| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fix from Ingo Molnar:
"Fix a timer granularity handling race+bug, which would manifest itself
by spuriously increasing timeouts of some timers (from 1 jiffy to ~500
jiffies in the worst case measured) in certain nohz states"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timers: Fix excessive granularity of new timers after a nohz idle
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fix from Ingo Molnar:
"A single fix to not allow nonsensical event groups that result in
kernel warnings"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/core: Fix group {cpu,task} validation
|
|
In comqit fc6eead7c1e2 ("time: Clean up CLOCK_MONOTONIC_RAW time
handling"), the following code got mistakenly added to the update of the
raw timekeeper:
/* Update the monotonic raw base */
seconds = tk->raw_sec;
nsec = (u32)(tk->tkr_raw.xtime_nsec >> tk->tkr_raw.shift);
tk->tkr_raw.base = ns_to_ktime(seconds * NSEC_PER_SEC + nsec);
Which adds the raw_sec value and the shifted down raw xtime_nsec to the
base value.
But the read function adds the shifted down tk->tkr_raw.xtime_nsec value
another time, The result of this is that ktime_get_raw() users (which are
all internal users) see the raw time move faster then it should (the rate
at which can vary with the current size of tkr_raw.xtime_nsec), which has
resulted in at least problems with graphics rendering performance.
The change tried to match the monotonic base update logic:
seconds = (u64)(tk->xtime_sec + tk->wall_to_monotonic.tv_sec);
nsec = (u32) tk->wall_to_monotonic.tv_nsec;
tk->tkr_mono.base = ns_to_ktime(seconds * NSEC_PER_SEC + nsec);
Which adds the wall_to_monotonic.tv_nsec value, but not the
tk->tkr_mono.xtime_nsec value to the base.
To fix this, simplify the tkr_raw.base accumulation to only accumulate the
raw_sec portion, and do not include the tkr_raw.xtime_nsec portion, which
will be added at read time.
Fixes: fc6eead7c1e2 ("time: Clean up CLOCK_MONOTONIC_RAW time handling")
Reported-and-tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Kevin Brodsky <kevin.brodsky@arm.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Stephen Boyd <stephen.boyd@linaro.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Miroslav Lichvar <mlichvar@redhat.com>
Cc: Daniel Mentz <danielmentz@google.com>
Link: http://lkml.kernel.org/r/1503701824-1645-1-git-send-email-john.stultz@linaro.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.13
Only one iwlwifi patch this time.
iwlwifi
* fix multiple times reported lockdep warning found by new locking
annotation introduced in v4.13-rc1
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, in the udp6 code, the dst cookie is not initialized/updated
concurrently with the RX dst used by early demux.
As a result, the dst_check() in the early_demux path always fails,
the rx dst cache is always invalidated, and we can't really
leverage significant gain from the demux lookup.
Fix it adding udp6 specific variant of sk_rx_dst_set() and use it
to set the dst cookie when the dst entry is really changed.
The issue is there since the introduction of early demux for ipv6.
Fixes: 5425077d73e0 ("net: ipv6: Add early demux handler for UDP unicast")
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Check memory allocation failure and return -ENOMEM in such a case, as
already done few lines below for another memory allocation.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Florian Fainelli says:
====================
r8169: Be drop monitor friendly
First patch may be questionable but no other driver appears to be
doing that and while it is defendable to account for left packets as
dropped during TX clean, this appears misleading. I picked Stanislaw
changes which brings us back to 2010, but this was present from
pre-git days as well.
Second patch fixes the two missing calls to dev_consume_skb_any().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
rtl_tx() is the TX reclamation process whereas rtl8169_tx_clear_range() does
the TX ring cleaning during shutdown, both of these functions should call
dev_consume_skb_any() to be drop monitor friendly.
Fixes: cac4b22f3d6a ("r8169: do not account fragments as packets")
Fixes: eb781397904e ("r8169: Do not use dev_kfree_skb in xmit path")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
rtl8169_tx_clear_range() is responsible for cleaning up the TX ring
during interface shutdown, incrementing tx_dropped for every SKB that we
left at the time in the ring is misleading.
Fixes: cac4b22f3d6a ("r8169: do not account fragments as packets")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Merge misc fixes from Andrew Morton:
"6 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm/memblock.c: reversed logic in memblock_discard()
fork: fix incorrect fput of ->exe_file causing use-after-free
mm/madvise.c: fix freeing of locked page with MADV_FREE
dax: fix deadlock due to misaligned PMD faults
mm, shmem: fix handling /sys/kernel/mm/transparent_hugepage/shmem_enabled
PM/hibernate: touch NMI watchdog when creating snapshot
|
|
Pull Paolo Bonzini:
"Bugfixes for x86, PPC and s390"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: PPC: Book3S: Fix race and leak in kvm_vm_ioctl_create_spapr_tce()
KVM, pkeys: do not use PKRU value in vcpu->arch.guest_fpu.state
KVM: x86: simplify handling of PKRU
KVM: x86: block guest protection keys unless the host has them enabled
KVM: PPC: Book3S HV: Add missing barriers to XIVE code and document them
KVM: PPC: Book3S HV: Workaround POWER9 DD1.0 bug causing IPB bit loss
KVM: PPC: Book3S HV: Use msgsync with hypervisor doorbells on POWER9
KVM: s390: sthyi: fix specification exception detection
KVM: s390: sthyi: fix sthyi inline assembly
|
|
Pull virtio fixes from Michael Tsirkin:
"Fixes two obvious bugs in virtio pci"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio_pci: fix cpu affinity support
virtio_blk: fix incorrect message when disk is resized
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fix from Michael Ellerman:
"Just one fix, to add a barrier in the switch_mm() code to make sure
the mm cpumask update is ordered vs the MMU starting to load
translations. As far as we know no one's actually hit the bug, but
that's just luck.
