| Age | Commit message (Collapse) | Author |
|---|
|
|
|
Currently we already have two pin configuration related callbacks
available for GPIO chips .set_single_ended() and .set_debounce(). In
future we expect to have even more, which does not scale well if we need
to add yet another callback to the GPIO chip structure for each possible
configuration parameter.
Better solution is to reuse what we already have available in the
generic pinconf.
To support this, we introduce a new .set_config() callback for GPIO
chips. The callback takes a single packed pin configuration value as
parameter. This can then be extended easily beyond what is currently
supported by just adding new types to the generic pinconf enum.
If the GPIO driver is backed up by a pinctrl driver the GPIO driver can
just assign gpiochip_generic_config() (introduced in this patch) to
.set_config and that will take care configuration requests are directed
to the pinctrl driver.
We then convert the existing drivers over .set_config() and finally
remove the .set_single_ended() and .set_debounce() callbacks.
Suggested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
When a GPIO driver is backed by a pinctrl driver the GPIO driver
sometimes needs to call the pinctrl driver to configure certain things,
like whether the pin is used as input or output. In addition to this
there are other configurations applicable to GPIOs such as setting
debounce time of the GPIO.
To support this we introduce a new function pinctrl_gpio_set_config()
that can be used by gpiolib based driver to pass configuration requests
to the backing pinctrl driver.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The current pinconf packed format allows only 16-bit argument limiting
the maximum value 65535. For most types this is enough. However,
debounce time can be in range of hundreths of milliseconds in case of
mechanical switches so we cannot represent the worst case using the
current format.
In order to support larger values change the packed format so that the
lower 8 bits are used as type which leaves 24 bits for the argument.
This allows representing values up to 16777215 and debounce times up to
16 seconds.
We also convert the existing users to use 32-bit integer when extracting
argument from the packed configuration value.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
A cleanup caused a harmless warning:
drivers/pinctrl/mvebu/pinctrl-kirkwood.c: In function 'kirkwood_pinctrl_probe':
drivers/pinctrl/mvebu/pinctrl-kirkwood.c:460:19: error: unused variable 'res' [-Werror=unused-variable]
The obvious fix is to remove the declaration of the now unused
variable.
Fixes: ad9ec4ecee68 ("pinctrl: mvebu: switch drivers to generic simple mmio")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This is less straight-forward than one would hope, as some banks only
have 4 pins rather than 8, others are output only, yet more (W and
X, already supported) are input-only, and in the case of the g4 SoC bank
AC doesn't exist.
Add some structs to describe the varying properties of different banks
and integrate mechanisms to deny requests for unsupported
configurations.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Incorrect video output configuration bits were being tested on pins in
GPIO banks AA and AB for the ROM{8,16} mux functions. The ROM{8,16}
functions are the highest priority for the relevant pins and also the
default function, so we require the relevant video output configuration
be disabled to mux GPIO functionality. As the wrong bits were being
tested a GPIO export would succeed but leave the pin in an unresponsive
state (i.e. value updates were ignored).
This misbehaviour was discovered as part of extending the GPIO
controller's support to cover banks Y, Z, AA, AB and AC (AC in the case
of the g5 SoC).
Fixes: 6d329f14a75f ("pinctrl: aspeed-g4: Add mux configuration for all pins")
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Aspeed SoCs have more GPIOs than can be represented with A-Z. The
documentation uses two letter names such as AA and AB, so make the names
a three-character array in the bank struct to accommodate this.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The MSM pinctrl driver currently implements an irq_chip for handling
GPIO interrupts; due to how irq_chip handling is done, it's necessary
for the irq_chip methods to be invoked from hardirq context, even on a
a real-time kernel. Because the spinlock_t type becomes a "sleeping"
spinlock w/ RT kernels, it is not suitable to be used with irq_chips.
A quick audit of the operations under the lock reveal that they do only
minimal, bounded work, and are therefore safe to do under a raw
spinlock.
On real-time kernels, this fixes an OOPs which looks like the following,
as reported by Brian Wrenn:
kernel BUG at kernel/locking/rtmutex.c:1014!
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
Modules linked in: spidev_irq(O) smsc75xx wcn36xx [last unloaded: spidev]
CPU: 0 PID: 1163 Comm: irq/144-mmc0 Tainted: G W O 4.4.9-linaro-lt-qcom #1
PC is at rt_spin_lock_slowlock+0x80/0x2d8
LR is at rt_spin_lock_slowlock+0x68/0x2d8
[..]
