| Age | Commit message (Collapse) | Author |
|---|
|
Give it a few tries, then exit. Prevents a possible endless loop
situation.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Both lirc_imon and lirc_sasem were causing gcc to complain about the
possible use of uninitialized variables.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The hdpvr's IR part, in short, sucks. As observed with a usb traffic
sniffer, the Windows software for it uses a polling interval of 405ms.
Its still not behaving as well as I'd like even with this change, but
this inches us closer and closer to that point...
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The new hauppauge key tables use both device code button code.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This keymap were used for the Hauppauge Black remote controller
only. It also contains some keycodes not found there. As the
Hauppauge Black is now part of the hauppauge keymap, just remove
it.
Also, remove the modprobe hacks to select between the Gray
and the Black versions of the remote controller as:
- Both are supported by default by the keymap;
- If the user just wants one keyboard supported,
it is just a matter of changing the keymap via
the userspace tool (ir-keytable), removing
the keys that he doesn't desire. As ir-keytable
auto-loads the keys via udev, this is better than
obscure modprobe parameters.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
|
|
The rc-hauppauge-new map is a messy thing, as it bundles 3
different remote controllers as if they were just one,
discarding the address byte. Also, some key maps are wrong.
With the conversion to the new rc-core, it is likely that
most of the devices won't be working properly, as the i2c
driver and the raw decoders are now providing 16 bits for
the remote, instead of just 8.
delete mode 100644 drivers/media/rc/keymaps/rc-hauppauge-new.c
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
|
|
There are two "hauppauge-new" keymaps, one with protocol
unknown, and the other with the protocol marked accordingly.
However, both tables are miss-named.
Also, the old rc-hauppauge-new is broken, as it mixes
three different controllers as if they were just one.
This patch solves half of the problem by renaming the
correct keycode table as just rc-hauppauge. This table
contains the codes for the four different types of
remote controllers found on Hauppauge cards, properly
mapped with their different addresses.
create mode 100644 drivers/media/rc/keymaps/rc-hauppauge.c
delete mode 100644 drivers/media/rc/keymaps/rc-rc5-hauppauge-new.c
[Jarod: fix up RC_MAP_HAUPPAUGE defines]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
|
|
The keys for the old black were messed with the ones for the
hauppauge grey. Fix it.
Also, fixes some keycodes and order the keys according with
the way they appear inside the remote controller.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
|
|
Hans borrowed me an old Black Hauppauge RC. Thanks to that, we
can fix the RC5 table for Hauppauge.
Thanks-to: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
|
|
Adds the old grey remote controller to Hauppauge table.
Hans borrowed me an old gray Hauppauge RC. Thanks to that, we
can fix the RC5 table for Hauppauge.
Thanks-to: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
|
|
One of the remotes has a picture available at:
http://lirc.sourceforge.net/remotes/leadtek/Y04G0004.jpg
As there's one variant with a set direction keys plus vol/chann
keys, and the same table is used for both models, change it to
represent all keys, avoiding the usage of weird function keys.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
|
|
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
|
|
This driver uses an app-specific keymap for one of the tables. This
is wrong. Instead, use the standard keycodes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
|
|
This driver uses an app-specific keymap for one of the tables. This
is wrong. Instead, use the standard keycodes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
|
|
Using xev and testing the "Windows" key on a normal keyboard, it
is mapped as KEY_LEFTMETA. So, as this is the standard code for
it, use it, instead of a generic, meaningless KEY_PROG1.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
|
|
Those KEY_PROG[n] keys were used on places where the developer
didn't know for sure what key should be used. On several cases,
using KEY_RED, KEY_GREEN, KEY_YELLOW would be enough. On others,
there are specific keys for that already.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
|
|
Each keyboard map were using a different definition for
the Source/Video Source key.
Behold Columbus were the only one using KEY_PROPS.
As we want to standardize those keys at X11 and at
userspace applications, we need to use just one code
for it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
|
|
On a few places, KEY_MHP were used for snapshots. However, KEY_CAMERA
is used for it on all the other keyboards that have a snapshot/Picture
button.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
|
|
Update the TODO.lirc_zilog based on what has been completed. Also revised
the development plan for lirc_zilog to not try and split Tx/Rx for one IR
transceiver unit between lirc_zilog and ir-kbd-i2c, since that would be a
ref-counting nightmare.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The total sequence of messages emitted by the ir_porbe() calls
for a transceiver's two i2c_clients was confusing. Clean it up a bit.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Lock the i2c_client pointers and prevent i2c_client removal when
lirc_zilog is perfoming a series of operations that require valid
i2c_client pointers.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This is a major change to add pointer reference counting for
struct IR, struct IR_tx, and struct IR_rx object instances.
