| Age | Commit message (Collapse) | Author |
|---|
|
Since 4.10, commit 8003c9ae204e (KVM: LAPIC: add APIC Timer
periodic/oneshot mode VMX preemption timer support), guests using
periodic LAPIC timers (such as FreeBSD 8.4) would see their timers
drift significantly over time.
Differences in the underlying clocks and numerical errors means the
periods of the two timers (hv and sw) are not the same. This
difference will accumulate with every expiry resulting in a large
error between the hv and sw timer.
This means the sw timer may be running slow when compared to the hv
timer. When the timer is switched from hv to sw, the now active sw
timer will expire late. The guest VCPU is reentered and it switches to
using the hv timer. This timer catches up, injecting multiple IRQs
into the guest (of which the guest only sees one as it does not get to
run until the hv timer has caught up) and thus the guest's timer rate
is low (and becomes increasing slower over time as the sw timer lags
further and further behind).
I believe a similar problem would occur if the hv timer is the slower
one, but I have not observed this.
Fix this by synchronizing the deadlines for both timers to the same
time source on every tick. This prevents the errors from accumulating.
Fixes: 8003c9ae204e21204e49816c5ea629357e283b06
Cc: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: David Vrabel <david.vrabel@nutanix.com>
Cc: stable@vger.kernel.org
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Wanpeng Li <wanpengli@tencent.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
Fixes for PPC KVM:
- Close a hole which could possibly lead to the host timebase getting
out of sync.
- Three fixes relating to PTEs and TLB entries for radix guests.
- Fix a bug which could lead to an interrupt never getting delivered
to the guest, if it is pending for a guest vCPU when the vCPU gets
offlined.
|
|
This one should be using the default LPM policy for mobile chipsets so
add the PCI ID to the driver list of supported revices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
|
|
Entry corresponding to 220 us setup time was missing. I am not aware of
any specific bug this fixes, but this could potentially result in enabling
PSR on a panel with a higher setup time requirement than supported by the
hardware.
I verified the value is present in eDP spec versions 1.3, 1.4 and 1.4a.
Fixes: 6608804b3d7f ("drm/dp: Add drm_dp_psr_setup_time()")
Cc: stable@vger.kernel.org
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jose Roberto de Souza <jose.souza@intel.com>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Tarun Vyas <tarun.vyas@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180511195145.3829-3-dhinakaran.pandiyan@intel.com
|
|
Use 64-bit accesses for 64-bit floating-point general registers with
PTRACE_PEEKUSR, removing the truncation of their upper halves in the
FR=1 mode, caused by commit bbd426f542cb ("MIPS: Simplify FP context
access"), which inadvertently switched them to using 32-bit accesses.
The PTRACE_POKEUSR side is fine as it's never been broken and continues
using 64-bit accesses.
Fixes: bbd426f542cb ("MIPS: Simplify FP context access")
Signed-off-by: Maciej W. Rozycki <macro@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 3.15+
Patchwork: https://patchwork.linux-mips.org/patch/19334/
Signed-off-by: James Hogan <jhogan@kernel.org>
|
|
Having PR_FP_MODE_FRE (i.e. Config5.FRE) set without PR_FP_MODE_FR (i.e.
Status.FR) is not supported as the lone purpose of Config5.FRE is to
emulate Status.FR=0 handling on FPU hardware that has Status.FR=1
hardwired[1][2]. Also we do not handle this case elsewhere, and assume
throughout our code that TIF_HYBRID_FPREGS and TIF_32BIT_FPREGS cannot
be set both at once for a task, leading to inconsistent behaviour if
this does happen.
Return unsuccessfully then from prctl(2) PR_SET_FP_MODE calls requesting
PR_FP_MODE_FRE to be set with PR_FP_MODE_FR clear. This corresponds to
modes allowed by `mips_set_personality_fp'.
