| Age | Commit message (Collapse) | Author |
|---|
|
The MV88E6060 switch has internal PHY registers at MDIO
addresses 0x00..0x04. Tie each port to the corresponding
PHY.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20231020-ixp4xx-usr8200-dtsfix-v1-1-3a8591dea259@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The Broadcom STB/CM PCIe HW core, which is also used in RPi SOCs, must be
deliberately set by the PCIe RC HW into one of three mutually exclusive
modes:
"safe" -- No CLKREQ# expected or required, refclk is always provided. This
mode should work for all devices but is not be capable of any refclk
power savings.
"no-l1ss" -- CLKREQ# is expected to be driven by the downstream device for
CPM and ASPM L0s and L1. Provides Clock Power Management, L0s, and L1,
but cannot provide L1 substate (L1SS) power savings. If the downstream
device connected to the RC is L1SS capable AND the OS enables L1SS, all
PCIe traffic may abruptly halt, potentially hanging the system.
"default" -- Bidirectional CLKREQ# between the RC and downstream device.
Provides ASPM L0s, L1, and L1SS, but not compliant to provide Clock
Power Management; specifically, may not be able to meet the T_CLRon max
timing of 400ns as specified in "Dynamic Clock Control", section
3.2.5.2.2 of the PCIe Express Mini CEM 2.1 specification. This
situation is atypical and should happen only with older devices.
Previously, this driver always set the mode to "no-l1ss", as almost all
STB/CM boards operate in this mode. But now there is interest in
activating L1SS power savings from STB/CM customers, which requires "aspm"
mode. In addition, a bug was filed for RPi4 CM platform because most
devices did not work in "no-l1ss" mode.
Note that the mode is specified by the DT property "brcm,clkreq-mode". If
this property is omitted, then "default" mode is chosen.
Note: Since L1 substates are now possible, a modification was made
regarding an internal bus timeout: During long periods of the PCIe RC HW
being in an L1SS sleep state, there may be a timeout on an internal bus
access, even though there may not be any PCIe access involved. Such a
timeout will cause a subsequent CPU abort.
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217276
Link: https://lore.kernel.org/linux-pci/20231113185607.1756-3-james.quinlan@broadcom.com
Tested-by: Cyril Brulebois <cyril@debamax.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
|
|
The Broadcom STB/CM PCIe HW -- a core that is also used by RPi SOCs --
requires the driver to deliberately place the RC HW one of three CLKREQ#
modes. The "brcm,clkreq-mode" property allows the user to override the
default setting. If this property is omitted, the default mode shall be
"default".
Link: https://lore.kernel.org/linux-pci/20231113185607.1756-2-james.quinlan@broadcom.com
Tested-by: Cyril Brulebois <cyril@debamax.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
|
|
When calling spi_register_board_info(),
Fixes: f869d42e580f ("MIPS: Alchemy: Improved DB1550 support, with audio and serial busses.")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
When calling spi_register_board_info(), we should pass the number of
elements in 'db1200_spi_devs', not 'db1200_i2c_devs'.
Fixes: 63323ec54a7e ("MIPS: Alchemy: Extended DB1200 board support.")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs into vfs.netfs
Pull netfs updates from David Howells:
A few follow-up fixes for the netfs work for this cycle.
* tag 'netfs-lib-20240109' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
netfs: Fix wrong #ifdef hiding wait
cachefiles: Fix signed/unsigned mixup
netfs: Fix the loop that unmarks folios after writing to the cache
netfs: Fix interaction between write-streaming and cachefiles culling
netfs: Count DIO writes
netfs: Mark netfs_unbuffered_write_iter_locked() static
Tested-by: Marc Dionne <marc.dionne@auristor.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
This reverts commit dad3fb67ca1cbef87ce700e83a55835e5921ce8a.
The commit converted kernfs_idr_lock to an IRQ-safe raw_spinlock because it
could be acquired while holding an rq lock through bpf_cgroup_from_id().
However, kernfs_idr_lock is held while doing GPF_NOWAIT allocations which
involves acquiring an non-IRQ-safe and non-raw lock leading to the following
lockdep warning:
=============================
[ BUG: Invalid wait context ]
6.7.0-rc5-kzm9g-00251-g655022a45b1c #578 Not tainted
-----------------------------
swapper/0/0 is trying to lock:
dfbcd488 (&c->lock){....}-{3:3}, at: local_lock_acquire+0x0/0xa4
other info that might help us debug this:
context-{5:5}
2 locks held by swapper/0/0:
#0: dfbc9c60 (lock){+.+.}-{3:3}, at: local_lock_acquire+0x0/0xa4
#1: c0c012a8 (kernfs_idr_lock){....}-{2:2}, at: __kernfs_new_node.constprop.0+0x68/0x258
stack backtrace:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 6.7.0-rc5-kzm9g-00251-g655022a45b1c #578
Hardware name: Generic SH73A0 (Flattened Device Tree)
unwind_backtrace from show_stack+0x10/0x14
show_stack from dump_stack_lvl+0x68/0x90
dump_stack_lvl from __lock_acquire+0x3cc/0x168c
__lock_acquire from lock_acquire+0x274/0x30c
lock_acquire from local_lock_acquire+0x28/0xa4
local_lock_acquire from ___slab_alloc+0x234/0x8a8
___slab_alloc from __slab_alloc.constprop.0+0x30/0x44
__slab_alloc.constprop.0 from kmem_cache_alloc+0x7c/0x148
kmem_cache_alloc from radix_tree_node_alloc.constprop.0+0x44/0xdc
radix_tree_node_alloc.constprop.0 from idr_get_free+0x110/0x2b8
idr_get_free from idr_alloc_u32+0x9c/0x108
idr_alloc_u32 from idr_alloc_cyclic+0x50/0xb8
idr_alloc_cyclic from __kernfs_new_node.constprop.0+0x88/0x258
__kernfs_new_node.constprop.0 from kernfs_create_root+0xbc/0x154
kernfs_create_root from sysfs_init+0x18/0x5c
sysfs_init from mnt_init+0xc4/0x220
mnt_init from vfs_caches_init+0x6c/0x88
vfs_caches_init from start_kernel+0x474/0x528
start_kernel from 0x0
Let's rever the commit. It's undesirable to spread out raw spinlock usage
anyway and the problem can be solved by protecting the lookup path with RCU
instead.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Andrea Righi <andrea.righi@canonical.com>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: http://lkml.kernel.org/r/CAMuHMdV=AKt+mwY7svEq5gFPx41LoSQZ_USME5_MEdWQze13ww@mail.gmail.com
Link: https://lore.kernel.org/r/20240109214828.252092-2-tj@kernel.org
Tested-by: Andrea Righi <andrea.righi@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
These are all options for boards that got removed in the past and
are not relevant here because the options no longer exist or
are implied by the platform.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
SLUB is now the only remaining allocator after the SLAB removal and it
was the default already before that, so no need to mention it in the
defconfig files.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
CONFIG_NET_ETHERNET was removed a long time ago in f860b0522f65 ("drivers/net:
Kconfig and Makefile cleanup"). Remove the last references to in in ARM
defconfig files.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
These were removed last year in commit 721da5cee9d4 ("driver core:
remove CONFIG_SYSFS_DEPRECATED and CONFIG_SYSFS_DEPRECATED_V2"),
so remove the last references to them in arm config files.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
As part of general housekeeping, change the defconfig files to
sort lines based on the 'make savedefconfig' output, to make
it easier to do additional changes on top.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
A number of options got reorganized over time wihtin Kconfig, so make sure
everything is where it belongs in order to simplify defconfig changes
again in the future.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
We're only allocating from the realtime device if the inode is marked
for realtime and we're /not/ allocating into the attr fork.
