summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2020-01-15Bluetooth: hci_qca: Add QCA Rome power off support to the qca_power_shutdown()Rocky Liao
Current qca_power_shutdown() only supports wcn399x, this patch adds Rome power off support to it. For Rome it just needs to pull down the bt_en GPIO to power off it. This patch also replaces all the power off operation in qca_close() with the unified qca_power_shutdown() call. Signed-off-by: Rocky Liao <rjliao@codeaurora.org> Reviewed-by: Matthias Kaehlcke <mka@chromium.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2020-01-15tcp: fix marked lost packets not being retransmittedPengcheng Yang
When the packet pointed to by retransmit_skb_hint is unlinked by ACK, retransmit_skb_hint will be set to NULL in tcp_clean_rtx_queue(). If packet loss is detected at this time, retransmit_skb_hint will be set to point to the current packet loss in tcp_verify_retransmit_hint(), then the packets that were previously marked lost but not retransmitted due to the restriction of cwnd will be skipped and cannot be retransmitted. To fix this, when retransmit_skb_hint is NULL, retransmit_skb_hint can be reset only after all marked lost packets are retransmitted (retrans_out >= lost_out), otherwise we need to traverse from tcp_rtx_queue_head in tcp_xmit_retransmit_queue(). Packetdrill to demonstrate: // Disable RACK and set max_reordering to keep things simple 0 `sysctl -q net.ipv4.tcp_recovery=0` +0 `sysctl -q net.ipv4.tcp_max_reordering=3` // Establish a connection +0 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3 +0 setsockopt(3, SOL_SOCKET, SO_REUSEADDR, [1], 4) = 0 +0 bind(3, ..., ...) = 0 +0 listen(3, 1) = 0 +.1 < S 0:0(0) win 32792 <mss 1000,sackOK,nop,nop,nop,wscale 7> +0 > S. 0:0(0) ack 1 <...> +.01 < . 1:1(0) ack 1 win 257 +0 accept(3, ..., ...) = 4 // Send 8 data segments +0 write(4, ..., 8000) = 8000 +0 > P. 1:8001(8000) ack 1 // Enter recovery and 1:3001 is marked lost +.01 < . 1:1(0) ack 1 win 257 <sack 3001:4001,nop,nop> +0 < . 1:1(0) ack 1 win 257 <sack 5001:6001 3001:4001,nop,nop> +0 < . 1:1(0) ack 1 win 257 <sack 5001:7001 3001:4001,nop,nop> // Retransmit 1:1001, now retransmit_skb_hint points to 1001:2001 +0 > . 1:1001(1000) ack 1 // 1001:2001 was ACKed causing retransmit_skb_hint to be set to NULL +.01 < . 1:1(0) ack 2001 win 257 <sack 5001:8001 3001:4001,nop,nop> // Now retransmit_skb_hint points to 4001:5001 which is now marked lost // BUG: 2001:3001 was not retransmitted +0 > . 2001:3001(1000) ack 1 Signed-off-by: Pengcheng Yang <yangpc@wangsu.com> Acked-by: Neal Cardwell <ncardwell@google.com> Tested-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-15Bluetooth: hci_bcm: enable IRQ capability from devicetreeGuillaume La Roque
Add support for getting IRQ directly from DT instead of relying on converting a GPIO to IRQ. This is needed for platforms with GPIO controllers that that do not support gpiod_to_irq(). Reviewed-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Guillaume La Roque <glaroque@baylibre.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2020-01-15dt-bindings: net: bluetooth: add interrupts propertiesGuillaume La Roque
add interrupts and interrupt-names as optional properties to support host-wakeup by interrupt properties instead of host-wakeup-gpios. Signed-off-by: Guillaume La Roque <glaroque@baylibre.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2020-01-15Bluetooth: btsdio: Check for valid packet typeLuiz Augusto von Dentz
Check for valid packet type before calling hci_recv_frame which is inline with what other drivers are doing. Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2020-01-15Bluetooth: hci_h5: Add support for ISO packetsLuiz Augusto von Dentz
This enables H5 driver to properly handle ISO packets. Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2020-01-15Bluetooth: hci_h4: Add support for ISO packetsLuiz Augusto von Dentz
This enables H4 driver to properly handle ISO packets. Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2020-01-15Bluetooth: Make use of __check_timeout on hci_sched_leLuiz Augusto von Dentz
This reuse __check_timeout on hci_sched_le following the same logic used hci_sched_acl. Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2020-01-15Bluetooth: monitor: Add support for ISO packetsLuiz Augusto von Dentz
This enables passing ISO packets to the monitor socket. Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2020-01-15Bluetooth: hci_vhci: Add support for ISO packetsLuiz Augusto von Dentz
