summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2017-04-13rtlwifi: btcoex: 21a 1ant: add multi port action for miracast and P2PYan-Hsuan Chuang
To support miracast and P2P, the chip may operate under concurrent mode, In this situation, do not aggregate tx packet and properly set the rx aggregation size. We detect it by monitoring the number of link established. Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Pkshih <pkshih@realtek.com> Cc: Birming Chiu <birming@realtek.com> Cc: Shaofu <shaofu@realtek.com> Cc: Steven Ting <steventing@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-04-13rtlwifi: btcoex: 21a 1ant: set antenna control path for PTAYan-Hsuan Chuang
Set antenna control path if PTA is in control of the packet path of wifi and bt. If wifi is turned off, tell the PTA about it. Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Pkshih <pkshih@realtek.com> Cc: Birming Chiu <birming@realtek.com> Cc: Shaofu <shaofu@realtek.com> Cc: Steven Ting <steventing@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-04-13rtlwifi: btcoex: 21a 1ant: remove setting for 2 antennasYan-Hsuan Chuang
The antenna position setting is useless for 1 antenna chip. Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Pkshih <pkshih@realtek.com> Cc: Birming Chiu <birming@realtek.com> Cc: Shaofu <shaofu@realtek.com> Cc: Steven Ting <steventing@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-04-13rtlwifi: btcoex: 21a 1ant: mask profile bit for connect-ildeYan-Hsuan Chuang
Mask out the connect-idle bit. Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Pkshih <pkshih@realtek.com> Cc: Birming Chiu <birming@realtek.com> Cc: Shaofu <shaofu@realtek.com> Cc: Steven Ting <steventing@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-04-13rtlwifi: btcoex: 21a 1ant: coex table setting for new fwYan-Hsuan Chuang
For newer fw, the coex table setting needs to be modified to operate correctly. Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Pkshih <pkshih@realtek.com> Cc: Birming Chiu <birming@realtek.com> Cc: Shaofu <shaofu@realtek.com> Cc: Steven Ting <steventing@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-04-13rtlwifi: btcoex: 21a 1ant: add function to check wifi statusYan-Hsuan Chuang
This function checks if wifi has changed its statusi. It will be needed in the future. Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Pkshih <pkshih@realtek.com> Cc: Birming Chiu <birming@realtek.com> Cc: Shaofu <shaofu@realtek.com> Cc: Steven Ting <steventing@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-04-13rtlwifi: btcoex: 21a 1ant: fw settings for softap modeYan-Hsuan Chuang
For ap mode, adjust fw settings to operate properly. Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Pkshih <pkshih@realtek.com> Cc: Birming Chiu <birming@realtek.com> Cc: Shaofu <shaofu@realtek.com> Cc: Steven Ting <steventing@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-04-13rtlwifi: btcoex: 23b 2ant: some hi-prio pkt will cause hid_existYan-Hsuan Chuang
Clear the hid_exist flag by monitoring the packet counter. Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Pkshih <pkshih@realtek.com> Cc: Birming Chiu <birming@realtek.com> Cc: Shaofu <shaofu@realtek.com> Cc: Steven Ting <steventing@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-04-13rtlwifi: btcoex: 23b 2ant: notify more bt informationYan-Hsuan Chuang
These bt information are displayed in display coex Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Pkshih <pkshih@realtek.com> Cc: Birming Chiu <birming@realtek.com> Cc: Shaofu <shaofu@realtek.com> Cc: Steven Ting <steventing@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-04-13rtlwifi: btcoex: 23b 2ant: fine tune for bt hid_a2dpYan-Hsuan Chuang
Let bt control the aggregation size to improve stability. Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Pkshih <pkshih@realtek.com> Cc: Birming Chiu <birming@realtek.com> Cc: Shaofu <shaofu@realtek.com> Cc: Steven Ting <steventing@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-04-13rtlwifi: btcoex: 23b 2ant: fine tune for bt pan_edr_a2dpYan-Hsuan Chuang
If we don't limit the rx aggregation size, and set tdma instead, the bt profile can get more stable. Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Pkshih <pkshih@realtek.com> Cc: Birming Chiu <birming@realtek.com> Cc: Shaofu <shaofu@realtek.com> Cc: Steven Ting <steventing@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-04-13rtlwifi: btcoex: 23b 2ant: before firmware ready settingsYan-Hsuan Chuang
