| Age | Commit message (Collapse) | Author |
|---|
|
dev_consume_skb_irq() should be called in moxart_tx_finished() when
skb xmit done. It makes drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
dev_consume_skb_irq() should be called in mace_interrupt() when skb
xmit done. It makes drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
dev_consume_skb_irq() should be called when skb xmit done. It makes
drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
drop profiles
dev_consume_skb_irq() should be called in emac_mac_tx_process() when
skb xmit done. It makes drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
profiles
dev_consume_skb_irq() should be called when skb xmit done. It makes
drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The GPIO interrupt controller on the espressobin board only supports edge interrupts.
If one enables the use of hardware interrupts in the device tree for the 88E6341, it is
possible to miss an edge. When this happens, the INTn pin on the Marvell switch is
stuck low and no further interrupts occur.
I found after adding debug statements to mv88e6xxx_g1_irq_thread_work() that there is
a race in handling device interrupts (e.g. PHY link interrupts). Some interrupts are
directly cleared by reading the Global 1 status register. However, the device interrupt
flag, for example, is not cleared until all the unmasked SERDES and PHY ports are serviced.
This is done by reading the relevant SERDES and PHY status register.
The code only services interrupts whose status bit is set at the time of reading its status
register. If an interrupt event occurs after its status is read and before all interrupts
are serviced, then this event will not be serviced and the INTn output pin will remain low.
This is not a problem with polling or level interrupts since the handler will be called
again to process the event. However, it's a big problem when using level interrupts.
The fix presented here is to add a loop around the code servicing switch interrupts. If
any pending interrupts remain after the current set has been handled, we loop and process
the new set. If there are no pending interrupts after servicing, we are sure that INTn has
gone high and we will get an edge when a new event occurs.
Tested on espressobin board.
Fixes: dc30c35be720 ("net: dsa: mv88e6xxx: Implement interrupt support.")
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
phylib enables interrupts before phy_start() has been called, and if
we receive an interrupt in a non-started state, the interrupt handler
returns IRQ_NONE. This causes problems with at least one Marvell chip
as reported by Andrew.
Fix this by handling interrupts the same as in phy_mac_interrupt(),
basically always running the phylib state machine. It knows when it
has to do something and when not.
This change allows to handle interrupts gracefully even if they
occur in a non-started state.
Fixes: 2b3e88ea6528 ("net: phy: improve phy state checking")
Reported-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Peter Oskolkov says:
====================
This patchset implements BPF_LWT_ENCAP_IP mode in bpf_lwt_push_encap
BPF helper. It enables BPF programs (specifically, BPF_PROG_TYPE_LWT_IN
and BPF_PROG_TYPE_LWT_XMIT prog types) to add IP encapsulation headers
to packets (e.g. IP/GRE, GUE, IPIP).
This is useful when thousands of different short-lived flows should be
encapped, each with different and dynamically determined destination.
Although lwtunnels can be used in some of these scenarios, the ability
to dynamically generate encap headers adds more flexibility, e.g.
when routing depends on the state of the host (reflected in global bpf
maps).
V2 changes: added flowi-based route lookup, IPv6 encapping, and
encapping on ingress.
V3 changes: incorporated David Ahern's suggestions:
- added l3mdev check/oif (patch 2)
- sync bpf.h from include/uapi into tools/include/uapi
- selftest tweaks
V4 changes: moved route lookup/dst change from bpf_push_ip_encap
to when BPF_LWT_REROUTE is handled, as suggested by David Ahern.
V5 changes: added a check in lwt_xmit that skb->protocol stays the
same if the skb is to be passed back to the stack (ret == BPF_OK).
Again, suggested by David Ahern.
V6 changes: abandoned.
V7 changes: added handling of GSO packets (patch 3 in the patchset added),
as suggested by BPF maintainers.
V8 changes:
- fixed build errors when LWT or IPV6 are not enabled;
- whitelisted TCP GSO instead of blacklisting SCTP and UDP GSO, as
suggested by Willem de Bruijn;
- added validation that pushed length cover needed headers when GRE/UDP
encap is detected, as suggested by Willem de Bruijn;
- a couple of minor/stylistic tweaks/fixed typos.