References:
[1] "MIPS Architecture For Programmers, Vol. III: MIPS32 / microMIPS32
Privileged Resource Architecture", Imagination Technologies,
Document Number: MD00090, Revision 6.02, July 10, 2015, Table 9.69
"Config5 Register Field Descriptions", p. 262
[2] "MIPS Architecture For Programmers, Volume III: MIPS64 / microMIPS64
Privileged Resource Architecture", Imagination Technologies,
Document Number: MD00091, Revision 6.03, December 22, 2015, Table
9.72 "Config5 Register Field Descriptions", p. 288
Fixes: 9791554b45a2 ("MIPS,prctl: add PR_[GS]ET_FP_MODE prctl options for MIPS")
Signed-off-by: Maciej W. Rozycki <macro@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 4.0+
Patchwork: https://patchwork.linux-mips.org/patch/19327/
Signed-off-by: James Hogan <jhogan@kernel.org>
|
|
While doing a global software reset, these bits are not cleared and let
some bootloader fail to initialise the GPHYs. The bootloader don't
expect the GPHYs in reset, as they aren't during power on.
The asserts were a workaround for a wrong syscon-reboot mask. With a
mask set which includes the GPHY resets, these resets aren't required
any more.
Fixes: 126534141b45 ("MIPS: lantiq: Add a GPHY driver which uses the RCU syscon-mfd")
Signed-off-by: Mathias Kresin <dev@kresin.me>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: John Crispin <john@phrozen.org>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 4.14+
Patchwork: https://patchwork.linux-mips.org/patch/19003/
[jhogan@kernel.org: Fix build warnings]
Signed-off-by: James Hogan <jhogan@kernel.org>
|
|
Commit 15122ee2c515 ("arm64: Enforce BBM for huge IO/VMAP mappings")
disallowed block mappings for ioremap since that code does not honor
break-before-make. The same APIs are also used for permission updating
though and the extra checks prevent the permission updates from happening,
even though this should be permitted. This results in read-only permissions
not being fully applied. Visibly, this can occasionaly be seen as a failure
on the built in rodata test when the test data ends up in a section or
as an odd RW gap on the page table dump. Fix this by using
pgattr_change_is_safe instead of p*d_present for determining if the
change is permitted.
Reviewed-by: Kees Cook <keescook@chromium.org>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Fixes: 15122ee2c515 ("arm64: Enforce BBM for huge IO/VMAP mappings")
Signed-off-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Jun Wu at Facebook reported that an internal service was seeing a return
value of 1 from ftruncate() on Btrfs in some cases. This is coming from
the NEED_TRUNCATE_BLOCK return value from btrfs_truncate_inode_items().
btrfs_truncate() uses two variables for error handling, ret and err.
When btrfs_truncate_inode_items() returns non-zero, we set err to the
return value. However, NEED_TRUNCATE_BLOCK is not an error. Make sure we
only set err if ret is an error (i.e., negative).
To reproduce the issue: mount a filesystem with -o compress-force=zstd
and the following program will encounter return value of 1 from
ftruncate:
int main(void) {
char buf[256] = { 0 };
int ret;
int fd;
fd = open("test", O_CREAT | O_WRONLY | O_TRUNC, 0666);
if (fd == -1) {
perror("open");
return EXIT_FAILURE;
}
if (write(fd, buf, sizeof(buf)) != sizeof(buf)) {
perror("write");
close(fd);
return EXIT_FAILURE;
}
if (fsync(fd) == -1) {
perror("fsync");
close(fd);
return EXIT_FAILURE;
}
ret = ftruncate(fd, 128);
if (ret) {
printf("ftruncate() returned %d\n", ret);
close(fd);
return EXIT_FAILURE;
}
close(fd);
return EXIT_SUCCESS;
}
Fixes: ddfae63cc8e0 ("btrfs: move btrfs_truncate_block out of trans handle")
CC: stable@vger.kernel.org # 4.15+
Reported-by: Jun Wu <quark@fb.com>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
If io_destroy() gets to cancelling everything that can be cancelled and
gets to kiocb_cancel() calling the function driver has left in ->ki_cancel,
it becomes vulnerable to a race with IO completion. At that point req
is already taken off the list and aio_complete() does *NOT* spin until
we (in free_ioctx_users()) releases ->ctx_lock. As the result, it proceeds
to kiocb_free(), freing req just it gets passed to ->ki_cancel().