This make virtual controllers to pass ISO packets around. Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2020-01-15Bluetooth: Add definitions for CIS connectionsLuiz Augusto von Dentz
These adds the HCI definitions for handling CIS connections along with ISO data packets. Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2020-01-15Bluetooth: Implementation of MGMT_OP_SET_BLOCKED_KEYS.Alain Michaud
MGMT command is added to receive the list of blocked keys from user-space. The list is used to: 1) Block keys from being distributed by the device during the ke distribution phase of SMP. 2) Filter out any keys that were previously saved so they are no longer used. Signed-off-by: Alain Michaud <alainm@chromium.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2020-01-15selftests/bpf: Add a test for attaching a bpf fentry/fexit trace to an XDP ↵Eelco Chaudron
program Add a test that will attach a FENTRY and FEXIT program to the XDP test program. It will also verify data from the XDP context on FENTRY and verifies the return code on exit. Signed-off-by: Eelco Chaudron <echaudro@redhat.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Andrii Nakryiko <andriin@fb.com> Link: https://lore.kernel.org/bpf/157909410480.47481.11202505690938004673.stgit@xdp-tutorial
2020-01-15ALSA: seq: Fix racy access for queue timer in proc readTakashi Iwai
snd_seq_info_timer_read() reads the information of the timer assigned for each queue, but it's done in a racy way which may lead to UAF as spotted by syzkaller. This patch applies the missing q->timer_mutex lock while accessing the timer object as well as a slight code change to adapt the standard coding style. Reported-by: syzbot+2b2ef983f973e5c40943@syzkaller.appspotmail.com Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200115203733.26530-1-tiwai@suse.de Signed-off-by: Takashi Iwai <tiwai@suse.de>
2020-01-15tick/common: Touch watchdog in tick_unfreeze() on all CPUsChunyan Zhang
Suspend to IDLE invokes tick_unfreeze() on resume. tick_unfreeze() on the first resuming CPU resumes timekeeping, which also has the side effect of resetting the softlockup watchdog on this CPU. But on the secondary CPUs the watchdog is not reset in the resume / unfreeze() path, which can result in false softlockup warnings on those CPUs depending on the time spent in suspend. Prevent this by clearing the softlock watchdog in the unfreeze path also on the secondary resuming CPUs. [ tglx: Massaged changelog ] Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lore.kernel.org/r/20200110083902.27276-1-chunyan.zhang@unisoc.com
2020-01-15libbpf: Support .text sub-calls relocationsAndrii Nakryiko
The LLVM patch https://reviews.llvm.org/D72197 makes LLVM emit function call relocations within the same section. This includes a default .text section, which contains any BPF sub-programs. This wasn't the case before and so libbpf was able to get a way with slightly simpler handling of subprogram call relocations. This patch adds support for .text section relocations. It needs to ensure correct order of relocations, so does two passes: - first, relocate .text instructions, if there are any relocations in it; - then process all the other programs and copy over patched .text instructions for all sub-program calls. v1->v2: - break early once .text program is processed. Signed-off-by: Andrii Nakryiko <andriin@fb.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Yonghong Song <yhs@fb.com> Cc: Alexei Starovoitov <ast@kernel.org> Link: https://lore.kernel.org/bpf/20200115190856.2391325-1-andriin@fb.com
2020-01-15Fix built-in early-load Intel microcode alignmentJari Ruusu
Intel Software Developer's Manual, volume 3, chapter 9.11.6 says: "Note that the microcode update must be aligned on a 16-byte boundary and the size of the microcode update must be 1-KByte granular" When early-load Intel microcode is loaded from initramfs, userspace tool 'iucode_tool' has already 16-byte aligned those microcode bits in that initramfs image. Image that was created something like this: iucode_tool --write-earlyfw=FOO.cpio microcode-files... However, when early-load Intel microcode is loaded from built-in firmware BLOB using CONFIG_EXTRA_FIRMWARE= kernel config option, that 16-byte alignment is not guaranteed. Fix this by forcing all built-in firmware BLOBs to 16-byte alignment. [ If we end up having other firmware with much bigger alignment requirements, we might need to introduce some method for the firmware to specify it, this is the minimal "just increase the alignment a bit to account for this one special case" patch - Linus ] Signed-off-by: Jari Ruusu <jari.ruusu@gmail.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Fenghua Yu <fenghua.yu@intel.com> Cc: Luis Chamberlain <mcgrof@kernel.org> Cc: stable@kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-01-15Merge branch 'bpf_send_signal_thread'Alexei Starovoitov