V9 changes:
- fixed a kbuild test robot compiler warning;
- added ipv6_route_input to ipv6_stub (patch 4 in the patchset
added), and IPv6 routing functions are now invoked via ipv6_stub,
as suggested by David Ahern.
V10 changes:
- removed unnecessary IS_ENABLED and pr_warn_once from patch 5.
V11 changes: fixed a potential dst leak in patch 5, as suggested by
David Ahern.
====================
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
This patch adds a bpf self-test to cover BPF_LWT_ENCAP_IP mode
in bpf_lwt_push_encap.
Covered:
- encapping in LWT_IN and LWT_XMIT
- IPv4 and IPv6
A follow-up patch will add GSO and VRF-enabled tests.
Signed-off-by: Peter Oskolkov <posk@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
This patch copies changes in bpf.h done by a previous patch
in this patchset from the kernel uapi include dir into tools
uapi include dir.
Signed-off-by: Peter Oskolkov <posk@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
This patch builds on top of the previous patch in the patchset,
which added BPF_LWT_ENCAP_IP mode to bpf_lwt_push_encap. As the
encapping can result in the skb needing to go via a different
interface/route/dst, bpf programs can indicate this by returning
BPF_LWT_REROUTE, which triggers a new route lookup for the skb.
v8 changes: fix kbuild errors when LWTUNNEL_BPF is builtin, but
IPV6 is a module: as LWTUNNEL_BPF can only be either Y or N,
call IPV6 routing functions only if they are built-in.
v9 changes:
- fixed a kbuild test robot compiler warning;
- call IPV6 routing functions via ipv6_stub.
v10 changes: removed unnecessary IS_ENABLED and pr_warn_once.
v11 changes: fixed a potential dst leak.
Signed-off-by: Peter Oskolkov <posk@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Proxy ip6_route_input via ipv6_stub, for later use by lwt bpf ip encap
(see the next patch in the patchset).
Signed-off-by: Peter Oskolkov <posk@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
This patch adds handling of GSO packets in bpf_lwt_push_ip_encap()
(called from bpf_lwt_push_encap):
* IPIP, GRE, and UDP encapsulation types are deduced by looking
into iphdr->protocol or ipv6hdr->next_header;
* SCTP GSO packets are not supported (as bpf_skb_proto_4_to_6
and similar do);
* UDP_L4 GSO packets are also not supported (although they are
not blocked in bpf_skb_proto_4_to_6 and similar), as
skb_decrease_gso_size() will break it;
* SKB_GSO_DODGY bit is set.
Note: it may be possible to support SCTP and UDP_L4 gso packets;
but as these cases seem to be not well handled by other
tunneling/encapping code paths, the solution should
be generic enough to apply to all tunneling/encapping code.
v8 changes:
- make sure that if GRE or UDP encap is detected, there is
enough of pushed bytes to cover both IP[v6] + GRE|UDP headers;
- do not reject double-encapped packets;
- whitelist TCP GSO packets rather than block SCTP GSO and
UDP GSO.
Signed-off-by: Peter Oskolkov <posk@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Implement BPF_LWT_ENCAP_IP mode in bpf_lwt_push_encap BPF helper.
It enables BPF programs (specifically, BPF_PROG_TYPE_LWT_IN and
BPF_PROG_TYPE_LWT_XMIT prog types) to add IP encapsulation headers
to packets (e.g. IP/GRE, GUE, IPIP).
This is useful when thousands of different short-lived flows should be
encapped, each with different and dynamically determined destination.
Although lwtunnels can be used in some of these scenarios, the ability
to dynamically generate encap headers adds more flexibility, e.g.
when routing depends on the state of the host (reflected in global bpf
maps).
v7 changes:
- added a call skb_clear_hash();
- removed calls to skb_set_transport_header();
- refuse to encap GSO-enabled packets.
v8 changes:
- fix build errors when LWT is not enabled.
Note: the next patch in the patchset with deal with GSO-enabled packets,
which are currently rejected at encapping attempt.
Signed-off-by: Peter Oskolkov <posk@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
This patch adds all needed plumbing in preparation to allowing
bpf programs to do IP encapping via bpf_lwt_push_encap. Actual
implementation is added in the next patch in the patchset.