Fixes: 58643460546d ("xfs: also use xfs_bmap_btalloc_accounting for RT allocations")
Signed-off-by: "Darrick J. Wong" <djwong@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Chandan Babu R <chandanbabu@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Alexander Gordeev:
- Add machine variable capacity information to /proc/sysinfo.
- Limit the waste of page tables and always align vmalloc area size and
base address on segment boundary.
- Fix a memory leak when an attempt to register interruption sub class
(ISC) for the adjunct-processor (AP) guest failed.
- Reset response code AP_RESPONSE_INVALID_GISA to understandable by
guest AP_RESPONSE_INVALID_ADDRESS in response to a failed
interruption sub class (ISC) registration attempt.
- Improve reaction to adjunct-processor (AP)
AP_RESPONSE_OTHERWISE_CHANGED response code when enabling interrupts
on behalf of a guest.
- Fix incorrect sysfs 'status' attribute of adjunct-processor (AP)
queue device bound to the vfio_ap device driver when the mediated
device is attached to a guest, but the queue device is not passed
through.
- Rework struct ap_card to hold the whole adjunct-processor (AP) card
hardware information. As result, all the ugly bit checks are replaced
by simple evaluations of the required bit fields.
- Improve handling of some weird scenarios between service element (SE)
host and SE guest with adjunct-processor (AP) pass-through support.
- Change local_ctl_set_bit() and local_ctl_clear_bit() so they return
the previous value of the to be changed control register. This is
useful if a bit is only changed temporarily and the previous content
needs to be restored.
- The kernel starts with machine checks disabled and is expected to
enable it once trap_init() is called. However the implementation
allows machine checks early. Consistently enable it in trap_init()
only.
- local_mcck_disable() and local_mcck_enable() assume that machine
checks are always enabled. Instead implement and use
local_mcck_save() and local_mcck_restore() to disable machine checks
and restore the previous state.
- Modification of floating point control (FPC) register of a traced
process using ptrace interface may lead to corruption of the FPC
register of the tracing process. Fix this.
- kvm_arch_vcpu_ioctl_set_fpu() allows to set the floating point
control (FPC) register in vCPU, but may lead to corruption of the FPC
register of the host process. Fix this.
- Use READ_ONCE() to read a vCPU floating point register value from the
memory mapped area. This avoids that, depending on code generation, a
different value is tested for validity than the one that is used.
- Get rid of test_fp_ctl(), since it is quite subtle to use it
correctly. Instead copy a new floating point control register value
into its save area and test the validity of the new value when
loading it.
- Remove superfluous save_fpu_regs() call.
- Remove s390 support for ARCH_WANTS_DYNAMIC_TASK_STRUCT. All machines
provide the vector facility since many years and the need to make the
task structure size dependent on the vector facility does not exist.
- Remove the "novx" kernel command line option, as the vector code runs
without any problems since many years.
- Add the vector facility to the z13 architecture level set (ALS). All
hypervisors support the vector facility since many years. This allows
compile time optimizations of the kernel.
- Get rid of MACHINE_HAS_VX and replace it with cpu_has_vx(). As
result, the compiled code will have less runtime checks and less
code.
- Convert pgste_get_lock() and pgste_set_unlock() ASM inlines to C.
- Convert the struct subchannel spinlock from pointer to member.
* tag 's390-6.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (24 commits)
Revert "s390: update defconfigs"
s390/cio: make sch->lock spinlock pointer a member
s390: update defconfigs
s390/mm: convert pgste locking functions to C
s390/fpu: get rid of MACHINE_HAS_VX
s390/als: add vector facility to z13 architecture level set
s390/fpu: remove "novx" option
s390/fpu: remove ARCH_WANTS_DYNAMIC_TASK_STRUCT support
KVM: s390: remove superfluous save_fpu_regs() call
s390/fpu: get rid of test_fp_ctl()
KVM: s390: use READ_ONCE() to read fpc register value
KVM: s390: fix setting of fpc register
s390/ptrace: handle setting of fpc register correctly
s390/nmi: implement and use local_mcck_save() / local_mcck_restore()
s390/nmi: consistently enable machine checks in trap_init()
s390/ctlreg: return old register contents when changing bits
s390/ap: handle outband SE bind state change
s390/ap: store TAPQ hwinfo in struct ap_card
s390/vfio-ap: fix sysfs status attribute for AP queue devices
s390/vfio-ap: improve reaction to response code 07 from PQAP(AQIC) command
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic cleanups from Arnd Bergmann:
"A series from Baoquan He cleans up the asm-generic/io.h to remove the
ioremap_uc() definition from everything except x86, which still needs
it for pre-PAT systems. This series notably contains a patch from
Jiaxun Yang that converts MIPS to use asm-generic/io.h like every
other architecture does, enabling future cleanups.
Some of my own patches fix -Wmissing-prototype warnings in
architecture specific code across several architectures. This is now
needed as the warning is enabled by default. There are still some
remaining warnings in minor platforms, but the series should catch
most of the widely used ones make them more consistent with one
another.