Yonghong Song says: ==================== Commit 8b401f9ed244 ("bpf: implement bpf_send_signal() helper") added helper bpf_send_signal() which permits bpf program to send a signal to the current process. The signal may send to any thread of the process. This patch implemented a new helper bpf_send_signal_thread() to send a signal to the thread corresponding to the kernel current task. This helper can simplify user space code if the thread context of bpf sending signal is needed in user space. Please see Patch #1 for details of use case and kernel implementation. Patch #2 added some bpf self tests for the new helper. Changelogs: v2 -> v3: - More simplification for skeleton codes by removing not-needed mmap code and redundantly created tracepoint link. v1 -> v2: - More description for the difference between bpf_send_signal() and bpf_send_signal_thread() in the uapi header bpf.h. - Use skeleton and mmap for send_signal test. ==================== Acked-by: Andrii Nakryiko <andriin@fb.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org>
2020-01-15tools/bpf: Add self tests for bpf_send_signal_thread()Yonghong Song
The test_progs send_signal() is amended to test bpf_send_signal_thread() as well. $ ./test_progs -n 40 #40/1 send_signal_tracepoint:OK #40/2 send_signal_perf:OK #40/3 send_signal_nmi:OK #40/4 send_signal_tracepoint_thread:OK #40/5 send_signal_perf_thread:OK #40/6 send_signal_nmi_thread:OK #40 send_signal:OK Summary: 1/6 PASSED, 0 SKIPPED, 0 FAILED Also took this opportunity to rewrite the send_signal test using skeleton framework and array mmap to make code simpler and more readable. Signed-off-by: Yonghong Song <yhs@fb.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Link: https://lore.kernel.org/bpf/20200115035003.602425-1-yhs@fb.com
2020-01-15bpf: Add bpf_send_signal_thread() helperYonghong Song
Commit 8b401f9ed244 ("bpf: implement bpf_send_signal() helper") added helper bpf_send_signal() which permits bpf program to send a signal to the current process. The signal may be delivered to any threads in the process. We found a use case where sending the signal to the current thread is more preferable. - A bpf program will collect the stack trace and then send signal to the user application. - The user application will add some thread specific information to the just collected stack trace for later analysis. If bpf_send_signal() is used, user application will need to check whether the thread receiving the signal matches the thread collecting the stack by checking thread id. If not, it will need to send signal to another thread through pthread_kill(). This patch proposed a new helper bpf_send_signal_thread(), which sends the signal to the thread corresponding to the current kernel task. This way, user space is guaranteed that bpf_program execution context and user space signal handling context are the same thread. Signed-off-by: Yonghong Song <yhs@fb.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Link: https://lore.kernel.org/bpf/20200115035002.602336-1-yhs@fb.com
2020-01-15xsk: Support allocations of large umemsMagnus Karlsson
When registering a umem area that is sufficiently large (>1G on an x86), kmalloc cannot be used to allocate one of the internal data structures, as the size requested gets too large. Use kvmalloc instead that falls back on vmalloc if the allocation is too large for kmalloc. Also add accounting for this structure as it is triggered by a user space action (the XDP_UMEM_REG setsockopt) and it is by far the largest structure of kernel allocated memory in xsk. Reported-by: Ryan Goodfellow <rgoodfel@isi.edu> Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com> Link: https://lore.kernel.org/bpf/1578995365-7050-1-git-send-email-magnus.karlsson@intel.com
2020-01-15Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/lftan/nios2 Pull arch/nios2 fixlet from Ley Foon Tan: "Update my nios2 maintainer email" * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lftan/nios2: MAINTAINERS: Update Ley Foon Tan's email address
2020-01-15i2c: iop3xx: Fix memory leak in probe error pathKrzysztof Kozlowski