Of note:
- bpf_lwt_push_encap can now be called from BPF_PROG_TYPE_LWT_XMIT
prog types in addition to BPF_PROG_TYPE_LWT_IN;
- if the skb being encapped has GSO set, encapsulation is limited
to IPIP/IP+GRE/IP+GUE (both IPv4 and IPv6);
- as route lookups are different for ingress vs egress, the single
external bpf_lwt_push_encap BPF helper is routed internally to
either bpf_lwt_in_push_encap or bpf_lwt_xmit_push_encap BPF_CALLs,
depending on prog type.
v8 changes: fixed a typo.
Signed-off-by: Peter Oskolkov <posk@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
In sctp_stream_init(), after sctp_stream_outq_migrate() freed the
surplus streams' ext, but sctp_stream_alloc_out() returns -ENOMEM,
stream->outcnt will not be set to 'outcnt'.
With the bigger value on stream->outcnt, when closing the assoc and
freeing its streams, the ext of those surplus streams will be freed
again since those stream exts were not set to NULL after freeing in
sctp_stream_outq_migrate(). Then the invalid-free issue reported by
syzbot would be triggered.
We fix it by simply setting them to NULL after freeing.
Fixes: 5bbbbe32a431 ("sctp: introduce stream scheduler foundations")
Reported-by: syzbot+58e480e7b28f2d890bfd@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jianlin reported a panic when running sctp gso over gre over vlan device:
[ 84.772930] RIP: 0010:do_csum+0x6d/0x170
[ 84.790605] Call Trace:
[ 84.791054] csum_partial+0xd/0x20
[ 84.791657] gre_gso_segment+0x2c3/0x390
[ 84.792364] inet_gso_segment+0x161/0x3e0
[ 84.793071] skb_mac_gso_segment+0xb8/0x120
[ 84.793846] __skb_gso_segment+0x7e/0x180
[ 84.794581] validate_xmit_skb+0x141/0x2e0
[ 84.795297] __dev_queue_xmit+0x258/0x8f0
[ 84.795949] ? eth_header+0x26/0xc0
[ 84.796581] ip_finish_output2+0x196/0x430
[ 84.797295] ? skb_gso_validate_network_len+0x11/0x80
[ 84.798183] ? ip_finish_output+0x169/0x270
[ 84.798875] ip_output+0x6c/0xe0
[ 84.799413] ? ip_append_data.part.50+0xc0/0xc0
[ 84.800145] iptunnel_xmit+0x144/0x1c0
[ 84.800814] ip_tunnel_xmit+0x62d/0x930 [ip_tunnel]
[ 84.801699] gre_tap_xmit+0xac/0xf0 [ip_gre]
[ 84.802395] dev_hard_start_xmit+0xa5/0x210
[ 84.803086] sch_direct_xmit+0x14f/0x340
[ 84.803733] __dev_queue_xmit+0x799/0x8f0
[ 84.804472] ip_finish_output2+0x2e0/0x430
[ 84.805255] ? skb_gso_validate_network_len+0x11/0x80
[ 84.806154] ip_output+0x6c/0xe0
[ 84.806721] ? ip_append_data.part.50+0xc0/0xc0
[ 84.807516] sctp_packet_transmit+0x716/0xa10 [sctp]
[ 84.808337] sctp_outq_flush+0xd7/0x880 [sctp]
It was caused by SKB_GSO_CB(skb)->csum_start not set in sctp_gso_segment.
sctp_gso_segment() calls skb_segment() with 'feature | NETIF_F_HW_CSUM',
which causes SKB_GSO_CB(skb)->csum_start not to be set in skb_segment().
For TCP/UDP, when feature supports HW_CSUM, CHECKSUM_PARTIAL will be set
and gso_reset_checksum will be called to set SKB_GSO_CB(skb)->csum_start.
So SCTP should do the same as TCP/UDP, to call gso_reset_checksum() when
computing checksum in sctp_gso_segment.
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Maxime Chevallier says:
====================
net: phy: Add 2.5G/5GBASET PHYs support
The 802.3bz standard defines 2 modes based on the NBASET alliance work
that allow to use 2.5Gbps and 5Gbps speeds on Cat 5e, 6 and 7 cables.
This series adds the necessary infrastructure to handle these modes with
C45 PHYs. This series was originally part of a bigger one, that has
seen 2 iterations [1] [2] that added support for these modes on Marvell
Alaska PHYs.
Following some discussions with Heiner and Andrew [3], we decided to
split-out the generic parts so that we can work together on the
following steps to get these mode fully working with Aquantia and
Marvell PHYS.