Thanks to Benjamin Herrenschmidt, Nicholas Piggin"
* tag 'powerpc-4.13-8' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/mm: Ensure cpumask update is ordered
|
|
Pull nfsd fixes from Bruce Fields:
"Two nfsd bugfixes, neither 4.13 regressions, but both potentially
serious"
* tag 'nfsd-4.13-2' of git://linux-nfs.org/~bfields/linux:
net: sunrpc: svcsock: fix NULL-pointer exception
nfsd: Limit end of page list when decoding NFSv4 WRITE
|
|
git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"Some bug fixes for stable for cifs"
* tag 'cifs-fixes-for-4.13-rc6-and-stable' of git://git.samba.org/sfrench/cifs-2.6:
cifs: return ENAMETOOLONG for overlong names in cifs_open()/cifs_lookup()
cifs: Fix df output for users with quota limits
|
|
There are a few bugs around refcnt handling in the new BPF congestion
control setsockopt:
- The new ca is assigned to icsk->icsk_ca_ops even in the case where we
cannot get a reference on it. This would lead to a use after free,
since that ca is going away soon.
- Changing the congestion control case doesn't release the refcnt on
the previous ca.
- In the reinit case, we first leak a reference on the old ca, then we
call tcp_reinit_congestion_control on the ca that we have just
assigned, leading to deinitializing the wrong ca (->release of the
new ca on the old ca's data) and releasing the refcount on the ca
that we actually want to use.
This is visible by building (for example) BIC as a module and setting
net.ipv4.tcp_congestion_control=bic, and using tcp_cong_kern.c from
samples/bpf.
This patch fixes the refcount issues, and moves reinit back into tcp
core to avoid passing a ca pointer back to BPF.
Fixes: 91b5b21c7c16 ("bpf: Add support for changing congestion control")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Lawrence Brakmo <brakmo@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull MTD fixes from Brian Norris:
"Two fixes - one for a 4.13 regression, and the other for an older one:
- Atmel NAND: since we started utilizing ONFI timings, we found that
we were being too restrict at rejecting them, partly due to
discrepancies in ONFI 4.0 and earlier versions. Relax the
restriction to keep these platforms booting. This is a 4.13-rc1
regression.
- nandsim: repeated probe/removal may not work after a failed init,
because we didn't free up our debugfs files properly on the failure
path. This has been around since 3.8, but it's nice to get this
fixed now in a nice easy patch that can target -stable, since
there's already refactoring work (that also fixes the issue)
targeted for the next merge window"
* tag 'for-linus-20170825' of git://git.infradead.org/linux-mtd:
mtd: nand: atmel: Relax tADL_min constraint
mtd: nandsim: remove debugfs entries in error path
|
|
rt_cookie might be used uninitialized, fix this by
initializing it.
Fixes: c5cff8561d2d ("ipv6: add rcu grace period before freeing fib6_node")
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull block fixes from Jens Axboe:
"A small batch of fixes that should be included for the 4.13 release.
This contains:
- Revert of the 4k loop blocksize support. Even with a recent batch
of 4 fixes, we're still not really happy with it. Rather than be
stuck with an API issue, let's revert it and get it right for 4.14.
- Trivial patch from Bart, adding a few flags to the blk-mq debugfs
exports that were added in this release, but not to the debugfs
parts.
- Regression fix for bsg, fixing a potential kernel panic. From
Benjamin.
- Tweak for the blk throttling, improving how we account discards.
