| Age | Commit message (Collapse) | Author |
|---|
|
Check memory allocation failure and return -ENOMEM in such a case, as
already done few lines below for another memory allocation.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit e0429362ab15
("usb: Add device quirk for Logitech HD Pro Webcams C920 and C930e")
introduced quirk to workaround an issue with some Logitech webcams.
Apparently model C920-C has the same issue so applying
the same quirk as well.
See aforementioned commit message for detailed explanation of the problem.
Signed-off-by: Dmitry Fleytman <dmitry@daynix.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add support for the SuperSpeed Link Layer test case TD.7.34
which requires the operator to place the port into compliance
mode, and to subsequently bring it out via reset. Historically
according to the (now deprecated) USB 3.0 specification a
SuperSpeed host downstream port would automatically transition
to Compliance mode from the Polling state if LFPS polling times
out. However the language in USB 3.1 as well as xHCI 1.1 states
it may be required to explicitly enable this transition. For
such hosts this is done by sending a SET_FEATURE(PORT_LINK_STATE)
with the state set to Compliance to the root hub port.
Similar to the other supported commands, to do this via sysfs:
echo > /sys/bus/usb/devices/2-0\:1.0/enable_compliance
According to xHCI 1.1 section 4.19.1.2.4.1, this enables the
transition to compliance mode upon LFPS timeout. Note that this
can only be issued when the port is in disconnected state. And
in order to disable this behavior on subsequent transitions, a
warm reset should be issued. So add another entry to do that:
echo > /sys/bus/usb/devices/2-0\:1.0/warm_reset
In general these attributes can also be useful for other USB
SuperSpeed compliance tests such as electrical and eye diagram
testing which require CPn patterns to be transmitted.
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
To perform SuperSpeed compliance testing the port should first
be placed into compliance mode. For xHCI 1.0 and prior this
transition happens automatically when the port is in Training
and encounters an LFPS timeout. Thus running compliance tests
against a test appliance may simply just work by simply plugging
in to the downstream port.
However starting with xHCI 1.1 the transition from Polling.LFPS
to compliance mode may be disabled by default and needs to be
explicitly enabled by writing to the PLS field of the PORTSC
register, which sets an internal 'CTE' (Compliance Transition
Enabled) flag so that the port will perform the transition the
next time it encounters LFPS timeout. Whether this is disabled or
not is determined by the 'CTC' (Compliance Transition Capability)
bit in the HCCPARAMS2 capability register.
In order to allow a test operator to change this if needed, allow
a test driver (such as drivers/usb/misc/lvstest.c) to send a
SET_FEATURE(PORT_LINK_STATE) control message to the root hub to
update the link state prior to connecting to the port. Subsequently,
placing the port in warm reset would then disable the flag.
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The following commit cause a regression on ATI chipsets.
'commit e788787ef4f9 ("usb:xhci:Add quirk for Certain
failing HP keyboard on reset after resume")'
This causes pinfo->smbus_dev to be wrongly set to NULL on
systems with the ATI chipset that this function checks for first.
Added conditional check for AMD chipsets to avoid the overwriting
pinfo->smbus_dev.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Fixes: e788787ef4f9 ("usb:xhci:Add quirk for Certain
failing HP keyboard on reset after resume")
cc: Nehal Shah <Nehal-bakulchandra.Shah@amd.com>
cc: <stable@vger.kernel.org>
Signed-off-by: Sandeep Singh <Sandeep.Singh@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Corsair Strafe RGB keyboard has trouble to initialize:
[ 1.679455] usb 3-6: new full-speed USB device number 4 using xhci_hcd
[ 6.871136] usb 3-6: unable to read config index 0 descriptor/all
[ 6.871138] usb 3-6: can't read configurations, error -110
[ 6.991019] usb 3-6: new full-speed USB device number 5 using xhci_hcd
[ 12.246642] usb 3-6: unable to read config index 0 descriptor/all
[ 12.246644] usb 3-6: can't read configurations, error -110
[ 12.366555] usb 3-6: new full-speed USB device number 6 using xhci_hcd
[ 17.622145] usb 3-6: unable to read config index 0 descriptor/all
[ 17.622147] usb 3-6: can't read configurations, error -110
[ 17.742093] usb 3-6: new full-speed USB device number 7 using xhci_hcd
[ 22.997715] usb 3-6: unable to read config index 0 descriptor/all
[ 22.997716] usb 3-6: can't read configurations, error -110
Although it may work after several times unpluging/pluging:
[ 68.195240] usb 3-6: new full-speed USB device number 11 using xhci_hcd
[ 68.337459] usb 3-6: New USB device found, idVendor=1b1c, idProduct=1b20
[ 68.337463] usb 3-6: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 68.337466] usb 3-6: Product: Corsair STRAFE RGB Gaming Keyboard
[ 68.337468] usb 3-6: Manufacturer: Corsair
[ 68.337470] usb 3-6: SerialNumber: 0F013021AEB8046755A93ED3F5001941
Tried three quirks: USB_QUIRK_DELAY_INIT, USB_QUIRK_NO_LPM and
USB_QUIRK_DEVICE_QUALIFIER, user confirmed that USB_QUIRK_DELAY_INIT alone
can workaround this issue. Hence add the quirk for Corsair Strafe RGB.
