summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2014-11-26ath10k: don't drop corrupted mgmt framesMichal Kazior
Some firmware revisions don't seem to deilver management frames with FCS error via WMI so narrow down the HTT rule to not drop corrupted management frames. This basically increases number of frames ath10k reports while sniffing. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-11-26ath10k: fix offchannel cancel failuresMichal Kazior
When mac80211 requests driver to cancel a hw roc the driver must not call the expired() callback or else roc will fail in some cases depending on how things get scheduled. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-11-26ath10k: make hw roc more reliableMichal Kazior
With P2P concurrency requested hw roc duration time can be very small. Some firmware revisions refuse scan requests with too small channel dwell time. This prevents messages like, e.g. with connected STA vif and performing P2P Find: ath10k_pci 0000:00:05.0: failed to switch to channel for roc scan ieee80211 phy3: failed to start next HW ROC (-110) Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-11-26ath10k: fix offchan reliabilityMichal Kazior
New firmware revisions don't need peer creation when doing offchannel tx. Earlier revisions would queue and never release frames without a peer. This prevent new firmware revisions from stopping replenishing wmi-htc tx credits and improves reliability of offchannel tx which would sometimes silently fail. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-11-26irqchip: brcmstb-l2: Fix error handling of irq_of_parse_and_mapDmitry Torokhov
Return value of irq_of_parse_and_map() is unsigned int, with 0 indicating failure, so testing for negative result never works. Signed-off-by: Dmitry Torokhov <dtor@chromium.org> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Tested-by: Kevin Cernekee <cernekee@gmail.com> Link: https://lkml.kernel.org/r/20141114221642.GA37468@dtor-ws Signed-off-by: Jason Cooper <jason@lakedaemon.net>
2014-11-26ath10k: remove extra_tx_headroomMichal Kazior
Comment was out-of-date. The headroom is no longer necessary because HTT Tx fragment list is stored in dma pool item associated with each sk_buff. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-11-26irqchip: bcm7120-l2: Fix error handling of irq_of_parse_and_mapDmitry Torokhov
Return value of irq_of_parse_and_map() is unsigned int, with 0 indicating failure, so testing for negative result never works. Signed-off-by: Dmitry Torokhov <dtor@chromium.org> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Tested-by: Kevin Cernekee <cernekee@gmail.com> Link: https://lkml.kernel.org/r/20141114221614.GA37395@dtor-ws Signed-off-by: Jason Cooper <jason@lakedaemon.net>
2014-11-26ath10k: use configured nss instead of max nssBen Greear
When re-associating a station, the nss was set back to maximum value even if user had configured small number of tx chains. So, pay attention to user's config in this case as well. Signed-off-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-11-26ath10k: apply chainmask settings to vdev on creationBen Greear
It appears it takes more than just setting the hardware's chainmask to make things work well. Without this patch, a vdev would only use 1x1 rates when chainmask was set to 0x3. Setting the 'nss' (number of spatial streams) on the vdev helps the firmware's rate-control algorithm work properly. Signed-off-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-11-26mac802154: remove unnecessary if statementVarka Bhadram
Removes unnecessary if statement check for net device. Error check performed after alloc_netdev(). ndev = alloc_netdev(sizeof(*sdata) + local->hw.vif_data_size, name, NET_NAME_UNKNOWN, ieee802154_if_setup); if (!ndev) return ERR_PTR(-ENOMEM); .. Signed-off-by: Varka Bhadram <varkab@cdac.in> Acked-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2014-11-26ieee802154: fix spelling mistakesVarka Bhadram
Signed-off-by: Varka Bhadram <varkab@cdac.in> Acked-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2014-11-25Merge branch 'for-3.18' of git://linux-nfs.org/~bfields/linuxLinus Torvalds
Pull nfsd bugfixes from Bruce Fields: "These fix one mishandling of the case when security labels are configured out, and two races in the 4.1 backchannel code" * 'for-3.18' of git://linux-nfs.org/~bfields/linux: nfsd: Fix slot wake up race in the nfsv4.1 callback code SUNRPC: Fix locking around callback channel reply receive nfsd: correctly define v4.2 support attributes
2014-11-25Merge git://git.kvack.org/~bcrl/aio-fixesLinus Torvalds