From Shaohua"
* 'for-linus' of git://git.kernel.dk/linux-block:
blk-mq-debugfs: Add names for recently added flags
bsg-lib: fix kernel panic resulting from missing allocation of reply-buffer
Revert "loop: support 4k physical blocksize"
blk-throttle: cap discard request size
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"I2C has some bugfixes for you: mainly Jarkko fixed up a few things in
the designware driver regarding the new slave mode. But Ulf also fixed
a long-standing and now agreed suspend problem. Plus, some simple
stuff which nonetheless needs fixing"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: designware: Fix runtime PM for I2C slave mode
i2c: designware: Remove needless pm_runtime_put_noidle() call
i2c: aspeed: fixed potential null pointer dereference
i2c: simtec: use release_mem_region instead of release_resource
i2c: core: Make comment about I2C table requirement to reflect the code
i2c: designware: Fix standard mode speed when configuring the slave mode
i2c: designware: Fix oops from i2c_dw_irq_handler_slave
i2c: designware: Fix system suspend
|
|
irq_create_affinity_masks() can return NULL on non-SMP systems, when there
are not enough "free" vectors available to spread, or if memory allocation
for the CPU masks fails. Only the allocation failure is of interest, and
even then the system will work just fine except for non-optimally spread
vectors. Thus remove the warnings.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fix from Ulf Hansson:
"MMC core: don't return error code R1_OUT_OF_RANGE for open-ending mode"
* tag 'mmc-v4.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: block: prevent propagating R1_OUT_OF_RANGE for open-ending mode
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"We're keeping in a good shape, this batch contains just a few small
fixes (a regression fix for ASoC rt5677 codec, NULL dereference and
error-path fixes in firewire, and a corner-case ioctl error fix for
user TLV), as well as usual quirks for USB-audio and HD-audio"
* tag 'sound-4.13-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ASoC: rt5677: Reintroduce I2C device IDs
ALSA: hda - Add stereo mic quirk for Lenovo G50-70 (17aa:3978)
ALSA: core: Fix unexpected error at replacing user TLV
ALSA: usb-audio: Add delay quirk for H650e/Jabra 550a USB headsets
ALSA: firewire-motu: destroy stream data surely at failure of card initialization
ALSA: firewire: fix NULL pointer dereference when releasing uninitialized data of iso-resource
|
|
git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine fix from Vinod Koul:
"A single fix for tegra210-adma driver to check of_irq_get() error"
* tag 'dmaengine-fix-4.13-rc7' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: tegra210-adma: fix of_irq_get() error check
|
|
git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Fixes for rc7, nothing too crazy, some core, i915, and sunxi fixes,
Intel CI has been responsible for some of these fixes being required"
* tag 'drm-fixes-for-v4.13-rc7' of git://people.freedesktop.org/~airlied/linux:
drm/i915/gvt: Fix the kernel null pointer error
drm: Release driver tracking before making the object available again
drm/i915: Clear lost context-switch interrupts across reset
drm/i915/bxt: use NULL for GPIO connection ID
drm/i915/cnl: Fix LSPCON support.
drm/i915/vbt: ignore extraneous child devices for a port
drm/i915: Initialize 'data' in intel_dsi_dcs_backlight.c
drm/atomic: If the atomic check fails, return its value first
drm/atomic: Handle -EDEADLK with out-fences correctly
drm: Fix framebuffer leak
drm/imx: ipuv3-plane: fix YUV framebuffer scanout on the base plane
gpu: ipu-v3: add DRM dependency
drm/rockchip: Fix suspend crash when drm is not bound
drm/sun4i: Implement drm_driver lastclose to restore fbdev console
|
|
In recently introduced memblock_discard() there is a reversed logic bug.
Memory is freed of static array instead of dynamically allocated one.
Link: http://lkml.kernel.org/r/1503511441-95478-2-git-send-email-pasha.tatashin@oracle.com
Fixes: 3010f876500f ("mm: discard memblock data later")
Signed-off-by: Pavel Tatashin <pasha.tatashin@oracle.com>
Reported-by: Woody Suwalski <terraluna977@gmail.com>
Tested-by: Woody Suwalski <terraluna977@gmail.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 7c051267931a ("mm, fork: make dup_mmap wait for mmap_sem for
write killable") made it possible to kill a forking task while it is
waiting to acquire its ->mmap_sem for write, in dup_mmap().
However, it was overlooked that this introduced an new error path before
a reference is taken on the mm_struct's ->exe_file. Since the
->exe_file of the new mm_struct was already set to the old ->exe_file by
the memcpy() in dup_mm(), it was possible for the mmput() in the error
path of dup_mm() to drop a reference to ->exe_file which was never
taken.
This caused the struct file to later be freed prematurely.
Fix it by updating mm_init() to NULL out the ->exe_file, in the same
place it clears other things like the list of mmaps.
This bug was found by syzkaller. It can be reproduced using the
following C program:
#define _GNU_SOURCE
#include <pthread.h>
#include <stdlib.h>
#include <sys/mman.h>
#include <sys/syscall.h>
#include <sys/wait.h>
#include <unistd.h>
static void *mmap_thread(void *_arg)
{
for (;;) {
mmap(NULL, 0x1000000, PROT_READ,
MAP_POPULATE|MAP_ANONYMOUS|MAP_PRIVATE, -1, 0);
}
}
static void *fork_thread(void *_arg)
{
usleep(rand() % 10000);
fork();
}
int main(void)
{
fork();
fork();
fork();
for (;;) {
if (fork() == 0) {
pthread_t t;
pthread_create(&t, NULL, mmap_thread, NULL);
pthread_create(&t, NULL, fork_thread, NULL);
usleep(rand() % 10000);
syscall(__NR_exit_group, 0);
}
wait(NULL);
}
}
No special kernel config options are needed. It usually causes a NULL
pointer dereference in __remove_shared_vm_struct() during exit, or in
dup_mmap() (which is usually inlined into copy_process()) during fork.
Both are due to a vm_area_struct's ->vm_file being used after it's
already been freed.