Before firmware is ready, set GNT_BT to high to let bt transmit Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Pkshih <pkshih@realtek.com> Cc: Birming Chiu <birming@realtek.com> Cc: Shaofu <shaofu@realtek.com> Cc: Steven Ting <steventing@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-04-13rtlwifi: btcoex: 23b 2ant: power on settings for coexYan-Hsuan Chuang
When power on, the wifi could be initiating, force the antenna to transmit bt packets to avoid bt unstable problems Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Pkshih <pkshih@realtek.com> Cc: Birming Chiu <birming@realtek.com> Cc: Shaofu <shaofu@realtek.com> Cc: Steven Ting <steventing@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-04-13rtlwifi: btcoex: 23b 2ant: wifi is not actually off in mp modeYan-Hsuan Chuang
In mp mode, the wifi will not turn off and still has control of the PTA, so the driver needs to distinguish whether it is mp mode or not Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Pkshih <pkshih@realtek.com> Cc: Birming Chiu <birming@realtek.com> Cc: Shaofu <shaofu@realtek.com> Cc: Steven Ting <steventing@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-04-13rtlwifi: btcoex: 23b 2ant: need those information when scanYan-Hsuan Chuang
For scan notify, we need to supervise some registers to make sure that coexistence is operating as we expected. Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Pkshih <pkshih@realtek.com> Cc: Birming Chiu <birming@realtek.com> Cc: Shaofu <shaofu@realtek.com> Cc: Steven Ting <steventing@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-04-13rtlwifi: btcoex: 23b 2ant: remove debugging code for 0x948Yan-Hsuan Chuang
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Pkshih <pkshih@realtek.com> Cc: Birming Chiu <birming@realtek.com> Cc: Shaofu <shaofu@realtek.com> Cc: Steven Ting <steventing@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-04-13rtlwifi: btcoex: 23b 2ant: treat too many low prio packets as retryYan-Hsuan Chuang
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Pkshih <pkshih@realtek.com> Cc: Birming Chiu <birming@realtek.com> Cc: Shaofu <shaofu@realtek.com> Cc: Steven Ting <steventing@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-04-13rtlwifi: btcoex: 23b 2ant: set coex table when wifi is idleYan-Hsuan Chuang
When wifi is idle, the bt should have more resource to transmit. Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Pkshih <pkshih@realtek.com> Cc: Birming Chiu <birming@realtek.com> Cc: Shaofu <shaofu@realtek.com> Cc: Steven Ting <steventing@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-04-13rtlwifi: btcoex: 23b 2ant: set coex table when wifi is linkingYan-Hsuan Chuang
When wifi is under linking process, those packets are important. Mark them as high priority to protect the linking process Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Pkshih <pkshih@realtek.com> Cc: Birming Chiu <birming@realtek.com> Cc: Shaofu <shaofu@realtek.com> Cc: Steven Ting <steventing@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-04-13rtlwifi: btcoex: 23b 2ant: turn off antenna when rssi is too high/lowYan-Hsuan Chuang
For 2-antenna combo card, the signal of the neighbor antenna could be over noise level and cause be severe interference. So we monitor the rssi and turn off one of the antennas when the other is transmitting and the rssi level is beyond a threshold. Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Pkshih <pkshih@realtek.com> Cc: Birming Chiu <birming@realtek.com> Cc: Shaofu <shaofu@realtek.com> Cc: Steven Ting <steventing@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-04-13rtlwifi: btcoex: 23b 2ant: turn off ps and tdma mechanism when in concurrent ↵Yan-Hsuan Chuang
mode When wifi is in concurrent mode, we can not distinguish if it is the real PS or just a fake one by sending null data, so we turn it off in case of miracast scenario. Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Pkshih <pkshih@realtek.com> Cc: Birming Chiu <birming@realtek.com> Cc: Shaofu <shaofu@realtek.com> Cc: Steven Ting <steventing@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-04-13rtlwifi: btcoex: 23b 2ant: let bt transmit when hw initialisation doneYan-Hsuan Chuang