BugLink: https://bugs.launchpad.net/bugs/1678477
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make this const as it is only used during a copy operation.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use more compact of_property_read_bool() calls for the boolean properties
instead of of_find_property() calls in of_usb_host_tpl_support() and
of_usb_update_otg_caps().
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
vm_operations_struct are not supposed to change at runtime.
All functions working with const vm_operations_struct.
So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Refactor code in order to avoid identical code for different branches.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
While running reboot tests w/ a specific set of USB devices (and
slub_debug enabled), I found that once every few hours my device would
be crashed with a stack that looked like this:
[ 14.012445] BUG: spinlock bad magic on CPU#0, modprobe/2091
[ 14.012460] lock: 0xffffffc0cb055978, .magic: ffffffc0, .owner: cryption contexts: %lu/%lu
[ 14.012460] /1025536097, .owner_cpu: 0
[ 14.012466] CPU: 0 PID: 2091 Comm: modprobe Not tainted 4.4.79 #352
[ 14.012468] Hardware name: Google Kevin (DT)
[ 14.012471] Call trace:
[ 14.012483] [<....>] dump_backtrace+0x0/0x160
[ 14.012487] [<....>] show_stack+0x20/0x28
[ 14.012494] [<....>] dump_stack+0xb4/0xf0
[ 14.012500] [<....>] spin_dump+0x8c/0x98
[ 14.012504] [<....>] spin_bug+0x30/0x3c
[ 14.012508] [<....>] do_raw_spin_lock+0x40/0x164
[ 14.012515] [<....>] _raw_spin_lock_irqsave+0x64/0x74
[ 14.012521] [<....>] __wake_up+0x2c/0x60
[ 14.012528] [<....>] async_completed+0x2d0/0x300
[ 14.012534] [<....>] __usb_hcd_giveback_urb+0xc4/0x138
[ 14.012538] [<....>] usb_hcd_giveback_urb+0x54/0xf0
[ 14.012544] [<....>] xhci_irq+0x1314/0x1348
[ 14.012548] [<....>] usb_hcd_irq+0x40/0x50
[ 14.012553] [<....>] handle_irq_event_percpu+0x1b4/0x3f0
[ 14.012556] [<....>] handle_irq_event+0x4c/0x7c
[ 14.012561] [<....>] handle_fasteoi_irq+0x158/0x1c8
[ 14.012564] [<....>] generic_handle_irq+0x30/0x44
[ 14.012568] [<....>] __handle_domain_irq+0x90/0xbc
[ 14.012572] [<....>] gic_handle_irq+0xcc/0x18c
Investigation using kgdb() found that the wait queue that was passed
into wake_up() had been freed (it was filled with slub_debug poison).
I analyzed and instrumented the code and reproduced. My current
belief is that this is happening:
1. async_completed() is called (from IRQ). Moves "as" onto the
completed list.
2. On another CPU, proc_reapurbnonblock_compat() calls
async_getcompleted(). Blocks on spinlock.
3. async_completed() releases the lock; keeps running; gets blocked
midway through wake_up().
4. proc_reapurbnonblock_compat() => async_getcompleted() gets the
lock; removes "as" from completed list and frees it.