Pull aio fix from Ben LaHaise: "Dirty page accounting fix for aio" * git://git.kvack.org/~bcrl/aio-fixes: aio: fix uncorrent dirty pages accouting when truncating AIO ring buffer
2014-11-25Merge branch 'merge' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc Pull powerpc fixes from Ben Herrenschmidt: "This series fix a nasty issue with radeon adapters on powerpc servers, it's all CC'ed stable and has the relevant maintainers ack's/reviews. Basically, some (radeon) adapters have issues with MSI addresses above 1T (only support 40-bits). We had powerpc specific quirk but it only listed a specific revision of an adapter that we shipped with our machines and didn't properly handle the audio function which some distros enable nowadays. So we made the quirk generic and fixed both the graphic and audio drivers properly to use it. Without that, ppc64 server machines will crash at boot with a radeon adapter. Note: This has been brewing for a while, it just needed a last respin which got delayed due to us moving ozlabs to a new location in town and other such things taking priority" * 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: powerpc/pci: Remove unused force_32bit_msi quirk powerpc/pseries: Honor the generic "no_64bit_msi" flag powerpc/powernv: Honor the generic "no_64bit_msi" flag sound/radeon: Move 64-bit MSI quirk from arch to driver gpu/radeon: Set flag to indicate broken 64-bit MSI PCI/MSI: Add device flag indicating that 64-bit MSIs don't work ALSA: hda - Limit 40bit DMA for AMD HDMI controllers
2014-11-25Merge tag 'hwmon-for-linus-v3.18-rc7' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging Pull a hwmon fix from Guenter Roeck: "Fix hwmon registration problem in g762 driver" * tag 'hwmon-for-linus-v3.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: hwmon: (g762) fix call to devm_hwmon_device_register_with_groups()
2014-11-25Merge tag 'clk-fixes-for-linus' of ↵Linus Torvalds
https://git.linaro.org/people/mike.turquette/linux Pull clock fixes from Mike Turquette: "The fixes for the clock framework are all regressions in drivers, plus a single fix in one of the basic clock templates. No fixes to the core this time around. As with most clock driver fixes these run the gamut from fixing a build warning to fixing wrecked memory timings, with a little USB tossed in for fun" * tag 'clk-fixes-for-linus' of https://git.linaro.org/people/mike.turquette/linux: clk: pxa: fix pxa27x CCCR bit usage clk-divider: Fix READ_ONLY when divider > 1 clk: qcom: Fix duplicate rbcpr clock name clk: at91: usb: fix at91sam9x5 recalc, round and set rate clk: at91: usb: fix at91rm9200 round and set rate
2014-11-25Merge branch 'for-davem' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs More work from Al Viro to move away from modifying iovecs by using iov_iter instead. Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-25net: Hyper-V: Deletion of an unnecessary check before the function call "vfree"Markus Elfring
The vfree() function performs also input parameter validation. Thus the test around the call is not needed. This issue was detected by using the Coccinelle software. Signed-off-by: Markus Elfring <elfring@users.sourceforge.net> Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-25Revert "serial: of-serial: add PM suspend/resume support"Greg Kroah-Hartman
This reverts commit 2dea53bf57783f243c892e99c10c6921e956aa7e. Turns out to be broken :( Cc: Jingchang Lu <jingchang.lu@freescale.com> Cc: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-11-25tg3: fix ring init when there are more TX than RX channelsThadeu Lima de Souza Cascardo
If TX channels are set to 4 and RX channels are set to less than 4, using ethtool -L, the driver will try to initialize more RX channels than it has allocated, causing an oops. This fix only initializes the RX ring if it has been allocated. Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-25tcp: fix possible NULL dereference in tcp_vX_send_reset()Eric Dumazet
After commit ca777eff51f7 ("tcp: remove dst refcount false sharing for prequeue mode") we have to relax check against skb dst in tcp_v[46]_send_reset() if prequeue dropped the dst. If a socket is provided, a full lookup was done to find this socket, so the dst test can be skipped. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=88191 Reported-by: Jaša Bartelj <jasa.bartelj@gmail.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Daniel Borkmann <dborkman@redhat.com> Fixes: ca777eff51f7 ("tcp: remove dst refcount false sharing for prequeue mode") Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-25rtlwifi: Change order in device startupLarry Finger