Google Bug Id: 64772007
Link: http://lkml.kernel.org/r/20170823211408.31198-1-ebiggers3@gmail.com
Fixes: 7c051267931a ("mm, fork: make dup_mmap wait for mmap_sem for write killable")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Konstantin Khlebnikov <koct9i@gmail.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: <stable@vger.kernel.org> [v4.7+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
If madvise(..., MADV_FREE) split a transparent hugepage, it called
put_page() before unlock_page().
This was wrong because put_page() can free the page, e.g. if a
concurrent madvise(..., MADV_DONTNEED) has removed it from the memory
mapping. put_page() then rightfully complained about freeing a locked
page.
Fix this by moving the unlock_page() before put_page().
This bug was found by syzkaller, which encountered the following splat:
BUG: Bad page state in process syzkaller412798 pfn:1bd800
page:ffffea0006f60000 count:0 mapcount:0 mapping: (null) index:0x20a00
flags: 0x200000000040019(locked|uptodate|dirty|swapbacked)
raw: 0200000000040019 0000000000000000 0000000000020a00 00000000ffffffff
raw: ffffea0006f60020 ffffea0006f60020 0000000000000000 0000000000000000
page dumped because: PAGE_FLAGS_CHECK_AT_FREE flag(s) set
bad because of flags: 0x1(locked)
Modules linked in:
CPU: 1 PID: 3037 Comm: syzkaller412798 Not tainted 4.13.0-rc5+ #35
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:16 [inline]
dump_stack+0x194/0x257 lib/dump_stack.c:52
bad_page+0x230/0x2b0 mm/page_alloc.c:565
free_pages_check_bad+0x1f0/0x2e0 mm/page_alloc.c:943
free_pages_check mm/page_alloc.c:952 [inline]
free_pages_prepare mm/page_alloc.c:1043 [inline]
free_pcp_prepare mm/page_alloc.c:1068 [inline]
free_hot_cold_page+0x8cf/0x12b0 mm/page_alloc.c:2584
__put_single_page mm/swap.c:79 [inline]
__put_page+0xfb/0x160 mm/swap.c:113
put_page include/linux/mm.h:814 [inline]
madvise_free_pte_range+0x137a/0x1ec0 mm/madvise.c:371
walk_pmd_range mm/pagewalk.c:50 [inline]
walk_pud_range mm/pagewalk.c:108 [inline]
walk_p4d_range mm/pagewalk.c:134 [inline]
walk_pgd_range mm/pagewalk.c:160 [inline]
__walk_page_range+0xc3a/0x1450 mm/pagewalk.c:249
walk_page_range+0x200/0x470 mm/pagewalk.c:326
madvise_free_page_range.isra.9+0x17d/0x230 mm/madvise.c:444
madvise_free_single_vma+0x353/0x580 mm/madvise.c:471
madvise_dontneed_free mm/madvise.c:555 [inline]
madvise_vma mm/madvise.c:664 [inline]
SYSC_madvise mm/madvise.c:832 [inline]
SyS_madvise+0x7d3/0x13c0 mm/madvise.c:760
entry_SYSCALL_64_fastpath+0x1f/0xbe
Here is a C reproducer:
#define _GNU_SOURCE
#include <pthread.h>
#include <sys/mman.h>
#include <unistd.h>
#define MADV_FREE 8
#define PAGE_SIZE 4096
static void *mapping;
static const size_t mapping_size = 0x1000000;
static void *madvise_thrproc(void *arg)
{
madvise(mapping, mapping_size, (long)arg);
}
int main(void)
{
pthread_t t[2];
for (;;) {
mapping = mmap(NULL, mapping_size, PROT_WRITE,
MAP_POPULATE|MAP_ANONYMOUS|MAP_PRIVATE, -1, 0);
munmap(mapping + mapping_size / 2, PAGE_SIZE);
pthread_create(&t[0], 0, madvise_thrproc, (void*)MADV_DONTNEED);
pthread_create(&t[1], 0, madvise_thrproc, (void*)MADV_FREE);
pthread_join(t[0], NULL);
pthread_join(t[1], NULL);
munmap(mapping, mapping_size);
}
}
Note: to see the splat, CONFIG_TRANSPARENT_HUGEPAGE=y and
CONFIG_DEBUG_VM=y are needed.
Google Bug Id: 64696096
Link: http://lkml.kernel.org/r/20170823205235.132061-1-ebiggers3@gmail.com
Fixes: 854e9ed09ded ("mm: support madvise(MADV_FREE)")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: David Rientjes <rientjes@google.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: <stable@vger.kernel.org> [v4.5+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In DAX there are two separate places where the 2MiB range of a PMD is
defined.
The first is in the page tables, where a PMD mapping inserted for a
given address spans from (vmf->address & PMD_MASK) to ((vmf->address &
PMD_MASK) + PMD_SIZE - 1). That is, from the 2MiB boundary below the
address to the 2MiB boundary above the address.
So, for example, a fault at address 3MiB (0x30 0000) falls within the
PMD that ranges from 2MiB (0x20 0000) to 4MiB (0x40 0000).
The second PMD range is in the mapping->page_tree, where a given file
offset is covered by a radix tree entry that spans from one 2MiB aligned
file offset to another 2MiB aligned file offset.
