| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
When a targetport is removed from the config, fcloop will avoid calling
the LS done() routine thinking the targetport is gone. This leaves the
initiator reset/reconnect hanging as it waits for a status on the
Create_Association LS for the reconnect.
Change the filter in the LS callback path. If tport null (set when
failed validation before "sending to remote port"), be sure to call
done. This was the main bug. But, continue the logic that only calls
done if tport was set but there is no remoteport (e.g. case where
remoteport has been removed, thus host doesn't expect a completion).
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
In many architectures loads may be reordered with older stores to
different locations. In the nvme driver the following two operations
could be reordered:
- Write shadow doorbell (dbbuf_db) into memory.
- Read EventIdx (dbbuf_ei) from memory.
This can result in a potential race condition between driver and VM host
processing requests (if given virtual NVMe controller has a support for
shadow doorbell). If that occurs, then the NVMe controller may decide to
wait for MMIO doorbell from guest operating system, and guest driver may
decide not to issue MMIO doorbell on any of subsequent commands.
This issue is purely timing-dependent one, so there is no easy way to
reproduce it. Currently the easiest known approach is to run "Oracle IO
Numbers" (orion) that is shipped with Oracle DB:
orion -run advanced -num_large 0 -size_small 8 -type rand -simulate \
concat -write 40 -duration 120 -matrix row -testname nvme_test
Where nvme_test is a .lun file that contains a list of NVMe block
devices to run test against. Limiting number of vCPUs assigned to given
VM instance seems to increase chances for this bug to occur. On test
environment with VM that got 4 NVMe drives and 1 vCPU assigned the
virtual NVMe controller hang could be observed within 10-20 minutes.
That correspond to about 400-500k IO operations processed (or about
100GB of IO read/writes).
Orion tool was used as a validation and set to run in a loop for 36
hours (equivalent of pushing 550M IO operations). No issues were
observed. That suggest that the patch fixes the issue.
Fixes: f9f38e33389c ("nvme: improve performance for virtual NVMe devices")
Signed-off-by: Michal Wnukowski <wnukowski@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
[hch: updated changelog and comment a bit]
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Building the newly introduced BPF_PROG_TYPE_SK_REUSEPORT leads to
a compile time error when building with clang:
net/core/filter.o: In function `sk_reuseport_convert_ctx_access':
../net/core/filter.c:7284: undefined reference to `__compiletime_assert_7284'
It seems that clang has issues resolving hweight_long at compile
time. Since SK_FL_PROTO_MASK is a constant, we can use the interface
for known constant arguments which works fine with clang.
Fixes: 2dbb9b9e6df6 ("bpf: Introduce BPF_PROG_TYPE_SK_REUSEPORT")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
In bpf_tcp_recvmsg() we first took a reference on the psock, however
once we find that there are skbs in the normal socket's receive queue
we return with processing them through tcp_recvmsg(). Problem is that
we leak the taken reference on the psock in that path. Given we don't
really do anything with the psock at this point, move the skb_queue_empty()
test before we fetch the psock to fix this case.
Fixes: 8934ce2fd081 ("bpf: sockmap redirect ingress support")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
bpf_tcp_close() we pop the psock linkage to a map via psock_map_pop().
A parallel update on the sock hash map can happen between psock_map_pop()
and lookup_elem_raw() where we override the element under link->hash /
link->key. In bpf_tcp_close()'s lookup_elem_raw() we subsequently only
test whether an element is present, but we do not test whether the
element is infact the element we were looking for.
We lock the sock in bpf_tcp_close() during that time, so do we hold
the lock in sock_hash_update_elem(). However, the latter locks the
sock which is newly updated, not the one we're purging from the hash
table. This means that while one CPU is doing the lookup from bpf_tcp_close(),
another CPU is doing the map update in parallel, dropped our sock from
the hlist and released the psock.
Subsequently the first CPU will find the new sock and attempts to drop
and release the old sock yet another time. Fix is that we need to check
the elements for a match after lookup, similar as we do in the sock map.
Note that the hash tab elems are freed via RCU, so access to their
link->hash / link->key is fine since we're under RCU read side there.