The existing order of steps when starting the PCI devices works for 2.4G devices, but fails to initialize the 5G section of the RTL8821AE hardware. This patch is needed to fix the regression reported in Bug #88811 (https://bugzilla.kernel.org/show_bug.cgi?id=88811). Reported-by: Valerio Passini <valerio.passini@unicam.it> Tested-by: Valerio Passini <valerio.passini@unicam.it> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Valerio Passini <valerio.passini@unicam.it> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-11-25rtlwifi: rtl8821ae: Fix 5G detection problemLarry Finger
The changes associated with moving this driver from staging to the regular tree missed one section setting the allowable rates for the 5GHz band. This patch is needed to fix the regression reported in Bug #88811 (https://bugzilla.kernel.org/show_bug.cgi?id=88811). Reported-by: Valerio Passini <valerio.passini@unicam.it> Tested-by: Valerio Passini <valerio.passini@unicam.it> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Valerio Passini <valerio.passini@unicam.it> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-11-25Revert "netfilter: conntrack: fix race in __nf_conntrack_confirm against ↵Pablo Neira
get_next_corpse" This reverts commit 5195c14c8b27cc0b18220ddbf0e5ad3328a04187. If the conntrack clashes with an existing one, it is left out of the unconfirmed list, thus, crashing when dropping the packet and releasing the conntrack since golden rule is that conntracks are always placed in any of the existing lists for traceability reasons. Reported-by: Daniel Borkmann <dborkman@redhat.com> Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=88841 Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-25Merge branch 'ipv6_vxlan_outer_udp_csum'David S. Miller
Alexander Duyck says: ==================== Fix outer UDP checksums for IPv6 VXLAN tunnels In testing against an older kernel I found a couple issues in the IPv6 VXLAN tunnel checksum logic for the outer UDP checksum. First the default transitioned from using an outer checksum to not using one. Second, sometime after that the checksum inputs were changed resulting the checksum not being correct if it were computed. These two issues prevented a ping from the newer kernel to the older one. With these two changes applied I verified I was able to send traffic over the VXLAN tunnel to a link partner on an older kernel. The boolean flip fix can be submitted for 3.17 stable as well since the patch that introduced the issue was included in that kernel. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-25vxlan: Fix boolean flip in VXLAN_F_UDP_ZERO_CSUM6_[TX|RX]Alexander Duyck
In "vxlan: Call udp_sock_create" there was a logic error that resulted in the default for IPv6 VXLAN tunnels going from using checksums to not using checksums. Since there is currently no support in iproute2 for setting these values it means that a kernel after the change cannot talk over a IPv6 VXLAN tunnel to a kernel prior the change. Fixes: 3ee64f3 ("vxlan: Call udp_sock_create") Cc: Tom Herbert <therbert@google.com> Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com> Acked-by: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-25ip6_udp_tunnel: Fix checksum calculationAlexander Duyck
The UDP checksum calculation for VXLAN tunnels is currently using the socket addresses instead of the actual packet source and destination addresses. As a result the checksum calculated is incorrect in some cases. Also uh->check was being set twice, first it was set to 0, and then it is set again in udp6_set_csum. This change removes the redundant assignment to 0. Fixes: acbf74a7 ("vxlan: Refactor vxlan driver to make use of the common UDP tunnel functions.") Cc: Andy Zhou <azhou@nicira.com> Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-25mwifiex: add Tx status support for ACTION framesAmitkumar Karwar
ACK status (0/1) for ACTION frames is informed to cfg80211. We will extend existing logic used for EAPOL frames. The cfg80211 API is different here. Also, we need to explicitly free cloned skb. Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-11-25mwifiex: add Tx status support for EAPOL packetsAmitkumar Karwar
Firmware notifies the driver through event if EAPOL data packet has been acked or not. We will inform this status to userspace listening on a socket. Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-11-25mwifiex: skip delay main work logic for USB interface.Amitkumar Karwar
