| Age | Commit message (Collapse) | Author |
|---|
|
FW starts using legacy power table command (0x77) for device wide power
settings. Currently this command contains only option flags field.
It can configure the following: CAM (Continuous Active Mode) and
POWER_SAVE_ENABLE debug option. Send this command when firmware is
loaded - D0 and D3.
Note: Setting this command is important to avoid unwanted FW behavior.
It particularly fixes a bug when a device does not drop to low power
after disassociation from AP.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This should really not happen. If it does, restarting is the
only way to recover since the driver and the firmware might
very well be out of sync. Moreover, iwl_op_mode_nic_error
will print data that might help debugging.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Single shared antenna devices need a special LUT.
Address this need.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In loose BT Coex scheme, the aggregation size doesn't need to
be limited.
To avoid triggering it, remove a lockdep assertion - we need
to compute the AMPDU size limit from rate control code which
can't take mvm->mutex. This means that there is a race but in
the worst case, we will have a wrong AMPDU size limit which
is not a big issue.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
To avoid casting skb->dev into hdev, just let the drivers provide
the hdev directly when calling hci_recv_frame() function.
This patch also fixes up all drivers to provide the hdev.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
The function h4_check_data_len() is actually not used. So just
remove it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
Fengguang Wu, Oleg Nesterov and Peter Zijlstra tracked down
a kernel crash to a GCC bug: GCC miscompiles certain 'asm goto'
constructs, as outlined here:
http://gcc.gnu.org/bugzilla/show_bug.cgi?id=58670
Implement a workaround suggested by Jakub Jelinek.
Reported-and-tested-by: Fengguang Wu <fengguang.wu@intel.com>
Reported-by: Oleg Nesterov <oleg@redhat.com>
Reported-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Suggested-by: Jakub Jelinek <jakub@redhat.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
This reverts commit 81b5c7bc8de3e6f63419139c2fc91bf81dea8a7d.
Adding drm/i915 into the vga arbiter chain means that X (in a piece of
well-meant paranoia) will do a get/put on the vga decoding around
_every_ accel call down into the ddx. Which results in some nice
performance disasters [1]. This really breaks userspace, by disabling
DRI for everyone, and stops OpenGL from working, this isn't limited
to just the i915 but both the integrated and discrete GPUs on
multi-gpu systems, in other words this causes untold worlds of pain,
Ville tried to come up with a Great Hack to fiddle the required VGA
I/O ops behind everyone's back using stop_machine, but that didn't
really work out [2]. Given that we're fairly late in the -rc stage for
such games let's just revert this all.
One thing we might want to keep is to delay the disabling of the vga
decoding until the fbdev emulation and the fbcon screen is set up. If
we kill vga mem decoding beforehand fbcon can end up with a white
square in the top-left corner it tried to save from the vga memory for
a seamless transition. And we have bug reports on older platforms
which seem to match these symptoms.
But again that's something to play around with in -next.
References: [1] http://lists.x.org/archives/xorg-devel/2013-September/037763.html
References: [2] http://www.spinics.net/lists/intel-gfx/msg34062.html
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
is done"
This reverts commit 6e1b4fdad5157bb9e88777d525704aba24389bee.
This is part of a revert due to a userspace breakage, better explained in the revert of 1a1a4cbf4906a13c0c377f708df5d94168e7b582.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
commit 9f00b2e7cf241fa389733d41b615efdaa2cb0f5b
bridge: only expire the mdb entry when query is received
changed the mdb expiration timer to be armed only when QUERY is
received. Howerver, this causes issues in an environment where
the multicast server socket comes and goes very fast while a client
is trying to send traffic to it.
The root cause is a race where a sequence of LEAVE followed by REPORT
messages can race against QUERY messages generated in response to LEAVE.
The QUERY ends up starting the expiration timer, and that timer can
potentially expire after the new REPORT message has been received signaling
the new join operation. This leads to a significant drop in multicast
traffic and possible complete stall.
The solution is to have REPORT messages update the expiration timer
on entries that already exist.
CC: Cong Wang <xiyou.wangcong@gmail.com>
CC: Herbert Xu <herbert@gondor.apana.org.au>
CC: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
into drm-fixes
Regression fixes for audio and UVD, several hang fixes,
some DPM fixes.