David McKay fixes a bug in __generic_cmpxchg_local() when this is used
on 64-bit architectures. This could currently only affect parisc64 and
sparc64.
Additional cleanups address from Linus Walleij, Uwe Kleine-König,
Thomas Huth, and Kefeng Wang help reduce unnecessary inconsistencies
between architectures"
* tag 'asm-generic-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
asm-generic: Fix 32 bit __generic_cmpxchg_local
Hexagon: Make pfn accessors statics inlines
ARC: mm: Make virt_to_pfn() a static inline
mips: remove extraneous asm-generic/iomap.h include
sparc: Use $(kecho) to announce kernel images being ready
arm64: vdso32: Define BUILD_VDSO32_64 to correct prototypes
csky: fix arch_jump_label_transform_static override
arch: add do_page_fault prototypes
arch: add missing prepare_ftrace_return() prototypes
arch: vdso: consolidate gettime prototypes
arch: include linux/cpu.h for trap_init() prototype
arch: fix asm-offsets.c building with -Wmissing-prototypes
arch: consolidate arch_irq_work_raise prototypes
hexagon: Remove CONFIG_HEXAGON_ARCH_VERSION from uapi header
asm/io: remove unnecessary xlate_dev_mem_ptr() and unxlate_dev_mem_ptr()
mips: io: remove duplicated codes
arch/*/io.h: remove ioremap_uc in some architectures
mips: add <asm-generic/io.h> including
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mcgrof/linux
Pull module updates from Luis Chamberlain:
"Just one cleanup and one documentation improvement change. No
functional changes"
* tag 'modules-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mcgrof/linux:
kernel/module: improve documentation for try_module_get()
module: Remove redundant TASK_UNINTERRUPTIBLE
|
|
The wording in the current documentation is a little strong. The
intention was not to fix any particular interrupt as wakeup capable but
leave those details to the device. It wasn't intended to enforce any
rules as what can be or can't be a wakeup interrupt.
Soften the wording to not mandate that the 'wakeup-source' property be
used, and clarify what it means when an interrupt is marked (or not
marked) for wakeup.
Link: https://lore.kernel.org/all/ZYAjxxHcCOgDVMTQ@bogus/
Link: https://lore.kernel.org/all/CAL_Jsq+MYwOG40X26cYmO9EkZ9xqWrXDi03MaRfxnV-+VGkXWQ@mail.gmail.com/
Signed-off-by: Mark Hasemeyer <markhas@chromium.org>
Link: https://lore.kernel.org/r/20240102140734.v4.4.I1016a45ac9e8daf8a9ebc9854ab90ec3542e7c30@changeid
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mcgrof/linux
Pull sysctl updates from Luis Chamberlain:
"To help make the move of sysctls out of kernel/sysctl.c not incur a
size penalty sysctl has been changed to allow us to not require the
sentinel, the final empty element on the sysctl array. Joel Granados
has been doing all this work.
In the v6.6 kernel we got the major infrastructure changes required to
support this. For v6.7 we had all arch/ and drivers/ modified to
remove the sentinel. For v6.8-rc1 we get a few more updates for fs/
directory only.
The kernel/ directory is left but we'll save that for v6.9-rc1 as
those patches are still being reviewed. After that we then can expect
also the removal of the no longer needed check for procname == NULL.
Let us recap the purpose of this work:
- this helps reduce the overall build time size of the kernel and run
time memory consumed by the kernel by about ~64 bytes per array
- the extra 64-byte penalty is no longer inncurred now when we move
sysctls out from kernel/sysctl.c to their own files
Thomas Weißschuh also sent a few cleanups, for v6.9-rc1 we expect to
see further work by Thomas Weißschuh with the constificatin of the
struct ctl_table.
Due to Joel Granados's work, and to help bring in new blood, I have
suggested for him to become a maintainer and he's accepted. So for
v6.9-rc1 I look forward to seeing him sent you a pull request for
further sysctl changes. This also removes Iurii Zaikin as a maintainer
as he has moved on to other projects and has had no time to help at
all"
* tag 'sysctl-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mcgrof/linux:
sysctl: remove struct ctl_path
sysctl: delete unused define SYSCTL_PERM_EMPTY_DIR
coda: Remove the now superfluous sentinel elements from ctl_table array
sysctl: Remove the now superfluous sentinel elements from ctl_table array
fs: Remove the now superfluous sentinel elements from ctl_table array
cachefiles: Remove the now superfluous sentinel element from ctl_table array
sysclt: Clarify the results of selftest run
sysctl: Add a selftest for handling empty dirs
sysctl: Fix out of bounds access for empty sysctl registers
MAINTAINERS: Add Joel Granados as co-maintainer for proc sysctl
MAINTAINERS: remove Iurii Zaikin from proc sysctl
|
|
Pull header cleanups from Kent Overstreet:
"The goal is to get sched.h down to a type only header, so the main
thing happening in this patchset is splitting out various _types.h
headers and dependency fixups, as well as moving some things out of
sched.h to better locations.
This is prep work for the memory allocation profiling patchset which
adds new sched.h interdepencencies"
* tag 'header_cleanup-2024-01-10' of https://evilpiepirate.org/git/bcachefs: (51 commits)
Kill sched.h dependency on rcupdate.h
kill unnecessary thread_info.h include
Kill unnecessary kernel.h include
preempt.h: Kill dependency on list.h
rseq: Split out rseq.h from sched.h
LoongArch: signal.c: add header file to fix build error
restart_block: Trim includes
lockdep: move held_lock to lockdep_types.h
sem: Split out sem_types.h
uidgid: Split out uidgid_types.h
seccomp: Split out seccomp_types.h
refcount: Split out refcount_types.h
uapi/linux/resource.h: fix include
x86/signal: kill dependency on time.h
syscall_user_dispatch.h: split out *_types.h
mm_types_task.h: Trim dependencies
Split out irqflags_types.h
ipc: Kill bogus dependency on spinlock.h
shm: Slim down dependencies
workqueue: Split out workqueue_types.h
...
|
|
Pull bcachefs updates from Kent Overstreet:
- btree write buffer rewrite: instead of adding keys to the btree write
buffer at transaction commit time, we now journal them with a
different journal entry type and copy them from the journal to the
write buffer just prior to journal write.