During hw initialisation, wifi may be ready after bt has already been ready, which causes bt to act abnormally. To avoid this, set GNT_BT to high during hw init. Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Cc: Stable <stable@vger.kernel.org> Cc: Pkshih <pkshih@realtek.com> Cc: Birming Chiu <birming@realtek.com> Cc: Shaofu <shaofu@realtek.com> Cc: Steven Ting <steventing@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-04-13rtlwifi: btcoex: 23b 2ant: tell fw if external or internal switch is usedYan-Hsuan Chuang
Some chips use an external antenna switch, but fw may not realize it. Here we tell fw exactly that which type of switch we are using. Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Pkshih <pkshih@realtek.com> Cc: Birming Chiu <birming@realtek.com> Cc: Shaofu <shaofu@realtek.com> Cc: Steven Ting <steventing@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-04-13rtlwifi: btcoex: 23b 2ant: workaround for bt a2dp and hidYan-Hsuan Chuang
For a2dp and hid, we need extra process to avoid voice degradation Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Pkshih <pkshih@realtek.com> Cc: Birming Chiu <birming@realtek.com> Cc: Shaofu <shaofu@realtek.com> Cc: Steven Ting <steventing@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-04-13rtlwifi: btcoex: 23b 2ant: check more cases when bt is queuingYan-Hsuan Chuang
If bt is queing, we need to set the packet priority properly. Originally we only consider if wifi was connected or not, but now we also consider if bt is under abnormal scan or wifi is scanning, roaming or linking, and set the coex table. Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Pkshih <pkshih@realtek.com> Cc: Birming Chiu <birming@realtek.com> Cc: Shaofu <shaofu@realtek.com> Cc: Steven Ting <steventing@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-04-13rtlwifi: btcoex: 23b 2ant: add pnp notidy to avoid LPS/IPS mismatchYan-Hsuan Chuang
When driver is going to sleep, it does not leave LPS/IPS, thus the BTCoex may have mismatch when driver wakes up. To avoid that, BTCoex needs to clear the IPS/LPS state when it receives a pnp notify, then it can properly set up the hw when driver wakes up. Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Cc: Pkshih <pkshih@realtek.com> Cc: Birming Chiu <birming@realtek.com> Cc: Shaofu <shaofu@realtek.com> Cc: Steven Ting <steventing@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-04-13rtlwifi: btcoex: 23b 2ant: fix PTA unstable problem when hw initYan-Hsuan Chuang
In the hardware initialisation stage, the PTA circuits may be unstable, so we reset it after 6 secs to fix the problem. Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Cc: Pkshih <pkshih@realtek.com> Cc: Birming Chiu <birming@realtek.com> Cc: Shaofu <shaofu@realtek.com> Cc: Steven Ting <steventing@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-04-13rtlwifi: btcoex: 23b 2ant: more cases for adjusting tdma durationYan-Hsuan Chuang
These cases are for the btcoex to tune the performance Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Cc: Pkshih <pkshih@realtek.com> Cc: Birming Chiu <birming@realtek.com> Cc: Shaofu <shaofu@realtek.com> Cc: Steven Ting <steventing@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-04-13rtlwifi: btcoex: 23b 2ant: detect ap num and set GNT_BT properlyYan-Hsuan Chuang
If ap num < 10, let wifi and bt transmit simultaneously, otherwise set wifi into standy when bt is transmitting Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Pkshih <pkshih@realtek.com> Cc: Birming Chiu <birming@realtek.com> Cc: Shaofu <shaofu@realtek.com> Cc: Steven Ting <steventing@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-04-13rtlwifi: btcoex: 23b 2ant: rename tdma_adj_type to ps_tdma_du_adj_typeYan-Hsuan Chuang
The variable is for PS tdma duration adjust, so rename it to clearly to specify its usage. Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Pkshih <pkshih@realtek.com> Cc: Birming Chiu <birming@realtek.com> Cc: Shaofu <shaofu@realtek.com> Cc: Steven Ting <steventing@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-04-13rtlwifi: btcoex: 23b 2ant: check PS state before setting tdma durationYan-Hsuan Chuang