Call trace:
rt_spin_lock_slowlock
rt_spin_lock
msm_gpio_irq_ack
handle_edge_irq
generic_handle_irq
msm_gpio_irq_handler
generic_handle_irq
__handle_domain_irq
gic_handle_irq
Reported-by: Brian Wrenn <dcbrianw@gmail.com>
Tested-by: Brian Wrenn <dcbrianw@gmail.com>
Signed-off-by: Julia Cartwright <julia@ni.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Return proper error code in case of memory allocation failure.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Memory subsystem already prints message about failed memory
allocation, there is no need to do it in the drivers.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add missing compatible id for Exynos3250 SoC to device tree docs.
Exynos pin control driver supports it since commit d97f5b9804bfcdc1
("pinctrl: exynos: Add driver data for Exynos3250").
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
If we try to allocate memory pages to back an xfs_buf that we're trying
to read, it's possible that we'll be so short on memory that the page
allocation fails. For a blocking read we'll just wait, but for
readahead we simply dump all the pages we've collected so far.
Unfortunately, after dumping the pages we neglect to clear the
_XBF_PAGES state, which means that the subsequent call to xfs_buf_free
thinks that b_pages still points to pages we own. It then double-frees
the b_pages pages.
This results in screaming about negative page refcounts from the memory
manager, which xfs oughtn't be triggering. To reproduce this case,
mount a filesystem where the size of the inodes far outweighs the
availalble memory (a ~500M inode filesystem on a VM with 300MB memory
did the trick here) and run bulkstat in parallel with other memory
eating processes to put a huge load on the system. The "check summary"
phase of xfs_scrub also works for this purpose.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
|
|
Simon Wunderlich says:
====================
Here is a batman-adv bugfix:
- fix reference count handling on fragmentation error, by Sven Eckelmann
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit 17bedab27231 ("bpf: xdp: Allow head adjustment in XDP prog")
added a new XDP helper to prepend and remove data from a frame.
Make virtio_net reject programs making use of this helper until
proper support is added.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the small buffer case during driver unload we currently use
put_page instead of dev_kfree_skb. Resolve this by adding a check
for virtnet mode when checking XDP queue type. Also name the
function so that the code reads correctly to match the additional
check.
Fixes: bb91accf2733 ("virtio-net: XDP support for small buffers")
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Hayes Wang says:
====================
r8152: fix scheduling napi
v3:
simply the argument for patch #3. Replace &tp->napi with napi.
v2:
Add smp_mb__after_atomic() for patch #1.
v1:
Scheduling the napi during the following periods would let it be ignored.
And the events wouldn't be handled until next napi_schedule() is called.
1. after napi_disable and before napi_enable().
2. after all actions of napi function is completed and before calling
napi_complete().
If no next napi_schedule() is called, tx or rx would stop working.
In order to avoid these situations, the followings solutions are applied.
1. prevent start_xmit() from calling napi_schedule() during runtime suspend
or after napi_disable().
2. re-schedule the napi for tx if it is necessary.
3. check if any rx is finished or not after napi_enable().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Schedule the napi after napi_enable() for rx, if it is necessary.
If the rx is completed when napi is disabled, the sheduling of napi
would be lost. Then, no one handles the rx packet until next napi
is scheduled.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Re-schedule napi after napi_complete() for tx, if it is necessay.
In r8152_poll(), if the tx is completed after tx_bottom() and before
napi_complete(), the scheduling of napi would be lost. Then, no
one handles the next tx until the next napi_schedule() is called.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Stop the tx when the napi is disabled to prevent napi_schedule() is
called.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adjust the setting of the flag of SELECTIVE_SUSPEND to prevent start_xmit()
from calling napi_schedule() directly during runtime suspend.
After calling napi_disable() or clearing the flag of WORK_ENABLE,
scheduling the napi is useless.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When system enters VLLS mode, module power is turned off. As a result,
all registers are reset to HW default value. After exiting VLLS mode,
registers are still in default mode. As a result, the pinctrl settings
are incorrect, which will affect the module function.
The patch recovers the pinctrl setting when exit VLLS mode.