This reduces the number of atomic operations on shared cachelines in
the transaction commit path and is a signicant performance
improvement on some workloads: multithreaded 4k random writes went
from ~650k iops to ~850k iops.
- Bring back optimistic spinning for six locks: the new implementation
doesn't use osq locks; instead we add to the lock waitlist as normal,
and then spin on the lock_acquired bit in the waitlist entry, _not_
the lock itself.
- New ioctls:
- BCH_IOCTL_DEV_USAGE_V2, which allows for new data types
- BCH_IOCTL_OFFLINE_FSCK, which runs the kernel implementation of
fsck but without mounting: useful for transparently using the
kernel version of fsck from 'bcachefs fsck' when the kernel
version is a better match for the on disk filesystem.
- BCH_IOCTL_ONLINE_FSCK: online fsck. Not all passes are supported
yet, but the passes that are supported are fully featured - errors
may be corrected as normal.
The new ioctls use the new 'thread_with_file' abstraction for kicking
off a kthread that's tied to a file descriptor returned to userspace
via the ioctl.
- btree_paths within a btree_trans are now dynamically growable,
instead of being limited to 64. This is important for the
check_directory_structure phase of fsck, and also fixes some issues
we were having with btree path overflow in the reflink btree.
- Trigger refactoring; prep work for the upcoming disk space accounting
rewrite
- Numerous bugfixes :)
* tag 'bcachefs-2024-01-10' of https://evilpiepirate.org/git/bcachefs: (226 commits)
bcachefs: eytzinger0_find() search should be const
bcachefs: move "ptrs not changing" optimization to bch2_trigger_extent()
bcachefs: fix simulateously upgrading & downgrading
bcachefs: Restart recovery passes more reliably
bcachefs: bch2_dump_bset() doesn't choke on u64s == 0
bcachefs: improve checksum error messages
bcachefs: improve validate_bset_keys()
bcachefs: print sb magic when relevant
bcachefs: __bch2_sb_field_to_text()
bcachefs: %pg is banished
bcachefs: Improve would_deadlock trace event
bcachefs: fsck_err()s don't need to manually check c->sb.version anymore
bcachefs: Upgrades now specify errors to fix, like downgrades
bcachefs: no thread_with_file in userspace
bcachefs: Don't autofix errors we can't fix
bcachefs: add missing bch2_latency_acct() call
bcachefs: increase max_active on io_complete_wq
bcachefs: add time_stats for btree_node_read_done()
bcachefs: don't clear accessed bit in btree node fill
bcachefs: Add an option to control btree node prefetching
...
|
|
Pull smb client fixes from Steve French:
"Various smb client fixes, most related to better handling special file
types:
- Improve handling of special file types:
- performance improvement (better compounding and better caching
of readdir entries that are reparse points)
- extend support for creating special files (sockets, fifos,
block/char devices)
- fix renaming and hardlinking of reparse points
- extend support for creating symlinks with IO_REPARSE_TAG_SYMLINK
- Multichannel logging improvement
- Exception handling fix
- Minor cleanups"
* tag 'v6.8-rc-part1-smb-client' of git://git.samba.org/sfrench/cifs-2.6:
cifs: update internal module version number for cifs.ko
cifs: remove unneeded return statement
cifs: make cifs_chan_update_iface() a void function
cifs: delete unnecessary NULL checks in cifs_chan_update_iface()
cifs: get rid of dup length check in parse_reparse_point()
smb: client: stop revalidating reparse points unnecessarily
cifs: Pass unbyteswapped eof value into SMB2_set_eof()
smb3: Improve exception handling in allocate_mr_list()
cifs: fix in logging in cifs_chan_update_iface
smb: client: handle special files and symlinks in SMB3 POSIX
smb: client: cleanup smb2_query_reparse_point()
smb: client: allow creating symlinks via reparse points
smb: client: fix hardlinking of reparse points
smb: client: fix renaming of reparse points
smb: client: optimise reparse point querying
smb: client: allow creating special files via reparse points
smb: client: extend smb2_compound_op() to accept more commands
smb: client: Fix minor whitespace errors and warnings
|
|
Pull nfs client updates from Anna Schumaker:
"New Features:
- Always ask for type with READDIR
- Remove nfs_writepage()
Bugfixes:
- Fix a suspicious RCU usage warning
- Fix a blocklayoutdriver reference leak
- Fix the block driver's calculation of layoutget size
- Fix handling NFS4ERR_RETURNCONFLICT
- Fix _xprt_switch_find_current_entry()
- Fix v4.1 backchannel request timeouts
- Don't add zero-length pnfs block devices
- Use the parent cred in nfs_access_login_time()
Cleanups:
- A few improvements when dealing with referring calls from the
server
- Clean up various unused variables, struct fields, and function
calls
- Various tracepoint improvements"
* tag 'nfs-for-6.8-1' of git://git.linux-nfs.org/projects/anna/linux-nfs: (21 commits)
NFSv4.1: Use the nfs_client's rpc timeouts for backchannel
SUNRPC: Fixup v4.1 backchannel request timeouts
rpc_pipefs: Replace one label in bl_resolve_deviceid()
nfs: Remove writepage
NFS: drop unused nfs_direct_req bytes_left
pNFS: Fix the pnfs block driver's calculation of layoutget size
nfs: print fileid in lookup tracepoints
nfs: rename the nfs_async_rename_done tracepoint
nfs: add new tracepoint at nfs4 revalidate entry point
SUNRPC: fix _xprt_switch_find_current_entry logic
NFSv4.1/pnfs: Ensure we handle the error NFS4ERR_RETURNCONFLICT
NFSv4.1: if referring calls are complete, trust the stateid argument
NFSv4: Track the number of referring calls in struct cb_process_state
NFS: Use parent's objective cred in nfs_access_login_time()
NFSv4: Always ask for type with READDIR
pnfs/blocklayout: Don't add zero-length pnfs_block_dev
blocklayoutdriver: Fix reference leak of pnfs_device_node
SUNRPC: Fix a suspicious RCU usage warning
SUNRPC: Create a helper function for accessing the rpc_clnt's xprt_switch
SUNRPC: Remove unused function rpc_clnt_xprt_switch_put()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 updates from Ted Ts'o:
"Various ext4 bug fixes and cleanups. The fixes are mostly in the
fstrim and mballoc code paths.