For time division multiple access, the wifi and bt take turns to transmit, but we need to let AP know that wifi is under standby mode by sending null data to "pretend" entering power saving state using lps rpwm. But, the fw does not know if it is the actual power saving mode or just a fake one to cheat to the AP. Hence, before fw setting the tdma duration, the fw needs the driver to check the power saving state first. Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Pkshih <pkshih@realtek.com> Cc: Birming Chiu <birming@realtek.com> Cc: Shaofu <shaofu@realtek.com> Cc: Steven Ting <steventing@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-04-13brcmfmac: only add channels and ssids once in scan requestArend Van Spriel
When receiving pno results there may be duplicate channels and/or ssids. Assure each is added only once when preparing the internal escan request. Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com> Reviewed-by: Franky Lin <franky.lin@broadcom.com> Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-04-13brcmfmac: remove bogus check in scheduled scan result handlerArend Van Spriel
Checking whether the address of an array element is null is bogus so removing it. Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com> Reviewed-by: Franky Lin <franky.lin@broadcom.com> Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-04-13brcmfmac: add length checks in scheduled scan result handlerArend Van Spriel
Assure the event data buffer is long enough to hold the array of netinfo items and that SSID length does not exceed the maximum of 32 characters as per 802.11 spec. Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com> Reviewed-by: Franky Lin <franky.lin@broadcom.com> Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-04-13brcmfmac: remove reference to fwsignal data from struct brcmf_pubArend Van Spriel
The fwsignal module is part of the bcdc protocol and as such does its instance data is not needed in core structure. Moving it into struct brcmf_bcdc instead. Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com> Reviewed-by: Franky Lin <franky.lin@broadcom.com> Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-04-13brcmfmac: ignore interfaces when fwsignal is disabledArend Van Spriel
When brcmf_fws_add_interface() is called the struct brcmf_if::fws_desc field is initialized regardless the state of the fwsignal functionality, ie. the fcmode. This is not needed when fcmode is NONE, which is the default mode. Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com> Reviewed-by: Franky Lin <franky.lin@broadcom.com> Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-04-13brcmfmac: rename brcmf_fws_{de,}init to brcmf_fws{at,de}tachArend Van Spriel
This is a non-functional change to align the fwsignal module to the naming pattern used throughout the driver. Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com> Reviewed-by: Franky Lin <franky.lin@broadcom.com> Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-04-13brcmfmac: properly align buffers on certain platforms with 64 bit DMAHeiner Kallweit
Systems with 64 bit DMA at least partially require buffers to be used for DMA to be 8-byte-aligned. One example is Amlogic Meson GX. Switching the MMC/SDIO driver for this platform to SG DMA mode resulted in problems due to unaligned buffers. Fortunately the brcmfmac driver has a global define for the alignment. Changing it to 8 fixed the issues with Meson GX. Suggested-by: Helmut Klein <hgkr.klein@gmail.com> Tested-by: Helmut Klein <hgkr.klein@gmail.com> Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-04-13mwifiex: Fix invalid port issueGanapathi Bhat
We have to use start port, for TX/RX of single packet, instead of current aggregating port. This will fix SDIO CMD53(TX/RX) returning -ETIMEDOUT and halting the data path. Fixes: 0cb52aac4d19 ("mwifiex: do not set multiport flag for tx/rx single packet") Signed-off-by: Ganapathi Bhat <gbhat@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-04-13cpupower: Fix turbo frequency reporting for pre-Sandy Bridge coresBen Hutchings
The switch that conditionally sets CPUPOWER_CAP_HAS_TURBO_RATIO and CPUPOWER_CAP_IS_SNB flags is missing a break, so all cores get both flags set and an assumed base clock of 100 MHz for turbo values. Reported-by: GSR <gsr.bugs@infernal-iceberg.com> Tested-by: GSR <gsr.bugs@infernal-iceberg.com> References: https://bugs.debian.org/859978 Fixes: 8fb2e440b223 (cpupower: Show Intel turbo ratio support via ...) Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-04-13Merge branch 'turbostat' of ↵Rafael J. Wysocki
