| Age | Commit message (Collapse) | Author |
|---|
|
I recently debugged a DMA mapping oops where a driver was trying to map
a buffer returned from request_firmware() with dma_map_single(). Memory
returned from request_firmware() is mapped into the vmalloc region and
this isn't a valid region to map with dma_map_single() per the DMA
documentation's "What memory is DMA'able?" section.
Unfortunately, we don't really check that in the DMA debugging code, so
enabling DMA debugging doesn't help catch this problem. Let's add a new
DMA debug function to check for a vmalloc address or an invalid virtual
address and print a warning if this happens. This makes it a little
easier to debug these sorts of problems, instead of seeing odd behavior
or crashes when drivers attempt to map the vmalloc space for DMA.
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Debug data dump is not working in flows that stop the device is used
in their error handling. During these flows the op mode mutex is
locked until the device stops. Because of that, any assert generated
from the firmware can be handled only after the device already
stopped.
Since dumping cannot occour after stopping the device, split the the
dump function to two parts, Part that handles locking, and the part
that starts the actual dumping and call the second part in the op mode
stop device function.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Currently in case of DCM with P2P GO where BSS DTIM interval < 220 msec
the fw fails to allocate events for the P2P GO dtim due to long passive
scan events.
Fix this by requesting all scans in this scenario to be fragmented with
fast balance scan time settings. The only exception is in case
fragmented scan was planned to be set due to low latency or high
throughput reason, set the scan timing as planned.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Fast balance scan is similar to SCAN_TYPE_MILD, but this scan is
fragmented and has shorter out of operating channel time,
and therefore better match low latency scenarios.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Split TX tracing to be per TB. This is needed now that
AMSDUs can be sent and skb can be larger than trace
limit.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Andrei Vagin <avagin@gmail.com> reported:
> Accoding to the man page, the user should not set si_signo, it has to be set
> by kernel.
>
> $ man 2 rt_sigqueueinfo
>
> The uinfo argument specifies the data to accompany the signal. This
> argument is a pointer to a structure of type siginfo_t, described in
> sigaction(2) (and defined by including <sigaction.h>). The caller
> should set the following fields in this structure:
>
> si_code
> This must be one of the SI_* codes in the Linux kernel source
> file include/asm-generic/siginfo.h, with the restriction that
> the code must be negative (i.e., cannot be SI_USER, which is
> used by the kernel to indicate a signal sent by kill(2)) and
> cannot (since Linux 2.6.39) be SI_TKILL (which is used by the
> kernel to indicate a signal sent using tgkill(2)).
>
> si_pid This should be set to a process ID, typically the process ID of
> the sender.
>
> si_uid This should be set to a user ID, typically the real user ID of
> the sender.
>
> si_value
> This field contains the user data to accompany the signal. For
> more information, see the description of the last (union sigval)
> argument of sigqueue(3).
>
> Internally, the kernel sets the si_signo field to the value specified
> in sig, so that the receiver of the signal can also obtain the signal
> number via that field.
>
> On Tue, Sep 25, 2018 at 07:19:02PM +0200, Eric W. Biederman wrote:
>>
>> If there is some application that calls sigqueueinfo directly that has
>> a problem with this added sanity check we can revisit this when we see
>> what kind of crazy that application is doing.
>
>
> I already know two "applications" ;)
>
> https://github.com/torvalds/linux/blob/master/tools/testing/selftests/ptrace/peeksiginfo.c
> https://github.com/checkpoint-restore/criu/blob/master/test/zdtm/static/sigpending.c
>
> Disclaimer: I'm the author of both of them.
Looking at the kernel code the historical behavior has alwasy been to prefer
the signal number passed in by the kernel.
So sigh. Implmenet __copy_siginfo_from_user and __copy_siginfo_from_user32 to
take that signal number and prefer it. The user of ptrace will still
use copy_siginfo_from_user and copy_siginfo_from_user32 as they do not and
never have had a signal number there.
Luckily this change has never made it farther than linux-next.
