum and Spectrum-2. Move the buffer size computation to
ops and implement new formula for Spectrum-2.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Avoid duplication of code that is doing buffsize update and put it into
a separate helper function.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently PTP code queries directly PTYS register for port speed from
work scheduled upon PUDE event. Since the speed needs to be used for
SPAN buffer size computation as well, push the code into a separate
helper.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A compliation error happen when building branch 5.5-rc7
In file included from net/hsr/hsr_main.c:12:0:
net/hsr/hsr_main.h:194:20: error: two or more data types in declaration specifiers
static inline void void hsr_debugfs_rename(struct net_device *dev)
So Removed one void.
Fixes: 4c2d5e33dcd3 ("hsr: rename debugfs file when interface name is changed")
Signed-off-by: xiaofeng.yan <yanxiaofeng7@jd.com>
Acked-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is to fix a serious issue that clock is always disabled
in esdhc_of_set_clock().
Fixes: 1b21a701aed9 ("mmc: sdhci-of-esdhc: fix clock setting for different controller versions")
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Link: https://lore.kernel.org/r/20200120094835.28050-1-yangbo.lu@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The standard SD controller uses two 16-bit registers for
command sending.
0xC: Transfer Mode Register
0xE: Command Register
But the eSDHC controller uses one 32-bit register instead.
0xC: XFERTYPE
For Transfer Mode Register and Command Register writing,
the eSDHC driver will store Transfer Mode Register value in
a variable first. When Command Register writing happens,
driver will directly write a 32-bit value into XFERTYPE
register.
But for Transfer Mode Register reading, driver just returns
a actual value. This may cause issue for some read-modify-write
operations. We should make both reading and write on that variable
for Transfer Mode Register.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Link: https://lore.kernel.org/r/20200117063858.37296-1-yangbo.lu@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
When switching from any MMC speed mode that requires 1.8v
(HS200, HS400 and HS400ES) to High Speed (HS) mode, the system
ends up configured for SDR12 with a 50MHz clock which is an illegal
mode.
This happens because the SDHCI_CTRL_VDD_180 bit in the
SDHCI_HOST_CONTROL2 register is left set and when this bit is
set, the speed mode is controlled by the SDHCI_CTRL_UHS field
in the SDHCI_HOST_CONTROL2 register. The SDHCI_CTRL_UHS field
will end up being set to 0 (SDR12) by sdhci_set_uhs_signaling()
because there is no UHS mode being set.
The fix is to change sdhci_set_uhs_signaling() to set the
SDHCI_CTRL_UHS field to SDR25 (which is the same as HS) for
any switch to HS mode.
This was found on a new eMMC controller that does strict checking
of the speed mode and the corresponding clock rate. It caused the
switch to HS400 mode to fail because part of the sequence to switch
to HS400 requires a switch from HS200 to HS before going to HS400.
This issue was previously fixed by commit c894e33ddc191 ("mmc: sdhci:
Fix incorrect switch to HS mode") and later removed by commit
07bcc411567c ("Revert \"mmc: sdhci: Fix incorrect switch to HS mode\"")
because it caused failures with some SD cards on AM65X systems. The
fix will now be done in a platform specific callback instead of
common sdhci code.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200113210706.11972-7-alcooperx@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The latest Arasan controller first used in the 7216 now supports
CQE so enable this feature.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Link: https://lore.kernel.org/r/20200113210706.11972-6-alcooperx@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Shutdown controller and disable it's clocks to insure max power
savings in S5 on systems that leave power on.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Link: https://lore.kernel.org/r/20200113210706.11972-5-alcooperx@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The new SCMI clock protocol driver does not get probed that early in
boot. Brcmstb drivers typically have the following code when getting
a clock:
priv->clk = devm_clk_get(&pdev->dev, NULL);
if (IS_ERR(priv->clk)) {
dev_err(&pdev->dev, "Clock not found in Device Tree\n");
priv->clk = NULL;
}
This commit changes the driver to do what is below.
priv->clk = devm_clk_get(&pdev->dev, NULL);
if (IS_ERR(priv->clk)) {
if (PTR_ERR(priv->clk) == -EPROBE_DEFER)
return -EPROBE_DEFER;
dev_err(&pdev->dev, "Clock not found in Device Tree\n");
priv->clk = NULL;
}
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Link: https://lore.kernel.org/r/20200113210706.11972-4-alcooperx@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The latest eMMC JEDEC specification version 5.1 added a new
transfer mode, HS400 with enhanced strobe (HS400ES). This mode
will be selected if both the host controller and eMMC device
support it. The latest Arasan 5.1 controller in the 7216a0
supports this mode. The "Host Controller Specification" has
not been updated so the controller register bit used to enable
this mode is not specified and varies the with controller vendor.
The Linux SDHCI driver supplies a callback for enabling HS400ES
mode and that callback will be used to supply a routine that
will set the proper bit in the Arasan Vendor register.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Link: https://lore.kernel.org/r/20200113210706.11972-3-alcooperx@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Add 7216b0 with supports CQE, HS400, HS400-ES and SDR104.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Link: https://lore.kernel.org/r/20200113210706.11972-2-alcooperx@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Currently MMC core disregards host->f_max during card initialization
phase. Obey upper boundary for the clock frequency and skip faster
speeds when they are above the limit.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Link: https://lore.kernel.org/r/f471bceaf237d582d746bd289c4c4f3639cb7b45.1577962382.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
platform_get_irq() will call dev_err() itself on failure,
so there is no need for the driver to also do this.
This is detected by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200116144322.57308-1-yuehaibing@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Fix an issue reported by sparse, since mixed types of parameters are
used on calling dmaengine_prep_slave_sg().
Fixes: 36e1da441fec (mmc: sdhci: add support for using external DMA devices)
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200120033223.897-1-zhang.chunyan@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