Fixes: e9db4ef6bf4c ("bpf: sockhash fix omitted bucket lock in sock_close")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Currently, variable ref_count within the bsg_device struct is of
type atomic_t. For variables being used as reference counters,
the refcount API should be used instead of atomic. The newer
refcount API works to prevent counter overflows and use-after-free
bugs. So, move this varable from the atomic API to refcount,
potentially avoiding the issues mentioned.
Signed-off-by: John Pittman <jpittman@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
kmem_cache_destroy() can handle NULL pointer correctly, so there is
no need to check e->icq_cache before calling kmem_cache_destroy().
Signed-off-by: Chengguang Xu <cgxu519@gmx.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
In IPv4, the newly introduced rdma_read_gids is used to read the SGID/DGID
for the connection which returns GID correctly for RoCE transport as well.
In IPv6, rdma_read_gids is also used. The following are why rdma_read_gids
is introduced.
rdma_addr_get_dgid() for RoCE for client side connections returns MAC
address, instead of DGID.
rdma_addr_get_sgid() for RoCE doesn't return correct SGID for IPv6 and
when more than one IP address is assigned to the netdevice.
So the transport agnostic rdma_read_gids() API is provided by rdma_cm
module.
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 52638f71fcff ("dsa: Move gpio reset into switch driver")
moved the GPIO handling into the switch drivers but forgot
to remove the GPIO header includes.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In function tipc_dest_push, the 32bit variables 'node' and 'port'
are stored separately in uppper and lower part of 64bit 'value'.
Then this value is assigned to dst->value which is a union like:
union
{
struct {
u32 port;
u32 node;
};
u64 value;
}
This works on little-endian machines like x86 but fails on big-endian
machines.
The fix remove the 'value' stack parameter and even the 'value'
member of the union in tipc_dest, assign the 'node' and 'port' member
directly with the input parameter to avoid the endian issue.
Fixes: a80ae5306a73 ("tipc: improve destination linked list")
Signed-off-by: Zhenbo Gao <zhenbo.gao@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Haiqing Bai <Haiqing.Bai@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jiri Pirko says:
====================
net: sched: couple of small fixes
Jiri Pirko (2):
net: sched: fix extack error message when chain is failed to be
created
net: sched: return -ENOENT when trying to remove filter from
non-existent chain
====================
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When chain 0 was implicitly created, removal of non-existent filter from
chain 0 gave -ENOENT. Once chain 0 became non-implicit, the same call is
giving -EINVAL. Fix this by returning -ENOENT in that case.
Reported-by: Roman Mashak <mrv@mojatatu.com>
Fixes: f71e0ca4db18 ("net: sched: Avoid implicit chain 0 creation")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead "Cannot find" say "Cannot create".
Fixes: c35a4acc2985 ("net: sched: cls_api: handle generic cls errors")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After erspan_ver is introudced, if erspan_ver is not set in iproute, its
value will be left 0 by default. Since Commit 02f99df1875c ("erspan: fix
invalid erspan version."), it has broken the traffic due to the version
check in erspan_xmit if users are not aware of 'erspan_ver' param, like
using an old version of iproute.
To fix this compatibility problem, it sets erspan_ver to 1 by default
when adding an erspan dev in erspan_setup. Note that we can't do it in
ipgre_netlink_parms, as this function is also used by ipgre_changelink.
Fixes: 02f99df1875c ("erspan: fix invalid erspan version.")
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After changing rhashtable_walk_start to return void, start_fail would
never be set other value than 0, and the checking for start_fail is
pointless, so remove it.
Fixes: 97a6ec4ac021 ("rhashtable: Change rhashtable_walk_start to return void")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As Marcelo noticed, in sctp_transport_get_next, it is iterating over
transports but then also accessing the association directly, without
checking any refcnts before that, which can cause an use-after-free
Read.
So fix it by holding transport before accessing the association. With
that, sctp_transport_hold calls can be removed in the later places.
Fixes: 626d16f50f39 ("sctp: export some apis or variables for sctp_diag and reuse some for proc")
Reported-by: syzbot+fe62a0c9aa6a85c6de16@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The DMA is broken on this specific device for some unknown
reason (probably badly designed or plain broken interface
electronics) and will only work with PIO. Other users of
the same hardware does not have this problem.
Add a specific quirk so that this Gemini device gets
DMA turned off. Also fix up some code around passing the
port information around in probe while we're at it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The fault reports the page number where the fault happend and not
the exact faulty address. Update the print message to reflect that.
