| Age | Commit message (Collapse) | Author |
|---|
|
TI DA8xx/OMAPL13x/AM17xx/AM18xx SoCs have extra UART registers beyond
the standard 8250 registers, so we need a new compatible string to
indicate this. Also, at least one of these registers uses the full 32
bits, so we need to specify reg-io-width in addition to reg-shift.
"ns16550a" is left in the compatible specification since it does work
as long as the bootloader configures the SoC UART power management
registers.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
FDT harcoded partition table does not match that one in historical
TI's 2.6.37 kernel and non legacy kernels even use different ECC scheme,
yet noone complained, so remove it altogether.
Also, UBI volumes instead of partitions are used since u-boot-2016.09.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
10/100 Mbps"
According to errata i880 description the speed of Ethernet port 1 on AM572x
SoCs rev 1.1 should be limited to 10/100Mbps, because RGMII2 Switching
Characteristics are not compatible with 1000 Mbps operation [1].
The issue is fixed with Rev 2.0 silicon.
Hence, rework Beagle-X15 and Begale-X15-revb1 to use phy-handle instead of
phy_id and apply corresponding limitation to the Ethernet Phy 1.
[1] http://www.ti.com/lit/er/sprz429j/sprz429j.pdf
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
As the bootloader passes the NAND and the SPI flash partition tables
there is no need to keep them in the kernel device tree.
Removed them.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
TI DRA72-EVM Rev C has two DP83867 ethernet phys which support IRQ
generation in case of phy/link status changes. The INT/PWDN lines from both
DP83867 phys are wired to DRA7 gpio6.16, so reflect the same in DT.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This prevents having to poll peripheral USB port cable status.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Signed-off-by: Loic Pallardy <loic.pallardy.chotard@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Rename dmu_reserved to delta_reserved
Rename st231_dmu to st231_delta
Update the delta_reserved memory region start address
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
This node is unused, remove it
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
This node is unused, remove it
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Update the start address of gp0_reserved memory region
and enable it
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
The clock parent was lower than child clock which is not correct.
In some use case, it leads to division by zero.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
|
|
This patch adds DT node for STMicroelectronics
DELTA V4L2 video decoder
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
|
|
Only fdma0 instance is used for audio, so disable the
2 others instances.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Enable High Quality Video Data Plane which is
an hardware IP dedicated to video rendering.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
As sti-hda is only available on STiH410-B2120,
disable it in STiH410.dtsi and enable it at board level.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
There are no Exynos4212 based boards in mainline, so there is no need to
keep additional files for SoCs, which are never used. This patch removes
support for Exynos4212 SoCs and moves previously shared Exynos4412
definitions to a single file to simplify future maintenance.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
The Axentia TSE-850 is a SAMA5D3-based device designed to generate
FM subcarrier signals.
Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
The sama5d36ek CMP board is the variant of sama5d3xek board.
It is equipped with the low-power DDR2 SDRAM, PMIC ACT8865 and
some power rail. Its main purpose is used to measure the power
consumption.
The difference of the sama5d36ek CMP dts from sama5d36ek dts is
listed as below.
1. The USB host nodes are removed, that is, the USB host is disabled.
2. The gpio_keys node is added to wake up from the sleep.
3. The LCD isn't supported due to the pins for LCD are conflicted
with gpio_keys.
4. The adc0 node support the pinctrl sleep state to fix the over
consumption on VDDANA.
As said in errata, "When the USB host ports are used in high speed
mode (EHCI), it is not possible to suspend the ports if no device is
attached on each port. This leads to increased power consumption even
if the system is in a low power mode." That is why the the USB host
is disabled.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
The sama5d2 SoC has Synchronous Serial Controller which provides
synchronous communication link with external devices.
It's generally used in audio and telecom applications such as
I2S, Short Frame Sync, Long Frame Sync.
Signed-off-by: Alex Gershgorin <alex.gershgorin@qcore.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Use DMA for UART3 as we have enough channels and to show how to
specify DMA use with serial nodes.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Now that DMA1 is defined, use it to distribute channel usage among the two
controllers.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
The sama5d2 SoC has a second DMA controller and can be used just like DMA0.