We had introduced delay main work logic to avoid processing interrupts when Rx pending packet count reaches high threshold. interrupt processing is restarted later when packet count reduces lower threashold. This helped to reduce unnecessary overhead and improve throughput for SD and PCIe chipsets. As there are no interrupts for USB, we will skip this logic for USB chipsets. Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-11-25mwifiex: fix scan problem on big endian platformsAmitkumar Karwar
This patch adds missing endian conversion for beacon size while processing scan response. Reported-by: Daniel Mosquera <daniel.mosquera@ctag.com> Tested-by: Daniel Mosquera <daniel.mosquera@ctag.com> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-11-25mwifiex: fix sparse warningAmitkumar Karwar
This patch fixes following sparse warnings: drivers/net/wireless/mwifiex/util.c:152:19: warning: cast from restricted __le16 drivers/net/wireless/mwifiex/util.c:152:19: warning: restricted __le16 degrades to integer Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-11-25ath9k: add TPC capability to TX descriptor pathLorenzo Bianconi
Add TPC capability to TX descriptor path. Cap per-packet TX power according to TX power per-rate tables. Currently TPC is supported just by AR9003 based chips Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-11-25ath9k: add TX power per-rate tablesLorenzo Bianconi
Add TX power per-rate tables for different MIMO modes (e.g STBC) in order to cap the maximum TX power value per-rate in the TX descriptor path. Cap TX power for self generated frames (ACK, RTS/CTS). Currently TPC is supported just by AR9003 based chips Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-11-25brcmfmac: correct .disconnect() callback while connectingArend van Spriel
When the driver has sent a join iovar to the firmware it waits for the events to report result of the connection. However, the wpa_supplicant will request a .disconnect() after a timeout. So upon calling .disconnect() the interface state may still be CONNECTING. Clear the CONNECTING bit as well. Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-11-25cxgb4/cxgb4vf/csiostor: Add T4/T5 PCI ID TableHariprasad Shenai
Add a new file t4_pci_id_tbl.h that contains T4/T5 PCI ID Table so that for all drivers that uses T4/T5 PCI functions changes can be done in one place. checkpatch.pl script reports following error, which if tried to fix ends up in compilation error. ERROR: Macros with complex values should be enclosed in parentheses +#define CH_PCI_DEVICE_ID_TABLE_DEFINE_END \ + { 0, } \ + } WARNING: added, moved or deleted file(s), does MAINTAINERS need updating? new file mode 100644 ERROR: Macros with complex values should be enclosed in parentheses +#define CH_PCI_ID_TABLE_FENTRY(devid) \ + CH_PCI_ID_TABLE_ENTRY((devid) | \ + ((CH_PCI_DEVICE_ID_FUNCTION) << 8)), \ + CH_PCI_ID_TABLE_ENTRY((devid) | \ + ((CH_PCI_DEVICE_ID_FUNCTION2) << 8)) ERROR: Macros with complex values should be enclosed in parentheses +#define CH_PCI_DEVICE_ID_TABLE_DEFINE_END { 0, } } ERROR: Macros with complex values should be enclosed in parentheses +#define CH_PCI_DEVICE_ID_TABLE_DEFINE_END { 0, } } Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-25net-timestamp: Fix a documentation typoAndrew Lutomirski
SOF_TIMESTAMPING_OPT_ID puts the id in ee_data, not ee_info. Cc: Willem de Bruijn <willemb@google.com> Signed-off-by: Andy Lutomirski <luto@amacapital.net> Acked-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-25mac80211: check if channels allow 80 MHz for VHT probe requestsJohannes Berg
If there are no channels allowing 80 MHz to be used, then the station isn't really VHT capable even if the driver and device support it in general. In this case, exclude the VHT capability IE from probe request frames. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-11-25cfg80211: remove pointless channel lookup in survey codeJohannes Berg
We have a channel pointer, and we use its center frequency to look up a channel pointer - which will thus be exactly the same as the original pointer. Remove that pointless lookup and just use the pointer. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-11-25Input: xpad - use proper endpoint typeGreg Kroah-Hartman
The xpad wireless endpoint is not a bulk endpoint on my devices, but rather an interrupt one, so the USB core complains when it is submitted. I'm guessing that the author really did mean that this should be an interrupt urb, but as there are a zillion different xpad devices out there, let's cover out bases and handle both bulk and interrupt endpoints just as easily. Signed-off-by: "Pierre-Loup A. Griffais" <pgriffais@valvesoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: stable <stable@vger.kernel.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2014-11-25Input: elantech - trust firmware about trackpoint presenceDmitry Torokhov