Fix is simple - remove from the list after the call of kiocb_cancel(). All
instances of ->ki_cancel() already have to cope with the being called with
iocb still on list - that's what happens in io_cancel(2).
Cc: stable@kernel.org
Fixes: 0460fef2a921 "aio: use cancellation list lazily"
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
This seems to be Synaptics specific, as some Elan touchpads are not
correctly switching to SMBus if we call deactivate before switching to
SMBus on cold boot and on resume.
Tested with the T480s
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: KT Liao <kt.liao@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
New ICs are using a different scheme for the alternate bus parameter.
Given that they are new and are only using either PS2 only or PS2 + SMBus
Host Notify, we force those new ICs to use the SMBus solution for enhanced
reporting.
This allows the touchpad found on the Lenovo T480s to report 5 fingers
every 8 ms, instead of having a limit of 2 every 8 ms.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: KT Liao <kt.liao@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Many of the Elantech devices are connected through PS/2 and a different
bus (SMBus or plain I2C).
To not break any existing device, we only enable SMBus based
on a module parameter. If some laptops require the quirk to
be set, we will have to rely on a list of PNPIds or MDI matching
to individually expose those hardware over SMBus.
the parameter mentioned above is elantech_smbus from the psmouse
module.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: KT Liao <kt.liao@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The command ETP_RESOLUTION_QUERY also contains the bus information.
It is better to fetch it once, while we are querying for device
information.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: KT Liao <kt.liao@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
In preparation for SMBus device support, move static device
information that we query form the touchpad upon initialization into
separate structure. This will allow us to query the device without
allocating memory first.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: KT Liao <kt.liao@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The Elan touchpads over I2C/SMBus also can handle a trackstick.
Unfortunately, nothing tells us if the device supports trackstick (the
information lies in the PS/2 node), so rely on device properties to
determine whether to enable the trackstick node.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1313939
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: KT Liao <kt.liao@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Recent patch forgot to remove nla_data(), upsetting syzkaller a bit.
BUG: KASAN: slab-out-of-bounds in nla_strlcpy+0x13d/0x150 lib/nlattr.c:314
Read of size 1 at addr ffff8801ad1f4fdd by task syz-executor189/4509
CPU: 1 PID: 4509 Comm: syz-executor189 Not tainted 4.17.0-rc6+ #62
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x1b9/0x294 lib/dump_stack.c:113
print_address_description+0x6c/0x20b mm/kasan/report.c:256
kasan_report_error mm/kasan/report.c:354 [inline]
kasan_report.cold.7+0x242/0x2fe mm/kasan/report.c:412
__asan_report_load1_noabort+0x14/0x20 mm/kasan/report.c:430
nla_strlcpy+0x13d/0x150 lib/nlattr.c:314
nfnl_acct_new+0x574/0xc50 net/netfilter/nfnetlink_acct.c:118
nfnetlink_rcv_msg+0xdb5/0xff0 net/netfilter/nfnetlink.c:212
netlink_rcv_skb+0x172/0x440 net/netlink/af_netlink.c:2448
nfnetlink_rcv+0x1fe/0x1ba0 net/netfilter/nfnetlink.c:513
netlink_unicast_kernel net/netlink/af_netlink.c:1310 [inline]
netlink_unicast+0x58b/0x740 net/netlink/af_netlink.c:1336
netlink_sendmsg+0x9f0/0xfa0 net/netlink/af_netlink.c:1901
sock_sendmsg_nosec net/socket.c:629 [inline]
sock_sendmsg+0xd5/0x120 net/socket.c:639
sock_write_iter+0x35a/0x5a0 net/socket.c:908
call_write_iter include/linux/fs.h:1784 [inline]
new_sync_write fs/read_write.c:474 [inline]
__vfs_write+0x64d/0x960 fs/read_write.c:487
vfs_write+0x1f8/0x560 fs/read_write.c:549
ksys_write+0xf9/0x250 fs/read_write.c:598
__do_sys_write fs/read_write.c:610 [inline]
__se_sys_write fs/read_write.c:607 [inline]
__x64_sys_write+0x73/0xb0 fs/read_write.c:607
Fixes: 4e09fc873d92 ("netfilter: prefer nla_strlcpy for dealing with NLA_STRING attributes")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Florian Westphal <fw@strlen.de>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
When posted work request, it need to compute the length of
all sges of every wr and fill it into the msg_len field of
send wqe. Thus, While posting multiple wr,
tmp_len should be reinitialized to zero.