5. usbdev_release() is called. Frees "ps".
6. async_completed() finally continues running wake_up(). ...but
wake_up() has a pointer to the freed "ps".
The instrumentation that led me to believe this was based on adding
some trace_printk() calls in a select few functions and then using
kdb's "ftdump" at crash time. The trace follows (NOTE: in the trace
below I cheated a little bit and added a udelay(1000) in
async_completed() after releasing the spinlock because I wanted it to
trigger quicker):
<...>-2104 0d.h2 13759034us!: async_completed at start: as=ffffffc0cc638200
mtpd-2055 3.... 13759356us : async_getcompleted before spin_lock_irqsave
mtpd-2055 3d..1 13759362us : async_getcompleted after list_del_init: as=ffffffc0cc638200
mtpd-2055 3.... 13759371us+: proc_reapurbnonblock_compat: free_async(ffffffc0cc638200)
mtpd-2055 3.... 13759422us+: async_getcompleted before spin_lock_irqsave
mtpd-2055 3.... 13759479us : usbdev_release at start: ps=ffffffc0cc042080
mtpd-2055 3.... 13759487us : async_getcompleted before spin_lock_irqsave
mtpd-2055 3.... 13759497us!: usbdev_release after kfree(ps): ps=ffffffc0cc042080
<...>-2104 0d.h2 13760294us : async_completed before wake_up(): as=ffffffc0cc638200
To fix this problem we can just move the wake_up() under the ps->lock.
There should be no issues there that I'm aware of.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make this const as it is only stored in the type field of a device
structure, which is const.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since the discussion is not settled yet for the EMAC, and that the release
in getting really close, let's revert the changes for now, and we'll
reintroduce them later.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Since the discussion is not settled yet for the EMAC, and that the release
in getting really close, let's revert the changes for now, and we'll
reintroduce them later.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
This binding still doesn't please everyone, and we're getting far too
close from the release to allow it to reach a stable version.
Let's remove it until the discussion settles down.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The memory reserved to dump the ID of the xfrm state includes a padding
byte in struct xfrm_usersa_id added by the compiler for alignment. To
prevent the heap info leak, memset(0) the sa_id before filling it.
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Fixes: d51d081d6504 ("[IPSEC]: Sync series - user")
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
The memory reserved to dump the expired xfrm state includes padding
bytes in struct xfrm_user_expire added by the compiler for alignment. To
prevent the heap info leak, memset(0) the remainder of the struct.
Initializing the whole structure isn't needed as copy_to_user_state()
already takes care of clearing the padding bytes within the 'state'
member.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
The memory reserved to dump the ID of the xfrm state includes a padding
byte in struct xfrm_usersa_id added by the compiler for alignment. To
prevent the heap info leak, memset(0) the whole struct before filling
it.
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Fixes: 0603eac0d6b7 ("[IPSEC]: Add XFRMA_SA/XFRMA_POLICY for delete notification")
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
The memory reserved to dump the xfrm offload state includes padding
bytes of struct xfrm_user_offload added by the compiler for alignment.
Add an explicit memset(0) before filling the buffer to avoid the heap
info leak.
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Fixes: d77e38e612a0 ("xfrm: Add an IPsec hardware offloading API")
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
The musb_dsps driver is special in that the parent (glue) device's
driver is accessing registers mapped by the child. The clock is however
shared and is managed by the grandparent device.
Since commit 869c59782981 ("usb: musb: dsps: add support for suspend and
resume") the dsps driver has been accessing these registers as part of
suspend and resume.
The parent driver obviously cannot runtime resume the child during
system suspend and is currently relying on the fact that the child will
be RPM_ACTIVE throughout suspend. The suspend implementation also makes
sure to check that the child is indeed present (and hence the clock
enabled) before accessing the registers.
Let's add an explicit runtime resume of the glue device itself to enable
the clock before doing the register accesses in case these assumptions ever
change (i.e. if the child is left runtime suspended).
Note that the glue-timer cancellation is moved after the child-presence
check to keep error handling simple. This should be fine as the timer is
not setup until the controller is being registered and at that time
glue->musb and its driver data have already been initialised.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Daniel Mack <zonque@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make sure that the controller is runtime resumed when system suspending
to avoid an external abort when accessing the interrupt registers:
Unhandled fault: external abort on non-linefetch (0x1008) at 0xd025840a
...