So, for example, the file offset for 3MiB (pgoff 768) falls within the
PMD range for the order 9 radix tree entry that ranges from 2MiB (pgoff
512) to 4MiB (pgoff 1024).
This system works so long as the addresses and file offsets for a given
mapping both have the same offsets relative to the start of each PMD.
Consider the case where the starting address for a given file isn't 2MiB
aligned - say our faulting address is 3 MiB (0x30 0000), but that
corresponds to the beginning of our file (pgoff 0). Now all the PMDs in
the mapping are misaligned so that the 2MiB range defined in the page
tables never matches up with the 2MiB range defined in the radix tree.
The current code notices this case for DAX faults to storage with the
following test in dax_pmd_insert_mapping():
if (pfn_t_to_pfn(pfn) & PG_PMD_COLOUR)
goto unlock_fallback;
This test makes sure that the pfn we get from the driver is 2MiB
aligned, and relies on the assumption that the 2MiB alignment of the pfn
we get back from the driver matches the 2MiB alignment of the faulting
address.
However, faults to holes were not checked and we could hit the problem
described above.
This was reported in response to the NVML nvml/src/test/pmempool_sync
TEST5:
$ cd nvml/src/test/pmempool_sync
$ make TEST5
You can grab NVML here:
https://github.com/pmem/nvml/
The dmesg warning you see when you hit this error is:
WARNING: CPU: 13 PID: 2900 at fs/dax.c:641 dax_insert_mapping_entry+0x2df/0x310
Where we notice in dax_insert_mapping_entry() that the radix tree entry
we are about to replace doesn't match the locked entry that we had
previously inserted into the tree. This happens because the initial
insertion was done in grab_mapping_entry() using a pgoff calculated from
the faulting address (vmf->address), and the replacement in
dax_pmd_load_hole() => dax_insert_mapping_entry() is done using
vmf->pgoff.
In our failure case those two page offsets (one calculated from
vmf->address, one using vmf->pgoff) point to different order 9 radix
tree entries.
This failure case can result in a deadlock because the radix tree unlock
also happens on the pgoff calculated from vmf->address. This means that
the locked radix tree entry that we swapped in to the tree in
dax_insert_mapping_entry() using vmf->pgoff is never unlocked, so all
future faults to that 2MiB range will block forever.
Fix this by validating that the faulting address's PMD offset matches
the PMD offset from the start of the file. This check is done at the
very beginning of the fault and covers faults that would have mapped to
storage as well as faults to holes. I left the COLOUR check in
dax_pmd_insert_mapping() in place in case we ever hit the insanity
condition where the alignment of the pfn we get from the driver doesn't
match the alignment of the userspace address.
Link: http://lkml.kernel.org/r/20170822222436.18926-1-ross.zwisler@linux.intel.com
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Reported-by: "Slusarz, Marcin" <marcin.slusarz@intel.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Matthew Wilcox <mawilcox@microsoft.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
/sys/kernel/mm/transparent_hugepage/shmem_enabled controls if we want
to allocate huge pages when allocate pages for private in-kernel shmem
mount.
Unfortunately, as Dan noticed, I've screwed it up and the only way to
make kernel allocate huge page for the mount is to use "force" there.
All other values will be effectively ignored.
Link: http://lkml.kernel.org/r/20170822144254.66431-1-kirill.shutemov@linux.intel.com
Fixes: 5a6e75f8110c ("shmem: prepare huge= mount option and sysfs knob")
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable <stable@vger.kernel.org> [4.8+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
There is a problem that when counting the pages for creating the
hibernation snapshot will take significant amount of time, especially on
system with large memory. Since the counting job is performed with irq
disabled, this might lead to NMI lockup. The following warning were
found on a system with 1.5TB DRAM:
Freezing user space processes ... (elapsed 0.002 seconds) done.
OOM killer disabled.
PM: Preallocating image memory...
NMI watchdog: Watchdog detected hard LOCKUP on cpu 27
CPU: 27 PID: 3128 Comm: systemd-sleep Not tainted 4.13.0-0.rc2.git0.1.fc27.x86_64 #1
task: ffff9f01971ac000 task.stack: ffffb1a3f325c000
RIP: 0010:memory_bm_find_bit+0xf4/0x100
Call Trace:
swsusp_set_page_free+0x2b/0x30
mark_free_pages+0x147/0x1c0
count_data_pages+0x41/0xa0
hibernate_preallocate_memory+0x80/0x450
hibernation_snapshot+0x58/0x410
hibernate+0x17c/0x310
state_store+0xdf/0xf0
kobj_attr_store+0xf/0x20
sysfs_kf_write+0x37/0x40
kernfs_fop_write+0x11c/0x1a0
__vfs_write+0x37/0x170
vfs_write+0xb1/0x1a0
SyS_write+0x55/0xc0
entry_SYSCALL_64_fastpath+0x1a/0xa5
...
done (allocated 6590003 pages)
PM: Allocated 26360012 kbytes in 19.89 seconds (1325.28 MB/s)
It has taken nearly 20 seconds(2.10GHz CPU) thus the NMI lockup was
triggered. In case the timeout of the NMI watch dog has been set to 1
second, a safe interval should be 6590003/20 = 320k pages in theory.