This ref counting gets lirc_zilog closer to gracefully handling
bridge drivers and hot-unplugged USB devices disappearing out from
under lirc_zilog when the /dev/lircN node is still open. (mutexes
to protect the i2c_client pointers in struct IR_tx and struct IR_rx
still need to be added.)
This reference counting also helps lirc_zilog clean up properly
when the i2c_clients disappear.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
ir_probe() makes a number of constant assignments into the lirc_driver
object after copying in a template. Make better use of the template.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Always allocate a lirc_buffer object, instead of just upon setup of
the Rx i2c_client. If we do not allocate a lirc_buffer object, because
we are not handling the Rx i2c_client, lirc_dev will allocate its own
lirc_buffer anyway and not tell us about its location.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Remove the rx->buf_lock that protected the rx->buf lirc_buffer. The
underlying operations on the objects within the lirc_buffer are already
protected by spinlocks, or the objects are constant (e.g. chunk_size).
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
There is no need to take the rx->buf_lock in the the poll() function
as all the underling calls made on objects in the rx->buf lirc_buffer object
are protected by spinlocks.
Corrected a bad error return value in poll(): return POLLERR instead
of -ENODEV.
Added some comments to poll() for when, in the future, I forget what
poll() and poll_wait() are supposed to do.
[Jarod: minor debug spew fix]
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
lirc_zilog had its own llseek stub that returned -ESPIPE. Get rid of
it and use the kernel's no_llseek() and nonseekable_open() functions
instead.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The open count is simply used for deciding if the Rx polling thread
needs to poll the IR chip for userspace. Simplify the manipulation
of the open count by using an atomic_t and not requiring a lock
The polling thread errantly didn't try to take the lock anyway.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The set_use_inc() and set_use_dec() functions tried to lock
the underlying bridge driver device instance in memory by
changing the use count on the device's i2c_clients. This
worked for PCI devices (ivtv, cx18, bttv). It doesn't
work for hot-pluggable usb devices (pvrusb2 and hdpvr).
With usb device instances, the driver may get locked into
memory, but the unplugged hardware is gone.
The set_use_inc() set_use_dec() functions also tried to have
lirc_zilog change its own module refernce count, which is
racy and not guaranteed to work. The lirc_dev module does
actually perform proper module ref count manipulation on the
lirc_zilog module, so there is need for lirc_zilog to
attempt a buggy module get on itself anyway.
lirc_zilog also errantly called these functions on itself
in open() and close(), but lirc_dev did that already too.
So let's just gut the bodies of the set_use_*() functions,
and remove the extra calls to them from within lirc_zilog.
Proper reference counting of the struct IR, IR_rx, and IR_tx
objects -- to handle the case when the underlying
bttv, ivtv, cx18, hdpvr, or pvrusb2 bridge driver module or
device instance goes away -- will be added in subsequent
patches.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This reverts commit 8090232a237ab62e22307fc060097da1a283dd66 and
adds an additional check for ir->tx == NULL.
The user may need us to handle an RX only unit. Apparently
there are TV capture units in existence with Rx only wiring
and/or RX only firmware for the on-board Zilog Z8 IR unit.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Make the hdpvr's i2c master implementation more closely mirror that of
the pvrusb2 driver. Currently makes no significant difference in IR
reception behavior with ir-kbd-i2c (i.e., it still sucks).
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Reported-by: Daniel Burr <dburr@topcon.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Recent zerocopy work in the 9P VirtIO transport maps and pins
user buffers into kernel memory for the server to work on them.
Since the user process can initiate this kind of pinning with a simple
read/write call, thousands of IO threads initiated by the user process can
hog the system resources and could result into denial of service.
This patch introduces flow control to avoid that extreme scenario.
The ceiling limit to avoid denial of service attacks is set to relatively
high (nr_free_pagecache_pages()/4) so that it won't interfere with
regular usage, but can step in extreme cases to limit the total system
hang. Since we don't have a global structure to accommodate this variable,
I choose the virtio_chan as the home for this.
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Reviewed-by: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
|
|
Without this fix, even if a file is opened in O_APPEND mode, data will be
written at current file position instead of end of file.