Also enable dioread_nolock in the case where the block size is less
than the page size (dioread_nolock has been default in the bs == ps
case for quite some time)"
* tag 'ext4_for_linus-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: fix inconsistent between segment fstrim and full fstrim
ext4: fallback to complex scan if aligned scan doesn't work
ext4: convert ext4_da_do_write_end() to take a folio
ext4: allow for the last group to be marked as trimmed
ext4: move ext4_check_bdev_write_error() into nojournal mode
jbd2: abort journal when detecting metadata writeback error of fs dev
jbd2: remove unused 'JBD2_CHECKPOINT_IO_ERROR' and 'j_atomic_flags'
jbd2: replace journal state flag by checking errseq
jbd2: add errseq to detect client fs's bdev writeback error
ext4: improving calculation of 'fe_{len|start}' in mb_find_extent()
ext4: clarify handling of unwritten bh in __ext4_block_zero_page_range()
ext4: treat end of range as exclusive in ext4_zero_range()
ext4: enable dioread_nolock as default for bs < ps case
ext4: delete redundant calculations in ext4_mb_get_buddy_page_lock()
ext4: reduce unnecessary memory allocation in alloc_flex_gd()
ext4: avoid online resizing failures due to oversized flex bg
ext4: remove unnecessary check from alloc_flex_gd()
ext4: unify the type of flexbg_size to unsigned int
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/krisman/unicode
Pull unicode updates from Gabriel Krisman Bertazi:
"Other than the update to MAINTAINERS, this PR has only a fix to stop
ecryptfs from inadvertently mounting case-insensitive filesystems that
it cannot handle, which would otherwise caused post-mount failures"
* tag 'unicode-next-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/krisman/unicode:
MAINTAINERS: update unicode maintainer e-mail address
ecryptfs: Reject casefold directory inodes
|
|
for-6.8/block
Pull NVMe changes from Keith:
"nvme follow-up updates for Linux 6.8
- tcp, fc, and rdma target fixes (Maurizio, Daniel, Hannes, Christoph)
- discard fixes and improvements (Christoph)
- timeout debug improvements (Keith, Max)
- various cleanups (Daniel, Max, Giuxen)
- trace event string fixes (Arnd)
- shadow doorbell setup on reset fix (William)
- a write zeroes quirk for SK Hynix (Jim)"
* tag 'nvme-6.8-2024-1-10' of git://git.infradead.org/nvme: (25 commits)
nvmet-rdma: avoid circular locking dependency on install_queue()
nvmet-tcp: avoid circular locking dependency on install_queue()
nvme-pci: set doorbell config before unquiescing
nvmet-tcp: Fix the H2C expected PDU len calculation
nvme-tcp: enhance timeout kernel log
nvme-rdma: enhance timeout kernel log
nvme-pci: enhance timeout kernel log
nvme: trace: avoid memcpy overflow warning
nvmet: re-fix tracing strncpy() warning
nvme: introduce nvme_disk_is_ns_head helper
nvme-pci: disable write zeroes for SK Hynix BC901
nvmet-fcloop: Remove remote port from list when unlinking
nvmet-trace: avoid dereferencing pointer too early
nvmet-fc: remove unnecessary bracket
nvme: simplify the max_discard_segments calculation
nvme: fix max_discard_sectors calculation
nvme: also skip discard granularity updates in nvme_config_discard
nvme: update the explanation for not updating the limits in nvme_config_discard
nvmet-tcp: fix a missing endianess conversion in nvmet_tcp_try_peek_pdu
nvme-common: mark nvme_tls_psk_prio static
...
|
|
The new vfio-virtio driver already has a dependency on VIRTIO_PCI_ADMIN_LEGACY,
but that is a bool symbol and allows vfio-virtio to be built-in even if
virtio-pci itself is a loadable module. This leads to a link failure:
aarch64-linux-ld: drivers/vfio/pci/virtio/main.o: in function `virtiovf_pci_probe':
main.c:(.text+0xec): undefined reference to `virtio_pci_admin_has_legacy_io'
aarch64-linux-ld: drivers/vfio/pci/virtio/main.o: in function `virtiovf_pci_init_device':
main.c:(.text+0x260): undefined reference to `virtio_pci_admin_legacy_io_notify_info'
aarch64-linux-ld: drivers/vfio/pci/virtio/main.o: in function `virtiovf_pci_bar0_rw':
main.c:(.text+0x6ec): undefined reference to `virtio_pci_admin_legacy_common_io_read'
aarch64-linux-ld: main.c:(.text+0x6f4): undefined reference to `virtio_pci_admin_legacy_device_io_read'
aarch64-linux-ld: main.c:(.text+0x7f0): undefined reference to `virtio_pci_admin_legacy_common_io_write'
aarch64-linux-ld: main.c:(.text+0x7f8): undefined reference to `virtio_pci_admin_legacy_device_io_write'
Add another explicit dependency on the tristate symbol.
Fixes: eb61eca0e8c3 ("vfio/virtio: Introduce a vfio driver over virtio devices")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Link: https://lore.kernel.org/r/20240109075731.2726731-1-arnd@kernel.org
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
nvmet_rdma_install_queue() is driven from the ->io_work workqueue
function, but will call flush_workqueue() which might trigger
->release_work() which in itself calls flush_work on ->io_work.
To avoid that check for pending queue in disconnecting status,
and return 'controller busy' when we reached a certain threshold.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Tested-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
nvmet_tcp_install_queue() is driven from the ->io_work workqueue
function, but will call flush_workqueue() which might trigger
->release_work() which in itself calls flush_work on ->io_work.
To avoid that check for pending queue in disconnecting status,
and return 'controller busy' when we reached a certain threshold.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Tested-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
Fix the size check added to dns_resolver_preparse() for the V1 server-list
header so that it doesn't give EINVAL if the size supplied is the same as
the size of the header struct (which should be valid).
This can be tested with:
echo -n -e '\0\0\01\xff\0\0' | keyctl padd dns_resolver desc @p
which will give "add_key: Invalid argument" without this fix.