Fixes: 8b9b8d143b46 ("RDMA/hns: Fix the endian problem for hns")
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
When use cq record db for kernel, it needs to set the hr_cq->db_en
to 1 and configure the dma address of record cq db of qp context.
Fixes: 86188a8810ed ("RDMA/hns: Support cq record doorbell for kernel space")
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
The err pointer comes from uverbs_attr_get, not from the uobject member,
which does not store an ERR_PTR.
Fixes: be934cca9e98 ("IB/uverbs: Add device memory registration ioctl support")
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
|
|
Each user_context receives a separate dpi value and thus a different
address on the doorbell bar. The qedr_mmap function needs to validate
the address and map the doorbell bar accordingly.
The current implementation always checked against dpi=0 doorbell range
leading to a wrong mapping for doorbell bar. (It entered an else case
that mapped the address differently). qedr_mmap should only be used
for doorbells, so the else was actually wrong in the first place.
This only has an affect on arm architecture and not an issue on a
x86 based architecture.
This lead to doorbells not occurring on arm based systems and left
applications that use more than one dpi (or several applications
run simultaneously ) to hang.
Fixes: ac1b36e55a51 ("qedr: Add support for user context verbs")
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
spin_lock/unlock was used instead of spin_un/lock_irq
in a procedure used in process space, on a spinlock
which can be grabbed in an interrupt.
This caused the stack trace below to be displayed (on kernel
4.17.0-rc1 compiled with Lock Debugging enabled):
[ 154.661474] WARNING: SOFTIRQ-safe -> SOFTIRQ-unsafe lock order detected
[ 154.668909] 4.17.0-rc1-rdma_rc_mlx+ #3 Tainted: G I
[ 154.675856] -----------------------------------------------------
[ 154.682706] modprobe/10159 [HC0[0]:SC0[0]:HE0:SE1] is trying to acquire:
[ 154.690254] 00000000f3b0e495 (&(&qp_table->lock)->rlock){+.+.}, at: mlx4_qp_remove+0x20/0x50 [mlx4_core]
[ 154.700927]
and this task is already holding:
[ 154.707461] 0000000094373b5d (&(&cq->lock)->rlock/1){....}, at: destroy_qp_common+0x111/0x560 [mlx4_ib]
[ 154.718028] which would create a new lock dependency:
[ 154.723705] (&(&cq->lock)->rlock/1){....} -> (&(&qp_table->lock)->rlock){+.+.}
[ 154.731922]
but this new dependency connects a SOFTIRQ-irq-safe lock:
[ 154.740798] (&(&cq->lock)->rlock){..-.}
[ 154.740800]
... which became SOFTIRQ-irq-safe at:
[ 154.752163] _raw_spin_lock_irqsave+0x3e/0x50
[ 154.757163] mlx4_ib_poll_cq+0x36/0x900 [mlx4_ib]
[ 154.762554] ipoib_tx_poll+0x4a/0xf0 [ib_ipoib]
...
to a SOFTIRQ-irq-unsafe lock:
[ 154.815603] (&(&qp_table->lock)->rlock){+.+.}
[ 154.815604]
... which became SOFTIRQ-irq-unsafe at:
[ 154.827718] ...