Signed-off-by: Gao Pan <pandy.gao@nxp.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
[wsa: added missing include]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
This seems to break reboot on some evergreen systems.
bugs:
https://bugs.freedesktop.org/show_bug.cgi?id=99524
https://bugzilla.kernel.org/show_bug.cgi?id=192271
This reverts commit a481daa88fd4d6b54f25348972bba10b5f6a84d0.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
The cadence I2C driver calls cdns_i2c_writereg(..) to setup a workaround
in the controller, but did so after calling i2c_add_adapter() which starts
probing devices on the bus. Change the order so that the configuration is
completely finished before using the adapter.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
This reverts commit 3846fd9b86001bea171943cc3bb9222cb6da6b42.
There were some precursor commits missing for this around connector
locking, we should probably merge Lyude's nouveau avoid the problem patch.
|
|
Commit 448b4482c671 ("net: dsa: Add lockdep class to tx queues to avoid
lockdep splat") removed the netif_device_detach() call done in
dsa_slave_suspend() which is necessary, and paired with a corresponding
netif_device_attach(), bring it back.
Fixes: 448b4482c671 ("net: dsa: Add lockdep class to tx queues to avoid lockdep splat")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Geert Uytterhoeven says:
====================
net: phy: leds: Fix truncated LED trigger names and crashes
I started seeing crashes during s2ram and poweroff on all my ARM boards,
like:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
...
[<c04116d4>] (__list_del_entry_valid) from [<c05e8948>] (led_trigger_unregister+0x34/0xcc)
[<c05e8948>] (led_trigger_unregister) from [<c05336c4>] (phy_led_triggers_unregister+0x28/0x34)
[<c05336c4>] (phy_led_triggers_unregister) from [<c0531d44>] (phy_detach+0x30/0x74)
[<c0531d44>] (phy_detach) from [<c0538bdc>] (sh_eth_close+0x64/0x9c)
[<c0538bdc>] (sh_eth_close) from [<c04d4ce0>] (dpm_run_callback+0x48/0xc8)
or:
list_del corruption. prev->next should be dede6540, but was 2e323931
------------[ cut here ]------------
kernel BUG at lib/list_debug.c:52!
...
[<c02f6d70>] (__list_del_entry_valid) from [<c0425168>] (led_trigger_unregister+0x34/0xcc)
[<c0425168>] (led_trigger_unregister) from [<c03a05a0>] (phy_led_triggers_unregister+0x28/0x34)
[<c03a05a0>] (phy_led_triggers_unregister) from [<c039ec04>] (phy_detach+0x30/0x74)
[<c039ec04>] (phy_detach) from [<c03a4fc0>] (sh_eth_close+0x6c/0xa4)
[<c03a4fc0>] (sh_eth_close) from [<c0483234>] (__dev_close_many+0xac/0xd0)
As the only clue was a kernel message like
sh-eth ee700000.ethernet eth0: No phy led trigger registered for speed(100)
I had to bisected this, leading to commit 4567d686f5c6d955 ("phy:
increase size of MII_BUS_ID_SIZE and bus_id"). Reverting that commit
fixed the issue.
More investigation revealed the crashes are due to the combination of
two things:
- Truncated LED trigger names, leading to duplicate names, and
registration failures,
- Bad error handling in case of registration failures.
Both are fixed by this patch series.
Changes compared to v1:
- Add Reviewed-by,
- New patch "net: phy: leds: Break dependency of phy.h on
phy_led_triggers.h",
- Drop moving the include of <linux/phy_led_triggers.h>, as
<linux/phy.h> no longer includes it,
- #include <linux/phy.h> from <linux/phy_led_triggers.h>.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 4567d686f5c6d955 ("phy: increase size of MII_BUS_ID_SIZE and
bus_id") increased the size of MII bus IDs, but forgot to update the
private definition in <linux/phy_led_triggers.h>.
This may cause:
1. Truncation of LED trigger names,
2. Duplicate LED trigger names,
3. Failures registering LED triggers,
4. Crashes due to bad error handling in the LED trigger failure path.
To fix this, and prevent the definitions going out of sync again in the
future, let the PHY LED trigger code use the existing MII_BUS_ID_SIZE
definition.