Fixes: 1997b3cb4217 ("keys, dns: Fix missing size check of V1 server-list header")
Reported-by: Pengfei Xu <pengfei.xu@intel.com>
Link: https://lore.kernel.org/r/ZZ4fyY4r3rqgZL+4@xpf.sh.intel.com/
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto updates from Herbert Xu:
"API:
- Add incremental lskcipher/skcipher processing
Algorithms:
- Remove SHA1 from drbg
- Remove CFB and OFB
Drivers:
- Add comp high perf mode configuration in hisilicon/zip
- Add support for 420xx devices in qat
- Add IAA Compression Accelerator driver"
* tag 'v6.8-p1' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (172 commits)
crypto: iaa - Account for cpu-less numa nodes
crypto: scomp - fix req->dst buffer overflow
crypto: sahara - add support for crypto_engine
crypto: sahara - remove error message for bad aes request size
crypto: sahara - remove unnecessary NULL assignments
crypto: sahara - remove 'active' flag from sahara_aes_reqctx struct
crypto: sahara - use dev_err_probe()
crypto: sahara - use devm_clk_get_enabled()
crypto: sahara - use BIT() macro
crypto: sahara - clean up macro indentation
crypto: sahara - do not resize req->src when doing hash operations
crypto: sahara - fix processing hash requests with req->nbytes < sg->length
crypto: sahara - improve error handling in sahara_sha_process()
crypto: sahara - fix wait_for_completion_timeout() error handling
crypto: sahara - fix ahash reqsize
crypto: sahara - handle zero-length aes requests
crypto: skcipher - remove excess kerneldoc members
crypto: shash - remove excess kerneldoc members
crypto: qat - generate dynamically arbiter mappings
crypto: qat - add support for ring pair level telemetry
...
|
|
Before commit 7839d0078e0d ("PM: sleep: Fix possible deadlocks in core
system-wide PM code"), the resume of devices that were allowed to resume
asynchronously was scheduled before starting the resume of the other
devices, so the former did not have to wait for the latter unless
functional dependencies were present.
Commit 7839d0078e0d removed that optimization in order to address a
correctness issue, but it can be restored with the help of a new device
power management flag, so do that now.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jarkko/linux-tpmdd
Pull tpm updates from Jarkko Sakkinen:
"Just a couple fixes and no new features"
* tag 'tpmdd-v6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/jarkko/linux-tpmdd:
tpm: cr50: fix kernel-doc warning and spelling
tpm: nuvoton: Use i2c_get_match_data()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull hardening updates from Kees Cook:
- Introduce the param_unknown_fn type and other clean ups (Andy
Shevchenko)
- Various __counted_by annotations (Christophe JAILLET, Gustavo A. R.
Silva, Kees Cook)
- Add KFENCE test to LKDTM (Stephen Boyd)
- Various strncpy() refactorings (Justin Stitt)
- Fix qnx4 to avoid writing into the smaller of two overlapping buffers
- Various strlcpy() refactorings
* tag 'hardening-v6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
qnx4: Use get_directory_fname() in qnx4_match()
qnx4: Extract dir entry filename processing into helper
atags_proc: Add __counted_by for struct buffer and use struct_size()
tracing/uprobe: Replace strlcpy() with strscpy()
params: Fix multi-line comment style
params: Sort headers
params: Use size_add() for kmalloc()
params: Do not go over the limit when getting the string length
params: Introduce the param_unknown_fn type
lkdtm: Add kfence read after free crash type
nvme-fc: replace deprecated strncpy with strscpy
nvdimm/btt: replace deprecated strncpy with strscpy
nvme-fabrics: replace deprecated strncpy with strscpy
drm/modes: replace deprecated strncpy with strscpy_pad
afs: Add __counted_by for struct afs_acl and use struct_size()
VMCI: Annotate struct vmci_handle_arr with __counted_by
i40e: Annotate struct i40e_qvlist_info with __counted_by
HID: uhid: replace deprecated strncpy with strscpy
samples: Replace strlcpy() with strscpy()
SUNRPC: Replace strlcpy() with strscpy()
|
|
Suppose we issue two FITRIM ioctls for ranges [0,15] and [16,31] with
mininum length of trimmed range set to 8 blocks. If we have say a range of
blocks 10-22 free, this range will not be trimmed because it straddles the
boundary of the two FITRIM ranges and neither part is big enough. This is a
bit surprising to some users that call FITRIM on smaller ranges of blocks
to limit impact on the system. Also XFS trims all free space extents that
overlap with the specified range so we are inconsistent among filesystems.
Let's change ext4_try_to_trim_range() to consider for trimming the whole
free space extent that straddles the end of specified range, not just the
part of it within the range.
Signed-off-by: Ye Bin <yebin10@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20231216010919.1995851-1-yebin10@huawei.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
Currently in case the goal length is a multiple of stripe size we use
ext4_mb_scan_aligned() to find the stripe size aligned physical blocks.
In case we are not able to find any, we again go back to calling
ext4_mb_choose_next_group() to search for a different suitable block
group. However, since the linear search always begins from the start,
most of the times we end up with the same BG and the cycle continues.
With large fliesystems, the CPU can be stuck in this loop for hours
which can slow down the whole system. Hence, until we figure out a
better way to continue the search (rather than starting from beginning)
in ext4_mb_choose_next_group(), lets just fallback to
ext4_mb_complex_scan_group() in case aligned scan fails, as it is much
more likely to find the needed blocks.
Signed-off-by: Ojaswin Mujoo <ojaswin@linux.ibm.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/ee033f6dfa0a7f2934437008a909c3788233950f.1702455010.git.ojaswin@linux.ibm.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
There's nothing page-specific happening in ext4_da_do_write_end();
it's merely used for its refcount & lock, both of which are folio
properties. Saves four calls to compound_head().
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20231214053035.1018876-1-willy@infradead.org
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
The ext4 filesystem tracks the trim status of blocks at the group
level. When an entire group has been trimmed then it is marked as
such and subsequent trim invocations with the same minimum trim size
will not be attempted on that group unless it is marked as able to be
trimmed again such as when a block is freed.
Currently the last group can't be marked as trimmed due to incorrect
logic in ext4_last_grp_cluster(). ext4_last_grp_cluster() is supposed
to return the zero based index of the last cluster in a group. This is
then used by ext4_try_to_trim_range() to determine if the trim
operation spans the entire group and as such if the trim status of the
group should be recorded.
ext4_last_grp_cluster() takes a 0 based group index, thus the valid
values for grp are 0..(ext4_get_groups_count - 1). Any group index
less than (ext4_get_groups_count - 1) is not the last group and must
have EXT4_CLUSTERS_PER_GROUP(sb) clusters. For the last group we need
to calculate the number of clusters based on the number of blocks in
the group. Finally subtract 1 from the number of clusters as zero
based indexing is expected. Rearrange the function slightly to make
it clear what we are calculating and returning.