Fixes: e75dc036c445 ("signal: Fail sigqueueinfo if si_signo != sig")
Reported-by: Andrei Vagin <avagin@gmail.com>
Tested-by: Andrei Vagin <avagin@gmail.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
|
|
When we TX AMSDU, we shouldn't pad the packet. In the past,
we were building AMSDU only in transport layer, and gen2
functions are built based on this. However, now that op mode
may build AMSDUs, we need to take care of padding also in
gen2 "non-pcie-amsdu" path.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
In the past, we needed to program the keys when entering D3. This was
since we replaced the image. However, now that there is a single
image, this is no longer needed. Note that RSC is sent separately in
a new command. This solves issues with newer devices that support PN
offload. Since driver re-sent the keys, the PN got zeroed and the
receiver dropped the next packets, until PN caught up again.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Provide function to find a ccwgroup device by its busid.
Acked-by: Sebastian Ott <sebott@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
This patch is an extension to the zcrypt device driver to provide,
support and maintain multiple zcrypt device nodes. The individual
zcrypt device nodes can be restricted in terms of crypto cards,
domains and available ioctls. Such a device node can be used as a
base for container solutions like docker to control and restrict
the access to crypto resources.
The handling is done with a new sysfs subdir /sys/class/zcrypt.
Echoing a name (or an empty sting) into the attribute "create" creates
a new zcrypt device node. In /sys/class/zcrypt a new link will appear
which points to the sysfs device tree of this new device. The
attribute files "ioctlmask", "apmask" and "aqmask" in this directory
are used to customize this new zcrypt device node instance. Finally
the zcrypt device node can be destroyed by echoing the name into
/sys/class/zcrypt/destroy. The internal structs holding the device
info are reference counted - so a destroy will not hard remove a
device but only marks it as removable when the reference counter drops
to zero.
The mask values are bitmaps in big endian order starting with bit 0.
So adapter number 0 is the leftmost bit, mask is 0x8000... The sysfs
attributes accept 2 different formats:
* Absolute hex string starting with 0x like "0x12345678" does set
the mask starting from left to right. If the given string is shorter
than the mask it is padded with 0s on the right. If the string is
longer than the mask an error comes back (EINVAL).
* Relative format - a concatenation (done with ',') of the
terms +<bitnr>[-<bitnr>] or -<bitnr>[-<bitnr>]. <bitnr> may be any
valid number (hex, decimal or octal) in the range 0...255. Here are
some examples:
"+0-15,+32,-128,-0xFF"
"-0-255,+1-16,+0x128"
"+1,+2,+3,+4,-5,-7-10"
A simple usage examples:
# create new zcrypt device 'my_zcrypt':
echo "my_zcrypt" >/sys/class/zcrypt/create
# go into the device dir of this new device
echo "my_zcrypt" >create
cd my_zcrypt/
ls -l
total 0
-rw-r--r-- 1 root root 4096 Jul 20 15:23 apmask
-rw-r--r-- 1 root root 4096 Jul 20 15:23 aqmask
-r--r--r-- 1 root root 4096 Jul 20 15:23 dev
-rw-r--r-- 1 root root 4096 Jul 20 15:23 ioctlmask
lrwxrwxrwx 1 root root 0 Jul 20 15:23 subsystem -> ../../../../class/zcrypt
...
# customize this zcrypt node clone
# enable only adapter 0 and 2
echo "0xa0" >apmask
# enable only domain 6
echo "+6" >aqmask
# enable all 256 ioctls
echo "+0-255" >ioctls
# now the /dev/my_zcrypt may be used
# finally destroy it
echo "my_zcrypt" >/sys/class/zcrypt/destroy
Please note that a very similar 'filtering behavior' also applies to
the parent z90crypt device. The two mask attributes apmask and aqmask
in /sys/bus/ap act the very same for the z90crypt device node. However
the implementation here is totally different as the ap bus acts on
bind/unbind of queue devices and associated drivers but the effect is
still the same. So there are two filters active for each additional
zcrypt device node: The adapter/domain needs to be enabled on the ap
bus level and it needs to be active on the zcrypt device node level.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/vfio-ccw into fixes
Pull vfio-ccw from Cornelia Huck with the following changes:
- Another fix for vfio-ccw: make sure it accesses the correct entries
in the pfn_array_table arrays when checking pinned pages.