Example:
- Before I had triggers "ee700000.etherne:01:100Mbps" and
"ee700000.etherne:01:10Mbps",
- After the increase of MII_BUS_ID_SIZE, both became
"ee700000.ethernet-ffffffff:01:" => FAIL,
- Now, the triggers are "ee700000.ethernet-ffffffff:01:100Mbps" and
"ee700000.ethernet-ffffffff:01:10Mbps", which are unique again.
Fixes: 4567d686f5c6d955 ("phy: increase size of MII_BUS_ID_SIZE and bus_id")
Fixes: 2e0bc452f4721520 ("net: phy: leds: add support for led triggers on phy link state change")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
<linux/phy.h> includes <linux/phy_led_triggers.h>, which is not really
needed. Drop the include from <linux/phy.h>, and add it to all users
that didn't include it explicitly.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
phy_attach_direct() ignores errors returned by
phy_led_triggers_register(). I think that's OK, as LED triggers can be
considered a non-critical feature.
However, this causes problems later:
- phy_led_trigger_change_speed() will access the array
phy_device.phy_led_triggers, which has been freed in the error path
of phy_led_triggers_register(), which may lead to a crash.
- phy_led_triggers_unregister() will access the same array, leading to
crashes during s2ram or poweroff, like:
Unable to handle kernel NULL pointer dereference at virtual address
00000000
...
[<c04116d4>] (__list_del_entry_valid) from [<c05e8948>] (led_trigger_unregister+0x34/0xcc)
[<c05e8948>] (led_trigger_unregister) from [<c05336c4>] (phy_led_triggers_unregister+0x28/0x34)
[<c05336c4>] (phy_led_triggers_unregister) from [<c0531d44>] (phy_detach+0x30/0x74)
[<c0531d44>] (phy_detach) from [<c0538bdc>] (sh_eth_close+0x64/0x9c)
[<c0538bdc>] (sh_eth_close) from [<c04d4ce0>] (dpm_run_callback+0x48/0xc8)
or:
list_del corruption. prev->next should be dede6540, but was 2e323931
------------[ cut here ]------------
kernel BUG at lib/list_debug.c:52!
...
[<c02f6d70>] (__list_del_entry_valid) from [<c0425168>] (led_trigger_unregister+0x34/0xcc)
[<c0425168>] (led_trigger_unregister) from [<c03a05a0>] (phy_led_triggers_unregister+0x28/0x34)
[<c03a05a0>] (phy_led_triggers_unregister) from [<c039ec04>] (phy_detach+0x30/0x74)
[<c039ec04>] (phy_detach) from [<c03a4fc0>] (sh_eth_close+0x6c/0xa4)
[<c03a4fc0>] (sh_eth_close) from [<c0483234>] (__dev_close_many+0xac/0xd0)
To fix this, clear phy_device.phy_num_led_triggers in the error path of
phy_led_triggers_register() fails.
Note that the "No phy led trigger registered for speed" message will
still be printed on link speed changes, which is a good cue that
something went wrong with the LED triggers.
Fixes: 2e0bc452f4721520 ("net: phy: leds: add support for led triggers on phy link state change")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the binding was defined, I was not aware that mt2701 was an earlier
version of the SoC. For sake of consistency, the ethernet driver should
use mt2701 inside the compat string as this is the earliest SoC with the
ethernet core.
The ethernet driver is currently of no real use until we finish and
upstream the DSA driver. There are no users of this binding yet. It should
be safe to fix this now before it is too late and we need to provide
backward compatibility for the mt7623-eth compat string.
Reported-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the binding was defined, I was not aware that mt2701 was an earlier
version of the SoC. For sake of consistency, the ethernet driver should
use mt2701 inside the compat string as this is the earliest SoC with the
ethernet core.
The ethernet driver is currently of no real use until we finish and
upstream the DSA driver. There are no users of this binding yet. It should
be safe to fix this now before it is too late and we need to provide
backward compatibility for the mt7623-eth compat string.
Reported-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: John Crispin <john@phrozen.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Michael Chan says:
====================
bnxt_en: Fix RTNL lock usage in bnxt_sp_task().
There are 2 function calls from bnxt_sp_task() that have buggy RTNL
usage. These 2 functions take RTNL lock under some conditions, but
some callers (such as open, ethtool) have already taken RTNL. These
3 patches fix the issue by making it clear that callers must take
RTNL. If the caller is bnxt_sp_task() which does not automatically
take RTNL, we add a common scheme for bnxt_sp_task() to call these
functions properly under RTNL.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
bnxt_get_port_module_status() calls bnxt_update_link() which expects
RTNL to be held. In bnxt_sp_task() that does not hold RTNL, we need to
call it with a prior call to bnxt_rtnl_lock_sp() and the call needs to
be moved to the end of bnxt_sp_task().