Only try to parse data as coming from trackpoint if firmware told us that trackpoint is present. Fixes commit caeb0d37fa3e387eb0dd22e5d497523c002033d1 Reported-and-tested-by: Marcus Overhagen <marcus.overhagen@gmail.com> Reported-and-tested-by: Anders Kaseorg <andersk@mit.edu> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2014-11-25Merge remote-tracking branch 'iwlwifi-fixes/master' into iwlwifi-nextEmmanuel Grumbach
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Conflicts: drivers/net/wireless/iwlwifi/iwl-fw.h
2014-11-24usb-quirks: Add reset-resume quirk for MS Wireless Laser Mouse 6000Hans de Goede
This wireless mouse receiver needs a reset-resume quirk to properly come out of reset. BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1165206 Signed-off-by: Hans de Goede <hdegoede@redhat.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-11-24net: wireless: rtlwifi: rtl8192ee: Fix compilation of the driverAndreas Ruprecht
In the Makefile for this driver, the wrong Kconfig option is used to trigger the compilation of the object file. This leads to the driver only being included into the kernel when both CONFIG_RTL8821AE and CONFIG_RTL8192AE are set to "y". Signed-off-by: Andreas Ruprecht <rupran@einserver.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-11-24net: wireless: rtlwifi: Do not always include drivers in obj-mAndreas Ruprecht
In four of the rtlwifi drivers, the Makefile contains superfluous statements indicating the compilation of the driver as an LKM regardless of the corresponding Kconfig option. If the corresponding option is set to 'y', the build system will then see the object file in obj-m and obj-y, which leads to a compilation as a built-in only. Even though this leads to the desired behavior, the unconditional appearance in obj-m is confusing for someone reading the Makefile. This patch removes the superfluous Makefile statements. Signed-off-by: Andreas Ruprecht <rupran@einserver.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-11-24ath: Fix a false radar detection patternVivek Natarajan
For FCC and JP, in one of the radar patterns, PPB and PRF seems to be interchanged leading to frequent incorrect radar detections. Signed-off-by: Vivek Natarajan <nataraja@qti.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-11-24wireless/p54: Remove duplicated net2280 headerRicardo Ribalda Delgado
The usb gadget driver net2280 has exported a header file with the register definition of the net2280 chip. Remove the custom/duplicated header file in favor of that header file in include/linux Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-11-24rtlwifi: update RCR register in rtl_op_configure_filter()Lorenzo Bianconi
Reconfigure RCR register in rtl_op_configure_filter() in order to apply RX filter configuration Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-11-24net/ping: handle protocol mismatching scenarioJane Zhou
ping_lookup() may return a wrong sock if sk_buff's and sock's protocols dont' match. For example, sk_buff's protocol is ETH_P_IPV6, but sock's sk_family is AF_INET, in that case, if sk->sk_bound_dev_if is zero, a wrong sock will be returned. the fix is to "continue" the searching, if no matching, return NULL. Cc: "David S. Miller" <davem@davemloft.net> Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru> Cc: James Morris <jmorris@namei.org> Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org> Cc: Patrick McHardy <kaber@trash.net> Cc: netdev@vger.kernel.org Cc: stable@vger.kernel.org Signed-off-by: Jane Zhou <a17711@motorola.com> Signed-off-by: Yiwei Zhao <gbjc64@motorola.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24net/smsc911x: Add minimal runtime PM supportGeert Uytterhoeven
Add minimal runtime PM support (enable on probe, disable on remove), to ensure proper operation with a parent device that uses runtime PM. This is needed on systems where the external bus controller module of the SoC is contained in a PM domain and/or has a gateable functional clock. In such cases, before accessing any device connected to the external bus, the PM domain must be powered up, and/or the functional clock must be enabled, which is typically handled through runtime PM by the bus controller driver. An example of this is the kzm9g development board, where an smsc9220 Ethernet controller is connected to the Bus State Controller (BSC) of a Renesas sh73a0 SoC. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit (git 2.34.1) at 2025-09-16 01:45:29 +0000