|
|
On i.MX6UL/i.MX6ULL, accessing OCOTP directly is wrong because
the ocotp clock needs to be enabled first. Add support for reading
OCOTP through the nvmem API, and keep the old method there to
support old dtb.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
RK3899 has one cluster with 4 small cores, and another one with 2 big
cores, with cores in different clusters having different OPPs and thus
needing separate set of tunables. Let's enable this via
"have_governor_per_policy" platform data.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm into pm-opp
Pull more operating performance points (OPP) framework updates for 4.20
from Viresh Kumar:
"That contains some important fixes reported recently."
* 'opp/linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
PM / OPP: _of_add_opp_table_v2(): increment count only if OPP is added
cpufreq: dt: Try freeing static OPPs only if we have added them
OPP: Return error on error from dev_pm_opp_get_opp_count()
OPP: Improve error handling in dev_pm_opp_of_cpumask_add_table()
|
|
There was a small race when removing the sbshc module where
smbus_alarm() had queued acpi_smbus_callback() for deferred execution
but it hadn't been run yet, so that when it did run hc had been freed
and the module unloaded, resulting in an invalid paging request.
A similar race existed when removing the sbs module with regards to
acpi_sbs_callback() (which is called from acpi_smbus_callback()).
We therefore need to ensure no callbacks are pending or executing before
the cleanups are done and the modules are removed.
Signed-off-by: Ronald Tschalär <ronald@innovation.ch>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
On Apple machines, plugging-in or unplugging the power triggers a GPE
for the EC. Since these machines expose an SBS device, this GPE ends
up triggering the acpi_sbs_callback(). This in turn tries to get the
status of the SBS charger. However, on MBP13,* and MBP14,* machines,
performing the smbus-read operation to get the charger's status triggers
the EC's GPE again. The result is an endless re-triggering and handling
of that GPE, consuming significant CPU resources (> 50% in irq).
In the end this is quite similar to commit 3031cddea633 (ACPI / SBS:
Don't assume the existence of an SBS charger), except that on the above
machines a status of all 1's is returned. And like there, we just want
ignore the charger here.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=198169
Signed-off-by: Ronald Tschalär <ronald@innovation.ch>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
runtime refcount fix for mst connectors.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Ben Skeggs <bskeggs@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CABDvA=nydWjs26=TZHqistLXjCwm-vHmrisbP6K=FMZ5gW1wnQ@mail.gmail.com
|
|
This place should want to initialize array, not a element,
so it should be sizeof(array) instead of sizeof(element)
but now this array only has one element, so no error in
this condition that XFRM_MAX_OFFLOAD_DEPTH is 1
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
if tstats of a device is not allocated, this device is not
registered correctly and can not be used.
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
Replace "fallthru" with a proper "fall through" annotation.
This fix is part of the ongoing efforts to enabling
-Wimplicit-fallthrough
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace "fallthru" with a proper "fall through" annotation.
This fix is part of the ongoing efforts to enabling
-Wimplicit-fallthrough
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
arch/sparc/vdso/Makefile is a replica of arch/x86/entry/vdso/Makefile.
Clean-up the Makefile in the same way as I did for x86:
- Remove unnecessary export
- Put the generated linker script to $(obj)/ instead of $(src)/
- Simplify cmd_vdso2c
The corresponding x86 commits are:
- 61615faf0a89 ("x86/build/vdso: Remove unnecessary export in Makefile")
- 1742ed2088cc ("x86/build/vdso: Put generated linker scripts to $(obj)/")
- c5fcdbf15523 ("x86/build/vdso: Simplify 'cmd_vdso2c'")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A null check before a kfree is redundant, so remove it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the quest to remove all stack VLA usage from the kernel[1], this
allocates a fixed size array for the maximum number of cookies and
adds a runtime sanity check.