The first 3 patches are reworking some of the internal network phy
infrastructure to handle the new modes in a more generic way.
The 4th patch adds all the C45 register definition and accesses that
follows the 802.3bz standard to support 2.5GBASET and 5GBASET.
[1] : https://lore.kernel.org/netdev/20190118152352.26417-1-maxime.chevallier@bootlin.com/
[2] : https://lore.kernel.org/netdev/20190207094939.27369-1-maxime.chevallier@bootlin.com/
[3] : https://lore.kernel.org/netdev/81c340ea-54b0-1abf-94af-b8dc4ee83e3a@gmail.com/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 802.3bz specification, based on previous by the NBASET alliance,
defines the 2.5GBaseT and 5GBaseT link modes for ethernet traffic on
cat5e, cat6 and cat7 cables.
These mode integrate with the already defined C45 MDIO PMA/PMD registers
set that added 10G support, by defining some previously reserved bits,
and adding a new register (2.5G/5G Extended abilities).
This commit adds the required definitions in include/uapi/linux/mdio.h
to support these modes, and detect when a link-partner advertises them.
It also adds support for these mode in the generic C45 PHY
infrastructure.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Marvell 10G PHY driver has a generic way of initializing the supported
link modes by reading the PHY's C45 PMA abilities. This can be made
generic, since these registers are part of the 802.3 specifications.
This commit extracts the config_init link_mode initialization code from
marvell10g and uses it to introduce the genphy_c45_pma_read_abilities
function.
Only PMA modes are read, it's still up to the caller to set the Pause
parameters.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since of_set_phy_supported was moved to phy-core.c, we can also move
of_set_phy_eee_broken to the same location, so that we have all OF
functions in the same place.
This patch doesn't intend to introduce any change in behaviour.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When setting a PHY's max speed using either the max-speed DT property
or ethtool, we should mask-out all non-compatible modes according to the
settings table, instead of just the 10/100BASET modes.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Suggested-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pablo Neira Ayuso says:
====================
Netfilter/IPVS fixes for net
The following patchset contains Netfilter/IPVS fixes for net:
1) Missing structure initialization in ebtables causes splat with
32-bit user level on a 64-bit kernel, from Francesco Ruggeri.
2) Missing dependency on nf_defrag in IPVS IPv6 codebase, from
Andrea Claudi.
3) Fix possible use-after-free from release path of target extensions.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2019-02-13
This series introduces some fixes to mlx5 driver.
For more information please see tag log below.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently mlx5 driver creates xdp redirect hw queues unconditionally on
netdevice open, This is great until someone starts redirecting XDP traffic
via ndo_xdp_xmit on mlx5 device and changes the device configuration at
the same time, this might cause crashes, since the other device's napi
is not aware of the mlx5 state change (resources un-availability).
To fix this we must synchronize with other devices napi's on the system.
Added a new flag under mlx5e_priv to determine XDP TX resources are
available, set/clear it up when necessary and use synchronize_rcu()
when the flag is turned off, so other napi's are in-sync with it, before
we actually cleanup the hw resources.
The flag is tested prior to committing to transmit on mlx5e_xdp_xmit, and
it is sufficient to determine if it safe to transmit or not. The other
two internal flags (MLX5E_STATE_OPENED and MLX5E_SQ_STATE_ENABLED) become
unnecessary. Thus, they are removed from data path.
Fixes: 58b99ee3e3eb ("net/mlx5e: Add support for XDP_REDIRECT in device-out side")
Reported-by: Toke Høiland-Jørgensen <toke@redhat.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Eliminate the following compilation warning:
drivers/net/ethernet/mellanox/mlx5/core/events.c: warning: 'error_str'
may be used uninitialized in this function [-Wuninitialized]: => 238:3
Fixes: c2fb3db22d35 ("net/mlx5: Rework handling of port module events")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Mikhael Goikhman <migo@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
When EEH is injected and PCI bus stalls, mlx5's pci error detect
function is called to deactivate the command interface and tear down
the device. The issue is that there can be a thread that already
passed MLX5_DEVICE_STATE_INTERNAL_ERROR check, it will send the command
and stuck in the wait_func.
