| Age | Commit message (Collapse) | Author |
|---|
|
Take into a function the common code structure of opening
a side set of channels followed by a call to apply them.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
In previous patch, driver added new speed modes: 50Gbps per lane support
for 50G/100G/200G. This patch modifies mlx5e_get_link_ksettings and
mlx5e_set_link_ksettings to set and get these link modes via ethtool.
In order to do so, added mapping of new HW bits to ethtool bitmap and
enforce mutual exclusion between extended link modes and previously
defined link modes.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Added support for 50Gbps per lane link modes. Define various 50G, 100G
and 200G link modes using it.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sschmidt/wpan-next
Stefan Schmidt says:
====================
pull-request: ieee802154-next 2019-02-19
An update from ieee802154 for *net-next*
Another quite quite cycle in the ieee802154 subsystem.
Peter did a rework of the IP frag queue handling to make it use rbtree and get
in line with the core IPv4 and IPv6 implementatiosn in the kernel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is to do code cleanup for ns83820_probe_phy().
It deletes unused variable 'first', commented out code,
and the pointless 'for' loop.
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
when capable check failed, dev_put should
be call before return -EACCES.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RGMII_ID specifies that we should have internal delay, so resurrect the
delay addition routine but under the RGMII_ID mode.
Fixes: 40269aa9f40a ("net: dsa: qca8k: disable delay for RGMII mode")
Tested-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When fail, translate_desc() returns negative value, otherwise the
number of iovs. So we should fail when the return value is negative
instead of a blindly check against zero.
Detected by CoverityScan, CID# 1442593: Control flow issues (DEADCODE)
Fixes: cc5e71075947 ("vhost: log dirty page correctly")
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reported-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The skb->queue_mapping already have read access, via __sk_buff->queue_mapping.
This patch allow BPF tc qdisc clsact write access to the queue_mapping via
tc_cls_act_is_valid_access. Also handle that the value NO_QUEUE_MAPPING
is not allowed.
It is already possible to change this via TC filter action skbedit
tc-skbedit(8). Due to the lack of TC examples, lets show one:
# tc qdisc add dev ixgbe1 clsact
# tc filter add dev ixgbe1 ingress matchall action skbedit queue_mapping 5
# tc filter list dev ixgbe1 ingress
The most common mistake is that XPS (Transmit Packet Steering) takes
precedence over setting skb->queue_mapping. XPS is configured per DEVICE
via /sys/class/net/DEVICE/queues/tx-*/xps_cpus via a CPU hex mask. To
disable set mask=00.
The purpose of changing skb->queue_mapping is to influence the selection of
the net_device "txq" (struct netdev_queue), which influence selection of
the qdisc "root_lock" (via txq->qdisc->q.lock) and txq->_xmit_lock. When
using the MQ qdisc the txq->qdisc points to different qdiscs and associated
locks, and HARD_TX_LOCK (txq->_xmit_lock), allowing for CPU scalability.
Due to lack of TC examples, lets show howto attach clsact BPF programs:
# tc qdisc add dev ixgbe2 clsact
# tc filter add dev ixgbe2 egress bpf da obj XXX_kern.o sec tc_qmap2cpu
# tc filter list dev ixgbe2 egress
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Introduce cant_sleep() macro for annotation of functions that
cannot sleep.
Use it in BPF_PROG_RUN to catch execution of BPF programs in
preemptable context.
Suggested-by: Jann Horn <jannh@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
[Why]
The visual corruption due to low display clock value.
Observed on Carrizo 4K@60Hz.
[How]
There was earlier patch for dce_update_clocks:
Adding +15% workaround also to to dce11_update_clocks
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
drm_dp_mst_topology_mgr_suspend() is added into the new reboot
sequence, which disables the UP request at the beginning.
Therefore sideband messages are blocked.
[How]
Finish MST sideband message transaction before UP request is
suppressed.
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
According to hardware engineer, WRITE_BURST_LENGTH [9:8] in register
SDMA0_CHICKEN_BITS need to change to 3 for better performance
Signed-off-by: shaoyunl <shaoyun.liu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Based on a similar patch from Rafael for radeon.
When using ATPX to control dGPU power, the state is not retained
across suspend and resume cycles by default. This can probably
be loosened for Hybrid Graphics (_PR3) laptops where I think the
state is properly retained.