* 'drm-fixes-3.12' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: re-enable sw ACR support on pre-DCE4
drm/radeon/dpm: disable bapm on TN asics
drm/radeon: improve soft reset on CIK
drm/radeon: improve soft reset on SI
drm/radeon/dpm: off by one in si_set_mc_special_registers()
drm/radeon/dpm/btc: off by one in btc_set_mc_special_registers()
drm/radeon: forever loop on error in radeon_do_test_moves()
drm/radeon: fix hw contexts for SUMO2 asics
drm/radeon: fix typo in CP DMA register headers
drm/radeon/dpm: disable multiple UVD states
drm/radeon: use hw generated CTS/N values for audio
drm/radeon: fix N/CTS clock matching for audio
drm/radeon: use 64-bit math to calculate CTS values for audio (v2)
drm/edid: catch kmalloc failure in drm_edid_to_speaker_allocation
|
|
Free memory allocated to edma_desc when failing to allocate slot.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Commit 4981c4dc194efb18f0e9a02f1b43e926f2f0d2bb (DMA: shdma: switch DT mode to
use configuration data from a match table) added a new parameter to set_slave()
method but unfortunately got merged later than commit c4f6c41ba790bbbfcebb4c47a
(dma: add driver for R-Car HPB-DMAC), so that the HPB-DMAC driver retained the
old prototype which caused this warning:
drivers/dma/sh/rcar-hpbdma.c:485: warning: initialization from incompatible
pointer type
The newly added parameter is used to override DMA slave address from 'struct
hpb_dmae_slave_config', so we have to add the 'slave_addr' field to 'struct
hpb_dmae_chan', conditionally assign it in set_slave() method, and return in
slave_addr() method.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Commit c1c63a14f4f2419d093acd7164eccdff315baa86 (DMA: shdma: switch to managed
resource allocation) got rid of shdma_free_irq() but unfortunately got merged
later than commit c4f6c41ba790bbbfcebb4c47a709ac8ff1fe1af9 (dma: add driver for
R-Car HPB-DMAC), so that the HPB-DMAC driver retained the calls and got broken:
drivers/dma/sh/rcar-hpbdma.c: In function `hpb_dmae_alloc_chan_resources':
drivers/dma/sh/rcar-hpbdma.c:435: error: implicit declaration of function
`shdma_free_irq'
Fix this compilation error by removing the remaining shdma_free_irq() calls.
Reported-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
When doing space balance and subvolume destroy at the same time, we met
the following oops:
kernel BUG at fs/btrfs/relocation.c:2247!
RIP: 0010: [<ffffffffa04cec16>] prepare_to_merge+0x154/0x1f0 [btrfs]
Call Trace:
[<ffffffffa04b5ab7>] relocate_block_group+0x466/0x4e6 [btrfs]
[<ffffffffa04b5c7a>] btrfs_relocate_block_group+0x143/0x275 [btrfs]
[<ffffffffa0495c56>] btrfs_relocate_chunk.isra.27+0x5c/0x5a2 [btrfs]
[<ffffffffa0459871>] ? btrfs_item_key_to_cpu+0x15/0x31 [btrfs]
[<ffffffffa048b46a>] ? btrfs_get_token_64+0x7e/0xcd [btrfs]
[<ffffffffa04a3467>] ? btrfs_tree_read_unlock_blocking+0xb2/0xb7 [btrfs]
[<ffffffffa049907d>] btrfs_balance+0x9c7/0xb6f [btrfs]
[<ffffffffa049ef84>] btrfs_ioctl_balance+0x234/0x2ac [btrfs]
[<ffffffffa04a1e8e>] btrfs_ioctl+0xd87/0x1ef9 [btrfs]
[<ffffffff81122f53>] ? path_openat+0x234/0x4db
[<ffffffff813c3b78>] ? __do_page_fault+0x31d/0x391
[<ffffffff810f8ab6>] ? vma_link+0x74/0x94
[<ffffffff811250f5>] vfs_ioctl+0x1d/0x39
[<ffffffff811258c8>] do_vfs_ioctl+0x32d/0x3e2
[<ffffffff811259d4>] SyS_ioctl+0x57/0x83
[<ffffffff813c3bfa>] ? do_page_fault+0xe/0x10
[<ffffffff813c73c2>] system_call_fastpath+0x16/0x1b
It is because we returned the error number if the reference of the root was 0
when doing space relocation. It was not right here, because though the root
was dead(refs == 0), but the space it held still need be relocated, or we
could not remove the block group. So in this case, we should return the root
no matter it is dead or not.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
|
|
Now we don't drop all the deleted snapshots/subvolumes before the space
balance. It means we have to relocate the space which is held by the dead
snapshots/subvolumes. So we must into them into fs radix tree, or we would
forget to commit the change of them when doing transaction commit, and it
would corrupt the metadata.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
|
|
Liu fixed part of this problem and unfortunately I steered him in slightly the
wrong direction and so didn't completely fix the problem. The problem is we
limit the size of the delalloc range we are looking for to max bytes and then we
try to lock that range. If we fail to lock the pages in that range we will
shrink the max bytes to a single page and re loop. However if our first page is
inside of the delalloc range then we will end up limiting the end of the range
to a period before our first page. This is illustrated below
[0 -------- delalloc range --------- 256mb]
[page]
So find_delalloc_range will return with delalloc_start as 0 and end as 128mb,
and then we will notice that delalloc_start < *start and adjust it up, but not
adjust delalloc_end up, so things go sideways. To fix this we need to not limit
the max bytes in find_delalloc_range, but in find_lock_delalloc_range and that