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Marek Olšák <marek.olsak@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
The dce_i2c_hw code contained four funtcions that were only
called in one place and did not have a clearly delineated
purpose.
[How]
Inline these functions, keeping the same functionality.
This is not a functional change.
The functions disable_i2c_hw_engine and release_engine_dce_hw were
pulled into their respective callers.
The most interesting part of this change is the acquire functions.
dce_i2c_hw_engine_acquire_engine was pulled into
dce_i2c_engine_acquire_hw, and dce_i2c_engine_acquire_hw was pulled
into acquire_i2c_hw_engine.
Some notes to show that this change is not functional:
-Failure conditions in any function resulted in a cascade of calls that
ended in a 'return NULL'.
Those are replaced with a direct 'return NULL'.
-The variable result is the one from dce_i2c_hw_engine_acquire_engine.
The boolean result used as part of return logic was removed.
-As the second half of dce_i2c_hw_engine_acquire_engine is only executed
if that function is returning true and therefore exiting the do-while
loop in dce_i2c_engine_acquire_hw, those lines were moved outside
of the loop.
Signed-off-by: David Francis <David.Francis@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
On PCO and up, whenever SMU receive message to indicate active
display count = 0. SMU will turn off 48MHZ TMDP reference clock
by writing to 1 TMDP_48M_Refclk_Driver_PWDN. Once this clock is
off, no PHY register will respond to register access. This means
our current sequence of notifying display count along with requesting
clock will cause driver to hang when accessing PHY registers after
displays count goes to 0.
[How]
Separate the PPSMC_MSG_SetDisplayCount message from the SMU messages
that request clocks, have display own sequencing of this message so
that we can send it at the appropriate time.
Do not redundantly power off HW when entering S3, S4, since display
should already be called to disable all streams. And ASIC soon be
powered down.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
The i2c code contains two structs that contain the same
information as i2c_payload
[How]
Replace references to those structs with references to
i2c_payload
dce_i2c_transaction_request->status was written to but never read,
so all references to it are removed
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Jordan Lazare <Jordan.Lazare@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Logging hardware state can be done by triggering a write to the
debugfs file. It would also be useful to be able to read the hardware
state from the debugfs file to be able to generate a clean log without
timestamps.
[How]
Usage: cat /sys/kernel/debug/dri/0/amdgpu_dm_dtn_log
Threading is an obvious concern when dealing with multiple debugfs
operations and blocking on global state in dm or dc seems unfavorable.
Adding an extra parameter for the debugfs log context state is the
implementation done here. Existing code that made use of DTN_INFO
and its associated macros needed to be refactored to support this.
We don't know the size of the log in advance so it reallocates the
log string dynamically. Once the log has been generated it's copied
into the user supplied buffer for the debugfs. This allows for seeking
support but it's worth nothing that unlike triggering output via
dmesg the hardware state might change in-between reads if your buffer
size is too small.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Jordan Lazare <Jordan.Lazare@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
comments
[Why]
Good spelling and grammar makes comments
more pleasant and clearer.
Linux has coding standards for comments
that we should try to follow.
[How]
Fix obvious spelling and grammar issues
Ensure all comments use '/*' and '*/' and multi-line comments
follow linux convention
Remove line-of-stars comments that do not separate sections
of code and comments referring to lines of code that have
since been removed
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
There is currently an intermittent hang from a memory leak in
DTN stress testing. It is caused by unfreed memory during driver
disable.
[How]
Do a dc_sink_release in the case that skips it incorrectly.
Signed-off-by: SivapiriyanKumarasamy <sivapiriyan.kumarasamy@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Now that we "scale" time delays correctly on Maximus (as of diags svn
r170115), the forced "35 ms" wait time now becomes 35 ms * 500 = 17.5
seconds, which is far too long. Even having to repeat polling a
register once causes excessive delays on Maximus.
[How]
Just use the regular wait time passed to the generic_reg_wait()
function. This is sufficient for Maximus now, and it also means that
there's one less "Maximus-only" code path in DAL.
Also disable the "REG_WAIT taking a while:" message on Maximus, since
things do take a while longer there and 1-2ms delays are not uncommon
(and nothing to worry about).
Signed-off-by: Ken Chalmers <ken.chalmers@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
We have logging methods for printing hardware state for newer ASICs
but no way to trigger the log output.