When handling devm_gpiod_get_optional() errors, free the memory already allocated. This fixes Smatch warnings: drivers/i2c/busses/i2c-iop3xx.c:437 iop3xx_i2c_probe() warn: possible memory leak of 'new_adapter' drivers/i2c/busses/i2c-iop3xx.c:442 iop3xx_i2c_probe() warn: possible memory leak of 'new_adapter' Fixes: fdb7e884ad61 ("i2c: iop: Use GPIO descriptors") Reported-by: kbuild test robot <lkp@intel.com> Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2020-01-15Merge tag 'platform-drivers-x86-v5.5-3' of ↵Linus Torvalds
git://git.infradead.org/linux-platform-drivers-x86 Pull x86 platform driver fixes from Andy Shevchenko: - Fix keyboard brightness control for ASUS laptops - Better handling parameters of GPD pocket fan module to avoid thermal shock - Add IDs to PMC platform driver to support Intel Comet Lake - Fix potential dead lock in Mellanox TM FIFO driver and ABI documentation * tag 'platform-drivers-x86-v5.5-3' of git://git.infradead.org/linux-platform-drivers-x86: Documentation/ABI: Add missed attribute for mlxreg-io sysfs interfaces Documentation/ABI: Fix documentation inconsistency for mlxreg-io sysfs interfaces platform/x86: asus-wmi: Fix keyboard brightness cannot be set to 0 platform/x86: intel_pmc_core: update Comet Lake platform driver platform/x86: GPD pocket fan: Allow somewhat lower/higher temperature limits platform/x86: GPD pocket fan: Use default values when wrong modparams are given platform/mellanox: fix potential deadlock in the tmfifo driver platform/x86: intel-ips: Use the correct style for SPDX License Identifier
2020-01-15ALSA: usb-audio: unlock on error in probeDan Carpenter
We need to unlock before we returning on this error path. Fixes: 73ac9f5e5b43 ("ALSA: usb-audio: Add boot quirk for MOTU M Series") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Link: https://lore.kernel.org/r/20200115174604.rhanfgy4j3uc65cx@kili.mountain Signed-off-by: Takashi Iwai <tiwai@suse.de>
2020-01-15Merge branch 'linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6 Pull crypto fix from Herbert Xu: "This fixes a build problem for the hisilicon driver" * 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: crypto: hisilicon/sec2 - Use atomics instead of __sync
2020-01-15soc: ti: k3: add navss ringacc driverGrygorii Strashko
The Ring Accelerator (RINGACC or RA) provides hardware acceleration to enable straightforward passing of work between a producer and a consumer. There is one RINGACC module per NAVSS on TI AM65x SoCs. The RINGACC converts constant-address read and write accesses to equivalent read or write accesses to a circular data structure in memory. The RINGACC eliminates the need for each DMA controller which needs to access ring elements from having to know the current state of the ring (base address, current offset). The DMA controller performs a read or write access to a specific address range (which maps to the source interface on the RINGACC) and the RINGACC replaces the address for the transaction with a new address which corresponds to the head or tail element of the ring (head for reads, tail for writes). Since the RINGACC maintains the state, multiple DMA controllers or channels are allowed to coherently share the same rings as applicable. The RINGACC is able to place data which is destined towards software into cached memory directly. Supported ring modes: - Ring Mode - Messaging Mode - Credentials Mode - Queue Manager Mode TI-SCI integration: Texas Instrument's System Control Interface (TI-SCI) Message Protocol now has control over Ringacc module resources management (RM) and Rings configuration. The corresponding support of TI-SCI Ringacc module RM protocol introduced as option through DT parameters: - ti,sci: phandle on TI-SCI firmware controller DT node - ti,sci-dev-id: TI-SCI device identifier as per TI-SCI firmware spec if both parameters present - Ringacc driver will configure/free/reset Rings using TI-SCI Message Ringacc RM Protocol. The Ringacc driver manages Rings allocation by itself now and requests TI-SCI firmware to allocate and configure specific Rings only. It's done this way because, Linux driver implements two stage Rings allocation and configuration (allocate ring and configure ring) while TI-SCI Message Protocol supports only one combined operation (allocate+configure). Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Reviewed-by: Tero Kristo <t-kristo@ti.com> Tested-by: Keerthy <j-keerthy@ti.com> Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
2020-01-15bindings: soc: ti: add documentation for k3 ringaccGrygorii Strashko