Solution:
Add function mlx5_cmd_flush to disable command interface and clear all
the pending commands. When device state is set to
MLX5_DEVICE_STATE_INTERNAL_ERROR, call mlx5_cmd_flush to ensure all
pending threads waiting for firmware commands completion are terminated.
Fixes: c1d4d2e92ad6 ("net/mlx5: Avoid calling sleeping function by the health poll thread")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
New channels are applied to the priv channels only after they
are successfully opened. Then, the indirection table should be built
according to the new number of channels.
Currently, such build is preformed independently of whether the
channels opening is successful, and is not reverted on failure.
The bug is caused due to removal of rss params from channels struct
and moving it to priv struct. That change cause to independency between
channels and rss params.
This causes a crash on a later point, when accessing rqn of a non
existing channel.
This patch fixes it by moving the indirection table build right before
switching the priv channels to new channels struct, after the new set of
channels was successfully opened.
Fixes: bbeb53b8b2c9 ("net/mlx5e: Move RSS params to a dedicated struct")
Signed-off-by: Maria Pasechnik <mariap@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
VFIO TCE IOMMU v2 owns IOMMU tables. When we detach an IOMMU group from
a container, we need to unset these tables from the group which we do by
calling unset_window(). We also unset tables when removing a DMA window
via the VFIO_IOMMU_SPAPR_TCE_REMOVE ioctl.
The window removal checks if the table actually exists (hidden inside
tce_iommu_find_table()) but the group detaching does not so the user
may see duplicating messages:
pci 0009:03 : [PE# fd] Removing DMA window #0
pci 0009:03 : [PE# fd] Removing DMA window #1
pci 0009:03 : [PE# fd] Removing DMA window #0
pci 0009:03 : [PE# fd] Removing DMA window #1
At the moment this is not a problem as the second invocation
of unset_window() writes zeroes to the HW registers again and exits early
as there is no table.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into kvm-master
KVM/ARM fixes for 5.0:
- Fix the way we reset vcpus, plugging the race that could happen on VHE
- Fix potentially inconsistent group setting for private interrupts
- Don't generate UNDEF when LORegion feature is present
- Relax the restriction on using stage2 PUD huge mapping
- Turn some spinlocks into raw_spinlocks to help RT compliance
|
|
A recently added preemption timer consistency check was unintentionally
dropped when the consistency checks were being reorganized to match the
SDM's ordering.
Fixes: 461b4ba4c7ad ("KVM: nVMX: Move the checks for VM-Execution Control Fields to a separate helper function")
Cc: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fix from Steven Rostedt:
"This fixes kprobes/uprobes dynamic processing of strings, where it
processes the args but does not update the remaining length of the
buffer that the string arguments will be placed in. It constantly
passes in the total size of buffer used instead of passing in the
remaining size of the buffer used.
This could cause issues if the strings are larger than the max size of
an event which could cause the strings to be written beyond what was
reserved on the buffer"
* tag 'trace-v5.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: probeevent: Correctly update remaining space in dynamic area
|
|
Update newly introduced function to be aligned to netdev coding style.
Fixes: 46861e3e88be ("net/mlx5: Set ODP SRQ support in firmware")
Reported-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
|
|
Fetch pointer to module before target object is released.
Fixes: 29e3880109e3 ("netfilter: nf_tables: fix use-after-free when deleting compat expressions")
Fixes: 0ca743a55991 ("netfilter: nf_tables: add compatibility layer for x_tables")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into clk-fixes
Pull Allwinner clock fixes from Maxime Ripard:
Two fixes for clock indices, one for the A31 and one for the V3s.
* tag 'sunxi-clk-fixes-for-5.0' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
clk: sunxi: A31: Fix wrong AHB gate number
clk: sunxi-ng: v3s: Fix TCON reset de-assert bit
|
|
Add a prefix for SPI DMA channel macros to avoid namespace conflicts,
and no functional changes.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Don't warn or fail if it's missing.
v2: handle xgmi case more gracefully.
v3: handle older kernels properly
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Tested-by: James Zhu <James.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Pull single NVMe fix from Christoph
* 'nvme-5.0' of git://git.infradead.org/nvme:
nvme-pci: add missing unlock for reset error
|
|
In the middle of do_exit() there is there is a call
"ptrace_event(PTRACE_EVENT_EXIT, code);" That call places the process
in TACKED_TRACED aka "(TASK_WAKEKILL | __TASK_TRACED)" and waits for
for the debugger to release the task or SIGKILL to be delivered.