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
bnxt_update_link() is called from multiple code paths. Most callers,
such as open, ethtool, already hold RTNL. Only the caller bnxt_sp_task()
does not. So it is a bug to take RTNL inside bnxt_update_link().
Fix it by removing the RTNL inside bnxt_update_link(). The function
now expects the caller to always hold RTNL.
In bnxt_sp_task(), call bnxt_rtnl_lock_sp() before calling
bnxt_update_link(). We also need to move the call to the end of
bnxt_sp_task() since it will be clearing the BNXT_STATE_IN_SP_TASK bit.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In bnxt_sp_task(), we set a bit BNXT_STATE_IN_SP_TASK so that bnxt_close()
will synchronize and wait for bnxt_sp_task() to finish. Some functions
in bnxt_sp_task() require us to clear BNXT_STATE_IN_SP_TASK and then
acquire rtnl_lock() to prevent race conditions.
There are some bugs related to this logic. This patch refactors the code
to have common bnxt_rtnl_lock_sp() and bnxt_rtnl_unlock_sp() to handle
the RTNL and the clearing/setting of the bit. Multiple functions will
need the same logic. We also need to move bnxt_reset() to the end of
bnxt_sp_task(). Functions that clear BNXT_STATE_IN_SP_TASK must be the
last functions to be called in bnxt_sp_task(). The common scheme will
handle the condition properly.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull virtio/vhost fixes from Michael Tsirkin:
- ARM DMA fixes
- vhost vsock bugfix
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vring: Force use of DMA API for ARM-based systems with legacy devices
virtio_mmio: Set DMA masks appropriately
vhost/vsock: handle vhost_vq_init_access() error
|
|
sock_reset_flag() maps to __clear_bit() not the atomic version clear_bit().
Thus, we need smp_mb(), smp_mb__after_atomic() is not sufficient.
Fixes: 3c7151275c0c ("tcp: add memory barriers to write space paths")
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Jason Baron <jbaron@akamai.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Reported-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now sctp gso puts segments into skb's frag_list, then processes these
segments in skb_segment. But skb_segment handles them only when gs is
enabled, as it's in the same branch with skb's frags.
Although almost all the NICs support sg other than some old ones, but
since commit 1e16aa3ddf86 ("net: gso: use feature flag argument in all
protocol gso handlers"), features &= skb->dev->hw_enc_features, and
xfrm_output_gso call skb_segment with features = 0, which means sctp
gso would call skb_segment with sg = 0, and skb_segment would not work
as expected.
This patch is to fix it by setting features param with NETIF_F_SG when
calling skb_segment so that it can go the right branch to process the
skb's frag_list.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sctp_addr_id2transport is a function for sockopt to look up assoc by
address. As the address is from userspace, it can be a v4-mapped v6
address. But in sctp protocol stack, it always handles a v4-mapped
v6 address as a v4 address. So it's necessary to convert it to a v4
address before looking up assoc by address.
This patch is to fix it by calling sctp_verify_addr in which it can do
this conversion before calling sctp_endpoint_lookup_assoc, just like
what sctp_sendmsg and __sctp_connect do for the address from users.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With COW files they are the hotpath, just like for files with the
extent size hint attribute. We really shouldn't micro-manage anything
but failure cases with unlikely.
Additionally Arnd Bergmann recently reported that one of these two
unlikely annotations causes link failures together with an upcoming
kernel instrumentation patch, so let's get rid of it ASAP.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
|
|
xfs_attr_[get|remove]() have unlocked attribute fork checks to optimize
away a lock cycle in cases where the fork does not exist or is otherwise
empty. This check is not safe, however, because an attribute fork short
form to extent format conversion includes a transient state that causes
the xfs_inode_hasattr() check to fail. Specifically,
xfs_attr_shortform_to_leaf() creates an empty extent format attribute
fork and then adds the existing shortform attributes to it.
This means that lookup of an existing xattr can spuriously return
-ENOATTR when racing against a setxattr that causes the associated
format conversion. This was originally reproduced by an untar on a
particularly configured glusterfs volume, but can also be reproduced on
demand with properly crafted xattr requests.