Reproducer:
// Create file system where the last group has fewer blocks than
// blocks per group
$ mkfs.ext4 -b 4096 -g 8192 /dev/nvme0n1 8191
$ mount /dev/nvme0n1 /mnt
Before Patch:
$ fstrim -v /mnt
/mnt: 25.9 MiB (27156480 bytes) trimmed
// Group not marked as trimmed so second invocation still discards blocks
$ fstrim -v /mnt
/mnt: 25.9 MiB (27156480 bytes) trimmed
After Patch:
fstrim -v /mnt
/mnt: 25.9 MiB (27156480 bytes) trimmed
// Group marked as trimmed so second invocation DOESN'T discard any blocks
fstrim -v /mnt
/mnt: 0 B (0 bytes) trimmed
Fixes: 45e4ab320c9b ("ext4: move setting of trimmed bit into ext4_try_to_trim_range()")
Cc: <stable@vger.kernel.org> # 4.19+
Signed-off-by: Suraj Jitindar Singh <surajjs@amazon.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20231213051635.37731-1-surajjs@amazon.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull pstore updates from Kees Cook:
- Do not allow misconfigured ECC sizes (Sergey Shtylyov)
- Allow for odd number of CPUs (Weichen Chen)
- Refactor error handling to use cleanup.h
* tag 'pstore-v6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
pstore: inode: Use cleanup.h for struct pstore_private
pstore: inode: Use __free(pstore_iput) for inode allocations
pstore: inode: Convert mutex usage to guard(mutex)
pstore: inode: Convert kfree() usage to __free(kfree)
pstore: ram_core: fix possible overflow in persistent_ram_init_ecc()
pstore/ram: Fix crash when setting number of cpus to an odd number
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/overlayfs/vfs
Pull overlayfs updates from Amir Goldstein:
"This is a very small update with no bug fixes and no new features.
The larger update of overlayfs for this cycle, the re-factoring of
overlayfs code into generic backing_file helpers, was already merged
via Christian.
Summary:
- Simplify/clarify some code
No bug fixes here, just some changes following questions from Al
about overlayfs code that could be a little more simple to follow.
- Overlayfs documentation style fixes
Mainly fixes for ReST formatting suggested by documentation
developers"
* tag 'ovl-update-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/overlayfs/vfs:
overlayfs.rst: fix ReST formatting
overlayfs.rst: use consistent feature names
ovl: initialize ovl_copy_up_ctx.destname inside ovl_do_copy_up()
ovl: remove redundant ofs->indexdir member
|
|
This originally came from the aio side, and it's laid out rather oddly.
The common case here is that we either get -EIOCBQUEUED from submitting
an async request, or that we complete the request correctly with the
given number of bytes. Handling the odd internal restart error codes
is not a common operation.
Lay it out a bit more optimally that better explains the normal flow,
and switch to avoiding the indirect call completely as this is our
kiocb and we know the completion handler can only be one of two
possible variants. While at it, move it to where it belongs in the
file, with fellow end IO helpers.
Outside of being easier to read, this also reduces the text size of the
function by 24 bytes for me on arm64.
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs
Pull erofs updates from Gao Xiang:
"In this cycle, we'd like to enable basic sub-page compressed data
support for Android ecosystem (for vendors to try out 16k page size
with 4k-block images in their compatibility mode) as well as container
images (so that 4k-block images can be parsed on arm64 cloud servers
using 64k page size.)
In addition, there are several bugfixes and cleanups as usual. All
commits have been in -next for a while and no potential merge conflict
is observed.
Summary:
- Add basic sub-page compressed data support
- Fix a memory leak on MicroLZMA and DEFLATE compression
- Fix a rare LZ4 inplace decompression issue on recent x86 CPUs
- Fix a KASAN issue reported by syzbot around crafted images
- Some cleanups"
* tag 'erofs-for-6.8-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs:
erofs: make erofs_{err,info}() support NULL sb parameter
erofs: avoid debugging output for (de)compressed data
erofs: allow partially filled compressed bvecs
erofs: enable sub-page compressed block support
erofs: refine z_erofs_transform_plain() for sub-page block support
erofs: fix ztailpacking for subpage compressed blocks
erofs: fix up compacted indexes for block size < 4096
erofs: record `pclustersize` in bytes instead of pages
erofs: support I/O submission for sub-page compressed blocks
erofs: fix lz4 inplace decompression
erofs: fix memory leak on short-lived bounced pages
|
|
During resets, if queues are unquiesced first, then the host can submit
IOs to the controller using shadow doorbell logic but the controller
won't be aware. This can lead to necessary MMIO doorbells from being
not issued, causing requests to be delayed and timed-out.
Signed-off-by: William Butler <wab@google.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
Pull fscrypt updates from Eric Biggers:
"Adjust the timing of the fscrypt keyring destruction, to prepare for
btrfs's fscrypt support.
Also document that CephFS supports fscrypt now"
* tag 'fscrypt-for-linus' of git://git.kernel.org/pub/scm/fs/fscrypt/linux:
fs: move fscrypt keyring destruction to after ->put_super
f2fs: move release of block devices to after kill_block_super()
fscrypt: document that CephFS supports fscrypt now
fscrypt: update comment for do_remove_key()
fscrypt.rst: update definition of struct fscrypt_context_v2
|
|
Pull nfsd updates from Chuck Lever:
"The bulk of the patches for this release are clean-ups and minor bug
fixes.
There is one significant revert to mention: support for RDMA Read
operations in the server's RPC-over-RDMA transport implementation has
been fixed so it waits for Read completion in a way that avoids tying
up an nfsd thread. This prevents a possible DoS vector if an
RPC-over-RDMA client should become unresponsive during RDMA Read
operations.
As always I am grateful to NFSD contributors, reviewers, and testers"
* tag 'nfsd-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux: (56 commits)
nfsd: rename nfsd_last_thread() to nfsd_destroy_serv()
SUNRPC: discard sv_refcnt, and svc_get/svc_put
svc: don't hold reference for poolstats, only mutex.