Skipping past dequeue_signal when we know a fatal signal has already
been delivered resulted in SIGKILL remaining pending and
TIF_SIGPENDING remaining set. This in turn caused the
scheduler to not sleep in PTACE_EVENT_EXIT as it figured
a fatal signal was pending. This also caused ptrace_freeze_traced
in ptrace_check_attach to fail because it left a per thread
SIGKILL pending which is what fatal_signal_pending tests for.
This difference in signal state caused strace to report
strace: Exit of unknown pid NNNNN ignored
Therefore update the signal handling state like dequeue_signal
would when removing a per thread SIGKILL, by removing SIGKILL
from the per thread signal mask and clearing TIF_SIGPENDING.
Acked-by: Oleg Nesterov <oleg@redhat.com>
Reported-by: Oleg Nesterov <oleg@redhat.com>
Reported-by: Ivan Delalande <colona@arista.com>
Cc: stable@vger.kernel.org
Fixes: 35634ffa1751 ("signal: Always notice exiting tasks")
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
|
|
I fixed a similar build error in commit 1b1e4ee86e00 ("sh: fix build
error for empty CONFIG_BUILTIN_DTB_SOURCE"), but it came back again.
Since commit 37c8a5fafa3b ("kbuild: consolidate Devicetree dtb
build rules"), the combination of CONFIG_OF_EARLY_FLATTREE=y and
CONFIG_USE_BUILTIN_DTB=n results in the following build error:
make[1]: *** No rule to make target 'arch/sh/boot/dts/.dtb.o',
needed by 'arch/sh/boot/dts/built-in.a'. Stop.
Prior to that commit, there was only one path to descend into
arch/sh/boot/dts/, and arch/sh/Makefile correctly guards it with
CONFIG_USE_BUILTIN_DTB:
core-$(CONFIG_USE_BUILTIN_DTB) += arch/sh/boot/dts/
Now, there is another path to descend there from the top Makefile
when CONFIG_OF_EARLY_FLATTREE=y. If CONFIG_USE_BUILTIN_DTB is disabled,
CONFIG_BUILTIN_DTB_SOURCE is invisible instead of defined as "".
Add obj-$(CONFIG_USE_BUILTIN_DTB) guard to avoid the attempt to build
the non-existing file.
Fixes: 37c8a5fafa3b ("kbuild: consolidate Devicetree dtb build rules")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Cadence OSPI controller IP supports Octal IO (x8 IO lines),
It also has an integrated PHY. IP register layout is very
similar to existing QSPI IP except for additional bits to support Octal
and Octal DDR mode. Therefore, extend current driver to support Octal
mode. Only Octal SDR read (1-1-8)mode is supported for now.
Tested with mt35xu512aba Octal flash on TI's AM654 EVM.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
|
|
AM654 SoC has Cadence Octal SPI controller, which is similar to Cadence
QSPI controller but supports Octal IO(x8 data lines) and Double Data
Rate(DDR) mode. Add new compatible to support OSPI controller on TI's
AM654 SoCs.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
|
|
Due to two different versions (S25FL128SAGBHI200 and S25FL128SAGBHI210) of
the s25fl128s qspi memory, the single "s25fl128s" device entry must be
split into two to match the correct JEDEC ID's for each version. Solves
paging related issues of S25FL128SAGBHI210 chips.