The format conversion occurs under the exclusive ilock. xfs_attr_get()
and xfs_attr_remove() already have the proper locking and checks further
down in the functions to handle this situation correctly. Drop the
unlocked checks to avoid the spurious failure and rely on the existing
logic.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
|
|
Currently we try to rely on the global reserved block pool for block
allocations for the free inode btree, but I have customer reports
(fairly complex workload, need to find an easier reproducer) where that
is not enough as the AG where we free an inode that requires a new
finobt block is entirely full. This causes us to cancel a dirty
transaction and thus a file system shutdown.
I think the right way to guard against this is to treat the finot the same
way as the refcount btree and have a per-AG reservations for the possible
worst case size of it, and the patch below implements that.
Note that this could increase mount times with large finobt trees. In
an ideal world we would have added a field for the number of finobt
fields to the AGI, similar to what we did for the refcount blocks.
We should do add it next time we rev the AGI or AGF format by adding
new fields.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
|
|
Try to reserve the blocks first and only then update the fields in
or hanging off the mount structure. This way we can call __xfs_ag_resv_init
again after a previous failure.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
|
|
Revert commit 6276e53fa8c0 (ACPI / video: Add force_native quirk for
HP Pavilion dv6).
In the commit message for the quirk this revert removes I wrote:
"Note that there are quite a few HP Pavilion dv6 variants, some
woth ATI and some with NVIDIA hybrid gfx, both seem to need this
quirk to have working backlight control. There are also some versions
with only Intel integrated gfx, these may not need this quirk, but it
should not hurt there."
Unfortunately that seems wrong, I've already received 2 reports of
this commit causing regressions on some dv6 variants (at least one
of which actually has a nvidia GPU). So it seems that HP has made a
mess here by using the same model-name both in marketing and in the
DMI data for many different variants. Some of which need
acpi_backlight=native for functional backlight control (as the
quirk this commit reverts was doing), where as others are broken by
it. So lets get back to the old sitation so as to avoid regressing
on models which used to work without any kernel cmdline arguments
before.
Fixes: 6276e53fa8c0 (ACPI / video: Add force_native quirk for HP Pavilion dv6)
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
drm-intel-fixes
gvt-fixes-2017-01-25
- re-enable shadow batch buffer for security that was falsely turned off.
- kvmgt/mdev typo fix for correct ABI
- gvt mail list change
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
The call went away in:
commit 3b16525cc4c1a43e9053cfdc414356eea24bdfad
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Thu Aug 4 16:32:25 2016 +0100
drm/i915: Split insertion/binding of an object into the VM
It is useful to have this trace as it pairs nicely with the vma_unbind
one to track vma activity.
Added inside the i915_vma_bind function (was outside before) to keep a
similar placement as trace_i915_vma_unbind.
v2: print bind_flags instead of flags (Chris)
Fixes: 3b16525cc4c1 ("drm/i915: Split insertion/binding of an object into the VM")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1484949083-11430-1-git-send-email-daniele.ceraolospurio@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit 6146e6da5c961735dacf9b6c0c8b5f1382193ee2)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Fences are required to support being released from under an atomic context.
The drm_atomic_state struct may take a mutex when being released and so
we cannot drop a reference to the drm_atomic_state from the fence release
path directly, and so we need to defer that unreference to a worker.