SUNRPC: remove printk when back channel request not found
svcrdma: Implement multi-stage Read completion again
svcrdma: Copy construction of svc_rqst::rq_arg to rdma_read_complete()
svcrdma: Add back svcxprt_rdma::sc_read_complete_q
svcrdma: Add back svc_rdma_recv_ctxt::rc_pages
svcrdma: Clean up comment in svc_rdma_accept()
svcrdma: Remove queue-shortening warnings
svcrdma: Remove pointer addresses shown in dprintk()
svcrdma: Optimize svc_rdma_cc_init()
svcrdma: De-duplicate completion ID initialization helpers
svcrdma: Move the svc_rdma_cc_init() call
svcrdma: Remove struct svc_rdma_read_info
svcrdma: Update the synopsis of svc_rdma_read_special()
svcrdma: Update the synopsis of svc_rdma_read_call_chunk()
svcrdma: Update synopsis of svc_rdma_read_multiple_chunks()
svcrdma: Update synopsis of svc_rdma_copy_inline_range()
svcrdma: Update the synopsis of svc_rdma_read_data_item()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/teigland/linux-dlm
Pull dlm updates from David Teigland:
"This set cleans up the interface between nfs lockd and dlm, which is
handling nfs file locking for gfs2 and ocfs2. Very basic lockd
functionality is fixed, in which the fl owner was using the lockd pid
instead of the owner value from nfs"
* tag 'dlm-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/linux-dlm:
dlm: update format header reflect current format
dlm: fix format seq ops type 4
dlm: implement EXPORT_OP_ASYNC_LOCK
dlm: use FL_SLEEP to determine blocking vs non-blocking
dlm: use fl_owner from lockd
dlm: use kernel_connect() and kernel_bind()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull afs updates from David Howells:
"The majority of the patches are aimed at fixing and improving the AFS
filesystem's rotation over server IP addresses, but there are also
some fixes from Oleg Nesterov for the use of read_seqbegin_or_lock().
- Fix fileserver probe handling so that the next round of probes
doesn't break ongoing server/address rotation by clearing all the
probe result tracking. This could occasionally cause the rotation
algorithm to drop straight through, give a 'successful' result
without actually emitting any RPC calls, leaving the reply buffer
in an undefined state.
Instead, detach the probe results into a separate struct and
allocate a new one each time we start probing and update the
pointer to it. Probes are also sent in order of address preference
to try and improve the chance that the preferred one will complete
first.
- Fix server rotation so that it uses configurable address
preferences across on the probes that have completed so far than
ranking them by RTT as the latter doesn't necessarily give the best
route. The preference list can be altered by writing into
/proc/net/afs/addr_prefs.
- Fix the handling of Read-Only (and Backup) volume callbacks as
there is one per volume, not one per file, so if someone performs a
command that, say, offlines the volume but doesn't change it, when
it comes back online we don't spam the server with a status fetch
for every vnode we're using. Instead, check the Creation timestamp
in the VolSync record when prompted by a callback break.
- Handle volume regression (ie. a RW volume being restored from a
backup) by scrubbing all cache data for that volume. This is
detected from the VolSync creation timestamp.
- Adjust abort handling and abort -> error mapping to match better
with what other AFS clients do.
- Fix offline and busy volume state handling as they only apply to
individual server instances and not entire volumes and the rotation
algorithm should go and look at other servers if available. Also
make it sleep briefly before each retry if all the volume instances
are unavailable"
* tag 'afs-fix-rotation-20240105' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs: (40 commits)
afs: trace: Log afs_make_call(), including server address
afs: Fix offline and busy message emission
afs: Fix fileserver rotation
afs: Overhaul invalidation handling to better support RO volumes
afs: Parse the VolSync record in the reply of a number of RPC ops
afs: Don't leave DONTUSE/NEWREPSITE servers out of server list
afs: Fix comment in afs_do_lookup()
afs: Apply server breaks to mmap'd files in the call processor
afs: Move the vnode/volume validity checking code into its own file
afs: Defer volume record destruction to a workqueue
afs: Make it possible to find the volumes that are using a server
afs: Combine the endpoint state bools into a bitmask
afs: Keep a record of the current fileserver endpoint state
afs: Dispatch vlserver probes in priority order
afs: Dispatch fileserver probes in priority order
afs: Mark address lists with configured priorities
afs: Provide a way to configure address priorities
afs: Remove the unimplemented afs_cmp_addr_list()
afs: Add some more info to /proc/net/afs/servers
rxrpc: Create a procfile to display outstanding client conn bundles
...
|
|
Pull jfs updates from David Kleikamp:
"Stability improvements"
* tag 'jfs-6.8' of github.com:kleikamp/linux-shaggy:
jfs: Add missing set_freezable() for freezable kthread
jfs: fix array-index-out-of-bounds in diNewExt
jfs: fix shift-out-of-bounds in dbJoin
jfs: fix uaf in jfs_evict_inode
jfs: fix array-index-out-of-bounds in dbAdjTree
jfs: fix slab-out-of-bounds Read in dtSearch
UBSAN: array-index-out-of-bounds in dtSplitRoot
FS:JFS:UBSAN:array-index-out-of-bounds in dbAdjTree
|
|
Track allocated mrs in a list and show warning when leaks are detected
on device free or reset.
Reviewed-by: Gal Pressman <gal@nvidia.com>
Acked-by: Eugenio Pérez <eperezma@redhat.com>
Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com>
Message-Id: <20231225151203.152687-9-dtatulea@nvidia.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Deleting the old mr during mr update (.set_map) and then modifying the
vqs with the new mr is not a good flow for firmware. The firmware
expects that mkeys are deleted after there are no more vqs referencing
them.
Introduce reference counting for mrs to fix this. It is the only way to
make sure that mkeys are not in use by vqs.
An mr reference is taken when the mr is associated to the mr asid table
and when the mr is linked to the vq on create/modify. The reference is
released when the mkey is unlinked from the vq (trough modify/destroy)
and from the mr asid table.
To make things consistent, get rid of mlx5_vdpa_destroy_mr and use
get/put semantics everywhere.
Reviewed-by: Gal Pressman <gal@nvidia.com>
Acked-by: Eugenio Pérez <eperezma@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com>
Message-Id: <20231225151203.152687-8-dtatulea@nvidia.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