[1] https://lkml.kernel.org/r/CA+55aFzCG-zNmZwX4A2FQpadafLfEzK6CC=qPXydAacU1
RqZWA@mail.gmail.com
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the of_get_child_by_name() helper instead of open coding searching
for the '/options' node. This removes directly accessing the name
pointer as well.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: sparclinux@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: sparclinux@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On Sun Ultra 5, it happens that the dot clock is not set up properly for
some videomodes. For example, if we set the videomode "r1024x768x60" in
the firmware, Linux would incorrectly set a videomode with refresh rate
180Hz when booting (suprisingly, my LCD monitor can display it, although
display quality is very low).
The reason is this: Older mach64 cards set the divider in the register
VCLK_POST_DIV. The register has four 2-bit fields (the field that is
actually used is specified in the lowest two bits of the register
CLOCK_CNTL). The 2 bits select divider "1, 2, 4, 8". On newer mach64 cards,
there's another bit added - the top four bits of PLL_EXT_CNTL extend the
divider selection, so we have possible dividers "1, 2, 4, 8, 3, 5, 6, 12".
The Linux driver clears the top four bits of PLL_EXT_CNTL and never sets
them, so it can work regardless if the card supports them. However, the
sparc64 firmware may set these extended dividers during boot - and the
mach64 driver detects incorrect dot clock in this case.
This patch makes the driver read the additional divider bit from
PLL_EXT_CNTL and calculate the initial refresh rate properly.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Acked-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Ville Syrjälä <syrjala@sci.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Eugene Syromiatnikov says:
====================
net/smc: userspace breakage fixes
These two patches correct some userspace-affecting issues introduced
during 4.19 development cycle, specifically:
* New structure "struct smcd_diag_dmbinfo" has been defined in a way
that would lead to different layout of the structure on most 32-bit
ABIs in comparison with layout on 64-bit ABIs;
* One of the commits renamed an UAPI-exposed field name.
Changes since v1:
* Managed not to forget to add --cover-letter.
* Commit ID format in commit message has been changed in accordance
with Sergei Shtylyov's recommendations.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit c601171d7a60 ("net/smc: provide smc mode in smc_diag.c") changed
the name of diag_fallback field of struct smc_diag_msg structure
to diag_mode. However, this structure is a part of UAPI, and this change
breaks user space applications that use it ([1], for example). Since
the new name is more suitable, convert the field to a union that provides
access to the data via both the new and the old name.
[1] https://gitlab.com/strace/strace/blob/v4.24/netlink_smc_diag.c#L165
Fixes: c601171d7a60 ("net/smc: provide smc mode in smc_diag.c")
Signed-off-by: Eugene Syromiatnikov <esyr@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 4b1b7d3b30a6 ("net/smc: add SMC-D diag support") introduced
new UAPI-exposed structure, struct smcd_diag_dmbinfo. However,
it's not usable by compat binaries, as it has different layout there.
Probably, the most straightforward fix that will avoid similar issues
in the future is to use __aligned_u64 for 64-bit fields.
Fixes: 4b1b7d3b30a6 ("net/smc: add SMC-D diag support")
Signed-off-by: Eugene Syromiatnikov <esyr@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
cls_u32.c misuses refcounts for struct tc_u_hnode - it counts references
via ->hlist and via ->tp_root together. u32_destroy() drops the former
and, in case when there had been links, leaves the sucker on the list.
As the result, there's nothing to protect it from getting freed once links
are dropped.
That also makes the "is it busy" check incapable of catching the root
hnode - it *is* busy (there's a reference from tp), but we don't see it as
something separate. "Is it our root?" check partially covers that, but
the problem exists for others' roots as well.
AFAICS, the minimal fix preserving the existing behaviour (where it doesn't
include oopsen, that is) would be this:
* count tp->root and tp_c->hlist as separate references. I.e.
have u32_init() set refcount to 2, not 1.
* in u32_destroy() we always drop the former;
in u32_destroy_hnode() - the latter.