Fixes: c62ec4610c40 ("PM / core: Fix direct_complete handling for devices with no callbacks")
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
On HP ProBook 4540s, if PM-runtime is enabled in the radeon driver
and the direct-complete optimization is used for the radeon device
during system-wide suspend, the system doesn't resume.
Preventing direct-complete from being used with the radeon device by
setting the DPM_FLAG_NEVER_SKIP driver flag for it makes the problem
go away, which indicates that direct-complete is not safe for the
radeon driver in general and should not be used with it (at least
for now).
This fixes a regression introduced by commit c62ec4610c40
("PM / core: Fix direct_complete handling for devices with no
callbacks") which allowed direct-complete to be applied to
devices without PM callbacks (again) which in turn unlocked
direct-complete for radeon on HP ProBook 4540s.
Fixes: c62ec4610c40 ("PM / core: Fix direct_complete handling for devices with no callbacks")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=201519
Reported-by: Ярослав Семченко <ukrkyi@gmail.com>
Tested-by: Ярослав Семченко <ukrkyi@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Michael Chan says:
====================
bnxt_en: Update for net-next.
This series includes the usual firmware spec. update, a PCI ID addition,
enhancements for VF trust, MDIO read/write for external PHY, and
fixing the return code when TC flow offload fails.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver returns -ENOSPC when tc_can_offload() check fails. Since that
routine checks for flow parameters that are not supported by the driver,
we should return the more appropriate -EOPNOTSUPP.
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for SIOCGMIIREG and SIOCSMIIREG ioctls to
mdio read/write to external PHY.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Newer firmware understands the concept of a trusted VF, so propagate the
trusted VF attribute set by the PF admin. to the firmware. Also, check
the firmware trusted setting when considering the VF MAC address change
and reporting the trusted setting to the user.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for BCM957504 with device ID 1751
Signed-off-by: Erik Burrows <erik.burrows@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Firmware error recover is the major change in this spec.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Each tls context maintains two cipher contexts (one each for tx and rx
directions). For each tls session, the constants such as protocol
version, ciphersuite, iv size, associated data size etc are same for
both the directions and need to be stored only once per tls context.
Hence these are moved from 'struct cipher_context' to 'struct
tls_prot_info' and stored only once in 'struct tls_context'.
Signed-off-by: Vakul Garg <vakul.garg@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
The PHY must add both tx and rx delay and not only on the tx clock.
The board uses AR8031_AL1A PHY where the rx delay is enabled by default,
the tx dealy is disabled.
The reason why rgmii-txid worked because the rx delay was not disabled by
the driver so essentially we ended up with rgmii-id PHY mode.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The PHY must add both tx and rx delay and not only on the tx clock.
The board uses AR8031_AL1A PHY where the rx delay is enabled by default,
the tx dealy is disabled.
The reason why rgmii-txid worked because the rx delay was not disabled by
the driver so essentially we ended up with rgmii-id PHY mode.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
bpftool has support for attach types "stream_verdict" and
"stream_parser" but the documentation was referring to them as
"skb_verdict" and "skb_parse". The inconsistency comes from commit
b7d3826c2ed6 ("bpf: bpftool, add support for attaching programs to
maps").
This patch changes the documentation to match the implementation:
- "bpftool prog help"
- man pages
- bash completion
Signed-off-by: Alban Crequy <alban@kinvolk.io>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Add driver for the SiFive SPI controller
on the HiFive Unleashed board.
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Yash Shah <yash.shah@sifive.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
DT documentation for SPI controller added.
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Yash Shah <yash.shah@sifive.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Currently rdev is dereferenced when assigning desc before rdev is null
checked, this is leading to static analysis warnings. However, rdev
can never be null, so the null check is redundant and can be removed.
Detected by CoverityScan, CID#1476031 ("Dereference before null check")
Fixes: 77e3e3b165db ("regulator: axp20x: add software based soft_start for AXP209 LDO3")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
set_current_limit
Selecting the minimal value is only true for voltage regulators.
For current regulators the maximum in the given range should be
selected instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
set_current_limit
Selecting the minimal value is only true for voltage regulators.
For current regulators the maximum in the given range should be
selected instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Fix off-by-one while iterating current_limits array.
The valid index should be 0 ~ n_current_limits -1.
Fixes: c90456e36d9c ("regulator: pv88090: new regulator driver")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Fix off-by-one while iterating current_limits array.
The valid index should be 0 ~ n_current_limits -1.