The Ring Accelerator (RINGACC or RA) provides hardware acceleration to enable straightforward passing of work between a producer and a consumer. There is one RINGACC module per NAVSS on TI AM65x and j721e. This patch introduces RINGACC device tree bindings. Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Reviewed-by: Rob Herring <robh@kernel.org> Tested-by: Keerthy <j-keerthy@ti.com> Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
2020-01-15Merge branch 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfsLinus Torvalds
Pull vfs fixes from Al Viro: "Fixes for mountpoint_last() bugs (by converting to use of lookup_last()) and an autofs regression fix from this cycle (caused by follow_managed() breakage introduced in barrier fixes series)" * 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: fix autofs regression caused by follow_managed() changes reimplement path_mountpoint() with less magic
2020-01-15i2c: tegra: Properly disable runtime PM on driver's probe errorDmitry Osipenko
One of the recent Tegra I2C commits made a change that resumes runtime PM during driver's probe, but it missed to put the RPM in a case of error. Note that it's not correct to use pm_runtime_status_suspended because it breaks RPM refcounting. Fixes: 8ebf15e9c869 ("i2c: tegra: Move suspend handling to NOIRQ phase") Cc: <stable@vger.kernel.org> # v5.4+ Tested-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2020-01-15i2c: tegra: Fix suspending in active runtime PM stateDmitry Osipenko
I noticed that sometime I2C clock is kept enabled during suspend-resume. This happens because runtime PM defers dynamic suspension and thus it may happen that runtime PM is in active state when system enters into suspend. In particular I2C controller that is used for CPU's DVFS is often kept ON during suspend because CPU's voltage scaling happens quite often. Fixes: 8ebf15e9c869 ("i2c: tegra: Move suspend handling to NOIRQ phase") Cc: <stable@vger.kernel.org> # v5.4+ Tested-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2020-01-15arm64: Use register field helper in kaslr_requires_kpti()Will Deacon
Rather than open-code the extraction of the E0PD field from the MMFR2 register, we can use the cpuid_feature_extract_unsigned_field() helper instead. Acked-by: Suzuki K Poulose <suzuki.poulose@arm.com> Reviewed-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Will Deacon <will@kernel.org>
2020-01-15arm64: Simplify early check for broken TX1 when KASLR is enabledWill Deacon
Now that the decision to use non-global mappings is stored in a variable, the check to avoid enabling them for the terminally broken ThunderX1 platform can be simplified so that it is only keyed off the MIDR value. Acked-by: Suzuki K Poulose <suzuki.poulose@arm.com> Reviewed-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Will Deacon <will@kernel.org>
2020-01-15arm64: Turn "broken gas inst" into real config optionVladimir Murzin
Use the new 'as-instr' Kconfig macro to define CONFIG_BROKEN_GAS_INST directly, making it available everywhere. Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com> [will: Drop redundant 'y if' logic] Signed-off-by: Will Deacon <will@kernel.org>
2020-01-15cgroup: Prevent double killing of css when enabling threaded cgroupMichal Koutný
The test_cgcore_no_internal_process_constraint_on_threads selftest when running with subsystem controlling noise triggers two warnings: > [ 597.443115] WARNING: CPU: 1 PID: 28167 at kernel/cgroup/cgroup.c:3131 cgroup_apply_control_enable+0xe0/0x3f0 > [ 597.443413] WARNING: CPU: 1 PID: 28167 at kernel/cgroup/cgroup.c:3177 cgroup_apply_control_disable+0xa6/0x160 Both stem from a call to cgroup_type_write. The first warning was also triggered by syzkaller. When we're switching cgroup to threaded mode shortly after a subsystem was disabled on it, we can see the respective subsystem css dying there. The warning in cgroup_apply_control_enable is harmless in this case since we're not adding new subsys anyway. The warning in cgroup_apply_control_disable indicates an attempt to kill css of recently disabled subsystem repeatedly. The commit prevents these situations by making cgroup_type_write wait for all dying csses to go away before re-applying subtree controls. When at it, the locations of WARN_ON_ONCE calls are moved so that warning is triggered only when we are about to misuse the dying css. Reported-by: syzbot+5493b2a54d31d6aea629@syzkaller.appspotmail.com Reported-by: Christian Brauner <christian.brauner@ubuntu.com> Signed-off-by: Michal Koutný <mkoutny@suse.com> Signed-off-by: Tejun Heo <tj@kernel.org>
2020-01-15workqueue: remove workqueue_work event classDaniel Jordan