way we don't end up with this confusion. Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
|
|
btrfs_rename was using the root of the old dir instead of the root of the new
dir when checking for a hash collision, so if you tried to move a file into a
subvol it would freak out because it would see the file you are trying to move
in its current root. This fixes the bug where this would fail
btrfs subvol create test1
btrfs subvol create test2
mv test1 test2.
Thanks to Chris Murphy for catching this,
Cc: stable@vger.kernel.org
Reported-by: Chris Murphy <lists@colorremedies.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
|
|
Commit c0f04d88e46d ("bcache: Fix flushes in writeback mode") was fixing
a reported data corruption bug, but it seems some last minute
refactoring or rebasing introduced a null pointer deref.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.10
Reported-by: Gabriel de Perthuis <g2p.code@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fix from Guenter Roeck:
"Fix root cause of crash/error seen in applesmc driver"
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (applesmc) Always read until end of data
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild
Pull kbuild fix from Michal Marek:
"Here is an ARM Makefile fix that you even acked. After nobody wanted
to take it, it ended up in the kbuild tree"
* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
arm, kbuild: make "make install" not depend on vmlinux
|
|
The return value of hci_send_frame() is never checked. So just make
this function void and print an error when the hdev->send driver
callback returns a negative value.
Having the error printed is actually an improvement over the
current situation where any driver error just gets ignored.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
The hdev parameter of hci_send_frame must be always valid. If the hdev
is not valid, it would not even make it to this stage. The callers
will have already accessed hdev at that point many times.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
The assignement of skb->dev is done all over the place. So it makes it
hard to eventually get rid of it. Move it all in one central place so
it gets assigned right before calling hdev->send driver callback.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
The smp.h header file is only used internally by the bluetooth.ko
module and is not a public API. So make it local to the core
Bluetooth module.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
The a2mp.h header file is only used internally by the bluetooth.ko
module and is not a public API. So make it local to the core
Bluetooth module.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
The amp.h header file is only used internally by the bluetooth.ko
module and is not a public API. So make it local to the core
Bluetooth module.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
Pull watchdog fix from Wim Van Sebroeck:
"Make sure that the hpwdt driver will not load auxilary iLO devices"
* git://www.linux-watchdog.org/linux-watchdog:
watchdog: hpwdt: Patch to ignore auxilary iLO devices
|
|
Useful for locating buggy drivers on kernel oops.
It may add dozens of new lines to boot dmesg. DEBUG_KOBJECT_RELEASE is
hopefully only enabled in debug kernels (like maybe the Fedora rawhide
one, or at developers), so being a bit more verbose is likely ok.
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch is to prevent hpwdt from loading on any auxilary iLO devices defined
after the initial (or main) iLO device. All auxilary iLO devices will have a
subsystem device ID set to 0x1979 in order for hpwdt to differentiate between
the two types.
Signed-off-by: Thomas Mingarelli <thomas.mingarelli@hp.com>
Tested-by: Lisa Mitchell <lisa.mitchell@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Since there is no use of hdev->ioctl by any Bluetooth driver since
ever, so just lets remove it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
The btmrvl_ioctl() function is not used and thus remove it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
The dtl1_hci_ioctl() function is not used and thus remove it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
The btuart_hci_ioctl() function is not used and thus remove it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
The bt3c_hci_ioctl() function is not used and thus remove it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
The bluecard_hci_ioctl() function is not used and thus remove it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
The bfusb_ioctl() function is not used and thus remove it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
The legacy ioctls for device specific commands including inquiry are
not support by AMP controllers. So just reject them right away instead
of trying to send the HCI command and wait for failure from the
actual hardware.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
When changing the alternate setting for the ISOC endpoints, use the
hci_conn_num() helper function to count currently established SCO
and eSCO connections and store the the value. This avoids direct
access to the connection hash.