[<c05481a4>] (musb_default_readb) from [<c0545abc>] (musb_disable_interrupts+0x84/0xa8)
[<c0545abc>] (musb_disable_interrupts) from [<c0546b08>] (musb_suspend+0x38/0xb8)
[<c0546b08>] (musb_suspend) from [<c04a57f8>] (platform_pm_suspend+0x3c/0x64)
This is easily reproduced on a BBB by enabling the peripheral port only
(as the host port may enable the shared clock) and keeping it
disconnected so that the controller is runtime suspended. (Well, you
would also need to the not-yet-merged am33xx-suspend patches by Dave
Gerlach to be able to suspend the BBB.)
This is a regression that was introduced by commit 1c4d0b4e1806 ("usb:
musb: Remove pm_runtime_set_irq_safe") which allowed the parent glue
device to runtime suspend and thereby exposed a couple of older issues:
Register accesses without explicitly making sure the controller is
runtime resumed during suspend was first introduced by commit c338412b5ded
("usb: musb: unconditionally save and restore the context on suspend")
in 3.14.
Commit a1fc1920aaaa ("usb: musb: core: make sure musb is in RPM_ACTIVE on
resume") later started setting the RPM status to active during resume,
and this was also implicitly relying on the parent always being active.
Since commit 71723f95463d ("PM / runtime: print error when activating a
child to unactive parent") this now also results in the following
warning:
musb-hdrc musb-hdrc.0: runtime PM trying to activate child device
musb-hdrc.0 but parent (47401400.usb) is not active
This patch has been verified on 4.13-rc2, 4.12 and 4.9 using a BBB
(the dsps glue would always be active also in 4.8).
Fixes: c338412b5ded ("usb: musb: unconditionally save and restore the context on suspend")
Fixes: a1fc1920aaaa ("usb: musb: core: make sure musb is in RPM_ACTIVE on resume")
Fixes: 1c4d0b4e1806 ("usb: musb: Remove pm_runtime_set_irq_safe")
Cc: stable <stable@vger.kernel.org> # 4.8+
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Daniel Mack <zonque@gmail.com>
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The fifo memory allocation in mode_2_cfg[] doesn't utilize all the 4KB
memory.
Increse some endpoint fifo buffers to fully use all the 4KB memory. Now
we can support more webcam usecases on DA8xx.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There are multiple places in usb core or controller driver which returns
-EMSGSIZE when a class driver queueing urb failed, so the "Message too
long" log doesn't help much for understanding the error.
Let the musb driver to specifically print a error message when
musb_urb_enqueue() returns -EMSGSIZE.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Print an error message with qh maxpacket size and hb_mult when hwep
allocation failed, so we have a better idea why it is failed.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add helper function musb_ep_xfertype_string() to return the ep transfer
type string.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-next
Peter writes:
Chipidea changes for v4.14-rc1
- Add chipidea support at Nvidia SoCs
- Improvement for extcon support
- Some code refines
|
|
This reverts commit d0bdff0db809 ("staging: Fix build issues with new
binder API"), because commit e38361d032f1 ("ARM: 8091/2: add get_user()
support for 8 byte types") has added the 64bit __get_user_asm_*
implementation.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make this const as it is only used in a copy operation.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This results in a nice cleanup, and fixes link errors when fbdev support
is disabled.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Adding __printf verification can help avoid format/argument mismatches.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
1. Remove module_init()/module_exit() macroes and
visorbus_register_visor_driver/visorbus_unregister_visor_driver
functions.
2. Replace with a short module_driver macro
Signed-off-by: Alex Briskin <br.shurik@gmail.com>
Acked-by: David Kershner <david.kershner@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
"hdr" can't be NULL. We take skb->data which is non-NULL and add an
offset to get "hdr".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove "struct pt_regs *" parameter from interrupt handlers, since
it is no longer passed to interrupt handlers. Also, convert return
types to irqreturn_t.
Additionally, move DIO_irq_handler variable into the setup_GPIO
function, as it's not used outside of this function.