[How]
Add support for triggering the output via writing to a debugfs file
entry. Log output currently goes into dmesg for convenience, but
accessing via a read should be possible later.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Jordan Lazare <Jordan.Lazare@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
drm_handle_vblank is deprecated. Use drm_crtc_handle_vblank instead.
Signed-off-by: Leo (Sunpeng) Li <sunpeng.li@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Signed-off-by: Tony Cheng <tony.cheng@amd.com>
Reviewed-by: Steven Chiu <Steven.Chiu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
The function pointers of the dce_i2c_hw struct were never
accessed from outside dce_i2c_hw.c and had only one version.
As function pointers take up space and make debugging difficult,
and they are not needed in this case, they should be removed.
[How]
Remove the dce_i2c_hw_funcs struct and make static all
functions that were previously a part of it. Reorder
the functions in dce_i2c_hw.c.
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Should work on Vega10 as well, but with an obvious performance hit.
Older APUs can be enabled as well, but will probably be more work.
v2: fix error checking
v3: use more general check
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Helper to get the PDE for a PD/PT.
v2: improve documentation
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add the necessary handling.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add a helper function to figure them out only once.
v2: fix typo with memset
v3: rebase on kfd changes (Alex)
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Just another leftover from radeon.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com>
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
We can't hold the mn_lock while allocating memory.
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Chunming Zhou <david1.zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
No more waiting for a fence done here.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
1. initialize kiq before initialize gfx ring.
2. set kiq ring ready immediately when kiq initialize
successfully.
3. split function gfx_v9_0_kiq_resume into two functions.
gfx_v9_0_kiq_resume is for kiq initialize.
gfx_v9_0_kcq_resume is for kcq initialize.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
1. initialize kiq before initialize gfx ring.
2. set kiq ring ready immediately when kiq initialize
successfully.
3. split function gfx_v8_0_kiq_resume into two functions.
gfx_v8_0_kiq_resume is for kiq initialize.
gfx_v8_0_kcq_resume is for kcq initialize.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Send all kcq unmap_queue packets and then wait for
complete.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
There are no any logical changes here.
1. if kcq can be enabled via kiq, we don't need to
do kiq ring test.
2. amdgpu_ring_test_ring function can be used to
sync the ring complete, remove the duplicate code.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Send all kcq unmap_queue packets and then wait for
complete.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
There are no any logical changes here.
1. if kcq can be enabled via kiq, we don't need to
do kiq ring test.
2. amdgpu_ring_test_ring function can be used to
sync the ring complete, remove the duplicate code.
v2: alloc 6 (not 7) dws for unmap_queues
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
As we have unify powergate_uvd/vce/mmhub to set_powergating_by_smu,
and set_powergating_by_smu was supported by both dpm and powerplay.
so remove the else case.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
when hw_fini/suspend, smu only need to power on uvd block
if uvd pg is supported, don't need to call uvd to do hw_init.
v2: fix typo in patch descriptions and comments.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Tested-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
For SI/Kv, the power state is managed by function
amdgpu_pm_compute_clocks.
when dpm enabled, we should call amdgpu_pm_compute_clocks
to update current power state instand of set boot state.
this change can fix the oops when kfd driver was enabled on Kv.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Tested-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Forgot to add vce pg support via smu for Kaveri/Mullins.
Fixes: 561a5c83eadd ("drm/amd/pp: Unify powergate_uvd/vce/mmhub
to set_powergating_by_smu")
v2: refine patch descriptions suggested by Michel
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Tested-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
when ac/dc switch, driver will be notified by acpi event.
then the power source will be updated. so don't need to
get power source when set power state.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This is required by gfx hw and can fix the rlc hang when
do s3 stree test on Cz/St.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Hang Zhou <hang.zhou@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Set the VM size based on system memory size between the ASIC-specific
limits given by min_vm_size and max_bits. GFXv9 GPUs will keep their
default VM size of 256TB (48 bit). Only older GPUs will adjust VM size
depending on system memory size.
This makes more VM space available for ROCm applications on GFXv8 GPUs
that want to map all available VRAM and system memory in their SVM
address space.
v2:
* Clarify comment
* Round up memory size before >> 30
* Round up automatic vm_size to power of two
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Acked-by: Junwei Zhang <Jerry.Zhang@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