Signed-off-by: M. Mohan Kumar <mohan@in.ibm.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
|
|
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
|
|
Given that the sprious wake-ups are common, we need to move the
condition setting right next to the wake_up(). After setting the condition
to req->status = REQ_STATUS_RCVD, sprious wakeups may cause the
virtqueue back on the free list for someone else to use.
This may result in kernel panic while relasing the pinned pages
in p9_release_req_pages().
Also rearranged the while loop in req_done() for better redability.
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
|
|
Process may wait to get space on VirtIO ring to send a transaction to
VirtFS server. Current code just does a conditional wake_up() which
means only one process will be woken up even if multiple processes
are waiting.
This fix makes the wake_up unconditional. Hence we won't have any
processes waiting for-ever.
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
|
|
Lina reported that if throttle limits are initially very high and then
dropped, then no new bio might be dispatched for a long time. And the
reason being that after dropping the limits we don't reset the existing
slice and do the rate calculation with new low rate and account the bios
dispatched at high rate. To fix it, reset the slice upon rate change.
https://lkml.org/lkml/2011/3/10/298
Another problem with very high limit is that we never queued the
bio on throtl service tree. That means we kept on extending the
group slice but never trimmed it. Fix that also by regulary
trimming the slice even if bio is not being queued up.
Reported-by: Lina Lu <lulina_nuaa@foxmail.com>
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
Add the new static inline and use the same
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
|
|
We don't need writeback fid if we are only doing O_RDONLY open
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
|
|
Older version of protocol don't support tsyncfs operation.
So for them force a O_SYNC flag on the server
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
|
|
convert vmtruncate usage to truncate_setsize. We also writeback
all dirty pages before doing 9p operations and on success call truncate_setsize.
This ensure that we continue sanely on failed truncate on the server. The
disadvantage is that we are now going to write back the content that get
thrown away later as a part of truncate.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
|
|
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
|
|
Without this we can cause reclaim allocation in writepage.
[ 3433.448430] =================================
[ 3433.449117] [ INFO: inconsistent lock state ]
[ 3433.449117] 2.6.38-rc5+ #84
[ 3433.449117] ---------------------------------
[ 3433.449117] inconsistent {RECLAIM_FS-ON-W} -> {IN-RECLAIM_FS-R} usage.
[ 3433.449117] kswapd0/505 [HC0[0]:SC0[0]:HE1:SE1] takes:
[ 3433.449117] (iprune_sem){+++++-}, at: [<ffffffff810ebbab>] shrink_icache_memory+0x45/0x2b1
[ 3433.449117] {RECLAIM_FS-ON-W} state was registered at:
[ 3433.449117] [<ffffffff8107fe5f>] mark_held_locks+0x52/0x70
[ 3433.449117] [<ffffffff8107ff02>] lockdep_trace_alloc+0x85/0x9f
[ 3433.449117] [<ffffffff810d353d>] slab_pre_alloc_hook+0x18/0x3c
[ 3433.449117] [<ffffffff810d3fd5>] kmem_cache_alloc+0x23/0xa2
[ 3433.449117] [<ffffffff8127be77>] idr_pre_get+0x2d/0x6f
[ 3433.449117] [<ffffffff815434eb>] p9_idpool_get+0x30/0xae
[ 3433.449117] [<ffffffff81540123>] p9_client_rpc+0xd7/0x9b0
[ 3433.449117] [<ffffffff815427b0>] p9_client_clunk+0x88/0xdb
[ 3433.449117] [<ffffffff811d56e5>] v9fs_evict_inode+0x3c/0x48
[ 3433.449117] [<ffffffff810eb511>] evict+0x1f/0x87
[ 3433.449117] [<ffffffff810eb5c0>] dispose_list+0x47/0xe3
[ 3433.449117] [<ffffffff810eb8da>] evict_inodes+0x138/0x14f
[ 3433.449117] [<ffffffff810d90e2>] generic_shutdown_super+0x57/0xe8
[ 3433.449117] [<ffffffff810d91e8>] kill_anon_super+0x11/0x50