[ 154.827720] _raw_spin_lock+0x35/0x50
[ 154.833912] mlx4_qp_lookup+0x1e/0x50 [mlx4_core]
[ 154.839302] mlx4_flow_attach+0x3f/0x3d0 [mlx4_core]
Since mlx4_qp_lookup() is called only in process space, we can
simply replace the spin_un/lock calls with spin_un/lock_irq calls.
Fixes: 6dc06c08bef1 ("net/mlx4: Fix the check in attaching steering rules")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
BayTrail-based and newer Chromebooks describe their peripherals in ACPI;
unfortunately their description is not complete, and peripherals
drivers, such as driver for Atmel Touch controllers, has to resort to
DMI-matching to configure the peripherals properly. To avoid polluting
peripheral driver code, let's teach chromeos_laptop driver to supply
missing data via generic device properties.
Note we supply "compatible" string for Atmel peripherals not because it is
needed for matching devices and driver (matching is still done on ACPI HID
entries), but because peripherals driver will be using presence of
"compatible" property to determine if device properties have been attached
to the device, and fail to bind if they are absent.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
|
|
On newer PHYs, we need to select the expansion register to write with
setting bits [11:8] to 0xf. This was done correctly by bcm7xxx.c prior
to being migrated to generic code under bcm-phy-lib.c which
unfortunately used the older implementation from the BCM54xx days.
Fix this by creating an inline stub: bcm_write_exp_sel() which adds the
correct value (MII_BCM54XX_EXP_SEL_ER) and update both the Cygnus PHY
and BCM7xxx PHY drivers which require setting these bits.
broadcom.c is unchanged because some PHYs even use a different selector
method, so let them specify it directly (e.g: SerDes secondary selector).
Fixes: a1cba5613edf ("net: phy: Add Broadcom phy library for common interfaces")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We are currently doing auxiliary control register reads with the shadow
register value 0b111 (0x7) which incidentally is also the selector value
that should be present in bits [2:0]. Fix this by using the appropriate
selector mask which is defined (MII_BCM54XX_AUXCTL_SHDWSEL_MASK).
This does not have a functional impact yet because we always access the
MII_BCM54XX_AUXCTL_SHDWSEL_MISC (0x7) register in the current code.
This might change at some point though.
Fixes: 5b4e29005123 ("net: phy: broadcom: add bcm54xx_auxctl_read")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Trivial fix to spelling mistake in mlx4_dbg debug message and also
change the phrasing of the message so that is is more readable
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When enabling the sub-CRQ IRQ a previous update sent a H_EOI prior
to the enablement to clear any pending interrupts that may be present
across a partition migration. This fixed a firmware bug where a
migration could erroneously indicate that a H_EOI was pending.
The H_EOI should only be sent when enabling during a mobility
event though. Doing so at other time could wrong and can produce
extra driver output when IRQs are enabled when doing TX completion.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
New ICs (like the one on the Lenovo T480s) answer to
ETP_SMBUS_IAP_VERSION_CMD 4 bytes instead of 3. This corrupts the stack
as i2c_smbus_read_block_data() uses the values returned by the i2c
device to know how many data it need to return.
i2c_smbus_read_block_data() can read up to 32 bytes (I2C_SMBUS_BLOCK_MAX)
and there is no safeguard on how many bytes are provided in the return
value. Ensure we always have enough space for any future firmware.
Also 0-initialize the values to prevent any access to uninitialized memory.
Cc: <stable@vger.kernel.org> # v4.4.x, v4.9.x, v4.14.x, v4.15.x, v4.16.x
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: KT Liao <kt.liao@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
This time, Lenovo decided to go with different pieces in its latest
series of Thinkpads.