However there might also be some platforms running at a lower frequency,
so feed the watchdog every 100k pages.
[yu.c.chen@intel.com: simplification]
Link: http://lkml.kernel.org/r/1503460079-29721-1-git-send-email-yu.c.chen@intel.com
[yu.c.chen@intel.com: use interval of 128k instead of 100k to avoid modulus]
Link: http://lkml.kernel.org/r/1503328098-5120-1-git-send-email-yu.c.chen@intel.com
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Reported-by: Jan Filipcewicz <jan.filipcewicz@intel.com>
Suggested-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Michal Hocko <mhocko@suse.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Len Brown <lenb@kernel.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In xen_blkif_disconnect, before checking inflight I/O, following code
stops the blkback thread,
if (ring->xenblkd) {
kthread_stop(ring->xenblkd);
wake_up(&ring->shutdown_wq);
}
If there is inflight I/O in any non-last queue, blkback returns -EBUSY
directly, and above code would not be called to stop thread of remaining
queue and processs them. When removing vbd device with lots of disk I/O
load, some queues with inflight I/O still have blkback thread running even
though the corresponding vbd device or guest is gone.
And this could cause some problems, for example, if the backend device type
is file, some loop devices and blkback thread always lingers there forever
after guest is destroyed, and this causes failure of umounting repositories
unless rebooting the dom0.
This patch allows thread of every queue has the chance to get stopped.
Otherwise, only thread of queue previous to(including) first busy one get
stopped, blkthread of remaining queue will still run. So stop all threads
properly and return -EBUSY if any queue has inflight I/O.
Signed-off-by: Annie Li <annie.li@oracle.com>
Reviewed-by: Herbert van den Bergh <herbert.van.den.bergh@oracle.com>
Reviewed-by: Bhavesh Davda <bhavesh.davda@oracle.com>
Reviewed-by: Adnan Misherfi <adnan.misherfi@oracle.com>
Acked-by: Roger Pau Monné <roger.pau@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
Commit 0b0f9dc5 ("Revert "virtio_pci: use shared interrupts for
virtqueues"") removed the adjustment of the pre_vectors for the virtio
MSI-X vector allocation which was added in commit fb5e31d9 ("virtio:
allow drivers to request IRQ affinity when creating VQs"). This will
lead to an incorrect assignment of MSI-X vectors, and potential
deadlocks when offlining cpus.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Fixes: 0b0f9dc5 ("Revert "virtio_pci: use shared interrupts for virtqueues")
Reported-by: YASUAKI ISHIMATSU <yasu.isimatu@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
The message printed on disk resize is incorrect. The following is
printed when resizing to 2 GiB:
$ truncate -s 1G test.img
$ qemu -device virtio-blk-pci,logical_block_size=4096,...
(qemu) block_resize drive1 2G
virtio_blk virtio0: new size: 4194304 4096-byte logical blocks (17.2 GB/16.0 GiB)
The virtio_blk capacity config field is in 512-byte sector units
regardless of logical_block_size as per the VIRTIO specification.
Therefore the message should read:
virtio_blk virtio0: new size: 524288 4096-byte logical blocks (2.15 GB/2.0 GiB)
Note that this only affects the printed message. Thankfully the actual
block device has the correct size because the block layer expects
capacity in sectors.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
The symbolic constants QUEUE_FLAG_SCSI_PASSTHROUGH, QUEUE_FLAG_QUIESCED
and REQ_NOWAIT are missing from blk-mq-debugfs.c. Add these to
blk-mq-debugfs.c such that these appear as names in debugfs instead of
as numbers.
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Currently we unconditionally destroy all sysctl bits and regenerate
them after we've rebuild the domains (even if that rebuild is a
no-op).
And since we unconditionally (re)build the sysctl for all possible
CPUs, onlining all CPUs gets us O(n^2) time. Instead change this to
only rebuild the bits for CPUs we've actually installed new domains
on.
Reported-by: Ofer Levi(SW) <oferle@mellanox.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Fix partition_sched_domains() to try and preserve the existing machine
wide domain instead of unconditionally destroying it. We do this by
attempting to allocate the new single domain, only when that fails to
we reuse the fallback_doms.
When using fallback_doms we need to first destroy and then recreate
because both the old and new could be backed by it.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Ofer Levi(SW) <oferle@mellanox.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vineet.Gupta1@synopsys.com <Vineet.Gupta1@synopsys.com>
Cc: rusty@rustcorp.com.au <rusty@rustcorp.com.au>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
When disabling cpuset.sched_load_balance we expect to be able to online
CPUs without generating sched_domains. However this is currently
completely broken.
What happens is that we generate the sched_domains and then destroy
them. This is because of the spurious 'default' domain build in
cpuset_update_active_cpus(). That builds a single machine wide domain
and then schedules a work to build the 'real' domains. The work then
finds there are _no_ domains and destroys the lot again.
Furthermore, if there actually were cpusets, building the machine wide
domain is actively wrong, because it would allow tasks to 'escape' their
cpuset. Also I don't think its needed, the scheduler really should
respect the active mask.