Signed-off-by: Ahmet Celenk <ahmet.celenk@procenne.com>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
|
|
This change helps me to get multiple mtd device registered. Without this
I get
sysfs: cannot create duplicate filename '/bus/nvmem/devices/flash0'
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.0.0-rc2-00557-g1ef20ef21f22 #13
Call Trace:
[c0000000b38e3220] [c000000000b58fe4] dump_stack+0xe8/0x164 (unreliable)
[c0000000b38e3270] [c0000000004cf074] sysfs_warn_dup+0x84/0xb0
[c0000000b38e32f0] [c0000000004cf6c4] sysfs_do_create_link_sd.isra.0+0x114/0x150
[c0000000b38e3340] [c000000000726a84] bus_add_device+0x94/0x1e0
[c0000000b38e33c0] [c0000000007218f0] device_add+0x4d0/0x830
[c0000000b38e3480] [c0000000009d54a8] nvmem_register.part.2+0x1c8/0xb30
[c0000000b38e3560] [c000000000834530] mtd_nvmem_add+0x90/0x120
[c0000000b38e3650] [c000000000835bc8] add_mtd_device+0x198/0x4e0
[c0000000b38e36f0] [c00000000083619c] mtd_device_parse_register+0x11c/0x280
[c0000000b38e3780] [c000000000840830] powernv_flash_probe+0x180/0x250
[c0000000b38e3820] [c00000000072c120] platform_drv_probe+0x60/0xf0
[c0000000b38e38a0] [c0000000007283c8] really_probe+0x138/0x4d0
[c0000000b38e3930] [c000000000728acc] driver_probe_device+0x13c/0x1b0
[c0000000b38e39b0] [c000000000728c7c] __driver_attach+0x13c/0x1c0
[c0000000b38e3a30] [c000000000725130] bus_for_each_dev+0xa0/0x120
[c0000000b38e3a90] [c000000000727b2c] driver_attach+0x2c/0x40
[c0000000b38e3ab0] [c0000000007270f8] bus_add_driver+0x228/0x360
[c0000000b38e3b40] [c00000000072a2e0] driver_register+0x90/0x1a0
[c0000000b38e3bb0] [c00000000072c020] __platform_driver_register+0x50/0x70
[c0000000b38e3bd0] [c00000000105c984] powernv_flash_driver_init+0x24/0x38
[c0000000b38e3bf0] [c000000000010904] do_one_initcall+0x84/0x464
[c0000000b38e3cd0] [c000000001004548] kernel_init_freeable+0x530/0x634
[c0000000b38e3db0] [c000000000011154] kernel_init+0x1c/0x168
[c0000000b38e3e20] [c00000000000bed4] ret_from_kernel_thread+0x5c/0x68
mtd mtd1: Failed to register NVMEM device
With the change we now have
root@(none):/sys/bus/nvmem/devices# ls -al
total 0
drwxr-xr-x 2 root root 0 Feb 6 20:49 .
drwxr-xr-x 4 root root 0 Feb 6 20:49 ..
lrwxrwxrwx 1 root root 0 Feb 6 20:49 flash@0 -> ../../../devices/platform/ibm,opal:flash@0/mtd/mtd0/flash@0
lrwxrwxrwx 1 root root 0 Feb 6 20:49 flash@1 -> ../../../devices/platform/ibm,opal:flash@1/mtd/mtd1/flash@1
Fixes: 1cbb4a1c433a ("mtd: powernv: Add powernv flash MTD abstraction driver")
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
|
|
With this patch, we use the mtd->name instead of concatenating the name
with '0'.
Fixes: c4dfa25ab307 ("mtd: add support for reading MTD devices via the nvmem API")
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
|
|
The step values for some of the LDOs appears to be incorrect, resulting
in incorrect voltages (or at least, ones which are different from the
Samsung 3.4 vendor kernel).
Signed-off-by: Stuart Menefy <stuart.menefy@mathembedded.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
|
|
Add DMA mode support for the Spreadtrum SPI controller, and we will enable
SPI interrupt to help to complete the SPI transfer work in DMA mode.
Signed-off-by: Lanqing Liu <lanqing.liu@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add the DMA properties for the SPI dma mode.
Signed-off-by: Lanqing Liu <lanqing.liu@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The SPI irq event will use to complete the SPI work in the SPI DMA mode,
so this patch is a preparation for the following DMA mode support.
Moreover the SPI interrupt can be fired when removing the SPI controller,
so we should make sure the SPI controller has stopped the queue in
remove function before freeing the SPI irq.
Signed-off-by: Lanqing Liu <lanqing.liu@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
dump_thread32() in aout_core_dump() does not clear the user32 structure
allocated on the stack as the first thing on function entry.
As a result, the dump.u_comm, dump.u_ar0 and dump.signal which get
assigned before the clearing, get overwritten.
Rename that function to fill_dump() to make it clear what it does and
call it first thing.
This was caught while staring at a patch by Derek Robson
<robsonde@gmail.com>.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Derek Robson <robsonde@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michael Matz <matz@suse.de>
Cc: x86@kernel.org
Cc: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/20190202005512.3144-1-robsonde@gmail.com
|