In addition use the stored value instead accessing the connection
hash over and over again.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
When checking for the current number of LE connections, use
hci_conn_num() function instead of a full blown lookup within
the connection hash or direct access of the counters.
In the case of re-enabling advertising, it is more useful to
check for any connection attempt or existing connection.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
The function declaration goes over 80 characters, so break it down.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random
Pull /dev/random changes from Ted Ts'o:
"These patches are designed to enable improvements to /dev/random for
non-x86 platforms, in particular MIPS and ARM"
* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
random: allow architectures to optionally define random_get_entropy()
random: run random_int_secret_init() run after all late_initcalls
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-next
Jeff Kirsher says:
====================
This series contains updates to i40e only.
Alex provides the majority of the patches against i40e, where he does
cleanup of the Tx and RX queues and to align the code with the known
good Tx/Rx queue code in the ixgbe driver.
Anjali provides an i40e patch to update link events to not print to
the log until the device is administratively up.
Catherine provides a patch to update the driver version.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In commit 634fb979e8f ("inet: includes a sock_common in request_sock")
I forgot that the two ports in sock_common do not have same byte order :
skc_dport is __be16 (network order), but skc_num is __u16 (host order)
So sparse complains because ir_loc_port (mapped into skc_num) is
considered as __u16 while it should be __be16
Let rename ir_loc_port to ireq->ir_num (analogy with inet->inet_num),
and perform appropriate htons/ntohs conversions.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull kvm fixes from Paolo Bonzini:
"Fixes for 3.12-rc5: two old PPC bugs and one new (3.12-rc2) x86 bug"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
kvm: ppc: booke: check range page invalidation progress on page setup
KVM: PPC: Book3S HV: Fix typo in saving DSCR
KVM: nVMX: fix shadow on EPT
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"This is all driver updates, mostly fixes for error handling paths
except for the s3c64xx and hspi fixes for trying to use runtime PM
before it is enabled and the pxa2xx fix for interactions between power
management and interrupt handling"
* tag 'spi-v3.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: atmel: Fix incorrect error path
spi/hspi: fixup Runtime PM enable timing
spi/s3c64xx: Ensure runtime PM is enabled prior to registration
spi/clps711x: drop clk_put for devm_clk_get in spi_clps711x_probe()
spi: fix return value check in dspi_probe()
spi: mpc512x: fix error return code in mpc512x_psc_spi_do_probe()
spi: clps711x: Don't call kfree() after spi_master_put/spi_unregister_master
spi/pxa2xx: check status register as well to determine if the device is off
|
|
Allow architectures which have a disabled get_cycles() function to
provide a random_get_entropy() function which provides a fine-grained,
rapidly changing counter that can be used by the /dev/random driver.
For example, an architecture might have a rapidly changing register
used to control random TLB cache eviction, or DRAM refresh that
doesn't meet the requirements of get_cycles(), but which is good
enough for the needs of the random driver.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@vger.kernel.org
|
|
Pull MTD fixes from Brian Norris:
- fix a small memory leak in some new ONFI code
- account for additional odd variations of Micron SPI flash
Acked by David Woodhouse.
* tag 'for-linus-20131008' of git://git.infradead.org/linux-mtd:
mtd: m25p80: Fix 4 byte addressing mode for Micron devices.
mtd: nand: fix memory leak in ONFI extended parameter page
|
|
This fixes "lost interrupt" problems that occurred on SPI-based systems.
cw1200_irq_handler() expects the hwbus to be locked, but on the
SPI-path, that lock wasn't taken (unlike in the SDIO-path, where the
generic SDIO-code takes care of acquiring the lock).
Cc: stable@vger.kernel.org
Signed-off-by: David Mosberger <davidm@egauge.net>
Signed-off-by: Solomon Peachy <pizza@shaftnet.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
An error in calculating the offset in an skb causes the driver to read
essential device info from the wrong locations. The main effect is that
automatic gain calculations are nonsense.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [2.6.39+]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