Reported-by: Ofer Levi(SW) <oferle@mellanox.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vineet.Gupta1@synopsys.com <Vineet.Gupta1@synopsys.com>
Cc: rusty@rustcorp.com.au <rusty@rustcorp.com.au>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Mike provided a better comment for destroy_sched_domain() ...
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Found this issue by kmemleak: the 'sg' and 'sgc' pointers from
__sdt_alloc() might be leaked as each domain holds many groups' ref,
but in destroy_sched_domain(), it only declined the first group ref.
Onlining and offlining a CPU can trigger this leak, and cause OOM.
Reproducer for my 6 CPUs machine:
while true
do
echo 0 > /sys/devices/system/cpu/cpu5/online;
echo 1 > /sys/devices/system/cpu/cpu5/online;
done
unreferenced object 0xffff88007d772a80 (size 64):
comm "cpuhp/5", pid 39, jiffies 4294719962 (age 35.251s)
hex dump (first 32 bytes):
c0 22 77 7d 00 88 ff ff 02 00 00 00 01 00 00 00 ."w}............
40 2a 77 7d 00 88 ff ff 00 00 00 00 00 00 00 00 @*w}............
backtrace:
[<ffffffff8176525a>] kmemleak_alloc+0x4a/0xa0
[<ffffffff8121efe1>] __kmalloc_node+0xf1/0x280
[<ffffffff810d94a8>] build_sched_domains+0x1e8/0xf20
[<ffffffff810da674>] partition_sched_domains+0x304/0x360
[<ffffffff81139557>] cpuset_update_active_cpus+0x17/0x40
[<ffffffff810bdb2e>] sched_cpu_activate+0xae/0xc0
[<ffffffff810900e0>] cpuhp_invoke_callback+0x90/0x400
[<ffffffff81090597>] cpuhp_up_callbacks+0x37/0xb0
[<ffffffff81090887>] cpuhp_thread_fun+0xd7/0xf0
[<ffffffff810b37e0>] smpboot_thread_fn+0x110/0x160
[<ffffffff810af5d9>] kthread+0x109/0x140
[<ffffffff81770e45>] ret_from_fork+0x25/0x30
[<ffffffffffffffff>] 0xffffffffffffffff
unreferenced object 0xffff88007d772a40 (size 64):
comm "cpuhp/5", pid 39, jiffies 4294719962 (age 35.251s)
hex dump (first 32 bytes):
03 00 00 00 00 00 00 00 00 04 00 00 00 00 00 00 ................
00 04 00 00 00 00 00 00 4f 3c fc ff 00 00 00 00 ........O<......
backtrace:
[<ffffffff8176525a>] kmemleak_alloc+0x4a/0xa0
[<ffffffff8121efe1>] __kmalloc_node+0xf1/0x280
[<ffffffff810da16d>] build_sched_domains+0xead/0xf20
[<ffffffff810da674>] partition_sched_domains+0x304/0x360
[<ffffffff81139557>] cpuset_update_active_cpus+0x17/0x40
[<ffffffff810bdb2e>] sched_cpu_activate+0xae/0xc0
[<ffffffff810900e0>] cpuhp_invoke_callback+0x90/0x400
[<ffffffff81090597>] cpuhp_up_callbacks+0x37/0xb0
[<ffffffff81090887>] cpuhp_thread_fun+0xd7/0xf0
[<ffffffff810b37e0>] smpboot_thread_fn+0x110/0x160
[<ffffffff810af5d9>] kthread+0x109/0x140
[<ffffffff81770e45>] ret_from_fork+0x25/0x30
[<ffffffffffffffff>] 0xffffffffffffffff
Reported-by: Chunyu Hu <chuhu@redhat.com>
Signed-off-by: Shu Wang <shuwang@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Chunyu Hu <chuhu@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: liwang@redhat.com
Link: http://lkml.kernel.org/r/1502351536-9108-1-git-send-email-shuwang@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Nixiaoming pointed out that there is a memory leak in
kvm_vm_ioctl_create_spapr_tce() if the call to anon_inode_getfd()
fails; the memory allocated for the kvmppc_spapr_tce_table struct
is not freed, and nor are the pages allocated for the iommu
tables. In addition, we have already incremented the process's
count of locked memory pages, and this doesn't get restored on
error.
David Hildenbrand pointed out that there is a race in that the
function checks early on that there is not already an entry in the
stt->iommu_tables list with the same LIOBN, but an entry with the
same LIOBN could get added between then and when the new entry is
added to the list.
This fixes all three problems. To simplify things, we now call
anon_inode_getfd() before placing the new entry in the list. The
check for an existing entry is done while holding the kvm->lock
mutex, immediately before adding the new entry to the list.
Finally, on failure we now call kvmppc_account_memlimit to
decrement the process's count of locked memory pages.
Reported-by: Nixiaoming <nixiaoming@huawei.com>
Reported-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
All other fields use __
Cc: Ben Widawsky <ben@bwidawsk.net>
Fixes: db1689aa61b ("drm: Create a format/modifier blob")
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Signed-off-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170824150814.5878-1-lionel.g.landwerlin@intel.com
|
|
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
It can be difficult to figure out for user programs what features
the x86 CPU PMU driver actually supports. Currently it requires
grepping in dmesg, but dmesg is not always available.