The trace event class workqueue_work now has only one consumer, so get rid of it. No functional change. Signed-off-by: Daniel Jordan <daniel.m.jordan@oracle.com> Cc: Tejun Heo <tj@kernel.org> Cc: Lai Jiangshan <jiangshanlai@gmail.com> Cc: linux-kernel@vger.kernel.org Signed-off-by: Tejun Heo <tj@kernel.org>
2020-01-15workqueue: add worker function to workqueue_execute_end tracepointDaniel Jordan
It's surprising that workqueue_execute_end includes only the work when its counterpart workqueue_execute_start has both the work and the worker function. You can't set a tracing filter or trigger based on the function, and postprocessing scripts interested in specific functions are harder to write since they have to remember the work from _start and match it up with the same field in _end. Add the function name, taking care to use the copy stashed in the worker since the work is no longer safe to touch. Signed-off-by: Daniel Jordan <daniel.m.jordan@oracle.com> Cc: Tejun Heo <tj@kernel.org> Cc: Lai Jiangshan <jiangshanlai@gmail.com> Cc: linux-kernel@vger.kernel.org Signed-off-by: Tejun Heo <tj@kernel.org>
2020-01-15cgroup: fix function name in commentChen Zhou
Function name cgroup_rstat_cpu_pop_upated() in comment should be cgroup_rstat_cpu_pop_updated(). Signed-off-by: Chen Zhou <chenzhou10@huawei.com> Signed-off-by: Tejun Heo <tj@kernel.org>
2020-01-15null_blk: Fix zone write handlingDamien Le Moal
null_zone_write() only allows writing empty and implicitly opened zones. Writing to closed and explicitly opened zones must also be allowed and the zone condition must be transitioned to implicit open if the zone is not explicitly opened already. Fixes: da644b2cc1a4 ("null_blk: add zone open, close, and finish support") Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2020-01-15Merge branch 'topic/equal' of ↵Mark Brown
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator into asoc-5.6
2020-01-15arm64: Use a variable to store non-global mappings decisionMark Brown
Refactor the code which checks to see if we need to use non-global mappings to use a variable instead of checking with the CPU capabilities each time, doing the initial check for KPTI early in boot before we start allocating memory so we still avoid transitioning to non-global mappings in common cases. Since this variable always matches our decision about non-global mappings this means we can also combine arm64_kernel_use_ng_mappings() and arm64_unmap_kernel_at_el0() into a single function, the variable simply stores the result and the decision code is elsewhere. We could just have the users check the variable directly but having a function makes it clear that these uses are read-only. The result is that we simplify the code a bit and reduces the amount of code executed at runtime. Signed-off-by: Mark Brown <broonie@kernel.org> Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com> Signed-off-by: Will Deacon <will@kernel.org>
2020-01-15arm64: Don't use KPTI where we have E0PDMark Brown
Since E0PD is intended to fulfil the same role as KPTI we don't need to use KPTI on CPUs where E0PD is available, we can rely on E0PD instead. Change the check that forces KPTI on when KASLR is enabled to check for E0PD before doing so, CPUs with E0PD are not expected to be affected by meltdown so should not need to enable KPTI for other reasons. Since E0PD is a system capability we will still enable KPTI if any of the CPUs in the system lacks E0PD, this will rewrite any global mappings that were established in systems where some but not all CPUs support E0PD. We may transiently have a mix of global and non-global mappings while booting since we use the local CPU when deciding if KPTI will be required prior to completing CPU enumeration but any global mappings will be converted to non-global ones when KPTI is applied. KPTI can still be forced on from the command line if required. Signed-off-by: Mark Brown <broonie@kernel.org> Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com> Signed-off-by: Will Deacon <will@kernel.org>
2020-01-15arm64: Factor out checks for KASLR in KPTI code into separate functionMark Brown
In preparation for integrating E0PD support with KASLR factor out the checks for interaction between KASLR and KPTI done in boot context into a new function kaslr_requires_kpti(), in the process clarifying the distinction between what we do in boot context and what we do at runtime. Signed-off-by: Mark Brown <broonie@kernel.org> Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com> Signed-off-by: Will Deacon <will@kernel.org>
2020-01-15arm64: Add initial support for E0PDMark Brown