That way we have *all* references contributing to refcount. List
removal happens in u32_destroy_hnode() (called only when ->refcnt is 1)
an in u32_destroy() in case of tc_u_common going away, along with
everything reachable from it. IOW, that way we know that
u32_destroy_key() won't free something still on the list (or pointed to by
someone's ->root).
Reproducer:
tc qdisc add dev eth0 ingress
tc filter add dev eth0 parent ffff: protocol ip prio 100 handle 1: \
u32 divisor 1
tc filter add dev eth0 parent ffff: protocol ip prio 200 handle 2: \
u32 divisor 1
tc filter add dev eth0 parent ffff: protocol ip prio 100 \
handle 1:0:11 u32 ht 1: link 801: offset at 0 mask 0f00 shift 6 \
plus 0 eat match ip protocol 6 ff
tc filter delete dev eth0 parent ffff: protocol ip prio 200
tc filter change dev eth0 parent ffff: protocol ip prio 100 \
handle 1:0:11 u32 ht 1: link 0: offset at 0 mask 0f00 shift 6 plus 0 \
eat match ip protocol 6 ff
tc filter delete dev eth0 parent ffff: protocol ip prio 100
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix 5 warnings and 14 checks issued by checkpatch.pl:
CHECK: Logical continuations should be on the previous line
+ if ((q->vars.qdelay < q->params.target / 2)
+ && (q->vars.prob < MAX_PROB / 5))
WARNING: line over 80 characters
+ q->params.tupdate = usecs_to_jiffies(nla_get_u32(tb[TCA_PIE_TUPDATE]));
CHECK: Blank lines aren't necessary after an open brace '{'
+{
+
CHECK: braces {} should be used on all arms of this statement
+ if (qlen < QUEUE_THRESHOLD)
[...]
+ else {
[...]
CHECK: Unbalanced braces around else statement
+ else {
CHECK: No space is necessary after a cast
+ if (delta > (s32) (MAX_PROB / (100 / 2)) &&
CHECK: Unnecessary parentheses around 'qdelay == 0'
+ if ((qdelay == 0) && (qdelay_old == 0) && update_prob)
CHECK: Unnecessary parentheses around 'qdelay_old == 0'
+ if ((qdelay == 0) && (qdelay_old == 0) && update_prob)
CHECK: Unnecessary parentheses around 'q->vars.prob == 0'
+ if ((q->vars.qdelay < q->params.target / 2) &&
+ (q->vars.qdelay_old < q->params.target / 2) &&
+ (q->vars.prob == 0) &&
+ (q->vars.avg_dq_rate > 0))
CHECK: Unnecessary parentheses around 'q->vars.avg_dq_rate > 0'
+ if ((q->vars.qdelay < q->params.target / 2) &&
+ (q->vars.qdelay_old < q->params.target / 2) &&
+ (q->vars.prob == 0) &&
+ (q->vars.avg_dq_rate > 0))
CHECK: Blank lines aren't necessary before a close brace '}'
+
+}
CHECK: Comparison to NULL could be written "!opts"
+ if (opts == NULL)
CHECK: No space is necessary after a cast
+ ((u32) PSCHED_TICKS2NS(q->params.target)) /
WARNING: line over 80 characters
+ nla_put_u32(skb, TCA_PIE_TUPDATE, jiffies_to_usecs(q->params.tupdate)) ||
CHECK: Blank lines aren't necessary before a close brace '}'
+
+}
CHECK: No space is necessary after a cast
+ .delay = ((u32) PSCHED_TICKS2NS(q->vars.qdelay)) /
WARNING: Missing a blank line after declarations
+ struct sk_buff *skb;
+ skb = qdisc_dequeue_head(sch);
WARNING: Missing a blank line after declarations
+ struct pie_sched_data *q = qdisc_priv(sch);
+ qdisc_reset_queue(sch);
WARNING: Missing a blank line after declarations
+ struct pie_sched_data *q = qdisc_priv(sch);
+ q->params.tupdate = 0;
Signed-off-by: Leslie Monis <lesliemonis@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no need to compare *val.vu32* with < 0 because
such variable is of type u32 (32 bits, unsigned), making it
impossible to hold a negative value. Fix this by removing
such comparison.