Fixes: 99cf3af5e2d5 ("regulator: pv88080: new regulator driver")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Fix off-by-one while iterating current_limits array.
The valid index should be 0 ~ n_current_limits -1.
Fixes: f307a7e9b7af ("regulator: pv88060: new regulator driver")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We do not need separate lines for calculating register values.
Also add comment that value is different than in vendor driver.
Suggested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The TX_PIN_CFG_RFRX_EN bit was not set on other devices than MT7620,
restore old behavaviour since setting this bit maight not be
correct for older devices.
Fixes: 41977e86c984 ("rt2x00: add support for MT7620")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Do not enable TX_PIN_CFG_LNA_PE_A* bits for 2.4GHz band and
vice versa TX_PIN_CFG_LNA_PE_G* bits for 5GHz.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Register 66 was causing issues on RT6352 if set to the same value as
in MTK driver. With 1c reg value device was working fine in both HT20
and HT40 modes.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Remove band check from rf53xx channel config routine since all chips
using it are single band.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The parameter order for clamp is supposed to be clamp(value, low, high).
When we write it in this order it's equivalent to
min(head->plcp[3] & 0x7f, 75) which works in this context where the min
is zero. But it's not a correct use of the API.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtl818x/rtl8180/dev.c: In function 'rtl8180_probe':
drivers/net/wireless/realtek/rtl818x/rtl8180/dev.c:1727:15: warning:
variable 'io_addr' set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtl818x/rtl8180/dev.c:1726:16: warning:
variable 'mem_addr' set but not used [-Wunused-but-set-variable]
They're never used since introduction.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Replace hard coded function name with __func__, to
improve robustness and to conform to the Linux kernel coding
style. Issue found using checkpatch.
Signed-off-by: Keyur Patel <iamkeyur96@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
As it is, doing something like
# iw phy phy0 interface add foobar type ibss
on a firmware that doesn't have ad-hoc support just yields failures of
HostCmd_CMD_SET_BSS_MODE, which happened to return a '-1' error code
(-EPERM? not really right...) and sometimes may even crash the firmware
along the way.
Let's parse the firmware capability flag while registering the wiphy, so
we don't allow attempting IBSS at all, and we get a proper -EOPNOTSUPP
from nl80211 instead.
Fixes: e267e71e68ae ("mwifiex: Disable adhoc feature based on firmware capability")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
NL80211_TX_POWER_LIMITED was treated as NL80211_TX_POWER_AUTOMATIC,
which is the opposite of what should happen and can cause nasty
regulatory problems.
if/else converted to a switch without default to make gcc warn
on unhandled enum values.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/marvell/libertas_tf/main.c: In function 'lbtf_rx':
drivers/net/wireless/marvell/libertas_tf/main.c:554:15: warning:
variable 'flags' set but not used [-Wunused-but-set-variable]
It never used and can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Steve deRosier <derosier@cal-sierra.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Instead of exposing the signal-to-noise ration, calculate the actual signal
level taking the noise floor into account.
Also, flip the SIGNAL_DBM bit on, so that mac80211 exposes the signal
level along with the station info in scan results. This fills
NetworkManager's "nmcli d wifi output" output with colors, bars and joy.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Steve deRosier <derosier@cal-sierra.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Also, turn it to a dev_info() to make checkpatch.pl happy.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Steve deRosier <derosier@cal-sierra.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
It doesn't make sense and the USB core warns on each submit of such
URB, easily flooding the message buffer with tracebacks.
Analogous issue was fixed in regular libertas driver in commit 6528d8804780
("libertas: don't set URB_ZERO_PACKET on IN USB transfer").
Cc: stable@vger.kernel.org
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Steve deRosier <derosier@cal-sierra.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Logging each and every command response is way too much for INFO level.
Silence this, unless CONFIG_LIBERTAS_THINFIRM_DEBUG has been enabled.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Steve deRosier <derosier@cal-sierra.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/rsi/rsi_91x_main.c: In function 'rsi_prepare_skb':
drivers/net/wireless/rsi/rsi_91x_main.c:127:24: warning:
variable 'vif' set but not used [-Wunused-but-set-variable]
drivers/net/wireless/rsi/rsi_91x_main.c:124:28: warning:
variable 'info' set but not used [-Wunused-but-set-variable]
They're not used any more since 160ee2a11ce0 ("rsi: fill rx_params only once.")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