This adds a caps directory to /sys/bus/event_source/devices/cpu/,
similar to the caps already used on intel_pt, which can be used to
discover the available capabilities cleanly.
Three capabilities are defined:
- pmu_name: Underlying CPU name known to the driver
- max_precise: Max precise level supported
- branches: Known depth of LBR.
Example:
% grep . /sys/bus/event_source/devices/cpu/caps/*
/sys/bus/event_source/devices/cpu/caps/branches:32
/sys/bus/event_source/devices/cpu/caps/max_precise:3
/sys/bus/event_source/devices/cpu/caps/pmu_name:skylake
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20170822185201.9261-3-andi@firstfloor.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Only show the Intel format attributes in sysfs when the feature is actually
supported with the current model numbers. This allows programs to probe
what format attributes are available, and give a sensible error message
to users if they are not.
This handles near all cases for intel attributes since Nehalem,
except the (obscure) case when the model number if known, but PEBS
is disabled in PERF_CAPABILITIES.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20170822185201.9261-2-andi@firstfloor.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
In an XDP redirect applications using tracepoint xdp:xdp_redirect to
diagnose TX overrun, I noticed perf_swevent_get_recursion_context()
was consuming 2% CPU. This was reduced to 1.85% with this simple
change.
Looking at the annotated asm code, it was clear that the unlikely case
in_nmi() test was chosen (by the compiler) as the most likely
event/branch. This small adjustment makes the compiler (GCC version
7.1.1 20170622 (Red Hat 7.1.1-3)) put in_nmi() as an unlikely branch.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/150342256382.16595.986861478681783732.stgit@firesoul
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The exiting/dead task has no PIDs and in this case perf_event_pid/tid()
return zero, change them to return -1 to distinguish this case from
idle threads.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho <acme@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20170822155928.GA6892@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Skylake changed the encoding of the PEBS data source field.
Some combinations are not available anymore, but some new cases
e.g. for L4 cache hit are added.
Fix up the conversion table for Skylake, similar as had been done
for Nehalem.
On Skylake server the encoding for L4 actually means persistent
memory. Handle this case too.
To properly describe it in the abstracted perf format I had to add
some new fields. Since a hit can have only one level add a new
field that is an enumeration, not a bit field to describe
the level. It can describe any level. Some numbers are also
used to describe PMEM and LFB.
Also add a new generic remote flag that can be combined with
the generic level to signify a remote cache.
And there is an extension field for the snoop indication to handle
the Forward state.
I didn't add a generic flag for hops because it's not needed
for Skylake.
I changed the existing encodings for older CPUs to also fill in the
new level and remote fields.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: acme@kernel.org
Cc: jolsa@kernel.org
Link: http://lkml.kernel.org/r/20170816222156.19953-3-andi@firstfloor.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Minor cleanup: use an explicit x86_pmu flag to handle the
missing Lock / TLB information on Nehalem, instead of always
checking the model number for each PEBS sample.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: acme@kernel.org
Cc: jolsa@kernel.org
Link: http://lkml.kernel.org/r/20170816222156.19953-2-andi@firstfloor.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The aux_watermark member of struct ring_buffer represents the period (in
terms of bytes) at which wakeup events should be generated when data is
written to the aux buffer in non-snapshot mode. On hardware that cannot
generate an interrupt when the aux_head reaches an arbitrary wakeup index
(such as ARM SPE), the aux_head sampled from handle->head in
perf_aux_output_{skip,end} may in fact be past the wakeup index. This
can lead to wakeup slowly falling behind the head. For example, consider
the case where hardware can only generate an interrupt on a page-boundary
and the aux buffer is initialised as follows:
// Buffer size is 2 * PAGE_SIZE
rb->aux_head = rb->aux_wakeup = 0
rb->aux_watermark = PAGE_SIZE / 2
following the first perf_aux_output_begin call, the handle is
initialised with:
handle->head = 0
handle->size = 2 * PAGE_SIZE
handle->wakeup = PAGE_SIZE / 2
and the hardware will be programmed to generate an interrupt at
PAGE_SIZE.
When the interrupt is raised, the hardware head will be at PAGE_SIZE,
so calling perf_aux_output_end(handle, PAGE_SIZE) puts the ring buffer
into the following state:
rb->aux_head = PAGE_SIZE
rb->aux_wakeup = PAGE_SIZE / 2
rb->aux_watermark = PAGE_SIZE / 2
and then the next call to perf_aux_output_begin will result in:
handle->head = handle->wakeup = PAGE_SIZE
for which the semantics are unclear and, for a smaller aux_watermark
(e.g. PAGE_SIZE / 4), then the wakeup would in fact be behind head at
this point.
This patch fixes the problem by rounding down the aux_head (as sampled
from the handle) to the nearest aux_watermark boundary when updating
rb->aux_wakeup, therefore taking into account any overruns by the
hardware.
Reported-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/1502900297-21839-2-git-send-email-will.deacon@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