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux Pull turbostat utility fixes for v4.11 from Len Brown. * 'turbostat' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux: tools/power turbostat: update version number tools/power turbostat: fix impossibly large CPU%c1 value tools/power turbostat: turbostat.8 add missing column definitions tools/power turbostat: update HWP dump to decimal from hex tools/power turbostat: enable package THERM_INTERRUPT dump tools/power turbostat: show missing Core and GFX power on SKL and KBL tools/power turbostat: bugfix: GFXMHz column not changing
2017-04-13wil6210: prevent access to 11AD device if resume failsMaya Erez
In case wil6210 resume fails, wil6210 suspend function will try to access the suspended device in the next kernel suspend. To prevent that, add wil_status_suspended flag to indicate if the device is already suspended and clear it only if the resume succeeds. Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2017-04-13wil6210: fix array out of bounds access in pmcDedy Lansky
Array index 'i' is used before limits check. Fix this by doing limits check first. Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com> Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2017-04-13wil6210: remove HALP voting in debugfs ioblobMaya Erez
debugfs ioblob function is called by the FW logs scripts to copy the FW logs via PCIe. As the FW logs collection is done in parallel to the operational 11AD actions, the HALP voting can take place during 11AD reset flow and other sensitive scenarios. To prevent that, remove HALP voting from the ioblob function. Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2017-04-13wil6210: fix memory access violation in wil_memcpy_from/toio_32Dedy Lansky
In case count is not multiple of 4, there is a read access in wil_memcpy_toio_32() from outside src buffer boundary. In wil_memcpy_fromio_32(), in case count is not multiple of 4, there is a write access to outside dst io memory boundary. Fix these issues with proper handling of the last 1 to 4 copied bytes. Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com> Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2017-04-13wil6210: fix check for sparrow D0 FW fileHamad Kadmany
Driver fails to load FW for sparrow D0 devices in some cases. Fix this by returning correct value from wil_fw_verify_file_exists when D0 FW file is not detected for any reason. Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com> Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2017-04-13wil6210: protect against sporadic interrupt during suspend flowMaya Erez
During the suspend flow, wil6210 HW can send sporadic interrupts, while PCIe bus is not operational. To prevent that, keep the interrupts disabled during the suspend flow and re-enable them only after PCIe enablement in resume. Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2017-04-13wil6210: fix protection against connections during resetHamad Kadmany
Existing code that ignores connection events during reset flow will never take effect since it locks the same mutex taken by the reset flow. In addition, in case of unsolicited disconnect events ignore those as well since device is about to get reset. Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com> Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2017-04-13wil6210: align to latest auto generated wmi.hDedy Lansky
Align to latest version of the auto generated wmi file describing the interface with FW Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com> Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2017-04-13wil6210: support 8KB RX buffersLior David
The 11ad spec requires 11ad devices to be able to receive 8KB packets over the air. Currently this is only possible by loading the driver with mtu_max=7912 but this also forces a smaller block ACK window size which reduces performance for stations which transmit normal sized packets (<2KB). Fix this problem as follows: 1. Add a module parameter rx_large_buf that when set, will allocate 8KB RX buffers regardless of mtu_max setting. 2. When receiving block ACK request agree to any window size not above our maximum, regardless of the mtu_max setting. This means if the other side transmits small packets (2KB) it can still set up block ACK with a large window size, and get better performance. Signed-off-by: Lior David <qca_liord@qca.qualcomm.com> Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
generated by cgit (git 2.34.1) at 2025-09-16 20:45:53 +0000