By default both DMA controllers are configured as "Secure" in
MATRIX_SPSELR so we can use whichever we want in a "single Secure World"
configuration.
Surprisingly the DMA1 has a lower address than DMA0. To avoid confusion
place it after DMA0 node anyway.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Enable UART1 and use DMA configuration with it.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Some peripherals are "Programmable Secure" but left as "Secure" by default.
If tried to be connected to Non-Secure DMA controller, the possibility to
leak secure data is prevented so using these peripherals with DMA1 is not
possible with this default configuration (MATRIX_SPSELR registers setup by
bootloader).
Move them to DMA0 which is an "Always-Secure" DMA controller.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
The new size (0x100) also matches the size given in sama5d3.dtsi
Documentation reference: section 43.6 "Universal Asynchronous
Receiver Transmitter (UART) User Interface", table 43-4 "Register
Mapping" in [1].
[1] Atmel-11121F-ATARM-SAMA5D3-Series-Datasheet_02-Feb-16
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Romulus is an OpenPower machine with an ast2500 BMC. It has NCSI
networking and 512MB of RAM.
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Palmettos have 512MB of memory as opposed to the previously thought
256MB. Update the device trees accordingly.
We run the uart at 115200.
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
When used as a BMC, the host expects to be able to use 16MB of
framebuffer memory at the top of RAM.
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
The pin controller's child nodes expose the functions currently
implemented in the g5 pin controller driver.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
The pin controller's child nodes expose the functions currently
implemented in the the g4 pin controller driver.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
This patch include auxiliary clock definition (clocks which are not derived
from system clock.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
|
|
This patch adds an external I2S clock in the DT.
The I2S clock could be derived from an external I2S clock or by I2S pll.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
|
|
Enable analog to digital converter on stm32f429i-eval board.
It has on-board potentimeter wired to ADC3 in8 analog pin and
uses fixed regulator to provide reference voltage.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
|
|
Add ADC support & pinctrl analog phandle (adc3_in8) to stm32f429.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
|
|
This patch adds USART3 pin configuration on PB10/PA11 pins
for STM32F469I-DISCO board.
Signed-off-by: Bruno Herrera <bruherrera@gmail.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
|
|
This patch fix memory size to support 16MB of external SDRAM.
Signed-off-by: Bruno Herrera <bruherrera@gmail.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
|
|
Creation of dt include file for specific stm32f4 clocks.
These specific clocks are not derived from system clock (SYSCLOCK)
We should use index 1 to use these clocks in DT.
e.g. <&rcc 1 CLK_LSI>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Acked-by: Rob Herring <robh@kernel.org>
|
|
Enable VPIF for video captpure and configure input channel 0, used for
composite input.
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
Enable VPIF node for video capture, and configure ports. EVM board
uses channel 0 for composite input and channel 1 S-Video input.
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
Add VPIF node and pins to da850 SoC. VPIF has two input channels which
can be described using the standard DT ports and endpoints.
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
[nsekhar@ti.com: drop stray newline, typo fixes in commit message]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
Add .dts file for rev. C of the board by factoring out commonalities
into a shared include file (vf610-zii-dev-rev-b-c.dtsi) and deriving
revision specific file from it (vf610-zii-dev-rev-b.dts and
vf610-zii-dev-reb-c.dts).
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Stefan Agner <stefan@agner.ch>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: andrew@lunn.ch
Cc: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Cc: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Cc: cphealy@gmail.com
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Remove pwm0grp since it is:
a) Not referenced anywhere in the DTS file (unlike Tower board it
is based on, this board does not use/expose FTM0)
b) Configures PTB2 and PTB3 in a way that contradicts
pinctrl-mdio-mux
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Stefan Agner <stefan@agner.ch>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: andrew@lunn.ch
Cc: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Cc: cphealy@gmail.com
Tested-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Use common board file and support SATA interface additionally.
Specify the dtb file for i.MX6 build.
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