[ 326.576697] WARNING: CPU: 2 PID: 366 at kernel/sched/core.c:7737 __might_sleep+0x5d/0x80
[ 326.576816] do not call blocking ops when !TASK_RUNNING; state=1 set at [<ffffffffc0359549>] intel_breadcrumbs_signaler+0x59/0x270 [i915]
[ 326.576818] Modules linked in: rfcomm fuse snd_hda_codec_hdmi bnep snd_hda_codec_realtek snd_hda_codec_generic snd_hda_intel snd_hda_codec snd_hwdep snd_hda_core snd_pcm snd_seq_midi snd_seq_midi_event snd_rawmidi snd_seq snd_seq_device snd_timer input_leds led_class snd punit_atom_debug btusb btrtl btbcm btintel intel_rapl bluetooth i915 drm_kms_helper syscopyarea sysfillrect iwlwifi sysimgblt soundcore fb_sys_fops mei_txe cfg80211 drm pwm_lpss_platform pwm_lpss pinctrl_cherryview fjes acpi_pad parport_pc ppdev parport autofs4
[ 326.576899] CPU: 2 PID: 366 Comm: i915/signal:0 Tainted: G U 4.10.0-rc3-patser+ #5030
[ 326.576902] Hardware name: /NUC5PPYB, BIOS PYBSWCEL.86A.0031.2015.0601.1712 06/01/2015
[ 326.576905] Call Trace:
[ 326.576920] dump_stack+0x4d/0x6d
[ 326.576926] __warn+0xc0/0xe0
[ 326.576931] warn_slowpath_fmt+0x5a/0x80
[ 326.577004] ? intel_breadcrumbs_signaler+0x59/0x270 [i915]
[ 326.577075] ? intel_breadcrumbs_signaler+0x59/0x270 [i915]
[ 326.577079] __might_sleep+0x5d/0x80
[ 326.577087] mutex_lock+0x1b/0x40
[ 326.577133] drm_property_free_blob+0x1e/0x80 [drm]
[ 326.577167] ? drm_property_destroy+0xe0/0xe0 [drm]
[ 326.577200] drm_mode_object_unreference+0x5c/0x70 [drm]
[ 326.577233] drm_property_unreference_blob+0xe/0x10 [drm]
[ 326.577260] __drm_atomic_helper_crtc_destroy_state+0x14/0x40 [drm_kms_helper]
[ 326.577278] drm_atomic_helper_crtc_destroy_state+0x10/0x20 [drm_kms_helper]
[ 326.577352] intel_crtc_destroy_state+0x9/0x10 [i915]
[ 326.577388] drm_atomic_state_default_clear+0xea/0x1d0 [drm]
[ 326.577462] intel_atomic_state_clear+0xd/0x20 [i915]
[ 326.577497] drm_atomic_state_clear+0x1a/0x30 [drm]
[ 326.577532] __drm_atomic_state_free+0x13/0x60 [drm]
[ 326.577607] intel_atomic_commit_ready+0x6f/0x78 [i915]
[ 326.577670] i915_sw_fence_release+0x3a/0x50 [i915]
[ 326.577733] dma_i915_sw_fence_wake+0x39/0x80 [i915]
[ 326.577741] dma_fence_signal+0xda/0x120
[ 326.577812] ? intel_breadcrumbs_signaler+0x59/0x270 [i915]
[ 326.577884] intel_breadcrumbs_signaler+0xb1/0x270 [i915]
[ 326.577889] kthread+0x127/0x130
[ 326.577961] ? intel_engine_remove_wait+0x1a0/0x1a0 [i915]
[ 326.577964] ? kthread_stop+0x120/0x120
[ 326.577970] ret_from_fork+0x22/0x30
Fixes: c004a90b7263 ("drm/i915: Restore nonblocking awaits for modesetting")
Reported-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170123212939.30345-1-chris@chris-wilson.co.uk
Cc: <drm-intel-fixes@lists.freedesktop.org> # v4.10-rc1+
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
(cherry picked from commit eb955eee27d9dc176871540c43c9070ee4701642)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
In intel_crtc_disable_noatomic(), bail on a failure to allocate an
atomic state to avoid a NULL pointer dereference.
Fixes: 4a80655827af ("drm/i915: Pass atomic state to crtc enable/disable functions")
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: intel-gfx@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v4.9+
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1484922525-6131-4-git-send-email-ander.conselvan.de.oliveira@intel.com
(cherry picked from commit 31bb2ef97ea9db343348f9b5ccaa9bb6f48fc655)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Parameters tile_size, tile_width and tile_height were passed in the
wrong order to _intel_adjust_tile_offset() when calculating the rotated
offsets.
This doesn't fix any user visible bug, since for packed formats new
and old offset are the same and the rotated offsets are within a tile
before they are fed to _intel_adjust_tile_offset(). In that case, the
offsets are unchanged. That is not true for planar formats, but those
are currently not supported.
Fixes: 66a2d927cb0e ("drm/i915: Make intel_adjust_tile_offset() work for linear buffers")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: intel-gfx@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v4.9+
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1484922525-6131-3-git-send-email-ander.conselvan.de.oliveira@intel.com
(cherry picked from commit 46a1bd289507dfcc428fb9daf65421ed6be6af8b)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