Signed-off-by: Cihangir Akturk <cakturk@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This printk doesn't really add anything worthwhile.
Signed-off-by: Shurong Zhang <zhang_shurong@foxmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The call to _rtl_dbg_trace via macro HALMAC_RT_TRACE will trigger a null
pointer deference on the null driver_adapter. Fix this by assigning
driver_adapter earlier to halmac_adapter->driver_adapter before the tracing
call so that a non-null driver_adapter is passed instead.
Detected by CoverityScan, CID#1454613 ("Explicit null dereferenced")
Fixes: 938a0447f094 ("staging: r8822be: Add code for halmac sub-driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A memory leak of eeprom_map occurs if the call to halmac_eeprom_parser_88xx
fails. Fix this by kfree'ing it before returning.
Detected by CoverityScan, CID#1454569 ("Resource leak")
Fixes: 938a0447f094 ("staging: r8822be: Add code for halmac sub-driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The obd_init_checks() function can either return -EOVERFLOW or -EINVAL
but we accidentally ignore -EINVAL returns.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The copy_from_user() function returns the number of bytes which we
weren't able to copy. We don't want to return that to the user but
instead we want to return -EFAULT.
Fixes: d7e09d0397e8 ("staging: add Lustre file system client support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We recently changed from using obd_ioctl_popdata() to calling
copy_to_user() directly. This if statement was supposed to be deleted
but it was over looked. "err" is zero at this point so it means we
return success.
Fixes: b03679f6a41a ("staging: lustre: uapi: remove obd_ioctl_popdata() wrapper")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We want the binder fix in here as well for testing and merge issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
calling memcpy immediately after memset with the same region of memory
makes memset redundant.
Build successfully.
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The changes in this commit are also being sent to the main rtlwifi
drivers in wireless-next; however, these changes will also be useful for
any debugging of r8822be before it gets moved into the main tree.
Use debugfs to dump register and btcoex status, and also write registers
and h2c.
We create topdir in /sys/kernel/debug/rtlwifi/, and use the MAC address
as subdirectory with several entries to dump mac_reg, bb_reg, rf_reg etc.
An example is
/sys/kernel/debug/rtlwifi/00-11-22-33-44-55-66/mac_0
This change permits examination of device registers in a dynamic manner,
a feature not available with the current debug mechanism.
We use seq_file to replace RT_TRACE to dump status, then we can use 'cat'
to access btcoex's status through debugfs.
(i.e. /sys/kernel/debug/rtlwifi/00-11-22-33-44-55-66/btcoex)
Other related changes are
1. implement btc_disp_dbg_msg() to access btcoex's common status.
2. remove obsolete field bt_exist
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Smatch is distrustful of the "capab" value and marks it as user
controlled. I think it actually comes from the firmware? Anyway, I
looked at other drivers and they added a bounds check and it seems like
a harmless thing to have so I have added it here as well.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch is created to solve the following coding style issue reported
by the checkpatch script.
CHECK: spaces preffered around that '&' (ctx:VxV)
Signed-off-by: Janani Sankara Babu <jananis37@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch solves the following warning shown by the checkpatch script
WARNING: Comparisons should place the constants on the right side of
the test
Signed-off-by: Janani Sankara Babu <jananis37@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When the devfreq_add_device fails to register deivce, the memory
leak of devfreq instance happen. So, this patch fix the memory
leak issue. Before freeing the devfreq instance checks whether
devfreq instance is NULL or not because the device_unregister()
frees the devfreq instance when jumping to the 'err_init'.
It is to prevent the duplicate the kfee(devfreq).
Cc: stable@vger.kernel.org
Fixes: ac4b281176a5 ("PM / devfreq: fix duplicated kfree on devfreq pointer")
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
The devfreq ues the OPP library to handle the voltage and frequency
for the device basically. This patch adds the dependency on CONFIG_PM_OPP
in order to prevent either the build break or the unknow behavior.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
THe devfreq_update_stats() updates the 'struct devfreq_dev_status'
in order to get current status of devfreq device. It is only used
for the governors.
This patch moves the devfreq_update_stats() into devfreq directory.
Signed-off-by: Chanwoo Choi <cwchoi00@gmail.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
|
|
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: linux-pm@vger.kernel.org
|