Also, initialize variable *max_val* to -1, just in case
it is not initialized to either BNXT_MSIX_VEC_MAX or
BNXT_MSIX_VEC_MIN_MAX before using it in a comparison
with val.vu32 at line 159:
if (val.vu32 > max_val)
Addresses-Coverity-ID: 1473915 ("Unsigned compared against 0")
Addresses-Coverity-ID: 1473920 ("Uninitialized scalar variable")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 2276f58ac589 ("udp: use a separate rx queue for packet reception")
turned static inline __skb_recv_udp() from being a trivial helper around
__skb_recv_datagram() into a UDP specific implementaion, making it
EXPORT_SYMBOL_GPL() at the same time.
There are external modules that got broken by __skb_recv_udp() not being
visible to them. Let's unbreak them by making __skb_recv_udp EXPORT_SYMBOL().
Rationale (one of those) why this is actually "technically correct" thing
to do: __skb_recv_udp() used to be an inline wrapper around
__skb_recv_datagram(), which itself (still, and correctly so, I believe)
is EXPORT_SYMBOL().
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Eric Dumazet <edumazet@google.com>
Fixes: 2276f58ac589 ("udp: use a separate rx queue for packet reception")
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The commit ca460b3c9627 ("percpu: introduce bitmap metadata blocks")
introduced bitmap metadata blocks. These metadata blocks are allocated
whenever a new chunk is created, but they are never freed. Fix it.
Fixes: ca460b3c9627 ("percpu: introduce bitmap metadata blocks")
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dennis Zhou <dennis@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.20
Second set of patches for 4.20. Heavy refactoring on mt76 continues
and the usual drivers in active development (iwlwifi, qtnfmac, ath10k)
getting new features. And as always, fixes and cleanup all over.
Major changes:
mt76
* more major refactoring to make it easier add new hardware support
* more work on mt76x0e support
* support for getting firmware version via ethtool
* add mt7650 PCI ID
iwlwifi
* HE radiotap cleanup and improvements
* reorder channel optimization for scans
* bump the FW API version
qtnfmac
* fixes for 'iw' output: rates for enabled SGI, 'dump station'
* expose more scan features to host: scan flush and dwell time
* inform cfg80211 when OBSS is not supported by firmware
wlcore
* add support for optional wakeirq
ath10k
* retrieve MAC address from system firmware if provided
* support extended board data download for dual-band QCA9984
* extended per sta tx statistics support via debugfs
* average ack rssi support for data frames
* speed up QCA6174 and QCA9377 firmware download using diag Copy
Engine
* HTT High Latency mode support needed by SDIO and USB support
* get STA power save state via debugfs
ath9k
* add reset functionality for airtime station debugfs file
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
My eyesight is not in good shape, which means that I have difficulty
reading the online Linux documentation. Specifically, body text is
oddly small compared to list items and the contrast of various text
elements is too low for me to be able to see easily.
Therefore, alter the HTML theme overrides to make the text larger and
increase the contrast for better visibility, and trust the typeface
choices of the reader's browser.
For the PDF output, increase the text size, use a sans-serif typeface
for sans-serif text, and use a serif typeface for "roman" serif text.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Acked-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
Current phrasing is ambiguous since it's unclear if attaching to a
children through PTRACE_TRACEME requires CAP_SYS_PTRACE. Rephrase the
sentence to make that clear.
Signed-off-by: Yves-Alexis Perez <corsac@corsac.net>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
The memory hotplug notifier description is about kernel internals rather
than admin/user visible API. Place it appropriately.
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
The memory hotplug description in Documentation/memory-hotplug.txt is
already formatted as ReST and can be easily added to admin-guide/mm
section.
While on it, slightly update formatting to make it consistent with the
doc-guide.