For those we have been able to test:
- the T480 is using Synaptics with an IBM trackpoint
-> it behaves properly with or without intertouch, there is no point
not using RMI4
- the X1 Carbon 6th gen is using Synaptics with an IBM trackpoint
-> the touchpad doesn't behave properly under PS/2 so we have to
switch it to RMI4 if we do not want to have disappointed users
- the X280 is using Synaptics with an ALPS trackpoint
-> the recent fixes in the trackpoint handling fixed it so upstream
now works fine with or without RMI4, and there is no point not
using RMI4
- the T480s is using an Elan touchpad, so that's a different story
Cc: <stable@vger.kernel.org> # v4.14.x, v4.15.x, v4.16.x
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: KT Liao <kt.liao@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Synaptics devices reported it has Intertouch support,
and it fails via PS/2 as following logs:
psmouse serio2: Failed to reset mouse on synaptics-pt/serio0
psmouse serio2: Failed to enable mouse on synaptics-pt/serio0
Set these new devices to use SMBus to fix this issue, then they report
SMBus version 3 is using, patch:
https://patchwork.kernel.org/patch/9989547/ enabled SMBus ver 3 and
makes synaptics devices work fine on SMBus mode.
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
trackpoints should use RMI
Lenovo use two different trackpoints in the fifth generation Thinkpad X1
Carbon. Both are accessible over SMBUS/RMI but the pnpIDs are missing.
This patch is for the Elantech trackpoint specifically which also
reports SMB version 3 so rmi_smbus needs to be updated in order to
handle it.
For the record, I was not the first one to come up with this patch as it
has been floating around the internet for a while now. However, I have
spent significant time with testing and my efforts to find the original
author of the patch have been unsuccessful.
Signed-off-by: Edvard Holst <edvard.holst@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.17
Hopefully the last fixes for 4.17. ssb is again causing problems so we
had to revert a commit and fix it better. Also a small fix to bcma and
some MAINTAINERS file updates.
ssb
* fix regression with all module PCI cards, for example using b43 and
b44 drivers
* try again fixing a MIPS linker error
bcma
* fix truncated info log messages
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The touchpad on Lenovo Carbon X1 Gen 5 (2017 - Kabylake) is accessible over
SMBUS/RMI, so let's activate it by default.
Cc: stable@vger.kernel.org
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
When link is down, writes to the device might fail with
-EIO. Userspace needs an indication when the status is resolved. As a
fix, tun_net_open() attempts to wake up writers - but that is only
effective if SOCKWQ_ASYNC_NOSPACE has been set in the past. This is
not the case of vhost_net which only poll for EPOLLOUT after it meets
errors during sendmsg().
This patch fixes this by making sure SOCKWQ_ASYNC_NOSPACE is set when
socket is not writable or device is down to guarantee EPOLLOUT will be
raised in either tun_chr_poll() or tun_sock_write_space() after device
is up.
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Eric Dumazet <edumazet@google.com>
Fixes: 1bd4978a88ac2 ("tun: honor IFF_UP in tun_get_user()")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jason Wang says:
====================
Fix several issues of virtio-net mergeable XDP
Please review the patches that tries to fix several issues of
virtio-net mergeable XDP.
Changes from V1:
- check against 1 before decreasing instead of resetting to 1
- typoe fixes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We need to drop refcnt to xdp_page if we see a gso packet. Otherwise
it will be leaked. Fixing this by moving the check of gso packet above
the linearizing logic. While at it, remove useless comment as well.
Cc: John Fastabend <john.fastabend@gmail.com>
Fixes: 72979a6c3590 ("virtio_net: xdp, add slowpath case for non contiguous buffers")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If we successfully linearize the packet, num_buf will be set to zero
which may confuse error handling path which assumes num_buf is at
least 1 and this can lead the code tries to pop the descriptor of next
buffer. Fixing this by checking num_buf against 1 before decreasing.
Fixes: 4941d472bf95 ("virtio-net: do not reset during XDP set")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We should not go for the error path after successfully transmitting a
XDP buffer after linearizing. Since the error path may try to pop and
drop next packet and increase the drop counters. Fixing this by simply
drop the refcnt of original page and go for xmit path.