[ 3433.449117] [<ffffffff811d4951>] v9fs_kill_super+0x49/0xab
[ 3433.449117] [<ffffffff810d926e>] deactivate_locked_super+0x21/0x46
[ 3433.449117] [<ffffffff810d9e84>] deactivate_super+0x40/0x44
[ 3433.449117] [<ffffffff810ef848>] mntput_no_expire+0x100/0x109
[ 3433.449117] [<ffffffff810f0aeb>] sys_umount+0x2f1/0x31c
[ 3433.449117] [<ffffffff8102c87b>] system_call_fastpath+0x16/0x1b
[ 3433.449117] irq event stamp: 192941
[ 3433.449117] hardirqs last enabled at (192941): [<ffffffff81568dcf>] _raw_spin_unlock_irq+0x2b/0x30
[ 3433.449117] hardirqs last disabled at (192940): [<ffffffff810b5f97>] shrink_inactive_list+0x290/0x2f5
[ 3433.449117] softirqs last enabled at (188470): [<ffffffff8105fd65>] __do_softirq+0x133/0x152
[ 3433.449117] softirqs last disabled at (188455): [<ffffffff8102d7cc>] call_softirq+0x1c/0x28
[ 3433.449117]
[ 3433.449117] other info that might help us debug this:
[ 3433.449117] 1 lock held by kswapd0/505:
[ 3433.449117] #0: (shrinker_rwsem){++++..}, at: [<ffffffff810b52e2>] shrink_slab+0x38/0x15f
[ 3433.449117]
[ 3433.449117] stack backtrace:
[ 3433.449117] Pid: 505, comm: kswapd0 Not tainted 2.6.38-rc5+ #84
[ 3433.449117] Call Trace:
[ 3433.449117] [<ffffffff8107fbce>] ? valid_state+0x17e/0x191
[ 3433.449117] [<ffffffff81036896>] ? save_stack_trace+0x28/0x45
[ 3433.449117] [<ffffffff81080426>] ? check_usage_forwards+0x0/0x87
[ 3433.449117] [<ffffffff8107fcf4>] ? mark_lock+0x113/0x22c
[ 3433.449117] [<ffffffff8108105f>] ? __lock_acquire+0x37a/0xcf7
[ 3433.449117] [<ffffffff8107fc0e>] ? mark_lock+0x2d/0x22c
[ 3433.449117] [<ffffffff81081077>] ? __lock_acquire+0x392/0xcf7
[ 3433.449117] [<ffffffff810b14d2>] ? determine_dirtyable_memory+0x15/0x28
[ 3433.449117] [<ffffffff81081a33>] ? lock_acquire+0x57/0x6d
[ 3433.449117] [<ffffffff810ebbab>] ? shrink_icache_memory+0x45/0x2b1
[ 3433.449117] [<ffffffff81567d85>] ? down_read+0x47/0x5c
[ 3433.449117] [<ffffffff810ebbab>] ? shrink_icache_memory+0x45/0x2b1
[ 3433.449117] [<ffffffff810ebbab>] ? shrink_icache_memory+0x45/0x2b1
[ 3433.449117] [<ffffffff810b5385>] ? shrink_slab+0xdb/0x15f
[ 3433.449117] [<ffffffff810b69bc>] ? kswapd+0x574/0x96a
[ 3433.449117] [<ffffffff810b6448>] ? kswapd+0x0/0x96a
[ 3433.449117] [<ffffffff810714e2>] ? kthread+0x7d/0x85
[ 3433.449117] [<ffffffff8102d6d4>] ? kernel_thread_helper+0x4/0x10
[ 3433.449117] [<ffffffff81569200>] ? restore_args+0x0/0x30
[ 3433.449117] [<ffffffff81071465>] ? kthread+0x0/0x85
[ 3433.449117] [<ffffffff8102d6d0>] ? kernel_thread_helper+0x0/0x10
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
|
|
When two process open the same file we can end up with both of them
allocating the writeback_fid. Add a new mutex which can be used
for synchronizing v9fs_inode member values.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
|
|
This change moves unaccounted_time to only be reported when
CONFIG_DEBUG_BLK_CGROUP is true.
Signed-off-by: Justin TerAvest <teravest@google.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
Commit "Add unaccounted time to timeslice_used" changed the behavior of
cfq_preempt_queue to set cfqq active. Vivek pointed out that other
preemption rules might get involved, so we shouldn't manually set which
queue is active.
This cleans up the code to just clear the queue stats at preemption
time.
Signed-off-by: Justin TerAvest <teravest@google.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
Add compatibility for composite and s-video inputs. Some TV cards hasn't
it.
Fix S-Video input, the s-video cable has only video signals no
audio. Call the function of audio configure kill chroma in signal. only
b/w video.
Known bugs:
- after s-video the audio for radio didn't work, TV crashed hardly
- after composite TV crashed hardly too.
P.S. After this patch I'll want to rework the procedure of configure
video. Now it has a lot of junk and dubles.
With my best regards, Dmitry.
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