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
I wrote:
"Char/Misc fixes for 4.19-rc7
Here are 8 small fixes for some char/misc driver issues
Included here are:
- fpga driver fixes
- thunderbolt bugfixes
- firmware core revert/fix
- hv core fix
- hv tool fix
All of these have been in linux-next with no reported issues."
* tag 'char-misc-4.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
thunderbolt: Initialize after IOMMUs
thunderbolt: Do not handle ICM events after domain is stopped
firmware: Always initialize the fw_priv list object
docs: fpga: document fpga manager flags
fpga: bridge: fix obvious function documentation error
tools: hv: fcopy: set 'error' in case an unknown operation was requested
fpga: do not access region struct after fpga_region_unregister
Drivers: hv: vmbus: Use get/put_cpu() in vmbus_connect()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
I wrote:
"Serial driver fixes for 4.19-rc7
Here are 3 small serial driver fixes for 4.19-rc7
- 2 sh-sci bugfixes for reported issues
- a revert of the PM handling for the 8250_dw code
All of these have been in linux-next with no reported issues."
* tag 'tty-4.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
Revert "serial: sh-sci: Allow for compressed SCIF address"
Revert "serial: sh-sci: Remove SCIx_RZ_SCIFA_REGTYPE"
Revert "serial: 8250_dw: Fix runtime PM handling"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
I wrote:
"USB fixes for 4.19-rc7
Here are some small USB fixes for 4.19-rc7
These include:
- the usual xhci bugfixes for reported issues
- some new serial driver device ids
- bugfix for the option serial driver for some devices
- bugfix for the cdc_acm driver that has been there for a long time.
All of these have been in linux-next for a while with no reported
issues."
* tag 'usb-4.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: xhci-mtk: resume USB3 roothub first
xhci: Add missing CAS workaround for Intel Sunrise Point xHCI
usb: cdc_acm: Do not leak URB buffers
USB: serial: simple: add Motorola Tetra MTP6550 id
USB: serial: option: add two-endpoints device-id flag
USB: serial: option: improve Quectel EP06 detection
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Wolfram writes:
"i2c for 4.19
I2C has three driver bugfixes and a fix for a typo for you."
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: designware: Call i2c_dw_clk_rate() only when calculating timings
i2c: i2c-scmi: fix for i2c_smbus_write_block_data
i2c: i2c-isch: fix spelling mistake "unitialized" -> "uninitialized"
i2c: i2c-qcom-geni: Properly handle DMA safe buffers
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
James writes:
"SCSI fixes on 20181006
Small fix for an unititialized mutex in the qedi driver."
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: qedi: Initialize the stats mutex lock
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Michael writes:
"powerpc fixes for 4.19 #4
Four regression fixes.
A fix for a change to lib/xz which broke our zImage loader when
building with XZ compression. OK'ed by Herbert who merged the
original patch.
The recent fix we did to avoid patching __init text broke some 32-bit
machines, fix that.
Our show_user_instructions() could be tricked into printing kernel
memory, add a check to avoid that.
And a fix for a change to our NUMA initialisation logic, which causes
crashes in some kdump configurations.
Thanks to:
Christophe Leroy, Hari Bathini, Jann Horn, Joel Stanley, Meelis
Roos, Murilo Opsfelder Araujo, Srikar Dronamraju."
* tag 'powerpc-4.19-4' of https://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/numa: Skip onlining a offline node in kdump path
powerpc: Don't print kernel instructions in show_user_instructions()
powerpc/lib: fix book3s/32 boot failure due to code patching
lib/xz: Put CRC32_POLY_LE in xz_private.h
|
|
default_acl and acl of newly created inode will be initiated as
ACL_NOT_CACHED in vfs function inode_init_always() and later will be
updated by calling xxx_init_acl() in specific filesystems. However,
when default_acl and acl are NULL then they keep the value of
ACL_NOT_CACHED. This patch changes the code to cache NULL for acl /
default_acl in this case to save unnecessary ACL lookup attempt.
Signed-off-by: Chengguang Xu <cgxu519@gmx.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
|
|
|