Fixes: 72979a6c3590 ("virtio_net: xdp, add slowpath case for non contiguous buffers")
Cc: John Fastabend <john.fastabend@gmail.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After a linearized packet was redirected by XDP, we should not go for
the err path which will try to pop buffers for the next packet and
increase the drop counter. Fixing this by just drop the page refcnt
for the original page.
Fixes: 186b3c998c50 ("virtio-net: support XDP_REDIRECT")
Reported-by: David Ahern <dsahern@gmail.com>
Tested-by: David Ahern <dsahern@gmail.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
A handful of fixes:
* hwsim radio dump wasn't working for the first radio
* mesh was updating statistics incorrectly
* a netlink message allocation was possibly too short
* wiphy name limit was still too long
* in certain cases regdb query could find a NULL pointer
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD fix from Lee Jones:
"A single cros_ec_spi fix correcting the handling for long-running
commands"
* tag 'mfd-fixes-4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
mfd: cros_ec: Retry commands when EC is known to be busy
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha
Pull alpha fixes from Matt Turner:
"A few small changes for alpha"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha:
alpha: io: reorder barriers to guarantee writeX() and iowriteX() ordering #2
alpha: simplify get_arch_dma_ops
alpha: use dma_direct_ops for jensen
|
|
We have had problems displaying fbdev after a resume and as a
workaround we have had to call vmw_fb_refresh(). This has had
a number of unwanted side-effects. The root of the problem was,
however that the coalesced fbdev dirty region was not empty on
the first dirty_mark() after a resume, so a flush was never
scheduled.
Fix this by force scheduling an fbdev flush after resume, and
remove the workaround.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
Reviewed-by: Deepak Rawat <drawat@vmware.com>
|
|
The error paths were leaking opened channels.
Fix by using dedicated error paths.
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
|
|
Depending on whether the kernel is compiled with frame-pointer or not,
the temporary memory location used for the bp parameter in these macros
is referenced relative to the stack pointer or the frame pointer.
Hence we can never reference that parameter when we've modified either
the stack pointer or the frame pointer, because then the compiler would
generate an incorrect stack reference.
Fix this by pushing the temporary memory parameter on a known location on
the stack before modifying the stack- and frame pointers.
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
|
|
The reuseport_bpf_numa test case fails there's no numa support. The
test shouldn't fail if there's no support it should be skipped.
Fixes: 3c2c3c16aaf6 ("reuseport, bpf: add test case for bpf_get_numa_node_id")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
syzkaller reports for buffer overflow for interface name
when starting sync daemons [1]
What we do is that we copy user structure into larger stack
buffer but later we search NUL past the stack buffer.
The same happens for sched_name when adding/editing virtual server.
We are restricted by IP_VS_SCHEDNAME_MAXLEN and IP_VS_IFNAME_MAXLEN
being used as size in include/uapi/linux/ip_vs.h, so they
include the space for NUL.
As using strlcpy is wrong for unsafe source, replace it with
strscpy and add checks to return EINVAL if source string is not
NUL-terminated. The incomplete strlcpy fix comes from 2.6.13.
For the netlink interface reduce the len parameter for
IPVS_DAEMON_ATTR_MCAST_IFN and IPVS_SVC_ATTR_SCHED_NAME,
so that we get proper EINVAL.
[1]
kernel BUG at lib/string.c:1052!