Kernel Page Table Isolation (KPTI) is used to mitigate some speculation based security issues by ensuring that the kernel is not mapped when userspace is running but this approach is expensive and is incompatible with SPE. E0PD, introduced in the ARMv8.5 extensions, provides an alternative to this which ensures that accesses from userspace to the kernel's half of the memory map to always fault with constant time, preventing timing attacks without requiring constant unmapping and remapping or preventing legitimate accesses. Currently this feature will only be enabled if all CPUs in the system support E0PD, if some CPUs do not support the feature at boot time then the feature will not be enabled and in the unlikely event that a late CPU is the first CPU to lack the feature then we will reject that CPU. This initial patch does not yet integrate with KPTI, this will be dealt with in followup patches. Ideally we could ensure that by default we don't use KPTI on CPUs where E0PD is present. Signed-off-by: Mark Brown <broonie@kernel.org> Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com> [will: Fixed typo in Kconfig text] Signed-off-by: Will Deacon <will@kernel.org>
2020-01-15dmaengine: plx-dma: Implement descriptor submissionLogan Gunthorpe
On prep, a spin lock is taken and the next entry in the circular buffer is filled. On submit, the valid bit is set in the hardware descriptor and the lock is released. The DMA engine is started (if it's not already running) when the client calls dma_async_issue_pending(). Signed-off-by: Logan Gunthorpe <logang@deltatee.com> Link: https://lore.kernel.org/r/20200103212021.2881-4-logang@deltatee.com Signed-off-by: Vinod Koul <vkoul@kernel.org>
2020-01-15dmaengine: plx-dma: Implement hardware initialization and cleanupLogan Gunthorpe
Allocate DMA coherent memory for the ring of DMA descriptors and program the appropriate hardware registers. A tasklet is created which is triggered on an interrupt to process all the finished requests. Additionally, any remaining descriptors are aborted when the hardware is removed or the resources freed. Use an RCU pointer to synchronize PCI device unbind. Signed-off-by: Logan Gunthorpe <logang@deltatee.com> Link: https://lore.kernel.org/r/20200103212021.2881-3-logang@deltatee.com Signed-off-by: Vinod Koul <vkoul@kernel.org>
2020-01-15dmaengine: plx-dma: Introduce PLX DMA engine PCI driver skeletonLogan Gunthorpe
Some PLX Switches can expose DMA engines via extra PCI functions on the upstream port. Each function will have one DMA channel. This patch is just the core PCI driver skeleton and dma engine registration. Signed-off-by: Logan Gunthorpe <logang@deltatee.com> Link: https://lore.kernel.org/r/20200103212021.2881-2-logang@deltatee.com Signed-off-by: Vinod Koul <vkoul@kernel.org>
2020-01-15regulator fix for "regulator: core: Add regulator_is_equal() helper"Stephen Rothwell
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Link: https://lore.kernel.org/r/20200115120258.0e535fcb@canb.auug.org.au Acked-by: Marek Vasut <marex@denx.de> Signed-off-by: Mark Brown <broonie@kernel.org>
2020-01-15usb: musb: remove dummy driver musb_am335x.cBin Liu
Since commit 0782e8572ce4 ("ARM: dts: Probe am335x musb with ti-sysc"), the dummy driver musb_am335x.c is no longer needed, let's drop it. Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Bin Liu <b-liu@ti.com> Link: https://lore.kernel.org/r/20200115132547.364-26-b-liu@ti.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-15usb: musb: davinci: Convert to use GPIO descriptorLinus Walleij
The DaVinci MUSB glue contains an optional GPIO line to control VBUS power, convert this to use a GPIO descriptor and augment the EVM board file to provide this descriptor. I can't get this driver to compile properly and it depends on broken but when I didn get it to compile brokenly, it did at least not complain about THIS code being broken so I don't think I broke the driver any more than what it already is. I did away with the ifdefs that do not work with multiplatform anyway so the day someone decides to resurrect the code, the path to get it working should be easier as well since DaVinci is now multiplatform. Cc: Sekhar Nori <nsekhar@ti.com> Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com> Cc: Tony Lindgren <tony@atomide.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> [b-liu@ti.com: fixed one instance still ref to global variable vbus_state] Signed-off-by: Bin Liu <b-liu@ti.com> Link: https://lore.kernel.org/r/20200115132547.364-25-b-liu@ti.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
generated by cgit (git 2.34.1) at 2025-09-21 01:04:19 +0000