invalid opcode: 0000 [#1] SMP KASAN
Dumping ftrace buffer:
(ftrace buffer empty)
Modules linked in:
CPU: 1 PID: 373 Comm: syz-executor936 Not tainted 4.17.0-rc4+ #45
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
RIP: 0010:fortify_panic+0x13/0x20 lib/string.c:1051
RSP: 0018:ffff8801c976f800 EFLAGS: 00010282
RAX: 0000000000000022 RBX: 0000000000000040 RCX: 0000000000000000
RDX: 0000000000000022 RSI: ffffffff8160f6f1 RDI: ffffed00392edef6
RBP: ffff8801c976f800 R08: ffff8801cf4c62c0 R09: ffffed003b5e4fb0
R10: ffffed003b5e4fb0 R11: ffff8801daf27d87 R12: ffff8801c976fa20
R13: ffff8801c976fae4 R14: ffff8801c976fae0 R15: 000000000000048b
FS: 00007fd99f75e700(0000) GS:ffff8801daf00000(0000)
knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000200001c0 CR3: 00000001d6843000 CR4: 00000000001406e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
strlen include/linux/string.h:270 [inline]
strlcpy include/linux/string.h:293 [inline]
do_ip_vs_set_ctl+0x31c/0x1d00 net/netfilter/ipvs/ip_vs_ctl.c:2388
nf_sockopt net/netfilter/nf_sockopt.c:106 [inline]
nf_setsockopt+0x7d/0xd0 net/netfilter/nf_sockopt.c:115
ip_setsockopt+0xd8/0xf0 net/ipv4/ip_sockglue.c:1253
udp_setsockopt+0x62/0xa0 net/ipv4/udp.c:2487
ipv6_setsockopt+0x149/0x170 net/ipv6/ipv6_sockglue.c:917
tcp_setsockopt+0x93/0xe0 net/ipv4/tcp.c:3057
sock_common_setsockopt+0x9a/0xe0 net/core/sock.c:3046
__sys_setsockopt+0x1bd/0x390 net/socket.c:1903
__do_sys_setsockopt net/socket.c:1914 [inline]
__se_sys_setsockopt net/socket.c:1911 [inline]
__x64_sys_setsockopt+0xbe/0x150 net/socket.c:1911
do_syscall_64+0x1b1/0x800 arch/x86/entry/common.c:287
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x447369
RSP: 002b:00007fd99f75dda8 EFLAGS: 00000246 ORIG_RAX: 0000000000000036
RAX: ffffffffffffffda RBX: 00000000006e39e4 RCX: 0000000000447369
RDX: 000000000000048b RSI: 0000000000000000 RDI: 0000000000000003
RBP: 0000000000000000 R08: 0000000000000018 R09: 0000000000000000
R10: 00000000200001c0 R11: 0000000000000246 R12: 00000000006e39e0
R13: 75a1ff93f0896195 R14: 6f745f3168746576 R15: 0000000000000001
Code: 08 5b 41 5c 41 5d 41 5e 41 5f 5d c3 0f 0b 48 89 df e8 d2 8f 48 fa eb
de 55 48 89 fe 48 c7 c7 60 65 64 88 48 89 e5 e8 91 dd f3 f9 <0f> 0b 90 90
90 90 90 90 90 90 90 90 90 55 48 89 e5 41 57 41 56
RIP: fortify_panic+0x13/0x20 lib/string.c:1051 RSP: ffff8801c976f800
Reported-and-tested-by: syzbot+aac887f77319868646df@syzkaller.appspotmail.com
Fixes: e4ff67513096 ("ipvs: add sync_maxlen parameter for the sync daemon")
Fixes: 4da62fc70d7c ("[IPVS]: Fix for overflows")
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Only CPUs which speculate can speculate. Therefore, it seems prudent
to test for cpu_no_speculation first and only then determine whether
a specific speculating CPU is susceptible to store bypass speculation.
This is underlined by all CPUs currently listed in cpu_no_speculation
were present in cpu_no_spec_store_bypass as well.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: bp@suse.de
Cc: konrad.wilk@oracle.com
Link: https://lkml.kernel.org/r/20180522090539.GA24668@light.dominikbrodowski.net
|
|
The X86_FEATURE_SSBD is an synthetic CPU feature - that is
it bit location has no relevance to the real CPUID 0x7.EBX[31]
bit position. For that we need the new CPU feature name.
Fixes: 52817587e706 ("x86/cpufeatures: Disentangle SSBD enumeration")
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: kvm@vger.kernel.org
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: stable@vger.kernel.org
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Link: https://lkml.kernel.org/r/20180521215449.26423-2-konrad.wilk@oracle.com
|
